Wireless Network is slow after putting cisco wireless controller
Hello Guys,
My wireless network was very good before putting Cisco WLC 4402 with version 3.2.171.6.
In my network there are two SSID's one for official and another for guest, which is working one single LAP 1142.( Total 12 LWAP is here)
we decided to manage all the ap and deployed WLC but now wireless network is very slow, local gateways is pinging with 80 ms. before WLC it was 1 ms.
Pls. suggest or come up with question to reach a solution.
reg
sanjeev
Hi,
yah it's gigabit support and i have connected with fibre patch cord.
My SWITCH port config is below.
interface GigabitEthernet1/0/25
switchport trunk encapsulation dot1q
switchport mode trunk
Controller sh run
System Inventory
Switch Description............................... Cisco Controller
Machine Model.................................... AIR-WLC4402-12-K9
Serial Number.................................... FOC1105F01E
Burned-in MAC Address............................ 00:1A:6D:DD:23:00
Crypto Accelerator 1............................. Absent
Crypto Accelerator 2............................. Absent
Power Supply 1................................... Absent
Power Supply 2................................... Present, OK
Press Enter to continue Or to abort
System Information
Manufacturer's Name.............................. Cisco Systems, Inc
Product Name..................................... Cisco Controller
Product Version.................................. 3.2.171.6
RTOS Version..................................... 3.2.171.6
Bootloader Version............................... 3.2.171.6
Build Type....................................... DATA + WPS
System Name...................................... SFA-CTRL2-HQ
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.14179.1.1.4.3
IP Address....................................... 10.156.11.231
System Up Time................................... 0 days 11 hrs 9 mins 43 secs
Configured Country............................... United States
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +38 C
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 4
3rd Party Access Point Support................... Disabled
Number of Active Clients......................... 115
Press Enter to continue Or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
Current LWAPP Transport Mode..................... Layer 3
LWAPP Transport Mode after next switch reboot.... Layer 3
FIPS prerequisite features....................... Disabled
Press Enter to continue Or to abort
Network Information
RF-Network Name............................. UNISFA
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Mode..................... Disable Mode: Ucast
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
ARP Unicast Mode............................ Disabled
Cisco AP Default Master..................... Disable
Mgmt Via Wireless Interface................. Enable
Bridge AP Zero Config....................... Enable
Bridge Shared Secret........................ youshouldsetme
Allow Old Bridging Aps To Authenticate...... Enable
Over The Air Provisioning of AP's........... Enable
Mobile Peer to Peer Blocking................ Disable
Apple Talk ................................. Disable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Fast SSID Change ........................... Disabled
Press Enter to continue Or to abort
Port Summary
STP Admin Physical Physical Link Link Mcast
Pr Type Stat Mode Mode Status Status Trap Appliance POE
1 Normal Forw Enable Auto 1000 Full Up Enable Enable N/A
2 Normal Disa Enable Auto 1000 Full Down Enable Enable N/A
Press Enter to continue Or to abort
AP Summary
AP Name Slots AP Model Ethernet MAC Location Port
AP_MHQ_CMS_OFFICE 2 AIR-LAP1242AG-A-K9 00:19:30:76:75:42 default location 1
AP01-MHQ-HOM 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:be default location 1
AP01_MHQ_AIROPS 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6c:84 default location 1
AP01_MSA_HOM_RES 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6b:e2 default location 1
AP10-MHQ-CCITS 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:82 default location 1
AP01-MSA2-TC5 2 AIR-LAP1242AG-A-K9 00:1d:45:36:6d:44 default location 1
AP01_MSA_CableTV_Room 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:aa default location 1
AP01_MSA_RUS_ROOM 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:00 default location 1
AP01-MHQ-JLOC 2 AIR-LAP1242AG-A-K9 00:19:30:76:7f:d0 default location 1
AP01-MSA-C2-D 2 AIR-LAP1242AG-A-K9 00:19:30:76:74:90 default location 1
AP01_MSA_DA7 2 AIR-LAP1242AG-A-K9 00:19:30:76:80:38 default location 1
AP01_MSA_CMS_RES 2 AIR-LAP1242AG-A-K9 00:19:30:76:83:f0 default location 1
Press Enter to continue Or to abort
AP Config
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP_MHQ_CMS_OFFICE
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:75:42
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.240
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3U8
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:a2:d9:d3:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP_MHQ_CMS_OFFICE
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:75:42
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.240
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3U8
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:a2:d9:d3:60
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 24
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP01-MHQ-HOM
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:be
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.238
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3W4
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fc:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 2
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. Side A or Right Connector
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP01-MHQ-HOM
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:be
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.238
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3W4
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fc:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... AP01_MHQ_AIROPS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6c:84
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.232
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X7
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d9:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. Side A or Right Connector
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 3
Cisco AP Name.................................... AP01_MHQ_AIROPS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6c:84
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.232
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X7
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d9:60
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... AP01_MSA_HOM_RES
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6b:e2
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.239
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X1
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d4:30
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 11
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 4
Cisco AP Name.................................... AP01_MSA_HOM_RES
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:1d:45:36:6b:e2
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.239
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1135B2X1
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211a
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1d:46:7e:d4:30
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... MANDATORY
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 15 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 149
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP10-MHQ-CCITS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:82
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.233
IP NetMask....................................... 255.255.254.0
Gateway IP Addr.................................. 10.156.10.1
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch.............................
Secondary Cisco Switch...........................
Tertiary Cisco Switch............................
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Remote AP Debug ................................. Disabled
S/W Version .................................... 3.2.171.6
Boot Version ................................... 12.3.7.1
Mini IOS Version ................................ 3.0.51.0
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1242AG-A-K9
IOS Version...................................... 12.3(7)JX6
Reset Button..................................... Enabled
AP Serial Number................................. FTX1107B3TJ
AP Certificate Type.............................. Manufacture Installed
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211g
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
WLAN Override ............................... Disabled
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 2
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 00:1a:30:e7:fa:60
Operation Rate Set
1000 Kilo Bits........................... MANDATORY
2000 Kilo Bits........................... MANDATORY
5500 Kilo Bits........................... MANDATORY
11000 Kilo Bits.......................... MANDATORY
6000 Kilo Bits........................... SUPPORTED
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... SUPPORTED
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... SUPPORTED
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
Beacon Period ............................. 100
DTIM Period ............................... 1
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ US
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 11
MAC Operation Parameters
Configuration ............................. AUTOMATIC
RTS Threshold ............................. 2347
Short Retry Limit ......................... 7
Long Retry Limit .......................... 4
Fragmentation Threshold ................... 2346
Maximum Tx MSDU Life Time ................. 512
Maximum Rx Life Time ...................... 512
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
TI Threshold .............................. -50
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBm units).... 0
Diversity.................................. DIVERSITY_ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
Cisco AP Identifier.............................. 5
Cisco AP Name.................................... AP10-MHQ-CCITS
AP Regulatory Domain............................. -A
Switch Port Number .............................. 1
MAC Address...................................... 00:19:30:76:74:82
IP Address Configuration......................... Static IP assigned
IP Address....................................... 10.156.11.233
IP NetMask.........
