Wired guest access - Unable to access network

Hello,
I've configured two WLC's with the exact same config one of them has working Wired guest network the other one does not.
The only difference in the two I know of is that the one that does not work is connected to a Cisco 3550 switch, the one that works is connected to a Cisco 7600.
The problem is when I connect a computer to the wired guest network I am able to get an IP address from the Internal DHCP server but unable to access the network.
I've tried pinging the gateway's IP and I get no answer.
The Port-channel interface has the correct VLans and the vlans exist on all switches.
If anyone see an error there or might have an idea why this is not working I would appreciate the feedback.
Config follows below..
regards,
Gk

(Cisco Controller) >show running-config
802.11a cac voice tspec-inactivity-timeout ignore
802.11a cac voice stream-size 84000 max-streams 2
802.11b cac voice tspec-inactivity-timeout ignore
802.11b cac voice stream-size 84000 max-streams 2
location rssi-half-life tags 0
location rssi-half-life client 0
location rssi-half-life rogue-aps 0
location expiry tags 5
location expiry client 5
location expiry calibrating-client 5
location expiry rogue-aps 5
Cisco Public Safety is not allowed to set in thisdomain
ap syslog host global 255.255.255.255
auth-list ap-policy ssc enable
custom-web ext-webserver add 1 217.28.176.114
dhcp create-scope guestnetwork
dhcp address-pool guestnetwork 192.168.34.2 192.168.34.200
dhcp default-router guestnetwork 192.168.34.254
dhcp enable guestnetwork
dhcp dns-servers guestnetwork 212.30.200.200 212.30.200.199
dhcp network guestnetwork 192.168.34.0 255.255.255.0
local-auth method fast server-key *****
interface create guestnetwork 331
interface create guestnetwork-wired 332
interface address ap-manager 10.255.255.90 255.255.255.248 10.255.255.94
interface address dynamic-interface guestnetwork 192.168.34.1 255.255.255.0 192.168.34.254
interface address dynamic-interface guestnetwork-wired 192.168.35.1 255.255.255.0 192.168.35.254
interface address management 10.255.255.89 255.255.255.248 10.255.255.94
interface address service-port 10.60.4.200 255.255.255.0
interface address virtual 1.1.1.1
interface dhcp ap-manager primary 10.255.255.89
interface dhcp dynamic-interface guestnetwork primary 10.255.255.89
interface dhcp management primary 10.255.255.89
interface dhcp service-port disable
interface vlan ap-manager 226
interface vlan guestnetwork 331
interface vlan guestnetwork-wired 332
interface vlan management 226
interface port ap-manager 29
interface port guestnetwork 29
interface port guestnetwork-wired 29
interface port management 29
lag enable
load-balancing window 5
mesh security eap
mgmtuser add root **** read-write
mobility group domain XXXXXXX
mobility symmetric-tunneling enable
network otap-mode disable
network rf-network-name XXXXXXX
radius acct add 1 XXXXXXX 1813 ascii ****
radius auth add 1 XXXXXXX 1812 ascii ****
radius auth management 1 disable
spanningtree port mode off 1
spanningtree port mode off 2
sysname XXXXXXX
time ntp interval 3600
time ntp server 1 XXXXXXX
wlan create 1 hotspot hotspot
guest-lan create 1 hotspot-wired
wlan interface 1 guestnetwork
guest-lan interface 1 guestnetwork
wlan custom-web webauth-type external 1
wlan custom-web ext-webauth-url https://XXXXXXX
wlan session-timeout 1 disable
wlan wmm allow 1
wlan wmm allow 18
wlan security wpa disable 1
wlan security wpa disable 18
wlan radius_server auth add 1 1
wlan radius_server acct add 1 1
guest-lan radius_server auth add 1 1
guest-lan radius_server acct add 1 1
wlan dhcp_server 1 0.0.0.0 required required
wlan enable 1
guest-lan enable 1

Similar Messages

Wired guest access with 5508

Hi
I have setup wireless guest access for a customer with a single 5508 and web authentication no problem at all. He then wanted to test wired guest access. The 5508 is currently connected to a single 3560 switch. The wired clients get a DHCP address OK but cannot reslove DNS and thus don't get redirected to teh guest login portal. I have even tried turning of all L3 security to no avail. The setup is as follows
VLAN 101 access points and 5508 management interface
VLAN 102 wired guest access dynamic ingress (L2 config only no SVI on 3560)
VLAN 103 wireless guest dynamic egress nterface L3 network with SVI on switch
VLAN 104 wired guest dynamic egress interface L3 network with SVI on switch
There are two DHCP pools setup on the WLC one for the VLAN 103 and one for the VLAN 104 subnets.
The internet router is also connected to the 3560 on a sepearte VLAN with an SVI. the 3560 has a default route to teh internet router and teh DHCP pools give the DHCP clients a default gateway of the IP address of dynamic interface 103 or 104. The Internet routre can ping the WLC on both these addresses.
LAG is enabled on teh WLC and VLANs 101-104 are trunked to it from the 3560.
I even tried making the wired guest egress interface the same one as for wireless. The wired clientys now got an IP address on the wireless range but still couldnt pass any traffic. It's like the intrenal bridging on teh WLC between VALN 102 and 104 (or 103) is broken. Tried both the lates 6.x and 7.x software on the WLC. Any ideas ? All the problems I can find with this seem to relate to not gettingas far as a DHCP address but that works fine.
Thanks
Pat

Hi
Yes got it resolved. It turns out that the connection from the wired guest access port to the WLC must be L2. That is the switch that the wired guest acces sport is connected and WLC are connected to must be L2 only. We were using a single switch to do the testing and it was also doing the routing for the test LAN. Even though there was no L3 VLAN interface configured for the VLAN that the guest access port was on for some reason this breaks it. Absolu Didnt have chance to work out the exact limitations of this as we simply made the switch L2 only and configured an 802.1Q trunk to the Internet router and made subinterfaces on the router for the wired and wireless egress ports and it worked then. No config change was needed on the WLC at all.
The only thing I can think of is that it's something about the way the WLC joins the wired guest access ingress VLAn and egress VLAN. The WLC isn't a reall router it says so in the documentation. I think the packet coming from the wired access port is being bridged to the egress VLAn not routed and this is what screws it up (remeber with a router the source and destination MAC addresses would be changed with a bridge they aren't). Got to be something along those lines. If you have a bigger newtork with a guest anchor WLC handling this function you dont run into this as the traffic is coming over an EOIP tunnle from the remote WLC so the switch with the guest anchor WLC doesnt see the MAC address of the wired guest PC.

