Creating multiple tasks

I am using the CVI plug-in for MSVC. My application requires that I toggle a set of digital lines based on a user's input. For a variety of reasons I would like to initialize my DAQ task handles at the start of the program so that when I need to toggle the lines I just call Run and Stop.
Some of my tasks use the same lines. I know that if I try to define multiple tasks using the same lines that I will get an error (-200089).
My question is this: Is there a clever way to pre-define my tasks at the start of the program even if they use the same lines?
Thanks.

UGH! Cut and paste got me. Stupid syntax error. I can do what I wanted to do.

Similar Messages

Creating multiple tasks in labview fpga

Hi,
I need to create multiple tasks in labview fpga....I need to set one update period in each task so that i can make my while loop run at this rate everytime my input frequency changes....How do i do this?

Hi,
just to be sure: You are talking about multiple tasks on the FPGA to acquire data? Or do you want to have multiple tasks on the host to display the data?

Create Multiple tasks for Single Item in List using state machine workflow in sharepoint

Hi,
I want to create multiple create tasks for Single Item in List based on Assigned to column using state machine Workflow through visual studio
Here Assigned to column allows multiple users. so i have to create task for every user based on column .
I'm trying for this but i didn't got any solution
Please provide solution for this.

Hi,
According to your post, my understanding is that you wanted to allow multiple users to approve.
There are some articles about creating parallel tasks in state machine workflow, you can have a look at them.
http://www.codeproject.com/Articles/477849/Create-Parallel-Task-in-State-Machine-Workflow-in
http://msdn.microsoft.com/en-us/library/office/hh128697(v=office.14).aspx
http://social.technet.microsoft.com/Forums/office/en-US/b16ee858-4360-479a-a686-4ee35b7be9db/sharepoint-2010-workflow-creating-multiple-tasks?forum=sharepointdevelopmentprevious
Thanks & Regards,
Jason
Jason Guo
TechNet Community Support

Creating multiple tasks depending on field responsible

I would like to create one task which has
multiple charges.
The system should createa task for each
person who is in charge.
Is there abuilt-in function?
should I use designer ?
Nikita

Based on your description, my understanding is that you want to create a task which has multiple charges.
Refer to the following steps:
    Prepare the needed components
       1.1
Create Site Collection
       1.2 Activate SharePoint Server Enterprise Site Collection Features.
       1.3 Create the needed users
2.      Build the leave requests SharePoint list
3.     Build InfoPath form
       3.1 Create the needed controls and views
       3.2 Disable enable controls according to current state
      3.3 Validation and submitting the leave request
4.    Build SharePoint designer workflow
       4.1 Building the logic
      4.2 Adding tasks assignment, email notifications and History
For more detailed steps, refer to the following article:
http://jamilhaddadin.com/2011/12/03/implementing-workflow-using-infopath-2010-and-sharepoint-designer-2010/#4
Best Regards,
Lisa Chen
Lisa Chen
TechNet Community Support

Create multiple Task Instance from one Task Instance

We have a process, where user can request for multiple resources(access) in one single request.Currently user has to wait until all the resource requests are approved by application owners to start the provisioning process.
I am thinking of splitting that one request(task) into multiple task, based on the number of resources requested.so that, if one resource request is approved user can get that particular access.
My question :
1.How will I split the one task into multiple task and pass the required information to child task?
2.How do I handle views?Currently since its one task , we checkout and check-in the same view.
3.How will I overcome the possibility of one view overwritten by the other.
Thanks.

