Splash Page in WLC 2500 Series
Can someone tell me if there is Splash Page feature in the 2500 WLC ? I cannot find any Cisco document which says it has that feature ?
Yes, Its available.
Here is a link that points to a configuration guide for a wlc 2500, 7.5.
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-5/config_guide/b_cg75.pdf
"The splash page web redirect feature is available only for WLANs that are configured for 802.1X or
WPA+WPA2 Layer 2 security with 802.1x key management."
Similar Messages
-
As far as I can find this model comes with 4 X Gigabit ports but does not support Etherchannel or LAG .. .. can someone confirm this ? I assume this is this a hardware limitation since it uses the 7.0 code as the 5508 series right ?
Correct, the 2500 does not support LAG/Etherchannel.
"An interface is a logical entity on the controller. An interface has multiple parameters associated with it, including IP address, default-gateway (for the IP subnet), primary physical port, secondary physical port, VLAN tag, and DHCP server. Since LAG is not used, each interface is mapped to at least one primary physical port and an optional secondary port. Multiple interfaces can be mapped to a single Wireless Controller port."
From here: http://www.cisco.com/en/US/customer/products/ps11630/products_tech_note09186a0080b8450c.shtml#cliconfig -
Does WLC 2500 series spupports 1262 series Access Point?
Does AIR-CT2504-25-K9 spupports AIR-LAP1262N-E-K9 Access Point? How can I check this?
AFAIK, the 2504 supports anything in the 7.0.116.0 Release Note. It should be called out in the release note if the 2504 does not support anything in particular.
Since the 1262 is the non CleanAir version of the 3502e, which is only availabile in 7.0+ anyhow, I would have to imagine it is supported in the new WLC. -
WLC 2500 Series: differences between 7.0 and 7.2 Firmwares?
Hello everybody.
I'm quite new to Cisco WLAN Controllers, thus I'm asking now (as I have to configure one from ground on): which differences exist between 7.0 and 7.2 firmwares? I have to decide/choose which of them to run, before continuing to configure my WLAN infrastructure.
Thanks in advance and kind regards,
F.If this is a brand new install the answer is simple in my mind, go with 7.2. There are a lot of neat features in 7.2 that are not in 7.0, plus 7.0 is on maintenance releases only now, 7.2 is the new main code for supporting the newer WLCs. Besides TAC generally wants you to upgrade to the latest if you call them for help so you might as well get started on the new code now when you don't have to worry about bringing the networks down to upgrade.
Sent from Cisco Technical Support iPad App -
Hello all,
I have a 3502 ap connected to a 2100 WLC, I want to create and SSID with wpa/wpa2 with psk authentication. Cisco duomentation shows that it is not possible as it fllas back to 802.1x auth.
is there a way to create an ssid with psk and a splash page that shows company service agreement with only a button that shows I accept these terms?
Thank you allHi,
If i understand correctly: you want to have a WLAN with WPA/WPA2 -PSK and webauth page with term and condition and you want that user just click on agree button and get connection.
Yes you can create a SSID with WPA/WPA2-psk.
Check this Wireless LAN Controller Layer 2 – Layer 3 Security Compatibility Matrix
http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/106082-wlc-compatibility-matrix.html
Regards
Dont forget to rate helpful posts -
Guest Splash Page with Cisco WLCs Help
Hi,
I need some guidance using Web Authentication / Web Pass-through to create a mandatory splash page that is presented to users of our guest WLAN. Currently our guest WLAN is wide open, users connect and go straight through to get Internet Access. Here's what we'd like to accomplish.
1. Have the page hosted on an external web server (i.e not on the controller)
2. Present Terms of service
3.
a. Present an optional field to enter an email address & date of birth (DOB) to opt in for marketing purposes
OR
b. Present a mandatory field to enter an email address with an optional check box and DOB to opt in for marketing (the idea behind option b, is that whether they opt in for marketing or not, we could still some how use the email as a username, but not require a password. In the hopes of then using this as a unique identifier in the WLC for troubleshooting / reporting purposes)
4. At the very end, have an "I Agree" button
5. Re-direct to our copmany's public facing website
Our controllers are 5508s, running 7.4.121.0. I more or less have an idea of how to accomplish this, but I've never used Web Auth / Web Passthrough with a Cisco Controller before, so I'm hoping someone can clear up a few things for me.
