WLC 5508 Connectivity
Guys,
I have a question regarding LAG ports.
From Rajan's post here https://supportforums.cisco.com/document/81681/lag-link-aggregation he mentioned the following:
When you enable LAG, all ports participate in LAG by default. Therefore, you must configure LAG for all of the connected ports in the neighbor switch.
You cannot configure the controller’s ports into separate LAG groups. Only one LAG group is supported per controller. Therefore, you can connect a controller in LAG mode to only one neighbor device.
I have the following questions:
1) I want to have an OOB port in access and a lag port connected to stack switch in such a way that one port will be connected to master switch and the other to the secondary switch.
2) The OOB port will be access and the lag trunk.
3) Considering Service Port to be configured in same vlan as OOB port just incase.
Is this configuration viable?
For the 5508, the Service Port is meant for Out of Bound Management (OoBM).
Similar Messages
-
WLC 5508 intermittent loss of connectivity
Hi.
I have a WLC 5508 connecting directly to a distribution switch (3850) via a layer 2 etherchannel trunk fibre link with LAG enabled on the WLC.
Whenever there is a loss of power to the server room where both devices are hosted & power later gets restored, the distribution switch & WLC lose Layer 2 & 3 connectivity. Connectivity only gets restored when the WLC is power cycled or the fibre cables connecting to its SFP ports are removed & plugged back in. When this is done connectivity is restored between them, APs associate etc. Once there is a loss of power to the room for whatsoever reason again, the loss of connectivity issue re-occurs.
Disabled the etherchannel at some point, using only a single fibre trunk link between them, but the issue persists.
Also check for interface errors, CRCs, etc on both ends but there are none.
Can anyone please advice me on what the issue is & what can be done to permanently resolve this?
Thanks in anticipation.
Ope.Software version is 7.4.100.0
int gig1/0/5
switchport mode trunk
switchport trunk encapsulation dot1q
channel-group 1 mode on
int gig1/0/6
switchport mode trunk
switchport trunk encapsulation dot1q
channel-group 1 mode on
Port setting on the switch is set to auto-negotiate. Port setting on the controller is "auto". The link has been negotiated (& always negotiates) to 1000Mbps full duplex on both ends.
Presently in transit with no way of connecting to the device, but I checked the duplex & speed settings on both devices which was appropriately negotiated. Also checked for interface error counters on the switch, there was none. Checked the WLC logs too, there were no logs on issues with the interfaces or auto-negotiation. -
Hi,
I have a WLC 5508 connected in a hub and spoke topology. The WLC is located at the hub which is the main office. In one of the remote spoke locations I have five Access Points that are connected to the local LAN and the model for the APs is AIR-CAP3602I-E-K9. The APs are all connected to access ports on the switch in vlan 1. I have two WLAN configured on the controller. I have two interfaces configured on the controller. The management and the guest interface. WLAN 1 is associated with the management interface. In the WLAN 1 advanced setting the flex local switching option is enabled. WLAN 2 is associated with the guest interface and this interface is tunneling vlan 248 the guest vlan. The problem I am having is that the devices can not communicate with each other if they are connected to the wireless connection WLAN 2 which is the tunneled vlan.
Example: The client would like to be able to connect his ipad to the apple tv for presentation. If I connect both devices to the WLAN 1 which is using flex local switching option they can communicate with no problem, but if the devices are connected to WLAN 2 the guest vlan they can't communicate with each other. Is it possible to get this to also work on WLAN 2 ?
Note: Both WLAN types are WLAN and P2P Blocking Action is set to default (disabled).
Does any one have any ideas what could be causing my issue?
Thanks in advance for your help,Well since your talking about Apple TV, you need to look at this reference guide for Apple's bonjour. This will explain how to get it to work and the limitation when an AP is in local or FlexConnect mode. The bonjour just doesn't work as people think it should because they can get it to work with a linksys AP.
http://www.cisco.com/en/US/products/hw/wireless/ps4570/products_tech_note09186a0080bb1d7c.shtml
Sent from Cisco Technical Support iPhone App -
WLC 5508 duplex mismatch error
Hi I've got a WLC 5508 connected to a Catalyst 6000 switch. In the switch I've get a CDP duplex mismatch error every 30 min.
%CDP-4-DUPLEXMISMATCH:Full/half duplex mismatch detected on port 3/23
with the show port command I can see this:
Port Name Status Vlan Duplex Speed Type
3/23 WLC connected trunk full 1000 10/100/1000
With the show CDP neigh I see a duplex mismatch
C6K9> (enable) sh cdp neig 3/23 detail
Port (Our Port): 3/23
Holdtime: 142 sec
Capabilities: HOST
Version:
Manufacturer's Name: Cisco Systems Inc. Product Name: Cisco Controller Product Version: 7.0.116.0 RTOS Version: Erro Bootloader Version: 1.0.1 Build Type: DATA + WPS
Platform: AIR-CT5508-K9
Port-ID (Port on Neighbors's Device): GigabitEthernet0/0/1
VTP Management Domain: unknown
Native VLAN: unknown
Duplex: half (Mismatch)
But in the WLC console there is not half duplex
(WLC5508) show>port 1
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE SFPType
1 Normal Forw Enable Auto 1000 Full Up Enable N/A 1000BaseTX
I don't have errors in the port counters
How I can resolve this duplex mismatch?Try upgrading the firmware of the WLC to 7.0.230.0.
-
Wlc 5508: windows 8 can't connect using wpa+wpa2
Dear All,
I need your help.
My customer have Cisco WLC 5508 (cisco wlc 7.0.116.0) .
We create ssid with layer 2 security wpa+wpa2.
Using Windows 8, it's can't connect to the wireless lan.
But if I change, the ssid, with layer 2 security wep.
It can connect / connected.
Please help.
Thanks,
JerriThis is a known issue with Windows 8. You need to upgrade your firmware to 7.0.250.X for wireless clients running Win8.
Another thing, choose one: Either WPA or WPA2. Don't enable one and "hope" the wireless client will make the choice because most of the time, they won't. -
WLC 5508 - Failed to connect from LMS 3.2
Hello.
I am trying to include a WLC 5508 in our LMS 3.2.
I have defined the device and credentials, but the LMS server cannot get access to it.
If I try to check de device credentials from the Device Center I get a "failed to connect", but if I a try a telnet session, also from Device Center, I get a connection.
I checked the credentails are OK.
Thank you.Hi,
You need to download and install the last package : WLC.RME431.v2-1.zip : http://www.cisco.com/cisco/software/cart.html?imageGuId=E3A42793DA29A1B6AC3024C088F9FBC2B324EC8B&i=rs
You must install : MDF 1.37
You must install packages before WLC.RME431.v2-1.zip:
SharedSwimWLC.RME431.v1-2.zip
SharedDcmaWLC.RME431.v1-1.zip
SharedSwimIOS.RME431.v2-5-4.zip
LibSwim.RME431.v2-5-3.zip
LibCommon.RME431.v2-4-2.zip
Elisabeth
WLC.RME431.v2-1.readme:
Supported Devices
=================
Device Type : Cisco 5500 Series Wireless LAN Controllers
Cisco 3750 Switch with Wireless LAN Controller
Devices/Modules Supported :
Cisco 5508 Wireless LAN Controller : 1.3.6.1.4.1.9.1.1069
Cisco 3750 24+2 port 10/100/1000 Switch with integrated Cisco 4402 Wireless Controller: 1.3.6.1.4.1.9.1.747
Features Supported:
Inventory Manager : Yes
Syslog Analyzer : Yes
Config.Mgmt : Yes
Software Mgmt : Yes
Minimum Software : 6.0.188.0
Hardware and Software Requirements
==================================
Hardware and software requirements are the same as those needed for Resource Manager
Essentials 4.3.1 installation.
You must install Resource Manager Essentials 4.3.1 and MDF 1.37 before installing the
device package.
For a detailed list of requirements, as well as instructions for installing Resource
Manager Essentials 4.3.1, go to Cisco.com.
For documentation on Resource Manager Essentials, see:
http://www.cisco.com/en/US/products/sw/cscowork/ps2073/tsd_products_support_series_home.html
Package Dependencies
====================
To install the WLC Package, you must install the
following dependent packages:
SharedSwimWLC.RME431.v1-2.zip
SharedDcmaWLC.RME431.v1-1.zip
SharedSwimIOS.RME431.v2-5-4.zip
LibSwim.RME431.v2-5-3.zip
LibCommon.RME431.v2-4-2.zip -
WLC 5508 disable wlan client still connected
I have one wlc 5508 running on latest IOS 7.116, there is one wlan abc which i have disable status and disable broadcast, but randomly still i can see from wlc dashboard there is one client connected to this wlan abc. The moment i check on the client details, there is no client connected to that wlan and when return to dashboard, no more client connected to that wlan abc. This happened in randomly, it is bug or something else?
I would guess that the client entry also indicates "probing" as status. It means that the client is not connected. It is actually probing, so it"s looking for that SSID that it probably associated to in the past (so it remembers about it)
-
Can anybody tell me how to connect aironet 1400 to wlc 5508 ??
I try to deploy cisco wlc 5508 to wireless network that based on cisco aironet bridge 1400 seirese , but it dose not work !
when i read the data sheet of the wlc 5508 i found that it is not support that type of bridges , is there anyway to connect aironet 1400 to wlc 5505 ?
thanxDuplicate posts. :P
Go here: https://supportforums.cisco.com/discussion/12136581/can-anybody-tell-me-how-connect-aironet-1400-wlc-5508 -
Is there any separate licencse require for centralized WLC 5508 deployment?
agree with Stephan.
