WRT54G version 5 and Xbox 360 Wireless Controller

Hello,
I just upgraded to the latest firmware since my Xbox 360 Wireless adapter can't connect to my router. I still have the same problem and can't figure it out. I read some of the other posts, and opened up the correct ports in my router 88 & 3074. I even disabled wireless security and I still can't connect.
My wireless adapter is a solid red. I can connect just fine with a wired network cable. Does anyone have any suggestions for me to try?
It's a brand new Xbox too and there shouldn't be any problems with it.

Make sure the wireless settings are configured correctly. Also check with the adapter.

Similar Messages

Wrt54g and xbox 360 wireless gaming adapter

First post here and I have a problem. The WRT54G has wirlelss disabled. It is connected to a WAP11B wireless access point which is connected in 802.11b mode to a laptop, Wii, xbox 360, iPhone. The router is connected to a dsl modem. Three wired ethernet computers are connected. And I am running WEP with 128, and I changed the SSID to something other than linksys.
I'd like to change to use the WRT54G as a wireless enabled connection. Then remove the WAP11B, and put a pcmcia 802.11g card in the laptop and connect the xbox360 with a microsoft xbox 360 wireless gaming adapter which should connect at 802.11g.
The problem is the xbox 360 displays a message that there are duplicate networks using my SSID. Is there someway to upgrade to 802.11g without getting that error message on the xbox 360? Let me know if there are any questions I can answer in order to more clearly explain the problem.
Thank you,
Jordan
Solved!
Go to Solution.

Did you try to change the SSID...If not change the Network SSID and try...

[SOLVED] Xbox 360 Wireless Controller, how to make it work?

How can I get this to work under Arch? the controller gets detected at /dev/input/js0 and I if cat the file I get a bunch of symbols (which I read that means it works).
However, I can make it work with anything, am I missing something?
It even gets detected as: Bus 004 Device 003: ID 045e:0719 Microsoft Corp. Xbox 360 Wireless Adapter
The light on the controller keeps blinking but thats normal also.
If anyone can help out with this I would really appreciate it.
thanks for the help
Last edited by 655321 (2013-01-14 20:14:29)

Already read that but didn't help. However I found the problem. Controller wouldn't sync with the wireless receiver. I ended up using xboxdrv userspace driver and after sync it worked like a charm, even the xbox light stops blinking and stays fixed on the player 1
thanks for the help

TC new firmware and xbox 360 wireless adapter

So there is a new firmware for TC...it is ver 7.3.1. Any with the new firmware has tested the connectivity of TC wth the xbox 360 wireless adapter?? I don't have access to it now so I am hoping someone of you have tested and to share the success story??

**** IT!! I just tested the connection...no luck! When the **** is Apple going to fix this problem?!!!! I now regret getting rid of my AEBS for TC!!!!!!

WRT54GX4 Wireless Router and Xbox 360 Wireless Networking Adapter

I just got an Xbox 360 with a Wireless Networking Adapter. The adapter will recognize the network, but won't connect to it. Even if I remove the security, the Xbox 360 won't connect. Is there something else via the router I'm supposed to be doing? I called Microsoft and they said to open the port settings, but I don't know if that's really the issue and I don't know how to do that if I need to.
The ports they gave me were:
TCP 80
UDP 88
UDP 3074
TCP 3074
UDP 53
TCP 53
Thanks for any help if you can.

Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave username blank & in password use admin in lower case...
Click on "Applications and Gaming" tab and then click on "Port Range Forwarding" subtab...
1) On the first line in Application box type in ABC, in the start box type in 88 and End box type in 88, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
2) On the second line in Application box type in PQR, in the start box type in 3074 and End box type in 3074, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box...
3) On the third line in Application box type in XYZ, in the start box type in 53 and End box type in 53, leave the protocol as both and under ip address type in 192.168.1.20 and check the enable box and click on Save Settings...
3) Once you return to the set up page click on the Security tab and uncheck Block Anonymous Internet Requests and click on Save Settings...
4) Click on set-up and change the MTU Size to 1452 and click Save Settings...
5) Goto the XBox Network Settings and IP Address Settings and select manual IP Settings and assign the following on your Xbox
IP Address :- 192.168.1.20, Subnet Mask :- 255.255.255.0, Default Gateway :- 192.168.1.1...
6) Also assign the DNS Addresses on the Xbox
Primary dns :- 4.2.2.2...Secondary dns :- 192.168.1.1
7) Turn off your modem, router, and Xbox...Wait for a minute...
8) Plug the modem power first, wait for another minute and plug the router power cable, wait another minute and turn on the Xbox and test it...it will connect...