Similar Messages
-
I have connected my time capsule to motorola SG6580 modem via ethernet. I have a wireless network on the motorola and a wireless network from the time capsule. I get duplicate IPs error messages (no connection) sometimes when trying to connect devices to the wireless network. How do I fix? Sometimes devices cannot connect to the network because of conflicting IPs. I look on the Motorola and every device has a unique IP assigned but occasionally a device has taken the IP of another device. I have been writing down all the devices and the IPs they have been using. It happens more with PCs than Macs, ipads or iPhones.
If the Time Capsule is set up correctly in bridge mode, then it is the responsibility of the Motorola modem/router to provide the correct IP address assignments for all devices on the network.
Check to insure that the Time Capsule is correctly set up to operate in bridge mode as follows:
On your Mac, open AirPort Utility
Finder > Applications > Utilities > AirPort Utility
Click on the Time Capsule icon, then click Edit in the smaller window that appears
Click the Network tab at the top of the next window
Insure that the setting for Router Mode is configured to read "Off (Bridge Mode)"
Once you have confirmed that the Time Capsule is configured correctly, everything else is the responsibility of the Motorola modem/router as far as network routing and IP address assignments for devices.
If you continue to have IP address issues, then you should contact the Internet Service Provider (ISP) that provided the Motorola device to you and ask them to fix the issue. -
Extend Wireless Network using a Telstra technicolor Gateway wireless Router to Airpot extreme but Airport will only except "join a wireless network (which it does) not "extend a wireless network" (Led turns yellow and I can not get a network working on the Airpor Extreme ethernet ports but can ping Airport extreme from Technicolor Router.
Airport gets it address DHCP.Funny how I can ping the Extreme but the Hard Ethernet ports dont seem to work correctly.
When the AirPort Extreme is configured to "Join" a wireless network, the Ethernet ports are not enabled.
Oddly, the AirPort Express has a special feature that will allow it to to "Join" virtually any wireless network.....and the Ethernet port can be enabled. So, an Express would work for your purpose to provide an Ethernet connection to the media player. This assumes that the Express is located where it can receive a strong wireless signal from your main router.
Note that the Express will not provide any additional wireless coverage when it "Joins". -
I have a Netgear wndr3400 and I can "join a wireless network" but can not "extend a wireless network" on my Airport express. Does anyone know why?
Sorry, but "Extend a wireless network" is a proprietary Apple setting that will only work if you have another Apple router.
It is not compatible with devices from other manufacturers. -
Cisco Aironet 1200 wireless network very slow
I have a simple wireless network set up, 2 - Cisco Aironet 1200 AIR-AP1220B-A-K9 wireless access points with 2 dBi Diversity Omni directional Ceiling Mount Antennas. They are the only devices connected to a Multitech Routfinder router, the WAN side the router is connected to a dedicated DSL connection. They are powered by AIR-PWRINJ3 power injectors. The WAP get the IP address from the DHCP in the router.
When connecting to the wireless network it runs very very slow, the signal strength is excellent and the connection speed is 54 mbps. But when opening a web browser it takes for ever to load a simple page like msn.com. If I connect the notebook directly to the router it runs very fast. We have tested with several notebooks and have the same problem. When I view the available wireless networks in range the only two that show up are the two Cisco 1200 WAP.
I have done the following with no improvement:
Change the channels from auto to 6 on one and 11 on the other.
Reset to factory defaults.
Update the firmware to c1200-k9w7-tar.123-7.JA2.tar
Replace the 802.11b radios with 802.11g radios AIR-MP21G-A-K9.
Disable the Aironet extensions.
Following is the configuration from one of the access points (before the firmware update):
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname MMA1
aaa new-model
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login default local
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa authorization ipmobile default group rad_pmip
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
username xxxx privilege 15 password xxxx
username xxx privilege 15 password xxxx
ip subnet-zero
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
ssid MMA1
authentication open
guest-mode
speed basic-1.0 basic-2.0 basic-5.5 basic-11.0
rts threshold 2312
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.10.100 255.255.255.0
no ip route-cache
ip default-gateway 192.168.10.1
ip http server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag/ivory/1100
ip http authentication aaa
bridge 1 route ip
line con 0
line vty 5 15
End
Any suggestions would be greatly appreciated.
Best regards,
RandyThanks for the info.
The documentation say not to switch from auto to full duplex or half duplex when using inline power, well I think it says the AP may reboot. I may have tried half duplex before I upgraded the firmware.
While upgrading I disconnected the AP, used a patch cord to connect it to the router and pluged the power directly into it to make sure the wiring to the AP was not the problem and it did the same thing.
However, when trying to upgrade the firmware it took ~ 45 minuets to upload the image and filed a couple of times retrying. I connected the AP to the notebook directly with a crossover cable and it uploaded in about 45 seconds.
That got me to thinking that there may be a problem with the router so I have replaced it with a Linksys.
In the mean time the DSL went down yesterday so I have not been able to test the new setup.
The cables are T568B
W/O
O/W
W/G
B/W
W/B
G/W
W/B
B/W
Best regards,
Randy -
[SOLVED] Cannot connect to wireless networks any more after update
Hello,
I updated my system some days ago and, after that, I can't connect to wireless networks any more.
My network card is ath9k and I'm currently using wicd.
When I try to connect to my wireless network, I get "Veryfing AP association" message, then it fails to connect.
Here's the dmesg output :
[ 6369.650201] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6369.824358] r8169 0000:05:00.0 eth0: link down
[ 6369.824375] r8169 0000:05:00.0 eth0: link down
[ 6369.824398] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6369.936721] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6371.462702] r8169 0000:05:00.0 eth0: link up
[ 6371.462718] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6373.214209] wlan0: authenticate with 00:1c:10:57:47:17
[ 6373.236813] wlan0: send auth to 00:1c:10:57:47:17 (try 1/3)
[ 6373.248706] wlan0: authenticated
[ 6373.248735] ath9k 0000:09:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 6373.248737] ath9k 0000:09:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 6373.248739] ath9k 0000:09:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 6373.250756] wlan0: associate with 00:1c:10:57:47:17 (try 1/3)
[ 6373.253150] wlan0: RX AssocResp from 00:1c:10:57:47:17 (capab=0x411 status=0 aid=3)
[ 6373.253379] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 6373.253418] wlan0: associated
[ 6373.253431] ath9k 0000:09:00.0 wlan0: failed to set key 0
[ 6405.384916] wlan0: deauthenticating from 00:1c:10:57:47:17 by local choice (reason=3)
[ 6405.387398] cfg80211: Calling CRDA to update world regulatory domain
[ 6409.789779] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6409.890892] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6410.069734] r8169 0000:05:00.0 eth0: link down
[ 6410.069750] r8169 0000:05:00.0 eth0: link down
[ 6410.069778] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6410.263183] r8169 0000:05:00.0 eth0: link down
[ 6410.263212] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6411.717705] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6411.898268] r8169 0000:05:00.0 eth0: link down
[ 6411.898297] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6413.630832] r8169 0000:05:00.0 eth0: link up
[ 6413.630848] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 6415.903790] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 6416.089275] r8169 0000:05:00.0 eth0: link down
[ 6416.089302] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6416.089327] r8169 0000:05:00.0 eth0: link down
[ 6416.386308] r8169 0000:05:00.0 eth0: link down
[ 6416.386338] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 6418.067675] r8169 0000:05:00.0 eth0: link up
[ 6418.067691] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
This particular line caught my attention: " wlan0: de-authenticating from 00:1c:10:57:47:17 by local choice (reason=3)". So I searched for it (without the MAC address) on the internet and found several solutions for it, involving wpa_supplicant, dhcpcd, IPv6 (disable it on /etc/sysctl.d/40-ipv6.conf) and card power management (operation not supported, don't have option on BIOS), but none of them worked for me.
