X301: Wireless error code 10

Hey
I have just got an X301 and downgraded it to XP using hte supplied downgrade pack. The wireless is not working though. It says This device cannot start (error code 10). I have tried installing all new intell drivers from intel as well as lenovo and it has not fixed the problem. I have tried uninstalling the device adn reinstalling and it also does not work.
Has anyone else had this problem?
Mahcine Type = 2776 - A17
Thanks
Moderator note: Type added to subject line for clarity.
Message Edited by Agotthelf on 22-04-2009 09:08 AM

Hi Tzetz,
You can try booting from LiveCD of Ubuntu, assuming that Ubuntu identifies the device, if it does but the card reader wouldn't work, then it would possibly be hardware issue.
Also, have you run a full diagnostic test on the system via ThinkVantage Toolbox?
I know, reinstalling Windows can be pain in the neck, however it would help in determining if this is software problem or hardware's fault.
Hope this helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

Similar Messages

Re: Satellite Pro C870 - No Wireless, Error code 43

Have two new Satellite Pro C870's where the wireless was being disabled every second startup. Wireless NIC in device manager had an exclamation mark and was showing "Windows has stopped this device because it has reported problems. (Code 43)"
After performing a system restore as advised by support the issue was still there.
Just before sending the two laptops off for repair I undid a setting called "fast boot" in the bios (otherwise set using a Toshiba utility).
Issue seems to have cleared after this.

Hi
You are using Win 8. Right?
> Have two new Satellite Pro C870's where the wireless was being disabled every second startup
First of all you should know that Windows 8 does not perform a real shutdown.
It goes just in hybrid mode.
Maybe the error 43 is related to the fact the Win 8 and notebook did not shut down as you expected from a system like Win 7.
If you would search for error code 43 using google, you will get a lot of hits and mostly its system / driver issue.
So first of all I recommend disabling the hybrid mode and performing complete shut down:
+Perform a complete shutdown in Windows 8+
http://aps2.toshiba-tro.de/kb0/TSB2B03EY0002R01.htm
secondly try the WLan driver update.
Regarding the other issue
>Also had an issue with the function of turning on when the panel is opened: this would cause the laptop to turn back on immediately after shutting down.
This is also an Windows 8 feature which can be disabled:
+Why does my Windows 8 notebook start automatically when opening the display lid?+
http://aps2.toshiba-tro.de/kb0/FAQ2C03FA0001R01.htm

New HP wireless printer install gives me Error Code 43

I just bought the HP wireless and networking capable all-in-one printer, the C309 series (no indication of exact model number anywhere on the machine, but the maybe it's the C334, since that's near the serial number on the back.
I connected it to my wireless network with no troubles. I inserted the install disc into my macbook pro, and got past the installation, to the setup step when I got the news:
"The operation can't be completed. An unexpected error occurred (error code -43)."
Does anyone have any ideas as to what the problem is here?

Try here:
http://discussions.apple.com/forum.jspa?forumID=1224
Al

Lenovo 3000 N100 Network issue / Wireless Stack initialization failed, error code 117

