Wonderware and OPC; reading arrays ?

I have a contact on a project that says Wonderware is not able to read
OPC data (Shared Variables) from LabVIEW in the form of arrays of double, all data must be single values.
Can anybody confirm this statement, or tell me otherwise ? I find it strange that
this big software platform in the year of 2015 cannot read arrays of OPC data.
Martin

Hi Martin,
and in which way can LabVIEW help when "Wonderware is not able to read OPC data (Shared Variables) from LabVIEW in the form of arrays of double" as you wrote?
That sounds like a problem of Wonderware - and you should ask the support for Wonderware…
Best regards,
GerdW
CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
Kudos are welcome

Similar Messages

Reading arrays of double from S7 with OPC & Datasocket

Hi friends:
We are developing an application with a S7-315-2DP PLC and a PC with a PCI1500PFB. We use the OPC server from Applicom. We read the data very quickly with the datasocket (arrays of boolean, arrays of doubles ...and so on, and a very big amount of data over 100 ms) but when we try to write arrays datasocket faield and we have to write item on item and the speed decrease. For intance, if we try to write doubles ( 50 items) the refresh period is over 5 seconds ( some times more since we launch the data and we read the same data on the PC). Perhaps we failed configuring the OPC but there isn´t many things to configure, perhaps the problem is the board configuration .. I don´t know.
We
try to find some examples that write an array of doubles on one time but..
Thank you for yours answers.
Javi

Hi Javi,
I'm not aware of any known issues writing to the Applicom OPC server. In LabVIEW there isn't anything special you need to configure to be able to write arrays of doubles through DataSocket. You can test this by using the DataSocket Server Manager, make a new member that is an array of doubles, and try reading and writing to that member. You may also want to check to make sure the data member the OPC server is expecting is an arry of doubles and not an array of singles or integers.

Reading a CSV file and producing an array of objects

Hi everybody,
I am writing an application which will read a cvs file and produce an array of objects.
Can any body help me to solve this problem?
Thanks
Finny

Hello,
Have you tried this link?
http://ostermiller.org/utils/CSV.html

Help! How to read a .txt file into a Java class and make 2D array?

Hi guys,
Im a newbie with arrays, just started really using them.. please bear with me if I don't seem to understand much..
I have a .txt file that contains either a square or rectangle (random width and length).. How can I read each line into a Java class into a 2D array with rows and columns?

Example :
import javax.swing.*;
import java.util.ArrayList;
import java.io.BufferedReader;
import java.io.FileReader;
import java.io.File;
public class ReadInto2DArrayExample {
    public static void main(String[] args) {
        ArrayList array = new ArrayList();
        char [][] twoDimesionArray = null;
        try
            JFileChooser fileChooser = new JFileChooser();
            if (fileChooser.showOpenDialog(null) == JFileChooser.APPROVE_OPTION)
                File file = fileChooser.getSelectedFile();
                BufferedReader reader = new BufferedReader(new FileReader(file));
                String data;
                //Read from file
                while ((data = reader.readLine()) != null)
                    //Convert data to char array and add into array
                    array.add(data.toCharArray());
                reader.close();
                //Creating a 2D char array base on the array size
                twoDimesionArray = new char [array.size()][];
                //Convert array from ArrayList to 2D array
                for (int i = 0; i < array.size(); i++)
                    twoDimesionArray[i] = (char [])array.get(i);
                //Test the 2D Array
                for (int y = 0; y < twoDimesionArray.length; y++)
                    char [] temp = twoDimesionArray[y];
                    for (int x = 0; x < temp.length; x ++ )
                        System.out.print(temp[x]);
                    System.out.println("");
        catch (Exception ex)
            ex.printStackTrace();
}

Reading in a binary file and displaying an array correctly

I am teaching myself Labview 7.1 and what I am trying to do is read in a text file of binary digits 10011001, 11011101 etc and then output these to a series of leds (boolean array) as well as to another array to display what was read in. I can get this to happen when I format the text file as 1,0,0,1,1,0,0,1 but then the array is 1 column by 8 rows (is this a 1by8 array) I want to read this data in as 10011001 displayed on 1 row and then the next row of the array to be 11011101, it displays 11111111 if I go above 3 digits, I know this is just a problem with binary versus decimal numbers, how can I format the input file so it is read in as 8-bit binary?
Thank you in advance,
Dan Ziehm

Read the text file as string, then pass it through "spreadsheet string to array" with "," as delimiter, %b as format and an U8 array as type. I made a quick demo, see attached code image.
LabVIEW Champion . Do more with less code and in less time .
Attachments:
binaries.gif ‏45 KB