Here's an excerpt from /var/log/wicd/wicd.log:
2014/03/01 11:48:15 :: Connecting to wireless network Curiosity
2014/03/01 11:48:15 :: Putting interface down
2014/03/01 11:48:15 :: Releasing DHCP leases...
2014/03/01 11:48:15 :: Setting false IP...
2014/03/01 11:48:15 :: Stopping wpa_supplicant
2014/03/01 11:48:15 :: Flushing the routing table...
2014/03/01 11:48:15 :: Putting interface up...
2014/03/01 11:48:17 :: Attempting to authenticate...
2014/03/01 11:48:19 :: Setting static IP : 192.168.2.188
2014/03/01 11:48:19 :: Setting default gateway : 192.168.2.1
2014/03/01 11:48:19 :: Verifying AP association...
2014/03/01 11:48:19 :: Attempt 1 of 10...
2014/03/01 11:48:24 :: Attempt 2 of 10...
2014/03/01 11:48:27 :: Attempt 3 of 10...
2014/03/01 11:48:30 :: Attempt 4 of 10...
2014/03/01 11:48:33 :: Attempt 5 of 10...
2014/03/01 11:48:36 :: Attempt 6 of 10...
2014/03/01 11:48:39 :: Attempt 7 of 10...
2014/03/01 11:48:42 :: Attempt 8 of 10...
2014/03/01 11:48:45 :: Attempt 9 of 10...
2014/03/01 11:48:48 :: Attempt 10 of 10...
2014/03/01 11:48:51 :: Connection Failed: Failed to ping the access point!
2014/03/01 11:48:51 :: exiting connection thread
2014/03/01 11:48:55 :: Sending connection attempt result association_failed
2014/03/01 11:48:55 :: Autoconnecting...
2014/03/01 11:48:55 :: Attempting to autoconnect with wired interface...
2014/03/01 11:48:55 :: Putting interface down
2014/03/01 11:48:55 :: Releasing DHCP leases...
2014/03/01 11:48:55 :: Setting false IP...
2014/03/01 11:48:55 :: Stopping wpa_supplicant
2014/03/01 11:48:55 :: Flushing the routing table...
2014/03/01 11:48:55 :: Putting interface up...
2014/03/01 11:48:58 :: Setting static IP : 192.168.2.188
2014/03/01 11:48:58 :: Setting default gateway : 192.168.2.1
2014/03/01 11:48:58 :: Connecting thread exiting.
2014/03/01 11:49:01 :: Putting interface down
2014/03/01 11:49:01 :: Releasing DHCP leases...
2014/03/01 11:49:01 :: Setting false IP...
2014/03/01 11:49:02 :: Stopping wpa_supplicant
2014/03/01 11:49:02 :: Flushing the routing table...
2014/03/01 11:49:02 :: Putting interface up...
2014/03/01 11:49:04 :: Setting static IP : 192.168.2.188
2014/03/01 11:49:04 :: Setting default gateway : 192.168.2.1
2014/03/01 11:49:04 :: Connecting thread exiting.
2014/03/01 11:49:07 :: Sending connection attempt result success
I've been connecting through wire since then and it's extremely uncomfortable being planted in one place.
Thanks.
Last edited by joaowojwicz (2014-04-03 12:17:53)ewaller wrote:Well, let's start with a couple sanity checks. Look at the output of uname -a and of pacman -Qi linux and ensure that the running kernel (uname) is the same version that is installed.
Then. please post the output of lspci -nn and of ip link
Then, take a look at the output of sudo iw wlan0 scan
and see if you can see your AP. Also, verify that your wireless is called wlan0 by checking the ouput of ip link
Okay
>>log: uname -a
Linux Canopus 3.13.5-1-ARCH #1 SMP PREEMPT Sun Feb 23 00:10:07 CET 2014 i686 GNU/Linux
>>log: pacman -Qi linux
Name : linux
Version : 3.13.5-1
Description : The Linux kernel and modules
Architecture : i686
URL : http://www.kernel.org/
Licences : GPL2
Groups : base
Provides : kernel26=3.13.5
Depends On : coreutils linux-firmware kmod mkinitcpio>=0.7
Optional Deps : crda: to set the correct wireless channels of your country
Required By : None
Optional For : None
Conflicts With : kernel26
Replaces : kernel26
Installed Size : 61687.00 KiB
Packager : Thomas Bächler <[email protected]>
Build Date : Sat 22 Feb 2014 20:11:46 BRT
Install Date : Mon 24 Feb 2014 02:50:00 BRT
Install Reason : Explicitly installed
Install Script : Yes
Validated By : SHA256 Sum
>>log: lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09)
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0116] (rev 09)
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05)
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5)
00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 [8086:1c12] (rev b5)
00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b5)
00:1c.4 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 5 [8086:1c18] (rev b5)
00:1c.7 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 8 [8086:1c1e] (rev b5)
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05)
00:1f.0 ISA bridge [0601]: Intel Corporation HM67 Express Chipset Family LPC Controller [8086:1c4b] (rev 05)
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05)
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
09:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
0b:00.0 USB controller [0c03]: NEC Corporation uPD720200 USB 3.0 Host Controller [1033:0194] (rev 04)
Yes, my wireless is called wlan0. I linked something to /dev/null to get the predictable names
>>log: ip link
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode DEFAULT group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN mode DEFAULT group default qlen 1000
link/ether 94:39:e5:f2:17:3f brd ff:ff:ff:ff:ff:ff
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP mode DEFAULT group default qlen 1000
link/ether 18:03:73:93:4d:1b brd ff:ff:ff:ff:ff:ff
I'll just paste my wireless connection here.
>>log: sudo iw wlan0 scan
BSS 00:1c:10:57:47:17(on wlan0)
TSF: 59645240249 usec (0d, 16:34:05)
freq: 2462
beacon interval: 100 TUs
capability: ESS Privacy ShortSlotTime (0x0411)
signal: -31.00 dBm
last seen: 260 ms ago
Information elements from Probe Response frame:
SSID: Curiosity
Supported rates: 1.0* 2.0* 5.5* 11.0* 18.0 24.0 36.0 54.0
DS Parameter set: channel 11
ERP: Barker_Preamble_Mode
ERP D4.0: Barker_Preamble_Mode
Extended supported rates: 6.0 9.0 12.0 48.0
karol wrote:
Post the list of packages that were updated.
When posting configs, code or command output, please use [ code ] tags, not [ quote ] tags https://bbs.archlinux.org/help.php#bbcode
like this
It makes the code more readable and - in case of longer listings - more convenient to scroll through.
Okay, put code tag now. Here's the whole log since Feb, 24th. This was the day I started having problems.
[2014-02-24 02:32] [PACMAN] Running 'pacman -Suy'
[2014-02-24 02:32] [PACMAN] synchronizing package lists
[2014-02-24 02:32] [PACMAN] starting full system upgrade
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Appending keys from archlinux.gpg...
