WRT54GS connection using Windows Me

Hello,
A friend gave me his old Dell Insperon 8000 (using Windows Millennium) for my daughter to use. It needs a wireless card, so my tech friend installed a Trendnet 54Mbps wireless card that connects fine at his shop (router unknown). The problem is it won't connect to my Linksys WRT54GS router at home (switches between 100% and 0% signal strength, but mostly no signal)). My newer Dell Insperon 1525 (using Windows Vista) connect fine automatically. Do I have to change the settings on my Linksys router to get the older Millennium Dell to stay connected? If so, how do I go about it? Thanks.

Login to the linksys setup page and under Wireless tab,change the Wireless Channel to 11-2.462GHz.Under Advance Wireless Settings tab,Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 >>Click on "Save Settings"...Recheck the SSID(name) and Security key and then,try to locate the Wireless Network on the ME computer and connect it...
Which Wireless Security you are using on the router.You can also try to lower down the security level to WEP and then,try to connect.

Similar Messages

  • Problems connecting using Windows

    I use a Mac and can easily connect to the Airport but my friend can't connect using her PC. Her computer registers the system but it doesn't allow her access. It keeps asking her for a network key. What is that?
    Thanks.

    You must be using an additional wireless utility to configure your wireless network.
    Once you are connected to your wireless network using WZC you stay connected to it as long as you restart your laptop...Once the laptop is restarted both the utilities conflict disconnecting you from your wireless network...
    Locate the Utility under your Programs menu - 
    Either permanantly use the utility to connect to your wireless network or disable the Utility to let Windows connect to your wireless network.

  • Access Connections - Use Windows Logon grayed out

    I have seen multiple posts on this, but no solution. I am trying to configure acconn for PEAP, but in the user credential section, the Use Windows Logon is grayed out. I have tried reinstalling and checking off the box on the install, still no luck. Lenovo had me reload the laptop to factory, but that didnt help either.
    Suggestions?
    Ron

    Ok, are you logged on the system as having Admin privileged?  If not, then you can't change the Global Settings.
    I strongly suggest not deleting registry entries.  mgtitchenell mostly had it right, but instead do this:
    Go into Global Options in Access Connection, uncheck it, click OK and restart, then go back in and check it, click OK and restart.
    After this - the option should no longer be grayed out.
    If that doesn't work, then the problem mostly likely comes from some other GINA installed on the system that Access Connections doesn't recognize.   Look back at the registry entry (HKLM\Software\Microsoft\Windows NT\CurrentVersion\Winlogon) and look for an entry that either has the word GINA mixed up in it, or that points to some file that end in .dll
    Disk encryption software and some VPN programs put in their own DLL (or things like Novell Netware client)

  • WRT600N not able to connect using windows 7 desktop.

    all other computers on network still working fine.  Did power cycle and tried to run disk in compatibility mode.  Not establishing Ip and cant get into the manual setup with 192.168.1.1 either.

    I have a similar problem...
    The Linksys WRT600N is working fine withe all the computers in the house, but the new computer I bought has Windows 7 on it and I cannot acces the internet.
    It is very strange that I can send and receive emails (on wireless) from this new computer but cannot acces the browser.
    I tried downloading Mozilla (I thought the Internet Explorer was not working) but Mozilla does not work either.
    Any chance to help me?
    Thanks!

  • Can't connect to Easy VPN Server using Windows 7 inbuilt VPN client

    Hi Everyone,
    I would like your help to resolve a vpn issue I am having with my Windows 7 inbuilt vpn client. I am trying to connect to an Easy vpn server on a Cisco 2951 ISR G2. Well, I can connect using Cisco vpn client v5.07 but I can't connect using Windows 7 inbuilt vpn client. Is there any configuration that I am missing so that I can connect using Windows 7 inbuilt vpn client to connect to the vpn server?
    Thank you.

