Wireless Device User Interface

Hello, I have developed JSPs and set up the Personalization Portal by creating a Service that runs off a Master Service.
I can access the JSP without any problem, but on my wireless device which uses Windows CE, all my <SimpleMenuItem> tags appear as links, and I would like them to be numbered so that the user on the device can use the keypad instead of the stylus pen. How can I do this?

The simplemenuitem tag renders as numbered links on mobile devices. Users can use the keypad to select thier desired item. However, on PDAs the links do not render as numbered because it is expected that they will use the stylus pen. Generally, devices with built-in keypads, you are able to use the keypad to select your item.
Regards,
Kalle
[email protected]

Similar Messages

Arch not detecting my wireless device

Here is what I gleaned from Windows Vista (I know, I know; but we have to live with reality):
Name NETGEAR
SSID NETGEAR
Network type Access Point
Device is Dell Wireless 1395 wlan mini-card
This is the response to ifconfig:
[billb@billbar ~]$ ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:1D:09:C9:05:83
inet addr:192.168.1.9 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::21d:9ff:fec9:583/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:9385 errors:0 dropped:0 overruns:0 frame:0
TX packets:8648 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:9222099 (8.7 Mb) TX bytes:1434222 (1.3 Mb)
Interrupt:21
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:28 errors:0 dropped:0 overruns:0 frame:0
TX packets:28 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1480 (1.4 Kb) TX bytes:1480 (1.4 Kb)
[billb@billbar ~]$
all of the "iw" utilities report - "no wireless device"
Guess I need a little handholding here.
Otherwise the Arch installtion is running beautifully off a cable connection, which comes from the Netgear wireless router.
Thanks for help.
Bill
Last edited by billbar (2009-12-10 09:39:06)

The ujpgrade from testing did change the wireless capablilities but we still have some problems.
Here is an extract from dmesg:
input: Broadcom Corp as /devices/pci0000:00/0000:00:13.3/usb5/5-2/5-2.2/5-2.2:1.0/input/input15
generic-usb 0003:0A5C:4502.0003: input,hidraw2: USB HID v1.11 Keyboard [Broadcom Corp] on usb-0000:00:13.3-2.2/input0
usb 5-2.3: new full speed USB device using ohci_hcd and address 5
usb 5-2.3: configuration #1 chosen from 1 choice
input: Broadcom Corp as /devices/pci0000:00/0000:00:13.3/usb5/5-2/5-2.3/5-2.3:1.0/input/input16
Then from a root terminal:
[root@billbar billb]# iwconfig
lo no wireless extensions.
eth0 no wireless extensions.
wlan0 IEEE 802.11bg Mode:Managed Access Point: Not-Associated
Tx-Power=0 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Encryption key:off
Power Management:off
[root@billbar billb]# ifconfig wlan0 up
SIOCSIFFLAGS: No such file or directory
[root@billbar billb]#
Then a request for root password from wicd:
Don't know how wicd gets started.
If I respond the program terminates with an error and disconnects my current eth0 connection.
Here are some extracts from my rc.conf
#eth0="eth0 192.168.0.2 netmask 255.255.255.0 broadcast 192.168.0.255"
eth0="dhcp"
INTERFACES=(eth0)
gateway="default gw 192.168.0.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
#NETWORKS=menu
DAEMONS=(syslog-ng hal network netfs crond alsa kdm)
The dialog and netcfg packages are in the OS. i have tried uncommenting NETWORKS=menu but no dialog appears during the boot.
I am currently connected with cable. Is that a conflict in enabling wireless.
The wireless network uses wpa encryption and connects in Windows Vista on this machine. It's a dual boot machine.

