WLC 2500 AP discovery problem
Hi,
I have successfully connected my WLC 2500 controller with 20 light weight Access points 1262N.
I have used the internal DHCP server option in the controller for the AP's and client.
Port 1 of the WLC is trunked with the switch 2960. All is working fine
The problem comes when I remove the Ethernet cable from the management interface and restart the WLC. The AP's don't come back. If I don't restart the WLC the AP's remain.
On the other hand, when I leave the Ethernet cable connected to the management port with my pc and then reboot the WLC, the AP's appear.
Seems like whenever im not physically connected to the management port of the WLC and restart it, the AP's don't come back. The only way to make them come back again is to connect my PC to the management port.
Please help me. What seems to be the problem here ?
Best Regards,
Hi,
All 20 Pc;s are in one area connected to the same AP im assuming. The PC;s are stationary, so didnt check for roaming, but generally my laptop connectivity is fine while roaming. It rarely disconnects but users have complained that it did disconncect a few times.
Please see below the WLC configuration:
User:Dawaa
Password:********
(Cisco Controller) >sh
(Cisco Controller) show>running-config
Notice: "show running-config" has been changed to be an alias to "show run-config".
Use "show run-config commands" to display the configuration commands.
Press Enter to continue or to abort...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 2500 Series Wireless LAN Controller"
PID: AIR-CT2504-K9, VID: V01, SN: PSZ163602PD
Burned-in MAC Address............................ 20:3A:07:67:C3:00
Maximum number of APs supported.................. 15
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.3.101.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... tEthernet0
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.0.140
Last Reset....................................... Software reset
System Up Time................................... 0 days 1 hrs 23 mins 40 secs
System Timezone Location......................... (GMT +3:00) Baghdad
Configured Country............................... SA - Saudi Arabia
Operating Environment............................ Commercial (0 to 40 C)
--More or (q)uit current module or to abort
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +30 C
Fan Status....................................... 4200 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 10
Burned-in MAC Address............................ 20:3A:07:67:C3:00
Maximum number of APs supported.................. 15
Press Enter to continue or to abort
AP Bundle Information
Primary AP Image Size
ap1g2 10596
ap3g1 11088
ap3g2 10968
ap801 7092
ap802 8428
c1130 5072
c1140 9288
c1250 6784
c1520 7852
c602i 3736
Secondary AP Image Size
ap1g2 10596
ap3g1 11088
ap3g2 10968
ap801 7092
ap802 8428
--More or (q)uit current module or to abort
c1130 5072
c1140 9288
c1250 6784
c1520 7852
c602i 3736
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or to abort
Network Information
RF-Network Name............................. Dawaa
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Multicast Address : 239.60.60.60
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
--More or (q)uit current module or to abort
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Enable
Mgmt Via Dynamic Interface.................. Enable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Forw Enable Auto 1000 Full Up Enable N/A
2 Normal Disa Enable Auto Auto Down Enable N/A
3 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 14
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP6c20.56a0.b352 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:52 default location 1 SA 1
AP6c20.5666.e34a 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:4a default location 1 SA 1
AP6c20.56a0.b341 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:41 default location 1 SA 1
AP6c20.56a0.b4db_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:db Expiry Warehouse 1 SA 1
AP6c20.569a.59da 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:da default location 1 SA 1
AP6c20.5666.e2db 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:db default location 1 SA 1
AP6c20.568c.d530_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d5:30 default location 1 SA 1
AP6c20.5666.e2ca 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:ca default location 1 SA 1
AP6c20.5666.e354 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:54 default location 1 SA 1
AP6c20.569a.59fd 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:fd default location 1 SA 1
AP6c20.56a0.b346 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:46 default location 1 SA 1
AP6c20.56a0.b2f0 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b2:f0 default location 1 SA 1
AP6c20.568c.d1ec 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d1:ec default location 1 SA 1
AP6c20.56a0.b425 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:25 default location 1 SA 1
--More or (q)uit current module or to abort
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
AP6c20.56a0.b352 disabled -
AP6c20.5666.e34a disabled -
AP6c20.56a0.b341 disabled -
AP6c20.56a0.b4db_(Expiry) disabled -
AP6c20.569a.59da disabled -
AP6c20.5666.e2db disabled -
AP6c20.568c.d530_(Expiry) disabled -
AP6c20.5666.e2ca disabled -
AP6c20.5666.e354 disabled -
AP6c20.569a.59fd disabled -
AP6c20.56a0.b346 disabled -
AP6c20.56a0.b2f0 disabled -
AP6c20.568c.d1ec disabled -
AP6c20.56a0.b425 disabled -
Press Enter to continue or to abort
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description.................................
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band.....................................