Xbox 360 Wired Controller is not working with Windows 7.

Not to long ago I was playing Halo 2 PC using my wired Xbox 360 Controller. All of a sudden my computer (which uses Windows 7) decides not to recognize it. Every time I plug in the controller in now it comes up as "Unknown Device". I have not changed anything,
I mean anything. Yes I have tried all methods of fixing the problem but they do not work. If someone knows a sure fine way to get the controller working again it would be much appreciated.

I 'm using a wired Gamestop Xbox 360 controller and I got mine to work using these steps. Good luck.
If you already have the software installed, go to programs and features and uninstall Microsoft XBOX 360 Accessories 1.2.
1) Download the drivers from
http://www.microsoft.com/hardware/download/download.aspx?category=gaming
2) Choose Gaming >
Xbox 360 Controller for Windows > Windows 7 64 bit > English.Don’t run the drivers.
Save them to a folder. (Or Xbox 360 Wireless Controller for Windows depending on your controller)
3) Right click the
Xbox360_64Eng file in the folder you downloaded to and click "create shortcut"
4) Right click the shortcut you created.
Select properties.
5) On the compatibility tab in properties, click "Run this program in compatibility mode"
ChooseWindows Server 2008 Service Pack 1 as the compatibility mode. Apply setting and click ok.
6) Right Click on the shortcut and select "Run as administrator"
7) With your controller plugged in go to
Device Manager. You should see Microsoft Common Controller for Windows Class. It located under Mice and other pointing if you do, you have arrived. If you don't, try this.
Continue only if you don’t see Microsoft Common Controller for Windows Class in Device Manager
8) Right click the unknown device that shows a problem.
9) Update Driver Software > Browse My computer for Driver Software > Let Me Pick from a List of Drivers
10) Choose Microsoft Common Controller for Windows Class > XBOX 360 Wireless Receiver for Windows
Ignore the warning.
Should work now.

Does the Xbox 360 wireless adapter even work with the WRT54G wireless router?!!? If so, how???

I just bought a WRT54G wireless router (Ver 8.0; firmware updated to latest). I have successfully connected my wireless laptop using WEP security, but I'm at wits end trying to get the Xbox 360 wireless adapter to work. (It worked just fine with my Netgear router until that router recently died.)
When I do the "Test Media Connection" routine (you XBox 360 users know what I'm referring to), the Xbox immediately recognizes the Network Adapter and indicates that it is connected to the Wireless Network, but it inevitably fails the next step in the process: IP Address. I have the set-up for the IP address to be assigned automatically by the router (which is set for DHCP Server enabled).
I have gone around the mountain innumerable times myself and then with well-meaning friends who say try this, try that, try this, try that. I've had to re-establish my laptop set-up so many times I wanna scream!
Are the Xbox 360 wireless adapter and the WRT54G even compatible? If so, what am I missing here? I'm not too technical and obviously in over my head, but this ought not be that hard.
Please, please do NOT respond unless you KNOW the answer! I don't mean to be curt, but I'm over / past "suggestions to try."
Thank you VERY much for your time and consideration if you can help me.

