WRT160NL will not configure in setup

Followed QUICK INSTALLATION GUIDE with 3 different computers, and this router cannot be found for set-up. Setup goes OK until powering up router, click "Next" to find it, and........... can't be found.

If your Internet Service Provider is Cable follow this link
If your Internet Service Provider is DSL follow this link

Similar Messages

WRT300N Router will not configure during setup

I have a WRT300N Router Version 1.1, when reinstalling this on my computer after a crash I cannot get the setup to complete. When the setup goes throught the config stage it gets to 99% and then stops and gives me an error message that it would not configure.
I have updated the firmware and this still will not get it to work. What can I do?

After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you have not done this since your last firmware upgrade, please do this now and see if it corrects your problem. If you saved a router configuration file, DO NOT use it.
To reset the router press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
If your Internet Service Providor is Cable follow this link
If your Internet Service Providor is DSL follow this link

Windows 8.1 will not download iTunes setup file

Windows 8.1 will not download iTunes setup file. It asks if I want to save the file. I click yes but it doesn't download. Tried numerous times on my new Toshiba Qosmio computer.

See the Further Information area of Troubleshooting issues with iTunes for Windows updates for download advice and direct links if required.
tt2

SQL Server 2012 Developer Edition will not install. Setup files don't even get copied completely. Win 8.1. ACT instance is loaded & can't be deleted. From log file: Error: Action "PreMsiTimingConfigAction" failed during execution.

SQL Server 2012 Developer Edition will not install. Setup files don't even get copied completely. Win 8.1. ACT instance is loaded & can't be deleted. From log file: Error: Action "PreMsiTimingConfigAction" failed during execution.

Hello,
I am glad it worked.
Thank you for visiting MSDN forums!
Regards,
Alberto Morillo
SQLCoffee.com

Will not let me setup email account. says problem with email try again later

Icloud will not let me setup email @iclould.com. Say has a problem try again later?

Here's the iPhone email setup assistant:
iPhone Email Setup

Yast will not configure Virtual Office

I have OES Linux and want to configure VO. From Yast clicking on the VO
icon displays an error message that VO will not install unless the rpms
for novell-oes-install and novell-selections are installed first. They
are installed! I have even uninstalled and reinstalled them but Yast
will not change its mind.
Q: How do I get VO to configure?
knuckles

knuckles,
It appears that in the past few days you have not received a response to your posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at http://support.novell.com in both the "free product support" and "paid product support" drop down boxes.
- You could also try posting your message again. Make sure it is posted in the correct newsgroup. (http://support.novell.com/forums)
If this is a reply to a duplicate posting, please ignore and accept our apologies and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/

PLEASE HELP ITUNES WILL NOT CONFIGURE

HI
my itunes will not load when i click it.
it comes up with a window which says-
+'itunes has encountered a problem and needs to close.+
++we are sorry for the inconvenience.'+ or sometimes pops up with 'itunes is unable to configure'+
can someone help me as i carnt upload new songs to my ipod
Arggg!
I have also tried to uninstall and reinstall this didnt make any difference.
thanks
Message was edited by: yo hoe
Message was edited by: yo hoe

iv been having some problems with my itunes to it cant find the .msi file or seomething
With that one, let's try the following procedure.
First, head into your Add/Remove programs and uninstall your QuickTime. If it goes, good. If it doesn't, we'll just attend to it when we attend to iTunes.
Next, download and install the Windows Installer CleanUp utility:
Description of the Windows Installer CleanUp Utility
Now launch Windows Installer CleanUp ("Start > All Programs > Windows Install Clean Up"), find any iTunes and/or QuickTime entries in the list of programs in CleanUp, select those entries, and click “remove”.
Next, we'll manually remove any leftover iTunes or QuickTime program files:
(1) Open Local Disk (C:) in Computer or whichever disk programs are installed on.
(2) Open the Program Files folder.
(3) Right-click the iTunes folder and select Delete and choose Yes when asked to confirm the deletion.
(4) Right-click the QuickTime folder and select Delete and choose Yes when asked to confirm the deletion. (Note: This folder may have already been deleted if QuickTime was successfully removed using Add/Remove Programs earlier.)
(5) Delete the QuickTime and QuicktimeVR files located in the C:\Windows\system32\ folder. Click Continue if Windows needs confirmation or permission to continue. (Note: These files may have already been deleted if QuickTime was successfully removed using Add/Remove Programs earlier.)
(6) Right-click on the Recycle Bin and on the shortcut menu, click Empty Recycle Bin.
(7) Restart your computer.
Now try another iTunes install. Does it go through properly now?

HT4623 Hi, I have taken over my daughters iphone 3gs and updated it and restored iphone but now it will not configure with my itunes or the original sim that was in it, saying "the activation server is temporarily unavailable. And will not connect to itun

Hi I have taken my daughters iphone and wiped it and resetted it but it will now not let me activate it via itunes and will not even go onto the home screen of the phone so i can go to settings etc and i do not know what to do to enable the phone to be activated

"We're Sorry, Activation Server Temporarily Unavailable, contact Customer Care?"
99.9% of the time, the cause of this issue is the fact the phone was jailbroken/hacked to unlock it for use on networks other than the network the phone was originally locked to. Apple maintains a database of officially unlocked iPhones, and when Apple's servers detect phones such as yours, activation stops & you get the message you got.
So, you need to get a sim card from the carrier the phone was originally locked to, or get it officially unlocked, if you want to activate it. Because it appears that it was not officially unlocked.