Question re: multiple wireless devices and the Duel Band Airport Extreme

I recently purchased the new duel-band Airport Extreme. Prior to that I had the single band Airport Extreme. I’m a bit confused about how it works and have spent a good bit of time trying to find the answers on the web, but nothing really addresses my specific question so I’m coming to the experts.
I have a number of wireless devices throughout my house… a couple of Roku boxes, two iPads, two iPods running Pandora, a MacBook and an older model Apple TV etc.
Both of the iPods are 802.11 G. The iPads can handle N.
One Roku is 802.11 G and the other can handle N.
I am confused about configuring the Airport Extreme. It’s my understanding that if I just go with the basic setup of creating a network and selecting Automatic for the Radio Mode and Channel that all of my devices will automatically connect to the most appropriate band for the best throughput for that particular device.
I have tried configuring the Airport Extreme as I mentioned above, as well as setting it up with the 5GHz Network Name field selected. I gave this a different name so I would be able to distinguish between the two networks when selecting one on my iPad. I will refer to the fist configuration as Setup A and the second (naming the 5 GHZ Network ) as Setup B.
When I use Setup A all of my devices show one available network to connect to. I select that network and all is well.
When I use Setup B the devices show two available networks, the original and the one I named on the 5GHz Network Name Filed.
My iPod’s ( 802.11 G ) only display the name of the first network, but my iPad’s show both, and I can select either. The signal strength on the 5GHz channel only dislplays two bars on the signal strength indicator icon, but the other network is full bars.
When I use Setup A, is my iPad, Roku and MacBook automatically selecting the 5GHz AND the N connection? How do I know that it’s not using the G band? Is it best to just go with the automatic settings and trust that I’m getting the best connections? How does it know weather to connect to the 2.4 GHz or 5 GHz. What determines that ?
Sorry for the rambling questions but the more I think about it the more confused I get about all of the possible combinations of connectivity possibilities.
I appreciate any attempts at making this a “teachable moment” for me :- )
Thanks !
Chuck
Message was edited by: ChuckLD

Welcome to the discussion area!
The signal strength on the 5GHz channel only dislplays two bars on the signal strength indicator icon, but the other network is full bars.
Not surprising, because the much higher frequency 5 GHz signals are absorbed much more quickly by any obstructions than 2.4 GHz signals. Everything is a trade off. In return for higher speeds, you must give up distance capability and penetration power with 5 GHz. It's not exactly true that you have to have a line-of-sight arrangement between the router and computer with 5 GHz, but many users are finding that to be the case for good, reliable performance.
How does it know weather to connect to the 2.4 GHz or 5 GHz. What determines that ?
The signal strength. If your computer is capable of connecting at both 2.4 GHz and 5 GHz, it will choose the band with the higher signal strength...assuming that both bands have the same network name. The only way you can "force" a device to connect to the 5 GHz band is set it up with a different name and point your computer to that specific network.
For most users, the way to go is setup both bands with the same wireless network name and let devices connect to the strongest signal automatically.

How can I use AirPlay from a wireless device while in 'Join a network' mode with an Ethernet client?

I just got the brand new Airport Express (simultaneous dual-band 802.11n) and I'm trying to set it up to join an existing working wireless network that I have in my house, and to drive my home stereo amplifier and have my desktop hooked up via the wired Ethernet port on the Airport Express. Here's how I set it up:
-Wireless mode is 'Join a wireless network'
-Wireless Network Name: <my home network>
--Allow Ethernet clients is checked
-Internet is configured via DHCP (it gets a valid DHCP lease and IP address on my subnet)
-AirPlay is enabled
-The audio out from the Airport Express is connected to my amplifier via an optical digital cable.
If I leave it set up just as described above, I can select the Airport device from iTunes on my MacBook Pro and play music directly to the speakers. Perfect.
The problem comes when I go to plug in my desktop to the wired Ethernet port on the Airport Express. As soon as I plug in the Ethernet, AirPlay stops working on the laptop. Even if iTunes is in the middle of playing a track, the track will stop when the Ethernet cable is plugged in (with a device on the other end). Doesn't matter which of the two Ethernet ports I use. My desktop is able to use the internet while plugged in to the Airport Express, but iTunes on the laptop is no longer able to connect to the Airport Express to use AirPlay.
I've found that if instead of plugging my desktop into the Airport Express's wired ethernet, I plug in the laptop, then iTunes on the laptop is able to use AirPlay -- but then no other devices on the network are able to use AirPlay.
It appears that as soon as I plug in a wired Ethernet device to the Airport Express it only "listens" to AirPlay connections from devices connected to that wired interface. But this is the opposite of what I want. I want it to listen to AirPlay connections from wireless devices connected to the same network as the Airport Express. Is this possible? Is there some hidden setting I have to enable?
Thanks!

