Xfi Platinum and headset: Constant issues.

Ever since I installed my XFI plat. I've had no luck whatsoever enabling my headset to work. Albeit, it's not the greatest, most expensive headset to walk the earth, but at least with my old sound card, there were no issues. The headset is a Logitech headset I received when I purchased Battlefield 2, the exact make i don't know without phyisically looking at it. It has two plugs, a black and an orange one. I've tried virtually every combination I can think of, but am willing to accept suggestions, and nothing works. It's either a) an issue of me plugging it in incorrectly or b) it's muted somewhere through some option.
Any ideas?
Thanks-
Norton

Headsets or microphones with a USB connection cannot be connected to the input connections on a sound card directly. Instead, they must be connected to a USB port on a PC.
They are treated as a separate audio device by Windows. They will be listed as a separate audio device in Device Manager as well as in Windows Multimedia panel. To adjust the volume of the headset or the microphone, use Windows Volume Control.

Similar Messages

XFI Platinum and Windows 200

Hi there,
Im looking forward for a new XFI Platinum or Elite Pro but in the system requirements only appears windows XP; I have windows 2000 installed and dont wanna change to XP, has anybody an XFI soudcard working with Windows 2000? Is it working ok? Any kind of latency in sounds and recording audio or Midi?
Please write me to [email][email protected]][email protected][/url]
Thanks in advance

Headsets or microphones with a USB connection cannot be connected to the input connections on a sound card directly. Instead, they must be connected to a USB port on a PC.
They are treated as a separate audio device by Windows. They will be listed as a separate audio device in Device Manager as well as in Windows Multimedia panel. To adjust the volume of the headset or the microphone, use Windows Volume Control.

MSI K9A Platinum and VIA drivers issue? XP 0x0000007B stop error.