5 GHz band.......................................
WLAN ID Interface Network Admission Control Radio Policy
1 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP6c20.56a0.b352 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:52 default location 1 SA 1
AP6c20.5666.e34a 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:4a default location 1 SA 1
AP6c20.56a0.b341 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:41 default location 1 SA 1
AP6c20.56a0.b4db_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:db Expiry Warehouse 1 SA 1
--More or (q)uit current module or to abort
AP6c20.569a.59da 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:da default location 1 SA 1
AP6c20.5666.e2db 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:db default location 1 SA 1
AP6c20.568c.d530_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d5:30 default location 1 SA 1
AP6c20.5666.e2ca 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:ca default location 1 SA 1
AP6c20.5666.e354 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:54 default location 1 SA 1
AP6c20.569a.59fd 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:fd default location 1 SA 1
AP6c20.56a0.b346 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:46 default location 1 SA 1
AP6c20.56a0.b2f0 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b2:f0 default location 1 SA 1
AP6c20.568c.d1ec 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d1:ec default location 1 SA 1
AP6c20.56a0.b425 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:25 default location 1 SA 1
Press Enter to continue or to abort
RF Profile
Number of RF Profiles............................ 0
Out Of Box State................................. Disabled
RF Profile Name Band Description Applied
Press Enter to continue or to abort
AP Config
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP6c20.56a0.b352
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:a0:b3:52
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.111
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
--More or (q)uit current module or to abort
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
--More or (q)uit current module or to abort
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z0A6
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 01 m 44 s
AP LWAPP Up Time................................. 0 days, 01 h 25 m 37 s
Join Date and Time............................... Wed Mar 13 16:10:25 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
--More or (q)uit current module or to abort
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:7a:20
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
--More or (q)uit current module or to abort
MCS 11................................... DISABLED
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
--More or (q)uit current module or to abort
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 3
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
Extension Channel ......................... NONE
--More or (q)uit current module or to abort
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP6c20.56a0.b352
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
--More or (q)uit current module or to abort
MAC Address...................................... 6c:20:56:a0:b3:52
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.111
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
--More or (q)uit current module or to abort
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z0A6
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or to abort
AP Up Time....................................... 0 days, 22 h 01 m 44 s
AP LWAPP Up Time................................. 0 days, 01 h 25 m 37 s
Join Date and Time............................... Wed Mar 13 16:10:25 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211n-5
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:7a:20
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... DISABLED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
--More or (q)uit current module or to abort
MCS 15................................... SUPPORTED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
--More or (q)uit current module or to abort
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
--More or (q)uit current module or to abort
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
--More or (q)uit current module or to abort
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Press Enter to continue or to abort
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP6c20.5666.e34a
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:66:e3:4a
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.39
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
--More or (q)uit current module or to abort
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09V
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 03 m 17 s
AP LWAPP Up Time................................. 0 days, 01 h 28 m 23 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 04 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
--More or (q)uit current module or to abort
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 54:78:1a:f2:51:c0
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
MCS 11................................... DISABLED
--More or (q)uit current module or to abort
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
--More or (q)uit current module or to abort
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 2
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
--More or (q)uit current module or to abort
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP6c20.5666.e34a
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:66:e3:4a
--More or (q)uit current module or to abort
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.39
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
--More or (q)uit current module or to abort
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09V
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 03 m 17 s
--More or (q)uit current module or to abort
AP LWAPP Up Time................................. 0 days, 01 h 28 m 23 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 04 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211n-5
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 54:78:1a:f2:51:c0
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... SUPPORTED
--More or (q)uit current module or to abort
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... DISABLED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
--More or (q)uit current module or to abort
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 64
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
--More or (q)uit current module or to abort
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
--More or (q)uit current module or to abort
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Press Enter to continue or to abort
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP6c20.56a0.b341
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:a0:b3:41
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.120
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
--More or (q)uit current module or to abort
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09Y
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 07 m 08 s
AP LWAPP Up Time................................. 0 days, 01 h 31 m 05 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
--More or (q)uit current module or to abort
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:81:f0
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
MCS 11................................... DISABLED
--More or (q)uit current module or to abort
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ..............
Similar Messages
-
Hi,
I have WLC 2500 with firmware 7.4.121.0. Problem is with multicasting (or media streaming). One big boss wants his camera communicate with tablet, ant this communication requires multicast.
In MONITOR-> Multicast I can devices trying to communicate but nothing happens. I found some guides how to configure multicast for video or voice, but I have no luck with them.
Perhaps someone had luck with such configuration?
Thanks.Hi
See whether below helps (these are with wlc 7.0 code, but I think not much differences in 7.4 compare to 7.0). Refer specific configuration guide for exact syntax
http://mrncciew.com/2012/12/24/understanding-videostream-feature/
http://mrncciew.com/2012/11/17/configuring-multicast-on-wlc/
Make sure your wired network also support multicast.
HTH
Rasika
*** Pls rate all useful responses **** -
Cisco WLC 2500 - 802.1x with Vasco Radius SMS OTP
Hello folks,
I have what seems to be a complex implementation with many things that need to be done on a customers network and I wanted to be pointed in the right direction.
The current scenario is such, the customer has a Cisco WLC 2500 device that has 3 access points(these are in the same AP group) connected to it. There is one SSID that I will call PRODUCTION here that some domain users use to connect to the local network. The customer has requested to have a GUEST SSID added to the WLC where guest users will connect to and recieve a SMS OTP for authentication.
Correct me if I am wrong, but I will obviously need to segment the SSIDs to have them running on different subnets to ensure that guest users do not have access to the production network once they authenticate. In order to do this I will need to configure Dynamic VLAN assignment for the Cisco WLC and connect it to a 802.1x port on the switch.
Now what is not clear is I am not interested in authenticating the users that connect via "Production SSID" and want to bypass authentication for those users and have them assigned to the default vlan (or maybe perhaps have them authenticate via LDAP on the AD), however I want to force the "GUEST" SSID users to authenticate so that they may recieve an SMS OTP (reason for this is to force guests to register their phone numbers to use the internet so that Illegal activity may be tracked).