No need for addition license. just need to have number of AP license on WLC.
Just for reference:
H-Reap Design and Deployment Guide
http://www.cisco.com/c/en/us/support/docs/wireless/5500-series-wireless-controllers/71250-h-reap-design-deploy.html
H-REAP Modes of Operation Configuration Example
http://www.cisco.com/c/en/us/support/docs/wireless-mobility/wireless-lan-wlan/81680-hreap-modes.html
Regards -
AIR-CAP1602I-E-K9 Not Talking to WLC 5508
hi all,
can't seem to get my APs to talk to WLC 5508.
can someone advise which WLC firmware to use and where can i get/download (link pls).
currently WLC is running 6.0.199.4.
Mar 1 00:00:47.839: %CDP_PD-4-POWER_OK: All radios disabled - NEGOTIATED inlin
e power source
*Mar 1 00:00:53.931: %CAPWAP-3-ERRORLOG: Not sending discovery request AP does
not have an Ip !!
*Mar 1 00:00:55.963: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 172.28.159.15, mask 255.255.255.192, hostname APfc99.47a3.4d22
Translating "CISCO-CAPWAP-CONTROLLER"...domain server (255.255.255.255)
*Mar 1 00:01:06.899: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROL
LER
*Mar 1 00:01:15.899: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_f8
:72:64'running version 6.0.199.4 is rejected. <<<<
APfc99.47a3.4d22>sh ve
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
ROM: Bootstrap program is C1600 boot loader
BOOTLDR: C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFT
WARE (fc1)
APfc99.47a3.4d22 uptime is 11 minutes
System returned to ROM by power-on
System image file is "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"
Last reload reason:
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-CAP1602I-E-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1726W6DQ
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: FC:99:47:A3:4D:22
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17182J4J
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1726W6DQ
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-E-K9
Configuration register is 0xFHi,
Date and time is ok on the WLC,
I configured Accept Self Signed Certificate (SSC) under Security / AP policy, once done the WLC recognized the AP, but output from the console of the AP power cycle the access point is:
IOS Bootloader - Starting system.
FLASH CHIP: Micronix MX25L256_35F
Xmodem file system is available.
flashfs[0]: 5 files, 2 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31936000
flashfs[0]: Bytes used: 6551040
flashfs[0]: Bytes available: 25384960
flashfs[0]: flashfs fsck took 9 seconds.
Reading cookie from SEEPROM
Base Ethernet MAC address: 4c:00:82:9a:47:a3
************* loopback_mode = 0
Loading "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx"...####################
File "flash:/ap1g2-rcvk9w8-mx/ap1g2-rcvk9w8-mx" uncompressed and installed, entr
y point: 0x100000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
Initializing flashfs...
FLASH CHIP: Micronix MX25L256_35F
flashfs[2]: 5 files, 2 directories
flashfs[2]: 0 orphaned files, 0 orphaned directories
flashfs[2]: Total bytes: 31808000
flashfs[2]: Bytes used: 6551040
flashfs[2]: Bytes available: 25256960
flashfs[2]: flashfs fsck took 9 seconds.
flashfs[2]: Initialization complete.
flashfs[3]: 0 files, 1 directories
flashfs[3]: 0 orphaned files, 0 orphaned directories
flashfs[3]: Total bytes: 11999232
flashfs[3]: Bytes used: 1024
flashfs[3]: Bytes available: 11998208
flashfs[3]: flashfs fsck took 1 seconds.
flashfs[3]: Initialization complete....done Initializing flashfs.
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
memory validate-checksum 30
^
% Invalid input detected at '^' marker.
no ip http server
^
% Invalid input detected at '^' marker.
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
login authentication default
^
% Invalid input detected at '^' marker.
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Warning: the compile-time code checksum does not appear to be present.
cisco AIR-CAP1602I-N-K9 (PowerPC) processor (revision B0) with 98294K/32768K
bytes of memory.
Processor board ID FGL1730S57A
PowerPC CPU at 533Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.1.37
1 Gigabit Ethernet interface
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 4C:00:82:9A:47:A3
Part Number : 73-14671-04
PCA Assembly Number : 000-00000-00
PCA Revision Number :
PCB Serial Number : FOC17284HL9
Top Assembly Part Number : 800-38552-01
Top Assembly Serial Number : FGL1730S57A
Top Revision Number : A0
Product/Model Number : AIR-CAP1602I-N-K9
% Please define a domain-name first.
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
Press RETURN to get started!
*Mar 1 00:00:12.451: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:13.683: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state
to up
*Mar 1 00:00:14.687: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEth
ernet0, changed state to up
*Mar 1 00:00:15.123: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1600 Software (AP1G2-RCVK9W8-M), Version 15.2(2)JB, RELEASE
SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:52 by prod_rel_team
*Mar 1 00:00:15.151: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Mar 1 00:00:15.151: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Mar 1 00:00:16.195: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, chan
ged state to uplwapp_crypto_init: MIC Present and Parsed Successfully
no bridge-group 1 source-learning
^
% Invalid input detected at '^' marker.
%Default route without gateway, if not a point-to-point interface, may impact pe
rformance
*Mar 1 00:00:48.695: %CDP_PD-4-POWER_OK: All radios disabled - INJECTOR_CONFIGU
RED_ON_SOURCE inline power source
*Mar 1 00:00:48.923: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP addre
ss 10.2.3.100, mask 255.255.255.0, hostname AP4c00.829a.47a3
Translating "CISCO-CAPWAP-CONTROLLER.campeche.ecosur.mx"...domain server (10.2.3
.10) [OK]
*Mar 1 00:00:59.915: %CAPWAP-3-ERRORLOG: Did not get log server settings from D
HCP.
*Mar 1 00:00:59.919: %CAPWAP-3-ERRORLOG: Dropping dtls packet since session is
not established. A0203E6, 147E, A020364, A47B, 0
*Mar 1 00:01:09.915: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:33:18.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:33:18.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:33:23.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
logging facility kern
^
% Invalid input detected at '^' marker.
logging trap emergencies
^
% Invalid input detected at '^' marker.
*Jan 29 09:34:17.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.
2.3.230:5246
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Jan 29 09:34:17.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. In
itialising Cfg
*Jan 29 09:34:17.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flas
h. Resetting to default config
*Jan 29 09:34:28.015: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan 29 09:34:28.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 10.2.3.230 peer_port: 5246
*Jan 29 09:34:28.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
*Jan 29 09:34:33.535: %CAPWAP-5-SENDJOIN: sending Join Request to 10.2.3.230
and debug command output enable CAPWAP events
(Cisco Controller) >debug capwap events enable
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.092: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:08.093: 4c:00:82:9a:47:a0 DTLS keys for Control Plane deleted successfully for AP 10.2.3.100
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 DTLS connection closed event receivedserver (10.2.3.230/5246) client (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 Entry exists for AP (10.2.3.100/42107)
*spamApTask7: Jan 29 03:39:08.100: 4c:00:82:9a:47:a0 No AP entry exist in temporary database for 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.104: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.104: apModel:
*spamApTask7: Jan 29 03:39:08.104: apType = 38 apModel:
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Received LWAPP DISCOVERY REQUEST to 6c:41:6a:5f:95:2f on port '13'
*spamApTask0: Jan 29 03:39:08.105: 4c:00:82:9a:47:a3 Discarding discovery request in LWAPP from AP supporting CAPWAP
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Discovery Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:08.105: 4c:00:82:9a:47:a0 Join Priority Processing status = 0, Incoming Ap's Priority 1, MaxLrads = 500, joined Aps =0
*spamApTask7: Jan 29 03:39:08.105: apModel:
*spamApTask7: Jan 29 03:39:08.105: apType = 38 apModel:
*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100 port 42107
(Cisco Controller) >*spamApTask7: Jan 29 03:39:08.106: 4c:00:82:9a:47:a0 Discovery Response sent to 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:18.104: 4c:00:82:9a:47:a3 DTLS connection not found, creating new connection for 10:2:3:100 (42107) 10:2:3:230 (5246)
*spamApTask7: Jan 29 03:39:18.638: acDtlsPlumbControlPlaneKeys: lrad:10.2.3.100(42107) mwar:10.2.3.230(5246)
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Allocated index from main list, Index: 397
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Using CipherSuite AES128-SHA
*spamApTask7: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS keys for Control Plane are plumbed successfully for AP 10.2.3.100. Index 398
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 DTLS Session established server (10.2.3.230:5246), client (10.2.3.100:42107)
*spamApTask6: Jan 29 03:39:18.638: 4c:00:82:9a:47:a3 Starting wait join timer for AP: 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a0 Join Request from 10.2.3.100:42107
*spamApTask7: Jan 29 03:39:23.636: 4c:00:82:9a:47:a3 Deleting AP entry 10.2.3.100:42107 from temporary database.
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 MIC AP is not allowed to join by config
*spamApTask7: Jan 29 03:39:23.637: 4c:00:82:9a:47:a0 Join Request failed! -
Converged Access Design Help (Catalyst 3850 and WLC 5508...Mobility Oracle)
Hello,
I am an engineer working with a Cisco Gold Partner in Saudi Arabia. We have a large university as our client where they are constructing a new
building and require our services to build the network infrastructure. Therefore, we are to implement the routing and switching infrastructure as
well as the Wireless solution.
At present, I have no issues in implementing the R&S infrastructure as it is very straight forward but it has implications on the deployment of
the wireless solution which I explain further below. The R&S infrastructure comprises of the typical Core, Distribution, and Access layers and we
are focusing on the local distribution and access switches with regards to the new building. The client has a converged Layer 3 network spanning
from distribution layer to core layer and they are running EIGRP for this convergence. This is not a problem and has already been implemented.