    Hi MindaugasKa,
    Base on your description, your case must is the NPS client can’t pass the NPS policy.
    The NPS client can’t connect the network may have many reason, such as the Network Access Protection Agent service not started successful, the certificate not issued properly,
    please offer us information when your Windows 7 client denied, such as event id, original error information, screenshot.
    More information:
    Extensible Authentication Protocol (EAP) Settings for Network Access
    http://technet.microsoft.com/en-us/library/hh945104.aspx
    Network Access Protection in NPS
    http://msdn.microsoft.com/en-us/library/cc754378.aspx
    Appendix A: NAP Requirements
    http://technet.microsoft.com/en-us/library/dd125301(v=ws.10).aspx
    802.1X Authenticated Wireless Access Overview
    http://technet.microsoft.com/en-us/library/hh994700.aspx
    Connecting to Wireless Networks with Windows 7
    http://technet.microsoft.com/library/ff802404.aspx
    The related thread:
    NPS 2012 rejects windows 7 clients after upgrade from 2008 R2. Requested EAP methods not available
    http://social.technet.microsoft.com/Forums/windowsserver/en-US/44af171f-6155-4f2e-b6c7-f89a2d755908/nps-2012-rejects-windows-7-clients-after-upgrade-from-2008-r2-requested-eap-methods-not-available?forum=winserverNAP
    I’m glad to be of help to you!
    We
    are trying to better understand customer views on social support experience, so your participation in this
    interview project would be greatly appreciated if you have time.
    Thanks for helping make community forums a great place.

  • Remote desktop connection in windows 7 pro

    I have a problem accessing remote desktop connection using windows 7 64 bit.
    My remote desktop connection shell version 6.3.9600 shows the Network Level Authentication is not supported.
    My other computer also win 7 pro 64 bit has a different shell version 6.2.9200 that supports Network Level Authentication.
    How do I go backwards to shell 6.2.9200?
    I have been trying use remote desktop using the more robust security and could not figure out why I could not log.
    I have screen shots of the two shells and my system screens

    Hi,
    Configure Network Level Authentication
    Click Start, click Run, type regedit, and then press ENTER.
    In the navigation pane, locate and then click the following registrysubkey:HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Lsa
    In the details pane, right-click Security Packages, and then click Modify.
    In the Value data box, type tspkg. Leave any data that is specific to other SSPs, and then click OK.
    In the navigation pane, locate and then click the following registrysubkey:HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\SecurityProviders
    In the details pane, right-click SecurityProviders, and then click Modify.
    In the Value data box, type credssp.dll. Leave any data that is specific to other SSPs, and then click OK.
    Exit Registry Editor.
    Restart the computer.
    Hope this helps!
    Andy Altmann
    TechNet Community Support

  • Deploying the Cloud service using Windows Authentication

    Hi,
    I have a VPN Connectivity established to other VM Server where the DB is also installed. Now I a have created an application with DB connectivity
    I am able to connect the DB server using SQL authentication but how can I connect using Windows Authentication?
    What configuration changes I have to do in web.config or I have to modify any more changes else where?
    Thanks & Regards,
    Suresh Sahu

    Hi,
    Based on your description, you have connected to DB server using SQL authentication, I suggest your read the following link, and do some change in SQL that installed in the VM, hope it helps. If I misunderstand, please feel free to let me know.
    #http://msdn.microsoft.com/en-us/library/dd787978.aspx
    Best Regards

  • BO -  Problem to connect through windows client

    Server OS: Windows Server 2003 SP2
    BOE Version: XI Release 2
    Client SO: Windows XP Professional SP2
    DB: Oracle 10 v 10.2
    Problem:
    I have a BOE XI Release 2 installed on a server and if I try to connect via WEB everything is perfect but when I try to connect using windows clients (Designer, DESKiu2026)
    I am getting the following error:
    " No se puede acceder al repositorio. (USR0013)"
    u201C[repo_proxy 13] SessionFacade::openSessionLogon with user info has failed(Error en el transporte: Fallo en la comunicación.(hr=#0x80042a01)u201D
    I'm using the standard port which is the 6400.
    I hope your comments.
    Thanks!

    Hi,
      Are you using any authentication ?
    If you are using LDAP, then try this...
    Symptom
    Error logging onto Desktop Intelligence or Designer using LDAP authentication:
    "(USR0013) [repo_proxy 13] SessionFacade::openSessionLogon with user info has failed (The LDAP authentication could not log you on.) Verify your logon information. If your account is under a different domain as o=u2026, please enter your dn (hr=#0x80042a01)."
    Reproducing the Issue
    Configure LDAP authentication
    Error appears from a client computer running Desktop Intelligence or Designer
    Logon to Desktop Intelligence or Designer on the server works
    Cause
    LDAP authentication from the client connects directly to the LDAP directory without passing the CMS
    The server has been configured on the firewall, but not the client computer
    Resolution
    Configure the firewall for the client machines to pass, so that they can reach the LDAP directory

  • HT3986 I installed windows 7 to my macbook pro, but my mousepad does not work in windows 7 and also i can not connect my windows 7 to projector, but i can use my macbook's mouse pad and i can connect my mac to projector,so please help me for windows 7 pro

    I installed windows 7 to my macbook pro, but my mousepad does not work in windows 7 and also i can not connect my windows 7 to projector, but i can use my macbook's mouse pad and i can connect my mac to projector,so please help me for windows 7 problem

    i try to download now, do you think when i download and install the windows support software, can i fix the problem?