I don't think that the X-BOX adapter is not compatible to wireless rotuer .... there are few settings you can try on the router ... Access router setup page ... Please click on the tab "Application and gaming" and click on sub tab "Port range forwarding" 1) On the first line in Application box type in "Xbox", in start box type in 88, in end box type in 88, in protocol keep it both, in ip address type in 192.168.1.20 and give a check mark on enable box. 2) On the second line in Application box type in "Xbox", in start box type in 3074, in end box type in 3074, in protocol keep it both, in ip address type in 192.168.1.20 and give a check mark on enable box. 3) Now save the settings 4) Once you return to the setup page, click on the tab "Administration" and disable the UPNP and save the settings. 5) Now assign the given ip address on your xbox ip address :- 192.168.1.20 subnet mask :- 255.255.255.0 default gateway :- 192.168.1.1 Please assign the dns address on the xbox primary dns :- 4.2.2.2 secondary dns :- 192.168.1.1 6) Please try to test your xbox live. Hope it works ...

WRT54G & XBOX 360 Wireless Networking Adapter-Router doesn't see my SSID

I purchased a XBOX 360 networking adapter yesterday. I hooked it up and serched for networks and it doesn't see my SSID through the linksys router. Before I purchased the 360 adapter, I could hard hook it to the router and it worked fine. I called 360 and they suggested that I open my MAC on the Linksys Router so that it would recognize it, but I do not know how to do that. I know how to get into 192.168.1.1, but don't want to do anything crazy. Please advise. I'm not a novice, but not an advanced router owner. Thanks,
WRT54G v.8

SSID Broadcast should be Enabled on your router...
Open an Internet Explorer browser page on your wired computer(desktop).In the address bar type - 192.168.1.1...Leave username blank & in password use admin in lower case...
For Wireless Settings, please do the following : -
Click on the Wireless tab-
Here select manual configuration...Wireless Network mode should be mixed...SSID Broadcast should be Enabled...Check what is your SSID(change the SSID if it is Linksys)...Click Save Settings if you have changed anything...
Click on the subtab Wireless Security, if the Security Mode is WPA/WPA2 change it to WEP, if it is WEP take not of Key1(this is your wireless security)...
X-Box Setting :
1. Connect the appropriate wireless network adapter to the console. On the Xbox, a Wi-Fi adapter that connects to the Ethernet port (sometimes also called a wireless network bridge) must be used. Alternatively, the Xbox 360 is also designed to work with certain Wi-Fi game adapters that connect to a USB port.
2. Turn on the console and navigate to the wireless settings screen. On the Xbox, the menu path is "Settings -> Network Settings -> Advanced -> Wireless -> Settings" On the Xbox 360, the menu path is "System -> Network Settings -> Edit Settings."
3. Set the SSID (network name) on the Xbox to match that of the wireless router. If your wireless router has enabled SSID broadcast, the SSID name should appear pre-selected on the Xbox display. Otherwise, select the "Specify Unlisted Network" option and enter the SSID there.
4. Specify "Infrastructure" as the Network Mode. (Infrastructure is the mode used by wireless routers.)
5. Set the Security Type to match that of the wireless router. If your router uses WPA encryption and the type of adapter connected to the Xbox does not support WPA, you will need to change your router settings to use WEP encryption instead.
Note that the standard Microsoft Xbox 360 Wireless Network Adapter supports WPA while the standard Microsoft Xbox Wireless Adapter (MN-740) only supports WEP.
6. Save your settings and verify the network is functional.
On the Xbox, the Wireless Status screen displays whether a connection has successfully been made with the wireless router, and the Connect Status screen displays whether a connection has successfully been made through the Internet to Xbox Live.
On the Xbox 360, use the "Test Xbox Live Connection" option instead.

Airport and using a xbox 360 wireless

I want to convert to the apple world and a airport network. I am 99% there.
I have been readin many post's about xbox 360 not working on airport networks, i was woundering can you use a AirPort Express unit and hard wire in to the 360. so it would work like a wireless bridge.
Has any one tired this or hard wired a non wireless computer like this?

