WRT160NL and XBOX + AP issues

I've installed a WRT160NL in my home as the main router. I've correctly set up the wired network and also the wireless one, as long as I get Internet access with all my devices: desktop PC, netbook, iPod Touch and XBOX console. With this last device I'm having some speed problems. I connect the XBOX to the WRT160NL through a Conceptronic C54APM Access Point. The console has Internet access but it's really slow. I've activated the UPnP Media Server on the router to access to the shared USB external link, but the reading of directories is extremely sloooow.
I would like to know which is the protocol used by the WRT160NL to share the contents of the HD I've attached in the "normal" sharing mode and also in the UPnP. The console has several sharing formats supported, but I don't know id the offered by the Linksys is SMB, NFS, etc.
Thanks in advance for your help!!
Vuela, vuela, V.O.M.I.T.O.N.!!!

Are you facing the Low connectivity on your other computer also while accessing the internet on PC, Noteboot, IPOD? or you are just facing the problem with your XBOX. Have you tried to mapp the drive on your computer and check if its still working on your computer also? If it works perfectly fine on your PC's then i think you need to check the settings on Conceptronic C54APM access point.

Similar Messages

BEFW11S4 V4 and Xbox 360 issues

Back when I had Halo 3, I could play and lag would be the only problem. I recently got FFXI however and I keep getting a 0250 error. A lot of people tell me I need to forward my ports but I don't think that's it since I didn't have to do that for Halo 3. Others say it may be a firmware thing. When I try to update the file, it just fails and I don't know how to fix that.
Is it my router that's causing this problem or is it the server's problem (Sometimes the issue with FFXI and the same error) either way, I'm losing day by day on my free trial and I can't update the game because of the error.

For Firmware Upgrade try this :
Download TFTP Utility
Download Firmware 314 KB
Double click the tftp.exe file and click run :
For Server- Enter the IP Address of the router that you assigned. By default, the router is 192.168.1.1...
For Password- Enter the password you assigned the router. By default, the router’s password is “admin”.
For File- Click the triple “…” button and browse for the .bin firmware file...
Click Upgrade button to start upgrading. A progress bar should show up to show the progress.
Once the Upgrade is done press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
You should also open the Ports on your router...
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 53, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in PQR, in the start box type in 88 and End box type in 88, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in XYZ, in the start box type in 3074 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings...
4) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
5) Click on set-up and change the MTU Size to 1452 and click Save Settings...
6) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
7) Also assign the DNS Addresses on the Xbox
Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
8) Turn off your modem, router, and Xbox...Wait for a minute...
9) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Newest 3TB Time Capsule with Motorola SB6121 and Xbox live issues.

I just bought a new 3TB Time Capsule but am having issues with the speed of my internet and connecting to XBL. I use Time Warner and have a Motorola SB 6121 modem. The modem is brand new as well and worked perfeclyt with my old router(Trendnet TEW-gr633). I want to use the time capsule as my only router but it is only testing out between <1-2 on the download. I was getting 15-25 on the download before the TC. I am also having issues connecting to the network on my xbox 360S as well.
Any help with adjusting the settings on my TC would be much appreciated.

I would suggest adjusting the Time Capsule's Ethernet WAN port setting using the AirPort Utility. By default, this option is set to Automatic. I would recommend changing it to "1000 Mbps / Full Duplex" to see if this helps.
ref: AirPort Utility > Select the TC > Manual Setup > Internet > Internet Connection tab > Ethernet WAN Port

Fios and xbox live issues

Ok well ive read all the stuff on the internet about updating the firmware and it should work. My problem is I have the Gen 2 router, so the firmware isnt compatible at all. Im not even trying to do xbox live wirelessly, i have an ethernet ran. My wireless laptop and my wired desktop computer have been running awesome internet since I got FiOS installed about 4 months ago. Just got my xbox and now im having these issues. Ive tried restarting both the router and the xbox, ive set the router settings back to default. idk what to do, help me out!!!
edit- thru the xbox network connection wizard thing, it looks like its not even seeing a connection at all. could it be i have the wrong type of cable? i just bought it, its a belkin fastcat 5e patch cable. is this the right type of cable?
Message Edited by CRZYairBORNE on 08-08-2009 03:18 PM

Cable type is fine.
Couple things to check....
make sure the cable is plugged into one of the lan ports on the router (yellow plugs) not the wan connection (white plug). Easy to make the mistake if you have coax style internet via fios.
If connected correctly, do a quick loop test with the cable to make sure that cable is ok. Take both ends of the cable and plug both ends into the router. for example, plug end one in port one and end two in port two. make sure that both lights light up. If not likely bad cable. If so, cable is likely OK.
If cable tests OK, and you have it connected correctly to the lan, then the problem is likely with the Nic on the Xbox. Try going into the network settings in the xbox and reset to defaults on the xbox.
====================================================================================
Error exists between keyboard and chair.

