Wrt54g as a wireless card

I have a wrt54g running my wireless network, can i use another wrt54g as a wireless reciever to add another computer to my system?

No.. You just need to get an extra wireless adapter, it can PCI/USB wireless adapter for desktop computer user or wireless PCMCIA card/USB wireless adapter for laptop user (check first, most likely there is built-in wireless adapter on laptop).
picoHat
Home Network, Wireless Network and Computer Networking Made Easy

Similar Messages

Connectivity Issues WRT54G router and 2915ABG Dell wireless card

My wife and I both have Dell Inspiron 600m laptops with nearly the same setup: XP Pro, 2915ABG wireless cards, and the wireless connection is controlled through ProSet Wireless. We have Comcast and connect to a WRT54G wireless router. The router has WPA enabled, MAC address filtering, and the latest Firmware.
I have no trouble connecting to or remaining connected to the router. Her machine connects to the wireless, but randomly loses connection (sometimes it's connected for hours and other times it losses connection in the first five minutes). When I watch the ProSet wireless event viewer, it only says "link down."
To attempt to fix this problem, I have:
played with the router's settings including changing channels
updated her drivers
allowed windows to control the wireless card
reset the router
updated the router's firmware
None of these actions have fixed the problem. The only real differences between the two machines is that I did the following to mine:
My machine was the one that initially set up the wireless router
I used the Comcast install CD on my machine (then deleted all the *junk* that was installed by the CD).
I would like to avoid using the Comcast install CD on her machine because no one needs the extra junk they install. I did set up her machine according to the internet on how to set up Comcast without the CD.
I am trying to figure out if the problem is with the router or with her hardware. Thank you,
Michael

Try upgrading the firmware on the router.
For information on upgrading the firmware on the linksys routers :
http://linksysfirmwares.googlepages.com/upgradingfirmware
For information on wireless security :
http://linksysfirmwares.googlepages.com/wirelesssecurity
Keep the channel on 11 and than give it a try !
C | EH
linksyshelp.blogspot.com

Can WRT54G connect 2 XP laptops with different wireless cards, i.e. b and g,?

My WRT54G router works fine with a lenovo windows laptop (Intel wireless 3945ABG card) and my dell linux box but it is not accepting my old T40 laptop which has a dual-band wireless a/b card.   The WRT54G box indicates this router accepts both b and g wireless cards.
Question is can this router simultaneously hookup these 2 laptops  or do I have to resetup the router in order for it to work on the T40?
as it is now, the wireless network shows on my T40 and it appears to 'take' the access key i input but then the T40 just 'hangs' trying to get into that network.   I have set the encryption key on the router to WPA. and i want to keep this.

Make sure the computer that can't connect has DHCP enabled, Update the computer wireless card drivers, Check that the security you entered is correct.
GoodLuck
Matt

RE: Network Connect of a WMP100N Wireless card Thru a WRT54G Router

Well, I disabled the Zonealarm personal firewall. No change in connectivity. The card acquires the router, has super signal strength, and no internet. I've even tried re-doing the connection profile. I have noticed a minor difference in security settings. The router is configured WPA with PSK using TKIP + AES. The card gives me the option of either TKIP or AES (not the plus) Probably doesn't matter since the card only acquires the router when TKIP is chosen. I have also noticed when I tried using the rightclick repair option that windows lists encryption as disabled. If the card security settings match that of the router and access is established, isn't encryption enabled? Re-enabled the wired card and immediately established and internet connection. Am lost as to why I can't get internet thru the wireless card. There is an IP address and standard subnet mask. There just is a blank gateway, DNS and etc.

Well, I may have made a mistake. I spent some time on Live Chat with no real success. After all that, I decided to update firmware for the router. Here's where I may have goofed. Rather than use the old way to update, I used the linksys upgrade application. It did upgrade the router. Unfortunately, it seems to have corrupted my OS installation. I can't get XP (SP2) to properly shutdown. It goes partway thru the process, then I hear a click, the fans start whirring and it reboots. I end up having to push and hold the power button for shut off. Not a good solution. Any ideas? I am considering uninstalling the wireless card and doing a system restore pre-card. (BTW, the wireless card worked after the firmware update (although the connection does drop fairly often without any other 2.4 competing devices)

WRT54GS v7 loses wireless connectivity after 15 minutes or so

I just installed a WRT54GS v7 router to work with my cable modem. It has the latest firmware. The wireless connection seems to work for about 15 minutes or so at a time and then it stops working. I can't even get to 192.168.1.1. The only way to get it to work is unplug the router and plug it back in. Originally, I thought it was interference from my 2.8GHz cordless phone, so I unpluged it. But that still didn't fix the problem. What could be the problem? Thanks.