Hi Hreb,
I can find nothing wrong with your configuration, but I was curious if there were something illegal about having an Express "join" a wireless network, and still have AirPlay enabled for wireless clients while simultaneously serving as a bridge to a wired one.
To address that uncertainty I implemented your proposed application with the preceding model AirPort Express, and determined it works as you would expect it to: I connected a wired-only PC to the Express, verified that it can connect to the Internet, and streamed Airtunes from a Mac to speakers connected to the Express. I think this is what you want, and it works with no surprises. I was also able to stream Airtunes from the PC connected to the Express as you did, but as you know only one device can stream to the Express at any one time.
I do not have a new simultaneous dual band Express to test though, so all I can conclude is that there may be a bug with the new one that is preventing you from accomplishing this.
Since it is new, I recommend you call Applecare on Monday and explain what you are trying to do. Explain it works with the older Express and you think this ability should remain unchanged with the new dual band model. It is likely they won't be able to help, and at best will offer to exchange it for another one, but if it is a bug as I suspect any replacement dual-band Express will behave the same way.
The important thing is to inform Apple and obtain a case number so that this problem will eventually get the attention of Engineering who might be able to address this with a future update.
Let me know what you find out. Thanks.

How Do I Connect An Airport Extreme With Password to another Wireless Devic

We have a setup for two different wireless devices so that there are multiple locations that can get online, but the entire setup has no passwords assigned. We would like to assign passwords to both wireless devices so that only the appropriate people are getting online. How does one do this?
The first wireless device that connects directly to the modem from the phone company is a brand new Apple Airport Extreme. The computer that set up the device so that people can get a signal was from a PC that is directly connected to the Airport Extreme via an ethernet cable. Also connected to the Airport Extreme is an ethernet cable that goes (50-100ft) to another wireless device - by Netgear - which then sends out another signal to pick up wireless internet, which is the signal/network that I work from.
If we assign a password to the Airport Extreme, I'm guessing it will complete screw up the connection to the Netgear. How would that be dealt with? And, how could we then, if we wanted, set up a password for the Netgear as well. I've read some initial information on the user guide CD and online, but I don't know the terminology of whether these are networks or just wireless devices 'bridged' together, etc.
My biggest concern, is it works right now, but the owner of the devices wants to put passwords on it and I want to make sure we can keep it working even with passwords. Does anyone know how to easily set up passwords and can I do it from my computer even though they were initially set up by a PC? Or do I have to do it from the PC and if so, how, because I am completely a Mac person and am very unfamiliar with Windows. Thanks.

Question that I need to know now is how do we set up a password on the Apple Airport Extreme now, when it is already set up and working without one?
Open AirPort Utility.
Select your base station, and then choose Manual Setup from the Base Station menu. Enter the base station password if necessary.
Click AirPort in the toolbar, and then click Wireless.
Choose a password scheme from the Wireless Security pop-up menu.
Enter the password all users will need in order to join this wireless network.
AirPort Utility 5.1 Help: Password-protecting your wireless network
Also, are there different types of passwords and if so, what is the most reliable one so that we don't lose connections, time out or have any other quirks?
There are different types of wireless encryption. WPA2 and WPA are the most secure especially when used with a non-dictionary password. 128 bit WEP is passable in most situations but not very strong. 40/64 bit WEP is extremely weak.
There is really no general "reliability" issue with any of them. Some devices aren't compatible with some of them.
If when we assign a password to the Apple Airport Extreme and for some reason the Netgear stops working, how do we unassign/take away the password on the Airport to get it back to the current setup that we know does work?
Follow the procedure above but disable wireless encryption instead of enabling it.