Yet, the challenge arises in deploying the WLAN infrastructure. The client already has a Cisco WLAN infrastructure in place where they have a
large number of LAPs that are registered with their controllers in the Data Center. They have two WLC 5508 where one is the Primary and the other
the Secondary. The local distribution switch to which the WLC are connected also is the gateway for the SVIs for the SSIDs that are configured on
the controllers. This means that once the packets from the AP come in to the WLC, they are tagged with the correct VLAN and sent to the directly
connected distribution switch which then routes it into the rest of the Layer 3 network. Interestingly, the WLC 5508 are running AireOS 7.6 and
support the "New Mobility" feature. The two controllers have formed a Mobility Group (MG) between each other.
Now, the new building will have two Catalyst 3850 switches installed where each one has a total of 40 AP licenses pre-installed and activated
i.e. a total of 80 APs can be supported by the two switches. A total of 67 LAPs will be deployed in the new building which can be accommodated
between the two switches and their integrated controller.
Yet, based on my understanding and research about Converged Access is that, ideally, the Catalyst 3850 will only run the Mobility Agent (MA)
feature while a central controller would provide the Mobility Controller (MC) service. unfortunately, there are not enough licenses on the
existing WLC 5508 nor can we migrate the new licenses that will facilitate such a split deployment.
This means that I would need to configure the two Catalyst 3850 as independent MC and form a MG between them. I have done this and tested this
already and the mobility is working fine. But my concern is not about getting the Catalyst 3850 to work as this is simple but rather it is
focused on creating a common Mobility Domain (MD) so that clients can roam from this new building to the rest of the campus while maintaining the
state of their connections to the WLAN infrastructure.
To make things more complicated, since the new building will have its own Layer 3 distribution switch and the Catalyst 3850 switches will connect
to this distribution switch, it means that new VLANs and SVIs need to be created for the SSIDs broadcast in the new building. This means that new
subnets need to be assigned to the SSIDs.
As such, I have the following questions:
Q1) If we create new SVIs for the SSIDs (same SSIDs names will be used in the new building as in the rest of the university campus) this means
that new subnets will be assigned to these SSIDs. Now, I believe I have two options...one is to make the new Catalyst 3850s to be in the same MG
as the existing WLC 5508 which then cater for Layer 3 client roaming or I have to treat this as a totally seperate WLAN network and follow on to
the solution as per the next question. Please advise which is a better option?
Q2) I could create separate MG i.e. the new building Catalyst 3850s can be in one MG and the existing controllers can be in another MG. I can
then have one of the existing WLC 5508 (the primary one) to run the Mobility Oracle (MO) feature so as to create a single Mobility Domain (MD).
Would this facilitate in Layer 3 client roaming and RRM for all the controllers in the same MD?
Q3) If I do create a MD, how is this accomplished in such an environment since the documentation is severely limited in this regard?
Please advise at your earliest. To assist further, I have attached a topology diagram which may aid in explaining the situation with more
clarity. If these things are clarified, I will be better able to wrap my head around the technology and in turn service my clients better.
Regards,
AmirHi Amir,
Q1) If we create new SVIs for the SSIDs (same SSIDs names will be used in the new building as in the rest of the university campus) this means that new subnets will be assigned to these SSIDs. Now, I believe I have two options...one is to make the new Catalyst 3850s to be in the same MG as the existing WLC 5508 which then cater for Layer 3 client roaming or I have to treat this as a totally seperate WLAN network and follow on to the solution as per the next question. Please advise which is a better option?
I would configure them in the same mobility group. Also configure same SPG for those two 3850 stacks if users are frequently roaming within these two buildings.
Q2) I could create separate MG i.e. the new building Catalyst 3850s can be in one MG and the existing controllers can be in another MG. I can then have one of the existing WLC 5508 (the primary one) to run the Mobility Oracle (MO) feature so as to create a single Mobility Domain (MD). Would this facilitate in Layer 3 client roaming and RRM for all the controllers in the same MD?
MO is not required (it is only for very large scale deployments)
Q3) If I do create a MD, how is this accomplished in such an environment since the documentation is severely limited in this regard?
Yes, documents are hard to find :(
These notes may be useful to you based on my experience. I am running IOS-XE 3.6.1 in my production.
http://mrncciew.com/2014/05/06/configuring-new-mobility/
http://mrncciew.com/2013/12/14/3850ma-with-5760mc/
HTH
Rasika
*** Pls rate all useful responses **** -
Cisco ISE 1.2 & Cisco WLC 5508 v7.6
Hi all,
we are planning to upgrade our WLC to 7.6 to fix a bug with FlexConnect Client ACLs but I have just seen on the Cisco ISE Compatibility table that the it only recommends up to v7.5 of the WLC 5508...
Cisco have told me to steer clear of 7.5 as it is in a defferred status, so does anyone know, or have running in a lab or production, ISE1.2 with a 5508 WLC v7.6 NAD ?
I would much rather know of any issues people are experiencing before hand than to have to go through a software upgrade and then rollback.
Thanks all
Mario De RosaHi Neno,
right I have this almost working now.
I have simplified the setup. I am not going to do any client provisioning at the moment.
So I can connect to the corporate SSID using EAP-TLS and I can successfully push the branch data VLAN upon successful authorisation.
Now I am trying to introduce the posture element & per user ACLs.
I have defined the redirect ACL & Flex ACL on the vWLC however the NAC agent will not pop-up. The client is in the right VLAN and the redirect ACL seems to be getting applied as the client does get an IP through DHCP. However, the client cannot ping the ISE or access the guest portal when I open the browser.
DNS resolution seems to be working fine.
VLAN220 is my datacentre VLAN which the Management Interface on the controller is plugged in to.
VLAN10 is the branch DATA VLAN.
below is some output to give you some more details...
(Cisco Controller) >show client detail 00:24:d6:97:b3:be
Client MAC Address............................... 00:24:d6:97:b3:be
Client Username ................................. [email protected]
AP MAC Address................................... 18:33:9d:f0:21:80
AP Name.......................................... test-flex-ap
AP radio slot Id................................. 0
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 2
Hotspot (802.11u)................................ Not Supported
BSSID............................................ 18:33:9d:f0:21:81
Connected For ................................... 128 secs
Channel.......................................... 6
IP Address....................................... 10.130.130.120
Gateway Address.................................. 10.130.130.1
Netmask.......................................... 255.255.255.0
IPv6 Address..................................... fe80::f524:1910:69f0:9482
Association Id................................... 1
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Client CCX version............................... 4
Client E2E version............................... 1
--More-- or (q)uit
Re-Authentication Timeout........................ 1651
QoS Level........................................ Silver
Avg data Rate.................................... 0
Burst data Rate.................................. 0
Avg Real time data Rate.......................... 0
Burst Real Time data Rate........................ 0
802.1P Priority Tag.............................. disabled
CTS Security Group Tag........................... Not Applicable
KTS CAC Capability............................... No
WMM Support...................................... Enabled
APSD ACs....................................... BK BE VI VO
Power Save....................................... OFF
Current Rate..................................... m13
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ No
Policy Manager State............................. POSTURE_REQD
Policy Manager Rule Created...................... Yes
AAA Override ACL Name............................ POSTURE_REDIRECT_ACL
AAA Override ACL Applied Status.................. Yes
--More-- or (q)uit
AAA Override Flex ACL Name....................... POSTURE_REDIRECT_ACL
AAA Override Flex ACL Applied Status............. Yes
AAA URL redirect................................. https://pdc-ise-man01.kier.group:8443/guestportal/gateway?sessionId=c8dc800a00000005b3e7e953&action=cpp
Audit Session ID................................. c8dc800a00000005b3e7e953
AAA Role Type.................................... none
Local Policy Applied............................. none
IPv4 ACL Name.................................... none
FlexConnect ACL Applied Status................... Yes
IPv4 ACL Applied Status.......................... Unavailable
IPv6 ACL Name.................................... none
IPv6 ACL Applied Status.......................... Unavailable
Layer2 ACL Name.................................. none
Layer2 ACL Applied Status........................ Unavailable
mDNS Status...................................... Disabled
mDNS Profile Name................................ none
No. of mDNS Services Advertised.................. 0
Policy Type...................................... WPA2
Authentication Key Management.................... 802.1x
Encryption Cipher................................ CCMP (AES)
Protected Management Frame ...................... No
Management Frame Protection...................... No
EAP Type......................................... EAP-TLS
FlexConnect Data Switching....................... Local
--More-- or (q)uit
FlexConnect Dhcp Status.......................... Local
FlexConnect Vlan Based Central Switching......... No
FlexConnect Authentication....................... Central
Quarantine VLAN.................................. 0
Access VLAN...................................... 220
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 10
Fast BSS Transition........................ Not implemented
Client Wifi Direct Capabilities:
WFD capable................................ No
Manged WFD capable......................... No
Cross Connection Capable................... No
Support Concurrent Operation............... No
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 33698
Number of Bytes Sent....................... 19397
Total Number of Bytes Sent................. 19397
--More-- or (q)uit
Total Number of Bytes Recv................. 33698
Number of Bytes Sent (last 90s)............ 19397
Number of Bytes Recv (last 90s)............ 33698
Number of Packets Received................. 283
Number of Packets Sent..................... 147
Number of Interim-Update Sent.............. 0
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Id Request Msg Failures...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Request Msg Failures......... 0
Number of EAP Key Msg Timeouts............. 0
Number of EAP Key Msg Failures............. 0
Number of Data Retries..................... 53
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 2
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
Number of Mic Missing Packets.............. 0
Number of RA Packets Dropped............... 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -42 dBm
Signal to Noise Ratio...................... 41 dB
Client Rate Limiting Statistics:
--More-- or (q)uit
Number of Data Packets Recieved............ 0
Number of Data Rx Packets Dropped.......... 0
Number of Data Bytes Recieved.............. 0
Number of Data Rx Bytes Dropped............ 0
Number of Realtime Packets Recieved........ 0
Number of Realtime Rx Packets Dropped...... 0
Number of Realtime Bytes Recieved.......... 0
Number of Realtime Rx Bytes Dropped........ 0
Number of Data Packets Sent................ 0
Number of Data Tx Packets Dropped.......... 0
Number of Data Bytes Sent.................. 0
Number of Data Tx Bytes Dropped............ 0
Number of Realtime Packets Sent............ 0
Number of Realtime Tx Packets Dropped...... 0
Number of Realtime Bytes Sent.............. 0
Number of Realtime Tx Bytes Dropped........ 0
Nearby AP Statistics:
test-flex-ap(slot 0)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -37 dBm
test-flex-ap(slot 1)
antenna0: 14 secs ago.................... -51 dBm
antenna1: 14 secs ago.................... -54 dBm
--More-- or (q)uit
DNS Server details:
DNS server IP ............................. 10.0.17.31
DNS server IP ............................. 10.0.17.43
Assisted Roaming Prediction List details:
Client Dhcp Required: False
Allowed (URL)IP Addresses
(Cisco Controller) >
(Cisco Controller) >show wlan 2
WLAN Identifier.................................. 2
Profile Name..................................... Demo1x
Network Name (SSID).............................. Demo1x
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Enabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Enabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