How to read XI Data type in Java code and populate as array list, using UDF

Hi,
How to read XI Data type in Java code and populate as array list, using UDF?
Is there any API using which the XI data types can be read?
Kindly reply.
Richa

Input Structure:
<?xml version="1.0" encoding="UTF-8"?>
<ns0:CustomerCreateResp xmlns:ns0="urn:bp:xi:up:re:cust_mdm:cmdm:pr5:100">
   <CUSTOMER>
      <item>
         <CUSTOMERNO/>
         <MDMCUSTOMER/>
         <CREATE_DATE/>
         <RETURN>
            <TYPE/>
            <MESSAGE/>
         </RETURN>
         <PT_CONTPART_RETURN>
            <item>
               <MDM_CONTACT/>
               <CONTACT/>
            </item>
         </PT_CONTPART_RETURN>
         <PARTNERS>
            <item>
               <CUSTOMERNO/>
               <PARTNER_FUNCTION/>
               <PARTNER_NUMBER/>
               <DEFAULT_PARTNER/>
            </item>
         </PARTNERS>
      </item>
   </CUSTOMER>
</ns0:CustomerCreateResp>
Output structure
(Sample output structure.This actually needs to be mapped and generated using UDF)
<?xml version="1.0" encoding="UTF-8"?>
<ns1:updateCustomer xmlns:ns1="urn:xiSericeVi"><ns1:customer><ns2:ArrayList xmlns:ns2="java:sap/standard">[]</ns2:ArrayList></ns1:customer><ns1:name>2344566</ns1:name></ns1:updateCustomer>

Why are my Datasocket OPC reads and writes so slow?

I am creating an application (in LabView 6.1) that has to interface with 15-30 OPC tags (about half and half read and write) on a KepWare OPC server. It seems like the DSC Module would be overkill, but the datasocket write VIs seem to slow the system to a halt at about 6 tags. I saw something about using the legacy datasocket connect VIs, but would I really see a large performance boost from switching?
In the existing code we have, I have seen that even the legacy VIs (our old code uses the older VIs) sometimes grind the system to a halt or lock it up completely if it loses sight of the OPC server. Has anyone else had problems with this?

Hi IYUS,
What OPC Server are you using? What methods are you using to communicate? If you are using IAOPC, have you installed the latest patch?
Also, this post is nearly 2 years old. You will probably get more visibility (and more help) if you post your questions in a new thread.
Cheers,
Spex
National Instruments
To the pessimist, the glass is half empty; to the optimist, the glass is half full; to the engineer, the glass is twice as big as it needs to be...

Anyone know how to add a string to a 1d array with file info, then be able to read back, display string, and sort data array.

I need to store a data array and include text that describes what the data is. (using for various configuration files.) Anyway, I would like to be able to save the string as part of the txt file, and somehow read it back, remove the (various length string), and display it in an indicator. All the while, not causing too much problem with the initial data array.
Thanks in advance!!

There are several ways to do what you require. A simple method would be to use an ASCII text file. When writing one of those, you just need to basically build a gaint string starting with the description text you want. We like to call that a header. Once you've got the header, make some sort of delimiter like a bunch of "-" or two sets of ( EOL = End of Line = CRLF = \r\n ). After your delimiter, concatenate your array in string form or flatten your array from its native form into a string and tack it on the file (append).
See the (very quick) example attached.
Dan Press
www.primetest.com
Attachments:
fileheader.vi ‏41 KB

