XI QoS
Hi,
I am running a XI scenario where I have an IDOC to XML conversion and in this I want the XML data to pass through only one queue in the SCM system but it somehow goes through 2 queues.Is there a way where I cn maintain the QoS so that this data would pass through a single queue.
Thanks & Regards,
Arun
Hi Arun,
This link should give you the info you require:
http://help.sap.com/saphelp_nw04/helpdata/en/41/b714fe5ffc11d5b3ea0050da403d6a/frameset.htm
http://help.sap.com/saphelp_nw04/helpdata/en/7b/94553b4d53273de10000000a114084/content.htm
Hope this helps!.
Cheers,
Chandra
Similar Messages
-
Question Regarding QoS and Firewalls Rules
Hello experts, I hope a simple question for you today. I am working to elevate our outdated H323 traffic down a VPN tunnel we are only getting 600k throughput on.
Under "Networking --> QOS --> WAN QOS" I have configured the downstream and upstream bandwidth rates using the 85% rule. I have also created a bandwidth profile called VOIP using 128-256kbps with a priority of "High"
Under "Traffic Selector" I have created the profile using the VLAN 100 for the IP phones with the VOIP bandwidth profile.
My question, is this the correct configuration and I'm done? Or do I need to go further and create the same IPv4 rules in the firewall rules giving it a QoS Priority of "Minimize Delay"
Is there a way in SA540 to see the QOS statistics to see if they are working correctly? I appreciate your input as always experts!!It's about the relevance of the link. Some will post a vague link to the SAP help that adds no value to anyone trying to find the answer to the question, whereas a targeted link to a - possibly difficult to find - page can be very useful.
It's a bit of a subjective thing, example:
A detailed question asks about technical info behind assigning a cost center to an organizational unit in the org chart.
A reply such as:
Check [this link|http://help.sap.com/saphelp_erp60_sp/helpdata/en/0b/dfba3692dc635ce10000009b38f839/frameset.htm].
Is just wasting everyone's time. Unfortunately we see a lot of these, people seem to think it's a quick way of getting cheap points but it just frustrates everyone else.
Asimilar answer can however be very useful if it contains a targeted link that relates directly to the question, e.g.
See the help on [account assignment infotypes|http://help.sap.com/saphelp_erp60_sp/helpdata/en/bb/bdb2b6575911d189240000e8323d3a/frameset.htm].
However a generic link as per my first example as part of a detailed explanation with a comment of "further info can be found over here" is a good post since the purpose of the link it more for convenience or reference info in addition to the answer in the post.
Hope that helps,
Mike -
Cisco Jabber Client - QoS Config
Hi Guys,
I'll be deploying the new jabber client for a customer and i'm unsure of what QoS to configure on the switch ports for end users. Users will also have 7942 handsets, so if i configure auto qos voip cisco-phone, I doubt this will protect the voice/video for Jabber.
Has anyone got any config or tips they can share?
Cheers,
JamesHi,
I believe you can use "auto qos voip cisco-softphone"
Please see below QOS SRND.
http://www.cisco.com/univercd/cc/td/doc/solution/esm/qossrnd.pdf
Regards
Ronak -
Cisco 7206 has with LLQ QOS and cpu 85 %
hi all ,
i want to mention issue about cisco router 7206 npeg2 :
can this router handle traffic 780 Mbps as download and 75 MBps as upload ?? with cpu 85 % and with LLQ qos ??
im asking this question because my QOS althoug it matched alot of traffic , it some time get slow and seems that QOS not working fine , im sure that my work is fine, because it was fine , but recent days i added more bw ???!!!!!
dont know if need more memory for router for QOS :
===============================================================
7200Gateway#sh memory
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor 6B97A80 1883669308 114125456 1769543852 1768174580 1760364316
I/O 78000000 67108864 4482572 62626292 62598896 62617884
Transient 77000000 16777216 22196 16755020 16222412 16728368
Processor memory
Address Bytes Prev Next Ref PrevF NextF Alloc PC what
06B97A80 0000010004 00000000 06B9A1C4 001 -------- -------- 01A493D8 CEF: fib
06B9A1C4 0000000028 06B97A80 06B9A210 000 87F3D04 87FD620 015FC24C AAA Attr Binary/String
06B9A210 0000004700 06B9A1C4 06B9B49C 001 -------- -------- 01AC85B4 ADJ: adjacency
06B9B49C 0000004100 06B9A210 06B9C4D0 001 -------- -------- 0011245C HTTP CORE
06B9C4D0 0000004100 06B9B49C 06B9D504 001 -------- -------- 00112548 HTTP CORE
06B9D504 0000004100 06B9C4D0 06B9E538 001 -------- -------- 00112548 HTTP CORE
06B9E538 0000004100 06B9D504 06B9F56C 001 -------- -------- 00112548 HTTP CORE
06B9F56C 0000004100 06B9E538 06BA05A0 001 -------- -------- 00112548 HTTP CORE
06BA05A0 0000000756 06B9F56C 06BA08C4 001 -------- -------- 0343C38C Process
06BA08C4 0000000204 06BA05A0 06BA09C0 001 -------- -------- 0343FAB4 Process Events
06BA09C0 0000022764 06BA08C4 06BA62DC 001 -------- -------- 04055CB4 IPSM Octet Str
06BA62DC 0000014488 06BA09C0 06BA9BA4 001 -------- -------- 0405C0C4 ipsm IPSEC Fai
06BA9BA4 0000004100 06BA62DC 06BAABD8 001 -------- -------- 00112548 H
===========================================================================
==========================================
7200Gateway#sh version
Cisco IOS Software, 7200 Software (C7200P-ADVENTERPRISEK9-M), Version 12.4(24)T7, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 28-Feb-12 12:53 by prod_rel_team
ROM: System Bootstrap, Version 12.4(12.2r)T, RELEASE SOFTWARE (fc1)
7200Gateway uptime is 2 weeks, 5 days, 19 hours, 43 minutes
System returned to ROM by power-on
System image file is "disk2:/c7200p-adventerprisek9-mz.124-24.T7.bin"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
Cisco 7206VXR (NPE-G2) processor (revision A) with 1966080K/65536K bytes of memory.
Processor board ID 13252317
MPC7448 CPU at 1666Mhz, Implementation 0, Rev 2.2
6 slot VXR midplane, Version 2.0
Last reset from power-on
PCI bus mb1 (Slots 1, 3 and 5) has a capacity of 600 bandwidth points.
Current configuration on bus mb1 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
PCI bus mb2 (Slots 2, 4 and 6) has a capacity of 600 bandwidth points.
Current configuration on bus mb2 has a total of 0 bandwidth points.
This configuration is within the PCI bus capacity and is supported.
Please refer to the following document "Cisco 7200 Series Port Adaptor
Hardware Configuration Guidelines" on Cisco.com <http://www.cisco.com>
for c7200 bandwidth points oversubscription and usage guidelines.
1 FastEthernet interface
3 Gigabit Ethernet interfaces
2045K bytes of NVRAM.
250880K bytes of ATA PCMCIA card at slot 2 (Sector size 512 bytes).
65536K bytes of Flash internal SIMM (Sector size 512K).