Itunes 10.7 setup stuck on 83.0 KB..will not complete the setup. What to do?

I have been trying to update my itunes to the new one since I got an iphone 5 today. But it will not finish the installation. It just stays at 99%. I have tried both Firefox and IE to update it.

Hello agardner37701,
I found some steps you can take when your iPhone is not recognized by iTunes when in Recovery Mode. I recommend reviewing the steps in the section titled "If the device is not recognized while in Recovery Mode" under step 5 in the following article:
iOS: Device not recognized in iTunes for Windows
http://support.apple.com/kb/TS1538
Thank you for using Apple Support Communities.
Best,
Sheila M.

WRE54G v1 will not configure

After trying all sorts of thing to get my 54G v1 RE configured, I came to this site. After going thru alot of ??'s, I found that I had tried them all except pushing the RESET and AUTO CONFIG at the same time, so tried that. It not only RESET the normal settings, it also CHANGED the MAC address. The orig MAC was 00-12-17-7b-be-f7, now it's 00-90-4c-60-04-00, how is this possible? I have tried to configure this v1 RE with the v1 software and I have never gotten past the SEARCH for a RE, it has never found it. I already have a v2 in use, (I'm trying to chain them) and if I use the v2 software, I can get all the way thru to the CONGRATS screen. Even tho' I get thru the set-up and the lights work like they should, I can not get past the v1 RE. I have tried to configure it to the router and also to the v2 RE, both come out the same. I have tried to configure to an unencrypted router, same results. I have also tried to go thru the web based set-up, but as I have never been able to ping the v1 RE, I can not use the web based. I have tried to leave the IP/SUBNET/GATEWAY address's in the default (reset) #'s and also trying #'s to correlate with my other RE and router, no difference. I think that covers everything, anybody have ideas? I wasn't confused until the MAC address got changed, now I don't know what to think. THANKS FOR YOUR TIME.

OK, I'm not sure if I missed understood previous instructions or what, but I now have this REv1 working. I tried doing what I do for my REv2 but over the wireless card and couldn't get the REv1 working correctly. I tried configuring it to the encrypted router that I'm on and also to the REv2 that I am using. I tried configuring it to a different router that wasn't encrypted, but still couldn't get on-line. I WAS able to get thru the set-up Wizard only once after doing a "factory" reset, and that with my v2 software. If I used the v1 software or tried to configure the REv1 with the v2 software without re-setting, the software NEVER found a WRE54G to configure. When I was able to get thru a config, the lights would work correctly, a blinking blue light for activity and a red for no signal, etc, but was never able to get anywhere. I was NEVER able to get to the web-based set-up page even trying the /backdoor.asp, it would never ping and the arp -a log would be all wrong, (the router MAC was all 0's). Since I had always figured it should be configured into/with the other RE and router, I kept trying to go that route. Well this is what I finally did to get the REv1 working. I set-up the equipment like this; router---->REv2------>me------->REv1 I left my wireless card's IP/SUBNET/Gateway etc address's as they are for normal use thru the REv2/router. *I did a "factory" reset on the REv1 *I started the v2 software and did the normal steps, *confirmed my wireless connection/address, ( NORMAL configuration) *entered my WEP 128bit password *when the REv1 was found, clicked yes *entered (admin) on the PASSWORD screen here is where things are different from a normal configuration *I set the IP address for the REv1 from 192.168.1.240 to 1 number less then the IP address of the REv2, (in my case it was 192.168.5.97). *I then set the GATEWAY from 192.168.1.1 to the REv2 IP address (192.168.5.98). I'm not positive on this order but, *When the screen came up that asked for the MAC address of the AP, (v1 only), I entered the MAC for the REv2. (this screen didn't always come up, but I entered that address every time). *finished running the set-up Wizard. I wasn't too hopeful after all the tries that I had done, but to my surprise, I was finally able to get on-line, ping the REv1, get to the web-based page and have the REv1 show up in the arp -a log. I had never tried to change the GATEWAY address to anything but the router's IP address and even tried leaving it at 192.168.1.1, but then it struck me that if I give the REv1 the MAC address for the REv2, I should set the GATEWAY to the REv2 IP address. So, I believe the main problem I had was the setting of the GATEWAY in the REv1 set-up. Even tho' I tried the auto-config to a "open" router, I just was not able to get "inside"/thru the REv1 until I set the GATEWAY to the REv2's IP address. this is my final set-up/use router------>REv2------>REv1------>me I still don't know why configuring it to a unencrypted router either with the AUTO CONFIG, the set-up WIZARD or why I couldn't access it through the web based even after running the v2 software Wizard with the "open" router, all I know is that what I did above worked, not only once, but twice (I did a Firmware update after the first and had to do it for a second time). Maybe this will help others kenya61

RE1000 - will not configure

zero stArS;
Linksys RE1000 Wireless-N Range Extender;
does not work;
just like other reviewerS.
brand new but; connects to router ,disconnects seconds later.
then connects then disconnects, etc.
zero stars!!