--More-- or (q)uit
Number of Active Clients......................... 1
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... mario-test-flex-vwlc
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Disabled
mDNS Profile Name................................ unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
--More-- or (q)uit
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
--More-- or (q)uit
Radius Servers
Authentication................................ 10.0.16.111 1812
Accounting.................................... 10.131.16.111 1813
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
--More-- or (q)uit
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Enabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
--More-- or (q)uit
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexConnect Local Authentication.............. Disabled
FlexConnect Learn IP Address.................. Enabled
Client MFP.................................... Optional
PMF........................................... Disabled
PMF Association Comeback Time................. 1
PMF SA Query RetryTimeout..................... 200
Tkip MIC Countermeasure Hold-down Timer....... 60
Eap-params.................................... Disabled
AVC Visibilty.................................... Disabled
AVC Profile Name................................. None
Flow Monitor Name................................ None
Split Tunnel (Printers).......................... Disabled
Call Snooping.................................... Disabled
Roamed Call Re-Anchor Policy..................... Disabled
SIP CAC Fail Send-486-Busy Policy................ Disabled
SIP CAC Fail Send Dis-Association Policy......... Disabled
KTS based CAC Policy............................. Disabled
Assisted Roaming Prediction Optimization......... Disabled
802.11k Neighbor List............................ Disabled
802.11k Neighbor List Dual Band.................. Disabled
Band Select...................................... Disabled
--More-- or (q)uit
Load Balancing................................... Disabled
Multicast Buffer................................. Disabled
Mobility Anchor List
WLAN ID IP Address Status
802.11u........................................ Disabled
MSAP Services.................................. Disabled
Local Policy
Priority Policy Name
(Cisco Controller) >
when debugging the client during redirect, this is the output and I cannot spot anything wrong here...
(Cisco Controller) >*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Adding mobile on LWAPP AP 18:33:9d:f0:21:80(1)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Association received from mobile on BSSID 18:33:9d:f0:21:8e
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Global 200 Clients are allowed to AP radio
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Max Client Trap Threshold: 0 cur: 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Rf profile 600 Clients are allowed to AP wlan
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 0 Quarantine Vlan 0 Access Vlan 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Re-applying interface policy for client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 255 on mobile
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be In processSsidIE:4850 setting Central switched to FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying site-specific Local Bridging override for station 00:24:d6:97:b3:be - vapId 2, site 'default-group', interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Applying Local Bridging Interface Policy for station 00:24:d6:97:b3:be - vlan 220, interface id 0, interface 'management'
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE statusCode is 0 and status is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be processSsidIE ssid_done_flag is 0 finish_flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be STA - rates (8): 140 18 152 36 176 72 96 108 0 0 0 0 0 0 0 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be suppRates statusCode is 0 and gotSuppRatesElement is 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Processing RSN IE type 48, length 22 for mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Received RSN IE with 0 PMKIDs from mobile 00:24:d6:97:b3:be
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Updating AID for REAP AP Client 18:33:9d:f0:21:80 - AID ===> 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Initializing policy
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Central switch is FALSE
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfMsAssoStateInc
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Idle to Associated
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfPemAddUser2:session timeout forstation 00:24:d6:97:b3:be - Session Tout 0, apfMsTimeOut '0' and sessionTimerRunning flag is 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Stopping deletion of Mobile Station: (callerId: 48)
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Func: apfPemAddUser2, Ms Timeout = 0, Session Timeout = 0
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be Sending Assoc Response to station on BSSID 18:33:9d:f0:21:8e (status 0) ApVapId 2 Slot 1
*apfMsConnTask_7: Aug 12 10:58:24.013: 00:24:d6:97:b3:be apfProcessAssocReq (apf_80211.c:8294) Changing state for mobile 00:24:d6:97:b3:be on AP 18:33:9d:f0:21:80 from Associated to Associated
*spamApTask6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sent 1x initiate message to multi thread task for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be EAP-PARAM Debug - eap-params for Wlan-Id :2 is disabled - applying Global eap timers and retries
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Connecting state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be Sending EAP-Request/Identity to mobile 00:24:d6:97:b3:be (EAP Id 1)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.016: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Received Identity Response (count=1) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Resetting reauth count 1 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be EAP State update from Connecting to Authenticating for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticating state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.083: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=214) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be WARNING: updated EAP-Identifier 1 ===> 214 for STA 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 214)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be Allocating EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.086: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 214, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.090: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=215) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 215)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.091: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 215, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.095: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=216) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 216)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.096: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 216, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.100: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=217) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 217)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.101: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 217, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.105: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=218) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 218)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.106: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 218, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.110: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=219) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.111: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 219, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.115: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=220) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 220)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.116: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 220, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.352: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=221) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 221)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.354: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 221, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.359: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=222) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 222)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.360: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 222, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.365: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=223) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 223)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.366: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 223, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.371: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=224) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 224)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.372: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 224, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.375: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Processing Access-Challenge for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Entering Backend Auth Req state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Sending EAP Request from AAA to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.389: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAPOL EAPPKT from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Received EAP Response from mobile 00:24:d6:97:b3:be (EAP Id 225, EAP Type 13)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Resetting reauth count 0 to 0 for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.391: 00:24:d6:97:b3:be Entering Backend Auth Response state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Processing Access-Accept for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 acl from 255 to 255
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting web IPv4 Flex acl from 65535 to 65535
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Username entry ([email protected]) created in mscb for mobile, length = 253
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be override for default ap group, marking intgrp NULL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 220
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Re-applying interface policy for client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2219)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2240)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Retaining the ACL recieved in AAA attributes 1 on mobile
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Inserting AAA Override struct for mobile
MAC: 00:24:d6:97:b3:be, source 4
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting re-auth timeout to 1800 seconds, got from WLAN config.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Station 00:24:d6:97:b3:be setting dot1x reauth timeout = 1800
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Creating a PKC PMKID Cache entry for station 00:24:d6:97:b3:be (RSN 2)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Resetting MSCB PMK Cache Entry 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Setting active key cache index 8 ---> 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Adding BSSID 18:33:9d:f0:21:8e to PMKID cache at index 0 for station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: New PMKID: (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Disabling re-auth since PMK lifetime can take care of same.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be unsetting PmkIdValidatedByAp
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Client in Posture Reqd state. PMK cache not updated.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAP-Success to mobile 00:24:d6:97:b3:be (EAP Id 225)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Freeing AAACB from Dot1xCB as AAA auth is done for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Found an cache entry for BSSID 18:33:9d:f0:21:8e in PMKID cache at index 0 of station 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: Including PMKID in M1 (16)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: [0000] 6f d1 ce 84 08 74 41 a5 06 6b 89 02 c9 e9 f8 c8
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Starting key exchange to mobile 00:24:d6:97:b3:be, data packets will be dropped
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Entering Backend Auth Success state (id=225) for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be Received Auth Success while in Authenticating state for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.410: 00:24:d6:97:b3:be dot1x - moving mobile 00:24:d6:97:b3:be into Authenticated state
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Received EAPOL-key in PTK_START state (message 2) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be PMK: Sending cache add
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be EAPOL Header:
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00000000: 02 03 5f 00 .._.