We have a process, where user can request for
multiple resources(access) in one single
request.Currently user has to wait until all the
resource requests are approved by application owners
to start the provisioning process.
I am thinking of splitting that one request(task)
into multiple task, based on the number of resources
requested.so that, if one resource request is
approved user can get that particular access.
My question :
1.How will I split the one task into multiple task
and pass the required information to child task?
2.How do I handle views?Currently since its one task
, we checkout and check-in the same view.
3.How will I overcome the possibility of one view
overwritten by the other.
Thanks.Hi,
yes u can split one task into multiple task means as ur requirment diffrent task for different resource. so u have to write diffrent W/F for each resource and call them by setting a counter for number of resource.
the below code help u.
<Variable name='index'>
 0
 </Variable>
<Activity id='1' name='createNewTask'>
 <Action id='0' name='createView' application='com.waveset.session.WorkflowServices'>
 <Argument name='op' value='createView'/>
 <Argument name='type' value='Process'/>
 <Argument name='viewId' value='Process'/>
 <Argument name='taskName'>
 <s>give any name to the task</s>
 </Argument>
 <Argument name='process'>
 <s>task name that u want to launch</s>
 </Argument>
 <Argument name='accountId' value='$(accountId)'/>
 </Action>
 <Action id='1' application='com.waveset.session.WorkflowServices'>
 <Argument name='op' value='checkinView'/>
 <Argument name='view'>
 <ref>view</ref>
 </Argument>
 </Action>
 <Action id='2'>
 <set name='view'>
 <null/>
 </set>
 </Action>
 <Transition to='incrementIndex'/>
</Activity>
 <Activity id='2' name='incrementIndex'>
 <Action id='0'>
 <set name='index'>
 <add>
 <ref>index</ref>
 1
 </add>
 </set>
 </Action>
 <Transition to='createNewTask'>
 <lt>
 <ref>index</ref>
 <ref>length</ref>
 </lt>
 </Transition>
 <Transition to='end'/>
 </Activity>

Procedure to create multiple tasks

hi gurus,
             What is the procedure to create the multiple steps taks in workflow and tcode for that.

no i mean in workflow we have 2 types of tasks
1- single step tasks.
2-multiple step tasks.
single step tasks which we create normally.so i want to know how to create the multiple step tasks.i heard that we need to start with-
1.      In the UWL view, choose New Task.
2.      Select Multiple Steps from the Task Type dropdown list.
3.      Under Subject, enter a title for the task.
4.      Choose Add Step.
                                      Here iam unable to get the step 1.please could you tell me the exact procedure.

OVI Suite creating multiple tasks

I have "upgraded" the PC Suite software on my Windows 7 laptop to Ovi Suite 2.0.1.35 and now every time my phone syncs, any recurring tasks are created for the next 6 months and the recurrences are screwed up so that I have to reset everything manually. Initially I had 2000 tasks created as it created new entries for the next 20 years. I could then not remove them from the phone as there was no available memory. I have now got this down to about 56 tasks when there are only 28 in my Outlook (2007) file, but this can change between syncs. It has also screwed up a couple of Contacts email addresses, but nowhere near as badly as my tasks.
Is this a known issue with the software? Frustrating as hell. There were never these kinds of problems with the "old" software!
And also, is there a way to syncronise the Calendar and not the tasks? That would fix my problem but they are under the same option.

I have the same problem. I use E51 and the same version of Ovi Suite. It created thousends of task.
Here are the application and system details:
Nokia Ovi Suite 2.0.1.35
Nokia PC Suite 7.1.30.9
PC Connectivity Solution 9.39.0.0
Connectivity Cable Driver 7.1.20.0
Nokia Ovi Suite Software Updater 2009.40.0.60128
Maps Service API 3.0.35.0
Nokia mPlatform 2.5.195
Ovi Desktop Sync Engine 1.0.0.684
Operating system:
Microsoft Windows XP 32 bites kiadás, Service Pack 2
Language: English
Internet browsers:
- Microsoft Internet Explorer 6.0.2900.2180
- Mozilla Firefox 3.5.5 (Default)
Bluetooth version:
- Microsoft (Version: 5.1.2600, build: 2180)