Unable to access website using home network but able to access using school network.

Hi, I'm currently on a MacBook Pro running OS X Mountain Lion and Safari v6.0.4.
As per the title, I'm unable to access particular websites, namely abduzeedo.com and fromupnorth.com, using my home network but when I try to access using my school network, I can access it freely.
The error message I get is: "Safari can't open the page [website] because the server where this page is located isn't responding"
I've tried clearing my cache, resetting my IP, deleting the library file (or whatever it was that some people suggested in forums) but it still doesn't work ):
Any suggestions?

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your personal files or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, or by a peripheral device.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards. Boot in safe mode and log in to the account with the problem. Note: If FileVault is enabled, or if a firmware password is set, or if the boot volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to boot and run than normal, and some things won’t work at all, including Wi-Fi on certain iMacs. The next normal boot may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, reboot as usual (i.e., not in safe mode) and verify that you still have the problem. Post the results of steps 1 and 2.

Unable to access shared files over network after period of time.

First off, I don't think that this issue is related to our router, but I have been searching for a fix and can not find one. We have a WRT54GS. Now, on to our issue:
At my work, we have a small network with computers sharing files between the others. I have attached a network diagram to help explain this better.
Our Win7 machine is our main computer that shares an external hard drive with much information that the other computers need to access. What we have noticed is either after a sleep, or even a period of time of say, 2 hours, those files are no longer able to be accessed. The Win7 machine is still sharing them, but the WinXP machines are unable to access them anymore and my Mac can see the computer is unable to connect to the folders. I have gone and attempted to get some help over at Microsofts site but that was a fail. Here is the link to the forum post there. http://social.answers.microsoft.com/Forums/en-US/w7network/thread/f0a2e8d6-f75a-41d7-a280-c6f3adbffa...
A member there gave me this:
The Network connection is probably not resuming after sleep.
First try this, http://www.ezlan.net/Win7/power_save_win7.jpg
It is in the Network Connection Properties under the Network card configuration.
If it already checked this way, or does not work after checking, the Network card has to be taken out of the computer's Power Saving loop, and stay on all the time.
Otherwise, Updating the Card with the latest OEM drivers (downloaded from the computer's support site) might help too.
On a rare occasions, some cards might be "Quirky" in this regards and need to be replaced.
--I would like to add that this DOESN'T ONLY happen after sleep, it also happens after a time of being used.
I attempted those and no luck. This problem is still occurring and the only way we can fix it is by restarting the Win7 machine. But even if it is being used, we have no idea when those files are unable to be accessed.
*I will add that the Win7 machine is still able to access the other computers when this problem occurs if that helps.
**The Win7 machine is a Dell T3500 running Windows 7 64bit. I can provide specific hardware if needed. The drivers are all up to date as of yesterday.
***So upon looking in the Windows XP machine, both of the folders from the Win7 machine disappear once this problem occurs in the My Network Places folder. And one folder is on the internal drive, one is on external. The computers are in this situation now where I am unable to access them. The Win7 machine can read and write from the other computers, but the other computers can even see the Win7 Machine.
****All the connections are wired and are not using the wireless.
Thanks for any help that anyone may have for me!
Steve
Network Map > http://scubasblog.com/network.jpg
Dell Support Forum with same issue I posted >> http://en.community.dell.com/support-forums/network-internet-wireless/f/3324/p/19337620/19716797.asp...

It sounds like there is incompatibility issue with XP and Win7. To isolate this, do you have another Win7 machine? Try to add it to the network and check if the shared drives are accessible after sleep. If you don't have another computer, try virtual machine and create a Win7 system.
Update your LAN card driver from the manufacturer's site. Don't use the driver from windows update.
Lastly, does this happen to your XP machines? Like, one of the XP machine sharing a folder and falls asleep. When it wakes up, does Win7 machine can still access the shared folder?

Anyone seen strange behavior with wired guest access on WLAN Controller?

Cisco Doc ID 99470 spells out how to deploy wired guest access over wireless LAN Controllers.
That said, everything has been up and working for almost a year. Guest wireless uses anchor controller in DMZ - no issues.
Recently configured two wired ports for wired guest networking. The desktops get the correct IP address via DHCP. A wireless client (on the table right next to the wired clients) on the guest wireless gets an IP address as expected as well.
Open a continuous ping to the gateway 172.16.16.1 on all three machines.
The two desktops will ping for a few minutes and then stop for 30 seconds or longer. Wireless client will keep its connection. (you might think it would be the other way around)
I understand there is a 65,535 second inactivity timeout, but I am only sitting here for minutes, not 18 hours when this happens.
On the wired desktops, you have to bring up a browser and log back in just as you do on a wireless client ever few minutes. After debugging the client, I found a "failed to find scb" message in the output.
The other trick here is that the wired clients are miles away from where I can actually get on the CLI of the controller. This makes it difficult to run a debug and bring up a browser since I am not local to the machines when running debugs.
Has anyone ever see this behavior? Has anyone see the "failed to find scb" message?
Thanks in advance!
Succ
essfully plumbed mobile rule (ACL ID 255)
*pemReceiveTask: Dec 30 11:33:15.735: 00:25:b3:ce:cb:ef 0.0.0.0 tokenID = 5
*pemReceiveTask: Dec 30 11:33:15.735: 00:25:b3:ce:cb:ef Set bi-dir guest tunn
el for 00:25:b3:ce:cb:ef as in Export Foreign role
*pemReceiveTask: Dec 30 11:33:15.735: 00:25:b3:ce:cb:ef 0.0.0.0 Added NPU ent
ry of type 1, dtlFlags 0x4
*spamReceiveTask: Dec 30 11:34:54.569: CCKM: Send CCKM cache entry
FP08:(33207772)[cmdSendNodeInfo:3787]failed to find scb 0023.2422.c6eb
*mmListen: Dec 30 11:35:58.539: 00:25:b3:ce:cb:ef Scheduling deletion of Mobi
le Station: (callerId: 73) in 1 seconds
*mmListen: Dec 30 11:35:59.471: 00:25:b3:ce:cb:ef Scheduling deletion of Mobi