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: 3 marginal(s) needed, 1 complete(s) needed, PGP trust model
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: depth: 0 valid: 1 signed: 6 trust: 0-, 0q, 0n, 0m, 0f, 1u
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: depth: 1 valid: 6 signed: 60 trust: 1-, 0q, 0n, 5m, 0f, 0u
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: depth: 2 valid: 60 signed: 4 trust: 60-, 0q, 0n, 0m, 0f, 0u
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: next trustdb check due at 2015-03-31
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Locally signing trusted keys in keyring...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key 0E8B644079F599DFC1DDC3973348882F6AC6A4C2...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key 684148BB25B49E986A4944C55184252D824B18E8...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key 44D4A033AC140143927397D47EFD567D4C7EA887...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key 27FFC4769E19F096D41D9265A04F9397CDFD6BB0...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Locally signing key AB19265E5D7D20687D303246BA1DFB64FFF979E7...
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Importing owner trust values...
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Disabling revoked keys in keyring...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key F5A361A3A13554B85E57DDDAAF7EF7873CFD4BB6...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 7FA647CD89891DEDC060287BB9113D1ED21E1A55...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key BC1FBE4D2826A0B51E47ED62E2539214C6C11350...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 4A8B17E20B88ACA61860009B5CED81B7C2E5C0D2...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 63F395DE2D6398BBE458F281F2DBB4931985A992...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 0B20CA1931F5DA3A70D0F8D2EA6836E1AB441196...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 8F76BEEA0289F9E1D3E229C05F946DED983D4366...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 66BD74A036D522F51DD70A3C7F2A16726521E06D...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key 81D7F8241DB38BC759C80FCE3A726C6170E80477...
[2014-02-24 02:49] [ALPM-SCRIPTLET] -> Disabling key E7210A59715F6940CF9A4E36A001876699AD6E84...
[2014-02-24 02:49] [ALPM-SCRIPTLET] ==> Updating trust database...
[2014-02-24 02:49] [ALPM-SCRIPTLET] gpg: next trustdb check due at 2015-03-31
[2014-02-24 02:49] [PACMAN] upgraded archlinux-keyring (20140124-1 -> 20140220-1)
[2014-02-24 02:49] [PACMAN] upgraded hicolor-icon-theme (0.12-2 -> 0.13-1)
[2014-02-24 02:49] [PACMAN] upgraded banshee (2.6.1-2 -> 2.6.2-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-cups (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-hid2hci (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-libs (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-plugins (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded bluez-utils (5.14-1 -> 5.15-1)
[2014-02-24 02:49] [PACMAN] upgraded cairo-perl (1.103-2 -> 1.104-1)
[2014-02-24 02:49] [PACMAN] upgraded cups-filters (1.0.45-1 -> 1.0.46-1)
[2014-02-24 02:49] [PACMAN] upgraded dbus-glib (0.100.2-1 -> 0.102-1)
[2014-02-24 02:49] [PACMAN] upgraded dialog (1:1.2_20140112-1 -> 1:1.2_20140219-1)
[2014-02-24 02:49] [PACMAN] upgraded easytag (2.1.9-1 -> 2.1.10-1)
[2014-02-24 02:49] [PACMAN] upgraded ethtool (1:3.11-1 -> 1:3.13-1)
[2014-02-24 02:49] [PACMAN] upgraded flashplugin (11.2.202.336-1 -> 11.2.202.341-1)
[2014-02-24 02:49] [PACMAN] upgraded libpng (1.6.8-1 -> 1.6.9-1)
[2014-02-24 02:49] [PACMAN] upgraded gdk-pixbuf2 (2.30.4-1 -> 2.30.5-1)
[2014-02-24 02:49] [PACMAN] upgraded glib-perl (1.301-1 -> 1.304-1)
[2014-02-24 02:49] [PACMAN] upgraded gparted (0.17.0-2 -> 0.18.0-1)
[2014-02-24 02:49] [PACMAN] upgraded pango-perl (1.224-2 -> 1.225-1)
[2014-02-24 02:49] [PACMAN] upgraded gtk2-perl (1.247-2 -> 1.249-1)
[2014-02-24 02:49] [PACMAN] upgraded imagemagick (6.8.8.6-1 -> 6.8.8.7-1)
[2014-02-24 02:49] [PACMAN] upgraded kdesdk-poxml (4.12.2-1 -> 4.12.2-2)
[2014-02-24 02:49] [PACMAN] upgraded libass (0.10.2-2 -> 0.11.1-1)
[2014-02-24 02:49] [PACMAN] upgraded libfm (1.1.2.2-2 -> 1.2.0-3)
[2014-02-24 02:49] [PACMAN] upgraded libftdi (1.1-2 -> 1.1-3)
[2014-02-24 02:49] [PACMAN] upgraded libindi (0.9.6-7 -> 0.9.7-1)
[2014-02-24 02:49] [PACMAN] upgraded linux-firmware (20140123.418320b-1 -> 20140217.343e460-1)
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> Updating module dependencies. Please wait ...
[2014-02-24 02:50] [ALPM-SCRIPTLET] depmod: ERROR: Module 'hci_vhci' has devname (vhci) but lacks major and minor information. Ignoring.
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> Generating initial ramdisk, using mkinitcpio. Please wait...
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'default'
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux.img
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Starting build: 3.13.5-1-ARCH
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [base]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [udev]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [autodetect]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [modconf]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [block]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [filesystems]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [keyboard]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [fsck]
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Creating gzip initcpio image: /boot/initramfs-linux.img
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Image generation successful
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux.preset: 'fallback'
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> -k /boot/vmlinuz-linux -c /etc/mkinitcpio.conf -g /boot/initramfs-linux-fallback.img -S autodetect
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Starting build: 3.13.5-1-ARCH
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [base]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [udev]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [modconf]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [block]
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: aic94xx
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: smsmdtv
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [filesystems]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [keyboard]
[2014-02-24 02:50] [ALPM-SCRIPTLET] -> Running build hook: [fsck]
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Creating gzip initcpio image: /boot/initramfs-linux-fallback.img
[2014-02-24 02:50] [ALPM-SCRIPTLET] ==> Image generation successful
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> WARNING: AT keyboard support is no longer built into the kernel.
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> In order to use your keyboard during early init, you MUST
[2014-02-24 02:50] [ALPM-SCRIPTLET] >>> include the 'keyboard' hook in your mkinitcpio.conf.