CHaRM-Is that possible to create multiple Transport Request in UC

HI Gurus,
Quick question on ur.gent correction using Solution Manager CHaRM in EHP1. Is it possible to create multiple transport request(TR) for single ur.gent correction (UC). DO NOT confuse with transport task.
For example, after I created transport request and developer start working and release the task, realised to add another transport request for same UC. When I tried, it did not create any TR but checked the message found that
Schedule Manager: Monitor
Job Status: Processing completed, but with warnings
Program Name: /TMWFLOW/SCMA_TRORDER_CREATE
Action to be checked: Ur.gent Correction: Create Transport Request
There is already an open request, XXXXXXXXXX, for this project
So only way I can do that I released the TR and able to create another TR.
May be wondering why I need to create another TR, why not create TASK and work on that.
But this is the requirement at our company.
I will appreciate the effort and time to provide me the solution of this.
Thanks
Ava

Hi Ragu,
That's really quick turn around. Unfortunately not able to found whatever you mentioned in your message. Here is detail,
I navigate to Actions - Depending on Status, found the entry as
Trans. Type     StatProf         UserStatus     Seq     Action in SAP Change Manager
SDHF             SDHFHEAD   E0002            10       CREATE_HF
SDHF             SDHFHEAD   E0002            20       CREATE_REQ
SDHF             SDHFHEAD   E0002            30       SAVE_PARTNER
SDHF             SDHFHEAD   E0002            40       SET BO LINKS
Where SDHF - Ur.gent Correction
           E0002 - In Development
           CREATE_HF -        Create an Instance in SAP Change Manager
           CREATE_REQ -     Create Transport Request with Task
           SAVE_PARTNER - Save Partners in Respective Partner Roles
           SET BO LINKS -     Sets Links to Business Objects
I don't see any OPEN_TR.
Any other place need to make change.
Thanks
Ava

Mx-DAQ multiple tasks

Hello,
Im using LV7.1 with NI-Daq 7.4.
in my Application i use multiple tasks, a few for aquiring analog and digital input from my first 6024E and one to aquire digital input from my second 6024E.
In most of the time this works very well, but from time to time, when the mxdaq read VI for the second task is executing for the first time, an error message occurs. This erromessage tells me, that i passing an empty string instead of an task reference to the mxdaq read VI of my second card. After Reexecuting my App it works fine without creating error messages until I reboot. For me it looks like an initialization/synchronization problem. Both cards are properly installed and visible/testable in MAX.
For syncroniziation of these cards i use the same MX-DAQ clock source.
Perhaps i have to reconfigure the task initailization but i dont know what is wrong.
thank for help

I'm guessing that the reason that you only see this sometimes is that it is a race condition between the read call and task creation. I've seen this problem before and the cause is usually that you are trying to read before your task is created. This can be caused by using an asynchronous process to create your channels/tasks apart from doing your multi-channel reads. To eliminate this problem I suggest you write your application in such a way that you create all of your tasks first, before trying to read from any of them. The easiest way to do this is to wire up your create task VI's in order before your reads, as these VI's will block until they complete task creation.
Hope this helps,
DB

Create multiple rule in single alert category

Hi All,
any body tell me can we create multiple rule in single alert category.When i click on a add rule button in existing category nothing will happen same page will come with existing data.
Thanks & Regards
Samarjit

HI,
you can define alert category multiple rules.. see the below links
http://help.sap.com/saphelp_nw2004s/helpdata/en/bb/f0033c128f4a7de10000000a114084/content.htm
http://help.sap.com/saphelp_nw2004s/helpdata/en/45/23827054604aa8e10000000a11466f/content.htm
You must define the binding from the task container to the rule container for each rule. For further information, refer to Rule Resolution
http://help.sap.com/saphelp_nw2004s/helpdata/en/c5/e4b5aa453d11d189430000e829fbbd/content.htm
Regards
Chilla