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Sending EAPOL-Key Message to mobile 00:24:d6:97:b3:be
state PTKINITNEGOTIATING (message 3), replay counter 00.00.00.00.00.00.00.01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be Reusing allocated memory for EAP Pkt for retransmission to mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappLradNhMac = 00:00:0c:07:ac:dc mscb->apfMsLradSlotId = 1 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsBssid = 18:33:9d:f0:21:80 mscb->apfMsAddress = 00:24:d6:97:b3:be mscb->apfMsApVapId = 2
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 220 mscb->apfMsLwappMwarInet.ipv4.addr = 176217288
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.414: 00:24:d6:97:b3:be mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = 176325157 mscb->apfMsLwappLradPort = 9385
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-Key from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Received EAPOL-key in PTKINITNEGOTIATING state (message 4) from mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Stopping retransmission timer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Freeing EAP Retransmit Bufer for mobile 00:24:d6:97:b3:be
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be apfMs1xStateInc
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 8021X_REQD (3) Change state to L2AUTHCOMPLETE (4) last state 8021X_REQD (3)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central switch is FALSE
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Sending the Central Auth Info
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Central Auth Info Allocated PMKLen = 32
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be PMK: pmkActiveIndex = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be EapolReplayCounter: 00 00 00 00 00 00 00 01
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 apfMsEapType = 13
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) DHCP required on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2for this client
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be Not Using WMM Compliance code qosCap 00
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP 18:33:9d:f0:21:80 vapId 2 apVapId 2 flex-acl-name:POSTURE_REDIRECT_ACL
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state L2AUTHCOMPLETE (4)
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 6166, Adding TMP rule
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255, IPv
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*Dot1x_NW_MsgTask_6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 5761, Adding TMP rule
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Replacing Fast Path rule
type = Airespace AP - Learn IP address
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 ACL ID = 255,
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*apfReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (IPv4 ACL ID 255, IPv6 ACL ID 255, L2 ACL ID 255)
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*pemReceiveTask: Aug 12 10:58:24.418: 00:24:d6:97:b3:be 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*spamApTask6: Aug 12 10:58:24.418: 00:24:d6:97:b3:be spamEncodeCentralAuthInoMsPayload: msAssocTypeFlagsMsb = 0 msAssocTypeFlagsLsb = 2
apfMsEntryType = 0 pmkLen = 32
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 325,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:24.546: 00:24:d6:97:b3:be DHCP setting server from ACK (server 10.0.17.85, yiaddr 10.130.130.120)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 DHCP_REQD (7) Change state to WEBAUTH_REQD (8) last state DHCP_REQD (7)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) pemAdvanceState2 6671, Adding TMP rule
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Replacing Fast Path rule
type = Airespace AP Client - ACL passthru
on AP 18:33:9d:f0:21:80, slot 1, interface = 1, QOS = 0
IPv4 A
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Fast Path rule (contd...) 802.1P = 0, DSCP = 0, TokenID = 64206 Local Bridging Vlan = 220, Local Bridging intf id = 0
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 WEBAUTH_REQD (8) Successfully plumbed mobile rule (IPv4 ACL ID 1, IPv6 ACL ID 255, L2 ACL ID 255)
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Plumbing web-auth redirect rule due to user logout
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be Assigning Address 10.130.130.120 to mobile
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*DHCP Socket Task: Aug 12 10:58:24.548: 00:24:d6:97:b3:be DHCP success event for client. Clearing dhcp failure count for interface management.
*pemReceiveTask: Aug 12 10:58:24.548: 00:24:d6:97:b3:be 10.130.130.120 Added NPU entry of type 2, dtlFlags 0x0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Pushing IPv6 Vlan Intf ID 0: fe80:0000:0000:0000:f524:1910:69f0:9482 , and MAC: 00:24:D6:97:B3:BE , Binding to Data Plane. SUCCESS !! dhcpv6bitmap 0
*IPv6_Msg_Task: Aug 12 10:58:25.330: 00:24:d6:97:b3:be Link Local address fe80::f524:1910:69f0:9482 updated to mscb. Not Advancing pem state.Current state: mscb in apfMsMmInitial mobility state and client state APF_MS_STATE_A
*DHCP Socket Task: Aug 12 10:58:28.581: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 10:58:28.589: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.959: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:00:07.967: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
*DHCP Socket Task: Aug 12 11:01:59.153: 00:24:d6:97:b3:be DHCP received op BOOTREPLY (2) (len 308,vlan 220, port 1, encap 0xec03)
Can you see any obvious reason why the NAC agent wont pop up?
Thanks
Mario -
WLC 5508, SW 6.0.199.4, 1142 AP: Clients getting dropped intermittently
We have deployed a WLC 5508 w/ SW version 6.0.199.4, 1142 AP's & open authentication w/ MAC filtering. Clients are randomly getting dropped with "Limited Access" shown in Win 7. In this state, the client machine is unable to ping the gateway and sometimes lose their DHCP assigned IP as well. A manual disconnect/re-connect to the SSID is required everytime.
I ran a debug on one the clients stuck in the "Limited Access" state (debug client xx:xx:xx:xx):
*Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Adding mobile on LWAPP AP 3c:ce:73:c5:1e:b0(0)
*Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 23) in 5 seconds
*Apr 15 16:59:23.205: e0:91:53:60:1f:e4 apfProcessProbeReq (apf_80211.c:4722) Changing state for mobile e0:91:53:60:1f:e4 on AP 3c:ce:73:c5:1e:b0 from Idle to Probe
*Apr 15 16:59:23.205: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.225: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.225: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.646: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.646: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.666: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:23.666: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 24) in 5 seconds
*Apr 15 16:59:28.553: e0:91:53:60:1f:e4 apfMsExpireCallback (apf_ms.c:418) Expiring Mobile!
*Apr 15 16:59:28.554: e0:91:53:60:1f:e4 0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [3c:ce:73:c5:1e:b0]
*Apr 15 16:59:28.554: e0:91:53:60:1f:e4 Deleting mobile on AP 3c:ce:73:c5:1e:b0(0)
On doing a manual re-connect, got the following logs:
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Association received from mobile on AP b8:62:1f:e9:9f:30
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying site-specific IPv6 override for station e0:91:53:60:1f:e4 - vapId 7, site 'Academy', interface 'students'
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying IPv6 Interface Policy for station e0:91:53:60:1f:e4 - vlan 15, interface id 14, interface 'students'
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 Applying site-specific override for station e0:91:53:60:1f:e4 - vapId 7, site 'Academy', interface 'students'
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 0.0.0.0 START (0) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1276)
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 STA - rates (8): 130 132 139 150 12 18 24 36 0 0 0 0 0 0 0 0
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 STA - rates (12): 130 132 139 150 12 18 24 36 48 72 96 108 0 0 0 0
*Apr 15 17:01:38.143: e0:91:53:60:1f:e4 0.0.0.0 START (0) Deleted mobile LWAPP rule on AP [b8:62:1f:e5:6a:90]
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 Updated location for station old AP b8:62:1f:e5:6a:90-0, new AP b8:62:1f:e9:9f:30-0
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 apfProcessAssocReq (apf_80211.c:4268) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from Probe to AAA Pending
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 20) in 10 seconds
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 START (0) Initializing policy
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state AUTHCHECK (2)
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 AUTHCHECK (2) Change state to L2AUTHCOMPLETE (4) last state L2AUTHCOMPLETE (4)
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 L2AUTHCOMPLETE (4) Plumbed mobile LWAPP rule on AP b8:62:1f:e9:9f:30 vapId 7 apVapId 2
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 0.0.0.0 L2AUTHCOMPLETE (4) Change state to DHCP_REQD (7) last state DHCP_REQD (7)
*Apr 15 17:01:38.144: e0:91:53:60:1f:e4 apfPemAddUser2 (apf_policy.c:213) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from AAA Pending to Associated
*Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Scheduling deletion of Mobile Station: (callerId: 49) in 65535 seconds
*Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Including FT Mobility Domain IE (length 5) in Initial assoc Resp to mobile
*Apr 15 17:01:38.145: e0:91:53:60:1f:e4 Sending Assoc Response to station on BSSID b8:62:1f:e9:9f:30 (status 0) Vap Id 2 Slot 0
*Apr 15 17:01:38.145: e0:91:53:60:1f:e4 apfProcessRadiusAssocResp (apf_80211.c:1957) Changing state for mobile e0:91:53:60:1f:e4 on AP b8:62:1f:e9:9f:30 from Associated to Associated
*Apr 15 17:01:38.189: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
*Apr 15 17:01:38.189: e0:91:53:60:1f:e4 DHCP dropping packet due to ongoing mobility handshake exchange, (siaddr 0.0.0.0, mobility state = 'apfMsMmQueryRequested'
*Apr 15 17:01:39.953: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) State Update from Mobility-Incomplete to Mobility-Complete, mobility role=Local, client state=APF_MS_STATE_ASSOCIATED
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) pemAdvanceState2 4166, Adding TMP rule
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) Adding Fast Path rule
type = Airespace AP - Learn IP address
on AP b8:62:1f:e9:9f:30, slot 0, interface = 13, QOS = 0
ACL Id = 255, Jumbo F
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 DHCP_REQD (7) Successfully plumbed mobile rule (ACL ID 255)
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 0.0.0.0 Added NPU entry of type 9, dtlFlags 0x0
*Apr 15 17:01:39.954: e0:91:53:60:1f:e4 Sent an XID frame
*Apr 15 17:01:40.807: e0:91:53:60:1f:e4 Orphan Packet from STA - IP 169.254.201.128
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP processing DHCP DISCOVER (1)
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP xid: 0x9b24c896 (2602879126), secs: 1280, flags: 0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP processing DHCP OFFER (2)
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP xid: 0x9b24c896 (2602879126), secs: 0, flags: 0
*Apr 15 17:01:43.234: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP ciaddr: 0.0.0.0, yiaddr: 10.6.2.160
*Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP server id: 10.6.15.254 rcvd server id: 10.6.15.254
*Apr 15 17:01:43.235: e0:91:53:60:1f:e4 DHCP successfully bridged packet to STA