I found it in the document
B.1 How Logout Works
The WebGate logs a user out when it receives a URL containing "logout." (including the "."), with the exceptions of logout.gif and logout.jpg, for example, logout.html or logout.pl. When the WebGate receives a URL with this string, the value of the ObSSOCookie is set to "logout."
The Access System sets an obSSOCookie for each user or application that accesses a resource protected by a WebGate. The obSSOCookie enables users to access resources that are protected by the Access System that have the same or a lower authentication level. Removing the ObSSOcookie causes the WebGate to log the user out and requires the user to re-authenticate the next time he or she requests a resource that is protected by the Access System.
Well, I havn't got that far in the document:)
Thanks a lot for your help.
-Wei

Wired guest access on WLC 4400 with SW 7.0.240.0

Hello,
after we upgrade our Wlan-controller 4400 from software 7.0.116.0 to 7.0.240.0
wired guest access don't work anymore.
All other things works fine, incl. WLAN guest access!
When we try wired guest access, we get the web-authentication page and can log in.
On the controller we can see that the Policy Manager State changes from WEBAUTH_REQD
to RUN.
But then there is no access to the internet.
We tried also SW 7.0.250.0, same problem!
Log Analysis on the WCS:
Time :03/12/2014 14:21:23 MEZ Severity :INFO Controller IP :10.101.200.11 Message :The WLAN to which client is connecting does not require 802 1x authentication.
Time :03/12/2014 14:21:23 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client does not have an IP address yet.
Time :03/12/2014 14:21:23 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client L3 authentication is required
Time :03/12/2014 14:21:23 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client Moved to DHCP Required State.
Time :03/12/2014 14:21:26 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Mobility role update request. from Unassociated to Local Peer = 0.0.0.0, Old Anchor = 0.0.0.0, New Anchor = 10.101.200.11
Time :03/12/2014 14:21:26 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Mobility role changed. State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
Time :03/12/2014 14:21:26 MEZ Severity :INFO Controller IP :10.101.200.11 Message :DHCP successful.
Time :03/12/2014 14:21:26 MEZ Severity :ERROR Controller IP :10.101.200.11 Message :Client got an IP address successfully and the WLAN requires Web Auth or Web Auth pass through.
Time :03/12/2014 14:21:26 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client IP address is assigned.
Time :03/12/2014 14:22:01 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Webauth user logged in to the network. manni
Time :03/12/2014 14:22:01 MEZ Severity :INFO Controller IP :10.101.200.11 Message :AAA response message sent.
Time :03/12/2014 14:22:01 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client has completed Web Auth successfully.
Time :03/12/2014 14:22:01 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client has completed Web Auth successfully.
Trying http://www.google.de .... doesnt work. No Log Entries. Next entries while logging out.
Time :03/12/2014 14:36:20 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Web auth is being triggered again.
Time :03/12/2014 14:36:20 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client L2 authentication has been completed successfully.
Time :03/12/2014 14:36:20 MEZ Severity :INFO Controller IP :10.101.200.11 Message :Client Moved to DHCP Required State.
Time :03/12/2014 14:36:20 MEZ Severity :INFO Controller IP :10.101.200.11 Message :WebAuth user Logged out from network.
Has someone a idea how to solve this problem?
Regards
Manfred

Hi
Yes got it resolved. It turns out that the connection from the wired guest access port to the WLC must be L2. That is the switch that the wired guest acces sport is connected and WLC are connected to must be L2 only. We were using a single switch to do the testing and it was also doing the routing for the test LAN. Even though there was no L3 VLAN interface configured for the VLAN that the guest access port was on for some reason this breaks it. Absolu Didnt have chance to work out the exact limitations of this as we simply made the switch L2 only and configured an 802.1Q trunk to the Internet router and made subinterfaces on the router for the wired and wireless egress ports and it worked then. No config change was needed on the WLC at all.
The only thing I can think of is that it's something about the way the WLC joins the wired guest access ingress VLAn and egress VLAN. The WLC isn't a reall router it says so in the documentation. I think the packet coming from the wired access port is being bridged to the egress VLAn not routed and this is what screws it up (remeber with a router the source and destination MAC addresses would be changed with a bridge they aren't). Got to be something along those lines. If you have a bigger newtork with a guest anchor WLC handling this function you dont run into this as the traffic is coming over an EOIP tunnle from the remote WLC so the switch with the guest anchor WLC doesnt see the MAC address of the wired guest PC.

Ask the Experts: Wired Guest Access

Sharath K.P.
Welcome to the Cisco Support Community Ask the Expert conversation. This is an opportunity to learn and ask questions on wired guest access with expert Sharath K.P. Wired guest access enables guest users to connect to the guest access network from a wired Ethernet connection designated and configured for guest access. Sharath K.P. is a Customer Support Engineer specialized in wireless and switching technologies at the Technical Assistance Center in Cisco Bangalore. He has been troubleshooting wireless and switching networks and management tools since 2009. Sharath has a bachelor's degree in Electrical Electronics Engineering from P.E.S College of Engineering (PESCE), VTU at Belgaum. India. He holds CCNP certifications in R&S and Wireless.
Remember to use the rating system to let Sharath know if you have received an adequate response.
Sharath might not be able to answer each question due to the volume expected during this event.
Remember that you can continue the conversation on the Wireless and Mobility sub-community discussion forum shortly after the event. This event lasts
through January 27, 2012. Visit this forum often to view responses to your questions and the questions
of other community members.