Hi,
Lenovo 3000 N1000 with 1GB Ram, Win XP SP2, purchased in May 2006. WLAN network with WPA-PSK key worked without any issues so far and is still accessible with PC.
After transferring music via from my notebook to my mobile Bluetooth all network adapters seem to be disconnected. Neither Access Connections (AC) nor Windows can find any wireless network. Also if I try to configure any LAN, WLAN with Windows I get the message that all network adapters have been removed. However I cannot spot any issue in the device manager as all parts are shown to be working OK.
This is what I've done so far:
1) Checked Radio switch ---> on
2) FN +F5 --> connection on
3) Uninstalled AC, downloaded and installed most actual version (5.00 Build 7VCX32WW)
4) Installed new version for wireless driver for Intel(R) PRO/Wireless 3945ABG (version 12.0.0.82)
Still, even if I uninstall AC to check if WLAN is working at all, Windows gives the error message that all network components have been removed.
Diagnose Tool gives the following output:
"Wireless Stack initialization failed, error code 117"
Logfile:
Description : Intel(R) PRO/Wireless 3945ABG Network Connection
Type : Wireless LAN Adapter
DriverVersion : 10. 5. 1. 59 ----> why is the old driver version??????????
PNPID : PCI\VEN_8086&DEV_4227&SUBSYS_10118086
SupplicantVersion : AEGIS Protocol (IEEE 802.1x) v3.5.3.0
ERROR AcSvc( SYSTEM(Prvlg).1108.4580) [9/3]11:04:15:703 CAcGolan::GetRadioStateInDriver: Golan API GetRadioState() missing!
Hope this is enough information for anyone of you in order to suggest any solution. As I could see from previous threads some of you experienced similar problems in the past and could fix them somehow. However I couldn't find anyone with exactly the same problem.
Thanks much in advance for any advice you might have.
Flo

Hi
I have this problem also with my Lenovo 3000 V200.
Sometimes when I boot up the PC it will connect to the network and everything works just fine.
At other times, after boot, the "wireless stack initialization failed, error code: 118" problem occurs
and the only way to solve it seems to be a PC restart. Nothing else I do will bring the network up.
If I study the Networking tab in Task Manager it indicates that no adapters are available (wired eth.
access also fails). At a few occations connectivity have failed alltogether (i.e. a reboot have not solved
the problem). Last time this occured I had to reinstall the complete system (from a previous backup)
to get networking up.
I have tried different versions of Access Connections (5.02, 5.12, 5.21) and the same problem occurs
at seemingly random instances in time. This is obviosly a problem with the Access Connections software
since the Wireless networking works fine when I let windows manage it...
Anyone with a fix?
/Fredrik

Wireless net does not work after installing SP1 for Vista - Error code 10

After installing Vista SP1 on my computer (T61 - Vista Business 32 bit) my intel 82566mm wireless net does not work.
Windows says "Error code 10" and suggests that I update the driver. I have downloaded the newest driver via another computer, but it does not help. Still error code 10.
Any one else has the same problem?

I fixed the problem. Uninstall iTunes and then reinstall it clean. Looks like upgrading is problematic.

Can I connect a PS3 wirelessly using internet sharing from my ethernet-wired iMac. It works for my Nook e-reader, but the PS3 give a DNS error code 8070102, I've tried alternate DNS settings, but no luck.

Can I connect a PS3 wirelessly via the built-in AirPort card using internet sharing from my ethernet-wired iMac? It works for my Nook e-reader, but the PS3 give a DNS error code 8070102, I've tried alternate DNS settings, but no luck.

Can I connect a PS3 wirelessly via the built-in AirPort card using internet sharing from my ethernet-wired iMac? It works for my Nook e-reader, but the PS3 give a DNS error code 8070102, I've tried alternate DNS settings, but no luck.

Recent Cisco "update" to E4200 produced Error Code 3018, which ended wireless.

The update "failed," due to an "unexpected error." Wireless connection is disabled, although, as you have probably noticed, I can still connect to the internet (using an ethernet cable from my router to my laptop OSX 10.6.8). Error Code 3018 is unknown to Cisco's website. Any ideas? Or should I just start over with the installation disk for my E4200 router?
Solved!
Go to Solution.

Thanks. I was going to go there, but as last resort I plugged in the ethernet connection to the router and the wireless came back to the other machines. Still seems to work fine on both wired and wireless. Again, thanks for the reply.
-WE

Error code 10 for Intel 5300 Wireless Card

Hi,
I tried to install a new Intel 5300 Wireless Card in my Thinkpad T400.
However, it is not very successful.
After I installed the driver, I find a yellow exclamation point on the 5300 Wireless Card on the device manager and an error code 10 (can't start device).
I have tried to re-install the driver but still no luck.
Could anyone help for this?
Thanks a lot
Here is some information might be useful:
Operating System: Windows XP (SP3)
Driver download from Lenovo: http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-70504
Wireless Card bought from ebay (The seller said this card can support IBM/LENOVO T400).

