Y410p Front headphone and microphone jacks not working after repair

I recently (last month) sent  my IdeaPad Y410p in to Lenovo for repairs due to the laptop not turning on, or repeatedly restarting at the BIOS screen. The laptop was repaired by Lenovo (they replaced the motherboard), and returned it to me. The laptop has worked great sincce then, except that the two USB ports on the right side and the headphone and microphone jacks do not work. I have reinstalled the audio drivers, twice, but have not reinstalled the chipset drivers at all, as I don't want to screw around with those untiol I no more about what I should do. Any help would be appreciated.

Hi Talonek, welcome to the forums,
the problem you are experiencing is probably due to the cable connecting the ports on the right side, front of system, to the mainboard unfortunately not being connected or connected properly.  Please see pdf page 52 of the system's Hardware Maintenance Manual.
I've never taken an Y410p apart, but having looked at the manual the cable connection may well be accessible to check / fix by removing the hard drive.  Another alternative would be to call service and ask them to do this for you.

Similar Messages

  • My headphones speakers and microphone are not working please help

    hi i have had my hp windows 7 lap top for 2 years and never had a problme but recently my speakers and microphone are not working even if i put in my headphones i have installed new audio drivers checked my sound settings and did a restore to a date and a factory reset and still no sound ( my speakers say there working the geen bar goes up and down showing the volume but still no sound) please help me thanks

    Hi,
    Please use the following instructions to check and fix:
       http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01912228&cc=ad&dlc=en&lc=en&jumpid=reg_r1002_us...
    Good luck.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • How do I use a headset with separate headphone and microphone jacks on my macbook air

    I have a new macbook air and a headset with separate headphone and microphone jacks. Where (how) do I plug in the microphone jack into the computer?

    This adapter and sufficient length VGA cable is all you need.

  • Mic Jack not working after Driver Update, Console unavailable, can't install

    LMic Jack not working after Driver Update, Console unavailable, can't install? I've had nothing but problems after downloading the latest updates via the auto-updater.
    I'm currently using the Creative SB X-Fi Pro Series card. I've had it for close to 6 months and have not had any issues until I ran the auto-updater last night, and while it downloaded over 250Mb of updates, all of them failed to install as described below.
    I'm running on Windows Vista Ultimate, 64-bit
    My main issue is the fact that my microphone is no longer working. I've done a lot of searching and I think the problem has to do with flexijack not being a microphone jack, but instead is an 'in-line' jack. I can no longer find my audio control console, which allows me to switch between gaming and entertainment modes, ect. The solution I found on the KB says that you can switch the blue jack on the back of the card from an in-line jack to a mic jack within the Audio console. I tried downloading it, but while going through the install, I get an error saying the files could not be found and a prompt which asks for a disk or file location. The same thing pretty much happens with all of the items I attempted to download and install.
    I was able to run console fine, as well as use my mic yesterday before I attempted any updates. I attempted the updates because since I've had the card, I've had issues where after I exit a game, all my sound will become crackly and static. Before, I would simply open up the console and switch back-and-forth from gaming to entertainment, which would fix the problem most of the time. If that didn't work, a restart would fix it, but now I've opened up a whole new set of issues.
    Any help would be greatly appreciated.
    I also want to say that the support tickets should not require a serial number to submit a new ticket. My product is registered, so I got rid of the box which contains all that information, leaving me at the mercy of these boards...

    Hello all. Fisrt of all, this are my specs: Yoga 2 pro 13". WiFi card: Intel(R)Dual Band Wireless-AC 7260. I bought it from Best Buy on November 27, 2014. If you aquired your Yoga before this date, you may have the single band WiFi card. As many of you have experienced, I also had a bunch of issues with my WiFi connectivity and this is how I was able to solve it. At least it has been a couple of days that I haven't had any issues. The first symptom was the usual connection drops every X amount of time. For me it was about every 2 hours. I first unchecked the "Allow the computer to turn off this device to save power" option in the Power Management tab of device manager and disabled U-APSD support in the Advanced tab of device manager. This action did not solve the problem. I then downloaded and updated the driver from the Intel web site (http://www.intel.com/p/en_US/support/detect) and this seemed to solve the drops; however, a new problem arised: Everytime my Yoga would wake up from sleeping mode, all my wifi networks were gone and the adapter showed as disabled in Device Manager. I would have to anable it to have my networks back. It was a solution but a pain the butt to have to do this everytime. After hours of reading post after post in several forums, I read a repy from Lenovo asking to try leaving the "Allow the computer to turn off this device to save power" CHECKED if you were using the latest version of the driver. I went back to device manager and checked it back and that seems to have solved the problem. So far I haven't had any drops and everytime my laptop comes back from sleeping mode the WFi connection is still there! Here is a recap of how everything ended up: -The driver version I installed is 17.1.0.19-The driver date is 7/21/2014-In device manager|Advanced, U-APSD support is Disbled.-In device manager|Power Management, "Allow the computer to turn off this device to save power" is checked. Hope this helps somebody else.