WRT54GS-Wireless devices either won't connect or disconnect when a game is launched

My old router went out last night, and I had a wrt54gs that was given to me a while back, so I hooked it up, but I am having some issues with it.
For a while it would say that it had no internet access, when it was connected. Then I couldn't get my wireless devices to connect (xbox, and cell phone) All I had done was change the name and the encryption to WEP.
I was able to get them online when I switched to WPA2 for a while. Then I decided to play a game (Tried Diablo 3 and Path of Exile) Every time I loaded up the game, the devices would get kicked off. WHen I disconnected from the game, they would reconnect to the network. Until 1 time they didn't. Now my Xbox wont connect at all, and my phone keeps saying the network is not in range, when placed a foot from the router. I've tried disabling UPnP, but that doesn't do anything. I've turned MAC filtering, on and off. I've powercycled, and just get no good results.
I'm not sure if this is just a bad router, or whats, going on. (FYI my old router was a 10 yr old D-link that I never had problems with)
Here is my ipconfig..any ideas? Firmware version is 7.2.08
Windows IP Configuration
Host Name . . . . . . . . . . . . : Dream
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Broadcast
IP Routing Enabled. . . . . . . . : No
WINS Proxy Enabled. . . . . . . . : No
Ethernet adapter Local Area Connection:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Realtek RTL8168C(P)/8111C(P) Family PCI-E
Gigabit Ethernet NIC (NDIS 6.20)
Physical Address. . . . . . . . . : 00-1F-D0-D2-72-C6
DHCP Enabled. . . . . . . . . . . : Yes
Autoconfiguration Enabled . . . . : Yes
Link-local IPv6 Address . . . . . : fe80::e859:6ea9:a69c:23b7%10(Preferred)
IPv4 Address. . . . . . . . . . . : 192.168.2.100(Preferred)
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Lease Obtained. . . . . . . . . . : Sunday, August 12, 2012 6:54:20 PM
Lease Expires . . . . . . . . . . : Monday, August 13, 2012 10:14:05 PM
Default Gateway . . . . . . . . . : 192.168.2.1
DHCP Server . . . . . . . . . . . : 192.168.2.1
DHCPv6 IAID . . . . . . . . . . . : 234889168
DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-13-06-8F-85-00-1F-D0-D2-72-C6
DNS Servers . . . . . . . . . . . : 24.217.0.5
24.217.201.67
24.247.15.53
NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter isatap.{F3C3BCCF-D72F-401D-8DA5-01ACBE50DF61}:
Media State . . . . . . . . . . . : Media disconnected
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Microsoft ISATAP Adapter
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
Tunnel adapter Local Area Connection* 9:
Connection-specific DNS Suffix . :
Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
DHCP Enabled. . . . . . . . . . . : No
Autoconfiguration Enabled . . . . : Yes
IPv6 Address. . . . . . . . . . . : 2001:0:4137:9e76:825:2a05:b47b:eaeb(Prefe
rred)
Link-local IPv6 Address . . . . . : fe80::825:2a05:b47b:eaeb%12(Preferred)
Default Gateway . . . . . . . . . : ::
NetBIOS over Tcpip. . . . . . . . : Disabled

What are the details on the camera (Make, model, etc) ?
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it.
If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

I just got my cable company to switch my wireless router to a wired one considering now I have the wireless airport device (the newest one) but now I can't get a wireless signal. The router works when directlyplugged in,the aiport wireless device is green

I just got my cable company to switch my wireless router to a wired one considering now I have the wireless airport device (the newest one) but now I can't get a wireless signal. The router works when directlyplugged in,the aiport wireless device is green. I've tried going through my new MacBook Pro settings and it the diagnostics check, it says network changes detected, I tell it that it "yes" does connect to a cable modem, it tells me to restart it, after I do it asks if there are any other devices hooked up ( firewall) and when I say no it tells me that it can't fix the problem.
Now I know that I probably have a new IP address because of the cable company switching the boxes but it was working fine with the other box, now there isn't a signal to be had on it!
Please anybody out there that can help!!!??