I get a Windows Stop error when trying to boot into Windows XP with new components. The SATA hard drive (and Windows XP installation) is from the old computer.
The new computer components are:
MB: MSI K9A Platinum, chipset: RD580 (North Bridge), SB600 (South Bridge)
CPU: AMD Athlon 64 x2 5600+, boxed (the cooler and fan came with the CPU).
Video: MSI Radeon 1950 XTX
The old (and working) computer setup is:
OS: XP Professional
MB: Abit AV8-3rd Eye, chipset: VIA K8T800Pro + VT8237
CPU: AMD Athlon 64 3500+
Video: Sapphire Radeon 9800Pro All-in-Wonder, videodriver: atidvag.dll version 6.14.10.6542
HD: Maxtor 6B200M0 SCSI Disk Device
BIOS: Phoenix 6.00PG 20.04.2005
System drivers with "via" in the name: VIAAGP1.SYS, viaide.sys, viasride.sys
VIA 4in1 (Hyperion) version: 4.55 (that can be found at HKEY_Local_Machine\Software\Via4in1Driver).
VIA 2.20e SATA/RAID driver was used when installing this computer setup.
The precise stop error is:
0x0000007B (0xba4c3528, 0xc0000034, 0x00000000, 0x00000000)
From many sites I have gathered that the error is related to Windows XP not being able to access a critical system drive. Most probably the SATA hard drive issue.
The problem probably is the VIA drivers of the old motherboard and/or the SATA driver.
First I should mention, that MSI K9A Platinum does not have a hard disk SATA driver. If it does, I have been unable to find one. Certainly no such floppy disk included, and no such driver in the MSI's Web page for this motherboard.
Second important point: I never used RAID. I did use VIA 2.20e SATA/RAID driver disk when installing Windows XP to the old computer.
Strange that the hard drive model is reported as a "SCSI Disk Device". It's not a SCSI drive however: it's a SATA disk.
I have tried to uninstal the motherboard chipset drivers (Hyperion v4.55), but there seems to be a bug here: the drivers should be uninstalled using the installation program, and select the uninstall option. However, I do not get the uninstallation option to choose at all! Yes, I'm using the normal installation mode, not the quick installation (although tried that, too). The Hyperion setup program just installs, and asks to reboot the computer. After rebooting and trying again, it still does not offer me an uninstallation choise.
I know how to install hard drive VIA SATA driver, but I have no idea how to uninstall it. And I'm afraid to do that without certainty that it IS the solution, since I could not access the hard drive any more in the old computer setup (and return to read this forum). Also, I do not have a floppy drive any more. Anyone know if there is an issue with K9A and XP having VIA SATA driver installed?
When I tried the new computer setup, I first tried the simplest possible hardware combination: there were no CD/DVD-drives, no (parallel)IDE hard drives, and no PCI cards, except the MSI video adapter.
My BIOS Setup experiments. None of these helped: got the same stop error each time.
1) I didn't much touch the BIOS setting first. Just tried to boot with the settings BIOS came with.
2) Next I disabled the integrated audio, LAN and IEE1394 devices and floppy drive and disabled all other choises except the SATA drive as a boot device.
3) Next I tried with the fail-safe BIOS defaults.
4) Cleared CMOS.
5) Changed OnChip SATA type from Native IDE to Legacy IDE. (Only one boot attempt with the setting as Legacy.)
6) Disabled PCI IDE BusMaster.
7) Never touched anything in the Cell Menu: so the settings are in minimum.
A step I have taken after the last attempt: run Windows XP hard drive error-checking tool to every logical drive with the fix option selected, and the system drive also with scan the bad sectors option selected.
My plans next are:
1) to install a newer Hyperion driver. If that would correct the no-unistallation-choice-bug,
2) to disable USB-devices in the BIOS (desperate),
3) to choose the Windows general video display driver (although I seriously doubt this is a display driver problem!).
4) to uninstall the Anti-Virus software (Avira Antivir).
I've read a numerous Web pages so far about the 0x0000007B stop error. Here are some links:
Quote
http://www.seagate.com/www/en-us/support/knowledge_base/
Stop 0x0000007B or INACCESSIBLE_BOOT_DEVICE
This Stop message, also known as Stop 0x7B, indicates that Windows XP Professional lost access to the system volume or boot volume during the startup process. This error always occurs while the system is starting and is often caused by one of the following:
* Hardware problems
* Corrupted or incompatible storage drivers
* File system problems
* Boot sector viruses
* Outdated firmware
During I/O system initialization, this error can occur when:
* The controller or driver for the startup device (typically the hard disk) failed to initialize the necessary hardware.
* File system initialization failed because the system did not recognize the data on the boot device.
Quote
http://support.microsoft.com/kb/314082
You receive a Stop 0x0000007B error after you move the Windows XP system disk to another computer
SYMPTOMS
After you move the Microsoft Windows XP system (boot) disk to a backup computer, you may receive the following Stop error when you try to start the Windows XP-based backup computer:
STOP: 0x0000007B (0xF741B84C,0xC0000034,0x00000000,0x00000000)
CAUSE
This error may occur if the registry entries and the drivers for the mass storage controller hardware in the backup computer are not installed in Windows XP.
RESOLUTION
To resolve this error, use the same hardware for the backup computer.
Heh, heh! Very nice Microsoft, but I plan to update my computer, so I NEED to use different components
Quote
http://support.microsoft.com/kb/324103
Device Driver Issues
You may receive a "Stop 0x0000007B" error message in the following scenarios:
•   A device driver that the computer boot controller needs is not configured to start during the startup process.
•   A device driver that the computer boot controller needs is corrupted.
•   Information in the Windows XP registry (information related to how the device drivers load during startup) is corrupted.
Hardware Issues
You may receive a "Stop 0x0000007B" error message if there is a resource conflict between the boot controller and another controller or between SCSI devices. You may also receive this Stop error message if drive translation is not being performed or if drive translation was changed. To troubleshoot this issue:
1.   If an IRQ or I/O port address conflict exists between the boot controller and another controller, Windows XP either stops responding (hangs) or displays a "Stop 0x0000007B" error message. If you recently added new hardware, remove the new hardware or reconfigure it so that it does not conflict with the resources of any other installed controllers.
2.   If you are using a SCSI hard disk, check the SCSI chain for correct termination. Remove any unused SCSI devices or make sure that each SCSI ID is unique.
3.   Make sure that drive translation is turned on (if it is required) and that it has not been changed. For example, if you recently switched controllers, this issue may occur. For additional information about this issue, click the following article number to view the article in the Microsoft Knowledge Base: 314082.
Quote
http://support.microsoft.com/kb/316401/
SYMPTOMS
When you start your Microsoft Windows XP-based computer after you replace the motherboard on the computer, you may receive a Stop error message that is similar to the following:
STOP 0x0000007B INACCESSABLE_BOOT_DEVICE
CAUSE
This issue may occur if the new motherboard contains an embedded IDE controller that has a different chipset than the original motherboard.
RESOLUTION
Method 1: Perform an in-place upgrade of Windows XP [<- That means repair installation of Windows XP]
•   Do not use a repair or in-place upgrade if you suspect disk problems.
Method 2: Repartition and format your hard disk and reinstall Windows XP