Hi Daniel ,
Wonderful observation and great question .
Yes, we dont find any recommendation or inputs in Cisco Docs on scenarios where we have multiple foriegn WLC's present .When we go through the Cisco Doc available for Wired Guest Access
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a00808ed026.shtml
Two separate solutions are available to the customers:
A single WLAN controller (VLAN Translation mode) - the access switch trunks the wired guest traffic in the guest VLAN to the WLAN controller that provides the wired guest access solution. This controller carries out the VLAN translation from the ingress wired guest VLAN to the egress VLAN.
Two WLAN controllers (Auto Anchor mode) - the access switch trunks the wired guest traffic to a local WLAN controller (the controller nearest to the access switch). This local WLAN controller anchors the client onto a DMZ Anchor WLAN controller that is configured for wired and wireless guest access. After a successful handoff of the client to the DMZ anchor controller, the DHCP IP address assignment, authentication of the client, etc. are handled in the DMZ WLC. After it completes the authentication, the client is allowed to send/receive traffic.
So as per Cisco best pratices using multiple foreign controllers for the same wired guest VLAN is not supported and the results will be unpredictable
I do understand the confusion regarding such scenario's as this( Multiple foriegn WLC's) is a very general setup which customer would like to deploy .
We have already opened a bug for the same (Little late though )
BUG ID :CSCtw44999
The WLC Config Guide should clarify our support for redundancy options for wired guest
Symptom:
Do not trunk a wired guest VLAN to multiple foreign controllers. This is not supported, and will
generate unpredictable results.
Some of the other tthat changes we will be making as a part of doc correction would be
http://www.cisco.com/en/US/docs/wireless/controller/7.0MR1/configuration/guide/cg_user_accts.html#wp1066125
1. The WiSM2 needs to be added as a supported controller. (Not sure about the 7500, check with PM)
2. Where it says "Do not attempt to trunk a guest VLAN on the Catalyst 3750G ...", this should read:
"Do not trunk a wired guest VLAN to multiple foreign controllers. This is not supported, and will
generate unpredictable results."
3. Add at least a line mentioning support for multiple anchors for a guest wired LAN.
Now if you already have such deployments , ther criteria would be that nearest WLC on the broadcast domain (Layer 2) would respond to the client associtation request .
Cisco Controller) >Tue Sep 11 13:27:42 2007: 00:0d:60:5e:ca:62 Adding mobile on Wired Guest 00:00:00:00:00:00(0)
Tue Sep 11 13:27:42 2007: 00:0d:60:5e:ca:62 apfHandleWiredGuestMobileStation (apf_wired_guest.c:121) Changing state for mobile
00:0d:60:5e:ca:62 on AP 00:00:00: 00:00:00 from Idle to Associated .
I hope the above explanation could clarify your doubts to certain extent and also keep you
informed on Cisco's roadmap on this feature .
Regards ,
Sharath K.P.

2106 and Wired Guest Access

Hi,
It seems that the 2100 models do not support wired guest access. I wondered if the following work around might work?
We are using a 2106 with a wireless guest network anchored to a 5508.
Would it be possible to configure an Autonomous AP in WGB mode and configure it to connect to the visitor wlan?
Would wired clients then be able to connect through the autonmous AP and use web authentication?
Cheers

I opened a TAC with Cisco.
Here was the repsonse.
Unfortunately this is not a supported feature , please have a look at the following
· These lightweight features are supported for use with a workgroup bridge:
– Guest N+1 redundancy
– Local EAP
· These lightweight features are not supported for use with a workgroup bridge:
– Cisco Centralized Key Management (CCKM)
– Hybrid REAP
– Idle timeout
– Web authentication
Note If a workgroup bridge associates to a web-authentication WLAN, the workgroup bridge is added to the exclusion list, and all of the workgroup bridge wired clients are deleted.
So it is not possible. Just thought I'd share this in case anyone else came across the same issue.

Wired guest access support on SRE G2

I have been trying to find info on support for wired guest access on SRE wireless module. Is it supported? Also, does 2100 wlc support it? I am running into sizing issues as I am seeing in documentation that it is supported on WiSM, 4400 (end of life), 5500, and 3750G (end of life). So, Am I only left with 5500? These are bunch of branch offices and do not know if having 5500 in each site is financially feasible. There is a requirement to have all these networks separate so we cannnot share controllers. Thank you in advance.

It's more like "all WLCs support what is in config guide unless stated otherwise".
http://www.cisco.com/en/US/prod/collateral/wireless/ps6302/ps8322/ps7206/ps7221/product_data_sheet0900aecd805aaab9.html
the Cisco 2100 Series enables administrators to securely manage WLANs and mobility services, such as enhanced security, voice, guest access, and location services."
It says nowhere that the SRE can't do wired/wireless. So it does the same as other WLCs from that point of view

Unable to Access Web Site (with same name) outside of Local Network

Hi everyone,
I have my web site (and some other services) hosted outside of my network by my hosting provider, but handle all other items using OS X Server on my network (i.e. Wiki and so forth).
The problem is now that I am unable to access my website at www.mydomain.com from within the network. I have external DNS set up for www.mydomain.com to point to my website, while mydomain.com points to my OS X Server (static IP address). Internally in OS X Server's DNS settings this used to work when I had www.mydomain.com resolving to the IP address of my web host, in addition to the default domain settings that OS X had set up. For some reason this is no longer working, and I am unable to figure out why.
Using latest version of OS X Server 3.0.2.
Any help is greatly appreciated. Thanks!
Update: this ended up being a redirect issue on the web host. I added another subdomain that was hosted externally, and it worked fine. For some reason my web host is redirecting www.mydomain.com to domain.com.