Configuration register is 0x2102
==============================================================
7200Gateway#sh processes cpu
CPU utilization for five seconds: 85%/84%; one minute: 84%; five minutes: 84%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 32 416 76 0.00% 0.00% 0.00% 0 Chunk Manager
2 32788 342520 95 0.00% 0.05% 0.05% 0 Load Meter
3 0 1 0 0.00% 0.00% 0.00% 0 chkpt message ha
4 0 1 0 0.00% 0.00% 0.00% 0 EDDRI_MAIN
5 2624584 213262 12306 0.00% 0.03% 0.04% 0 Check heaps
6 56 373 150 0.00% 0.00% 0.00% 0 Pool Manager
7 0 2 0 0.00% 0.00% 0.00% 0 Timers
8 0 2 0 0.00% 0.00% 0.00% 0 ATM AutoVC Perio
9 0 2 0 0.00% 0.00% 0.00% 0 ATM VC Auto Crea
10 16 28543 0 0.00% 0.00% 0.00% 0 IPC Dynamic Cach
11 0 1 0 0.00% 0.00% 0.00% 0 IPC Zone Manager
12 688 1670887 0 0.00% 0.00% 0.00% 0 IPC Periodic Tim
13 520 1670887 0 0.00% 0.00% 0.00% 0 IPC Deferred Por
14 0 1 0 0.00% 0.00% 0.00% 0 IPC Seat Manager
15 0 1 0 0.00% 0.00% 0.00% 0 IPC BackPressure
16 9007072 30711869 293 1.35% 0.15% 0.11% 0 EnvMon
17 0 1 0 0.00% 0.00% 0.00% 0 OIR Handler
18 0 1 0 0.00% 0.00% 0.00% 0 Crash writer
19 1380 3892 354 0.00% 0.00% 0.00% 0 ARP Input
20 1584 1784473 0 0.00% 0.00% 0.00% 0 ARP Background
21 0 2 0 0.00% 0.00% 0.00% 0 ATM Idle Timer
22 0 1 0 0.00% 0.00% 0.00% 0 CEF MIB API
23 4 134 29 0.00% 0.00% 0.00% 0 AAA high-capacit
24 0 1 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
25 0 1 0 0.00% 0.00% 0.00% 0 Policy Manager
26 0 2 0 0.00% 0.00% 0.00% 0 DDR Timers
27 0 5 0 0.00% 0.00% 0.00% 0 Entity MIB API
28 0 2 0 0.00% 0.00% 0.00% 0 Serial Backgroun
29 0 1 0 0.00% 0.00% 0.00% 0 RO Notify Timers
30 0 1 0 0.00% 0.00% 0.00% 0 RMI RM Notify Wa
31 28 281 99 0.00% 0.00% 0.00% 0 EEM ED Syslog
32 0 2 0 0.00% 0.00% 0.00% 0 SMART
33 724 1712571 0 0.00% 0.00% 0.00% 0 GraphIt
34 0 2 0 0.00% 0.00% 0.00% 0 Dialer event
35 0 1 0 0.00% 0.00% 0.00% 0 SERIAL A'detect
36 0 2 0 0.00% 0.00% 0.00% 0 XML Proxy Client
37 0 2 0 0.00% 0.00% 0.00% 0 VSA background
38 0 1 0 0.00% 0.00% 0.00% 0 VSA Cleanup Proc
39 0 1 0 0.00% 0.00% 0.00% 0 Critical Bkgnd
40 4348 444483 9 0.00% 0.00% 0.00% 0 Net Background
41 0 2 0 0.00% 0.00% 0.00% 0 IDB Work
42 32 501 63 0.00% 0.00% 0.00% 0 Logger
43 1236 1710802 0 0.00% 0.00% 0.00% 0 TTY Background
44 16504 1712627 9 0.07% 0.00% 0.00% 0 Per-Second Jobs
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
45 20 34 588 0.00% 0.00% 0.00% 0 IF-MGR control p
46 8 40 200 0.00% 0.00% 0.00% 0 IF-MGR event pro
47 0 1 0 0.00% 0.00% 0.00% 0 Inode Table Dest
48 0 1 0 0.00% 0.00% 0.00% 0 IKE HA Mgr
49 0 1 0 0.00% 0.00% 0.00% 0 IPSEC HA Mgr
50 4 4 1000 0.00% 0.00% 0.00% 0 rf task
51 12808 179149 71 0.00% 0.00% 0.00% 0 Net Input
52 1304 342532 3 0.00% 0.00% 0.00% 0 Compute load avg
53 610136 28974 21058 0.00% 0.00% 0.00% 0 Per-minute Jobs
54 0 1 0 0.00% 0.00% 0.00% 0 Token Daemon
55 4 10570 0 0.00% 0.00% 0.00% 0 Transport Port A
56 1272 505453 2 0.00% 0.00% 0.00% 0 HC Counter Timer
57 0 1 0 0.00% 0.00% 0.00% 0 Coproc Event Pro
58 0 1 0 0.00% 0.00% 0.00% 0 POS APS Event Pr
59 0 1 0 0.00% 0.00% 0.00% 0 SONET alarm time
60 0 1 0 0.00% 0.00% 0.00% 0 CSP Timer
61 204 4 51000 0.00% 0.00% 0.00% 0 USB Startup
62 0 2 0 0.00% 0.00% 0.00% 0 FPD Management P
63 0 1 0 0.00% 0.00% 0.00% 0 FPD Action Proce
64 0 2 0 0.00% 0.00% 0.00% 0 VNM DSPRM MAIN
65 0 1 0 0.00% 0.00% 0.00% 0 RF_INTERDEV_DELA
66 0 1 0 0.00% 0.00% 0.00% 0 RF_INTERDEV_SCTP
67 464 1712577 0 0.00% 0.00% 0.00% 0 ISA Common Helpe
68 0 2 0 0.00% 0.00% 0.00% 0 Flash MIB Update
69 0 58 0 0.00% 0.00% 0.00% 0 Flash Card Oir
70 0 1 0 0.00% 0.00% 0.00% 0 CES Line Conditi
71 0 1 0 0.00% 0.00% 0.00% 0 CF_INTERDEV_SCTP
72 0 1 0 0.00% 0.00% 0.00% 0 Async write proc
73 0 2 0 0.00% 0.00% 0.00% 0 Ethernet CFM
74 736 1670893 0 0.00% 0.00% 0.00% 0 Ethernet Timer C
75 0 1 0 0.00% 0.00% 0.00% 0 delayed evt hand
76 28 112 250 0.00% 0.00% 0.00% 0 AAA Server
77 0 1 0 0.00% 0.00% 0.00% 0 AAA ACCT Proc
78 0 1 0 0.00% 0.00% 0.00% 0 ACCT Periodic Pr
79 0 2 0 0.00% 0.00% 0.00% 0 AAA Dictionary R
80 744 1670882 0 0.00% 0.00% 0.00% 0 BGP Scheduler
81 0 2 0 0.00% 0.00% 0.00% 0 Ethernet OAM Pro
82 0 2 0 0.00% 0.00% 0.00% 0 Ethernet LMI
83 0 2 0 0.00% 0.00% 0.00% 0 CEF switching ba
84 3684 14726 250 0.00% 0.00% 0.00% 0 ADJ resolve proc
85 8 30 266 0.00% 0.00% 0.00% 0 IP ARP Adjacency
86 0 1 0 0.00% 0.00% 0.00% 0 IP ARP Retry Age
87 3481296 6804010 511 0.00% 0.02% 0.01% 0 IP Input
88 0 1 0 0.00% 0.00% 0.00% 0 ICMP event handl
89 0 9 0 0.00% 0.00% 0.00% 0 TurboACL
90 0 2 0 0.00% 0.00% 0.00% 0 TurboACL chunk
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
91 0 1 0 0.00% 0.00% 0.00% 0 IPv6 Echo event
92 16 2854 5 0.00% 0.00% 0.00% 0 MOP Protocols
93 0 1 0 0.00% 0.00% 0.00% 0 LSP Tunnel FRR
94 0 1 0 0.00% 0.00% 0.00% 0 MPLS Auto-Tunnel
95 0 3 0 0.00% 0.00% 0.00% 0 PPP Hooks
96 0 1 0 0.00% 0.00% 0.00% 0 Async write proc
97 0 1 0 0.00% 0.00% 0.00% 0 SSS Manager
98 0 1 0 0.00% 0.00% 0.00% 0 SSS Feature Mana
99 0 1 0 0.00% 0.00% 0.00% 0 SSS Feature Time
100 0 2 0 0.00% 0.00% 0.00% 0 Spanning Tree
101 0 1 0 0.00% 0.00% 0.00% 0 X.25 Encaps Mana
102 20 96 208 0.00% 0.00% 0.00% 0 SSM connection m
103 0 1 0 0.00% 0.00% 0.00% 0 AC Switch
104 4 5709 0 0.00% 0.00% 0.00% 0 Authentication P
105 0 1 0 0.00% 0.00% 0.00% 0 Auth-proxy AAA B
106 0 2 0 0.00% 0.00% 0.00% 0 EAPoUDP Process
107 0 2 0 0.00% 0.00% 0.00% 0 IP Host Track Pr
108 0 2 0 0.00% 0.00% 0.00% 0 KRB5 AAA
109 1152 49386 23 0.00% 0.00% 0.00% 0 IP Background
110 2276 28582 79 0.00% 0.00% 0.00% 0 IP RIB Update
111 60 34442 1 0.00% 0.00% 0.00% 0 CEF background p
112 6784 2485297 2 0.00% 0.00% 0.00% 0 CEF: IPv4 proces
113 12 104 115 0.00% 0.00% 0.00% 0 ADJ background
114 0 2 0 0.00% 0.00% 0.00% 0 PPP IP Route
115 0 2 0 0.00% 0.00% 0.00% 0 PPP IPCP
116 0 1 0 0.00% 0.00% 0.00% 0 IP Traceroute
117 7292 7550370 0 0.00% 0.00% 0.00% 0 TCP Timer
118 1300 10511 123 0.00% 0.00% 0.00% 0 TCP Protocols