First of all please verify that you have got a 802.11n card in your computer. New generation devices speaks an entirely different language with 802.11g cards, so while those adapters can work with new generation devices, but they are not optimized to provide good performance. It is like having to translate from one language to another in real time when going from N to G.
Second, optimize the wireless settings on the router first.
1. Connect to your router's admin interface. Usually 192.168.1.1. The default user-name is blank; default password is "admin" (without the quotes).
2. Click on the Wireless tab and do the following changes.
For Channel Settings of 2.4 GHz you can make Channel Width to 20 MHz only and Channel to 6, 9, 11..
For Channel Settings of 5 GHz you can make Channel Width to 20 MHz only and Channel to 40 or 161...
3. Click on Save settings.
The Linksys Wireless Range Extender and wireless router or access point’s wireless settings should match in order for them to work properly. You must first identify the following wireless settings of your router:
• Wireless Network Name (SSID)
• Wireless Channel
• Wireless Security Mode (WPA/WPA2 Personal or WEP)
• Network Key or Passphrase
Here is the link for the configuration of the RE1000…
http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=206954591ff54e36884bb4636fcfd3d9_Manually_configur...
Lastly and most importantly, remember that in order to get the best performance from an RE1000 you need to place the extender in an area where you still have at least 50% signal strength to your router when you place it in the final location where the RE1000 will be used. To configure the RE1000 you will need to login to the UI after you have put the RE1000 in the final location to verify the signal strength below is a reminder about signal bars and what they mean as a reminder
For ALL configurations you should have between 2-3 bars of signal at the very least. If you have less we will need to move the RE1000 closer to the router. You can also check the status on the status page of the RE1000 as well. On the status page it measures both Signal Strength and Signal Quality. If either set of bars is red you must move the RE1000 closer to the Router.

Airport Extreme will not configure with Windows 7

Wanted to change password on air port express with windows 7 dell laptop. Airport utility could not find Extreme. Reset Extreme and found it but when I goto manual setup or any configuration setup it wants to run a Apple wireless device check and it fails with a error -4

Wanted to change password on air port express with windows 7 dell laptop. Airport utility could not find Extreme. Reset Extreme and found it but when I goto manual setup or any configuration setup it wants to run a Apple wireless device check and it fails with a error -4

C6250 on Win XP will not configure and install

I installed  HP Photosmart Full Feature Software and Drivers ver 10.0.1.
Doing a network install, the application sees the printer as a network device.
However, as it tries to configure and install, I get an ERROR, all it shows me is a large red "X" between the printer and the router, not other information.
I am running Win XP 32 bit on an HP (Compaq) 6910p Notebook.
I downloaded the  HP Home Network Diagnostic Utility and I was able to send a command to the printer to print a diagnositc page (from my notebook, wireless)
I have uninstalled and reinstalled 2 times. I tried downloading this patch :   Critical Update to Correct a PC to Printer Communication Issue but it faied. I tried downloading this update:  Critical Update to Enhance Reliability of Network and USB Connectivity and Improve System Responsive... but it told me I had no SW that required this update.
Any ideas ?

It sounds like you are unable to scan and that is why you need to install the printer. One problem I've seen is that a mutlifunction adapter for your product can be in the device manager prior to installation and that causes the device to fail to install. To open the device manager, go to the control panel and then click device manager (or hold the windows key and press the pause key, then click device manager). Once device manager is open, click the view menu and then click the "Show hidden devices" item. You should now see an item in the list in the main window for Multifunction adapters. Look for an entry under Multifunction adapters of "Photosmart C6250". If you find this entry, right-click on it and select "Uninstall" from the drop down menu. Now try to install the printer by inserting you CD and selecting "Add a device". The install should now succeed. If you didn't find an entry for your printer under multifunction adapters then your problem is elsewhere.
Mike
Say "Thanks" by clicking the Kudos Star in the post that helped you.
I am an HP employee.

Photoshop cs4 trial will not intall with setup exe

can anyone help i have downloaded the trial version of photoshop cs4 and extracted the files to an external hard drive but i cannot intall it on my computer when doulbe clicked on the setup exe file nothing happended it just opened it up and place a file on in the folder called ahmed or something like that can anyone help me with this problem i have plenty of disk space and plenty of ram. i am running windows xp professional and i have administrative privalages.

Bridge is not tied to any restrictions in terms of activation or requiring specific components to be in place, hence it almost always works. Do you correctly run the install with administrative privileges?
Mylenium

Oracle 10g will not configure metalink

I keep getting a wrong username/password error when trying to configure the metalink account in the oracle 10g enterprise manager, all entries are correct and the caps key is not on.

Do you have connection from your DB server to metalink? This could typically happend if you have no connection between your db server and the internet.
try
ping metalink.oracle.com
from your db server.
Regards
Laurent

WRT160NL will not configure in setup

Similar Messages

Maybe you are looking for