1. Am I correct that, when using an External server to host the login.html page, we must use Web Authentication, since Web Pass-through is only an option when using an Internal Page? Web Pass-through seems ideal for us, since we don't care about credentials, but from what I'm reading, it seems restricted to Internal (on the Controller) deployments only.
Based on these
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/115951-web-auth-wlc-guide-00.html#passthrough
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/116879-configure-wlc-00.html
http://www.cisco.com/c/en/us/support/docs/wireless/4400-series-wireless-lan-controllers/107474-web-pass-config.html
2. If Web Pass-through is not an option when using an External deployment, is there any way we could use an email address as a username, but not require a password? If not, is hiding the username/password fields in the html code of the splash page, and using a single pre-configured default username / password the only other option ? As described here: https://supportforums.cisco.com/discussion/10847046/unsecured-guest-access-customizable-splash-page-and-logo
3. It sounds like SSL cert warnings may be an issue even if we use an External deployment, because the controller still acts as a middle man. Is this correct, and is the best fix to install a valid 3rd party cert on the controller?
P.S. I’m aware of the Big Brother type things that can be done with Cisco MSE and Connected Mobile Experiences, as far as guest tracking / marketing / analytics go. However, that’s way more than we’re looking to do at this point.
Thanks in advance for any guidance you can provide!Hello Jonathan,
The idea you have is fine, the only exception is the extra fields of information that you want to collect. From the WLC perspective this is not possible to gather.
The example given on https://supportforums.cisco.com/discussion/10847046/unsecured-guest-access-customizable-splash-page-and-logo looks very interesting, and as long as the WLC receive the information it needs to authenticate the client, you can modify the HMTL code as you want. However, as somebody state on that post, Cisco provides the html example, but we do not really support the html content creation or modification.
Anyway below on answer #2 I am giving you an idea that could work (again Im not html expert I don't know if that could be achieved that way) maybe you can have a better idea.
To answer your queries:
1) The customized web-passthrough page can be hosted on an external Web Server.
When the pages are on an external webserver, the passthrough is still performed on the WLC, just the pages reside on the external server. It is a good idea to be sure that the pages come up ok on the external server without webauth involved since webauth will not work unless the external webserver works
2) We have examples of what HTML content a customized Web Passthrough page should include. If you add extra fields on the HTML code (like email address & date of birth), the WLC won't be able to handle this data and most probably you won't be able to gather this information from the WLC , unless you customize the web page in such way that it sends the fields email address & date of birth to another server (rather than to the WLC) to gather this information, but at the end what matter for the WLC is to receive the click on the "Accept" button to authenticate the client.
3) Regarding the certificate, there are two options, the cheapest and easiest is to disable HTTPS for web authentication. Then, your guests will open an HTTP web page, without having the certificate warning.
Whether or not you perform local or external web authentication, you still hit the internal web server on the controller. When you redirect to an external web server, you still receive the certificate warning from the controller unless you have a valid certificate on the controller itself. If the redirect is sent to https, you receive the certificate warning from the controller and from the external web server, unless both have a valid certificate.
In order to get rid of the certificate warnings all together, you need to have a root level certificate issued and downloaded onto your controller. The certificate is issued for a host name and you put that host name in the DNS host name box under the virtual interface on the controller. You also need to add the host name to your local DNS server and point it to the virtual IP address (1.1.1.1) of the WLC.
This link provides information about WebAuthentication on an External Web Server, however exactly the same applies for Web Passthrough:
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71881-ext-web-auth-wlc.html
Also, you can download the WebAuthentication bundle, with the examples and some useful information about different customized web pages, it can be used as a template to build your page. Here you will see that Web Passthrough to an external server is indeed a valid option, when you download and unzip it, open the "readme.html"
https://software.cisco.com/download/release.html?mdfid=282600534&softwareid=282791507&release=1.0.2&relind=AVAILABLE&rellifecycle=&reltype=latest
Hope this helps -
WLC 5508 Web Auth Splash Page: Is it possible to place a download?
Hi,
I know it is possible to create custom web auth splash pages on the WLC 5508. Is it also possible to embedd a small document (less than 1MB) that users can download directly from the controller? I need this for providing the terms of use for the Guest WLAN.