Any time you change networking hardware it is always a good idea to perform a complete power recycle with the new equipment. Check out the following AirPort User Tip. Please post back your results.

When is it possible to have the same User Interface for all screensizes?

Hi all, i am final year student doing some research about User Interface Fragmentation on Mobile devices. As we already know, there are a huge variety of mobile screen sizes, and usually to provide users the best experience interfaces, we often have to customize the UI of one application in one phone to another. So i wondered when it is OK to have the same UI for all screen sizes?
Thanks.

It's usually OK if you don't use CustomItem, avoid extra-long Strings in titles etc. You might also need to scale any Canvas / GameCanvas graphics and Images using a scaling factor computed from the detected screen size.
I have 3 applications for free download from GetJar.com (search "Colorz") which have only the one version for all MIDP 2.0 devices, and there have been no complaints in a combined total of over 11,000 downloads ;-)
In any case, UI diversity is the least of the headaches any j2me developer faces, there are many features of j2me that are unimplemented or incorrectly implemented on various devices. Even the CLDC reference implementation has unaddressed bugs.
luck, db

Help! Is there a limit to number of wireless devices defined in the FIOS router?

My current settings:
I have an Actiontec MI242WR router at home for my FIOS Internet/TV connections. Security setting in the router is set to WPA2 and SSID broadcast is set to 'Disabled'. We've had this router for a number of years and everything seems to work fine.
My issue:
Currently, I have 10 wireless devices defined in the router, set to be the only devices accepted by the router. they are all normal devices such as laptops, printers, smartphones, etc, defined through menus (Wireless settings/Advanced security settings/wireless MAC authentication).
They all work fine but it seems when I add a new wireless device, it drops one of the previously defined devices from the list. Can't remember if drops the last or the first one previously defined. I'm trying to add about three or four more wireless devices to the list but can't afford to drop any of the other ones. Is this a limitation of this router? Am I doing something wrong? Do I need to buy my own router to replace it with? Thanks for your help in advance
Solved!
Go to Solution.

#1 With MAC Address filtering there are the following problems/issues:
a) Regardless of the type of encryption (Wireless encryption types include WEP, WPA, WPA2) MAC Address(es) are always sent in the clear!
b) Not only it is possible to spoof/clone a MAC address in a NAT router..
For example as noted as shown at http://ui.linksys.com/files/WRT54G/v8/8.00.0/WanMAC.htm
..it is also possible to spoof/clone the MAC Address on a computer!
c) If an attacker user does not know how to spoof/clone a MAC address without encryption: While they can not use your network, they can see what you are doing!
#2 So just use the highest level of wireless encryption that all of your gear supports.
If you are the original poster (OP) and your issue is solved, please remember to click the "Solution?" button so that others can more easily find it. If anyone has been helpful to you, please show your appreciation by clicking the "Kudos" button.

This advertised application will not be installed because it might be unsafe. Contact your administrator to change the installation user interface option of the package to basic.