*Apr 15 17:01:43.240: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 316, port 13, encap 0xec03)
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP processing DHCP REQUEST (3)
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP xid: 0x9b24c896 (2602879126), secs: 1280, flags: 0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP ciaddr: 0.0.0.0, yiaddr: 0.0.0.0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP requested ip: 10.6.2.160
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP server id: 10.6.15.254 rcvd server id: 10.6.15.254
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP processing DHCP ACK (5)
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP xid: 0x9b24c896 (2602879126), secs: 0, flags: 0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP ciaddr: 0.0.0.0, yiaddr: 10.6.2.160
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:43.241: e0:91:53:60:1f:e4 DHCP server id: 10.6.15.254 rcvd server id: 10.6.15.254
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 DHCP_REQD (7) Change state to RUN (20) last state RUN (20)
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Reached PLUMBFASTPATH: from line 4972
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Replacing Fast Path rule
type = Airespace AP Client
on AP b8:62:1f:e9:9f:30, slot 0, interface = 13, QOS = 0
ACL Id = 255, Jumbo Frames = NO,
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 RUN (20) Successfully plumbed mobile rule (ACL ID 255)
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 Assigning Address 10.6.2.160 to mobile
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 DHCP successfully bridged packet to STA
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 10.6.2.160 Added NPU entry of type 1, dtlFlags 0x0
*Apr 15 17:01:43.242: e0:91:53:60:1f:e4 Sending a gratuitous ARP for 10.6.2.160, VLAN Id 15
*Apr 15 17:01:46.428: e0:91:53:60:1f:e4 DHCP received op BOOTREQUEST (1) (len 308, port 13, encap 0xec03)
*Apr 15 17:01:46.428: e0:91:53:60:1f:e4 DHCP processing DHCP INFORM (8)
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP op: BOOTREQUEST, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP xid: 0xbb0d5d87 (3138215303), secs: 0, flags: 0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP ciaddr: 10.6.2.160, yiaddr: 0.0.0.0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP successfully bridged packet to DS
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP received op BOOTREPLY (2) (len 308, port 13, encap 0xec00)
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP processing DHCP ACK (5)
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP op: BOOTREPLY, htype: Ethernet, hlen: 6, hops: 0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP xid: 0xbb0d5d87 (3138215303), secs: 0, flags: 0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP chaddr: e0:91:53:60:1f:e4
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP ciaddr: 10.6.2.160, yiaddr: 0.0.0.0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP siaddr: 0.0.0.0, giaddr: 0.0.0.0
*Apr 15 17:01:46.429: e0:91:53:60:1f:e4 DHCP server id: 10.6.15.254 rcvd server id: 10.6.15.254
show client e0:91:53:60:1f:e4 (after re-connect)
(Cisco Controller) >show client detail e0:91:53:60:1f:e4
Client MAC Address............................... e0:91:53:60:1f:e4
Client Username ................................. N/A
AP MAC Address................................... b8:62:1f:e9:9f:30
Client State..................................... Associated
Client NAC OOB State............................. Access
Wireless LAN Id.................................. 7
BSSID............................................ b8:62:1f:e9:9f:31
Connected For ................................... 105 secs
Channel.......................................... 11
IP Address....................................... 10.6.2.160
Association Id................................... 8
Authentication Algorithm......................... Open System
Reason Code...................................... 1
Status Code...................................... 0
Session Timeout.................................. 65535
Client CCX version............................... No CCX support
QoS Level........................................ Silver
Diff Serv Code Point (DSCP)...................... disabled
802.1P Priority Tag.............................. disabled
WMM Support...................................... Enabled
U-APSD Support................................... Disabled
Power Save....................................... OFF
Current Rate..................................... m7
Supported Rates.................................. 1.0,2.0,5.5,11.0,6.0,9.0,
............................................. 12.0,18.0,24.0,36.0,48.0,
............................................. 54.0
Mobility State................................... Local
Mobility Move Count.............................. 0
Security Policy Completed........................ Yes
Policy Manager State............................. RUN
Policy Manager Rule Created...................... Yes
ACL Name......................................... none
ACL Applied Status............................... Unavailable
Policy Type...................................... N/A
Encryption Cipher................................ None
Management Frame Protection...................... No
EAP Type......................................... Unknown
Interface........................................ students
VLAN............................................. 15
Quarantine VLAN.................................. 0
Access VLAN...................................... 15
Client Capabilities:
CF Pollable................................ Not implemented
CF Poll Request............................ Not implemented
Short Preamble............................. Implemented
PBCC....................................... Not implemented
Channel Agility............................ Not implemented
Listen Interval............................ 1
Fast BSS Transition........................ Not implemented
Fast BSS Transition Details:
Client Statistics:
Number of Bytes Received................... 36509
Number of Bytes Sent....................... 32902
Number of Packets Received................. 300
Number of Packets Sent..................... 66
Number of EAP Id Request Msg Timeouts...... 0
Number of EAP Request Msg Timeouts......... 0
Number of EAP Key Msg Timeouts............. 0
Number of Data Retries..................... 95
Number of RTS Retries...................... 0
Number of Duplicate Received Packets....... 1
Number of Decrypt Failed Packets........... 0
Number of Mic Failured Packets............. 0
Number of Mic Missing Packets.............. 0
Number of Policy Errors.................... 0
Radio Signal Strength Indicator............ -66 dBm
Signal to Noise Ratio...................... 29 dB
Nearby AP Statistics:
APSOEBFF_COR3(slot 0) .....................
antenna0: 50 seconds ago -91 dBm................. antenna1: 50 seconds ago -76 dBm
APSOEAFF_FAC(slot 0) ......................
antenna0: 108 seconds ago -89 dBm................ antenna1: 108 seconds ago -87 dBm
APSOEBGF_FAC(slot 0) ......................
antenna0: 50 seconds ago -82 dBm................. antenna1: 50 seconds ago -71 dBm
APSOEBGF_STAFF(slot 0) ....................
antenna0: 49 seconds ago -74 dBm................. antenna1: 49 seconds ago -58 dBm
WLAN config
WLAN Identifier.................................. 9
Profile Name..................................... STAFF
Network Name (SSID).............................. STAFF
Status........................................... Enabled
MAC Filtering.................................... Enabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
NAC-State...................................... Disabled
Quarantine VLAN................................ 0
Number of Active Clients......................... 32
Exclusionlist.................................... Disabled
Session Timeout.................................. Infinity
CHD per WLAN..................................... Disabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ staff
WLAN ACL......................................... unconfigured
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Quality of Service............................... Silver (best effort)
Scan Defer Priority.............................. 5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
IPv6 Support..................................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Disabled
Accounting.................................... Disabled
Dynamic Interface............................. Disabled
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
H-REAP Local Switching........................ Disabled
H-REAP Learn IP Address....................... Enabled
Infrastructure MFP protection................. Enabled (Global Infrastructure MFP Disabled)
Client MFP.................................... Optional but inactive (WPA2 not configured)
Tkip MIC Countermeasure Hold-down Timer....... 60
Call Snooping.................................... Disabled
Band Select...................................... Disabled
Load Balancing................................... Disabled
HELPPPP!We have 75 evenly distributed AP's servicing the 500 odd users. Found the below traps on WLC. I was making some changes in the WLAN settings at the time:
Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:8c:a9:82:5d:d2:dc Base Radio MAC :3c:ce:73:c6:fe:00 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
106 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:58:94:6b:f2:24:c8 Base Radio MAC :c8:f9:f9:4c:01:30 Slot: 1 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
107 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:bc:77:37:72:dc:0b Base Radio MAC :3c:ce:73:c6:53:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
108 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:00:26:c7:7d:12:76 Base Radio MAC :3c:ce:73:c4:79:80 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
109 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:bc:77:37:75:1f:93 Base Radio MAC :c8:f9:f9:2b:85:30 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
110 Tue Apr 16 00:03:45 2013 Client Excluded: MACAddress:ac:72:89:58:8e:b9 Base Radio MAC :3c:ce:73:c6:53:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
111 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:bc:77:37:26:cd:e3 Base Radio MAC :3c:ce:73:c5:1f:10 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
112 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:ac:72:89:25:ea:e0 Base Radio MAC :3c:ce:73:c6:77:70 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
113 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:00:24:2c:6a:85:3d Base Radio MAC :3c:ce:73:c6:6a:50 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
114 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:68:5d:43:61:16:51 Base Radio MAC :3c:ce:73:f6:0c:20 Slot: 0 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2
115 Tue Apr 16 00:03:44 2013 Client Excluded: MACAddress:7c:d1:c3:8a:64:f6 Base Radio MAC :3c:ce:73:c4:74:20 Slot: 1 User Name: unknown Ip Address: unknown Reason:802.11 Association failed repeatedly. ReasonCode: 2 -
WLC 5508: 802.1 AAA override; Authenication success no dynamic vlan assignment
WLC 5508: software version 7.0.98.0
Windows 7 Client
Radius Server: Fedora Core 13 / Freeradius with LDAP storage backend
I have followed the guide at http://www.cisco.com/en/US/tech/tk722/tk809/technologies_configuration_example09186a008076317c.shtml with respective to building the LDAP and free radius server. 802.1x authorization and authenication correctly work. The session keys are returned from the radius server and the wlc send the appropriate information for the client to generate the WEP key.