Alright I got the situation over.
Quote from: Roskaposti on 19-May-07, 04:44:59
My plans next are:
1) to install a newer Hyperion driver. If that would correct the no-unistallation-choice-bug,
2) to disable USB-devices in the BIOS (desperate),
3) to choose the Windows general video display driver (although I seriously doubt this is a display driver problem!).
4) to uninstall the Anti-Virus software (Avira Antivir).
I did try all all the above, and none of them helped.
And by the way: after installing the new Hyperion (VIA chipset drivers), I was finally able to also uninstall. It also uninstalled the IDE SATA (I think) and PATA drivers.
But what I had to do, was to make a REPAIR installation of Windows XP.
So, I was wondering now afterwards: this is really, really silly. Why the hell we need to re-install Windows if we move the SYSTEM SATA drive to another computer? We don't have similar problem with parallel IDE drives. Whom should we thank here??
The issue is to insert the driver files and the information of the ide drivers Windows should use with the next boot. How can it be this difficult?
What you basically need is..
- the information about the new chipset's PCIIDE.SYS/[VENDOR_PROVIDED_FILE].SYS and ATAPIIDE.SYS inserted into the values in HKEY_LOCAL_MACHINE\SYSTEM\ControlSetXXX\Control\CriticalDeviceDatabase
- and the vendor's IDE drivers to the %SYSTEMROOT%/System32/drivers folder.
Maybe something else, I don't know. But the problem was, Windows didn't know how, or what drivers to use. That can't be so big problem you need to install the whole OS anew!

MOVED: K9A Platinum and Vista 64 issues

This topic has been moved to Vista problems.
https://forum-en.msi.com/index.php?topic=109584.0

Quote from: Paul B on 20-March-08, 23:05:39
Hi all,
Ok so I said I'd report back once all working and here i am (touches wood )
So my system is now Phenom less, I'm a bit gutted it's going back for RMA for refund. I have in the mean time replaced it with an x2 5000+ BE.
So just a recap on my spec
K9a2 Platinum
x2 5000+ BE Running stock 2.6Ghz
8GB OCZ DDR2 800 Platinum
2 x 3870x2 in crossfire X mode.
Windows Vista x64 OEM
This OS now installed no issues no BSOD for secondary clock interrupt. But i did have issues installing it on the Promise raid array. Though it was the old more than 2GB ram thing so did the install with one stick and then Patch vista install the other 6GB but no still got system rebooting after the progress bar 9 times out of 10.
So i have the HDDs on the standard SB600 sata ports as individual drives, installed x64 all 8GB still installed. Not knowing yet if it was driver related I let vista install all the drivers, the only other driver my system needed were the cat 8.3s and I only installed the graphics driver and CCC not the IDE or north bridge filter as the system is using vistas default drivers.
I have installed all updates and everything seems rock solid. (touches more wood!!) I have spent the last week relentlessly trying to get this OS installed, but hey I learnt a few things along the way..
Paul
But now it is and I have my 8GB and crossfire X I'm happy and when the good Phenoms arrive I'll get one but I'll read all the reviews on the web first....
Hi,
Right then resurecting an oldish thread, I have just purchased a Phenom 9750 and installed with the new 1.4 bios, and all is well. The same Vista x64 install is rock solid and damn quick now.
Buy the B3 Phenoms with confidence they (AMD) have pulled back some ground and in my case some confidence.
Paul