I am in Texas and cannot get to that site either. Do you know for sure the site is up and working? It could just be down (for days, a site I support was down for almost 4 full days a few weeks ago due to a virus problem).
This may (again, may) be your problem: I see you have a173.48.x.x (you really should x-out the last two octets of your IP address for privacy reasons), I am on a 173.74.x.x address; I know some people have had problems with getting to some sites now that they have a 173.x.x.x address. I think Verizon obtained addresses in that range and some of the addresses apparently previously belonged to spammers or some malicious folks.Some sites (web sites, intermeidate routers, etc.) blocked those addresses, and may not have updated their filters to remove the block on those addresses because they don't know that Verizon now owns them. If this is the problem, eventually those filters will get updated and you will be able to access the site, but this could be a fairly long time.
If you know how to contact that site I suggest you email them about the problem. You can also try turning off your router overnight and when you turn it back on the next day you may find that you have a different address (one that doesn't start with 173) that will allow you to get to the site.
I don't think there is much Verizon can do to help, it is not their site that is blocking your address (at least I don't think it is).
Hope this helps.
Justin
Verizon FiOS TV, Internet, and phone
IMG 1.6.2, Build 08.58
Keller, TX 76248

How do I use Airport Extreme to create wired access point on wireless network?

Bit of an odd situation. I just went from cable to DSL at home and the modem moved from right by my computer to upstairs.
Trouble is, there's no real easy way to get a cable from the modem upstairs to my X-box (sans wireless connector) downstairs.
I could buy the wireless adaptor for the X-Box, but I was hoping I wouldn't have to spend any more money.
I have my airport extreme, and I was hoping I could use it to create a wired access point on the network, recieving the signal from the wireless modem upstairs and allowing me to plug in the X-Box.
Is this possible? If so, how? I've been through the config panel about a dozen times, but can't figure out what combination to set up.
Thanks.

Will it work if I use the express to create the network?
Yes, providing that you have an 802.11n version of the AirPort Express and the Express has been configured to "Allow this network to be extended".
Then, the AirPort Extreme can be configured to "extend" the Express network. When you do this, the AirPort Extreme will provide more wireless coverage and the LAN Ethernet ports are enabled, so you can connect an Ethernet device.
This will not be a "normal" Ethernet connection. It will only work as well as the wireless "hop" between the Express and Extreme allow.
For best results and performance, a wired connection through the hole in the wall is always best. If you decide to do this, you will need the "new" AirPort Express with both a WAN and LAN port on the device. But, you could try wireless first to see if it will meet your goals before you reach for the tools.

Unable to access my other macs in the airport network

Since I have installed Leopard 10.5.1 I am unable to access my other MACs in my airpot network for file sharing. Interesting that I can accesss my older IMAC which has TIGER 10.4.11 installed. This bug is new since I updated to 10.5.1. Its funny but "screensharing" on the other hand is working.
(I checked all possibilities in the firewall setting. (File sharing) is allowed on all MACs.
Anyone with a solution or having the same problem
Tony

Ok, they didn't post the link to my screen cap.
Here is the link to the screen cap of my problem in FireFo:.
http://i88.photobucket.com/albums/k196/ajax6677/more.png
Here is how it looks when loaded properly in IE:
http://i88.photobucket.com/albums/k196/ajax6677/more2.png
They are also attached below/