1)So would it be possible to bypass authentication(or authenticate them via LDAP) for the PRODUCTION SSID as only domain users would know the SSID password to log on and have them by default assigned to the production subnet (default vlan) but force the GUEST SSID users to another VLAN via 802.1x sms otp?
2)*Important* Another issue that is not clear is will I be able to directly configure AAA Radius settings on the Cisco WLC to directly authenticate with the VASCO Radius OTP and recieve a challenge-response(required for OTP) during authentication? As I have seen from Ciscos Dynamic VLAN assignment docuementation (http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml) additional IETF Radius Perimeters are used such as Tunnel-Private-Group-ID etc are used which I can't seem to configure on the Vasco.
I do beileve this is a great project in helping me understand the INs and OUTs of CISCO WLC as well as Wireless NAC, If anyone could enlighten me and point me in the right direction I would be forever in debt. Much appreciated.
Best Regards
Sinan Barghouthi - JNCIA-FWV , JNCIA-IDP , CCA-NS , TCSM-8.0On your WLAN you can enable AES and TKIP. Just know that some clients mau have issue when they see both TKIP and AES. Ive had pretty good success with this in the past. Dont forget, you also need to enable WMM allowed to get N rates.
But you will need to configure AES on the client as well to support N rates.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection." -
Identity Services Engine (ISE) support for the WLC 2500
Is the ISE going to support the 2500 series Wireless LAN Controller WLC? If yes in what release and appriximately when is that due to be released?
Your question is disturbing. ISE is (amongst other things) a radius server. WLC 2500 can use radius servers for authentication. So it's supported.
Any device doing radius is supported with ISE ...
Now you are maybe referring to a particular feature in ISE ? -
hello
i have a question about a cisco wlc 2500.
when you configure a interface on the controller, you can set a ip address
mask en DHCP server address but also you can set the interface as a AP-Manager
why is this?
thanksOn the old WLC models like 2100, 2006,4400 we had to configure the management interface for managing the WLC and the AP manager so that the APs could create the LWAPP or CAPWAP tunnel to the WLC.
On the new model of WLCs like the 2500,5508 the AP manager interface is not required, the management interface if it has the check for dynamic interface it will work at the same time as the AP manager interface.
Here is the link where you can check on how to deploy the 2504 WLC and the different setups to use with several AP managers.
http://www.cisco.com/en/US/products/ps11630/products_tech_note09186a0080b8450c.shtml -
Splash Page in WLC 2500 Series
Can someone tell me if there is Splash Page feature in the 2500 WLC ? I cannot find any Cisco document which says it has that feature ?
Yes, Its available.
Here is a link that points to a configuration guide for a wlc 2500, 7.5.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/config_guide/b_cg75.pdf
"The splash page web redirect feature is available only for WLANs that are configured for 802.1X or
WPA+WPA2 Layer 2 security with 802.1x key management." -
Problèmes d'ajout de licences sur un controller WLC 2500
Bonjour,
Je possède un Cisco WLC 2500 controller pour mes bornes Wifi.
Sur ce controller j'ai déjà un pack de 25 licences d'installées.
Récemment j'ai acheté un nouveau pack de licence et il met impossible de l'ajouter correctement.
j’effectue la procédure suivante :
Je clique dans l'onglet "management" puis sur "software activation"
Je clique sur "commandes"
Je sélectionne "install licences"
ce que j'obtiens
ensuite je reboot le controller, mais les licences ne sont pas présente dans la liste.
Avez-vous une idée ?
Merci d'avanceGREP peut servir à deux choses : un enrichissement automatique via les styles GREP ou un rechercher-remplacer. Les styles GREP ne font qu'enrichir du texte existant mais n'ont pas pour fonction d'ajouter du texte. Pour ce que tu cherches à faire (un ajout), la syntaxe proposée dans le livre doit donc être utilisée dans la boîte de dialogue « rechercher-remplacer ».
-
3702i AP's not Joining WLC - Layer 3 discovery request not received on management VLAN
Hi Guys,
This is a follow up post to this thread: https://supportforums.cisco.com/discussion/12400481/3702i-not-joint-2504
Have been playing around with my AP's and made sure the time is correct on all the devices ( WLC and Switch). I have also moved the AP's to the same Vlan as the management IP of the WLC.
if I move the AP's to the same Vlan as the WLC they join and are happy, as soon as I move them to a different Vlan they cant join and there time goes back to the default plus they do not seem to save the WLC details to flash but still remember the test names I give them.
it appears that option 43 is working fine as I can see it look for the WLC IP and I have done some trouble shooting on the WLC and it looks like it see's the AP but doesn't except it.
please see below for the boot up of the AP and the WLC logs:
AP
IIOS Bootloader - Starting system.