@mallinj
Hi,
Disconnect from Internet.
Uninstall from Your system audio drivers.
Resources:
Uninstalling Software in Windows 7
Uninstall or change a program in Windows 7
Restart Your system:
On boot press ' F8 ' and choose ' Safe mode '.
Go to Control Panel -> Devices Manager -> Network Cards
and find there Athero Wireless card. Click on it with right button of Your mouse and choose uninstall driver.
Restart Your system and this time start it in normally.
Install latest driver:
Atheros Wireless here (ver 8.0.0.238 for 32/64 bit Win7)
** Say thanks by clicking the "Thumb up" icon which is on the left. **
** Make it easier for other people to find solutions, by marking my answer with "Accept as Solution" if it solves your issue. **

WRT54GS - 7.0 Wireless signal disappears periodically

I have had my WRT54GS - 7.0 for about two months. Because of the way my apartment is set up, I am using a wireless card in my pc instead of a wired LAN connection from my cable modem. My ISP is fine; the computer wired to the router never experiences any difficulty.
My problem is that once in a while my wireless signal dips or disappears. My pc is only about 40 feet from the wireless router, and most of the time my signal is quite strong. I have software that allows me to see competing wireless networks and I know that I am not sharing a channel with anyone. It doesn't happen regularly; it will be fine for a week or even a month, then I'll have a horrendous couple of days where nothing I do can get it to connect. Sometimes it is two hours before the signal comes back. Cycling the power and resetting the router has no effect.
Should I buy a wireless repeater, or is there some other sinister agent at work besides cruddy signal transmission?
Any and all suggestions are welcome, and thanks to all who took time to read!
Message Edited by dgold on 04-11-200704:54 PM

dgold!
Make sure that there are no interferences between the two devices. Changing the channel would do as well, an if still it's the same. Set the "advance wireless settings" on the router [Beacon = 70; RTS = 2305; Fragmentation = 2306].

WRT54G in a wireless saturated neighborhood

I have a WRT54G that is having trouble staying connected after we moved to our new apartment. The neighborhood has tons of routers in the area (discovered by scanning with a software package recommended by a friend) and all channels are being used by other routers. It works fine during the day on weekdays but once the kids in the neighborhood start getting home from school and on the weekends I get disconnected frequently. Since it is pretty much always during peak hours I'm figuring my router is having trouble picking my data out of the air when everyone else has their signals on the same frequencies. It just "loses" the signal.
Is there any way I can change the settings to help the router stay connected? Also, how do you know the best way to aim the antennas for best signal?
Hardware involved:
WRT54G v2
Sony VAIO laptop about 1 year old
Sony VAIO laptop about 2 years old

I don't use any specific software to measure signal strength, just what came with the wireless card. Most of the wireless cards that I have seen come with the ability to display all the network router signals that they find. For each system, they list the SSID, wireless type (a,b,g), whether the system is open or encrypted, and how many "bars of signal strength" (usually 1 to 5) they are receiving. If this software did not come with your system, perhaps Sony (or whoever you got your wireless card from) has upgraded software available.
You have not mentioned yet the following critically important information:
1) What type of wireless cards are in your computers? (a, b, g)
2) How far away are the computers from the router?
3) How many walls and floors are you trying to go through? Are they concrete-rebar? Drywall?
4) If you position your wireless computers in the same room with your router, do you still get dropped connections?
Before you toss out your wireless G, there are a few other options:
1) make sure you have the latest software drivers for your wireless cards, and the latest firmware for your router.
2) If all your wireless devices are wireless g, set your router to "g only". If they are all wireless b, set your router to "b only".
3) radio waves propogate perpendicular to the antena. Imagine a straight line between your router and your wireless computer. Orient the antena perpendicular to this line.
4) Even more important than orienting the antena is to minimize the distance and the number of walls between the router and the wireless computers. Sometimes eliminating a wall is more important than getting the router a few feet closer. Also, try to move your router away from your other computer equipment.
When you position your router, imagine a straight line beween your router and your wireless computers, and try to position the router to minimize the amount of building materials along that line.
5) If placing your wireless computers in the same room with your router corrects all your problems, then the best solution would be to add a wireless access point to your system. This would need to be wired to your router. The main advantage of adding a wireless access point is that you can place it in the same room with your wireless computers. This will give you maximum signal strength.
6) The best channels to set your router to are usually 1, 6, or 11. But other channel may also work. Don't be afraid to experiment. Also, don't forget, the interference that you are experiencing may NOT be from your neighbor's wireless routers, it might be from their wireless phones! (i.e. Checking your neighbors wireless router channels only gives you a starting point.)
7) Make sure you are not interfering with your own signal. Any device that puts out radio signals, especially in the 2.4 GHz range, can potentially interfere with your router and cause line drops. Typical culprits are 2.4 GHz wireless phones. For more info on this topic, please see my previous post at:
http://forums.linksys.com/linksys/board/message?board.id=Wireless_Routers&message.id=9369&query.id=2...