[2014-02-24 02:50] [PACMAN] upgraded linux (3.12.9-1 -> 3.13.5-1)
[2014-02-24 02:50] [PACMAN] upgraded linux-headers (3.12.9-1 -> 3.13.5-1)
[2014-02-24 02:50] [PACMAN] upgraded lirc-utils (1:0.9.0-69 -> 1:0.9.0-70)
[2014-02-24 02:50] [PACMAN] upgraded lynx (2.8.7-7 -> 2.8.8-1)
[2014-02-24 02:50] [PACMAN] upgraded man-pages (3.58-1 -> 3.60-1)
[2014-02-24 02:50] [PACMAN] upgraded mercurial (2.9-1 -> 2.9-2)
[2014-02-24 02:50] [PACMAN] upgraded mutter (3.10.3-1 -> 3.10.4-1)
[2014-02-24 02:50] [PACMAN] upgraded networkmanager (0.9.8.8-1 -> 0.9.8.8-3)
[2014-02-24 02:50] [PACMAN] upgraded networkmanager-pptp (0.9.8.4-1 -> 0.9.8.4-2)
[2014-02-24 02:50] [PACMAN] upgraded pcmanfm (1.1.2-2 -> 1.2.0-1)
[2014-02-24 02:50] [PACMAN] upgraded postgresql-libs (9.3.2-4 -> 9.3.3-1)
[2014-02-24 02:50] [PACMAN] upgraded ppp (2.4.5-8 -> 2.4.6-1)
[2014-02-24 02:50] [PACMAN] upgraded python2-configobj (4.7.2-6 -> 5.0.1-1)
[2014-02-24 02:50] [PACMAN] upgraded python2-urwid (1.1.1-1 -> 1.2.0-1)
[2014-02-24 02:50] [PACMAN] upgraded python2-zope-interface (4.0.5-2 -> 4.1.0-1)
[2014-02-24 02:50] [PACMAN] upgraded sbc (1.1-1 -> 1.2-1)
[2014-02-24 02:50] [PACMAN] upgraded t1lib (5.1.2-4 -> 5.1.2-5)
[2014-02-24 02:50] [PACMAN] upgraded totem-plparser (3.10.0-4 -> 3.10.1-1)
[2014-02-24 02:50] [PACMAN] upgraded vimpager (1.8.5-1 -> 1.8.6-1)
[2014-02-24 02:50] [PACMAN] upgraded vlc (2.1.3-1 -> 2.1.4-1)
[2014-02-24 02:50] [PACMAN] upgraded webkitgtk (2.2.4-2 -> 2.2.5-1)
[2014-02-24 02:50] [PACMAN] upgraded wine (1.7.12-2 -> 1.7.13-1)
[2014-02-24 02:50] [PACMAN] upgraded xarchiver (0.5.2-6 -> 0.5.3-1)
[2014-02-24 02:50] [PACMAN] upgraded xcb-util-wm (0.4.0-1 -> 0.4.1-1)
[2014-02-24 02:50] [PACMAN] upgraded xmlto (0.0.25-3 -> 0.0.25-5)
[2014-02-24 02:50] [PACMAN] upgraded youtube-dl (2014.02.13-1 -> 2014.02.22.1-1)
[2014-02-24 12:51] [PACMAN] Running 'pacman -Suy'
[2014-02-24 12:51] [PACMAN] synchronizing package lists
[2014-02-24 12:51] [PACMAN] starting full system upgrade
[2014-02-24 12:57] [PACMAN] upgraded ffmpeg (1:2.1.3-1 -> 1:2.1.4-1)
[2014-02-24 12:57] [PACMAN] upgraded libwbclient (4.1.4-1 -> 4.1.5-1)
[2014-02-24 12:57] [PACMAN] upgraded python2-configobj (5.0.1-1 -> 5.0.1-2)
[2014-02-24 12:57] [PACMAN] upgraded s-nail (14.5.2-4 -> 14.6-1)
[2014-02-24 12:57] [PACMAN] upgraded smbclient (4.1.4-1 -> 4.1.5-1)
[2014-02-24 12:57] [PACMAN] upgraded samba (4.1.4-1 -> 4.1.5-1)
[2014-02-24 12:57] [PACMAN] upgraded xbmc (12.3-8 -> 12.3-9)
[2014-02-24 13:19] [PACMAN] Running 'pacman -Syy'
[2014-02-24 13:19] [PACMAN] synchronizing package lists
[2014-02-24 13:20] [PACMAN] Running 'pacman -Suu dhcpcd'
[2014-02-24 13:20] [PACMAN] starting full system upgrade
[2014-02-24 13:24] [PACMAN] Running '/usr/bin/pacman -U /home/joaowojcikiewicz/z-aur/downgrade/downgrade-3.3-1-any.pkg.tar.xz'
[2014-02-24 13:24] [PACMAN] installed downgrade (3.3-1)
[2014-02-24 16:04] [PACMAN] Running 'pacman -Suy'
[2014-02-24 16:04] [PACMAN] synchronizing package lists
[2014-02-24 16:04] [PACMAN] starting full system upgrade
[2014-02-24 16:04] [PACMAN] upgraded vim-spell-br (20120506-1 -> 20120802-1)
[2014-02-24 16:04] [PACMAN] upgraded vim-spell-en (20120506-1 -> 20120802-1)
[2014-02-24 18:30] [PACMAN] Running 'pacman -Suy'
[2014-02-24 18:30] [PACMAN] synchronizing package lists
[2014-02-24 18:30] [PACMAN] starting full system upgrade
[2014-02-24 20:13] [PACMAN] Running 'pacman -Suy'
[2014-02-24 20:13] [PACMAN] synchronizing package lists
[2014-02-24 20:13] [PACMAN] starting full system upgrade
[2014-02-24 21:31] [PACMAN] Running 'pacman -Suy'
[2014-02-24 21:31] [PACMAN] synchronizing package lists
[2014-02-24 21:31] [PACMAN] starting full system upgrade
[2014-02-24 21:53] [PACMAN] Running 'pacman -Suy'
[2014-02-24 21:53] [PACMAN] synchronizing package lists
[2014-02-24 21:53] [PACMAN] starting full system upgrade
[2014-02-24 22:38] [PACMAN] Running 'pacman -R networkmanager'
[2014-02-24 22:39] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet'
[2014-02-24 22:39] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet kdeplasma-applets-networkmanagement telepathy-mission-control'
[2014-02-24 22:39] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet kdeplasma-applets-networkmanagement telepathy-mission-control empathy telepathy-kde-common-internals'
[2014-02-24 22:40] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet kdeplasma-applets-networkmanagement telepathy-mission-control empathy telepathy-kde-common-internals skype4empathy telepathy-kde-accounts-kcm telepathy-kde-approver telepathy-kde-auth-handler telepathy-kde-contact-list telepathy-kde-contact-runner telepathy-kde-desktop-applets telepathy-kde-filetransfer-handler telepathy-kde-integration-module'
[2014-02-24 22:40] [PACMAN] Running 'pacman -R networkmanager-openvpn networkmanager-pptp networkmanager network-manager-applet kdeplasma-applets-networkmanagement telepathy-mission-control empathy telepathy-kde-common-internals skype4empathy telepathy-kde-accounts-kcm telepathy-kde-approver telepathy-kde-auth-handler telepathy-kde-contact-list telepathy-kde-contact-runner telepathy-kde-desktop-applets telepathy-kde-filetransfer-handler telepathy-kde-integration-module telepathy-kde-send-file telepathy-kde-text-ui'
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-text-ui (0.7.1-2)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-send-file (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-integration-module (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-filetransfer-handler (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-desktop-applets (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-contact-runner (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-auth-handler (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-approver (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-accounts-kcm (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-contact-list (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed skype4empathy (20110407-4)
[2014-02-24 22:40] [PACMAN] removed telepathy-kde-common-internals (0.7.1-1)
[2014-02-24 22:40] [PACMAN] removed empathy (3.10.3-1)
[2014-02-24 22:40] [PACMAN] removed telepathy-mission-control (5.16.0-1)