Unless the card is a Lenovo Branded card, it won't work. But since you aren't complaining about an error in BIOS about an unauthorized card, then you also might have put it in the wrong slot.
Check the Hardware Maintenance Manual for your particular system and make sure you have it in the WLAN slot, not the WWAN slot.

Error code 0x803C010B when printing wirelessly: Has anyone found a solution yet?

I read all of the Microsoft forums regarding this issue but no one seemed to find a reliable solution. When there was a solution for one person, then it didn't work for someone else.
I called MS tech support, and they told me that they have received many calls about this error. The tech said that only MS could fix it and she charged me $100, with a 100% guarantee that it would be fixed. She evaded each time I asked her what
was the root cause of the error.
MS tech noticed three corrupted files from a Windows update, then started searching for viruses and malware, of which she found several, even though I had Norton protection. Then she tried to sell me a different anti-virus program, for more money,
which I declined until they could tell me the root cause of the problem.
Unfortunately I had an appointment so I left the tech working on my computer remotely. When I returned the problem was still not fixed. Printer still shows as offline or even turned off, when it is neither of these things, and I receive the above-referenced
error code when I try to troubleshoot.
I have a follow-up call with a MS tech today. I will post updates to this. It seems that they do not know how to fix it, either.

I'm having the same issue but with HP Photosmart 7525 and HP LaserJet P1102W. Both worked fine until earlier this week when I "shut down and updated" my computer. I keep deleting the printers from my computer and reinstalling them;
they work temporarily then tell me they are "offline" when, clearly, they are not.

Officejet 6500 wireless question: error code (0x61011bed)

The error code came up after copying a 7 page document. First showed a paper jam. Found no paper in printer or doc handller. What does the error code mean? Thanks, in advance.

Hello rusty1roe, and welcome to the HP Forums!
I see you're having a 0x61011bed error. I would love to try and help with that!
First thiong I would suggest would be a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
If that doesn't resolve your issues, I would suggest following through with the steps listed in this document on A 'Carriage Jam' or '0X610000F6' Message Displays on the All-in-One.
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Hi, I have an HP Officejet 6500a Plus wireless printer and I am getting an error code 0X61011BED.

My printer shows an error code 0x6101bed and when it tries to print the is a very loud clicking sound that lasts about 2-3 seconds before the paper jam error shows up. I've looked in the machine but I do not see any paper jammed anywhere. What could be the problem and how can I fix it.
This question was solved.
View Solution.

Hi,
If you think it is coming from the "clicking noise", it could be cartridge carriage related. Especially, as the carriage moves side to side. Since your printer is only two weeks old, if it were me... I'd call the tech support center at 1-800-HPINVENT. They might have additional troubleshooting to try. Generally, the 0x error messages have to do with the cartridges and show up on the front panel during printing and resets typically take care of error message.
Say Thanks by clicking the Kudos Star in the post that helped you. Please mark the post that solves your problem as Accepted Solution.
I am employed by HP

The operation can't be completed because an unexpected error occurred (error code -50)

I have a Seagate Central 3tb NAS (latest firmware) attached to my wireless router (Netgear wndr3400v3). I have a late 2011 macbook pro with Yosemite on it. When I go through finder to use my NAS I keep getting "The operation can’t be completed because an unexpected error occurred (error code -50)" . I only get it when I am trying to copy a big folder with other folders and files with in. I can copy a single file or create folders. If i try to copy a folder with 100 pics in it then I get the error. I can create the folder on the NAS and select all 100 files. When I drag them to the NAS, then they copy with no problems. Every so often my time machine has an error and says that it has to create a new backup. I read some where to make sure that "put hard disk to sleep when possible" should be selected in the energy saver in preferences. Still no luck. A can also drag any file from the NAS back to my laptop or view them from the NAS with no problems.
Thanks for any help in advance.
Billy