Raid 0 Failure! XP Pro won't read array on MSI k7T266 pro2 *URGE

Before anything else, thanks for reading and I hope you can help:
I have an MSI k7T266 Pro2A-RU motherboard with 512MB of Mushkin RAM, AMD XP 1600+, a Geforce2 MX400, Audigy Soundcard and a cheap PCI NIC card. I consider myself an above average technician and I've come up on a problem I can't figure out. There is about 80GB of data at stake here:
I have 2 IBM Deskstar 40GB 7200 RPM drives that were configured in a RAID 0 (stripe) configuration over a year and a half ago. This gave me a total of 80GB online. Windows XP Professional was installed and the drives have been running fine every since...
The system was practically bulletproof and it was very rare it ever locked up for any reason. A few days ago, however, the system locked up about 4 or five times. There was no software or hardware that had been added or installed and system use hadn't really changed up or down. I run up to date antivirus software (Command Anti-Virus), run behind a secure firewall and watch what I open. The lock ups were random, but happened when I was away from the computer. ( I leave my system on all the time).
Being a bit paranoid, on 1/28/03, I acquired an 80GB Maxtor drive to install to back up my datafiles. Before the install, I notice the system had locked up at least once that day, so I figured I would hurry up and get the drive in to back up. I installed the 80, booted, configured it in XP and made it active and transfered a few test files over. No problem. I made the decision to back up my data files before bed and continued to work for the next two hours. The system ended up locking up with a windows blue screen STOP error message: KERNEL_FAULT_INPAGE_ERROR when I tried to run a program. Thinking little of it, I rebooted the computer to find I could no longer access the data on the RAID.
I've tried nearly EVERYTHING I can think of. (You can already assume I've done the basics (check/replace the cables, etc). Here's a list and the results:
---- Reboot in all available modes (Safe, Safe with NW, Normal, Last known, etc). They all FAIL. In safe modes, you can see where the system actually tries to boot off the array (runs through driver files and stops on MUP.SYS) and hangs. Same result with all other drives removed except the RAID.
---- Installed another drive, loaded XP with the raid controller files (By the way, it's a Promise ATA 100 "lite" controller), plugged the RAID back in and it hangs on boot up. Safe mode gives the same results. Tried the same thing with Windows 2000 (so I could access the NTFS partition) and Windows 2000 won't load when the array is plugged in, but loads ok when it isn't (used the 2000 driver for the RAID controller for this attempt). Safe mode gives the same results.
---- Removed all drives except the Array and tried to reload XP (with the array drivers downloaded again from the site.) No effect. System hangs.
---- In a last ditch effort, I have access to Winternals Administration Pack 2002 of all of their tools. ERC Commander, designed for this type of problem, Disk Commander, and the other tools all do the same thing: Any time the system attempts to read from or access the arry, the OS will hang. It won't even check for NTFS compatibility in the ERC commander program booting from a boot CD, and for those that are familiar with it, the Disk Commander program blue screens with a STOP: 0x000007B (0xF896963C, 0xC0000034, 0x0, 0x0) error. Research has told me this is an INACCESSABLE BOOT DEVICE message.
These are the main highlight major attempt things and there's a few things in between I've tried (like using Norton Ghost to try and mirror the array to the 80GB. Norton ghost said there is an error reading the partition and can't go any further (Returns an Internal error))
I'm at the point where I have run out of available options and don't know what else to try. I have since purchased the exact same motherboard off e-bay to see if it just so happens to be the controller and to see if my RAID will come back so I can at least read the data off of it. It should be here in a few days. If that doesn't work, I'm toasted. Could I be fighting a hardware (drive or board or controller) problem. Is the array THAT corrupt the OS can't read it???
If anyone has any other bright ideas, I'm willing to try about anything short of damaging the array. Any help is greatly appreciated. Please post here, or e-mail to [email protected].
BTW, the Promise BIOS is Fasttrak 100 "Lite" v 1.31.1(Build 30)
Thanks.
- Chuck! ?( ;( ;( ;( ;( ?(

got one but its lightley used for storage but amd forum storage is full of tales of woe with them
type deskstar and problems in goggle for a laugh

How to create and use mutable array of UInt8

Hello!
If I get it right, UInt8 *buffer, buffer - is a pointer to a start of array?
Then how to create and use mutable array of UInt8 pointers?
The main target is a creation of the module that will store some byte array requests and will send all of them at the propriate moment.

I try
- (void) scheduleRequest:(UInt8 *)request {
if (!scheduledRequests) scheduledRequests = [[NSMutableArray array] retain];
[scheduledRequests addObject:request];
But get warning:"passing argument 1 of 'addObject:' from incompatible pointer type"

I am looping and through an array comparing two bigdecimals:

I am looping and through an array comparing two bigdecimals:
I get the max for valueB only if I have multiple items. not when I have one item why would that be:
val=0;
if (array.compareTo(valueB) > 0) {

Hi. You were wise to trace the value of n. Your problem seems
to be that the tests succeed (almost always) in the very first
iteration because they truly don't match (where n = 0) and
execution breaks out. You need to adjust the logic. As one
approach, while sticking with your code and not changing it too
much (such as using more efficient int vs Number):
at the very top, define a counter var ct:int = 0;
before the testing loop, define a flag, such as var
flag:boolean = false;
you could then invert the logic in the loop and test for ==
rather than for !=
if you find a match, do--> flag = true;
and break
at the end of testing, use the flag to decide whether to
store the new value
if (!flag) {
// add to array
ct++;
also, use a while loop for controlling the whole thing-->
while(ct < max) { }
to know when you're done
You can also check out the Array functions indexOf() and
some(), to make things more efficient and faster/easier
when you're all done, you can also look into using if (a != b
&& c != d)
for efficiency, instead of nesting them separately
good luck :)

Can you please put me in touch with the support for the trial copy of adobe acrobat XI pro which I had tried out on March 15 for 30 days. I have been trying to cancel since the cost is too much and Acrobat Reader is OK for me. I can't find uninstaller.