WRT160Nv2 And Xbox NAT Issues

MY xbox runs on the 192.168.0.0 network while my internet connection runs off of the 192.168.1.0 network. So when I open my ports they're being opened for my computer connection. But even doing this doesn't open my NAT. I've tried to put my xbox on the 192.168.1.0 network too and this only causes me to lose my internet connection as a whole. What should I do?

You connected the xbox to your computer?? With ICS (internet connection sharing)? In that case you have two routers between the xbox and the internet: the WRT and your computer. You have to forward the necessary ports from the internet to the computer on the WRT and then on the computer to the xbox. I kind of doubt that will work very well.
You should try to bridge the wireless connection and ethernet connection on the computer instead of using ICS. Then your xbox connects directly to the WRT LAN and needs a 192.168.1.* address then. Port forwarding is only necessary on the WRT then.
Of course, I would recommend to get a wireless adapter for your xbox to connect directly to your WRT instead of going through the computer. Going through the computer only makes the connection quality worse...

E3000 and Xbox Live Issues

Hi All,
So I originally had problems with my xbox where the wireless would drop out. I chaned some settings and I also set up port forwarding for my xbox which seems to have stabilized my network. However, when attempting to download certain files from xbox Live, my router will frequently freak out, reset (so all network connectivity disappears) and after a few moments, everything comes back up again.
I have the xbox 360 as the only device accessing the 5ghz wireless network. Network mode is "Mixed", Channel Width is "Auto", Channel is curently set to "36" as before it ws also set to "Auto DFS" but experienced more frequent drop-outs when simply logging into xbox Live. Again, SIngle Port Forwarding for just this device is enabled. Anyone have any other suggestions? Should I try a different Channel?
Thanks,
DB

I have plenty of other wireless devices (2 iphones, a mac mini, laptop). Whats the advantage of moving everything over to the higher bandwidth when everything Ive been told suggests that you dont want to crowd the higher bandwidth with devices that shouldnt and cant take advantage of the higher bandwidth? I mean, why did I spend money on this router to begin wth if it cant even support the devices I have now? Sorry, this is more than a little frustrating and I guess I would still like to hear some more ideas of what to try.

New Fios G1100 and Multiple Xboxs Connected to xbox live issues.

I just upgraded my router from the Actiontec MI424WR to the G1100. Now I am into an issue with Fios keeping a connection to xbox live on selected xbox devices. I have 3 xbox 360 and 2 xbox one connecting to the network. Both Xbox One maintain solid connection to live, but the 360 experience I have a totally different experience. My set up has 1 Xbox One Wired, 1 wireless. I have 2 xbox 360 wireless and 1 wired. I am also experiencing problems with one of my desktops which is wired that randomly loses a connection to internet. I been using this TRENDnet 8-Port 10/100Mbps GREENnet Switch (TE100-S80G) to help with wired connections. Both Xbox Ones on the network remain connected at all times, or at least I haven't seen a drop. My experience with my xbox 360s are completely different from my Xbox One.They all drop connection randomly every 5 to 20 min. I can immediately sign back in , but this continuosly happens. I was able to get one xbox 360 to maintain a continuous connection by putting it IP address and enabling DMZ on it. I have tried port forwarding but that doesn't work. Anybody have any suggestions or solution? Or should I just shipped back the G1100 and go back to Actiontec MI424WR.

Who is your ISP...?
Are you getting any error message...?
Try the following settings and check..
Open the router setup page,On the set-up tab change the MTU Size to 1365 and click Save Settings...Click on "Administration" tab and disable the option UPnP and click Save Settings...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 53 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box, click Save Settings once done...
2) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
3)Click on the Status tab and take note of DNS1 and DNS2 Addresses...
4) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
5) Also assign the DNS Addresses on the Xbox
Use DNS1 and DNS2 Addresses you took note off of the router status tab as Primary DNS & Secondary DNS for the xbox...
6) Turn off your modem, router, and Xbox...Wait for a minute...
7) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Updated to 7.3.1, PC and Xbox 360 can't connect

Hey, anyone else having problems getting PCs and Xbox 360s to connect to the AirPort Extreme after the 7.3.1 update? Wired or wireless, my PC (Vista, with and without SP1) and my Xbox 360 (with the official wireless network adapter) won't connect.