Hi there,
Well I have exactly the same problem! Recently I reset my WD My book White light (2 x 1TB RAID disk), due to the fact that the disk ran full because of TimeMachine.
I reset the disk, and now I can only write some files to it, but most give this error code.
I wrote to WD, but they could not give an answer.
Q: did you update the firmware? Maybe that is causing the problem, in that it is maybe not consistant in the filesystem?

Two Days of Restore Error Code 6... HELP!!!

I have an iPod Touch that's about two years old. I no longer have access to the laptop that it is normally synced to, so I downloaded iTunes on the family computer. After hours upon hours of problems (not syncing, or showing that it successfully synced but getting a "no content" error once it turned back on) I thought maybe it was my iPod that was messing up and not the computer. I reset my iPod through holding down the home button and the power button, and I'm now at the screen that shows the USB cord with an arrow pointing towards the iTunes symbol.
I tried to restore on iTunes, and it will get all the way through until "verifing restore," and then I will get a pop up that says the process could not be completed because of an unknown error (error 6.)
I uninstalled iTunes and installed an earlier version of iTunes, but then my computer wouldn't even recognize my iPod. I reinstalled the latest version of iTunes and Quicktime. Still getting the same error code.
I am on an Administrator account, running Windows Vista 64 bit, and everything is up-to-date. All anti-virus and firewalls are turned off. I've followed all of the steps outlined on the Apple site, and I am down to paying $29 for a phone call to Apple. (Ha! Over my dead body!) I don't have another computer to try it on. I've used two different iPod cords (mine and the cord from another iPod), and have tried out all of the USB ports on the computer.
I'm really hoping someone could help me with this before I lose my mind.
I'm fairly computer literate, but I'm not a whiz. Please don't feel the need to break things completely down into laymans terms, but please don't use pure tech-speak(:
Diagnostics:
Microsoft Windows Vista x64 x64 Home Premium Edition
Service Pack 2 (Build 6002)
HP-Pavilion NC686AA-ABA a6700y
iTunes 10.4.1.10
QuickTime 7.7
FairPlay 1.12.20
Apple Application Support 2.0.1
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.1.2
Apple Mobile Device Driver 1.57.0.0
Bonjour 3.0.0.2 (333.2)
Gracenote SDK 1.9.1.485
Gracenote MusicID 1.9.1.102
Gracenote Submit 1.9.1.133
Gracenote DSP 1.9.1.43
iTunes Serial Number 00B3B0A00BAFB508
Current user is not an administrator.
The current local date and time is 2011-09-28 18:09:41.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is supported.
Video Display Information NVIDIA, NVIDIA GeForce 6150SE nForce 430
**** External Plug-ins Information **** No external plug-ins installed.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name:     {154BA537-EF26-4015-BE91-6ACFA30865E5}
Description:     USB Wireless 802.11 b/g Adaptor
IP Address:     0.0.0.0
Subnet Mask:     0.0.0.0
Default Gateway:     0.0.0.0
DHCP Enabled:     Yes
DHCP Server:
Lease Obtained:     Wed Dec 31 17:00:00 1969
Lease Expires:     Wed Dec 31 17:00:00 1969
DNS Servers:
Adapter Name:     {3BF6C369-3C76-4358-997A-8DE3B494BFE8}
Description:     NVIDIA nForce 10/100 Mbps
Ethernet IP Address:     192.168.254.3
Subnet Mask:     255.255.255.0
Default Gateway:     192.168.254.254
DHCP Enabled:     Yes
DHCP Server:     192.168.254.254
Lease Obtained:     Wed Sep 28 17:12:00 2011
Lease Expires:     Wed Sep 28 17:11:59 2011
DNS Servers:     192.168.254.254
Active Connection:     LAN
Connection Connected:     Yes
Online:          Yes
Using Modem:     No
Using LAN:     Yes
Using Proxy:     No
SSL 3.0 Support:     Enabled
TLS 1.0 Support:     Enabled
Firewall Information
Windows Firewall is off.
ZoneAlarm Firewall is installed.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was successful.
Connection attempt to purchasing from iTunes Store was successful.
Connection attempt to iPhone activation server was successful.
Connection attempt to firmware update server was successful.
Connection attempt to Gracenote server was successful.
Last successful iTunes Store access was 2011-09-28 17:14:05.
**** CD/DVD Drive Tests ****
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.0.1),   E: TSSTcorp CDDVDW TS-H653Z, Rev 4403 Drive is empty.
**** Device Connectivity Tests **** iPodService 10.4.1.10 (x64) is currently running. iTunesHelper 10.4.1.10 is currently running. Apple Mobile Device service 3.3.0.0 is currently running. Universal Serial Bus Controllers: Standard OpenHCD USB Host Controller. Device is working properly. Standard Enhanced PCI to USB Host Controller. Device is working properly. FireWire (IEEE 1394) Host Controllers: VIA OHCI Compliant IEEE 1394 Host Controller. Device is working properly. Most Recent Devices Not Currently Connected: iPod touch (2nd generation) running firmware version 4.2.1 Serial Number:     8K9436WJ75J **** Device Sync Tests **** No iPod, iPhone, or iPad found.