119 0 1 0 0.00% 0.00% 0.00% 0 Socket Timers
120 18228 11429 1594 0.00% 0.00% 0.00% 0 HTTP CORE
121 0 2 0 0.00% 0.00% 0.00% 0 RLM groups Proce
122 0 1 0 0.00% 0.00% 0.00% 0 L2X Data Daemon
123 0 1 0 0.00% 0.00% 0.00% 0 ac_atm_state_eve
124 0 2 0 0.00% 0.00% 0.00% 0 SNMP Timers
125 1320 1710737 0 0.00% 0.00% 0.00% 0 RUDPV1 Main Proc
126 0 1 0 0.00% 0.00% 0.00% 0 bsm_timers
127 568 1710728 0 0.00% 0.00% 0.00% 0 bsm_xmt_proc
128 0 1 0 0.00% 0.00% 0.00% 0 COPS
129 0 2 0 0.00% 0.00% 0.00% 0 Dialer Forwarder
130 0 3 0 0.00% 0.00% 0.00% 0 Flow Exporter Ti
131 0 2 0 0.00% 0.00% 0.00% 0 ATM OAM Input
132 0 2 0 0.00% 0.00% 0.00% 0 ATM OAM TIMER
133 0 1 0 0.00% 0.00% 0.00% 0 RARP Input
134 0 1 0 0.00% 0.00% 0.00% 0 IPv6 Inspect Tim
135 0 1 0 0.00% 0.00% 0.00% 0 LAPB Process
136 0 2 0 0.00% 0.00% 0.00% 0 LFDp Input Proc
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
137 0 1 0 0.00% 0.00% 0.00% 0 PAD InCall
138 0 2 0 0.00% 0.00% 0.00% 0 X.25 Background
139 0 2 0 0.00% 0.00% 0.00% 0 PPP Bind
140 0 2 0 0.00% 0.00% 0.00% 0 PPP SSS
141 0 1 0 0.00% 0.00% 0.00% 0 MQC Flow Event B
142 35504 424737438 0 0.23% 0.25% 0.23% 0 HQF Shaper Backg
143 4068 17031478 0 0.00% 0.00% 0.00% 0 RBSCP Background
144 0 2 0 0.00% 0.00% 0.00% 0 SCTP Main Proces
145 0 1 0 0.00% 0.00% 0.00% 0 VPDN call manage
146 0 1 0 0.00% 0.00% 0.00% 0 CHKPT EXAMPLE
147 0 1 0 0.00% 0.00% 0.00% 0 CHKPT DevTest
148 0 1 0 0.00% 0.00% 0.00% 0 IPS Process
149 0 2 0 0.00% 0.00% 0.00% 0 IPS Auto Update
150 0 2 0 0.00% 0.00% 0.00% 0 SDEE Management
151 948 3338807 0 0.00% 0.00% 0.00% 0 Inspect process
152 0 1 0 0.00% 0.00% 0.00% 0 xcpa-driver
153 52 136947 0 0.00% 0.00% 0.00% 0 FW DP Inspect pr
154 1112 3338806 0 0.00% 0.00% 0.00% 0 CCE DP URLF cach
155 0 2 0 0.00% 0.00% 0.00% 0 URL filter proc
156 0 1 0 0.00% 0.00% 0.00% 0 XSM_EVENT_ENGINE
157 144 171238 0 0.00% 0.00% 0.00% 0 XSM_ENQUEUER
158 68 171238 0 0.00% 0.00% 0.00% 0 XSM Historian
159 0 1 0 0.00% 0.00% 0.00% 0 Select Timers
160 4 2 2000 0.00% 0.00% 0.00% 0 HTTP Process
161 0 2 0 0.00% 0.00% 0.00% 0 CIFS API Process
162 0 2 0 0.00% 0.00% 0.00% 0 CIFS Proxy Proce
163 0 1 0 0.00% 0.00% 0.00% 0 Crypto HW Proc
164 56 114166 0 0.00% 0.00% 0.00% 0 ACE policy loade
165 156 68505 2 0.00% 0.00% 0.00% 0 CRM_CALL_UPDATE_
166 36688 172862 212 0.00% 0.00% 0.00% 0 BGP I/O
167 0 2 0 0.00% 0.00% 0.00% 0 AAA Cached Serve
168 0 2 0 0.00% 0.00% 0.00% 0 ENABLE AAA
169 0 1 0 0.00% 0.00% 0.00% 0 EM Background Pr
170 0 1 0 0.00% 0.00% 0.00% 0 Key chain liveke
171 0 2 0 0.00% 0.00% 0.00% 0 LINE AAA
172 44 112 392 0.00% 0.00% 0.00% 0 LOCAL AAA
173 0 42 0 0.00% 0.00% 0.00% 0 MPLS Auto Mesh P
174 0 2 0 0.00% 0.00% 0.00% 0 TPLUS
175 0 2 0 0.00% 0.00% 0.00% 0 VSP_MGR
176 0 1 0 0.00% 0.00% 0.00% 0 FW_TEST_TRP
177 0 1 0 0.00% 0.00% 0.00% 0 EPM MAIN PROCESS
178 4 3 1333 0.00% 0.00% 0.00% 0 Crypto WUI
179 0 2 0 0.00% 0.00% 0.00% 0 Crypto Support
180 0 1 0 0.00% 0.00% 0.00% 0 IPSECv6 PS Proc
181 0 1 0 0.00% 0.00% 0.00% 0 CCVPM_HTSP
182 0 1 0 0.00% 0.00% 0.00% 0 CCVPM_R2
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
183 0 1 0 0.00% 0.00% 0.00% 0 EPHONE MWI Refre
184 0 1903 0 0.00% 0.00% 0.00% 0 FB/KS Log HouseK
185 0 2 0 0.00% 0.00% 0.00% 0 EPHONE MWI BG Pr
186 0 1 0 0.00% 0.00% 0.00% 0 Skinny HW confer
187 0 1 0 0.00% 0.00% 0.00% 0 CCSWVOICE
188 206492 114180 1808 0.00% 0.00% 0.00% 0 BGP Scanner
189 0 1 0 0.00% 0.00% 0.00% 0 http client proc
190 0 3 0 0.00% 0.00% 0.00% 0 BGP Event
191 0 1 0 0.00% 0.00% 0.00% 0 QOS_MODULE_MAIN
192 0 1 0 0.00% 0.00% 0.00% 0 RPMS_PROC_MAIN
193 0 1 0 0.00% 0.00% 0.00% 0 VoIP AAA
194 0 2 0 0.00% 0.00% 0.00% 0 Dialog Manager
195 184 104 1769 0.00% 0.00% 0.00% 0 crypto engine pr
196 0 4 0 0.00% 0.00% 0.00% 0 Crypto CA
197 0 1 0 0.00% 0.00% 0.00% 0 Crypto PKI-CRL
198 28008 64288 435 0.00% 0.00% 0.00% 0 encrypt proc
199 384768 28300 13596 0.00% 0.00% 0.00% 0 crypto sw pk pro
200 8 27 296 0.00% 0.00% 0.00% 0 Crypto INT
201 456 2019 225 0.00% 0.00% 0.00% 0 Crypto IKE Dispa
202 2128 2714 784 0.00% 0.00% 0.00% 0 Crypto IKMP
203 0 1 0 0.00% 0.00% 0.00% 0 IPSEC manual key
204 180 85737 2 0.00% 0.00% 0.00% 0 IPSEC key engine
205 0 1 0 0.00% 0.00% 0.00% 0 CRYPTO QoS proce
206 28 142 197 0.00% 0.00% 0.00% 0 Crypto ACL
207 0 1 0 0.00% 0.00% 0.00% 0 Crypto PAS Proc
208 0 1 0 0.00% 0.00% 0.00% 0 GDOI GM Process
209 0 1 0 0.00% 0.00% 0.00% 0 UNICAST REKEY
210 0 1 0 0.00% 0.00% 0.00% 0 UNICAST REKEY AC
211 0 1 0 0.00% 0.00% 0.00% 0 MV64 TDR Process
212 0 1 0 0.00% 0.00% 0.00% 0 IMA Traps
213 0 1 0 0.00% 0.00% 0.00% 0 SYSMGT Events
214 0 2 0 0.00% 0.00% 0.00% 0 Control-plane ho
215 0 1 0 0.00% 0.00% 0.00% 0 DATA Transfer Pr
216 0 1 0 0.00% 0.00% 0.00% 0 DATA Collector
217 0 1 0 0.00% 0.00% 0.00% 0 Async write proc
218 116 292 397 0.00% 0.00% 0.00% 0 AAA SEND STOP EV
219 136 171243 0 0.00% 0.00% 0.00% 0 RMON Recycle Pro
220 0 2 0 0.00% 0.00% 0.00% 0 RMON Deferred Se
221 0 1 0 0.00% 0.00% 0.00% 0 Syslog Traps
222 0 2 0 0.00% 0.00% 0.00% 0 EEM ED Resource
223 0 2 0 0.00% 0.00% 0.00% 0 EEM ED Routing
224 0 3 0 0.00% 0.00% 0.00% 0 EEM ED Track
225 80 53575 1 0.00% 0.00% 0.00% 0 Crypto cTCP proc
226 0 1 0 0.00% 0.00% 0.00% 0 IP SLAs Ethernet
227 4 1 4000 0.00% 0.00% 0.00% 0 RMON Packets
228 820 1709984 0 0.00% 0.00% 0.00% 0 trunk conditioni
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
229 0 1 0 0.00% 0.00% 0.00% 0 trunk conditioni
230 12 120 100 0.00% 0.00% 0.00% 0 EEM Server
231 4 2 2000 0.00% 0.00% 0.00% 0 Call Home proces
232 52 260 200 0.00% 0.00% 0.00% 0 Syslog
233 0 1 0 0.00% 0.00% 0.00% 0 VPDN Test
234 0 2 0 0.00% 0.00% 0.00% 0 EEM Policy Direc
235 0 2 0 0.00% 0.00% 0.00% 0 EEM ED CLI
236 0 3 0 0.00% 0.00% 0.00% 0 EEM ED Counter
237 0 3 0 0.00% 0.00% 0.00% 0 EM ED GOLD
238 0 3 0 0.00% 0.00% 0.00% 0 EEM ED Interface
239 0 3 0 0.00% 0.00% 0.00% 0 EEM ED IOSWD
240 0 3 0 0.00% 0.00% 0.00% 0 EEM ED Ipsla
241 0 3 0 0.00% 0.00% 0.00% 0 EEM ED None