  • My iMessage and facetime is not working after updating to ios 7... My ipad works perfectly and it's the same apple id.  Any answers or reasons why on the iPhone 5 is not working???

    My iMessage and facetime is not working after updating to ios 7...
    Any answers on how to fix it?  I've tried to restart, restore connected to itunes, but nothing.

    ACTIVATING FACETIME AND IMESSAGES
    Activating Facetime and Imessages on your phone requires the ability to send SMS messages and depending upon where you are that might be an international SMS.  Check with your carrier to see if your plan supports sending of international SMS messages.  If you are having trouble activating Facetime or Imessages turn them both off on your device and reset the device (Hold down the Sleep/Wake button and the home button together until the apple logo appears (ignore the ON/OFF slider) then let both buttons go and wait for device to restart (no data will be lost)).  Wait for the device to restart and wait a minute and turn Facetime and imessage back on and wait for activation.  If that does not fix things read the following articles:
    http://support.apple.com/kb/TS4268
    http://support.apple.com/kb/ts3367

  • The date and time is not working after setting it to current date and goes back to may,26 2011

    the date and time is not working after setting it to current date and goes back to may,26 2011; 2 PM . I bought my ipod tocuh 4th gen on july 18th

    On the iPod, make sure your Calendar is set to Gregorian (Settings > General > International > Calendar).  Also make sure your date and time on your computer is correct as well as the Time Zones on both.

  • HT201412 my ipod 4G power button and volume button not working after updated to ios6. i also experience wifi issue. so deppresing!

    my ipod 4G power button and volume button not working after updated to ios6.
    i also experience wifi issue. my ipod can't detect any wifi signal.
    so deppresing!
    what should i do?
    i can't put my ipod to sleep, can't adjust volume, can't shut off.
    should i update to ios 6.1?
    HELP

    Try:
    - Reset the iOS device. Nothing will be lost
    Reset iOS device: Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Reset all settings
    Go to Settings > General > Reset and tap Reset All Settings.
    All your preferences and settings are reset. Information (such as contacts and calendars) and media (such as songs and videos) aren’t affected.
    - Restore from backup. See:       
    iOS: How to back up
    - Restore to factory settings/new iOS device.
    -  Make an appointment at the Genius Bar of an Apple store.
    Apple Retail Store - Genius Bar
    When iOS 6.1 comes out I would update.

  • Speakers and microphone are not working

    suddenly, speakers, headphones and the microphone are not working...
    i tried updating the driver but it didn't work and when i try to test it through propertise i get an error message " failed to play test tone"
    what should i do?
    product: dv6-1350us
    product number: VM219UA#ABA
    win. 7 64-bit

    Hi eslam-hussien,
    Welcome to the HP Support Forums! 
    I can understand how frustrating it must be to have lost the sound from your speakers, headphones and the microphone has stopped working as well. I will try my best to help you with this.
    In this document for Troubleshooting Audio Problems with External Speakers, Headphones, and HDMI Sound Devices are steps for resolving this issue. 
    I hope this information helps, please let me know how it goes.
    Thank you and good luck!
    I worked on behalf of HP.

  • Microphone does not work after restarting computer

    I just received the Creative Xmod soundcard yesterday after using an Icemat siberia usb headset sound card for a couple months. The sound is a lot better with the creative soundcard however, if I restart my computer and go back into ventrilo, my microphone does not work. It doesnt make any sound when I talk into it (almost as if it muted itself) but it hasnt. I check my sound settings and everything is the way it should be.....but the mic isnt producing any sound. It is not my headphones that is causing the problem because I have never had this problem with my old icemat soundcard. I am currently using :
    Sennheiser PC350 headset
    Windows XP Home Edition
    The newest version of Ventrilo

    http://picsend.net/images/240403ventsetup.JPG
    That is how I have ventrilo setup. A friend of mine said I should Mux set to Record Control, but it only gives me the option for Wave In =/