*** deleted for breverity *****
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
*** deleted for breverity *****
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
*** deleted for breverity *****
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
WLC:
isco Controller) >show time
Time............................................. Tue Jan 27 17:44:47 2015
Timezone delta................................... 0:0
Timezone location................................ (GMT +8:00) HongKong, Bejing, Chongquing
NTP Servers
NTP Polling Interval......................... 3600
Index NTP Key Index NTP Server NTP Msg Auth Status
1 0 150.101.176.226 AUTH DISABLED
(Cisco Controller) >show ap join stats summary
Incorrect input! Use 'show ap join stats summary [all/<ap-mac>]'
(Cisco Controller) >show ap join stats summary all
Number of APs.............................................. 2
Base Mac AP EthernetMac AP Name IP Address Status
f4:4e:05:aa:a6:a0 f4:4e:05:94:c3:98 APf44e.0594.c398 10.1.1.22 Joined
f4:4e:05:b6:ce:f0 N A Test_1 10.1.20.7 Not Joined
(Cisco Controller) >show ap join stats detailed f4:4e:05:b6:ce:f0
Sync phase statistics
- Time at sync request received............................ Not applicable
- Time at sync completed................................... Not applicable
Discovery phase statistics
- Discovery requests received.............................. 45
- Successful discovery responses sent...................... 21
- Unsuccessful discovery request processing................ 24
- Reason for last unsuccessful discovery attempt........... Layer 3 discovery request not received on management VLAN
- Time at last successful discovery attempt................ Jan 27 17:45:49.705
- Time at last unsuccessful discovery attempt.............. Jan 27 17:45:49.705
Join phase statistics
- Join requests received................................... 0
- Successful join responses sent........................... 0
- Unsuccessful join request processing..................... 0
- Reason for last unsuccessful join attempt................ Not applicable
- Time at last successful join attempt..................... Not applicable
- Time at last unsuccessful join attempt................... Not applicable
Configuration phase statistics
--More-- or (q)uit
- Configuration requests received.......................... 0
- Successful configuration responses sent.................. 0
- Unsuccessful configuration request processing............ 0
- Reason for last unsuccessful configuration attempt....... Not applicable
- Time at last successful configuration attempt............ Not applicable
- Time at last unsuccessful configuration attempt.......... Not applicable
Last AP message decryption failure details
- Reason for last message decryption failure............... Not applicable
Last AP disconnect details
- Reason for last AP connection failure.................... Not applicable
- Last AP disconnect reason................................ Not applicable
Last join error summary
- Type of error that occurred last......................... Lwapp discovery request rejected
- Reason for error that occurred last...................... Layer 3 discovery request not received on management VLAN
- Time at which the last join error occurred............... Jan 27 17:45:49.705
AP disconnect details
- Reason for last AP connection failure.................... Not applicable
Ethernet Mac : 00:00:00:00:00:00 Ip Address : 10.1.20.7
(Cisco Controller) >show interface summary
Number of Interfaces.......................... 4
Interface Name Port Vlan Id IP Address Type Ap Mgr Guest
ap LAG 20 10.1.20.231 Dynamic No No
guest LAG 30 10.1.30.231 Dynamic No No
management LAG 10 10.1.1.231 Static Yes No
virtual N/A N/A 1.1.1.1 Static No No
SWITCH
witch#show run
Building configuration...
*** deleted for breverity *****
no aaa new-model
clock timezone AWST 8
system mtu routing 1500
ip routing
ip dhcp pool WAP_Pool
network 10.1.20.0 255.255.255.0
default-router 10.1.20.1
option 43 hex f104.0a01.01e7
ip dhcp pool Clients
network 10.1.30.0 255.255.255.0
default-router 10.1.30.1
dns-server 203.0.178.191
ip dhcp pool test
network 10.1.1.0 255.255.255.0
default-router 10.1.1.1
crypto pki trustpoint TP-self-signed-4082587776
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-4082587776
revocation-check none
rsakeypair TP-self-signed-4082587776
*** deleted for breverity *****
*** deleted for breverity ***** !
interface FastEthernet0/3
description *** WLC ****
switchport trunk encapsulation dot1q
switchport mode trunk
interface FastEthernet0/4
description **** AP *****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/5
description **** AP ****
switchport access vlan 20
switchport mode access
spanning-tree portfast
interface FastEthernet0/6
i*** deleted for breverity ***** !
interface Vlan10
description *** Managment ***
ip address 10.1.1.230 255.255.255.0
interface Vlan20
description *** WIRELESS APS ***
ip address 10.1.20.1 255.255.255.0
interface Vlan30
ip address 10.1.30.1 255.255.255.0
ip classless
ip route 0.0.0.0 0.0.0.0 10.1.1.1
ip http server
ip http secure-server
ip sla enable reaction-alerts
l*** deleted for breverity *****
ntp clock-period 36028827
ntp source FastEthernet0/1
ntp server 121.0.0.42
ntp server 202.127.210.37
end
I have also placed a Device in Vlan 20 and it is able to ping the WLC and the WLC can ping it s routing is working.
ThanksHey Scott,
I gave that a shot and still no luck, log's from AP boot up:
IIOS Bootloader - Starting system.
flash is writable
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 20 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Ethernet speed is 100 Mb - FULL Duplex
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1"...#########################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-mx.153-3.JA1" uncompressed and installed, entry point: 0x2003000
executing...
Secondary Bootloader - Starting system.
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Xmodem file system is available.
flashfs[0]: 67 files, 9 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 41158656
flashfs[0]: Bytes used: 20894208
flashfs[0]: Bytes available: 20264448
flashfs[0]: flashfs fsck took 21 seconds.
flashfs[1]: 0 files, 1 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 12257280
flashfs[1]: Bytes used: 1024
flashfs[1]: Bytes available: 12256256
flashfs[1]: flashfs fsck took 1 seconds.