Can I connect with built-in laptop wireless card?

Hi, I have a WRT54G set up and working fine on my main pc, connected to cable modem with a pc and laptop using linksys adapters. BUT I am trying to connect my third laptop using the internal wireless built in and was wondering how to connect this way. It was easy with the adapters because I used the linksys software that came with them. But with the built-in which is an Intel-PRO, it states the "wireless connection is not connected" and when I access the properties it tells me that I should configure with the software that came with the device. I'm running XP as the OS. I'm stumped. Any advice? Thanks.

In the non-working computer, temporarily turn off the software firewall, and see if this helps.
Also, what wireless card are you using? The Intel Pro Wireless 2200bg card is known to have connection problems that were fixed with the latest driver. If you have this card, go to the Intel web site and download and install the latest driver.

WRT54G V8 Dropping wireless connection

Hello,
I have an issue with my Lynksys WRT54G V8 (firmware upgraded to V8.00.2). No problem whatsoever with wired connection, however, it appears to drop my wireless connection every 10 or so minutes. I appear to be able to connect to my neighbors unsecured connection with no problem however.   The only way I can figure out to reconnect is to power the device off and on again. Disabling and enable the wireless adapter on my laptop does nothing.
Here is what I have tried:
I have moved the device to be closer to my laptop (it is now approximately 6 inches away).
I have changed the channel to be 11 instead of default 6.
I have changed client lease time from 0 to 999
I have upgraded the firmware to 8.00.2
Verified that my SSID is unique
This is the 3rd wireless setup I have done (separate places, 1 office and 1 in my home and this one in my vacation home). This is the first time I have had any issues. It is the same laptop, I have the same model of cordless phone in my home as the vacation home.   The only thing I am not sure of is the firmware level of the other two devices. They are the same model.
Any suggestions before I return this device and buy another model?
Thank you

After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you have not done this since the last firmware upgrade, please do this now, and see if it corrects your problem. If you saved a router configuration file, DO NOT use it.    If the above does not fix your problem, then read on:
There are many causes for poor wireless connections, and many solutions:
Set "SSID Broadcast" to "enabled". This will help your computer find and lock on to your router's signal.
Poor wireless connections are often caused by radio interference from other 2.4 GHz devices. This includes wireless phones, wireless baby monitors, microwave ovens, wireless mice and keyboards, wireless speakers, and your neighbor's wireless network. In rare cases, Bluetooth devices can interfere. Even some 5+ GHz phones also use the 2.4 Ghz band. Unplug these devices, and see if that corrects your problem.
In your router, try a different channel. There are 11 channels in the 2.4 GHz band. Usually channel 1, 6, or 11 works best. Check out your neighbors, and see what channel they are using. Because the channels overlap one another, try to stay at least +5 or -5 channels from your strongest neighbors. For example, if you have a strong neighbor on channel 9, try any channel 1 through 4.
Also, try to locate the router about 4 to 6 feet above the floor, in an open area. Do not locate it behind your monitor or near other computer equipment or speakers. The antenna should be vertical.
Also, in the computer, go to your wireless software, and go to "Preferred Networks" (sometimes called "Profiles" ). There are probably a few networks listed. Delete any network named "linksys". Also delete any network that you do not recognize, or that you no longer use. If your current network is not listed, enter its info (SSID, encryption (if any), and key (if any) ). Then select your current network and make it your default network, and set it to automatic login. You may need to go to "settings" to do this, or you may need to right click on your network and select "Properties" or "settings".
Also, you did not mention what type of encryption you were using. If you are using WPA2, or "WPA with AES" (= WPA2 ), then note that Windows XP requires a patch to run WPA2. Go to Microsoft Knowledge base, article ID=917021 and it will direct you to the patch.
Sadly, the patch is not part of the automatic Windows XP updates, so lots of people are missing the patch.
If the above does not fix your problem, download and install the latest driver for your wireless card.
If you continue to have trouble, try the following:
For wireless g routers, try setting the "Transmission Rate" to 54 Mbps. For wireless n routers, try setting the "n Transmission Rate" to 162 Mbps, and the (wireless g) "Transmission Rate" to 54 Mbps.
If you still have trouble, download and re-install the latest firmware for your router. After a firmware upgrade, you must reset the router to factory defaults, then setup the router again from scratch. If you saved a router configuration file, DO NOT use it.
Hope this helps.