However, the WLC does not override the VLAN assignment, even though I was to believe I set everything up correctly. From the packet capture, you can see that verfication of client is authorized to use the WLAN returns the needed attributes:
AVP: l=4 t=Tunnel-Private-Group-Id(81): 10
AVP: l=6 t=Tunnel-Medium-Type(65): IEEE-802(6)
AVP: l=6 t=Tunnel-Type(64): VLAN(13)
I attached a packet capture and wlc config, any guidance toward the attributes that may be missing or not set correctly in the config would be most appreciated.Yes good catch, so I had one setting left off in freeradius that allowed the inner reply attributes back to the outer tunneled accept. I wrote up a medium high level config for any future viewers of this thread:
The following was tested and verified on a fedora 13 installation. This is a minimal setup; not meant for a "live" network (security issues with cleartext passwords, ldap not indexed properly for performance)
Install Packages
1. Install needed packages.
yum install openldap*
yum install freeradius*
2. Set the services to automatically start of system startup
chkconfig --level 2345 slapd on
chkconfig --level 2345 radiusd on
Configure and start LDAP
1. Copy the needed ladp schemas for radius. Your path may vary a bit
cp /usr/share/doc/freeradius*/examples/openldap.schema /etc/openldap/schema/radius.schema
2. Create a admin password for slapd. Record this password for later use when configuring the slapd.conf file
slappasswd
3. Add the ldap user and group; if it doesn't exisit. Depending on the install rpm, it may have been created
useradd ldap
groupadd ldap
4. Create the directory and assign permissions for the database files
mkdir /var/lib/ldap
chmod 700 /var/lib/ldap
chown ldap:ldap /var/lib/ldap
5. Edit the slapd.conf file.
cd /etc/openldap
vi slapd.conf
# See slapd.conf(5) for details on configuration options.
# This file should NOT be world readable.
#Default needed schemas
include /etc/openldap/schema/corba.schema
include /etc/openldap/schema/core.schema
include /etc/openldap/schema/cosine.schema
include /etc/openldap/schema/duaconf.schema
include /etc/openldap/schema/dyngroup.schema
include /etc/openldap/schema/inetorgperson.schema
include /etc/openldap/schema/java.schema
include /etc/openldap/schema/misc.schema
include /etc/openldap/schema/nis.schema
include /etc/openldap/schema/openldap.schema
include /etc/openldap/schema/ppolicy.schema
include /etc/openldap/schema/collective.schema
#Radius include
include /etc/openldap/schema/radius.schema
#Samba include
#include /etc/openldap/schema/samba.schema
# Allow LDAPv2 client connections. This is NOT the default.
allow bind_v2
# Do not enable referrals until AFTER you have a working directory
# service AND an understanding of referrals.
#referral ldap://root.openldap.org
pidfile /var/run/openldap/slapd.pid
argsfile /var/run/openldap/slapd.args
# ldbm and/or bdb database definitions
#Use the berkely database
database bdb
#dn suffix, domain components read in order
suffix "dc=cisco,dc=com"
checkpoint 1024 15
#root container node defined
rootdn "cn=Manager,dc=cisco,dc=com"
# Cleartext passwords, especially for the rootdn, should
# be avoided. See slappasswd(8) and slapd.conf(5) for details.
# Use of strong authentication encouraged.
# rootpw secret
rootpw
{SSHA}
cVV/4zKquR4IraFEU7NTG/PIESw8l4JI
# The database directory MUST exist prior to running slapd AND
# should only be accessible by the slapd and slap tools. (chown ldap:ldap)
# Mode 700 recommended.
directory /var/lib/ldap
# Indices to maintain for this database
index objectClass eq,pres
index uid,memberUid eq,pres,sub
# enable monitoring
database monitor
# allow onlu rootdn to read the monitor
access to *
by dn.exact="cn=Manager,dc=cisco,dc=com" read
by * none
6. Remove the slapd.d directory
cd /etc/openldap
rm -rf slapd.d
7. Hopefully if everything is correct, should be able to start up slapd with no problem
service slapd start
8. Create the initial database in a text file called /tmp/initial.ldif
dn: dc=cisco,dc=com
objectClass: dcobject
objectClass: organization
o: cisco
dc: cisco
dn: ou=people,dc=cisco,dc=com
objectClass: organizationalunit
ou: people
description: people
dn: uid=jonatstr,ou=people,dc=cisco,dc=com
objectClass: top
objectClass: radiusprofile
objectClass: inetOrgPerson
cn: jonatstr
sn: jonatstr
uid: jonatstr
description: user Jonathan Strickland
radiusTunnelType: VLAN
radiusTunnelMediumType: 802
radiusTunnelPrivateGroupId: 10
userPassword: ggsg
9. Add the file to the database
ldapadd -h localhost -W -D "cn=Manager, dc=cisco,dc=com" -f /tmp/initial.ldif
10. Issue a basic query to the ldap db, makes sure that we can request and receive results back
ldapsearch -h localhost -W -D cn=Manager,dc=cisco,dc=com -b dc=cisco,dc=com -s sub "objectClass=*"
Configure and Start FreeRadius
1. Configure ldap.attrmap, if needed. This step is only needed if we need to map and pass attributes back to the authenicator (dynamic vlan assignments as an example). Below is an example for dynamic vlan addresses
cd /etc/raddb
vi ldap.attrmap
For dynamic vlan assignments, verify the follow lines exist:
replyItem Tunnel-Type radiusTunnelType
replyItem Tunnel-Medium-Type radiusTunnelMediumType
replyItem Tunnel-Private-Group-Id radiusTunnelPrivateGroupId
Since we are planning to use the userpassword, we will let the mschap module perform the NT translations for us. Add the follow line to check ldap object for userpassword and store as Cleartext-Password:
checkItem Cleartext-Password userPassword
2. Configure eap.conf. The following sections attributes below should be verified. You may change other attributes as needed, they are just not covered in this document.
eap
{ default_eap_type = peap ..... }
tls {
#I will not go into details here as this is beyond scope of setting up freeradisu. The defaults will work, as freeradius comes with generated self signed certificates.
peap {
default_eap_type = mschapv2
#you will have to set this to allowed the inner tls tunnel attributes into the final accept message
use_tunneled_reply = yes
3. Change the authenication and authorization modules and order.
cd /etc/raddb/sites-enabled
vi default
For the authorize section, uncomment the ldap module.
For the authenicate section, uncomment the ldap module
vi inner-tunnel
Very importants, for the authorize section, ensure the ldap module is first, before mschap. Thus authorize will look like:
authorize
{ ldap mschap ...... }
4. Configure ldap module
cd /etc/raddb/modules
ldap
{ server=localhost identify = "cn=Manager,dc=cisco,dc=com" password=admin basedn="dc=cisco,dc=com" base_filter = "(objectclass=radiusprofile)" access_attr="uid" ............ }
5. Start up radius in debug mode on another console
radiusd -X
6. radtest localhost 12 testing123
You should get a Access-Accept back
7. Now to perform an EAP-PEAP test. This will require a wpa_supplicant test libarary called eapol_test
First install openssl support libraries, required to compile
yum install openssl*
yum install gcc
wget http://hostap.epitest.fi/releases/wpa_supplicant-0.6.10.tar.gz
tar xvf wpa_supplicant-0.6.10.tar.gz
cd wpa_supplicant-0.6.10/wpa_supplicant
vi defconfig
Uncomment CONFIG_EAPOL_TEST = y and save/exit
cp defconfig .config
make eapol_test
cp eapol_test /usr/local/bin
chmod 755 /usr/local/bin/eapol_test
8. Create a test config file named eapol_test.conf.peap
network=
{ eap=PEAP eapol_flags=0 key_mgmt=IEEE8021X identity="jonatstr" password="ggsg" \#If you want to verify the Server certificate the below would be needed \#ca_cert="/root/ca.pem" phase2="auth=MSCAHPV2" }
9. Run the test
eapol_test -c ~/eapol_test.conf.peap -a 127.0.0.1 -p 1812 -s testing123 -
Deployment of WLC-5508 with 2702i-D have performance issue.
Hi Team,
We have centrally deployed WLC-5508 with 50 AP licence along with HA scenario. we have 3 locations.
1- HQ. have 26 AP with POWINJ5.
2- Branch location A- 8 AP with POWINJ5.
3. Branch location B have 8 AP with POWINJ4.
my exception is to achieve that single SSID with dynamic VLAN from group police (NPS). MY HO have 26 AP and those are working in local mode.
and branches are connected through flexconnect mode. and all are working with different-2 NPS.
Now i am facing a problem with this deployment are following.
1- branch A have performance issue.
2- HQ have performance issue.
3- i don't want to go with dedicated NPS for every location.
In order to achieve this deployment i want only single SSID with primary and secondary NPS at my HQ with dynamic VLAN for respective departmental users vlans..
above is my problem and concern. otherwise i am successfully achieving this solution with dedicated NPS with single group policy. but when i am going forward to achieve my expectation that time i am facing authentication issue at my HQ and sometimes am not able to get proper VLAN IPs. at my HQ.
kindly help me in that to understand where I am doing wrong things to achieve my expectation.
Thanks.
NalinI am facing 2 different problems.
1st issue- in existing setup we have throughput issue. (while downloading or uploading any data from the internet or Intranet, that time wireless clients are facing slowness of the Speed. and same time when i am trying from LAN i am not facing any issue)
2nd Issue- I want to achieve only single SSID with primary and secondary NPS (AD group is bind with vlan Attributes) with dynamic VLAN for respective departmental users.
for Issue no 2 i have created SSID to achieve the single ssid parameter for every location. in order to achieve i have change all access points mode local to Flexconnect mode after that i have created AP groups location wise and then create flexconnect Groups where i have mapped all the vlan through AAA VLAN-ACL mapping. created interface group and mapped all the vlans in that group.
for more understanding please go through the below mentioned CLI view.