Thanks
MichaelIt could be done, but you will want to stay within the limits of the WebAuth bundle size (~ <10MB I believe). This shouldn't be a problem considering a .doc size, but I have to ask the same question. Why would you want to do this as opposed to just putting your terms of use inline to the page as just text/html? Maybe there is a good reason, but I can't really think of any scenario. Feel free to elaborate.
-
I am administrating a wireless network consisting of 11 APs, ASA 5510, WLC 4402 and Router 1760.
The network is sharing an internet connection to all guests without charge so I have no need for authorisation of guests.
I would like to implement a splash page that would be shown to all clients when they first connect. The splash page is suppoused have only the basic information about the provided service and no logon.
Is there a way to do this without purchasing an ACS?
Thank you for your help.Hello!
Yes, if you don't need for authentication (which would require to define the users locally on the WLC or using an external RADIUS server.. as ACS), you can enable Web Auth Passthrough on the WLC directly.
Check this config example:
http://www.cisco.com/en/US/products/ps6366/products_configuration_example09186a00809bdb5f.shtml
In any case, this thread should better go to the Wireless community if ACS is not involved.
I hope this helps!
Regards,
Federico
If this answers your question please mark the question as "answered" and rate it, so other users can easily find it. -
Is it possible to have 2500 series management interface out of band of APs?
I currently have 2500 series WLCs. Our wireless network is completely separate from our internal network, keeping the WLC from talking to any internal servers. The company would like to start using AD(LDAP authentication) for end users while still keeping the APs on a completely separate network. Since the 2500 series does not support a "service port", Is there any way to move the management port out-of-band with no access to APs and just use the other ports for AP management?
I haven't had my morning coffee ... But let me give this a shot..
I am going to say no. The managment interface is needed for APs to join. If you isloate this interface no APs can join. Even if AP managers are used, the AP requries to touch the managment interface when booting up.
"Satisfaction does not come from knowing the solution, it comes from knowing why." - Rosalind Franklin
"I'm in a serious relationship with my Wi-Fi. You could say we have a connection."
"Im like bacon, I make your wireless better" -
Hi,
I have successfully connected my WLC 2500 controller with 20 light weight Access points 1262N.
I have used the internal DHCP server option in the controller for the AP's and client.
Port 1 of the WLC is trunked with the switch 2960. All is working fine
The problem comes when I remove the Ethernet cable from the management interface and restart the WLC. The AP's don't come back. If I don't restart the WLC the AP's remain.
On the other hand, when I leave the Ethernet cable connected to the management port with my pc and then reboot the WLC, the AP's appear.
Seems like whenever im not physically connected to the management port of the WLC and restart it, the AP's don't come back. The only way to make them come back again is to connect my PC to the management port.
Please help me. What seems to be the problem here ?
Best Regards,Hi,
All 20 Pc;s are in one area connected to the same AP im assuming. The PC;s are stationary, so didnt check for roaming, but generally my laptop connectivity is fine while roaming. It rarely disconnects but users have complained that it did disconncect a few times.
Please see below the WLC configuration:
User:Dawaa
Password:********
(Cisco Controller) >sh
(Cisco Controller) show>running-config
Notice: "show running-config" has been changed to be an alias to "show run-config".
Use "show run-config commands" to display the configuration commands.
Press Enter to continue or to abort...