  • My Microphone is not working after upgrading to Windows 7 using Laptop Satellite L505D-S5965

    Please I need your help. My laptop Satellite L505D-S5965 had vista and I got the upgrade for windows 7. However after the upgrade I noticed that the microphone is not working while the speaker are working fine. I have went to the sound right click and choosed recording device and found tha the realtalk is my driver and everything is fine there. when I change to stereo mix I got very bad noise.
    can someone help please. please note that the microphone was working in vista operating system. Does Windows 7 has a bug in this regrad.
    I also have another question my understanding is the model Satellite L505D-S5965 has no internal microphone is this is the case? I can plug in external mic into the jack provided for this but there is no built in microphone am I correct please advise?
    thank you for all you great help

    Hi
    when you upgrade the operating system to windows 7 it just install the generic driver
    copy and paste the link
    http://cdgenp01.csd.toshiba.com/content/support/downloads/driver_audio_realtek_TC50036500C.exe
    let me know if it didnt work

  • Office 2010 MUI in Finnish and Save and Send function not working after upgrading to Lync 2013 MUI

    Problem is as follows. Used to have Office 2010, Outlook 2010 and Lync 2010, everything was working. People used it in Finnish and seemly quite a many of them used the Talleta ja lähetä (Save and Send in Finnish) in Office products.
    After upgrading Lync to 2013 version, with Finnish language pack installed with it, the Save and send does not work in Office 2010 if it is used with Finnish as display language. When you try to use it you get a Mapi error and reason is undefined or something,
    hard to say what it is exactly in english as the error message is in finnish. On those machines if the display language is changed back to english the Save and send works as it should.
    Any ideas? 

    The problem was caused by the Language Packs for Lync 2013 or Office 2013. Without them all works.
    And if you want to just unisntall the 2013 lang packs, then you also need to repair install the office 2010 ones to make it work again.

  • Illustrator CC 2014 open and place commands not working after installing Yosemite

    How can I get Illustrator Open and Place commands to work after installing Yosemite?

    Hello,
    I also have the same problem, after 5 minutes I can't open or place anything in illustrator. I have this problem also in photoshop cc 2014. This started after installing Yosemite.
    Tried to reinstall but nothing helps.
    Today after updating creative cloud application it is even worse: illustrator is not opening anything: not even a new file. So I reinstalled... and I can open again for 5 minutes. But then it crashed while saving. Now I can't open illustrator at all...so nothing left to do then reinstalling again I suppose?

  • Touchsmart 520-1047c Mouse and Keyboard will not work after sleep mode

    I have an issue which I need some help with. When my computer goes to sleep the wireless mouse and keyboard will not work unless I restart, however each one will wake the system up but will not operate after that. I have tried just making the display go to sleep, both go to sleep but that makes no difference same issue occurs. The only work around I have found is going into the power settings and turning the sleep mode off for booth the computer and display. This does not solve the problem it just masks it. New batteries, unplugged and replugged the dongle, updated the bios and all drivers. Don't know what else to try. Anybody know how to fix this? Thank you in advance for your help.

    Hello , Welcome to the HP Forums, I hope you enjoy your experience! To help you get the most out of the HP Forums I would like to direct your attention to the HP Forums Guide First Time Here? Learn How to Post and More. I understand that the mouse and keyboard on your desktop computer does not work if your computer enters sleep mode, and I would be happy to assist you in this matter! To correct this issue, I recommend following the steps in this document on Troubleshooting sleep and hibernate issues (Windows 7). This should help enable your system to wake from sleep mode using your wireless keyboard and mouse. I also recommend connecting wired peripherals to diagnose the functionality of your keyboard and mouse. If your system is still not able to wake from sleep mode, please follow the steps below to restore the default power schemes on your computer: Step 1. Click the Start button
    Step 2. In the search box, type "Command Prompt"
    Step 3. Right-click Command PromptStep 4. Click Run as administrator
    Step 5. At the command prompt, type powercfg /restoredefaultschemes and press Enter  reference: http://superuser.com/questions/669571/windows-8-1-64-bit-power-schemes-gone Please re-post with the results of your troubleshooting, as well as the requested information above. I look forward to your reply!
    Regards  

  • System sleep and shut down not working after upgrade to windows 10

    HiI upgraded my OS from win 8.1 to win 10.After the upgrades the system shutdown and sleep are not working properly.It's like when I shutdown/sleep the system ,the screen shuts down but the power key keeps glowing and also the battery keeps draining.So eachtime I have to foercefully press the power button to shutdown the system. I have updated the display driver . Please someone  suggest, what to do ?