Wireless Card Auto-Connect

I have a question about the auto-connect feature for the wireless adaptor (built-in) in my laptop (HP Pavillion dv600t). When I start/boot the system the wireless card finds the router (Linksys WRT54GS) and automatically connects to it no problem. However if I shut off the wireless link via the switch on the laptop and then turn it on again later, (such as when I want to connect via the network card and cable to port 1 for better performance) it will not re-connect on it's own. The network/router is visible on the available network list and it is set to auto but even when I select it and hit "connect" it never does. I need to use the windows "repair link" feature to correct it, after which it works fine again. (unless someone turns the switch off again). Is this normal or is there some setting I'm missing that I need to tweak?
Thank you...

well...there is no setting on the router as such for the kind of issue you are facing with....it could be possibly the adapter itself...try updating the drivers for it...

Wireless-Card doesn't not work with WPA/WPA2 but with WEP [Solved]

Hello I have a MacBook (late 2007) with a wireless-card from Broadcam, the card works with WEP and the classic configuration over rc.conf very well. But I can't get the card running with WPA and the net network-profiles.
Here is the link to the driver - http://www.broadcom.com/support/802.11/linux_sta.php
eth2 = wireless-card
eth1 = firewireanything
eth0 = wired-card
rc.conf
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Europe/Berlin"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
#MODULES=(sky2 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="macbook"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="eth0 192.168.1.220 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(!eth0 !eth1 eth2)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
NETWORKS=(wireless)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network net-profiles netfs alsa crond portmap fam hal)
/etc/network.d/wireless
CONNECTION="wireless"
INTERFACE=eth2
HOSTNAME=macbook
IP="static"
IFOPTS="192.168.1.225 netmask 255.255.255.0 broadcast 192.168.1.255"
GATEWAY=192.168.1.1
DNS1=192.168.1.1
# Wireless Settings (optional)
ESSID=3Com
#KEY=
IWOPTS="mode managed essid $ESSID channel 11"
#WIFI_INTERFACE=wlan0 # use this if you have a special wireless interface
# that is linked to the real $INTERFACE
#WIFI_WAIT=5 # seconds to wait for the wireless card to
# associate before bringing the interface up
USEWPA="yes" # start wpa_supplicant with the profile
WPAOPTS="" # use "" for normal operation or specify additional
# options (eg, "-D ipw")
# see /etc/wpa_supplicant.conf for configuration
Can I set here the WPA/WPA2-Key also? Why here ESSID? Do I need still a configuration in wpa_supplicant.conf?
Thats very confusing and not explained.
WPAOPTS? Do I need to add something like "-D wext"?
/etc/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel
network={
key_mgmt=NONE
priority=-9999999
network={
ssid="3Com"
proto=WPA
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="topsecret"
priority=5
# WPA2
# proto=WPA RSN
I need help. Please
Last edited by hoschi (2009-01-04 20:21:58)