System Inventory
NAME: "Chassis" , DESCR: "Cisco 2500 Series Wireless LAN Controller"
PID: AIR-CT2504-K9, VID: V01, SN: PSZ163602PD
Burned-in MAC Address............................ 20:3A:07:67:C3:00
Maximum number of APs supported.................. 15
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.3.101.0
Bootloader Version............................... 1.0.16
Field Recovery Image Version..................... 1.0.0
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... tEthernet0
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.0.140
Last Reset....................................... Software reset
System Up Time................................... 0 days 1 hrs 23 mins 40 secs
System Timezone Location......................... (GMT +3:00) Baghdad
Configured Country............................... SA - Saudi Arabia
Operating Environment............................ Commercial (0 to 40 C)
--More or (q)uit current module or to abort
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +26 C
External Temperature............................. +30 C
Fan Status....................................... 4200 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 10
Burned-in MAC Address............................ 20:3A:07:67:C3:00
Maximum number of APs supported.................. 15
Press Enter to continue or to abort
AP Bundle Information
Primary AP Image Size
ap1g2 10596
ap3g1 11088
ap3g2 10968
ap801 7092
ap802 8428
c1130 5072
c1140 9288
c1250 6784
c1520 7852
c602i 3736
Secondary AP Image Size
ap1g2 10596
ap3g1 11088
ap3g2 10968
ap801 7092
ap802 8428
--More or (q)uit current module or to abort
c1130 5072
c1140 9288
c1250 6784
c1520 7852
c602i 3736
Press Enter to continue or to abort
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features:
case-check ...........Enabled
consecutive-check ....Enabled
default-check .......Enabled
username-check ......Enabled
Press Enter to continue or to abort
Network Information
RF-Network Name............................. Dawaa
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Enable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
AP Multicast/Broadcast Mode................. Multicast Address : 239.60.60.60
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
--More or (q)uit current module or to abort
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Enable
Mgmt Via Dynamic Interface.................. Enable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth Redirect Ports .................... 80
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
Press Enter to continue or to abort
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Forw Enable Auto 1000 Full Up Enable N/A
2 Normal Disa Enable Auto Auto Down Enable N/A
3 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
Press Enter to continue or to abort
AP Summary
Number of APs.................................... 14
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP6c20.56a0.b352 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:52 default location 1 SA 1
AP6c20.5666.e34a 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:4a default location 1 SA 1
AP6c20.56a0.b341 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:41 default location 1 SA 1
AP6c20.56a0.b4db_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:db Expiry Warehouse 1 SA 1
AP6c20.569a.59da 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:da default location 1 SA 1
AP6c20.5666.e2db 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:db default location 1 SA 1
AP6c20.568c.d530_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d5:30 default location 1 SA 1
AP6c20.5666.e2ca 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:ca default location 1 SA 1
AP6c20.5666.e354 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:54 default location 1 SA 1
AP6c20.569a.59fd 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:fd default location 1 SA 1
AP6c20.56a0.b346 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:46 default location 1 SA 1
AP6c20.56a0.b2f0 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b2:f0 default location 1 SA 1
AP6c20.568c.d1ec 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d1:ec default location 1 SA 1
AP6c20.56a0.b425 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:25 default location 1 SA 1
--More or (q)uit current module or to abort
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
AP6c20.56a0.b352 disabled -
AP6c20.5666.e34a disabled -
AP6c20.56a0.b341 disabled -
AP6c20.56a0.b4db_(Expiry) disabled -
AP6c20.569a.59da disabled -
AP6c20.5666.e2db disabled -
AP6c20.568c.d530_(Expiry) disabled -
AP6c20.5666.e2ca disabled -
AP6c20.5666.e354 disabled -
AP6c20.569a.59fd disabled -
AP6c20.56a0.b346 disabled -
AP6c20.56a0.b2f0 disabled -
AP6c20.568c.d1ec disabled -
AP6c20.56a0.b425 disabled -
Press Enter to continue or to abort
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description.................................
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band.....................................