242 0 2 0 0.00% 0.00% 0.00% 0 EEM ED Nf
243 0 3 0 0.00% 0.00% 0.00% 0 EEM ED OIR
244 0 3 0 0.00% 0.00% 0.00% 0 EEM ED RF
245 0 3 0 0.00% 0.00% 0.00% 0 EEM ED SNMP
246 0 2 0 0.00% 0.00% 0.00% 0 EEM ED SNMP Noti
247 36 42890 0 0.00% 0.00% 0.00% 0 EEM ED Timer
248 0 3 0 0.00% 0.00% 0.00% 0 EEM ED Test
249 0 3 0 0.00% 0.00% 0.00% 0 EEM ED Config
250 0 3 0 0.00% 0.00% 0.00% 0 EEM ED Env
251 0 3 0 0.00% 0.00% 0.00% 0 EEM ED RPC
252 0 2 0 0.00% 0.00% 0.00% 0 cpf_process_msg_
253 0 1 0 0.00% 0.00% 0.00% 0 Key Proc
254 36 28543 1 0.00% 0.00% 0.00% 0 Call Home Timer
255 0 1 0 0.00% 0.00% 0.00% 0 tHUB
256 0 1 0 0.00% 0.00% 0.00% 0 Async write proc
257 104 953 109 0.00% 0.00% 0.00% 0 SSH Event handle
258 16 28543 0 0.00% 0.00% 0.00% 0 Secure Login
259 84 54 1555 0.00% 0.00% 0.00% 0 Tunnel Security
260 56 67 835 0.00% 0.00% 0.00% 0 Crypto SS Proces
261 0 1 0 0.00% 0.00% 0.00% 0 cpf_process_tpQ
262 0 1 0 0.00% 0.00% 0.00% 0 TCP Listener
263 0 2 0 0.00% 0.00% 0.00% 0 IP Flow Top Talk
264 1180 3338804 0 0.00% 0.00% 0.00% 0 IP NAT Ager
265 0 1 0 0.00% 0.00% 0.00% 0 IP NAT WLAN
266 24 28563 0 0.00% 0.00% 0.00% 0 IP SLAs Event Pr
267 434504 1489526 291 0.00% 0.00% 0.00% 0 IP SNMP
268 170304 877961 193 0.00% 0.00% 0.00% 0 PDU DISPATCHER
269 495704 877992 564 0.00% 0.00% 0.00% 0 SNMP ENGINE
270 0 2 0 0.00% 0.00% 0.00% 0 IP SNMPV6
271 0 1 0 0.00% 0.00% 0.00% 0 SNMP ConfCopyPro
272 0 1 0 0.00% 0.00% 0.00% 0 SNMP Traps
273 1185420 1715196 691 0.00% 0.00% 0.00% 0 NTP
274 412 29 14206 0.00% 0.00% 0.00% 0 VTEMPLATE Backgr
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
275 18608 174262 106 0.00% 0.00% 0.00% 0 BGP Router
276 36 27171 1 0.00% 0.00% 0.00% 0 DFS flush period
277 8 12 666 0.00% 0.00% 0.00% 0 Collection proce
278 16 651 24 0.00% 0.00% 0.00% 0 CRYPTO IKMP IPC
279 1724 850 2028 0.00% 0.00% 0.00% 2 SSH Process
281 0 1 0 0.00% 0.00% 0.00% 0 Skinny MOH Event
282 64 173856 0 0.00% 0.00% 0.00% 0 Skinny Socket Se
283 0 1451 0 0.00% 0.00% 0.00% 0 Web Write Housek
==============================================================
wish to help ASAPJosephDoherty wrote:DisclaimerThe Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.Liability DisclaimerIn no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.PostingThe fact you are matching with any ACLs, will decrease maximum performance.The fact you are using a policy-may, will decrease maximum performance.The fact is a -G2 only has finite capacity.In other words, what you're seeing might be completely normal for your traffic volume, your traffic composition and your configuration.If you believe your router is overloaded, and generally above 75% CPU might be so considered, either you'll need a faster device (see ASR 1Ks), or you might try changing your configuration to decrease your configuration load on the router.What's your CPU load if your remove the policy-map from the interface?If removing the policy-map from the interface shows a significant CPU loading decrease - QED.If you need/desire such QoS, then you'll want a "faster" router.You might be also able to decrease your CPU a little by some "tuning". I already mention the TurboACL feature statement. With ACLs, fewer are faster, and how they ordered (especially without TurboACL) impacts CPU. How you order you class-maps, within a policy, and how the match statements are ordered will also have some impact on the CPU load. If buffers are being allocated/deallocated, that too will impact CPU loading. I assume CEF is enabled, but for some traffic, flow caching might decrease CPU load.Remember a software based router, like the 7200s, are, more or less, a computer that takes your configuration and determines what's to be done with every packet it "sees". The more your configuration requires for per packet analysis, the more load for each packet.There are whitepapers addressing high CPU load caused by "process switching", but what you posted appears to be mostly all interrupt processing, which is "fast path", or optimal, packet forwarding. There's not much you can normally do to improve against that, other than insuring your configuration is as optimal as possible for your needs (again, things like sequencing/ordering of statements).
hi ,
thanks very very much for this nice information,
let me answer you :
you said that NPE G2 has finite capacity , but how to know this full capacity ???
i mean that my policy map is matching the traffic , but the matched traffic is not being enhancemend ??!!!
last about two weeks , the matched traffic of youtube was excellent and no interrupt durting the my rush hour.
i didnt change any thing, but my bw increased from 730 Mbps to 760Mbps ,
im un able to make sure that i need to chnage my platform to faster one.
agian
my cpu is 60 % without QOS
after QOS it increase to 80-85 %
agian ,
about NBAR
i want to tell you that i cant depend on NBAR , as an example , im matching the ips of videos of facebook , i cant depend on NBAR because it is https videos.
but in summary ,
my qos is matching well , but i have no real enhancement for my traffic.
did you face my issue before ???
i mean have you see like my problem ?
like my router platform with cpu over 80 % and 750Mbps , and matched qos without good result ??
note that i upgraded to iso 15 , but seems same issue !!!
regards -
How to apply Qos in the precedence of cache server
m in an isp and iwant to apply the QOS to enhance my network internet performance
actually i have two requests , i will start with showing brief topology about my network and start asking the questions .
here is the topology below :
from the topology above , my access is only on R1 which is BGP internet gateway router and R2 is my ISP router.
1- i want to apply Qos on R1 so that a subnet of 32 ips to have gurantee bandwidth of 30M .
assume the subnet is 10.20.30.0/27 that need to be bw gurantee .