Base Ethernet MAC address: f4:4e:05:b7:1e:84
Boot CMD: 'boot flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1;flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1'
Loading "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1"...###############################################
File "flash:/ap3g2-k9w8-mx.153-3.JA1/ap3g2-k9w8-xx.153-3.JA1" uncompressed and installed, entry point: 0x1003000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
Montserrat Board
40MB format
Tide XL MB - 40MB of flash
Initializing flashfs...
flashfs[2]: 67 files, 9 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 40900608
flashfs[2]: Bytes used: 20894208
flashfs[2]: Bytes available: 20006400
flashfs[2]: flashfs fsck took 14 seconds.
flashfs[2]: Initialization complete.
flashfs[4]: 0 files, 1 directories
flashfs[4]: 0 orphaned files, 0 orphaned directories
flashfs[4]: Total bytes: 11999232
flashfs[4]: Bytes used: 1024
flashfs[4]: Bytes available: 11998208
flashfs[4]: flashfs fsck took 0 seconds.
flashfs[4]: Initialization complete.
Copying radio files from flash: to ram:
Copy in progress...CCCCC
Copy in progress...CCC
Copy in progress...CCCC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCC
Copy in progress...CC
Copy in progress...CCCCC
Copy in progress...CCCC
Copy in progress...CC
Uncompressing radio files...
...done Initializing flashfs.
Radio0 present 8764 8000 0 A8000000 A8010000 0
Rate table has 650 entries (20 legacy/224 11n/406 11ac)
POWER TABLE FILENAME = ram:/Q2.bin
Radio1 present 8864 8000 0 80000000 80100000 4
POWER TABLE FILENAME = ram:/Q5.bin
Radio2 not present 0 0 0 0 0 8
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP3702I-Z-K9 (PowerPC) processor (revision A0) with 376810K/134656K bytes of memory.
Processor board ID FGL1838X4T1
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 8.0.110.0
1 Gigabit Ethernet interface
2 802.11 Radios
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: F4:4E:05:B7:1E:84
Part Number : 73-15243-01
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC18343WPR
Top Assembly Part Number : 068-05054-03
Top Assembly Serial Number : FGL1838X4T1
Top Revision Number : A0
Product/Model Number : AIR-CAP3702I-Z-K9
% Please define a domain-name first.
Press RETURN to get started!
*Mar 1 00:00:19.295: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed (15)
*Mar 1 00:00:19.755: Registering HW DTLS
*Mar 1 00:00:19.763: APAVC: Initial WLAN Buffers Given to System is 2500
*Mar 1 00:00:19.815: APAVC: WlanPAKs 42878 RadioPaks 42270
*Mar 1 00:00:22.127: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:26.055: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0 (4)
*Mar 1 00:00:26.167: Loading Power Tables from ram:/Q2.bin. Class = A
*Mar 1 00:00:26.167: record size of 3ss: 1168 read_ptr: 4F9698E
*Mar 1 00:00:31.207: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1 (4)
*Mar 1 00:00:31.251: Loading Power Tables from ram:/Q5.bin. Class = Z
*Mar 1 00:00:31.251: record size of vht: 2904 read_ptr: 4F9698E
*Mar 1 00:00:31.407: Wait until the stile protocol list is initialized.
*Mar 1 00:00:32.651: Start STILE Activation
*Mar 1 00:00:34.571: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 00:00:35.447: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C3700 Software (AP3G2-K9W8-M), Version 15.3(3)JA1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Fri 19-Dec-14 11:20 by prod_rel_team
*Mar 1 00:00:35.447: %SNMP-5-COLDSTART: SNMP agent on host Test_1 is undergoing a cold start
*Mar 1 00:00:36.563: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:37.787: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to uplwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:37.939: %SSH-5-ENABLED: SSH 2.0 has been enabled
*Mar 1 00:00:37.939: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:00:38.987: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:00:47.567: %LINK-6-UPDOWN: Interface BVI1, changed state to down
*Mar 1 00:00:48.567: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to down
*Mar 1 00:00:50.431: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed (2-16)
*Mar 1 00:00:50.431: DPAA Initialization Complete
*Mar 1 00:00:50.431: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
*Mar 1 00:00:51.431: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:53.435: %LINK-6-UPDOWN: Interface BVI1, changed state to up
*Mar 1 00:00:53.867: Currently running a Release Image
*Mar 1 00:00:54.287: Incorrect certificate in SHA2 PB !
*Mar 1 00:00:54.287: Using SHA-1 signed certificate for image signing validation.
*Mar 1 00:00:54.575: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:59.787: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.2, mask 255.255.255.0, hostname Test_1
*Mar 1 00:01:02.707: APAVC: Succeeded to activate all the STILE protocols.
*Mar 1 00:01:02.707: APAVC: Registering with CFT
*Mar 1 00:01:02.707: APAVC: CFT registration of delete callback succeeded
*Mar 1 00:01:02.707: APAVC: Reattaching Original Buffer pool for system use
*Mar 1 00:01:02.707: Pool-ReAtach: paks 42878 radio42270
%Default route without gateway, if not a point-to-point interface, may impact performance
*Mar 1 00:01:10.103: AP image integrity check PASSED
*Mar 1 00:01:10.187: Incorrect certificate in SHA2 PB !