fwojciec wrote:If this info is not in the wiki it might be worth it to add it -- it's all detailed in /etc/network.d/examples/complete.example though.
Thats the reason why I was so confused.
My new and well working configuration:
# /etc/rc.conf - Main Configuration for Arch Linux
# LOCALIZATION
# LOCALE: available languages can be listed with the 'locale -a' command
# HARDWARECLOCK: set to "UTC" or "localtime"
# USEDIRECTISA: use direct I/O requests instead of /dev/rtc for hwclock
# TIMEZONE: timezones are found in /usr/share/zoneinfo
# KEYMAP: keymaps are found in /usr/share/kbd/keymaps
# CONSOLEFONT: found in /usr/share/kbd/consolefonts (only needed for non-US)
# CONSOLEMAP: found in /usr/share/kbd/consoletrans
# USECOLOR: use ANSI color sequences in startup messages
LOCALE="en_US.utf8"
HARDWARECLOCK="UTC"
USEDIRECTISA="no"
TIMEZONE="Europe/Berlin"
KEYMAP="us"
CONSOLEFONT=
CONSOLEMAP=
USECOLOR="yes"
# HARDWARE
# MOD_AUTOLOAD: Allow autoloading of modules at boot and when needed
# MOD_BLACKLIST: Prevent udev from loading these modules
# MODULES: Modules to load at boot-up. Prefix with a ! to blacklist.
# NOTE: Use of 'MOD_BLACKLIST' is deprecated. Please use ! in the MODULES array.
MOD_AUTOLOAD="yes"
#MOD_BLACKLIST=() #deprecated
#MODULES=(sky2 snd-mixer-oss snd-pcm-oss snd-hwdep snd-page-alloc snd-pcm snd-timer snd snd-hda-intel soundcore)
# Scan for LVM volume groups at startup, required if you use LVM
USELVM="no"
# NETWORKING
# HOSTNAME: Hostname of machine. Should also be put in /etc/hosts
HOSTNAME="macbook"
# Use 'ifconfig -a' or 'ls /sys/class/net/' to see all available interfaces.
# Interfaces to start at boot-up (in this order)
# Declare each interface then list in INTERFACES
# - prefix an entry in INTERFACES with a ! to disable it
# - no hyphens in your interface names - Bash doesn't like it
# DHCP: Set your interface to "dhcp" (eth0="dhcp")
# Wireless: See network profiles below
eth0="eth0 192.168.1.220 netmask 255.255.255.0 broadcast 192.168.1.255"
INTERFACES=(!eth0 !eth1 !eth2)
# Routes to start at boot-up (in this order)
# Declare each route then list in ROUTES
# - prefix an entry in ROUTES with a ! to disable it
gateway="default gw 192.168.1.1"
ROUTES=(!gateway)
# Enable these network profiles at boot-up. These are only useful
# if you happen to need multiple network configurations (ie, laptop users)
# - set to 'menu' to present a menu during boot-up (dialog package required)
# - prefix an entry with a ! to disable it
# Network profiles are found in /etc/network.d
# This now requires the netcfg package
NETWORKS=(3com)
# DAEMONS
# Daemons to start at boot-up (in this order)
# - prefix a daemon with a ! to disable it
# - prefix a daemon with a @ to start it up in the background
DAEMONS=(syslog-ng network net-profiles netfs alsa crond portmap fam hal)
CONNECTION="wireless"
DESCRIPTION="Very verbose complete wireless example"
INTERFACE=eth2
HOSTNAME=macbook
# Interface Settings (use IP="dhcp" for DHCP)
IP="static"
IFOPTS="192.168.1.225 netmask 255.255.255.0 broadcast 192.168.1.255"
GATEWAY=192.168.1.1
# DNS Settings (optional)
DOMAIN=localdomain
DNS1=192.168.1.1
DNS2=
SEARCH=
# Standard Wireless Settings
ESSID=3Com
SECURITY=wpa-config # One of wep, wpa, wpa-config, none
KEY=""
# Scans to see if network is available before connecting (reccomended)
SCAN="YES"
# Time to wait to connect to a network. Default 15.
TIMEOUT=10
# Pass *custom* options to iwconfig. Usually not needed (optional)
IWOPTS="mode managed essid $ESSID channel 6 key restricted $KEY"
# Any extra arguments for wpa_supplicant
WPA_OPTS=
# For SECURITY='wpa-config' only - filename of a wpa-supplicant config
WPA_CONF=/etc/wpa_supplicant.conf
# This is a network block that connects to any unsecured access point.
# We give it a low priority so any defined blocks are preferred.
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=wheel
network={
key_mgmt=NONE
priority=-9999999
network={
ssid="Linksys"
proto=WPA RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="areulookingatmybreasts"
priority=5
network={
ssid="3Com"
proto=WPA
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="nomam"
priority=5
# WPA2
# proto=WPA RSN
There are also profiles for the Linksys-Router and for wired cable.
Thanks for the help!
Last edited by hoschi (2009-01-04 20:21:23)

PCI-e wireless card causes lock ups Z87 MPower MAX

I've already asked this question once, but was part of an epic essay that I've decided to break down into smaller more manageable chunks (as unsurprisingly that one got no replies).
I've got an ASUS PCE-A66 wireless ac pci-e card. Had absolutely no issues with it in my old Z77 board, but I seem to be having a lot of issues with it in my new Z87 MPower MAX. System was locking up like mad when I was trying to install the drivers at first. Had to rip out the WiFi/Bluetooth/WiDi module to get the drivers installed but the system randomly hangs on boot up? Don't get the issues with the card unplugged and don't always get it with it plugged in, but there seems to be some form of conflict with it that I can't resolve. Has anyone else had any such issues with any PCI-e add in cards on this motherboard?
Specs are:
i7 4770k
MSI MPower MAX using .128 bios (will try the .131 later)
2x4GB Corsair Dominator Platinum 2400
Coolermaster Silent Pro Hybrid 1050w
EVGA NVidia GTX 780 SC ACX
Windows 8 Pro 64bit

Yes, old system was Win8 Pro 64 bit too and the drivers are Windows 8 certified. As I say though, I had no issues with it on the old build? Even got a replacement sent out by Amazon in case the card itself was damaged Did initially try to do a warm update of the hardware into the same OS installation but didn't play well so did a full re-install in the end. Tried standard and UEFI installs (just in case) and after a problem with my OCZ Vector 2 not being recognised I bought a new Samsung 840 Pro so was a virgin SSD installed on to as well.
I'll raise it directly with MSI but just wanted to know if anyone else had experienced anything similar with any wireless cards in this mobo.
Cheers for the reply though