2- i want the download traffic by idman or ftp on my Router R1 dont exceed 50 % of my total bw .
i mean that i have 450M bandwith from my isp , & sometimes we have a slow in browsing , so i want to enhance the browsing quality because its more important that downloading files from internet.
here is my two requests above , i dont know how it will work with the precedence of the cache server .
anyway , i will paste my config of router and i will replace my puplic ips with xxx for privacy .
7200Gateway#sh run
Building configuration...
Current configuration : 10149 bytes
upgrade fpd auto
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname 7200Gateway
boot-start-marker
boot-end-marker
logging message-counter syslog
logging buffered 50000
enable secret xxxxxxxxxxxxxx
no aaa new-model
ip source-route
ip wccp 80 redirect-list CACHE80
ip wccp 90 redirect-list CACHE90
ip cef
no ip domain lookup
ip accounting-threshold 4294967295
login block-for 180 attempts 3 within 60
login quiet-mode access-class telnet
login on-failure log
login on-success log
no ipv6 cef
multilink bundle-name authenticated
username xxxxxx password xxxxx
archive
log config
hidekeys
interface GigabitEthernet0/1
description LAN
bandwidth 230000
ip address 10.160.150.2 255.255.255.0
ip wccp 80 redirect in
ip policy route-map CACHE-REDIRECT
load-interval 30
duplex auto
speed auto
media-type rj45
negotiation auto
interface FastEthernet0/2
no ip address
shutdown
duplex auto
speed auto
interface GigabitEthernet0/2
description Cache
bandwidth 150000
ip address x.x.x.x 255.255.255.248
ip wccp redirect exclude in
load-interval 30
duplex auto
speed 1000
media-type rj45
negotiation auto
interface GigabitEthernet0/3
description Internet
bandwidth 230000
ip address x.x.x.x 255.255.255.252
ip wccp 90 redirect in
load-interval 30
duplex full
speed 1000
media-type sfp
negotiation auto
router bgp zzzzzzz
no synchronization
bgp log-neighbor-changes
network xxxx mask xxxxx
network xxxx mask xxxx
network xxxx mask xxxxx
network xxxx mask xxxx
network xxxx mask xxxxx
network xxxx mask xxxx
redistribute connected
redistribute static
neighbor zzzzzzzz remote-as zzzzzzz
neighbor zzzzzzz password zzzzzzz
neighbor zzzzzz route-map Pipo out
no auto-summary
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 xxxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
ip route xxxxxxxx 255.255.0.0 xxxxxxxxxx
no ip http server
no ip http secure-server
ip flow-top-talkers
top 200
sort-by bytes
cache-timeout 5000
ip access-list extended bb
permit ip xxxx.xxxx.xx.0 0.0.1.255 any
ip access-list extended CACHE80
permit tcp xxxxxxx any eq www
ip access-list extended CACHE90
permit tcp any xxxxx.0 0.0.0.255
ip access-list extended pipo
permit ip xxxxx xxxxxxx any
permit ip xxxxx xxxxxxx any
ip access-list extended private
permit tcp 172.16.0.0 0.0.255.255 any eq www
permit ip 10.20.30.0 0.0.0.255 any
ip access-list extended telnet
permit ip xxxxxx xxxxxxx.255.255 any log
permit ip xxxx xxxxx 0.0.0.255 any log
ip prefix-list bb seq 5 permit xxxxx
ip prefix-list bbseq 10 permit xxxxxx
logging history size 500
no cdp run
route-map pipo permit 10
match ip address prefix-list pipo1
route-map pipo permit 20
match ip address prefix-list newsubnet
set metric 500
set origin incomplete
set as-path prepend xxxxxxxxx
route-map permit 10
match ip address prefix-list bibo
route-map CACHE-REDIRECT permit 10
match ip address private
set ip next-hop 1vvvvvv
route-map CACHE-REDIRECT permit 20
match ip address bibo e1
set ip next-hop vvvvvv
route-map CACHE-REDIRECT permit 30
match ip address pipo
set ip next-hop vvvvvvvvvv
route-map CACHE-REDIRECT permit 100
snmp-server community xxxxxx RO
control-plane
dial-peer cor custom
line con 0
password xxxxxxxx
logging synchronous
login
stopbits 1
line aux 0
stopbits 1
line vty 0 4
exec-timeout 60 0
password xxxxxxxxxxxxxxxxx
logging synchronous
login local
endHi Vinay,
Please check the program. I have used the replace statement but it is not working.
IF NOT v_sap_bom_rec IS INITIAL.
Spliting the records at '~' delimiter
SPLIT v_sap_bom_rec AT c_del INTO wa_bom_file-model_name
wa_bom_file-product_code
wa_bom_file-description
wa_bom_file-product_type
wa_bom_file-mfg_part_num
wa_bom_file-mfg_part_desc.
REPLACE cl_abap_char_utilities=>horizontal_tab IN wa_bom_file-mfg_part_desc WITH space .
wa_bom_file-status = c_status.
APPEND wa_bom_file TO i_bom_file.
But it is not working.
Please help me..
Thanks
Neelima -
How to change default FCoE QoS class - Nexus 5020
I see that on a Nexus 5020, the default FCoE QoS class is 50%. I am not using FCoE so I would like to adjust this value to 0%. I switch complains and says I can't change default values. How should I go about getting around this to eliminate the FCoE queue and give 100% BW to default? Thanks.
No. The default classloader is a builtin classloader in
the JRE. You can use other classloaders.
The java.net.URLClassLoader is provided in
the JDK. That's the only one. Otherwise you
should subclass ClassLoader and implement
the loadClass method (f.i.
loadClass("my.program") {
String file="my.program".replace('.','/') + ".class";
// find the file in classpath
// read the class file in a byte[]
return defineClass(byte[]);
although this is not the advised way to do it. Search the web for how to implement a classloader directly. -
VoIP QoS for Site-to-Site Tunnel
Hi all,
I need some help with setting up QoS for VoIP between two Cisco ASA 5505 with Site-to-Site VPN.
There is no need for bandwith reservation, only DSCP 46 (EF) should be highest and DSCP 26 second highest queue and the rules should only apply to a site-to-site VPN.
Usually i try to configure the ASAs via ASDM and found out in the Cisco Documentations how to setup QoS for the DSCP bits with a Service Policy and how to set up QoS for a Site-to-Site VPN (Service Policy Rule -> Traffic Match). But how do i configure the QoS for a DSCP bit to only apply to a Site-to-Site Tunnel? And how do i configure different priorities for the two DSCP bits, is this defined by the order of Service Policies?
The QoS has to be enabled on both ASAs for the inside interface?
Thanks in advance
TobiasHi Collin,
ok so from the document i think this has to be added on both ASAs to prioritize DSCP 46. Could you have a quick look if this is all i need?
class-map voice_traffic
match dscp ef
class-map data
match tunnel-group <Tunnel Name>
match flow ip destination-address
policy-map voice_policy
class voice_traffic
priority
class Data
police output 200000 37500
service-policy voice_policy interface outside
But there is still the question how two configure another DSCP bit for priority 2, I could not find out how this is done, neither CLI nor ASDM. Any ideas?
BR
Tobias -
Problem with QOS for SIP on RV082
Hello,
I have problem with quality of VOIP call with Linskys RV082. Firmware is 2.0.0.19tm.
Router is configured as dual-wan , one port (WAN2) is for ADSL 8000/512kb and other one is (WAN1) SHDSL 8000/8000kb.
VOIP traffic from certain IP of LAN is routed to WAN2 (through protocol binding). We have quaranted QOS on ADSL by ISP.
Problem is that voice is dropping when we load WAN2 with other data connection. Last week i reload new firmware, restore default factory and configured router whole again. All was ok only for 1 day and then voice was dropping again. I mean that problem is at mark packets, because when I put VOIP PBX in front of behind router , QOS is working fine.
Can you help me? Is this know issue?
Thanks.
Jan Babak
Message was edited by: jabacomCZthank you for reply !!!
below is the show output :
ciscoasa# show priority-queue statistics outside_wan
Priority-Queue Statistics interface outside_wan
Queue Type = BE
Tail Drops = 0
Reset Drops = 0
Packets Transmit = 7971924
Packets Enqueued = 0
Current Q Length = 0
Max Q Length = 0
Queue Type = LLQ
Tail Drops = 0
Reset Drops = 0
Packets Transmit = 189321
Packets Enqueued = 0
Current Q Length = 0
Max Q Length = 0
ciscoasa#
so does the command look like, the one I should use instead of priority-queue outside_wan ?? -
Is there ANY way to get QOS with an airport extreme base station?
I recently moved and decided to go with Primus VOIP for my phone line. It works fine as long as i don't have any torrents going...if i do then call quality goes to **** (i wish someone would've told me before)
I was told to use a QOS on teh VOIP ports...but my airport extreme doesn't support this (and apparently neither will the new one). Honestly this is something Apple REALLY needs to fix. This is outrageous. They're supposed to be on teh cutting edge of technology, and their routers don't even won't properply with VOIP services??? That's ********.