Xfi platinum and vi

Hi guys, Just wanted to know if anyone can help me with a x-fi vista issue, bought this card and vista same time and was told that it is vista capable....it is but not very capable..lol. i installed it orriginally on xp pro and was super impressed. Now i have that dull feeling!!! great soundcard but no features for vista. Any ideas how i can get the consoll i used with xp it was devine. i have no effects on vista att all.. not even a touch of reverb or anything else?

go the sales and order the Vista Installation disk its free except the famous S/H fee You might be able to find it on this site Check old threads go to http://us.creative.com/shop/shopcate...p category=209& look for the vista installation disk good Luck

P35 Platinum and Vista/ACPI issue

I'm having problems trying to get Vista installed on my P35 Platinum-based system. I'm getting an error at the beginning of Vista's installation that the BIOS doesn't support ACPI. Well, that option is turned on in the BIOS, and I've toggled just about every setting under the Power Management section of the BIOS config utility, but nothing makes a difference. I flashed the latest (1.2) BIOS to the board, no change. I'm also seeing the computer go to a 'Safe to turn off your computer' screen rather than it just powering off - is this related?
Any suggestions would be appreciated, thanks.

ACPI has to be enabled before you install XP. If you re-enable it after installing XP, you will get a bluescreen. If you used an existing Windows Installation, that was set up under different system conditions, it probably didn't have the proper HAL drivers for the new configuration.
If you re-install XP with ACPI, IOAPIC and MPS Table = 1.4 you shouldn't have any problems.
--> http://support.microsoft.com/?scid=kb%3Ben-us%3B309283&x=12&y=12
Quote
Device Manager does not permit the change from a Non-ACPI HAL to an ACPI HAL. You must use a new install of Windows XP or Windows Server 2003 for this kind of change. Change from an ACPI HAL to a Non-ACPI HAL only for troubleshooting purposes.

XFI Platinum mic issue

Hi I recently purchased a XFI pLatinum sound card for my custom built computer that i just made like a month ago...and i cant seem to get the mic to work on my AHS55 altec lansing headset or anyother headset that i have tried. I use it on teamspeak client II and all of my friends say that they cant here me but ts says that there is nothing wrong with mic. I have it plugged into i believe is mic2/line2 (the front dri've panel) and i have tried the back but when i go to test it doesn't recoginize that i am even talking when i test just sitts there not getting any sound at all...also i can hear myself talk like the mic is echoing or something like that...
cpu: amd x2 4600+
sound card: xfi platinum
vga: 256mb bfg 7900gt oc
mem: corsiar ddr2 xms2 2gb (6400)
mobo: gigabyte ga-m59sli-s5

Yes, the power goes directly into the rack (2 in the picture), otherwise it doesn't work. [img"]http://img382.imageshack.us/img382/7563/iodri'vetw4.jpg">