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:01:10.203: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:01:11.591: %CDP_PD-4-POWER_OK: 15.4 W power - NEGOTIATED inline power source
*Mar 1 00:01:12.691: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.691: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:01:13.947: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:01:14.947: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:20.211: %SYS-6-LOGGINGHOST_STARTSTOP: Logging to host 255.255.255.255 port 514 CLI Request Triggered
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:31.215: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
*Mar 1 00:02:11.599: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:02:11.603: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Mar 1 00:02:11.611: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:02:12.603: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 00:02:12.639: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:02:12.647: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Mar 1 00:02:12.655: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:02:13.639: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:02:13.647: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 00:02:13.699: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:02:14.699: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
Not in Bound state.
*Mar 1 00:02:44.719: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:02:49.839: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.3, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:02:55.719: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP
Not in Bound state.
*Mar 1 00:03:59.219: %CAPWAP-3-DHCP_RENEW: Could not discover WLC. Either IP address is not assigned or assigned IP is wrong. Renewing DHCP IP.
*Mar 1 00:04:04.343: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.20.4, mask 255.255.255.0, hostname Test_1
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:04:10.223: %CAPWAP-5-DHCP_OPTION_43: Controller address 10.1.1.231 obtained through DHCP -
WLC 2500 pierde lista de MAC Address luego que se va la energía eléctrica
Saludos, tengo un problema con un Cisco 2500 Wireless Controller, tengo activada el MAC Filtering y tiene una lista de MAC address, pero cada vez que se va la energía eléctrica se pierde la clave de acceso a la red wireless, la activación del MAC Filtering y la lista, lo que me olbiga a definir nuevamente la clave de acceso a la red wireless, marcar el cuadro de la opción MAC Filtering y a ingresar toda la lista de MAC address, alguna idea de como evitar que me suceda esto?.... el resto de la configuración permanece intacta, gracias por su ayuda.
Hola Walter.
Lo que trata de decir Scott es que ese comportamiento en el WLC no es normal,por lo cual te aconseja abrir un caso al TAC de cisco.
I'm a native spanish Speaker -
I am currently setting up a 4402 controller and lwapps. Our wireless right now is all managed by corp and is a combination of autonomous and lwapp. Here is my problem.
I have setup option43 in my dhcp scope. When I connect a fresh radio to the same subnet as the controller I see that the radio goes to the controller but then there is a message and the radio goes to the corp controller.
Here is the boot log from a new radio.
%LWAPP-3-CLIENTEVENTLOG: Controller address 10.200.190.10(MINE) obtained through DHCP
%LWAPP-3-CLIENTEVENTLOG: Did not get log server settings from DHCP.
%LWAPP-3-CLIENTEVENTLOG: Performing DNS resolution for CISCO-LWAPP-CONTROLLER.gtna.gt.ds
%LWAPP-3-CLIENTEVENTLOG: Controller address 10.148.198.7(CORP) obtained through DNS
I see that message about a log server. Did I miss something?
thanks
tonyHi Guys,
I just thought that I would link this info for the LWAPP Layer 3 startup. +5 points for both Wesley and Leo for your ongoing great work here :)
The LWAPP AP goes through this process on startup for Layer 3 mode:
The LAP boots and DHCPs an IP address if it was not previously assigned a static IP address.
The LAP sends discovery requests to controllers through the various discovery algorithms and builds a controller list. Essentially, the LAP learns as many management interface addresses for the controller list as possible via:
DHCP option 43 (good for global companies where offices and controllers are on different continents)
DNS entry for âcisco-lwapp-controllerâ (good for local businesses - can also be used to find where brand new APs join)
Management IP addresses of controllers the LAP remembers previously
A Layer 3 broadcast on the subnet
Over the air provisioning
Statically configured information
From this list, the easiest method to use for deployment is to have the LAPs on the same subnet as the management interface of the controller and allow the LAP's Layer 3 broadcast to find the controller. This method should be used for companies that have a small network and do not own a local DNS server.
The next easiest method of deployment is to use a DNS entry with DHCP. You can have multiple entries of the same DNS name. This allows the LAP to discover multiple controllers. This method should be used by companies that have all of their controllers in a single location and own a local DNS server. Or, if the company has multiple DNS suffixes and the controllers are segregated by suffix.
DHCP option 43 is used by large companies to localize the information via the DHCP. This method is used by large enterprises that have a single DNS suffix. For example, Cisco owns buildings in Europe, Australia, and the United States. In order to ensure that the LAPs only join controllers locally, Cisco cannot use a DNS entry and must use DHCP option 43 information to tell the LAPs what the management IP address of their local controller is.
Finally, static configuration is used for a network that does not have a DHCP server.You can statically configure the information necessary to join a controller via the console port and the AP's CLI. For information on how to statically configure controller information using the AP CLI, refer to Manually Configuring Controller Information Using the Access Point CLI.
For a detailed explanation on the different discovery algorithms that LAPs use to find controllers, refer to LAP Registration with WLC.
For information on configuring DHCP option 43 on a DHCP server, refer to DHCP OPTION 43 for Lightweight Cisco Aironet Access Points Configuration Example.
Send a discovery request to every controller on the list and wait for the controller's discovery reply which contains the system name, AP-manager IP addresses, the number of APs already attached to each AP-manager interface, and overall excess capacity for the controller.
Look at the controller list and send a join request to a controller in this order (only if the AP received a discovery reply from it):
Primary Controller system name (previously configured on LAP)
Secondary Controller system name (previously configured on LAP)
Tertiary Controller system name (previously configured on LAP)
Master controller (if the LAP has not been previously configured with any Primary, Secondary, or Tertiary controller names. Used to always know which controller brand new LAPs join)
....continued on next page -
Can't get radio measurements on WLC 2500 to work
Hi all,
I have 2 lightweight APs (AIR-CAP1602I-E-K9) connected to a wireless lan controller 2500. I am trying to enable radio measurements, however after configuring the WLC, RM status is still reported as disabled. I used this document http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_010000111.html#ID2037 to configure the WLC.