Unable to access internal networks over Remote acces VPN

Hi,
I have set up a Remote access VPN from Home to Cisco ASA 5512-X.
I am able to connect successfully and even getting a valid IP address from VPN pool 172.21.3.1-. However I am unable to access any of the internal resources.
Internal Network: 172.20.0.0 255.255.0.0
Please if someone can help identifying the issue.
Below is the running config:-
Result of the command: "sh run"
: Saved
ASA Version 9.1(1)
hostname ASA
domain-name M8fl.com
enable password Aoz9GlxLLvkWrTUy encrypted
passwd Gc1jA6zbgOsj63RW encrypted
names
ip local pool vpnclients 172.21.3.1-172.21.3.20 mask 255.255.0.0
ip local pool test 172.21.3.21-172.21.3.40 mask 255.255.255.0
interface GigabitEthernet0/1
nameif inside
security-level 100
ip address 172.20.254.250 255.255.0.0
interface GigabitEthernet0/2
description vodafone 100mb internet 195.11.180.40_29
speed 100
duplex full
nameif outside1
security-level 1
ip address 195.11.180.42 255.255.255.248
interface GigabitEthernet0/3
description Voice
nameif Voice
security-level 80
ip address 192.168.2.1 255.255.255.252
interface GigabitEthernet0/4
shutdown
no nameif
no security-level
no ip address
interface GigabitEthernet0/5
shutdown
no nameif
no security-level
no ip address
interface Management0/0
management-only
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
boot system disk0:/asa911-smp-k8.bin
ftp mode passive
clock timezone GMT 0
dns domain-lookup inside
dns domain-lookup outside1
dns domain-lookup management
dns server-group DefaultDNS
name-server 10.0.0.4
name-server 172.20.0.100
domain-name M8fl.com
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object network VLAN1
subnet 172.20.0.0 255.255.0.0
object network NETWORK_OBJ_172.20.3.0_27
subnet 172.21.3.0 255.255.255.224
object network Voice_Net
subnet 172.21.20.0 255.255.255.0
object network PBX_Internal
host 192.168.2.2
description PBX Internal
object network Voice_External
host 195.11.180.43
description For PBX
object network Raith_Remote_Network
subnet 192.168.20.0 255.255.255.0
description Raith Remote Network
object network NETWORK_OBJ_172.21.3.0_27
subnet 172.21.3.0 255.255.255.224
object network NETWORK_OBJ_172.21.3.0_26
subnet 172.21.3.0 255.255.255.192
object-group network azure-networks
network-object 10.0.0.0 255.0.0.0
object-group network onprem-networks
network-object 172.20.0.0 255.255.0.0
object-group protocol TCPUDP
protocol-object udp
protocol-object tcp
object-group service test_PPTP
service-object ip
service-object tcp destination eq pptp
access-list azure-vpn-acl extended permit ip object-group onprem-networks object-group azure-networks
access-list outside_access_in extended permit ip object-group azure-networks object-group onprem-networks
access-list outside_access_in extended permit icmp any any
access-list outside_access_in extended permit ip any any
access-list inside_access_in extended permit ip any any log disable
access-list inside_access_in_1 extended permit ip object-group onprem-networks object-group azure-networks
access-list inside_access_in_1 extended permit ip any object Voice_Net log debugging
access-list inside_access_in_1 extended permit ip any any
access-list outside_access_in_1 extended permit ip object-group azure-networks object-group onprem-networks
access-list outside_access_in_1 extended permit icmp any any
access-list outside_access_in_1 extended permit ip any any inactive
access-list Voice_access_in extended permit ip any any log debugging
access-list outside_cryptomap extended permit ip object-group onprem-networks object Raith_Remote_Network
pager lines 24
logging enable
logging buffer-size 40000
logging buffered notifications
logging asdm debugging
mtu outside 1500
mtu inside 1500
mtu outside1 1500
mtu Voice 1500
mtu management 1500
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-66114.bin
no asdm history enable
arp timeout 14400
no arp permit-nonconnected
nat (inside,outside1) source static onprem-networks onprem-networks destination static azure-networks azure-networks
nat (inside,outside1) source dynamic VLAN1 interface
nat (inside,Voice) source static VLAN1 VLAN1 destination static Voice_Net Voice_Net no-proxy-arp route-lookup
nat (Voice,outside1) source static PBX_Internal Voice_External
nat (inside,outside) source static onprem-networks onprem-networks destination static Raith_Remote_Network Raith_Remote_Network no-proxy-arp route-lookup
nat (inside,outside1) source static any any destination static NETWORK_OBJ_172.21.3.0_27 NETWORK_OBJ_172.21.3.0_27 no-proxy-arp route-lookup
nat (inside,outside1) source static any any destination static NETWORK_OBJ_172.21.3.0_26 NETWORK_OBJ_172.21.3.0_26 no-proxy-arp route-lookup
access-group outside_access_in in interface outside
access-group inside_access_in_1 in interface inside
access-group outside_access_in_1 in interface outside1
access-group Voice_access_in in interface Voice
route outside1 0.0.0.0 0.0.0.0 195.11.180.41 10
route inside 172.21.20.0 255.255.255.0 172.20.20.253 1
timeout xlate 3:00:00
timeout pat-xlate 0:00:30
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
user-identity default-domain LOCAL
aaa authentication ssh console LOCAL
aaa authentication http console LOCAL
http server enable 444
http 192.168.1.0 255.255.255.0 management
http 172.20.0.0 255.255.0.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
sysopt connection tcpmss 1350
sysopt noproxyarp outside
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set azure-ipsec-proposal-set esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-3DES-SHA mode transport
crypto ipsec ikev2 ipsec-proposal DES
protocol esp encryption des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal 3DES
protocol esp encryption 3des
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES
protocol esp encryption aes
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES192
protocol esp encryption aes-192
protocol esp integrity sha-1 md5
crypto ipsec ikev2 ipsec-proposal AES256
protocol esp encryption aes-256
protocol esp integrity sha-1 md5
crypto ipsec security-association lifetime seconds 3600
crypto ipsec security-association lifetime kilobytes 102400000
crypto ipsec security-association pmtu-aging infinite
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime seconds 28800
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set security-association lifetime kilobytes 4608000
crypto map outside_map interface outside
crypto ca trustpoint ASDM_TrustPoint0
enrollment terminal
subject-name CN=ASA
crl configure
crypto ca trustpool policy
crypto ikev2 policy 1
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 10
encryption aes-256
integrity sha
group 5 2
prf sha
lifetime seconds 28800
crypto ikev2 policy 20
encryption aes
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 30
encryption 3des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 policy 40
encryption des
integrity sha
group 5 2
prf sha
lifetime seconds 86400
crypto ikev2 enable outside
crypto ikev1 enable outside
crypto ikev1 enable outside1
crypto ikev1 policy 10
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 28800
crypto ikev1 policy 20
authentication rsa-sig
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 30
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 40
authentication crack
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 50
authentication rsa-sig
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 60
authentication pre-share
encryption aes-192
hash sha
group 2
lifetime 86400
crypto ikev1 policy 70
authentication crack
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 80
authentication rsa-sig
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 90
authentication pre-share
encryption aes
hash sha
group 2
lifetime 86400
crypto ikev1 policy 100
authentication crack
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 110
authentication rsa-sig
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 120
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 130
authentication crack
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 140
authentication rsa-sig
encryption des
hash sha
group 2
lifetime 86400
crypto ikev1 policy 150
authentication pre-share
encryption des
hash sha
group 2
lifetime 86400
telnet 172.20.0.0 255.255.0.0 inside
telnet timeout 5
ssh 172.20.0.0 255.255.0.0 inside
ssh timeout 5
ssh version 2
console timeout 0
dhcpd address 172.20.2.1-172.20.2.254 inside
dhcpd dns 10.0.0.4 172.20.0.100 interface inside
dhcpd enable inside
dhcpd dns 172.21.20.254 interface Voice
dhcpd address 192.168.1.2-192.168.1.254 management
dhcpd enable management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
tftp-server inside 172.20.2.34 /tftp
webvpn
enable outside1
anyconnect image disk0:/anyconnect-win-2.5.2014-k9.pkg 1
anyconnect image disk0:/anyconnect-linux-2.5.2014-k9.pkg 2
anyconnect image disk0:/anyconnect-macosx-i386-2.5.2014-k9.pkg 3
anyconnect enable
tunnel-group-list enable
internal-password enable
group-policy DefaultRAGroup_2 internal
group-policy DefaultRAGroup_2 attributes
dns-server value 10.0.0.4 172.20.0.100
vpn-tunnel-protocol l2tp-ipsec
default-domain value
group-policy DefaultRAGroup_3 internal
group-policy DefaultRAGroup_3 attributes
dns-server value 10.0.0.4 172.20.0.100
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 10.0.0.4 172.20.0.100
vpn-tunnel-protocol l2tp-ipsec
default-domain value
group-policy DefaultRAGroup_1 internal
group-policy DefaultRAGroup_1 attributes
dns-server value 10.0.0.4 172.20.0.100
vpn-tunnel-protocol l2tp-ipsec
default-domain value
group-policy DfltGrpPolicy attributes
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
group-policy RA_VPN internal
group-policy RA_VPN attributes
dns-server value 8.8.8.8 4.2.2.2
vpn-tunnel-protocol ikev1
default-domain value
group-policy "GroupPolicy_Anyconnect _profile" internal
group-policy "GroupPolicy_Anyconnect _profile" attributes
wins-server none
dns-server value 8.8.8.8
vpn-tunnel-protocol ssl-client ssl-clientless
default-domain none
webvpn
file-browsing enable
group-policy GroupPolicy_89.241.208.14 internal
group-policy GroupPolicy_89.241.208.14 attributes
vpn-tunnel-protocol ikev1
username test2 password encrypted privilege 15
username test1 password nt-encrypted privilege 0
username test1 attributes
vpn-group-policy DefaultRAGroup_2
username test password encrypted privilege 15
username test attributes
vpn-group-policy DefaultRAGroup_1
username EdwardM password encrypted privilege 15
username vpntest password encrypted privilege 0
username vpntest attributes
vpn-group-policy RA_VPN
username vpntest3 password nt-encrypted privilege 15
username vpntest3 attributes
service-type remote-access
username rhunton password encrypted privilege 15
username rhunton attributes
service-type admin
username e.melaugh password encrypted privilege 15
username netx password encrypted privilege 15
username netx attributes
service-type remote-access
username colin password encrypted privilege 15
username colin attributes
service-type remote-access
tunnel-group DefaultL2LGroup ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group DefaultRAGroup general-attributes
address-pool vpnclients
default-group-policy DefaultRAGroup_3
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
isakmp keepalive disable
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
authentication ms-chap-v2
tunnel-group "Anyconnect _profile" type remote-access
tunnel-group "Anyconnect _profile" general-attributes
address-pool vpnclients
default-group-policy "GroupPolicy_Anyconnect _profile"
tunnel-group "Anyconnect _profile" webvpn-attributes
group-alias "Anyconnect _profile" enable
tunnel-group 137.117.215.177 type ipsec-l2l
tunnel-group 137.117.215.177 ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
isakmp keepalive disable
tunnel-group 89.241.208.14 type ipsec-l2l
tunnel-group 89.241.208.14 general-attributes
default-group-policy GroupPolicy_89.241.208.14
tunnel-group 89.241.208.14 ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect pptp
policy-map type inspect ipsec-pass-thru Fairhurst
description to allow vpn to fairhurst network
parameters
esp
ah
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:f4185106b309478da7804dc22d2c1a85
: end