  • I am using windows 8.1. But I recieved the error This apple id is valid but is not an icloud account. How can I get connected to Icloud?

    I am using Windows 8.1. When I try to connect to Icloud I get the Message: This Apple id is valid, but is not an icloud account.
    How can I get connected to Icloud?

    Hello pmarrone,
    You may only sign up for an iCloud account via one of the following systems or devices.
    You can sign up for iCloud on an iPhone, iPad, or iPod touch with iOS 5 or later, or through System Preferences on a Mac with OS X Lion v10.7.4 or later. Just follow the setup instructions for your iOS device or Mac.
    Creating an iCloud account: Frequently Asked Questions
    http://support.apple.com/kb/HT4436
    Cheers,
    Allen

  • HT4972 I AM USING WINDOWS XP. WHEN I AM CONNECTING MY IPOD TOUCH  MODEL NO. MC 008LL TO MY PC ,CHARGING INDICATION IS COMING BUT NEITHER THE WINDOWS NOR THE LATEST VERSION I TUNE DETECTING MY IPOD. IT IS ALSO NOT SHOWING IN I TUNE WINDOWS.

    I AM USING WINDOWS XP. WHEN I AM CONNECTING MY IPOD TOUCH  MODEL NO. MC 008LL TO MY PC ,CHARGING INDICATION IS COMING BUT NEITHER THE WINDOWS NOR THE LATEST VERSION I TUNE 10.6.3 DETECTING MY IPOD. IT IS ALSO NOT SHOWING IN I TUNE WINDOWS."DEVICE LIST" IS NOT DISPLAYING IN LEFT HAND SIDE WINDOW OF I TUNE. BEFORE IT WAS WORKING IN ITUNES 9 AND I WAS USING IT. BUT NOW IT IS  NOT DETECTIN AT ALL. SO PLEASE HELP ME WHAT TO DO?

    Have you tried here:
    iOS: Device not recognized in iTunes for Windows

  • Anyone else having an issue with TCP connections using iCloud for Windows?

    Hi,
    Before I asked this question, I did wait to see if any related questions came up, but none did, so I submit it now.
    On my admittedly older laptop running Windows 7 64b Home, I've run into difficulties with the iCloud for Windows app to the extent that I had to uninstall it.
    It would that, as my laptop was running, in the background, iCloudServices.exe would endlessly iterate TCP connections, which, while not actively sending or receiving any data, after some hours would number over 100 instances, taking up resources, and grinding my laptop's WiFi connection to a grindingly slow pace. I ended up, within the app, turning off everything, iCloud Drive and Photos, (I never used bookmarks), but still this would continue to occur.
    I contacted Apple Support, explaining what was going on, and they stated they only dealt with IOS and gave me a Microsoft Support number. When I called Microsoft support, I came more and more to the realization that the issue was specifically with the iCloud for Windows app, as that was the only software that was endlessly creating and not closing TCP connections as it was. How was Microsoft supposed to solve an issue with Apple code?
    So I called Apple back, whereupon they insisted it was a Microsoft issue. I explained other cloud services installed on the same computer were not having the same issue, it was unique to ICloudServices.exe. They stated they only dealt with IOS. I stated I purchased an iPad Air less than 7 months ago, and was trying to run iCloud in support of that.  They again stated they only dealt with IOS, and suggested I again try Microsoft. I asked them if it was reasonable to expect Microsoft to solve issues with Apple code? They said regardless, there was zero support offered for anything having to do with Windows, and all I could do was uninstall the app, which I did, though that did not feel very satisfactory to me. My thinking is, if Apple writes a Windows app in support of their hardware, they should offer support for it.
    Anyway, I was just wondering, is this an issue unique to me? or have others experienced a similar issue? I found this issue by opening the Windows Resource Monitor, looking under the Networking tab, and scrolling through the TCP Connections section to find 100+ concurrent iCloudServices.exe instances listed, whereas even Chrome, with multiple tabs and extensions, topped out at around 20.
    My one month old Desktop, DYI, sports a solid Asus 1150 MoBo, i7-4790k cpu, 16GB Ram, and an EVGA GTX 970 video card. I list some specs only to illustrate this computer has no hardware issues in comparison to my long in tooth laptop. On this desktop, running Win 8.1 Pro 64b,  at least as many, identifiably Apple, background service TCP connections are created even compared to Chrome, regardless of many tabs being open, many extensions, and even some related apps. Adobe does not even come close, though I run the full CC subscription. On this new computer, running Windows 8.1 Pro 64b, there are currently over 50 TCP connections and loopbacks that do not identify themselves, with just a - for the Image, and PID. With the experience on my laptop, I wonder how many of these are generated by Apple software, if not specifically iCloud software?
    The frustrating aspect of these connections is they seem in no way active, While the Chrome and Adobe connections can be seen to be transferring data, as long as I am not running iTunes, or so have my iPad actually plugged in, it seems 99% of the time these iCloudServices.exe connections are just taking up ports, neither sending nor receiving any data discernable to me under the Processes with Network Activity, or Network Activity lists, both displayed in the same window as the TCP Connections in the Windows Resource Monitor.
    Though I am fairly ignorant as regards coding, it seems as if there is no call to close a connection, very specifically, iCloudServices.exe, when it is no longer needed, and the next time a connection is needed, a new one is opened, rather than accessing the one previously opened. The only other reason I could imagine this might be occurring is if my Norton Internet Security software might mask and/or block the port after a certain time of inactivity.
    Anyone out there have any ideas or advice about this? Thanks in advance.