5 GHz band.......................................
WLAN ID Interface Network Admission Control Radio Policy
1 management Disabled None
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
AP6c20.56a0.b352 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:52 default location 1 SA 1
AP6c20.5666.e34a 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:4a default location 1 SA 1
AP6c20.56a0.b341 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:41 default location 1 SA 1
AP6c20.56a0.b4db_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:db Expiry Warehouse 1 SA 1
--More or (q)uit current module or to abort
AP6c20.569a.59da 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:da default location 1 SA 1
AP6c20.5666.e2db 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:db default location 1 SA 1
AP6c20.568c.d530_(Expiry) 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d5:30 default location 1 SA 1
AP6c20.5666.e2ca 2 AIR-LAP1262N-E-K9 6c:20:56:66:e2:ca default location 1 SA 1
AP6c20.5666.e354 2 AIR-LAP1262N-E-K9 6c:20:56:66:e3:54 default location 1 SA 1
AP6c20.569a.59fd 2 AIR-LAP1262N-E-K9 6c:20:56:9a:59:fd default location 1 SA 1
AP6c20.56a0.b346 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b3:46 default location 1 SA 1
AP6c20.56a0.b2f0 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b2:f0 default location 1 SA 1
AP6c20.568c.d1ec 2 AIR-LAP1262N-E-K9 6c:20:56:8c:d1:ec default location 1 SA 1
AP6c20.56a0.b425 2 AIR-LAP1262N-E-K9 6c:20:56:a0:b4:25 default location 1 SA 1
Press Enter to continue or to abort
RF Profile
Number of RF Profiles............................ 0
Out Of Box State................................. Disabled
RF Profile Name Band Description Applied
Press Enter to continue or to abort
AP Config
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP6c20.56a0.b352
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:a0:b3:52
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.111
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
--More or (q)uit current module or to abort
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
--More or (q)uit current module or to abort
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z0A6
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 01 m 44 s
AP LWAPP Up Time................................. 0 days, 01 h 25 m 37 s
Join Date and Time............................... Wed Mar 13 16:10:25 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
--More or (q)uit current module or to abort
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:7a:20
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
--More or (q)uit current module or to abort
MCS 11................................... DISABLED
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
--More or (q)uit current module or to abort
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 3
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 6
Extension Channel ......................... NONE
--More or (q)uit current module or to abort
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
--More or (q)uit current module or to abort
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Cisco AP Identifier.............................. 0
Cisco AP Name.................................... AP6c20.56a0.b352
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
--More or (q)uit current module or to abort
MAC Address...................................... 6c:20:56:a0:b3:52
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.111
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
--More or (q)uit current module or to abort
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z0A6
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
--More or (q)uit current module or to abort
AP Up Time....................................... 0 days, 22 h 01 m 44 s
AP LWAPP Up Time................................. 0 days, 01 h 25 m 37 s
Join Date and Time............................... Wed Mar 13 16:10:25 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211n-5
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:7a:20
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
--More or (q)uit current module or to abort
9000 Kilo Bits........................... SUPPORTED
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... DISABLED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
--More or (q)uit current module or to abort
MCS 15................................... SUPPORTED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
--More or (q)uit current module or to abort
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 36
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
--More or (q)uit current module or to abort
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
--More or (q)uit current module or to abort
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Press Enter to continue or to abort
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP6c20.5666.e34a
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:66:e3:4a
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.39
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
--More or (q)uit current module or to abort
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09V
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 03 m 17 s
AP LWAPP Up Time................................. 0 days, 01 h 28 m 23 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 04 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
--More or (q)uit current module or to abort
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 54:78:1a:f2:51:c0
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
MCS 11................................... DISABLED
--More or (q)uit current module or to abort
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 1
Number Of Channels ........................ 13
--More or (q)uit current module or to abort
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
Tx Power
Num Of Supported Power Levels ............. 8
Tx Power Level 1 .......................... 20 dBm
Tx Power Level 2 .......................... 17 dBm
Tx Power Level 3 .......................... 14 dBm
Tx Power Level 4 .......................... 11 dBm
Tx Power Level 5 .......................... 8 dBm
Tx Power Level 6 .......................... 5 dBm
Tx Power Level 7 .......................... 2 dBm
Tx Power Level 8 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 2
Phy DSSS parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 1
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
--More or (q)uit current module or to abort
Allowed Channel List....................... 1,2,3,4,5,6,7,8,9,10,11,12,