Hi,
You seem to have this nat (inside,outside1) source dynamic VLAN1 interface at line 2 which is causing the identity Nat/ Nat exempt to fail.
It is always good to use the packet tracer feature on the ASA to see what exactly is happening.
Try this
nat (inside,outside1) 1 source static VLAN1 VLAN1 destination static NETWORK_OBJ_172.21.3.0_27 NETWORK_OBJ_172.21.3.0_27 no-pr route-lo
Let me know how it goes for you.
Regards,
Nitish Emmanuel

Using the personal hotspot feature on the iPhone 5, I am able to connect to the internet. We also use Juniper NCP client to access our system remote. A VPN connection is created, but I am unable to access servers on our network. This works on iPhone 4.

Using the personal hotspot feature on the iPhone 5, I am able to connect to the internet. We also use Juniper NCP client to access our local system from a remote location. A VPN connection is created, but I am unable to access servers in our network. This same functionality works using my colleagues iPhone 4.
Both phones are running iOS 6.1.3. I tried to reset network settings, but still unable to ping servers in our network. This is a feature that our sales team relies heavily on when out of the office. Hoping someone has some suggestions on what is different between the 2 phones.

Hi,
Generally, this issue should be related with something called split tunneling, since you’re using a F5 vpn client, you need to look for something related to split tunneling in the F5 VPN client's documentations.
Here is an example, share it with you as a reference.
http://support.f5.com/kb/en-us/products/big-ip_apm/manuals/product/apm_config_10_2_0/apm_config_networkaccess.html
In addition, you can refer to the link below for more solution about this problem.
You Cannot Connect to the Internet After You Connect to a VPN Server
http://support.microsoft.com/kb/317025
NOTE
This
response contains a reference to a third party World Wide Web site. Microsoft is providing this information as a convenience to you.
Microsoft
does not control these sites and has not tested any software or information found on these sites.
Yolanda Zhu
TechNet Community Support