This Question can be best answered by someone who had the Same error pop up, but I'll try my best. You have an iPod touch 2nd Generation and you don't have anymore warranty for it. I hope you didn't jailbrake it or did something illegal with it like putting a new software on it that should not be on there. Here we go:
Go to your Friends house or anybody else you know that has iTunes on their Computer. Don't sync your iPod!
Try to restore the iPod, or try to put it as new iPod so it'll delete everything but you'll have your iPod problem fixed

Error code 265: The certificate chain was issued by an authority that is not trusted.

We are in the process of trying to set up a wireless network that uses NPS servers to authenticate domain users with computers that are not on our domain (BYOD).
We are using a valid, wildcard SSL (with intermediate certificates) to authenticate via PEAP. The certificate was issued by Godaddy.
When trying to connect, we are getting the authentication request.
The result of a connection attempt is no connection with an event log error code of - “265: The certificate chain was issued by an authority that is not trusted.”
We have tried ensuring that the certificates are in the correct containers on the respective NPS servers: “Certificates\Personal\Certificates” With the intermediate certificates located: “Certificates/Intermediate Certification Authorities”
All these attempts have proven fruitless. Any assistance or direction would be very much appreciated.

Hi,
Do you import the intermediate certificate in the right account? It should be imported in the Computer Account.
Have you imported the intermediate certificate in your client? Client need it to validate the certificate of your NPS server.
Here is a similar thread in which Greg has explained this issue in detail.
http://social.technet.microsoft.com/Forums/en-US/b770fcf6-d1e9-4aac-9005-62cb5ff6d485/the-certificate-chain-was-issued-by-an-authority-that-is-not-trusted?forum=winserverNAP
Hope this helps.
Steven Lee
TechNet Community Support

My macbook13in has a blue screen with error code 10813

my macbook 13in has a blue screen with error code 10813

Reinstalling OS X Without Erasing the Drive
Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Continue button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.
Also see:
Reinstall OS X Without Erasing the Drive
OS X Yosemite- Reinstall OS X
OS X Mavericks- Reinstall OS X
OS X Mountain Lion- Reinstall OS X
OS X Lion- Reinstall Mac OS X
Note: You will need an active Internet connection. I suggest using Ethernet
if possible because it is three times faster than wireless.

X301: Wireless error code 10

Similar Messages

Maybe you are looking for