X-fi extremegamer and 5.1 headset, static issues

0X-fi extremegamer and 5. headset, static issues? Hi,
? Ive had this issue for about a year now and havent acted on it. I have a x-fi extremegamer and a LTB ac97 5. headset. I am running the latest driver for my x-fi. The issue is, whenever there is a loud sound or even if the master volume is turned up to high I get this horrible static sound. I can happen for a windows sound or explosions in a game or movie. An example of how it sounds is like (an example of an explosion in a game).....BO(PSSSSSSSSSSHHHHHHHHHHHHHH). I have tried a new amp for my headset. I have sat for hours trying to find the cause. Of course the lower the volume the less likely the chance of the sound. ?I called LTB tech support and the tech said it may be that the x-fi is overdriving the speakers. Would there be a setting that would help me out. Could it be my x-fi card is shot? It happens in both xp sp3 and Vista Ultimate 32bit. Here's my rig specs.
Abit At8
AMD Athlon x2 4600
4gb gskill ddr 3200
ATI Radeon 4850
320gb sata hd
Creative X-fi extremegamer
Dual boot XP sp3 and Vista Ultimate 32
Thanks for the help.
J

lagagnon wrote:Try this?: http://ubuntuforums.org/showpost.php?p= … tcount=432
That post is totally missing the point. It directs stereo to all 6 speakers, which works with any soundcard.
The point is, ALSA can't use the other 4 speakers, with this particular soundcard, because the configuration required is Creative's secret and hasn't been discovered yet.

Vista x64 / Logitech Orbit MP / XFi Platinum problem confirmed... PLEASE RE

I was wondering why my 7. option disappeared from my speakers configuration option. Turns out another person had the same issue with his computer and found out that unplugging his Orbit MP fixed the problem. (It was limiting his sound to 5.) Well I had the same configuration but took it a step further to disable the Logitech Orbit recording device in device manager.Problem solved! Im not sure if this is a Vista, a CL, or Logitech problem. I figure I'd throw this out there to let everyone know. Problem reproduced with: XFi Platinum w/ optical out going to external receiver 7.Logitech .5 Quickcam DriversXFi 2_5_0004 drivers (the newest ones) Would like to hear everyone else's comments on this. Thanks.

It's funny how some people say you can enable 5. with vista 64 using alchemy but for 10 days now I have yet to get a response.

XFi Platinum - can't get the rack to w

Hello,just bought the Xfi platinum fatalty and although the card works fine, the nternal rack does not do anything. my configuration:OS: win XP 32 bitsMB: P5B Deluxe - Core 2 Duo 6600 - 3 GB RAM?my installation:i plugged the large flat cable into the card and the rack; plugged power into the card.. symptoms:No headset sound?(i did?tick the headsets?box?in the console), the remote does not work;, and there is no light on the rack (should there be a light? since there is one on the card itself maybe tehre is one on the rack as well)?what I have tried so far:remove setpoint SW since i have wireless keyboard and mouse and in this form there was a thread on?external rack and setpoint incompability... did not change anything though (I ahve the internal rack... I have tried in case nevertheless)?thanks for helping...

Yes, the power goes directly into the rack (2 in the picture), otherwise it doesn't work. [img"]http://img382.imageshack.us/img382/7563/iodri'vetw4.jpg">

How do I use a NORMAL headset (dual 3.5mm) on my new Macbook pro retina? No usb ports available and headset buddy adapter doesn't work.

Title says it all:
How do I use a NORMAL headset (dual 3.5mm) on my new Macbook pro retina? No usb ports available and headset buddy adapter doesn't work.

Hi Auracles1,
Here's a pretty discussion regarding wireless printing with this device and a Mac.
http://h30434.www3.hp.com/t5/Printer-networking-and-wireless/HP-Officejet-6500-E 709n-wireless-issue/m-p/258853
I have a similar OfficeJet and it was a multi-step process. (1) Install printer drivers on the machine, (2) Add the printer queue in print & fax, (3) Run the "setup wizard" from the disc for wireless printing.