Is there any way i could get this to work - perhaps thru software?
It seems the only solution i have is to get a Linksys router and sell off the airportSorry that this may not seem like an ideal solution, but one option is to use an application that runs on a Windows PC that allows you to format HDDs for HFS+. Once formatted as such, it can be shared out to either OS X, Windows, or Linux users from an AirPort Extreme or Time Capsule. HFS+, like NTFS, supports much larger HDDs.
-
How to configure QOS on certain IP in the Cisco ASA 5510
Hi,
I am need to configure QOS on certain IP in the Cisco ASA 5510. Assume the IP's are 10.0.1.5 , 10.0.1.6 , 10.0.1.7. Here i have to configure 512 KBPS for 10.0.1.5 and 2 MBPS for 10.0.1.6 and 10.0.1.7
Can this done on a ASA 5510 series? if yes can you help me how ?
Regards,
VenkatYes you can do it.You can match the ip addresses in an access-list, put in a class-map and the class-map in a policy map that will do policing.
Good examples for what you want to do are here https://supportforums.cisco.com/docs/DOC-1230
I hope it helps.
PK -
[Solved for me]Distinguishing SSH and SFTP (for QoS purposes)
Hi there,
I'm thinking about shutting down the FTP on my homeserver and use SFTP instead. There is only one thing I couldn't solve so far: In my router I have QoS-rules that make FTP low priority traffic so my normal activities don't get affected by the file transfers. I would like to have the same setup for the SFTP. Now the problem is this: SFTP and SSH are both coming from the same ssh server, listening on port 22. So there is no way of distinguishing them on a ip/port basis. Is there any way of distinguishing SFTP and SSH? Like using iptables to tag one of them and then doing QoS based on the tag or something along those lines? I don't want to slow down my ssh-connections together with the sftp. If anyone has an idea how to accomplish this I would be really glad to hear about it.
Thanks in advance
seiichiro0185
Last edited by seiichiro0185 (2010-08-22 11:27:32)briest wrote:Well, a simple, though definitely not bulletproof solution: define multiple ports in sshd_config, then use one of them for sftp, and another for ssh?
Thanks for this hint, I didn't know that ssh could listen on multiple ports. Its not totally bulletproof, but good enough for my case. The only people who will have access to the server are trustworthy and won't fiddle with the settings to circumvent my restrictions.
Thanks to all of you for your suggestions. -
How to set up a QOS on 3750 switch to limit outbound bandwidth on a server ?
Hi,
I have three LAN ports on a VM server. I want to limit a VM guest (guest server) outbound bandwidth to 3750 swith .
How do I do it ? I want to apply QoS on the switch.
thanksDisclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
If you're looking to limit bandwidth FROM your server, you can use an ingress policy on the server's interface and police selectively. For example, if your specific VM has its own IP address, you could police inbound (from the server) traffic matching that IP. -
Need help with QoS config/setup for my home network.
I have a home network that spans two buildings, has and FTP download server, VoIP phones,and several computers among other IP devices. I run a home based business where my clients get access to the company FTP download server (NOT illegal file sharing). the problem is that when they are downloading files my VoIP takes a big hit and gets choppy when speaking to my customers. Below is the layout of the network.
Our Internet access is Verizon 4G, there are no other options available at this time or we would switch. The Verizon 4G MiFi connects to a TP-Link wifi router that then connects to port fa0/5 on the Office 3550PoE switch. There is a trunk between the Office switch to the House 3550PoE switch. The House switch then connects to the Shop 3524XL switch also using a trunk. Please note that EVERYTHING works fine other than the VoIP issue, VoIP makes and receives calls without connections issues.
Auto QoS has been run on the Office switch ports fa0/1 and fa0/2 as well as on the House switch ports fa0/3 and fa0/5. There is NO auto QoS on the 3524XL
What is the best way to give VoIP traffic top priority over FTP and web browsing when going out port fa0/5 on the Office Switch? Over the internal network we are not having any call quality issues between the IP phones, just calls to our SIP provider. Yes, I understand that once calls exit the Office switch to the TP-Link wifi router there will not be any QoS. But, if I can give priority to the packets at the layer 3 Office switch (or wherever you suggest) then at least I will not have to kill a users FTP download while I am on the phone.
Thank YouI can make ANY changes necessary, just need to know what to do.
First, did you notice the output of the command sh mls qos fa0/5 above? Is it working correctly?
Next, Yes I do have version W17 and can install if if needed. The lost of possible commands I listed above was from the conf t - config interface fa0/x level. There is class and policy mapping commands the the config global level along with all these other commands:
aaa Authentication, Authorization and Accounting.
access-list Add an access list entry
alias Create command alias
arp Set a static ARP entry
banner Define a login banner
boot Boot Commands
buffers Adjust system buffer pool parameters
cdp Global CDP configuration subcommands
cgmp Global CGMP configuration commands
class-map Configure QoS Class Map
clock Configure time-of-day clock
cluster Cluster configuration commands
default Set a command to its defaults
default-value Default character-bits values
downward-compatible-config Generate a configuration compatible with older software
enable Modify enable password parameters
end Exit from configure mode
errdisable Error disable
exception Exception handling
exit Exit from configure mode
file Adjust file system parameters
help Description of the interactive help system
hostname Set system's network name
interface Select an interface to configure
ip Global IP configuration subcommands
line Configure a terminal line
logging Modify message logging facilities
mac-address-table Configure the MAC address table
map-class Configure static map class
map-list Configure static map list
mvr Enable/Disable MVR on the switch
no Negate a command or set its defaults
ntp Configure NTP
policy-map Configure QoS Policy Map
power power configuration
priority-list Build a priority list
privilege Command privilege parameters
queue-list Build a custom queue list
rmon Remote Monitoring
scheduler Scheduler parameters
service Modify use of network based services
shutdown Shutdown system elements
snmp-server Modify SNMP parameters
spanning-tree Spanning Tree Subsystem
stackmaker Specify stack name and add its member
tacacs-server Modify TACACS query parameters
tftp-server Provide TFTP service for netload requests
time-range Define time range entries
udld Configure global UDLD setting
username Establish User Name Authentication
vmps VMPS settings
vtp Configure global VTP state -
QoS / Native VLAN Issue - Please HELP! :)
I've purchased 10 Cisco Aironet 2600 AP’s (AIR-SAP2602I-E-K9 standalone rather than controller based).
I’ve configured the WAP’s (or the first WAP I’m going to configure and then pull the configuration from and push to the others) with 2 SSID’s. One providing access to our DATA VLAN (1000 – which I’ve set as native on the WAP) and one providing access to guest VLAN (1234). I’ve configured the connecting DELL switchport as a trunk and set the native VLAN to 1000 (DATA) and allowed trunk traffic for VLAN’s 1000 and 1234. Everything works fine, when connecting to the DATA SSID you get a DATA IP and when you connect to the GUEST SSID you lease a GUEST IP.
The problem starts when I create a QoS policy on the WAP (for Lync traffic DSCP 40 / CS5) and try to attach it to my VLAN’s. It won’t let me attach the policy to VLAN 1000 as it’s the native VLAN. If I change VLAN 1000 on the WAP to NOT be the native VLAN I can attach the policies however wireless clients can no longer attach to either SSID properly as they fail to lease an IP address and instead get a 169.x.x.x address.
I'm sure I'm missing something basic here so please forgive my ignorance.
This is driving me insane!
Thanks to anyone that provides assistance. Running config below and example of the error...
User Access Verification
Username: admin
Password:
LATHQWAP01#show run
Building configuration...
Current configuration : 3621 bytes
! Last configuration change at 02:37:59 UTC Mon Mar 1 1993 by admin
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LATHQWAP01
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
no ip routing
dot11 syslog
dot11 vlan-name Data vlan 1000
dot11 vlan-name Guest vlan 1234
dot11 ssid LatitudeCorp
vlan 1000
authentication open
authentication key-management wpa version 2
wpa-psk ascii
dot11 ssid LatitudeGuest
vlan 1234
authentication open
authentication key-management wpa version 2
guest-mode
wpa-psk ascii
crypto pki token default removal timeout 0
username admin privilege 15 password!
class-map match-all _class_Lync0
match ip dscp cs5
policy-map Lync
class _class_Lync0
set cos 6
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1234 mode ciphers aes-ccm
encryption vlan 1000 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
stbc
station-role root
interface Dot11Radio0.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 1234 mode ciphers aes-ccm
encryption vlan 1000 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
no dfs band block
stbc
channel dfs
station-role root
interface Dot11Radio1.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface GigabitEthernet0.1000
encapsulation dot1Q 1000 native
no ip route-cache
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.1234
encapsulation dot1Q 1234
no ip route-cache
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
service-policy input Lync
service-policy output Lync
interface BVI1
ip address 10.10.1.190 255.255.254.0
no ip route-cache
ip default-gateway 10.10.1.202
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
transport input all
end
LATHQWAP01#conf
Configuring from terminal, memory, or network [terminal]? t
Enter configuration commands, one per line. End with CNTL/Z.