......................................... 13
Current CCA Mode .......................... 0
ED Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 12 dB
Coverage exception level................... 25 %
--More or (q)uit current module or to abort
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Cisco AP Identifier.............................. 1
Cisco AP Name.................................... AP6c20.5666.e34a
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:66:e3:4a
--More or (q)uit current module or to abort
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.39
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
--More or (q)uit current module or to abort
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09V
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... AUTOMATIC
AP User Name..................................... Not Configured
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 03 m 17 s
--More or (q)uit current module or to abort
AP LWAPP Up Time................................. 0 days, 01 h 28 m 23 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 04 s
Attributes for Slot 1
Radio Type................................... RADIO_TYPE_80211n-5
Radio Subband................................ RADIO_SUBBAND_ALL
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 54:78:1a:f2:51:c0
Operation Rate Set
6000 Kilo Bits........................... MANDATORY
9000 Kilo Bits........................... SUPPORTED
--More or (q)uit current module or to abort
12000 Kilo Bits.......................... MANDATORY
18000 Kilo Bits.......................... SUPPORTED
24000 Kilo Bits.......................... MANDATORY
36000 Kilo Bits.......................... SUPPORTED
48000 Kilo Bits.......................... SUPPORTED
54000 Kilo Bits.......................... SUPPORTED
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... DISABLED
MCS 3.................................... SUPPORTED
MCS 4.................................... SUPPORTED
MCS 5.................................... SUPPORTED
MCS 6.................................... SUPPORTED
MCS 7.................................... SUPPORTED
MCS 8.................................... SUPPORTED
MCS 9.................................... SUPPORTED
MCS 10................................... SUPPORTED
MCS 11................................... SUPPORTED
MCS 12................................... SUPPORTED
MCS 13................................... SUPPORTED
MCS 14................................... SUPPORTED
MCS 15................................... SUPPORTED
--More or (q)uit current module or to abort
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String ............................ SA
Multi Domain Capability
Configuration ............................. AUTOMATIC
First Chan Num ............................ 36
Number Of Channels ........................ 4
MAC Operation Parameters
Configuration ............................. AUTOMATIC
Fragmentation Threshold ................... 2346
Packet Retry Limit ........................ 64
--More or (q)uit current module or to abort
Tx Power
Num Of Supported Power Levels ............. 7
Tx Power Level 1 .......................... 17 dBm
Tx Power Level 2 .......................... 14 dBm
Tx Power Level 3 .......................... 11 dBm
Tx Power Level 4 .......................... 8 dBm
Tx Power Level 5 .......................... 5 dBm
Tx Power Level 6 .......................... 2 dBm
Tx Power Level 7 .......................... -1 dBm
Tx Power Configuration .................... AUTOMATIC
Current Tx Power Level .................... 1
Phy OFDM parameters
Configuration ............................. AUTOMATIC
Current Channel ........................... 64
Extension Channel ......................... NONE
Channel Width.............................. 20 Mhz
Allowed Channel List....................... 36,40,44,48,52,56,60,64,100,
......................................... 104,108,112,116,132,136,140
TI Threshold .............................. -50
Legacy Tx Beamforming Configuration ....... CUSTOMIZED
Legacy Tx Beamforming ..................... ENABLED
--More or (q)uit current module or to abort
Antenna Type............................... EXTERNAL_ANTENNA
External Antenna Gain (in .5 dBi units).... 0
Diversity.................................. DIVERSITY_ENABLED
802.11n Antennas
A....................................... ENABLED
B....................................... ENABLED
C....................................... ENABLED
Performance Profile Parameters
Configuration ............................. AUTOMATIC
Interference threshold..................... 10 %
Noise threshold............................ -70 dBm
RF utilization threshold................... 80 %
Data-rate threshold........................ 1000000 bps
Client threshold........................... 12 clients
Coverage SNR threshold..................... 16 dB
Coverage exception level................... 25 %
Client minimum exception level............. 3 clients
Rogue Containment Information
Containment Count............................ 0
CleanAir Management Information
CleanAir Capable......................... No
--More or (q)uit current module or to abort
Radio Extended Configurations
Beacon period.............................. 100 milliseconds
Beacon range............................... AUTO
Multicast buffer........................... AUTO
Multicast data-rate........................ AUTO
RX SOP threshold........................... AUTO
CCA threshold.............................. AUTO
Press Enter to continue or to abort
Cisco AP Identifier.............................. 2
Cisco AP Name.................................... AP6c20.56a0.b341
Country code..................................... SA - Saudi Arabia
Regulatory Domain allowed by Country............. 802.11bg:-AE 802.11a:-E
AP Country code.................................. SA - Saudi Arabia
AP Regulatory Domain............................. -E
Switch Port Number .............................. 1
MAC Address...................................... 6c:20:56:a0:b3:41
IP Address Configuration......................... DHCP
IP Address....................................... 192.168.0.120
IP NetMask....................................... 255.255.255.0
Gateway IP Addr.................................. 192.168.0.220
NAT External IP Address.......................... None
CAPWAP Path MTU.................................. 1485
Telnet State..................................... Disabled
Ssh State........................................ Disabled
Cisco AP Location................................ default location
Cisco AP Group Name.............................. default-group
Primary Cisco Switch Name........................