Script for InDesign CS6 - create multiple, prenamed layers

I created a script for Illustrator CS6, in ExtendScript Toolkit, that will create multiple, prenamed layers...see below...
//Apply to myDoc the active document
var layerName = LayerOrderType;
var myDoc = app.activeDocument;
//define first character and how many layers do you need
var layerName
var numberOfLayers=0;
//Create the layers
for(var i=0; i<=numberOfLayers; i++)
{ var layerName = ":: GRADIENT"; var myLayer = myDoc.layers.add(); myLayer.name = layerName; }
{ var layerName = ":: STRIPES"; var myLayer = myDoc.layers.add(); myLayer.name = layerName; }
{ var layerName = ":: LEGAL"; var myLayer = myDoc.layers.add(); myLayer.name = layerName; }
{ var layerName = ":: BLK BAR"; var myLayer = myDoc.layers.add(); myLayer.name = layerName; }
{ var layerName = ":: FLAME"; var myLayer = myDoc.layers.add(); myLayer.name = layerName; }
{ var layerName = ":: LOGO/TYPE"; var myLayer = myDoc.layers.add(); myLayer.name = layerName; }
{ var layerName = ":: TRIM,ETC"; var myLayer = myDoc.layers.add(); myLayer.name = layerName; }
{ var layerName = ":: LOEC INFO"; var myLayer = myDoc.layers.add(); myLayer.name = layerName; }
// Moves the bottom layer to become the topmost layer
if (documents.length > 0) {
countOfLayers = activeDocument.layers.length;
if (countOfLayers > 1) {
bottomLayer = activeDocument.layers[countOfLayers-1];
bottomLayer.zOrder(ZOrderMethod.BRINGTOFRONT);
else {
alert("The active document only has only 1 layer")
I tried to use this exact code to replicate the same scenario in InDesign but it doesn't work.
Can anybody help me out!?
Thanks in advance

Marijan Tompa's scripts are very nice and useful, however, for this simple task you can try create your own wiht this code:
app.activeDocument.layers.add ({name: "GRADIENT", layerColor: UIColors.red});
app.activeDocument.layers.add ({name: "STRIPES", layerColor: UIColors.lightBlue});
app.activeDocument.layers.add ({name: "LEGAL", layerColor: UIColors.gray});
//merge existing document layer to bottom layer (in this case original layer will be merged to 'GRADIENT')
var myDocument = app.documents.item(0);
var myLayerA = myDocument.layers.item(2);
var myLayerB = myDocument.layers.item(3);
myLayerA.merge(myLayerB);
alert("Layers created!");
assume, your document has one layer.
Script creates three new layers, they appear in Scripts palette in this order:
LEGAL
STRIPES
GRADIENT
and merges 'old' layer to bottom layer of newly created set (GRADIENT).
sure, you can add as much layers as you need, just don't forget modify LayerA and LayerB numbers accordingly.
Or disable second part of the script at all, if you don't want anything to be merged.

How to create multiple new rows in ADF Table?

Hello,
being new to ADF Faces/BC I managed to display data in an ADF Table and create new entries using the "CreateInsert" operation (one at a time).
Now, the next task is to create multiple new rows at the same time, set some default values and display the new rows in the ADF table. Then the user will enter additional data and commit the new rows.
Where do I step in? In the EntitiyImpl? Can this be handled declaratively or do I have to implement custom method(s) in the AM?
Thanks
Gerald