Wireless card BCM4313 no connection at boot

Hi,
I have an HP Pavilion dv6 with a Broadcom BCM4313 wireless card. I use NETCFG and before the last kernel upgrade I was able to connect to my home wireless connection at boot without troubles. Now I have to do it manually and I need to try 2 or 3 times to see my connection active.
lspci -vnn
02:00.0 Network controller [0280]: Broadcom Corporation BCM4313 802.11b/g/n Wireless LAN Controller [14e4:4727] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:1483]
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at c3400000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: brcmsmac
Kernel modules: bcma, wl, brcmsmac
lsmod
Module Size Used by
cpufreq_stats 3890 0
radeon 992718 0
ttm 54360 1 radeon
ipv6 290407 22
cpufreq_ondemand 6132 4
uvcvideo 64931 0
videodev 78006 1 uvcvideo
media 10437 2 uvcvideo,videodev
usbhid 35256 0
hid 81635 1 usbhid
v4l2_compat_ioctl32 8292 1 videodev
snd_hda_codec_hdmi 22092 1
joydev 9895 0
snd_hda_codec_idt 55175 1
i915 707307 7
snd_hda_intel 22122 0
snd_hda_codec 77927 3 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel
drm_kms_helper 25409 2 radeon,i915
lib80211_crypt_tkip 8506 0
drm 183380 5 radeon,ttm,i915,drm_kms_helper
snd_hwdep 6325 1 snd_hda_codec
snd_pcm 73856 3 snd_hda_codec_hdmi,snd_hda_intel,snd_hda_codec
snd_timer 19416 1 snd_pcm
r8169 42643 0
lib80211 4158 1 lib80211_crypt_tkip
snd 57786 7 snd_hda_codec_hdmi,snd_hda_codec_idt,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
sg 25557 0
hp_accel 13864 0
lis3lv02d 10508 1 hp_accel
i2c_i801 8187 0
serio_raw 4294 0
iTCO_wdt 12717 0
hp_wmi 7738 0
intel_agp 10904 1 i915
arc4 1410 2
btusb 11577 0
evdev 9530 9
bluetooth 138465 1 btusb
soundcore 6146 1 snd
bcma 13762 0
i2c_algo_bit 5199 2 radeon,i915
sparse_keymap 3088 1 hp_wmi
mei 31249 0
i2c_core 20133 7 radeon,videodev,i915,drm_kms_helper,drm,i2c_i801,i2c_algo_bit
iTCO_vendor_support 1929 1 iTCO_wdt
pcspkr 1819 0
snd_page_alloc 7121 2 snd_hda_intel,snd_pcm
intel_ips 11213 0
psmouse 55224 0
intel_gtt 14423 3 i915,intel_agp
mii 3995 1 r8169
input_polldev 2882 1 lis3lv02d
battery 10905 0
wmi 8411 1 hp_wmi
ac 3265 0
button 4470 1 i915
brcmsmac 594624 0
thermal 7863 0
video 11228 1 i915
brcmutil 6563 1 brcmsmac
mac80211 215605 1 brcmsmac
cfg80211 160516 2 brcmsmac,mac80211
rfkill 15402 3 hp_wmi,bluetooth,cfg80211
crc_ccitt 1331 1 brcmsmac
acpi_cpufreq 5877 1
freq_table 2451 3 cpufreq_stats,cpufreq_ondemand,acpi_cpufreq
processor 24256 1 acpi_cpufreq
mperf 1275 1 acpi_cpufreq
ext4 369556 2
mbcache 5817 1 ext4
jbd2 71074 1 ext4
crc16 1297 2 bluetooth,ext4
sr_mod 14951 0
sd_mod 28307 4
cdrom 36329 1 sr_mod
ahci 20865 3
libahci 18885 1 ahci
libata 173297 2 ahci,libahci
ehci_hcd 39511 0
scsi_mod 131482 4 sg,sr_mod,sd_mod,libata
usbcore 142544 5 uvcvideo,usbhid,btusb,ehci_hcd
dmesg | grep wlan0
[ 11.715805] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 13.791409] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 16.885059] wlan0: authenticate with 50:67:f0:ab:4f:d4 (try 1)
[ 16.886567] wlan0: authenticated
[ 16.890100] wlan0: associate with 50:67:f0:ab:4f:d4 (try 1)
[ 16.892793] wlan0: RX AssocResp from 50:67:f0:ab:4f:d4 (capab=0x471 status=0 aid=1)
[ 16.892798] wlan0: associated
[ 16.894146] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 26.697130] wlan0: deauthenticating from 50:67:f0:ab:4f:d4 by local choice (reason=3)
[ 87.612906] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 89.754106] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 92.849882] wlan0: authenticate with 50:67:f0:ab:4f:d4 (try 1)
[ 92.851661] wlan0: authenticated
[ 92.851823] wlan0: associate with 50:67:f0:ab:4f:d4 (try 1)
[ 92.854142] wlan0: RX AssocResp from 50:67:f0:ab:4f:d4 (capab=0x471 status=0 aid=1)
[ 92.854150] wlan0: associated
[ 92.855920] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 103.719958] wlan0: no IPv6 routers present
[ 105.980215] wlan0: deauthenticating from 50:67:f0:ab:4f:d4 by local choice (reason=3)
[ 120.237260] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 122.316759] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 125.422195] wlan0: authenticate with 50:67:f0:ab:4f:d4 (try 1)