Hi there,
I was wondering whether anyone could tell me which feature in Windows 7 produces this message "This advertised application will not be installed because it might be unsafe. Contact your administrator to change the installation user interface option of
the package to basic." and whether it can be turned off in Windows to prevent this message from appearing when installing certain programs that aren't WHQL certified. At first I thought it was the UAC control that generated this message but found out
that it wasn't and then thought it was the DEP control and found out that it wasn't this either. I'm only seem to be getting this message when installing FileDirector Component Service Version 3 on a few of our workstations which is an add-on that allows file
integration with Office and is part of FileDirector WinClient Version 3.
Your help would be much appreciated.
Many thanks,
RocknRollTim
P.S. I know of a way to bypass this message but would ideally not like to have the feature turned on and for the message not to be appear for non WHQL certified program installations in order to make non WHQL certified program installations in the future much
easier, more simpler and straightforward to carry out. I was redirected by a moderator off the Microsoft Community Forum.

Hi,
You can try following options to disable this prompt, but we don't recommend you to do so since this feature helps you to protect your computer.
Option 1: Run command as admin:
bcdedit -set loadoptions DDISABLE_INTEGRITY_CHECKS
bcdedit -set TESTSIGNING ON
Restart your computer to apply changes.
Option 2: Disable in GPO:
1.Type gpedit.msc in the Run dialog and press Enter.
2.In the Group Policy Editor, navigate to User Configuration → Administrative Templates → System → Driver Installation.
3.Double-click on Code signing for device drivers in the right-side pane as shown above.
4.In the windows that opens, choose Enabled. In the Options, choose Ignore as shown. Then click on the OK button to save the settings.
Restart your computer to apply changes.
Kate Li
TechNet Community Support
Unmarked as Answer based on OP's request.
https://social.technet.microsoft.com/Forums/en-US/35ab1279-c3a1-46be-9f7d-45e8606c1410/this-advertised-application-will-not-be-installed-because-it-might-be-unsafe-contact-your?forum=w7itproappcompat
Arnav Sharma | http://arnavsharma.net/ Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading
the thread.

Cs6 user interface too small to use

I have just bought a new laptop with a high resolution screen - 2560x1440 - and like many others, I'm finding that the user interface for my cs6 software is too small to use.
I have just found the following advice for HiDPI devices on Adobe Illustrator Help:
For displays with resolution greater than or equal to 2560*1440, Illustrator can be launched at 1.5 times or 2 times scaled-up UI, depending on the OS text size.
I'm not very computer savvy, and I don't know how to do that - can anybody help please?
Judith

This only applies to Mac, not Windows.
Mylenium

ISE Profiling for Wireless Devices (WLC 5508) like Laptops and Mobile Devices

Hi,
We have integrated WLC 5508 to cisco ise 3315 with ios 1.1.1 and using Guest Sponsor portal for wireless guest users.
Where we have created open ssid in wlc and redirect web login portal in wlc for guest users. We have enable all respective node in policy service for profiling and also configure snmp in wlc as well as in ise.
When guest user is connected to open ssid its get redirected to web login page of ise portal and when it gets login we are only able to see the username which guest user login but not the end device in monitoring log.
Wireless End devices are not able to get profiled can any one tell me what configuration I need to do on ise or wlc side to profiled end guest wireless device like android,iphone and laptops
Thanks
Pranav

Hi Tarikh,
I only want to identify the end devices for wilress guest user. I have configured MAB Authentication and configure autorization policy where in mention identity group any condition as wlc web authentication and athorization profile only guest mentioning plain access for the same.
Can you help me how I can achived profiling for wirless guest devices. I have configured all profiling probes . Enable snmp on wlc as well as in network devices.
What else I need to configured to achived just identiting device nothing but profiling and which should reflect in authnetication logs.
Thanks
Pranav

Login error in User Interface

Hello, my name is Jo�o Rocha and I'm form UTAD Portugal.
I have installed Identity Manager 7.1 in my University.
I have configured my mandatory resource and at this moment all the account have been succefully reconsiliated.
My problem now is two give access to them on the User Interface. All the account have the same error when they try to login on it.
"Login attempt failed for user xxxxxxx.
- Identity Manager (Identity Manager): ==> com.waveset.util.WavesetException: User object xxxxxx has no cache, it cannot resolve the reference to ObjectGroup object 9AE29A978E2542E3:-6242EBAD:11633A49731:-47CA."
Can Somebody HELP ME!!!!!
sorry about my bad english
Edited by: jrocha on Nov 14, 2007 9:56 AM