I am in the same boat...
7.2 worked great... 7.3.1 does not even show in the network list. Also, downgrading it does not fix the issue?!?!?
- Jay

WRT54GX4 Wireless Router and Xbox 360 Wireless Networking Adapter

I just got an Xbox 360 with a Wireless Networking Adapter. The adapter will recognize the network, but won't connect to it. Even if I remove the security, the Xbox 360 won't connect. Is there something else via the router I'm supposed to be doing? I called Microsoft and they said to open the port settings, but I don't know if that's really the issue and I don't know how to do that if I need to.
The ports they gave me were:
TCP 80
UDP 88
UDP 3074
TCP 3074
UDP 53
TCP 53
Thanks for any help if you can.

Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 88 and End box type in 88, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in PQR, in the start box type in 3074 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in XYZ, in the start box type in 53 and End box type in 53, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings...
3) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
4) Click on set-up and change the MTU Size to 1452 and click Save Settings...
5) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
6) Also assign the DNS Addresses on the Xbox
Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
7) Turn off your modem, router, and Xbox...Wait for a minute...
8) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Gmail/Exchange email and calendar syncing issues

I have wiped my email accounts several times and entered in my data in the various ways as shown through the forums but my email accounts do no sync properly whether it is manual or active synced.
I read my emails in my gmail and my Microsoft exchange account and will delete or file them away but then when I check my accounts on my desktop, they are not synced as I've done so on my phone. I've also noticed that my calendars are not synced correctly either.
Could someone help me understand why and how these issues can be fixed? I'm in meetings for most of the day so I rely on my phone to keep me mobile. Was this a bad purchase?!?!

Hi JadeyMU,
How do you have your Microsoft Exchange account configured on your BlackBerry Z10? Are you using ActiveSync, BlackBerry Enterprise Server (BES), IMAP or POP?
Thanks.
-CptS
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

My experience with Apple TV and HDMI/HDCP issues

I am convinced that it is the software update to 4.2.2 from 4.2.1 that is causing this issue. All forms of applications only worked once for me and then it reverted back to HDCP issues. I read several postings everywhere including plenty at Apple's forum and AVS where people were very frustrated with this HDCP issues. Anyways, here is what I did before taking it back to Apple store....I bought AUVIO high speed cables from Radio Shack which is rated very high and tried that and I still got HDCP issues when using NetFlix or AirPlay from iPad. Youtube from Apple TV always worked well without HDCP complaints.
I packed everything back and took it to Apple Store (you can return without re-stocking fee up to 14 days from the day of purchase). After 14 days, you cannot even return it and you can ONLY fix it. I waited for a Technician. They heard my complaints but didn't refute any of it (possibly because they have had numerous complaints on this product). It took 5 minutes inside for them to test and see similar issues with the box that I had. So, they have swapped it for a new box. Before I left the store, I checked the settings including software version and Audio/Video settings in the Apple TV that is connected at the store. I found three main differences none of which the Apple customer service staff agreed could be the reason for my problems (surprise!!)
1. The software update from the shelf and the one they were using was NOT updated to 4.2.2 (it was still running 4.2.1)
2. Because of the software update, the Audio/Video setting for HDMI had the options to toggle between Auto, RGBy, RGBhi & RGBlo bandwidth. I believe this was in place to make the HDMI interface output as component with higher or lower bandwidth but the newer update will ONLY give you the Auto option (!!!)
3. They had this directly Ethernet wired and not through Wireless network and were recieving the all the full bar strength signals. On the box that I returned, eventhough I have 18 Mbps speed at the house (any given time of the day), the Network speed test was taking a long time. Moreover, after the Apple TV network test, it doesn't spit out the outcome of the tests (a BIG bummer and useless for testing).
Anyways, I took the new box and hooked it up directly to my SONY BRAVIA XBR3 TV to one of the HDMI ports, disabled the feature to send or recieve data to Apple directly and did NOT update the software. It worked fine and have tested all of the options. From what I have read so far (I have only spent 30 hours of my weekend on this when Apple product hookups are supposed to take 5 minutes ONLY), there is NO guarantee that it will work continuously as people have had things work on them for 6 months and then suddenly have the HDCP issues.
Will wait to see....if it continues to work....

I figured it out. Had to go to general settings on the main screen and restart. Synch of audio is much better.