[ 125.423760] wlan0: authenticated
[ 125.423960] wlan0: associate with 50:67:f0:ab:4f:d4 (try 1)
[ 125.426083] wlan0: RX AssocResp from 50:67:f0:ab:4f:d4 (capab=0x471 status=0 aid=1)
[ 125.426090] wlan0: associated
[ 125.428085] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 136.398877] wlan0: no IPv6 routers present
You could see that first I get the connection and then I lost it... for 2 or 3 times, then I could connect without problems.
ifconfig
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:338 errors:0 dropped:0 overruns:0 frame:0
TX packets:338 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:27772 (27.1 Kb) TX bytes:27772 (27.1 Kb)
wlan0 Link encap:Ethernet HWaddr E0:2A:82:A2:B5:88
inet addr:192.168.1.33 Bcast:192.168.1.255 Mask:255.255.255.0
inet6 addr: fe80::e22a:82ff:fea2:b588/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:12484 errors:0 dropped:0 overruns:0 frame:0
TX packets:9606 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:13841736 (13.2 Mb) TX bytes:1241490 (1.1 Mb)
iwconfig
wlan0 IEEE 802.11bgn ESSID:"WLAN_A9"
Mode:Managed Frequency:2.452 GHz Access Point: 50:67:F0:AB:4F:D4
Bit Rate=54 Mb/s Tx-Power=19 dBm
Retry long limit:7 RTS thr:off Fragment thr:off
Power Management:off
Link Quality=40/70 Signal level=-70 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:82 Missed beacon:0
my wirelessCasa netcfg profile
CONNECTION='wireless'
DESCRIPTION='A simple WEP encrypted wireless connection'
INTERFACE='wlan0'
SECURITY='wep'
ESSID='WLAN_A9'
KEY='s:mykey'
IP='dhcp'
POST_UP="notify-send -u critical -i /usr/share/icons/Faenza/status/48/connect_established.png -t 15000 'Connected to WLAN_A9'"
POST_DOWN="notify-send -u critical -i /usr/share/icons/Faenza/status/48/gnome-netstatus-disconn.png -t 15000 'Connection lost'"
# Uncomment this if your ssid is hidden
#HIDDEN=yes
rc.conf
NETWORKS=(wirelessCasa)
DAEMONS=(syslog-ng dbus net-profiles net-auto-wired !network !netfs crond laptop-mode alsa slim @acpid @cups)
When I execute netcfg for the first time (after boot) I see:
#NETCFG_DEBUG=yes netcfg wirelessCasa
DEBUG: Loading profile wirelessCasa
DEBUG: Configuring interface wlan0
:: wirelessCasa up [BUSY] DEBUG: status reported to profile_up as:
DEBUG: Loading profile wirelessCasa
DEBUG: Configuring interface wlan0
DEBUG: wireless_up stop_wpa wlan0
DEBUG: wireless_up start_wpa wlan0 /run/network//wpa.wlan0/wpa.conf nl80211,wext
DEBUG: wireless_up stop_wpa wlan0
DEBUG: wireless_up Configuration generated at /run/network//wpa.wlan0/wpa.conf
DEBUG: wireless_up ifup
DEBUG: wireless_up start_wpa wlan0 /run/network//wpa.wlan0/wpa.conf nl80211,wext
DEBUG: wireless_up wpa_check
DEBUG: wpa_cli -p /run/wpa_supplicant -i wlan0 status
DEBUG: Loading profile wirelessCasa
DEBUG: Configuring interface wlan0
DEBUG: ethernet_iproute_up ifup
DEBUG: ethernet_up dhcpcd -qL -t 10 wlan0
DEBUG:
> DHCP IP lease attempt failed.
DEBUG: Loading profile wirelessCasa
DEBUG: Configuring interface wlan0
DEBUG: Loading profile wirelessCasa
DEBUG: Configuring interface wlan0
DEBUG: ethernet_down if_down
DEBUG: wireless_down stop_wpa wlan0
DEBUG: profile_up connect failed
[FAIL]
And the second one:
#NETCFG_DEBUG=yes netcfg wirelessCasa
DEBUG: Loading profile wirelessCasa
DEBUG: Configuring interface wlan0
:: wirelessCasa up [BUSY] DEBUG: status reported to profile_up as:
DEBUG: Loading profile wirelessCasa
DEBUG: Configuring interface wlan0
DEBUG: wireless_up stop_wpa wlan0
DEBUG: wireless_up start_wpa wlan0 /run/network//wpa.wlan0/wpa.conf nl80211,wext
DEBUG: wireless_up stop_wpa wlan0
DEBUG: wireless_up Configuration generated at /run/network//wpa.wlan0/wpa.conf
DEBUG: wireless_up ifup
DEBUG: wireless_up start_wpa wlan0 /run/network//wpa.wlan0/wpa.conf nl80211,wext
DEBUG: wireless_up wpa_check
DEBUG: wpa_cli -p /run/wpa_supplicant -i wlan0 status
DEBUG: Loading profile wirelessCasa
DEBUG: Configuring interface wlan0
DEBUG: ethernet_iproute_up ifup
DEBUG: ethernet_up dhcpcd -qL -t 10 wlan0
DEBUG:
DEBUG: ethernet_iproute_up hostname archlap
[DONE]
I've tried to use the wl driver but it doesn't seems to work properly.
Could anyone help me please?
Thank you,
enrico