LATHQWAP01(config)#int dot11radio1.1000
LATHQWAP01(config-subif)#ser
LATHQWAP01(config-subif)#service-policy in
LATHQWAP01(config-subif)#service-policy input Lync
set cos is not supported on native vlan interface
LATHQWAP01(config-subif)#Hey Scott,
Thank you (again) for your assistance.
So I' ve done as instructed and reconfigured the WAP. I've added an additional VLAN (1200 our VOIP VLAN) and made this the native VLAN - so 1000 and 1234 are now tagged. I've configure the BVI interface with a VOIP IP address for management and can connect quite happily. I've configured the connecting Dell switchport as a trunk and to allow trunk vlans 1000 (my DATA SSID), 1200(native) and 1234 (MY GUEST SSID). I'm now back to the issue where when a wireless client attempts to connect to either of my SSID's (Guest or DATA) they are not getting a IP address / cannot connect.
Any ideas guys? Forgive my ignorance - this is a learning curve and one i'm enjoying.
LATHQWAP01#show run
Building configuration...
Current configuration : 4426 bytes
! Last configuration change at 20:33:19 UTC Mon Mar 1 1993 by Cisco
version 15.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname LATHQWAP01
logging rate-limit console 9
enable secret 5
no aaa new-model
no ip source-route
no ip cef
dot11 syslog
dot11 vlan-name DATA vlan 1000
dot11 vlan-name GUEST vlan 1234
dot11 vlan-name VOICE vlan 1200
dot11 ssid LatitudeCorp
vlan 1000
authentication open
authentication key-management wpa version 2
mobility network-id 1000
wpa-psk ascii
dot11 ssid LatitudeGuest
vlan 1234
authentication open
authentication key-management wpa version 2
mbssid guest-mode
mobility network-id 1234
wpa-psk ascii
no ids mfp client
dot11 phone
username CISCO password
class-map match-all _class_Lync0
match ip dscp cs5
policy-map Lync
class _class_Lync0
set cos 6
bridge irb
interface Dot11Radio0
no ip address
encryption vlan 1000 mode ciphers aes-ccm
encryption vlan 1234 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
stbc
mbssid
station-role root
interface Dot11Radio0.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio0.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio0.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 spanning-disabled
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1
no ip address
encryption vlan 1000 mode ciphers aes-ccm
encryption vlan 1234 mode ciphers aes-ccm
ssid LatitudeCorp
ssid LatitudeGuest
antenna gain 0
peakdetect
no dfs band block
stbc
mbssid
channel dfs
station-role root
interface Dot11Radio1.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 subscriber-loop-control
bridge-group 255 spanning-disabled
bridge-group 255 block-unknown-source
no bridge-group 255 source-learning
no bridge-group 255 unicast-flooding
service-policy input Lync
service-policy output Lync
interface Dot11Radio1.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface Dot11Radio1.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 subscriber-loop-control
bridge-group 254 spanning-disabled
bridge-group 254 block-unknown-source
no bridge-group 254 source-learning
no bridge-group 254 unicast-flooding
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0
no ip address
duplex full
speed auto
interface GigabitEthernet0.1000
encapsulation dot1Q 1000
bridge-group 255
bridge-group 255 spanning-disabled
no bridge-group 255 source-learning
service-policy input Lync
service-policy output Lync
interface GigabitEthernet0.1200
encapsulation dot1Q 1200 native
bridge-group 1
bridge-group 1 spanning-disabled
no bridge-group 1 source-learning
interface GigabitEthernet0.1234
encapsulation dot1Q 1234
bridge-group 254
bridge-group 254 spanning-disabled
no bridge-group 254 source-learning
service-policy input Lync
service-policy output Lync
interface BVI1
mac-address 881d.fc46.c865
ip address 10.10. 255.255.254.0
ip default-gateway 10.10.
ip forward-protocol nd
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
login local
transport input all
sntp server ntp2c.mcc.ac.uk
sntp broadcast client
end
LATHQWAP01# -
Configuring QoS for FIOS Router MI-424WR: Traffic Priority and Shaping
Please only read on if you are an experienced internet user familiar with setting the advanced QoS and Firewall settings for the MI-424WR and make use of wireless adaptors from a PC to provide connectivity.
This is my first post and my first week since I moved from Time Warner Cable over to FIOS for iNet (plus HDTV and phone). While all my services work, the router as delivered and setup is not optimum for internet quality of service. Instead it was probably out of the box optimized for HDTV and telephone to satisfy most customers and reduce support overhead. The average FIOS consumer is multimedia sensitive, but that is not so in my genre of internet consumer. Here in lies the core of my reason for seeking help from like minded and experienced users in this community.
One of the main driving forces in my switching to FIOS was to improve my multiplayer gaming experience where ultra low ping latency and high upload data rates dramatically affect the quality of connection and thus gameplay. The cable internet service from TimeWarner was providing solid 2MB/1MB down/up data rates with no issues like what Im having now with FIOS. Again the reason for the switch was both financial and in hope of gaining better data rates and quality of service. Now with FIOS Im getting about 24/15 down/up data rate on the Extreme FIOS 25/25 plan when measured from my house to Los Angeles server (50 miles away) via Speedtest.net or DslReports.com/tests. Latency wise, the ping has gone down from 150 to 50ms when measured to my friends who I connect to online that are on the East coast. The data rate and latency has greatly improved in going from Cable to FIOS. So far, so good.
Where the problem shows up now, is that now I get an internet "hiccup" every 5-10 minutes that lasts about 1/2 to 2 seconds. For the average internet user that just streams multimedia or cruises on the net; this is probably undetectable or noticed. I never had this problem over the same PCs connected wirelessly to my DLINK DGL-4500 Gaming Router when my ISP was TimeWarner's cable service. Now, using the FIOS and MI-424WR router with everythings being the same; Im experiencing this degregation in quality of service. Even putting the PC's IP into the DMZ doesnt make any difference, so it is not related to port forwarding. The issue is squarely in the lap of FIOS and this router as delivered and configured. This is where the "game" is a foot, and where I need expertise in an area Im new to.
I am not new to being hands on with inet trouble shooting asI have been setting up my own home network (I work from home over VPN to work) for decades; I would like to leverage the skills of those who are experts in the area that I think can address this issue. That being QoS and the other device class mechanisms of this router. Its my guess that this periodic hiccup can be minimized and even eliminated using these advanced features of this all-in-one TV/iNet/Tele router.
With that context being laid down, this hiccup doesnt show up if:
a. I connect two PCs connected to the same ethernet hub of the MI-424WR (traffic just over the LAN and not WAN)
b. When I was on Cable with my own gaming router wirelessly DHCP connected to my PC and using port forwarding or using the DMZ.
The hiccup does exist when:
a. Going from internet through the MI-424WR to the wireless DHCP connected PC with port forwarding
b. Even putting the wireless DHCP connected PC into the MI-424WR's DMZ has no effect
I did read the manual and tried some QoS pritority and shaping and managed to reduce how often the hiccup occured, but I was just making guesses at the settings. I put in the IP for the PCs I use for my gaming applications (which are very ping and jitter sensitive) into the QoS priority (value 7) and shaping GUI. Im hoping someone with experience can tell me exactly how to use it and what settings to input. Im not clear on the device and connection types offered in the QoS menus.
Another thing, is I couldnt find settings for the turning on/off the ICMP echo. But I assume this is on because it can be pinged by folks on the net to my WAN IP.
Here is the manual for the Verizon provided M424WR router (Current Version of firmware: 20.10.7)
download link
Here are the QoS traffic priority and shaping values Ive been experimenting with:
Click to view QoS Traffic Priority
Click to view QoS Traffic Shaping
And why it matters to have a solid and stable inet connection for internet gaming? The hiccup causes slewing or jitter which equates to positional errors in the 3D world that ruins the smooth gameplay that is needed for high end gaming.
Heres a snapshot of me flying the wing of another flight simmer who is on the East coast and me on the West coast.
Click to view
Thank you in advance.