I have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3

i have a serious (and bizarre!) issue with my novation impulse (Although i've tried it with two other keyboards and i still have the same problem) and its compatibility with mainstage 3.
the problem is best explained on the following one - page thread:
https://discussions.apple.com/thread/3951518?start=0&tstart=0
(Clearly i'm not alone in this problem, although i think i figured out what's going wrong a little more than he did...read on!)
his solution, to put mainstage in jump mode, is very unsatisfactory to me, as it bounces all of a sudden to drastically different settings.
basically, my analysis is that my controller is NOT receiving MIDI date from mainstage. in other words, mainstage knows what my controller is doing, but my controller doens't know what mainstage is doing.
let's say i turn the knob all the way to the right ... 127...and the virtual fader goes to the right like it's supposed to.
now...next...let's say i change to a different patch, where that same VIRTUAL fader is not at the max clockwise position..maybe it's only at 1pm. now when i turn the physical knob to the RIGHT, the midi data is still at 127 on the controller! it didn't "reset" to sync up with the new level (say 80 or so) setting on the new patch. so i can't increase that new setting of 80 by continuing to turn the knob to the right. i have to turn it all the way to zero,...and then continue PAST zero until the controller thinks that IT is at 0...at that point the controller and mainstage are in agreement, and things work fine....so bascially, the keyboard thinks the level is at max...but mainstage thinks the level is at 1pm.
i am using Logic 9, and i have a macbook pro 2.9 Ghz I7 with 8 gigs of memory and OS X 10.8.4

Hi Josh,
Thanks for taking the time to contact us here a Novation for technical support. Lets continue to correspond via email so we can get your issue resolved.
Thanks.
Mike Towns

Interesting and an imporatant issue at sales order schedule line.

hi all,
interesting and an imporatant issue at sales order schedule line.
i created a sales order with 10 qty.and the system proposed a two schedule lines.
let's say to order created date is 27.11.2008.and the requested delivery date is 27.11.2008.
but the stock is not available today then the system proposed two more schedule lines apart from the 27.11.2008.so now there are three schedule lines like below.
schedule line date                      Material availabilyt date   delivery date
27.10.2008 with zero quantity.
28.10.2008 with 5 qty.                28.10.2008                     29.10.2008
02.10.2008 with 5 qty.                02.10.2008                     03.10.2008
now the delivery and pgi already for the schedule line 28.10.2008.
then when i run the availability check on 01.11.2008 system is over writing the material vailability date as today at the scheduleline number two.
now i can able to view only two schedule lines only.
schedule line date                      Material availabilyt date   delivery date
28.10.2008 with 5 qty.                01.11.2008                     29.10.2008
02.10.2008 with 5 qty.                01.11.2008                     02.11.2008
now my concern when we reschedule the avalability check it should notchange the Material availability date of the schedule line which i already delivered.
Regards,
sheshukumar

can any one repsond for this.....

I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for

I downloaded CS6 and am having issues with my print driver. It is not compatible with the HP 2600n and have tried to download drivers given to me by adobe ( (Jupiter 3) but it is not working. after a few days. Its a temporary fix and is still looking for the HP driver when i boot up. It also will not save in any print or postscript format. Does anyone know how to fix?
Currently use a Mac with the latest Mavericks 10.9.4

Oh boy! Acting kind of weird seems to be an understatement, aquaequus!
What type of troubleshooting were we able to do with you? I want to make sure that we can get some sort of resolution for this problem.
It is quite possible the battery door may get your phone in working order again. I'm not sure if the store has it in stock, but it is available in our warehouse for $14.99 which can be ordered via customer service.
Tamara H.
Follow us on Twitter @VZWSupport

Report Builder - Last page issue and Report Footer issue

I am using ColdFusion 9 Report Builder, am new to this product and encountering 2 issues.
Issue 1 - I have a field that I would like to print on the last page of my report. How can I determine the last page? I initially tried using a calculated field set to the 'highest' calc.Page_Number. Then I could compare the current page to the last page in the 'Print When' property. But calc.Page_Number can not be used in a definition of a calculated field.
Issue 2 - Depending on the amount of report detail, sometimes my report footer prints alone, without a page header and page footer. The report includes this page in the total number of pages. For example, if it is a 2 page report, the page header on page 1 will display Page 1 of 2. Then the only data on Page 2 is the Report Footer. No page header or page footer prints.
Any assistance on these issues would be most appreciated. To date, using the Report Builder has not been easy.

To issue 1: The report contains a report band called report footer. thsi is always at the last page. The report footer band initially is collapsed, so you have to expand it by dragging the last band divider.
To issue 2: I guess this is a page break calculating error when detail data reaches really near the page footer area.
Try some experiments with different setting of the following properties/issues:
- in elements, e.g. calculating fields in the bands between report detail and page footer: In Properties / Print Control / Printing Options: Activate the option "Remove line when blank". This will remove the whole report band area if this field is blank. May save some empty space.
- try to remove unused empty space between detail rows.
- try to resize and reposition all detail fields so that they snap to the grid.
Best regards

WRT160NL and XBOX + AP issues

Similar Messages

Maybe you are looking for