Primary Cisco Switch IP Address.................. Not Configured
Secondary Cisco Switch Name......................
Secondary Cisco Switch IP Address................ Not Configured
--More or (q)uit current module or to abort
Tertiary Cisco Switch Name.......................
Tertiary Cisco Switch IP Address................. Not Configured
Administrative State ............................ ADMIN_ENABLED
Operation State ................................. REGISTERED
Mirroring Mode .................................. Disabled
AP Mode ......................................... Local
Public Safety ................................... Disabled
AP SubMode ...................................... Not Configured
Remote AP Debug ................................. Disabled
Logging trap severity level ..................... informational
Logging syslog facility ......................... kern
S/W Version .................................... 7.3.101.0
Boot Version ................................... 12.4.2.4
Mini IOS Version ................................ 7.3.1.73
Stats Reporting Period .......................... 180
LED State........................................ Enabled
PoE Pre-Standard Switch.......................... Disabled
PoE Power Injector MAC Addr...................... Disabled
Power Type/Mode.................................. Power injector / Normal mode
Number Of Slots.................................. 2
AP Model......................................... AIR-LAP1262N-E-K9
AP Image......................................... C1260-K9W8-M
IOS Version...................................... 15.2(2)JA$
--More or (q)uit current module or to abort
Reset Button..................................... Enabled
AP Serial Number................................. FCZ1642Z09Y
AP Certificate Type.............................. Manufacture Installed
AP User Mode..................................... CUSTOMIZED
AP User Name..................................... dawaa
AP Dot1x User Mode............................... Not Configured
AP Dot1x User Name............................... Not Configured
Cisco AP system logging host..................... 255.255.255.255
AP Up Time....................................... 0 days, 22 h 07 m 08 s
AP LWAPP Up Time................................. 0 days, 01 h 31 m 05 s
Join Date and Time............................... Wed Mar 13 16:10:26 2013
Join Taken Time.................................. 0 days, 00 h 02 m 19 s
Attributes for Slot 0
Radio Type................................... RADIO_TYPE_80211n-2.4
Administrative State ........................ ADMIN_ENABLED
Operation State ............................. UP
Radio Role .................................. ACCESS
CellId ...................................... 0
Station Configuration
Configuration ............................. AUTOMATIC
--More or (q)uit current module or to abort
Number Of WLANs ........................... 1
Medium Occupancy Limit .................... 100
CFP Period ................................ 4
CFP MaxDuration ........................... 60
BSSID ..................................... 1c:e6:c7:04:81:f0
Operation Rate Set
1000 Kilo Bits........................... SUPPORTED
2000 Kilo Bits........................... SUPPORTED
5500 Kilo Bits........................... SUPPORTED
11000 Kilo Bits.......................... MANDATORY
MCS Set
MCS 0.................................... DISABLED
MCS 1.................................... DISABLED
MCS 2.................................... SUPPORTED
MCS 3.................................... DISABLED
MCS 4.................................... DISABLED
MCS 5.................................... DISABLED
MCS 6.................................... DISABLED
MCS 7.................................... DISABLED
MCS 8.................................... DISABLED
MCS 9.................................... DISABLED
MCS 10................................... DISABLED
MCS 11................................... DISABLED
--More or (q)uit current module or to abort
MCS 12................................... DISABLED
MCS 13................................... DISABLED
MCS 14................................... DISABLED
MCS 15................................... DISABLED
MCS 16................................... DISABLED
MCS 17................................... DISABLED
MCS 18................................... DISABLED
MCS 19................................... DISABLED
MCS 20................................... DISABLED
MCS 21................................... DISABLED
MCS 22................................... DISABLED
MCS 23................................... DISABLED
Beacon Period ............................. 100
Fragmentation Threshold ................... 2346
Multi Domain Capability Implemented ....... TRUE
Multi Domain Capability Enabled ........... TRUE
Country String .............. -
2500 series support mobility groups?
Do you know if the new 2500 series controller supports things like mobility groups? Could I use 2 of these and do inter-controller roaming.