Here is my current config:
1. CCX-Lite is enabled
> show run-config
CCX-lite status ............................ Enabled
2. AeronetIESupport for the wlan of interest is enabled
> show wlan 14
CCX - AironetIe Support.......................... Enabled
3. RM is enabled globally
> show advanced 802.11a ccx global
802.11a Client Beacon Measurements:
enabled with (interval=60) seconds
4. RM is enabled for the AP
> show advanced 802.11a ccx ap AP_1
802.11a Client Beacon Measurements for Cisco AP:
enabled with (interval=60) seconds
However, when requesting the RM status on the controller, every type of measurement is shown as disabled:
> show ap ccx rm AP_1 status
B Radio
Beacon Request................................. Disabled
Channel Load Request........................... Disabled
Frame Request.................................. Disabled
Noise Histogram Request........................ Disabled
Path Loss Request.............................. Disabled
Interval....................................... 60
Iteration...................................... 0
A Radio
Beacon Request................................. Disabled
Channel Load Request........................... Disabled
Frame Request.................................. Disabled
Noise Histogram Request........................ Disabled
Path Loss Request.............................. Disabled
Interval....................................... 60
Iteration...................................... 0
When checking the client RM status, I get the following results:
> show client ccx rm Client_MAC status
Client not in the unicast rm list
> show client ccx rm Client_MAC report beacon
Client not configured for ccx rm
> show client detail Client_MAC
Client CCX version............................... 6
CCX Foundation Service version................... 1
CCX Management Service version................... Not Available
CCX Voice Service version........................ Not Available
CCX Location Service version..................... Not Available
My questions are:
1. Is there an extra config on the WLC to enable Radio Measurements?
2. Why is the client reported as having RM disabled?
3. Are there any additional client configurations that must be done?
Thank you.Welcome to Discussions, heather2910
heather2910 wrote:
when i click on a contact and then click on facetime it says that the contact is unavalible how do i get it to work?
(1) Consider the FaceTime troubleshooting suggestions in this article:
http://support.apple.com/kb/HT4319
(2) If your FaceTime works to some of your FaceTime friends but not to others, those who show "unavailable" may merely not have their FaceTime turned on so they can receive calls.
EZ Jim
Mac Pro Quad Core (Early 2009) 2.93Ghz Mac OS X (10.6.7); MacBook Pro (13 inch, Mid 2009) 2.26GHz (10.6.7)
LED Cinema Display; G4 PowerBook 1.67GHz (10.4.11); iBookSE 366MHz (10.3.9); External iSight; iPod4touch4.3.1 -
WLC 5508 - wlan stability problems
Hi.
I have a WLC 5508 with half a dozen LAPs (AIR-CAP3502I-E-K9).
They have been working but sometimes clients detect conectivity problems with the wlan.
Here is the message log I can obtain from the controller:
Nov 09 12:16:31.886: [ERROR] pemTimers.c 330: invalid interface name (john_doe) in mscb!!!*dot1xMsgTask: Nov 09 12:16:10.286: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client 00:26:c6:12:e8:32Previous message occurred 7 times.Nov 09 11:55:24.682: [ERROR] pemTimers.c 330: invalid interface name (john_doe) in mscb!!!*apfReceiveTask: Nov 09 11:51:30.788: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *spamApTask2: Nov 09 11:51:20.144: %DTLS-3-HANDSHAKE_FAILURE: openssl_dtls.c:631 Failed to complete DTLS handshake with peer 10.23.1.118*dot1xMsgTask: Nov 09 11:50:44.878: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client e0:ca:94:93:be:67*apfReceiveTask: Nov 09 11:50:40.672: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:38.625: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:35.531: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:31.068: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:29.257: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:28.707: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg *apfReceiveTask: Nov 09 11:50:24.065: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
Can somebody help me to understand these messages?
1)
*apfReceiveTask: Nov 09 11:50:24.065: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
2)
Nov 09 11:55:24.682: [ERROR] pemTimers.c 330: invalid interface name (john_doe) in mscb!!!
3)
*dot1xMsgTask: Nov 09 11:50:44.878: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client e0:ca:94:93:be:67
Thanks1)
*apfReceiveTask: Nov 09 11:50:24.065: %RRM-3-RRM_LOGMSG: rrmChanUtils.c:290 RRM LOG: Airewave Director: Could not find valid channel lists for 802.11bg
//APs are rebooting. don't panic, check the up time of AP. This message seen when AP rebooted/freshly joined and waiting for wlc to assign channel.
2)
Nov 09 11:55:24.682: [ERROR] pemTimers.c 330: invalid interface name (john_doe) in mscb!!!
//It is cosmetic and can be ignored.
3)
*dot1xMsgTask: Nov 09 12:16:10.286: %DOT1X-3-MAX_EAPOL_KEY_RETRANS: 1x_ptsm.c:444 Max EAPOL-key M1 retransmissions exceeded for client 00:26:c6:12:e8:32
//Keys M1-M5 used for wireless auth, here client having struggle completing the auth process.
get output of, WLC>debug client -
CiscoWorks LMS 3.2 device driver discovery problem
Hi,
We have many devices Cisco 3825 on our network. For some of them, the device driver is correctly discovered but not for others.