    Hi there ,  Thank you for visiting the HP Support Forums and Welcome! I read your post on the HP Support Forums and seen that you are having issues with your HP Pavilion 15-n260tx Notebook PC and the Sleep/Shut down options. It sounds like you might be having an issue with one of the features of Windows called Hybrid Shutdown that is used for the Fast Startup feature.  Here are a couple of links for you about Fast Startup, Hybrid Shutdown and How to Shut down your Notebook completely. They also have some troubleshooting steps in them.   1. Fast Startup - Turn On or Off in Windows 10.2. Shut Down Computer in Windows 10. If those do not work, I do have some more documentation for you to read and try.  1. Shut down (turn off), sleep, or hibernate your PC - This document is from Microsoft. 2. HP Notebook PCs - Managing Power Options (Windows 8)3. HP PCs - Sleep and Hibernate Issues (Windows 10, 8) Sometimes a BIOS Update will work. You can update all of your drivers by going to the HP Driver's website or by using the HP Support Assistant. On the Driver's page there is not an update for the Windows 10 Column, but there was an update that just came out under Windows 8.1 on Aug 7, 2015 that should work for your Notebook.  Another fix that may work is to Run the Troubleshooter. Please follow this link to run the Windows Update Troubleshooter.   I hope this helps!  Have a great day!

  • CFHTTP and Scheduled Tasks not working after CF8 Upgrade

    I have recently upgraded to ColdFusion 8. My scheduled tasks
    in the ColdFusion Administrator do not work anymore. I ran them
    manually without the ColdFusion Administrator from the server and a
    local machine via Internet Explorer 7 and they work. I tried to run
    the same scheduled task with the same URL via CFHTTP in a CFM page
    and this does not work. The logs are not giving me any error
    messages. Has anyone run into this? Is this a bug with CF8 or even
    an IIS issue? ColdFusion is on a Windows 2003 SP2 server.
    Thanks,
    Mike

    <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
    <HTML dir=ltr><HEAD><TITLE>The page cannot be displayed</TITLE>
    <STYLE id=L_defaultr_1>A:link {
    FONT: 8pt/11pt verdana; COLOR: #ff0000
    A:visited {
    FONT: 8pt/11pt verdana; COLOR: #4e4e4e
    </STYLE>
    <META content=NOINDEX name=ROBOTS>
    <META http-equiv=Content-Type content="text-html; charset=UTF-8">
    <META content="MSHTML 5.50.4522.1800" name=GENERATOR></HEAD>
    <BODY bgColor=#ffffff>
    <TABLE cellSpacing=5 cellPadding=3 width=410>
      <TBODY>
      <TR>
        <TD vAlign=center align=left width=360>
          <H1 id=L_defaultr_2 style="FONT: 13pt/15pt verdana; COLOR: #000000"><ID id=L_defaultr_3><!--Problem-->The page cannot be displayed
    </ID></H1></TD></TR>
      <TR>
        <TD width=400 colSpan=2><FONT id=L_defaultr_4
          style="FONT: 8pt/11pt verdana; COLOR: #000000"><ID id=L_defaultr_5><B>Explanation: </B>There is a problem with the page you are trying to reach and it cannot be displayed.</ID></FONT></TD></TR>
      <TR>
        <TD width=400 colSpan=2><FONT id=L_defaultr_6
          style="FONT: 8pt/11pt verdana; COLOR: #000000">
          <HR color=#c0c0c0 noShade>
          <P id=L_defaultr_7><B>Try the following:</B></P>
          <UL>
            <LI id=L_defaultr_8><B>Refresh page:</B> Search for the page again by clicking the Refresh button. The timeout may have occurred due to Internet congestion.
    <LI id=L_defaultr_9><B>Check spelling:</B> Check that you typed the Web page address correctly. The address may have been mistyped.
    <LI id=L_defaultr_10><B>Access from a link:</B> If there is a link to the page you are looking for, try accessing the page from that link.
          </UL>
          <HR color=#c0c0c0 noShade>
          <P id=L_defaultr_11>Technical Information (for support personnel)</P>
          <UL>
            <LI id=L_defaultr_12>Error Code: 400 Bad Request. The data is invalid. (13)
            </UL></FONT></TD></TR></TBODY></TABLE></BODY></HTML>

Maybe you are looking for