John Knowles wrote:
Hey I think, I just responded to this same topic in the Airport Express forum (?)
Anyway, I was going to post this as a sticky on the topic but this seems as good a place to put my info. I have an XBox 360 hardwired into my Airport network, works great. Here's my setup:
1. Main access point: Time Capsule 500GB (upstairs) plugged into Time Warner cable modem. Set to Wireless N, b/g compatible.
2. Bridge: Airport Extreme N base station (downstairs), extending my wireless network.
3. XBox 360 plugged into the downstairs base station via Ethernet cable.
4. TivoHD also plugged into the base station. Not important to this discussion, just to show that it works (and that it's nice to be able to hardwire all your AV devices).
Set your primary base station to be extendable, then configure your second base station as a bridge by allowing it to extend your primary network. Easy. Plug in the 360 and it will configure automatically, no need to go through all the PAINFUL configs when using wireless.
Just for the record, I also tried:
1. XBox 360 wireless adapter and my Time Capsule: would only work when I set my Airport network to "B only" mode, which is pretty useless. Stopped working altogether after I swapped wireless adapters and tried to switch back. I think it's a piece of junk, and the XBox's wireless setup could use an overhaul.
2. Linksys G Game Adapter: worked briefly with Time Capsule, then stopped working. Created it's own ad-hoc network despite being told not to. Can only setup using web utility on a Mac. Also a piece of junk.
**Final advice: if you have Time Capsule, do yourself a favor and buy an Express or another base station and hardwire your Xbox 360. You'll save yourself a lot of headache. An Express costs close to what an XBox wireless adapter costs anyway, so it makes more sense to go this route.**
Haha, you're a **** genius. I was going to buy a new n-compatible Airport Express anyway (been borrowing my mom's old Express thus far) – aaand I just got an Xbox 360. And also, by doing it your way, I will only have the power cord and the ethernet cable from the modem to my Time Capsule‚ all other devices (iPhone, MacBook Pro, PS3) will connect wirelessly, and the Express will do the same, and since its current position is like 1 meter away from the Xbox 360, this was truly one of my all-time highlights of a forum-solved problem...
Thanks!

Xbox 360 Wireless Network Adapter N and Liksys WRT54GX Router

When I configure the xbox 360 Wireless N adapter, as soon as i itroduce my WEP key all my internet conection goes down, in all my pc wirelessly and with the ethernet cable, i have to reset my router to connect to the internet again, Why is that?

Check if your XBOX is not set to a Static IP? If you have set the Static IP on your XBOX and if its in the range of your Router, then due to Ipconflict the Internet Connection must be getting Down down on all the computers.
If you have set the Static IP on your XBOX, then you need to set it to DHCP or Automatic and then try to connect to your wireless network on your XBOX.

WRT54G v6 - Troubles connecting XBOX 360 to XBOX Live?

I just purchased a new XBOX 360 and I'm finding that I can't connect to XBOX Live using my WRT54G v6 (firmware version 1.01.1).
If I connect the XBOX 360 directly to my DSL modem, I can connect to XBOX Live.
If I try to connect the XBOX 360 to the WRT54G v6 (using either a direct ethernet connection, or using the XBOX 360 Wireless adapter) I can't connect to XBOX Live.
When I run the diagnostic tests on the XBOX 360, all of my connection tests pass with flying colours.
Has anyone else had this problem? How do you fix it?

hi, i have just recently bought the wireless adapter for the 360, and i keep getting boot off xbox live when ever my brother turns his PS3 on or off. even when a house call is made or comes in i get booted. if my brother doesnt turn his PS3 on or a call doesnt come in or go out, i can play fine, but once one of those happens i get booted. noone knows what i can do, xbox told me to call linksys, i was never able to talk to a real person on the phone, just machines. does any one have a clue??? i was told to change my NAT, but it's open, so i dont know what to do.

Xbox 360 Wireless Control not working in W7 x64

Hey all,
I have read some topics in here about issues on a Xbox 360 Wireless Control connection in Windows 7 x64 (I'm on a Dell Inspiron n5110, 6gb ram, intel core i5). Thing is, in difference to all those threads, in my devices list there ain't any "unrecognized
devices" nor anything, so all the solutions listed don't work for me.
What I have done:
1) Installed the Accesories 1.2 for Windows 7 x64
2) Plugged the receiver to my usb (it got detected by windows, recognized and listed properly in the devices and printers, as a wireless receiver)
3) Turned the controller on, hitted the sync button on the receiver, then on the control... and I get a eternal green blink around the Xbox button, which never ends nor stays in one of the quadrants.
As I don't see nothing like "unidentified device" in the device admin, I simply can't use the "update drivers" stuff. What can I do, what am I doing wrong?
Thanks in advance...