- Devices correctly discovered : cisco3825 : Cisco IOS Software, 3800 Software (C3825-ADVSECURITYK9-M), Version 12.4(5a), RELEASE SOFTWARE (fc3)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2006 by Cisco Systems, Inc.Compiled Fri 13-Jan-06 21:09 by alnguyen : snmp oid : .1.3.6.1.4.1.9.1.543
- Devices not recognized : cisco3825 : Cisco IOS Software, 3800 Software (C3825-ADVSECURITYK9-M), Version 12.4(15)T9, RELEASE SOFTWARE (fc5)Technical Support: http://www.cisco.com/techsupportCopyright (c) 1986-2009 by Cisco Systems, Inc.Compiled Tue 28-Apr-09 17:45 by prod_rel_team : snmp oid : .1.3.6.1.4.1.9.1.543
I didn't see any new device driver package on Cisco site.
Does somebody has an idea ?
Many thanks,
Fabien GIRAUDI'm not sure I clearly understand the problem. Are you saying that some 3825s are not being discovered by Common Services Discovery? If so, are they showing up as unreachable, or are they not showing up at all in the Discovery reports?
-
Discovery problem in LMS 4.0.1
Hello all,
I have a problem discovering some ASA firewalls on a network. I have several ASA firewalls on this /24 network, but some of them I can't discover e.g 149.x.x.107 is discovered ok, but 149.x.x.20 I can't discover. It seems that it's not even trying to discover the devices I have problems with. Nothing is shown in the discovery log
I hope someone can help me.
Thanks in advanceIf I ping the firewalls, then I can see all the firewalls in the ARP table, including the firewalls I can't discover.
Below is a part of the ARP table from the seed device
Internet x.x.x..21 172 7081.05d3.91ea ARPA Ethernet0/0 (can't disover)
Internet x.x.x..20 17 7081.05d3.a158 ARPA Ethernet0/0 (can't disover)
Internet x.x.x.13 12 001a.6dea.51cb ARPA Ethernet0/0 (can't discover)
Internet x.x.x.14 12 30e4.db7b.7021 ARPA Ethernet0/0 (can't discover)
Internet x.x.x.19 0 68ef.bdb1.6227 ARPA Ethernet0/0
Internet x.x.x.18 0 5475.d0c3.9827 ARPA Ethernet0/0
Internet x.x.x.7 0 001e.f762.d405 ARPA Ethernet0/0
Internet x.x.x.8 0 001e.f762.d3e1 ARPA Ethernet0/0
Internet x.x.x..33 0 0012.d94f.c1b4 ARPA Ethernet0/0
Internet x.x.x..34 0 0012.0182.d82e ARPA Ethernet0/0
Internet x.x.x.107 0 0015.c695.b879 ARPA Ethernet0/0
Internet x.x.x.108 2 0015.fac8.15b3 ARPA Ethernet0/0 -
Hello all,
I've got a following problem with bringing up simple wireless configuration. There is a WLC-4402 controller and several remote locations (I am testing one so far). Two WLAN configured (one for employee and the other for guest access - no mobility anchoring used, guest is just mapper to VLAN restricted on the firewall). WLC serves DHCP pools for wireless clients. Problem I am experiencing at the moment is that user with laptop is able to connect to guest WLAN, got an IP but can communicate (ping) only its own IP, the controller IP in guest subnet and default gateway (which is the firewall interface). Traffic to any other destinations never hit gateway (I am running tcpdump on it to confirm). I double checked controller config but no luck so far. Could that be caused by missconfigured tunnel? No ACL or restriction set on WLC - see attached config.
Thank you in advance,
PeterIs this an open network or have you enabled layer 3 security? Web Auth? I can see you have created a lobby admin account so expect that you use this for guest account creation with web auth..
When you associate/receieve IP address to the open guest network have you then opened a web browser and authenticated? Until you enter your login details created on the WLC I would imagine that you wouldn't be able to send any data.
If you have authenticated already, can you check on the WLC that the client is associated/authenticated and is the Corp network ok? Also what is the topology between the WLC/Firewall/Remote sites.
Cheers
Mat
Maybe you are looking for
-
Hp 21-ho39 and external monitor
I have an external monitor I would like to hook up to my all-in-one. But it only allows me to hook up a wireless monitor. My computer does not see my external monitor. This question was solved. View Solution.
-
Succession Planning 2.1 integration with portal
In the installation guide for 2.1 Succession Planning, it mentions assigning users to one of the following portal roles after the portal content has been imported: Manager Self-Service - portal_content/com.sap.pct/line_manager/com.sap.pct.erp.mss.bp_
-
Airport spontaneously stopped seeing any networks
Hey guys, long time listener first time caller. My macbook is doing the darndest thing. Randomly last night, my mb started disconnecting from my wireless network. I would re-enter the information, hit connect and it would connect for about 1 minute a
-
Refurbished 13 inch MacBook Pro
Hi, Is there anyway to tell what generation of MacBook Pro your looking at on the Apple Store? thanks Jeff
-
I have the following piece of code within an event which does a lot of reading and writing from and into different files. The process takes about 10 seconds. ProgBar p = new ProgBar(jProgressBar1); void okbutton_actionPerformed(ActionEvent e) tem