[2014-02-24 22:41] [PACMAN] removed kdeplasma-applets-networkmanagement (1:0.9.0.9-1)
[2014-02-24 22:41] [PACMAN] removed network-manager-applet (0.9.8.8-1)
[2014-02-24 22:41] [PACMAN] removed networkmanager-pptp (0.9.8.4-2)
[2014-02-24 22:41] [PACMAN] removed networkmanager-openvpn (0.9.8.4-1)
[2014-02-24 22:41] [ALPM] warning: /etc/NetworkManager/NetworkManager.conf saved as /etc/NetworkManager/NetworkManager.conf.pacsave
[2014-02-24 22:41] [PACMAN] removed networkmanager (0.9.8.8-3)
[2014-02-25 03:40] [PACMAN] Running 'pacman -Suy'
[2014-02-25 03:40] [PACMAN] synchronizing package lists
[2014-02-25 03:40] [PACMAN] starting full system upgrade
[2014-02-25 03:44] [PACMAN] upgraded youtube-dl (2014.02.22.1-1 -> 2014.02.24-1)
[2014-02-25 12:23] [PACMAN] Running 'pacman -Suy'
[2014-02-25 12:23] [PACMAN] synchronizing package lists
[2014-02-25 12:24] [PACMAN] starting full system upgrade
[2014-02-25 12:24] [PACMAN] upgraded dmenu (4.5-3 -> 4.5.13.5ed5e90-1)
[2014-02-25 12:24] [PACMAN] upgraded telepathy-glib (0.22.0-1 -> 0.22.1-1)
[2014-02-25 12:24] [PACMAN] upgraded tumbler (0.1.29-1 -> 0.1.30-1)
[2014-02-25 12:25] [PACMAN] upgraded youtube-dl (2014.02.24-1 -> 2014.02.25-1)
[2014-02-25 14:55] [PACMAN] Running 'pacman -Suy'
[2014-02-25 14:55] [PACMAN] synchronizing package lists
[2014-02-25 14:55] [PACMAN] starting full system upgrade
[2014-02-25 15:19] [PACMAN] upgraded ipython2 (1.1.0-1 -> 1.2.1-1)
[2014-02-25 15:19] [PACMAN] upgraded python2-pip (1.5.2-1 -> 1.5.4-1)
[2014-02-25 17:13] [PACMAN] Running 'pacman -Suy'
[2014-02-25 17:13] [PACMAN] synchronizing package lists
[2014-02-25 17:13] [PACMAN] starting full system upgrade
[2014-02-25 18:10] [PACMAN] Running 'pacman -Suy'
[2014-02-25 18:10] [PACMAN] synchronizing package lists
[2014-02-25 18:10] [PACMAN] starting full system upgrade
[2014-02-25 18:41] [PACMAN] Running 'pacman -S fbgrab'
[2014-02-25 18:41] [PACMAN] installed fbgrab (1.0-7)
[2014-02-26 13:19] [PACMAN] Running 'pacman -Suy'
[2014-02-26 13:19] [PACMAN] synchronizing package lists
[2014-02-26 13:19] [PACMAN] starting full system upgrade
[2014-02-26 13:25] [PACMAN] upgraded libmariadbclient (5.5.35-1 -> 5.5.36-1)
[2014-02-26 13:25] [PACMAN] upgraded mariadb-clients (5.5.35-1 -> 5.5.36-1)
[2014-02-26 13:25] [PACMAN] upgraded mariadb (5.5.35-1 -> 5.5.36-1)
[2014-02-26 13:25] [PACMAN] upgraded python2 (2.7.6-2 -> 2.7.6-3)
[2014-02-26 13:25] [PACMAN] upgraded s-nail (14.6-1 -> 14.6.1-1)
[2014-02-26 13:26] [PACMAN] upgraded xbmc (12.3-9 -> 12.3-10)
[2014-02-26 16:00] [PACMAN] Running '/usr/bin/pacman -S --asdeps qt>=4.6'
[2014-02-26 16:02] [PACMAN] Running '/usr/bin/pacman -S --asdeps qt>=4.6'
[2014-02-26 16:42] [PACMAN] Running 'pacman -Suy'
[2014-02-26 16:42] [PACMAN] synchronizing package lists
[2014-02-26 16:42] [PACMAN] starting full system upgrade
[2014-02-26 17:25] [PACMAN] Running 'pacman -Suy'
[2014-02-26 17:25] [PACMAN] synchronizing package lists
[2014-02-26 17:25] [PACMAN] starting full system upgrade
[2014-02-26 17:25] [PACMAN] upgraded libaccounts-glib (1.15-1 -> 1.16-1)
[2014-02-26 17:25] [PACMAN] upgraded libaccounts-qt (1.10-1 -> 1.11-1)
[2014-02-26 17:52] [PACMAN] Running 'pacman -Suy'
[2014-02-26 17:52] [PACMAN] synchronizing package lists
[2014-02-26 17:52] [PACMAN] starting full system upgrade
[2014-02-26 17:53] [PACMAN] upgraded signon (8.55-1 -> 8.56-1)
[2014-02-26 18:08] [PACMAN] Running 'pacman -Suy'
[2014-02-26 18:08] [PACMAN] synchronizing package lists
[2014-02-26 18:08] [PACMAN] starting full system upgrade
[2014-02-26 21:52] [PACMAN] Running 'pacman -Suy'
[2014-02-26 21:52] [PACMAN] synchronizing package lists
[2014-02-26 21:52] [PACMAN] starting full system upgrade
[2014-02-26 22:08] [PACMAN] upgraded grep (2.16-1 -> 2.18-1)
[2014-02-26 22:41] [PACMAN] Running 'pacman -S xchat'
[2014-02-26 22:41] [PACMAN] installed xchat (2.8.8-13)
[2014-02-27 00:02] [PACMAN] Running 'pacman -Suy'
[2014-02-27 00:02] [PACMAN] synchronizing package lists
[2014-02-27 00:02] [PACMAN] starting full system upgrade
[2014-02-27 01:41] [PACMAN] Running 'pacman -Suy'
[2014-02-27 01:41] [PACMAN] synchronizing package lists
[2014-02-27 01:41] [PACMAN] starting full system upgrade
[2014-02-27 12:20] [PACMAN] Running 'pacman -Suy'
[2014-02-27 12:20] [PACMAN] synchronizing package lists
[2014-02-27 12:20] [PACMAN] starting full system upgrade
[2014-02-27 12:26] [PACMAN] upgraded net-snmp (5.7.2-8 -> 5.7.2.1-1)
[2014-02-27 12:26] [PACMAN] upgraded youtube-dl (2014.02.25-1 -> 2014.02.26-1)
[2014-02-27 16:01] [PACMAN] Running 'pacman -Suy'
[2014-02-27 16:01] [PACMAN] synchronizing package lists
[2014-02-27 16:01] [PACMAN] starting full system upgrade
[2014-02-27 16:05] [PACMAN] upgraded wpa_supplicant (2.0-4 -> 2.1-3)
[2014-02-27 19:58] [PACMAN] Running 'pacman -Suy'
[2014-02-27 19:58] [PACMAN] synchronizing package lists
[2014-02-27 19:58] [PACMAN] starting full system upgrade
[2014-02-27 20:00] [PACMAN] Running 'pacman -S terminus'
[2014-02-27 20:00] [PACMAN] Running 'pacman -S terminus-font'
[2014-02-27 20:01] [PACMAN] installed terminus-font (4.38-4)
[2014-02-27 21:04] [PACMAN] Running 'pacman -Suy'
[2014-02-27 21:04] [PACMAN] synchronizing package lists
[2014-02-27 21:04] [PACMAN] starting full system upgrade
[2014-02-27 22:51] [PACMAN] Running 'pacman -Suy'
[2014-02-27 22:51] [PACMAN] synchronizing package lists
[2014-02-27 22:51] [PACMAN] starting full system upgrade
[2014-02-28 12:09] [PACMAN] Running 'pacman -Suy'
[2014-02-28 12:09] [PACMAN] synchronizing package lists
[2014-02-28 12:09] [PACMAN] starting full system upgrade
[2014-02-28 16:51] [PACMAN] Running 'pacman -Suy'
[2014-02-28 16:51] [PACMAN] synchronizing package lists
[2014-02-28 16:52] [PACMAN] starting full system upgrade
[2014-03-01 12:10] [PACMAN] Running 'pacman -S bluez'
[2014-03-01 12:19] [PACMAN] Running 'pacman -S xf86-input-joystick linuxconsole'
[2014-03-01 12:20] [PACMAN] installed xf86-input-joystick (1.6.2-3)
[2014-03-01 12:20] [PACMAN] installed linuxconsole (1.4.6-1)
[2014-03-01 12:21] [PACMAN] Running '/usr/bin/pacman -U /home/joaowojcikiewicz/z-aur/rejoystick/rejoystick-0.8.1-3-i686.pkg.tar.xz'
[2014-03-01 12:21] [PACMAN] installed rejoystick (0.8.1-3)
[2014-03-01 12:22] [PACMAN] Running '/usr/bin/pacman -U /home/joaowojcikiewicz/z-aur/joystick/joystick-20051019-12-i686.pkg.tar.xz'