Thomas "AV8R"
MSEETMAS wrote:
the router as delivered and setup is not optimum for internet quality of service. Instead it was probably out of the box optimized for HDTV and telephone to satisfy most customers and reduce support overhead.
That's not accurate. VZ telephone service does not go through the Actiontec. Also, there are no default settings for QOS in the Actiontec since QOS is rarely needed with FIOS upload speeds.
TMAS wrote:I get an internet "hiccup" every 5-10 minutes that lasts about 1/2 to 2 seconds.
You should not be experiencing periodic "hiccups". Something is clearly amiss.
TMAS wrote:
With that context being laid down, this hiccup doesnt show up if:a. I connect two PCs connected to the same ethernet hub of the MI-424WR (traffic just over the LAN and not WAN)
The hiccup does exist when:
a. Going from internet through the MI-424WR to the wireless DHCP connected PC with port forwarding
b. Even putting the wireless DHCP connected PC into the MI-424WR's DMZ has no effect
Lets see. The issue shows up on a wireless connection, but not a wired connection. You think this is a QOS issue and not a wireless issue why? Have you tried changing the wireless channel? It very possible you have neighbors on the same channel. Is the DGL-4500 wireless still on? Could that be interfering?TMAS wrote:
Another thing, is I couldnt find settings for the turning on/off the ICMP echo.
The settting to enable/disable ICMP echo is on the Firewall/Remote Administration page.
TMAS wrote:
Here are the QoS traffic priority and shaping values Ive been experimenting with:Click to view QoS Traffic Priority
Click to view QoS Traffic Shaping
The traffic proirity settings you linked are applied only to your wireless connections. QOS between the router and your wireless PC will only serve to prioritize traffic between the router and that PC and have no affect on your internet traffic. Assuming you are not running browsers, VOIP and other traffic from that PC while you're gaming, then that will not accomplish anything. i.e. You're giving your only traffic highest priority, but that traffic is not competing with anything (except other nearby wireless connections on the same channel).
On the traffic shaping screenshot, you have broadband ethernet checked, but according to your other thread, your WAN connection is Broadband Coax, not Broadband ethernet. -
Version 03.03.00.XO - MLS QOS not supported
Hi All,
Anyone face the same problem with the following IOS Version?
MLS QOS is not supported in global command.
Switch#sh ver
Cisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500es8-UNIVERSALK9-M), Version 03.03.00.XO RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2013 by Cisco Systems, Inc.
Compiled Wed 14-Aug-13 07:26 by prod_rel_team
Cisco IOS-XE software, Copyright (c) 2005-2013 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: 15.1(1r)SG2
Switch uptime is 6 minutes
System returned to ROM by power-on
Running default software
Jawa Revision 3, RadTrooper Revision 0x0.0x41, Conan Revision 0x1449
Last reload reason: power-on
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Information for 'WS-X45-SUP8-E'
License Level: entservices Type: Permanent
Next reboot license Level: entservices
cisco WS-C4506-E (P5040) processor (revision 2) with 4194304K bytes of physical memory.
Processor board ID FXS1812Q346
P5040 CPU at 2.2GHz, Supervisor 8-E
Last reset from PowerUp
1 Virtual Ethernet interface
20 Ten Gigabit Ethernet interfaces
511K bytes of non-volatile configuration memory.
Configuration register is 0x2101
SWITCH(config)#mls qos
^
% Invalid input detected at '^' marker.
SWITCH(config)#
SWITCH(config)#?
Configure commands:
aaa Authentication, Authorization and Accounting.
access-list Add an access list entry
access-session Access Sesion Global Configuration Commands
agent-server Modify DNS server properties
alias Create command alias
ancp Configure ANCP
archive Archive the configuration
arp Set a static ARP entry
async-bootp Modify system bootp parameters
audit Router Audit
authentication Auth Manager Global Configuration Commands
auto Configure Automation
banner Define a login banner
beep Configure BEEP (Blocks Extensible Exchange
Protocol)
bfd BFD configuration commands
bfd-template BFD template configuration
boot Modify system boot parameters
bridge Bridge Group.
buffers Adjust system buffer pool parameters
bulkstat Bulkstat Application
call-home Enter call-home configuration mode
cdp Global CDP configuration subcommands
cef Cisco Express Forwarding
cisp Set CISP parameters
class-map Configure CPL Class Map
clns Global CLNS configuration subcommands
clock Configure time-of-day clock
cluster Cluster configuration commands
cns CNS agents
comet-server Configure comet-server properties
config-register Define the configuration register
configuration Configuration access
control-plane Configure control plane services
crypto Encryption module
cts Cisco Trusted Security commands
default Set a command to its defaults
default-value Default character-bits values
define interface range macro definition
device-sensor IOS Sensor Commands
diagnostic Configure diagnostic information
dns-server Modify DNS server properties
dnsix-dmdp Provide DMDP service for DNSIX
dnsix-nat Provide DNSIX service for audit trails
do-exec To run exec commands in config mode
dot1x IEEE 802.1X Global Configuration Commands
downward-compatible-config Generate a configuration compatible with older
software
eap EAP Global Configuration Commands
emm Specify pre-loading of MDF
enable Modify enable password parameters
end Exit from configure mode
energywise EnergyWise Global Configuration Commands
epm EPM Global Configuration Commands
errdisable Error disable
ethernet Ethernet configuration
event Event related configuration commands
exception Exception handling
exit Exit from configure mode
fallback Fallback configuration commands
fhrp Configure First Hop Redundancy Protocols
file Adjust file system parameters
fips FIPS mode after next reload
flow Global Flow configuration subcommands
format Format the output
global-address-family Enter address-family base routing topology mode
help Description of the interactive help system
hostname Set system's network name
hw-module Apply command (e.g. shutdown) to specified
hardware target
hw-module Control of individual components in the system
hw-switch Control of individual components in the switch
id-manager ID Pool Manager
identity Identity Configuration Commands
infra-test Configure end2end properties
interface Select an interface to configure
ip Global IP configuration subcommands
ipc Configure IPC system
ipv6 Global IPv6 configuration commands
isis Global ISIS configuration subcommands
issu no description
key Key management
kron Kron interval Facility
l2 Layer 2
l2protocol-tunnel Tunnel Layer2 protocols
lacp LACP configuration
li-view LI View
license Configure License
line Configure a terminal line
link Enable Link State Tracking feature
lldp Global LLDP configuration subcommands
location Global location configuration commands
logging Modify message logging facilities
login Enable secure login checking
mab MAC Authentication Bypass Global Configuration
Commands
mac Global MAC configuration subcommands
macro Macro configuration
media-proxy Global media proxy configuration
mediatrace Mediatrace Application
memory Configure memory management
metadata Metadata Application
mka MACsec Key Agreement (MKA) configuration
module Module
monitor Monitoring different system events
mvr Enable/Disable MVR on the switch
netconf Configure NETCONF
Thank you.Hi,
QOS implementation has radically changed since the advent of
sup-7 & later
You no longer set mls qos as qos is on the engine by default.
Please see the following links
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-4500-series-switches/white_paper_c11-539588.html
"Ingress QoS: Default Actions
First and foremost, QoS does not need to be enabled on the Supervisor Engine, it is on by default in compliance with the MQC construct.
When a packet arrives at an interface, there are two options to take into consideration: is there a policy attached or not? If the packet arrives with or without a marking and there is not a policy attached to the interface, packets will flow through the switch untouched. There are no questions as to where the packet came from or if it has a valid marking. If the packet arrives with or without a marking, and a policy is attached to the interface, the packet will only then be subject to the policy classification."
And the config guide
http://www.cisco.com/c/en/us/td/docs/switches/lan/catalyst4500/15-1/XE_330SG/configuration/guide/config/qos_mrg.html#wp1461453
Hope this helps
Regards
Alex
Maybe you are looking for
-
Tasks not getting executed as per schedule
Hello Gurus, my query is with respect to tuxedo 7.1 / singleview 4.02.17.01. I am facing some new issues these days with singleview. Whenever we submit any task in singleview, it is not getting executed on its scheduled time. this has been happening
-
Is it possible to create the social networking site with adobe muse?
Where users can create their own pages with their self information
-
IDVD quits unexpectedly when launched
Brand new iMac which for some reason will not allow me to launch iDVD without 'quitting' The report error details something along the lines of 'library not loaded' 'image not found' Would be grateful of a fix for this problem
-
Hi, We have one plant it is a service plant we are providing only service from this plant now we are making this as sales and service, so for the sales materail can u give the steps or a link for MRP, we want automatic material requiremen
-
Hi, I've 1 main component and i sub component. The sub component contains a table. I use the sub component twice in the main component. The amount of visible rows have to be different for the 2 usages though. The way i figured, i created a method on