P965 Platinum and E6600 won't go to 3GHz

Hello,
I have a MSI P965 Platinum and a E6600. Currently I have two sticks of Corsair Value Select 1GB PC-5300 RAM, rated at 667Mhz 5-5-5-15.
The E6600's stock is 2.4GHz, and I want to go to 3GHz. This should be dead simple - not only can the E6600 usually clock much higher, but 3GHz will only require a 333Mhz FSB (9 x 333), which means my RAM doesn't have to be overclocked at all since it is rated for 667MHz DDR2. I should be able to obtain 3GHz with a nice comfortable 1:1 FSB:RAM ratio without stressing the Corsair Value ram beyond specifications.
However, it just won't work. I seem to be having RAM instabilities at 667MHz 5-5-5-15 and 333Mhz FSB. The reason I say RAM is because Memtest86 freezes, and SuperPi has a 'not exact in round' error in 16M and 32M - which apparently means there is a problem with memory stability. Now, I know this sounds like the RAM is faulty, but I don't think it is, because when I run stock 266MHz FSB, the system is fine at 4:5 divider to make the RAM 667Mhz. It's only when I increase the FSB (and not the RAM at all) does the system become unstable. At 266MHz FSB and 667MHz RAM, my system will pass any stress test, but not at 333Mhz FSB and 667Mhz RAM.
I've upped the CPU voltage 3 notches to around 1.350 or so under load. My ram is at 1.9v, although I tried 1.95v too. I didn't touch the chipset voltage (should I?). My temperatures seem ok - I'm only using the stock Intel cooler, but it should be able to handle 3GHz fine. It hovers around 48c idle, 60c load according to Everest Ultimate (before it crashes in SuperPi), so it doesn't appear to be overheating while overclocked. Not great tempts but acceptable.
However, there are two things I've noticed:
- In the BIOS, if I select CAS to be 5 or 6, CPUZ still reports my ram at CAS3 (which my RAM can't do at 667Mhz), or 3-5-5-15. However if I select CAS4, it reports CAS4 properly (still unstable though), or 4-5-5-15. This is only a problem when I overclock the FSB - at stock FSB, the CAS timings are reported correctly. It could be an issue with CPUZ, but I doubt it. If there is a bug with the P965 Platinum not setting the CAS right when overclocking, this might explain why I'm having RAM stability issues even though I'm not overclocking the RAM - i.e. because the board is not using the right CAS setting. Is this a known bug? Also, I tried Auto SPD but it tried to use 4-4-4-12 at 667MHz (again, which this RAM won't do).
- When I run 333Mhz FSB and 667MHz RAM, the POST shows some sort of error message about the board not supporting CPU's with a 267Mhz FSB or something (which is weird, because 266Mhz is the stock speed *shrug*), and that it's resetting it. Sorry I can't recall the exact error off hand, but I can try the overclock again and provide it later on if needed. Anyway, despite the error message, the overclock still applies - it will boot into Vista 64-bit at 3Ghz, it just won't pass any stress test.
Is it possible a BIOS update could help me? I run V1.4, and even though I know there is a V1.8 now, no newer version mentions anything about fixing overclocking issues. I don't like to update my BIOS unless necessary (and I don't even have a floppy drive anyway, would need to figure out how to do it via USB).
Thanks for any help. I'm certain my RAM isn't faulty and I'm certain my CPU should be able to reach 3Ghz surely. I'm also pretty sure heat isn't an issue. I think maybe the board is trying to force CAS3 when FSB overclocking or something? That's my guess anyway.

Thanks for the reply!
Sorry, I should have mentioned I was definitely achieving 1:1 - I recall the confusion over why my RAM was trying to be 800+MHz at 667 and then I realized 533 actually meant 1:1, 667 4:5 etc, so I am definitely running at 533/1:1. I doubt this RAM would even post at 800+ MHz.
So updating the BIOS may help? Ok thanks, I guess I will update then. I don't see it in the "fix" list though on the site. Is there a way I can get a *full* fix/enhancement list for 1.5, 1.6, 1.7 and 1.8 so I know exactly what I'm fixing going from 1.4 to 1.8?
Also, does MSI support LiveUpdate BIOS in Windows Vista 64 yet? And if not, is there an official way to update via a USB stick? (no FDD here).