[2014-03-01 12:48] [PACMAN] Running 'pacman -Suy'
[2014-03-01 12:48] [PACMAN] synchronizing package lists
[2014-03-01 12:48] [PACMAN] starting full system upgrade
[2014-03-01 12:49] [PACMAN] upgraded glibc (2.19-2 -> 2.19-3)
[2014-03-01 12:49] [PACMAN] upgraded device-mapper (2.02.105-1 -> 2.02.105-2)
[2014-03-01 12:49] [PACMAN] upgraded cryptsetup (1.6.3-2 -> 1.6.4-1)
[2014-03-01 12:49] [PACMAN] upgraded feh (2.9.3-1 -> 2.10-1)
[2014-03-01 12:49] [PACMAN] upgraded libtirpc (0.2.3-2 -> 0.2.4-1)
[2014-03-01 12:49] [PACMAN] upgraded readline (6.2.004-2 -> 6.3-1)
[2014-03-01 12:49] [PACMAN] upgraded lvm2 (2.02.105-1 -> 2.02.105-2)
[2014-03-01 12:49] [PACMAN] upgraded ppp (2.4.6-1 -> 2.4.6-2 -
Time capsule blinking amber and my wireless network has vanished after factory reset
Hello,
I have an Apple Macbook aluminum body with a Motorola cable modem hooked up to the Time Capsule which acts as my router. After turning the power off in my home, the internet has not been working. The light on the TC was green, but I had no internet because Airport had a "self-assigned" IP address and may not be able to connect to the internet. Then, I decided to do a hard reset and restore my setting to factory. The light on the TC is blinking amber. When I go into Airport Utility, it gives me this message: "Airport Utility was unable to find any Airport wireless devices". On top of all this, when I did the hard reset, my wifi network is not on the list of Airport networks in my range. It has completely disappeared. I have all the wires connected properly to the router and TC. Please help, this scenario is very frustrating.If you performed a factory default reset, the TC is now broadcasting a wireless network with a name like Apple Network xxxxxx, where the "x" could be either a letter or number.
You must first log on to this wireless network (there is no security or password) and establish a connection.
Then, if the TC was reset properly, you will be able to open AirPort Utility and re-configure the TC.
When you click Update to save your configuration settings, the TC will "dsiappear" from AirPort Utility. This is normal. Close AirPort Utility and wait for the TC to restart.
Then log on to the "new" wireless network that you named during the configuration. -
Unable to connect to Office Wireless Network (802.1x) after Windows Update
Hi, my notebooks are on Windows 7 Enterprise 64bit. We have only recently started Windows Updates.
We are on a Wireless network 802.1x.
In the past, we are able to do the following steps :
1. Open the "connections are available" window by clicking on the wireless icon (signal bars with yellow sun)
2. Right click on the desired network and choose properties
3. Change settings (eg. MEAP or use local Windows credentials etc)
4. Click connect to connect
Now, from the "connections are available" window, when we right click on the desired Network, only "connect" is shown.
In this case, I cannot connect to the network as the settings are wrong, if I cannot connect to the network how do I change the settings ?
Please kindly adviseHi,
I agree with britishdhez.
In addition, I would like to confirm which update caused this issue. Is it a driver update? I suggest installing driver update from the manufacturer's website.
You can also reinstall the wireless driver:
a. Click Start, type "devmgmt.msc" (without quotation marks) in the Search bar and press Enter.
b. Expand "Network adaptor".
c. Right click on your network card and then click Uninstall
d. Remove the driver software at the same time.
After that, restart the computer and reinstall the network card driver.
Meanwhile, you may run the Network troubleshooter to see if it can help diagnose and solve your problem:
Using the Network troubleshooter in Windows 7
http://windows.microsoft.com/en-sg/windows7/using-the-network-troubleshooter-in-windows-7
Also, please remove the wireless network profile for a test.
Delete a profile
At the command prompt ( Win+ R-->CMD ), type:
netsh wlan delete profile name="ProfileName"
For you reference: Netsh Commands for Wireless Local Area Network (wlan)
http://technet.microsoft.com/en-us/windows//aa905085.aspx
Hope it helps.
Regards,
Blair Deng
Blair Deng
TechNet Community Support -
Wireless network connectivity issues after upgrading to Snow Leopard
After upgrading to Snow Leopard (10.6.4) I find that my wireless network will not automatically connect to my router (Netgear DG834G) as it used to. First impressions are that the macbook is finding a number of wireless networks but wants to connect to the one that is alphabetically first in the list. It also seems that the signal that the airport is receiving is weak, even when the macbook is next to the router.
Has anyone experienced this when they upgraded?
Any and all help gratefully appreciated
Nickbut a couple that I used with no problem before I upgraded now give me a "server not found" error after I enter my login and password.
Quit Safari. Open Keychain Access /Applications/Utilities. Select Passwords on the left.
Delete the keychains for the sites you have problems logging into AND the Safari Forms Autofill keychain. Now from the menu bar click Keychain Access / Keychain First Aid. Select: Verify. If necessary, select: Repair. You will be prompted for your admin password. Click Start.
Relaunch Safari. Navigate to a site. Login with your user name and password. That will create a new keychain for you.
If you still have problems accessing sites, go to Safari / Preferences then select the Security tab. Click: Show Cookies. Delete all cookies or just the one's for the problematic sites. Now try logging into a site again.
Even though you upgraded to v10.6.7 make sure Safari is up to date. From the menu bar click Safari / About Safari. If it's a version prior to 5.0.5, click your Apple menu (top left in your screen) then click: Software Update...
And check Safari / Preferences - Extensions. Something there may be preventing you from accessing secure sites. If you have any extensions installed, turn that off, quit then relaunch Safari to test. -
On a wireless network test report, I get "The wireless radio is not functioning."