Hi John,
I'm still getting the following error
Error(94,144): method getValue() not found in class javax.faces.el.ValueBinding
What should it be casted to?
The code in backing bean is like this..
package view.backing;
//import com.test.model.TestAppModuleImpl;
import javax.faces.component.html.HtmlForm;
import javax.faces.component.html.HtmlPanelGroup;
import javax.faces.context.FacesContext;
import javax.faces.event.ActionEvent;
//import javax.faces.event.FacesListener;
//import oracle.adf.model.BindingContext;
import oracle.adf.model.binding.DCBindingContainer;
import oracle.adf.model.binding.DCIteratorBinding;
import oracle.adf.view.faces.component.core.data.CoreColumn;
import oracle.adf.view.faces.component.core.data.CoreTable;
import oracle.adf.view.faces.component.core.input.CoreInputText;
import oracle.adf.view.faces.component.core.nav.CoreCommandButton;
import oracle.adf.view.faces.component.core.output.CoreMessages;
import oracle.adf.view.faces.component.html.HtmlBody;
import oracle.adf.view.faces.component.html.HtmlHead;
import oracle.adf.view.faces.component.html.HtmlHtml;
import oracle.jbo.ApplicationModule;
import oracle.jbo.Row;
import oracle.jbo.ViewObject;
//import oracle.jbo.server.ViewObjectImpl;
//import view.utils.EL;
public class MultipleInsert1 {
private HtmlHtml html1;
private HtmlHead head1;
private HtmlBody body1;
private CoreMessages messages1;
private HtmlForm form1;
private CoreTable table1;
private CoreColumn column1;
private CoreInputText inputText1;
private CoreColumn column2;
private CoreInputText inputText2;
private CoreCommandButton commandButton1;
private HtmlPanelGroup panelGroup1;
private CoreCommandButton commandButton2;
public void setHtml1(HtmlHtml html1) {
this.html1 = html1;
public void createMultiRows(ActionEvent actionEvent) {
DCBindingContainer dc = (DCBindingContainer) FacesContext.getCurrentInstance().getApplication().createValueBinding("#{bindings}").getValue();
DCIteratorBinding iter = dc.findIteratorBinding("TestView1Iterator");
ViewObject vo = iter.getViewObject();
for (int i=1; i<=5; i++) {
Row newRow = vo.createRow();
newRow.setAttribute("Id", i);
ApplicationModule am = vo.getApplicationModule();
am.getTransaction().commit();
vo.executeQuery();
Do I need to import something else?
Thanks,
Shri.

Creating customized Tasks

Hi I was wondering how one can create cusomized tasks through wlpi. Basically, We have some additional data related to a task which wlpi TaskInfo does not? I was wondering if there is a way to create subclass of TaskInfo and ask wlpi to instantiate that subclass when a new task is created?Also, How can we change attributes like task comments during run-time?Any help in this direction is appreciated.ThanksGurb

Hi,
You can also add multiple users to the same task / use book of business to restrict visibility to desired set of users. Not sure whether it makes relevance to your question :-)
-- Venky CRMIT

Creating Multiple Resource Objects for OOTB Connectors

All,
I am trying to create a second AD User resource object for the OOTB connector. I would like to think that the AD Connector (and all connectors, for that matter) was designed to handle the creation of multiple Resource Objects for the same Resource Types, but am I wrong? It doesn't seem like the OIM Connector can handle this easily.
Has anyone created multiple resource objects for a connector? Is this a fairly simple task, or will it require a large effort? Is it even possible? Any pointers?
Thanks!

I will provide a little help with the duplication. I found the best way to do it is to import the original connector. Go through the different pieces making each one have a unique name, that is not part of any of the other piece names. You need to have unique names for the following:
1. Resource Object
2. Process Definition - Provisioning
3. IT Resource
4. Form - Process
5. Scheduled Task
After you import the connector, rename each of the following to something unique. I would also update your process form to have a default value of your IT Resource, as well as your scheduled task values to point to the new unique names. Export the 5 items, no dependecies. The adapters will all be the same. Use find and replace for the values and then import the new XML. If it works, duplicate the XML for each of the new workflows you want to create.
-Kevin

Creating multiple user tables using script

hi
my requirement is i want to create multiple tables by running script . is it possible .how do i do that can any one suggest me and send sample code to solve this task.
(i have to create 100 userTables it is very difficult to create using code or from B1 that is my requirement )and i think some good solution is there for my problem and inserting the tables into B1 by running script.

Hi Om,
Take a look at the SDK help files, or even better, the examples provided with the SDK, they give you a good example how to create a usertable.
Tried that, you could programm a loop wich creates your usertables, or a function that progresses a input file containing all your usertables.
Pseudo code loop (C#)
for(int i = 1; i <=100; i++)
/* Call you your function that creates a usertable with the given name */
CreateUserTable("TBL_" + i.ToString());
Hope it helps,
Rowdy

Creating multiple tasks

Similar Messages

Maybe you are looking for