VPN connects but unable to access resources on remote network

HI,
I'm able to ping the ASA interface once the VPN is connected but unable to access any of the resources located on the remote network such as shares and computers. The cisco vpn client shows data being sent and recieved when I ping the interface on the ASA but it doesn't recieve any data when I attempt to ping or access other resources on the network.
ASA Version 8.2(5)
hostname HOST_NAME
domain-name default.domain.invalid
names
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
speed 10
duplex half
interface Ethernet0/4
speed 100
duplex full
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 10.10.8.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 12.x.x.x x.x.x.x
boot system disk0:/asa825-k8.bin
ftp mode passive
dns domain-lookup inside
dns domain-lookup outside
dns server-group DefaultDNS
name-server 10.10.8.2
domain-name default.domain.invalid
same-security-traffic permit intra-interface
object-group service Vipre tcp
port-object range 18082 18082
port-object range 18086 18086
object-group network town
network-object 192.168.0.0 255.255.0.0
access-list outside_20_cryptomap extended permit ip 10.10.8.0 255.255.255.0 192.168.0.0 255.255.252.0
access-list new extended permit ip host 192.168.0.1 any
access-list new extended permit ip any host 192.168.0.1
access-list outside_20_cryptomap_1 extended permit ip 10.10.8.0 255.255.255.0 192.168.0.0 255.255.252.0
access-list townoffice_splitTunnelAcl standard permit 10.10.8.0 255.255.255.0
access-list townremote_splitTunnelAcl standard permit 10.10.8.0 255.255.255.0
access-list outside_access_in extended permit tcp any interface outside object-group Vipre
access-list outside_access_in extended permit tcp any object-group Vipre interface inside object-group Vipre
access-list outside_access_in extended permit tcp any eq 3389 10.10.8.0 255.255.255.0 eq 3389
access-list test extended permit ip host 192.168.0.6 host 10.10.8.155
access-list test extended permit ip host 10.10.8.155 host 192.168.0.6
access-list test extended permit ip host 10.10.8.2 host 192.168.3.116
access-list test extended permit ip host 192.168.3.116 host 10.10.8.2
access-list test extended permit ip host 10.10.8.155 host 192.168.3.116
access-list bypass extended permit ip host 10.10.8.155 host 192.168.3.116
access-list bypass extended permit tcp 192.168.0.0 255.255.0.0 10.10.8.0 255.255.255.0
access-list bypass extended permit tcp 10.10.8.0 255.255.255.0 192.168.0.0 255.255.0.0
pager lines 24
logging enable
logging buffered debugging
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn 10.10.8.125-10.10.8.149 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-522.bin
no asdm history enable
arp timeout 14400
global (inside) 1 interface
global (outside) 1 interface
nat (inside) 1 192.168.0.0 255.255.0.0
nat (inside) 1 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 18082 10.10.8.2 18082 netmask 255.255.255.255
static (inside,outside) tcp interface 18086 10.10.8.2 18086 netmask 255.255.255.255
static (inside,outside) tcp interface 3389 10.10.8.2 3389 netmask 255.255.255.255
static (inside,inside) 192.168.0.0 192.168.0.0 netmask 255.255.0.0
static (inside,inside) 10.10.8.0 10.10.8.0 netmask 255.255.255.0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 12.70.119.65 1
route inside 192.168.0.0 255.255.0.0 10.10.8.250 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
aaa authentication ssh console LOCAL
aaa authentication telnet console LOCAL
http server enable
http outside
http outside
http inside
http outside
http inside
http outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
sysopt noproxyarp inside
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set pfs
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 40 set pfs
crypto dynamic-map outside_dyn_map 40 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 60 set pfs
crypto dynamic-map outside_dyn_map 60 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 80 set pfs
crypto dynamic-map outside_dyn_map 80 set transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 100 set pfs
crypto dynamic-map outside_dyn_map 100 set transform-set ESP-3DES-SHA
crypto map outside_map 20 match address outside_20_cryptomap_1
crypto map outside_map 20 set pfs
crypto map outside_map 20 set peer 69.87.150.118
crypto map outside_map 20 set transform-set ESP-3DES-SHA ESP-3DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp nat-traversal 30
telnet 10.10.8.0 255.255.255.0 inside
telnet timeout 5
ssh 63.161.207.0 255.255.255.0 outside
ssh timeout 5
console timeout 0
dhcpd dns 10.8.8.2
dhcpd address 10.10.8.150-10.10.8.200 inside
dhcpd dns 10.10.8.2 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy aaa internal
group-policy aaa attributes
dns-server value 10.10.8.2 4.2.2.2
vpn-tunnel-protocol IPSec
default-domain value domainname
group-policy bbb internal
group-policy bbb attributes
wins-server value 10.10.8.2
dns-server value 10.10.8.2
vpn-tunnel-protocol IPSec l2tp-ipsec
split-tunnel-policy tunnelall
split-tunnel-network-list value townoffice_splitTunnelAcl
default-domain value domainname.local
group-policy townremote internal
group-policy townremote attributes
wins-server value 10.10.8.2
dns-server value 10.10.8.2 4.2.2.2
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value townremote_splitTunnelAcl
default-domain value domainanme
group-policy remote internal
group-policy remote attributes
wins-server value 10.10.8.2
dns-server value 10.10.8.2
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value townremote_splitTunnelAcl
default-domain value dksecurity.local
address-pools value vpn
username xxxx password . encrypted privilege 15
username xxxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy dksecurityremote
username xxxx password . encrypted privilege 15
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy dksecurityremote
username xxx password encrypted privilege 15
username xxx password encrypted privilege 15
username xxxx attributes
vpn-group-policy remote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy remote
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy remote
username xxxx password encrypted privilege 15
username xxx password encrypted privilege 15
username xxx attributes
vpn-group-policy remote
tunnel-group 69.87.150.118 type ipsec-l2l
tunnel-group 69.87.150.118 ipsec-attributes
pre-shared-key *****
tunnel-group remote type remote-access
tunnel-group remote general-attributes
address-pool vpn
default-group-policy townremote
tunnel-group townremote ipsec-attributes
pre-shared-key *****
isakmp keepalive disable
tunnel-group townremote type remote-access
tunnel-group townremote general-attributes
address-pool vpn
default-group-policy townremote
tunnel-group lansingremote ipsec-attributes
pre-shared-key *****
class-map tcp-bypass
match access-list bypass
class-map test
match access-list new
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
no dns-guard
no protocol-enforcement
no nat-rewrite
policy-map global_policy
class test
class inspection_default
policy-map tcp
class tcp-bypass
set connection random-sequence-number disable
set connection advanced-options tcp-state-bypass
service-policy global_policy global
service-policy tcp interface inside
prompt hostname context
call-home reporting anonymous prompt 2
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:c724d6744097760d94a7dcc79c39568a
: end

You need to change the VPN pool ip subnet to something other than the same ip range used on the inside interface.
Sent from Cisco Technical Support iPad App

Wired guest access - Unable to access network

Similar Messages

Maybe you are looking for