The printer is a Photosmart C309a all-in-one. I've used this printer for some time and did so wirelessly earlier today. Upon ordering a print job the printer failed to produce results. I ran a Network Configuration Page where it showed the printer to be offline with no Active Connection Type. I then ran a Wireless Network Test report and received the message: "The wireless radio is not functioning. Contact HP Support." IS THERE A FIX FOR THIS?
I reinstalled the printer software on my computer configuring it with a USB connection, in order to be able to use the printer. I was able to use it with the USB connection but would most definitely prefer a wireless connection. I also turned off the printer, router and computer and turned them on in the order outlined in the user's manual, but to no avail. This, of course, I did before reinstalling the software for a USB connection.Hi,
I afraid the error indicate an an hardware failure..
You may try using a wired ethernet cable as a workaround, the printer will need to be services in order to repair its wireless card.
You may find the details to contact HP support by selecting your region and following Technical Support after you buy:
http://www8.hp.com/us/en/contact-hp/ww-contact-us.html
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution -
IPhone network connections slowed after upgrading to IOS 5.1!!
My iPhone network connections (WiFi/4G) are extermely slow after performing the update to IOS 5.1! Speedtest.Net results over 4G = 0.15 Mpbs down and 0.05 Mpbs up ans that's will FULL bars! AT&T claims that there are no network issues in my area and they are not throttling my device. Even over WiFi it's taking FOREVER to download apps from the app store, etc... What is going on????
My WiFi connection works fine, but 4G from ATT gives in 0.15 mpbs download. I called up ATT several times, but they have no resolution to this problem. Everytime they ask me to reset my network connection. This is a big deal for me as I am most of the time on Cellular Data and I need to use iPhone for my work. I am thinking to roll back to iOS 5.0.1. What in this world could turn a 3G phone into a 4G phone just by a software upgrade? I just feel like I am down to a 1G phone. Apple please fix this asap and release a patch, else I may not be able to use this phone.
-
Wireless internet speeds slower after upgrading from 10/2 to 50/25?? Using olders revision Mi424WR.
We have been using the oldest version/revision of the Actiontec Mi424WR router provided by verizon for 3+ years. Recently we upgraded from an outdated 10/2 internet plan to our current 50/25 wireless plan. The speeds when wired are fantastic, but with wireless, on multiple computers the speed even right next to the router hovers at about 10mbps. I understand about the degradation and limit of wireless signals, but we should absolutely be getting higher download speeds than 10mbps(~1Mb/s). On our older 10/2 mbps plan our devices were receiving consistant download speeds of higher than we are getting now, maxing out at 1.6Mb/s usually. The only change that has been made recently is we reset the router to fatory settings, leading me to believe that wireless settings that were in place before are no longer there and throttling wireless speeds. I do not expect to get the full 50+ mbps speed that I am getting from wired, but I do expect my wireless speeds to be consistent with our upgraded plan(let alone slower than our massively slower old plan). Any thoughts or help would be greatly appreciated, thanks!
You should definetely get better speeds even with an older router, upto about 20 or so.
If that works for you, then it's probably just a little wireless interference.
you can change that in the router. open a browser, and go to http://192.168.1.1
user name is admin. and the password is most likely the serial number found on the service tag of your VZ router unless you changed it. Once you login succesfully, go to the top and hit wireless, then on the left basic security. then go to option 3 which is channel 1, 6 and 11 and are the only channels you should try.
So it will likely be set to auto, change it to 11 and put the check for keep settings even after reboot (Directly under the channel) and then hit apply. after you hit apply, test your connection out, if you notice a difference, leave it like that until the problem happens again, and if it happens again, go back into the router, and try channel 6, test it out. and then finally 1 if the first two don't work.
Also take a look at page 2 of Actiontec's Wireless PDF File. It gives you some idea's with regards to position and orientation of where the router sits and how it can best be positioned for maximum coverage.
http://support.actiontec.com/doc_files/MI424WR_Rev(all)_Wireless_Networking_Guide.pdf -
Networking: extend wireless network Apple Time Capsule to cisco DOCSIS 3.0 cable modem
How should I connect a Time Capsule (4th gen) to a Cisco DOCSIS 3.0 that came with xfinity service to create a wireless extension to network... any special settings???
Should I use the Cisco or TC for the DHCP controller?You cannot wireless extend a network using TC.. Apple designed it to only work with other Apple products.. this is not that unusual.. but it is important .. you cannot do what you want.
One network .. one router. Keep the cisco as the main router and plug in the TC by ethernet and bridge it.. that is router bridge not wireless bridge .. you will find the control in the NAT and DHCP section of Lion
Or download the vastly superior older version of the utility here.
http://support.apple.com/kb/DL1482 -
Wireless Network has "disappeared" after Leopard installation
We have 2 Macs, my MacPro (connected by wire to ADSL) and an iMac (connecting to my wireless router to the same ADSL line). The iMac uses Airport to reach my wireless router, connecting to "Joe's Network." (MacPro --> D-Link Modem --> D-Link Wireless Router --> iMac Airport) This has worked fine for about 2 years.
After installing Leopard yesterday, the iMac does not show "Joe's Network," and I don't know how to restore it. Other networks in the neighborhood show up in the iMac's Airport listing, and the unsecured ones CAN be connected to. This indicates to me that there is nothing wrong with the iMac. I unplugged and replugged the modem and router on my MacPro, but nothing is working.
Can someone point me in the right direction?Ahh, welcome to the wonderful world of wifi under Leopard. Maybe you weren't aware that tens of thousands of people have been having endless problems with wifi whilst using Leopard .... I just got back from holiday - full signal yet no internet. Connect using ethernet and there it is - working perfectly. The culprit? Apple's very own Airport extreme base station, the new one which I bought thinking my old one was on the blink - nope.
Meanwhile Apple have not said a word about this in the last 8-10 weeks of utter misery for countless people - not a sausage. Many people are counting on 10.5.2 fixing this. I say don't count on it. Remember to complain to Apple as it is their own software/hardware that is at fault here. Meanwhile, they introduce a ... wifi laptop.... ooh the irony. -
Trouble connecting to wireless networks and slow connection.
For the past three weeks or so I've been experience difficulty connecting to networks I previously had no trouble connecting to. I'm only able to go about 15 feet or so away from a wireless router before my speed either drops through to the floor or the connection is lost entirely. I've tried looking through forums all over the internet, but I wondered if anybody had any insight into what I could do to get my wi-fi back up to speed?
Thanks!Try the steps in the blog post How I fixed my dropping wireless Airport connection problem in Snow Leopard to see if any of them help.
Good Luck.
Maybe you are looking for
-
Dear Expert, How to do automatically Goods Receipt that we no need to go to open screen Goods Receipt to processing. My concept is like we make sale order and system make automatically Purchase Order that we no need go to open that screen. I need to
-
How do i share my itunes account with a second computer
how do i share my itunes account with another computer in my home?
-
I can find no help on this, it says it cant print file, I have tried 3 printers. I have had this program over a year with no problems.
-
NON SEARCH FUNCTION ON OLDER 5G IS A DISGRACE....
APPLE NEED TO LOOK INTO THIS AS A LOT OF PEOPLE ARE GONNA BE ****** OFF ABOUT IT.............
-
Metadata included in HTML Gallery
All of the sudden metadata is included with the file name in a HTML Gallery. When you sellect the cell and open the larger file in addition to the file name, all the metadata is shown. This ha never occured until now and I can't for the life of me fi