Also do you know if this would work with a 2106 controller and a 2505 controller or are they 2 completely independent controllers only knowing about their own APs??Hi smailmilak,
no mobility and roaming is not the same. You need for roaming between controllers a mobility configuration.
If you have only one 2500 WLC and 25 or more or less AP roaming between the AP on the one WLC will work well.
This calls Intra-Controller roaming
If you have 2 or more WLCs you need a proper mobility config for roaming between APs located on differen WLC.
This Calls Inter-Controller roaming.
More informations are here:
http://www.cisco.com/en/US/docs/wireless/controller/7.0/configuration/guide/c70mobil.html -
Identity Services Engine (ISE) support for the WLC 2500
Is the ISE going to support the 2500 series Wireless LAN Controller WLC? If yes in what release and appriximately when is that due to be released?
Your question is disturbing. ISE is (amongst other things) a radius server. WLC 2500 can use radius servers for authentication. So it's supported.
Any device doing radius is supported with ISE ...
Now you are maybe referring to a particular feature in ISE ? -
Cisco 5508 Wireless Controller with Splash Page Disclaimer
How do one configure a splash disclaimer page on a Cisco Wireless Controller 5508 with no authentication?
JimmyThere are many options to you in this scenario, but if you're looking to simply provide a splash page via the WLC without interacting with any other web servers, you can configure Local Web Authentication (LWA) as seen in this configuration example.
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/69340-web-auth-config.html?referring_site=RE&pos=1&page=http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wlan-security/71881-ext-web-auth-wlc.html
If you are not wanting the authentication, you can choose the "passthrough" method which will not require any credentials, only accepting an AUP or whatever you want. -
I've seen it menitoned in a few places that there are sample web auth splash pages located on the WLC that can be uploaded and modified. I've also hear that there are some sample pages on Cisco's website, but I am unable to find them in either location. How do I access these sample pages?
Jason,
The sample web-auth bundle is located in the same location as the download for the controller code.
http://www.cisco.com/cisco/software/type.html?mdfid=282600534&flowid=7012
there is a link there for the Webauth bundle
HTH,
Steve
Please remember to rate helpful posts or to mark the question as answered so that it can be found later. -
Cisco ISE web auth Splash page
Was wondering if the splash page offered by Cisco ISE can be customized, or if it's necessary to redirect to an External server?
Currently using a downloaded web auth pass-through splash page setup for guest access on a 5508 WLC, but have been asked to move this feature off the WLC and onto the ISE and then customize the page with company logo's and a couple graphics.
Is this possible?
Thanks in advance...Yes, but you will definitely need ISE 1.3. When creating the guest portal in ISE you would select the "Hotspot Guest Portal" option. This allows guest users to just agree to an AUP (Acceptable Use Policy) and then get Wi-Fi access.
And yes, you can also perform posture assessment:
http://www.cisco.com/c/en/us/support/docs/security/identity-services-engine-software/118741-configure-ise-00.html#anc9
Thank you for rating helpful posts!
Maybe you are looking for
-
Zen XTRA is completely dead after installing the latest firmware 2.10
Hello,?I have tried to install the latest firmware 2.0.03 to my Zen Xtra 60GB mp3 player. The installation process completed about 70%. As I understand, at that point the?new firmware was finally uploaded after a couple of player reboots. The?firmwar
-
B&W G3 + Radeon 7000 + Mac OS 8.6 = no dice?
Greetings. I recently acquired a "new to me" B&W G3 (rev 2 motherboard). It came equipped with a Radeon 7000 and Mac OS X. I have since acquired a Rage 128, a new hard drive, and installed Mac OS 8.6 on it. I now have a Radeon 7000 lying around and w
-
How to Restore iCal from Time Machine
Dont now why all my events for next month and future are erase. I want to recover the last time machine back up but dont now how. Can some one bring me the step by step indications?
-
Photoshop for MAC OS X 10.5.8, with only 2 GB of memory?
I have an older laptop running MAC OS X 10.5.8, with only 2 GB of memory. Can I get an old version of photoshop that would be compatible?
-
Photoshop CC und Lightroom CC läst sich nicht installieren. Was kann ich tun?
Photoshop CC und Lightroom CC läst sich nicht installieren. Was kann ich tun?