Cisco Controller) >show wlan apgroups
Total Number of AP Groups........................ 4
Site Name........................................ GURGAON-AP-GROUP
Site Description................................. GURGAON-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Pol icy
3 gurgaon-interface Disabled None
--More-- or (q)uit
4 gurgaon-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
GUR-AP-01 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:e4 default location 1 IN 1
GUR-AP-05 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b5:18 default location 1 IN 1
GUR-AP-03 2 AIR-CAP2702I-D-K9 bc:16:65:13:71:00 default location 1 IN 1
GUR-AP-07 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:f8 default location 1 IN 1
GUR-AP-06 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:e0 default location 1 IN 1
GUR-AP-08 2 AIR-CAP2702I-D-K9 f4:4e:05:45:78:98 default location 1 IN 1
GUR-AP-02 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b3:2c default location 1 IN 1
GUR-AP-04 2 AIR-CAP2702I-D-K9 f4:4e:05:78:ae:64 default location 1 IN 1
GUR-AP-09 2 AIR-CAP2702I-D-K9 f4:4e:05:80:b4:44 default location 1 IN 1
Site Name........................................ MUMBAI-AP-GROUP
Site Description................................. MUMBAI-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
--More-- or (q)uit
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-7-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:d8 7th Floor 1 IN 3
--More-- or (q)uit
FAL-7-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:18 7th Floor 1 IN 1
FAL-7-AP14 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ad:e8 7th Floor 1 IN 1
FAL-7-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:4c 7th Floor 1 IN 1
FAL-7-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:bc 7th Floor 1 IN 1
FAL-7-AP13 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:80 7th Floor 1 IN 1
FAL-7-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:94 7th Floor 1 IN 1
FAL-7-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:e8 7th Floor 1 IN 1
FAL-7-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:f0 7th Floor 1 IN 3
FAL-7-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:e4 7th Floor 1 IN 1
FAL-7-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:84 7th Floor 1 IN 3
FAL-7-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:b0:14 7th Floor 1 IN 1
FAL-7-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:c8 7th Floor 1 IN 3
FAL-7-AP11 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:08 7th Floor 1 IN 1
Site Name........................................ MUMBAI-THIRD-FLOOR-AP
Site Description................................. MUMBAI-THIRD-FLOOR-AP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
--More-- or (q)uit
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-3-AP07 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:a4 3rd Floor 1 IN 3
FAL-3-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:94 3rd Floor 1 IN 3
FAL-3-AP11 2 AIR-CAP2702I-D-K9 f4:0f:1b:73:00:74 3rd Floor- Eurek 1 IN 3
FAL-3-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:d0 3rd Floor 1 IN 3
--More-- or (q)uit
FAL-3-AP10 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b5:88 3rd Floor 1 IN 3
FAL-3-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:9c 3rd Floor 1 IN 3
FAL-3-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:af:a0 3rd Floor 1 IN 1
FAL-3-AP12 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:fc 3rd Floor- Eurek 1 IN 3
FAL-3-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:28 3rd Floor 1 IN 3
FAL-3-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:f4 3rd Floor 1 IN 3
FAL-3-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:30:92:8c 3rd Floor 1 IN 2
FAL-3-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:30:91:f4 3rd Floor 1 IN 3
Site Name........................................ RAHEJA-AP-GROUP
Site Description................................. RAHEJA-AP-GROUP
Venue Group Code................................. Unspecified
Venue Type Code.................................. Unspecified
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
--More-- or (q)uit
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
5 raheja-interface Disabled None
2 raheja-guest Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location Port Country Priority
FAL-RAHEJA-AP04 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:24:1c Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP02 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:37:3c Confrennce Room 1 IN 3
FAL-RAHEJA-AP03 2 AIR-CAP2702I-D-K9 f0:7f:06:30:93:48 Near Confrence R 1 IN 3
FAL-RAHEJA-AP05 2 AIR-CAP2702I-D-K9 f0:7f:06:bf:ae:c0 Near Meeting Roo 1 IN 3
FAL-RAHEJA-AP06 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:a0 Near Server Room 1 IN 3
FAL-RAHEJA-AP01 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b3:20 Reception Area 1 IN 3
FAL-RAHEJA-AP08 2 AIR-CAP2702I-D-K9 f0:7f:06:8d:25:68 USER BAY ROAD si 1 IN 1
FAL-RAHEJA-AP09 2 AIR-CAP2702I-D-K9 f0:7f:06:92:b4:d4 Training Room 1 IN 1
--More-- or (q)uit
Site Name........................................ default-group
Site Description................................. <none>
NAS-identifier................................... Fractal-WLC1
Client Traffic QinQ Enable....................... FALSE
DHCPv4 QinQ Enable............................... FALSE
AP Operating Class............................... Not-configured
Capwap Prefer Mode............................... Not-configured
RF Profile
2.4 GHz band..................................... <none>
5 GHz band....................................... <none>
WLAN ID Interface Network Admission Control Radio Policy
1 group for mumbai Disabled None
2 guest wifi Disabled None
3 gurgaon-interface Disabled None
4 gurgaon-guest Disabled None
5 raheja-interface Disabled None
6 test Disabled None
Cisco Controller) >show flexconnect group summary
FlexConnect Group Summary: Count: 4
Group Name # Aps
Gurgaon-AP 9
HQ-3RD-FLR-AP-GROUP 12
HQ-7THFLR-AP-GROUP 14
Raheja-AP-Group 8
(Cisco Controller) >show flexconnect group detail Gurgaon-AP
Number of AP's in Group: 9
bc:16:65:13:71:00 GUR-AP-03 Joined Flexconnect
f4:4e:05:45:78:98 GUR-AP-08 Joined Flexconnect
f4:4e:05:78:ae:64 GUR-AP-04 Joined Flexconnect
f4:4e:05:78:ae:e4 GUR-AP-01 Joined Flexconnect
f4:4e:05:80:b3:2c GUR-AP-02 Joined Flexconnect
f4:4e:05:80:b3:e0 GUR-AP-06 Joined Flexconnect
f4:4e:05:80:b3:f8 GUR-AP-07 Joined Flexconnect
f4:4e:05:80:b4:44 GUR-AP-09 Joined Flexconnect
f4:4e:05:80:b5:18 GUR-AP-05 Joined Flexconnect
Efficient AP Image Upgrade ..... Disabled
Master-AP-Mac Master-AP-Name Model Manual
Group Radius Servers Settings:
Type Server Address Port
Primary Unconfigured Unconfigured
Secondary Unconfigured Unconfigured
--More-- or (q)uit
Group Radius AP Settings:
AP RADIUS server............ Disabled
EAP-FAST Auth............... Disabled
LEAP Auth................... Disabled
EAP-TLS Auth................ Disabled
EAP-TLS CERT Download....... Disabled
PEAP Auth................... Disabled
Server Key Auto Generated... No
Server Key.................. <hidden>
Authority ID................ 436973636f0000000000000000000000
Authority Info.............. Cisco A_ID
PAC Timeout................. 0
Multicast on Overridden interface config: Disabled
DHCP Broadcast Overridden interface config: Disabled
Number of User's in Group: 0
Vlan :........................................... 203
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 205
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 204
--More-- or (q)uit
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 206
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 207
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 208
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 209
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 210
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 211
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 212
Ingress ACL :................................... None
Egress ACL :.................................... None
--More-- or (q)uit
Vlan :........................................... 216
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 217
Ingress ACL :................................... None
Egress ACL :.................................... None
Vlan :........................................... 218
Ingress ACL :................................... None
Egress ACL :.................................... None
Group-Specific FlexConnect Wlan-Vlan Mapping:
WLAN ID Vlan ID
WLAN ID SSID Central-Dhcp Dns-Override Nat-Pat
(Cisco Controller) >
(Cisco Controller) >show wlan summary
Number of WLANs.................................. 6
WLAN ID WLAN Profile Name / SSID Status Interface Name PMIPv6 Mobility
1 FRACTAL-EMP-MUMBAI / FRACTAL Enabled group for mumbai none
2 FRACTAL-GUEST / FRACTAL-GUEST Enabled guest wifi none
3 FRACTAL-EMP-GURGAON / FRACTAL-GURGAON Enabled gurgaon-interface none
4 GURGAON-GUEST / FRACTAL-GUEST-GURGAON Enabled gurgaon-guest none
5 RAHEJA-EMP-WIRELESS / FRACTAL-R Enabled raheja-interface none
6 TEST-SSID / TEST-SSID Enabled test none
hope this will give you proper understanding.
Maybe you are looking for
-
Hi, I've authored a number of DVDs sucessfully with DVD studio pro but never a multiangle project. I'm looking for some recommendations, and for some direction in the output from FCP via compressor to DVDSP in order to provide for 3 to 4 angle viewin
-
my itunes worked fine yesterday yet today it won't open, everytime i try to open it, it says The instruction at "0x10001040" referenced memory at "0x10001040". The memory could not be "read". i have restarted my computer, i have reinstalled itunes, t
-
Create a function in my page model header
Hi everybody, I'm trying to do a function. This is my function : function Test() if(document.getElementById(item.value != "") put my item disabled Element <i>p32_id_feuillet</i> html form element attributes <b>onClick="javascript:Test();"</b> How I c
-
Since I installed Mountain Lion my computer will not sleep. This appears to be a different problem from what others are experiencing. Unlike what has been referred to on other threads, all items in my Apple menu (except Sleep) are functioning norma
-
No frames visible in Reports 2.5 Layout on Win2000
Hello: I upgraded my OS to Win2000 and run Reports 2.5. I am unable to see the frames in the layout editor (the reports displayed/worked fine on Win 98). Please help. Thanks Peter