Audigy 2 ZS Platinum and Stereo PCM

#Audigy 2 ZS Platinum and Stereo PCM? Hi,
Have an Audigy 2 ZS Platinum here and I'm having issues with having no audio when inputting Stereo PCM over Optical Toslink. I tried using both default and internal decoder, but no audio at all. It only works when using passthru/bypass mode. Tried a bunch of stereo inputs and had no audio at all. Is Stereo PCM not supported or what here? The test input streams were PCM two channel 48khz 6bit and 20bit. And Dolby Pro Logic is listed in the decoder tab with Auto, On, or Off. But maybe that isn't the same as Dolby Pro Logic II and that is why there is no audio. Only seems to work with Passthru mode only.
Message Edited by Seraphic on 04-7-2009 03:07 PMMessage Edited by Seraphic on 04-8-2009 0:44 PM

Hi, is anyone able to offe some help? Thanks

Bridge CC and the constant thumbnail regeneration problem.

I'm one of many who suffers from Bridge CC constantly regenerating thumbnails. There are multiple threads about the problem, with different descriptions and different theories of the cause.
I recently tried an experiment. I replaced Camera Raw.8bi (version 8) file in the CC folder with the Camera Raw.8bi file from my old CS6 folder (version 7.1.0.354). That worked OK. Bridge CC and Photoshop CC work with the older version of Camera Raw, and the constant regeneration of thumbnails ceased.
Unfortunately, installing the old version of Camera Raw causes Bridge CC to regenerate thumbnails for all folders on the first visit, even though the files are cached and unchanged. But after that first visit, no regeneration occurs.
I have no idea why that is, but I think the experiment gives good evidence that the problem lies in the Camera Raw code and not in the Bridge CC code itself.
None of the various threads I've seen give me any confidence that Adobe has acknowledged this problem, or is even aware of it. And I'm not sure of the best way to get their attention. I've seen references that say Adobe bug reporting should be done on the photoshop.com website. I've tried that in the far past for different issues, but with no success. However, with no known alternative, I've made the following post:
http://feedback.photoshop.com/photoshop_family/topics/bridge_cc_re_caching_thumbnails?rfm= 1
I encourage others to "reply" to that post. Maybe if enough people respond, Adobe will notice and acknowledge.
If anybody knows a better way to report bugs (and get acknowledgement), please share.

Been there, done that:
http://feedback.photoshop.com/photoshop_family/topics/unneccesary_bridge_thumbnail_and_pre view_extraction
They know about it, they just don't know how to recreate it.
Best thing we can do is reliably recreate the fault. My workaround is to only enable Lens Profile Corrections when necessary, as it is a combination of that and some other factor(s) which seems to trigger it.
If you read all the discussions, you'll see that there are two bugs which produce the same symptoms. One introduced in probably ACR 6.1, whichg was fixed in 8.2; and the other was introduced in 7.3 and is ongoing.

Problem with XFI platinum fatal1ty sound from panel but not from c

Hi
I just got an XFI platinum fatalty card with front panel, I have only been able to get sound out of the ports on the acctuall card for about 3 minutes then it screetched and went off. Since then the most I can get is an EXTREEMLY quiet (I need to turn up my speakers and the card volume to full) and distorted sound from my center and rear left speaker (5. set). However the wierd thing is when I plug in the headphones into the front panel it works perfectly, the thing is if i switch it back to speakers i have to restert before the headphones will work again.
I have tried to update the drivers but there are no newer ones, I figure I have it seated correctly or I would have no sound from the panel, I just dont know what to do.
its plugged into a Asus Crosshair nForce 590 SLI AM2 Motherboard, I have tried it in 2 different PCI slots and nothing changes, I'm running XP.
Help please, it would be much appreciated, I went through hell to get this card deli'vered and not its not working properly!!!
Any ideas?Message Edited by C4TS on -09-20072:42 AM

Is there anybody with any idea what the problem might be?

Xfi Platinum and headset: Constant issues.

Similar Messages

Maybe you are looking for