litemotiv wrote:
Hmm it seems your card now takes longer to connect, the 'deauthenticating by local choice' often means that the default timeout is reached and netcfg disconnects. You can try adding a specific timeout parameter to your netcfg profile:
TIMEOUT=60
That doesn't explain why it takes longer to connect than before, but at least you should be able to connect in 1 try again.
Hi,
thank you for your time!
I'v tried adding the timeout line to my profile but it doesn't change nothing
I could connect at 3rd try.
Any other idea?

Startup gets 'Network cable unplugged' on mini-PCI wireless card

I recently installed a Netgear DG834GT wireless router and now have an intermittent problem connecting my Tecra 9100 to it. If the 9100 has been shutdown for a while (like overnight), when I restart I always get 'Network cable unplugged' for the wireless connection. Rebooting a number of times (anything from 3 upwards) I eventually get connected to the router and all then works fine for hours. Even a quick restart at this point (i.e. once the wireless card has connected) does not cause a problem but as soon as I leave the machine shutdown for a length of time it fails again at reboot.
There are no errors in the Event log.
I am using the built in mini-PCI wireless card and have already upgraded to the latest driver.
Any ideas gratefully recieved, at the moment each morning is a 20-30 minute frustration of rebooting trying to get my connection working.
(Running Win2K Professional)

Checking other boards for help (Netgear etc.) it seems that the 'Network cable unplugged' is a common message when wireless connectivity is failing. However, to prove the point, I have disabled the other LAN card (for which I was also getting 'network cable unplugged' but as expected since it was). I still get the same issue with the wireless card, although now the reboots are slightly more predictable - it normally seems to succeed on the third reboot. I guess disabling the other card has changed the startup timing slightly and in that way made things slightly better.
Again, any other suggestions gratefully received. As this seems to be a timing issue at startup, I am suspicious that one of the other things that runs at that time is causing the problem.

Startup gets 'Network cable unplugged' on mini-PCI wireless card (again)

Reposting as previous topic has been locked although has not been resolved. Original post below, please see previous post for more details
I recently installed a Netgear DG834GT wireless router and now have an intermittent problem connecting my Tecra 9100 to it. If the 9100 has been shutdown for a while (like overnight), when I restart I always get 'Network cable unplugged' for the wireless connection. Rebooting a number of times (anything from 3 upwards) I eventually get connected to the router and all then works fine for hours. Even a quick restart at this point (i.e. once the wireless card has connected) does not cause a problem but as soon as I leave the machine shutdown for a length of time it fails again at reboot.
There are no errors in the Event log.
I am using the built in mini-PCI wireless card and have already upgraded to the latest driver.
Any ideas gratefully recieved, at the moment each morning is a 20-30 minute frustration of rebooting trying to get my connection working.
(Running Win2K Professional)

More info : I have found that this is time related rather than related to the number of reboots. It always fails on the first reboot after being shut down for a period of time. At this point, however long I wait the connection never comes up. However, if I wait a few minutes and then reboot, the second reboot will always successfully establish the connection.
On this basis, the problem has become slightly less annoying as I have a workaround - boot once, wait a few minutes and reboot. That being said, any information on how I can isolate this further (e.g. tracing what is running at startup) would be gratefully recieved.

Wrt54g as a wireless card

Similar Messages

Maybe you are looking for