Hi,
I would suggest you to follow these steps and check if the issue is resolved:
1. Verify that the accessory is an officially licensed Xbox 360 wireless accessory.
2. Examine or replace the batteries to make sure that you have fully charged the batteries in the Xbox 360 wireless accessory.
3. Move the receiver away from other devices that could interfere with the wireless communication between the receiver and the Xbox 360 wireless accessory.
Note: Devices such as wireless routers, cordless telephones, and microwave ovens can generate wireless interference.
4. If you are using a wireless keyboard or mouse, disconnect the keyboard or mouse and reconnect the the wireless gaming receiver. Then try reconnecting your Xbox 360 wireless device to the PC.
Also, you may try uninstalling and reinstalling the drivers for controller in device manager and check if this helps.
If the problem persists, then please contact Xbox support for further assistance. Here’s the link:
http://www.xbox.com/en-GB/support/xbox360/
Please Note: Since the site is not hosted by Microsoft, the link may change without notice. Microsoft does not guarantee the accuracy of this information.
Hope it helps.
Regards,
Blair Deng
Blair Deng
TechNet Community Support

WRT54GS Wont support Two XBOX 360s online at the same time

Just bought new Linksys WRT54GS to support two XBOX 360s live simultaneously. Can't log both on at same time. It kicks first 360 off when second one tries to log on. How can I fix this and have both NAT types open?

I'm having the same issue. I have comcast as ISP, Linksys modem BEFCMU10 V3, going to a Linksys router WRT54GS V4, two desk tops hardwired to the router, TiVo with a wireless and two Xbox 360s with Xbox wireless adaptors. Each Xbox 360 has a different Live account, one has mine the other has my daughters. Either by itself goes live just fine but as soon as the second unit is brought on the first kicked off. If left on they will take turns dropping off from Xbox Live. One night we alternately texted/chatted from both of our Xboxs to the same third party. When he had signed off for the night and showed be "offline" on my unit my daughters unit still showed him "online" until we shut her Xbox off. In addition the NAT always seems to change. Some times its open, others it's medium or strict. This seems to be related to having one or both Xboxs on. I found an article on segmenting your network by using two wireless routers and running the Xboxes through the router closest to the modem and everything else through the second down line router. I haven't tried it yet. Anything I'm missing? Something else I should try? I've talked to the Geeks and some tell you can't so it and others tell me sure it will but they want $$. I've talked to other gamers that tell they've had two Xboxs on Live with no problem.

Xbox 360 wireless adapter for windows 8.1.

would the xbox 360 wireless receiver adapter work with windows 8.1. because i'm having a problem that my controller keeps getting disconnected for no reason.

Hi,
Regarding your problems about not connecting the controller to the adapter, I suggest you replace the batteries or recharge the battery pack.
Meanwhile, I would like to verify if the controller is recognized in Device Manager. How about changing different USB ports?
Please reinstall the latest driver of the receiver adapter and the controller from Microsoft.
If the issue persists, I would recommend you to contact Xbox support for further assistance.
http://support.xbox.com/support/en/us/nxe/contactus.aspx
Regards,
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Airport extreme connecting with xbox 360 wireless adapter problems...help!!

Has anyone linked their xbox 360 wireless adapter to an Airport Extreme? I need help! Neither Apple nor Microsoft knew how to link the two devices. If anyone has successfully been able to make this work, your help will be much appreciated. Thanks guys

Yes - Mine works no problem. I have found that I have to unplug the Xbox360 wireless adaptor and plug it back in occasionally (if the green light is on everything is fine). Are you using the correct WPA Key?

WRT54G version 5 and Xbox 360 Wireless Controller

Similar Messages

Maybe you are looking for