    Thanks jared,
    I'm still dealing with this issue through Apple. Some time after I posted this, I contacted Apple again. They did start a case up for me, as I was experiencing the same behavior on two different machines, with two different versions of Windows.
    So far it remains unsolved. I've logged iClouds for Windows on my desktop, which is brand new, then logged for awhile after completely uninstalling Norton Security Suite, depending on the Microsoft security for some time, and finally logged after I uninstalled iCloud for Windows, restarted, installed a clean download, and connected using a completely different test account, which Apple set up for me. None of this made any difference. Looking at the logs, it seems every 10 minutes, iCloudServices.exe creates a new TCP connection to confirm I'm using less than 5GB on iCloud, (which I am by a good margin, using less than 2GB), it seems this connection is not closed, and when the next iteration rolls around 10 minutes later, a new TCP connection is created. I come very close to having 6 TCP connections created per hour, until I restart my computer. This works out to... 6 x 24 = 144/day.
    Perhaps the article you posted will shed some further light on this. I'm thinking seeing the state of the connection through netstats, at the least, could help.
    For the last week, I've been putting a hold on further logging, as Apple wants me to create a new user account on one of my computers, install iCloud for Windows there, and log it running in the other account. This however basically means I cannot use my computer for a fair number of hours, and I've been busy enough with work the past week that I haven't the time or energy to afford to set this up and run it. I've had need of my computers too much for the past week.

  • How do I connect airport extreme to seagate hard drive using windows

    How do I connect airport extreme to seagate hard drive using windows?

    First the AirPort Extreme Base Station (AEBS) cannot share out an external HDD attached to its USB port unless it is formatted in either HFS+ or FAT16/32. It will not work if the HDD is formatted in either NTFS or ExFAT.
    If the HDD is formatted properly, when you access the AEBS with the AirPort Utility, does the HDD show up properly on the Disks tab of the utility?
    If it does, then you would access the HDD as any other network share, using the following format: //servername/sharename. In the case of the AirPort Disk (a HDD attached to the USB port of either an Extreme or Time Capsule), the "servername" would be the Extreme's Base Station Name, and the "sharename" would be the volumename of the HDD.

  • Why can't I connect one Windows 8.1 PC to other Windows 8.1 PCs in my workgroup when using a Microsoft Account?