Can you please put me in touch with the support for the trial copy of adobe acrobat XI pro which I had tried out on March 15 for 30 days. I have been trying to cancel since the cost is too much and Acrobat Reader is OK for me. I can't find uninstaller.
I have had to erase my disk since then with trouble with Apple Store not recognising my machine and the reload from Time Machine has given complications . Can you please cancel my trial and return my Trial money.

If you paid for what you used then it was not a trial.
Look thru the following links and use the chat option if required for your situation:
Cancel your membership or subscription | Creative Cloud
https://helpx.adobe.com/x-productkb/policy-pricing/cancel-membership-subscription.html
https://forums.adobe.com/thread/1703848
Chat support - For the link below click the Still Need Help? option in the blue area at the bottom and choose the chat option...
Creative Cloud support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html ( http://adobe.ly/19llvMN )
Phone support | Orders, returns exchanges
http://helpx.adobe.com/x-productkb/global/phone-support-orders.html

Using join and batch reading in the same query

Hi,
I wonder if it is possible to use "Joining" and "batch reading" in the same query.
For example I Have
A -> 1-1 B
A -> 1-1 B
B -> 1-M C
This is the case where I have two separate 1-1 relationships to the same class B from A. Toplink 10.0.3 can manage it nicely through joining.
Now, I would like to read a set of As (with its 2 Bs) and all Cs for each B.
It seems that the following configuration does not work:
A -> 1-1 B (use joining)
A -> 1-1 B (use joining)
B -> 1-M C (Batch read)
Any help would be greatly appreciated
Tony.

James,
Would you be so kind to look at the following code?
Am I formulating it correctly to achieve my desired behavior?
Trip.class -> 1-1 PickupStop
Trip.class -> 1-1 DropoffStop
PickupStop and DropoffStop extend Stop and use same table (STOP)
Stop -> 1-M StopEvents
I would like to fetch all Trips, with their Stops and all StopEvents in 2 queries:
1. Trip joined with Stop
2. Batchread StopEvents
Code:
ReadAllQuery raq = new ReadAllQuery(Trip.class);
Expression qexp1 = new ExpressionBuilder();
Expression qexp2 = new ExpressionBuilder();
raq.addJoinedAttribute("pickupStop");
raq.addJoinedAttribute("dropoffStop");
raq.addBatchReadAttribute(qexp1.get("pickupStop").get("vStopEvents"));
raq.addBatchReadAttribute(qexp2.get("dropoffStop").get("vStopEvents"));

HT1695 I know nothing about how to use my new ipod and when reading the little bit of information in the folder that came with it, all I can do is turn it on, but it just powers down after a few seconds. How do I work this thing?

I know nothing about how to use my new ipod and when reading the little information that came with it, all I can do is turn it on. Then in a few seconds it goes black, never having brought up a screen to do anything! Help! What do I do to get this thing going?

You might consider connecting it to the charger and charging up the battery overnight.
Please Get the iPod Touch User Manual for iOS 5

With OSX10.7.5 and Adobe Reader 11.0.02 when I try to open a PDF downloaded from the web I get 'There was an error opening this document. This file is damaged and could not be repaired. Preview will not open either. Older PDFs OK.

I am running OS X 10.7.5 and Adobe Reader 11.0.02. In the last few days I have been unable to open PDF's downloaded from the web. Reader gives the error message 'There was an error opening this document. The file is damaged and could not be repaired'. Removing Reader and trying to use Preview to open these files give the error 'Preview cannot open this file. It may be damaged or use a file format that Preview doesn't recognise' (or something like that). Downloading the same files with Reader removed from my Mac Preview opens the files OK.
I was recently prompted to update Adobe software but did not note exactly what the update was nor when it was done.
Reader and Preview will both open PDFs I downloaded a week ago. Reader will also open files downloaded on another Mac running OS X 10.0.0 and copied to my Mac. Any ideas?

Back up all data.
Triple-click the line of text below to select it, the copy the selected text to the Clipboard (command-C):
/Library/Internet Plug-ins
In the Finder, select
Go ▹ Go to Folder
from the menu bar, or press the key combination shift-command-G. Paste into the text box that opens (command-V), then press return.
From the folder that opens, remove any items that have the letters “PDF” in the name. You may be prompted for your login password. Then quit and relaunch Safari, and test.
The "Silverlight" web plugin distributed by Microsoft can also interfere with PDF display in Safari, so you may need to remove it as well, if it's present.
If you still have the issue, repeat with this line:
~/Library/Internet Plug-ins
If you don’t like the results of this procedure, restore the items from the backup you made before you started. Relaunch Safari again.

Wonderware and OPC; reading arrays ?

Similar Messages

Maybe you are looking for