Helki,
please verify if you are using Server Based Recording (SPAN) or network recording via BIB in UCM?
If you are using Network Recording, ensure your devices are setup in the VoIP Device Table as such, and either users are assigned directly to a Device, or Profile if using Extension Mobility.
If doing Network recording, and no files are being generated on the record server, then there is probably an issue with the CUCM Monitoring and Recording configuration.
Highlevel this is how it works:
CUCM Sends QM Record Server SIP Invite
     QM Record Server sends ACK, and response with Recording Ports for Phone to send RTP
          Phone forks MediaStreams to ports of QM Record Server
               QM Record Server records call
Once QM Record server recieves a SIP invite it will generate a file, so start there:
The Link provides steps for CUCM configuration:
http://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cucm/admin/8_5_1/ccmfeat/fsgd-851-cm/fsmr.html#wp1048989
If you are doing Server Based Recording (SPAN), a Monitor Server must be a Physical server.
then a SPAN configuration sends RTP directly to the Monitor Server and the Record server records interesting traffic.

What wireless device should I buy?

I'm getting a new desktop and I need a wireless device. I connect to a WPA-encrypted 802.11g network.
Please don't point me to a wiki or some other site. I just need someone to post here that they bought *blank* wireless device and use WPA and it works perfectly.
I don't care if it's USB or PCI or Witch-Craft interface. I cannot stand the frustration of wireless internet in Linux. I want a card that will work with just the Arch 2008 core iso. If you withhold any information, you are a bad, bad person.
Thank you!

As for me, you should use ASUS or NETGEAR cards.
I have no problems with them.
If there any problems with drivers installation you can use NDISWRAPER
But don't use D-LINK 'cause original schematic of impulse power suply is "unstable" and it can burn out
your card or AP. This caused by using btm-like components which are unstable on higher frequencies. (higher than 2 ghz and we have 2.4 ghz) And TP-link cards is "Chinese modified" D_LINK and it is more stable.
I think that the best way to power up your linux with wireless device is to use Atheros or Prism chipsets.
If you want "much powerfull" connection you should use Orinoco Gold card. This thing will blow up all the chanells.
There are nice Planet cards and AP's supported by wireless-ng. Why Planet?
Planet ARM's (CPU's) on AP's are about 166-233 mhz, but there are a lot of stuff on them.
And they've got much power - about 850 mW
As for me, if you don't whant to play with drivers you should use AP's.
Greatest AP that I've ever seen is Senao Deluxe. This series of AP's is about 1W of power!!! But there are some problems with their inner stuff.

Home Hub v1 non-responsive user interface

I haven't used the home hub for a couple of years, but because of ongoing IP profile problems I've got it out of storage to use in place of my Draytek 2600.
Using the internet works fine, but more often than not when I'm trying to configure application sharing, or fixed IP addresses, etc. the hub user interface just freezes and won't respond. Only solution is to turn the hub off and back on.
Is there a fix to this problem of a non-responsive hub user interface?

tarbat wrote:
Higmeister wrote:
The white Hub 1.0?
Reset it to factory defaults by holding the wireless ass. button on the back of the hub down until all the lights go off and then try again.
Yes, I believe it's a Hub 1.0. It's white, and very old.
Keith_Beddoe wrote:
What software version is it currently on? If its been in storage it probably has not been updated.
It says firmware version 6.2.2.6. Is that the latest?
No, but it's the last version that allowed telnet access. Mine's locked to that version for that reason.
I do find the browser interface sluggish at times, but I don't use it much as the telnet/CLI allows for much more control and configuration.
Official firmware version details at:
http://bt.custhelp.com/app/hub/c/346,1887,1892/a_id/9377

Wireless Device User Interface

Similar Messages

Maybe you are looking for