    I finally decided to convert some of my local accounts to Microsoft Accounts on my Windows 8.1 PCs. Big mistake to this point.
    I have two PC's with the same Microsoft Account set up, neither PC can browse to the other or map a drive through browsing.
    I'm not using a homegroup. My daughter has one setup on her laptop and desktop, and I don't want my PC's on her homegroup. Until Microsoft makes it possible to have 2 homegroups on the same subnet, this is not an option.
    The local accounts on both PC's have no problem browsing, mapping, etc. I can connect to the other PC's just fine using local accounts, so I know physical connectivity isn't an issue, neither is my anti-virus or really anything else system wide on either
    computer. 
    I just can't attach automatically using a Microsoft Account. I have to manually map a drive every logon/reboot.
    I have also found that running a logon script doesn't work. The drives will not map automatically.
    The Microsoft Account users can map a drive using "Connect using different credentials." However, the credentials don't hold across reboots.
    I can manually (using either a Microsoft Account or a local account) map a drive using "net use" which then opens up all of my mapped drives and allows for browsing to the other PC. However, this doesn't work across reboots/logons either.
    Entering credentials in the Credentials Manager (Whether I use the Microsoft Account credentials or one of the local user credentials) doesn't work across reboots either.
    Yes, I have the same Microsoft Account setup on both PCs. I have tried giving them both Admin and Standard user rights on both PCs.
    I have turned off UAC as recommended in some posts.
    Again - This problem is ONLY related to MICROSOFT ACCOUNTS, not local accounts.
    I have put a batch file on the desktop with a "net use" statement in it to connect as a work around, but this is very annoying and truly unacceptable. Is there anyway to make this work seamlessly without running a batch file or something else where
    the password exists on the PC in clear text?
    I can't find other posts asking this question - am I the only one who is trying to do this? What memo did I miss?
    Thanks for any help!

    Hello Steve Hengen,
    I apologize for the delay.
    I have test in my own environment and can normally map the network driver when logon as Microsoft account.
    Do you check the option Reconnect at logon?
    If you use Connect using different credentials, do you check the option Remenber my credentials?
    Please take a look at the following article about map a network drive.
    http://windows.microsoft.com/en-HK/windows-8/create-shortcut-to-map-network-drive
    Best regards,
    Fangzhou CHEN
    Fangzhou CHEN
    TechNet Community Support

  • [Forum FAQ] "Unable to connect to the server by using Windows PowerShell Remoting" error while installing RDS roles on Server 2012 R2

    When you try to install RDS role on server 2012 R2 using standard deployment, this issue may occur (Figure 1).
    “Unable to connect to the server by using Windows PowerShell remoting”.
    Figure 1: Unable to connect to the server by using Windows PowerShell remoting
    First of all, we need to verify the configurations as it suggested:
    1. The server must be available by using Windows PowerShell remotely.
    2. The server must be joined to a domain.
    3. The server must be running at least Windows Server 2012 R2.
    4. The currently logged on user must be a member of the local Administrators group on the server.
    5. Remote Desktop Services connections must be enabled by using Group Policy.
    In addition, we need to check if the “Windows Remote Management “service is running and related firewall exceptions have been created for WinRM listener.
    To enabling PowerShell remoting, we can run this PowerShell command as administrator (Figure 2).
    Enable-PSRemoting -Force
    Figure 2: Enable PowerShell Remoting
    However, if issue persists, we need to check whether it has enough memory to work.
    By default, remote shell allots only 150 MB of memory. If we have IIS or SharePoint App pool, 150 MB of memory is not sufficient to perform the remoting task. Therefore, we need to increase
    the memory via the PowerShell command below:
    Set-Item WSMan:\localhost\Shell\MaxMemoryPerShellMB 1000
    Then, you need to restart the server and the issue should be resolved.
    You can get more information regarding Remote Troubleshooting by below link:
    about_Remote_Troubleshooting
    If you need further assistance, welcome to post your questions in the
    RDS forum.
    Please click to vote if the post helps you. This can be beneficial to other community members reading the thread.

    i found another possible reason, this solution worked for me:
    http://oyvindnilsen.com/solution-for-powershell-remoting-error-it-cannot-determine-the-content-type-of-the-http-response-from-the-destination-computer/
    I tried to set up powershell remoting on a server and kept getting this error:
    Enter-PSSession : Connecting to remote server failed with the following error message : The WinRM client cann
    ot process the request. It cannot determine the content type of the HTTP response from the destination comput
    er. The content type is absent or invalid. For more information, see the about_Remote_Troubleshooting Help to
    pic.
    After a bit of troubleshooting I discovered that the problem was that the authentication packets was to big (over 16k), this will cause WinRM to reject the request. The reason for authentication packets getting too big can be because the user is member of very
    many security groups or in my case because of the SidHistory attribute.
    The solution was to increase the MaxFieldLength and MaxRequestBytes keys in the registry under HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\HTTP\Parameters
    If the keys does not exists you can create them, be sure to use the DWORD type.
    I sat MaxFieldLength to DEC value 40000 and MaxRequestBytes to DEC value 32768 and rebooted the server. Problem solved.

Maybe you are looking for