HP psc 1610 All-in-one ERROR

Dear reader,
My HP psc 1610 won't work anymore, if it even bothers to turn on I get the following message: ERROR:0xc0620004 411:lib_micci2.c
Does anybody know what could possibly wrong withe the machine? It used to work well, i didn't trow on the ground or something, (yet)
Thank you in advance,
Kind regards.

Hi - Follow the steps to reset the product, located in this document. Hopefully that will resolve the issue. If not, the printer will likely need to be serviced or replaced.
Hope that helps.
Say Thanks by clicking the Kudos thumbs up. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
I am an HP employee.

Similar Messages

PSC 1610 All-in-One error:0x880f253c

I'm getting an error message and cannot print. The printer starts to print then stops, tells me that the print job failed then tries to start again and stops. I get an error message on the printer display panel error:0x880f253c. After I've cancelled the print job and shut off the printer the error message appears a couple of times and I have to shut it off again. I've tried unplugging it for a minute and plugging it back in but still get the same error message. How can I fix this? Thanks.

It looks like you've done what is recommended to resolve that error. See the document listed below:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00489814&tmp_task=solveCategory&lc=en&dlc=en&cc...
The only other thing it mentions is to removed the cartridges first, then disconnect the power cord.
If that doesn't take care of it, it looks like it will need to be serviced. Wish I had better news.
Say Thanks by clicking the Kudos thumbs up. Please mark the post that solves your problem as an Accepted Solution so other forum users can utilize the solution.
I am an HP employee.

Can I share HP PSC 1610 All-In-One series printer through Bonjour?

I have an iBook G4, and a Mac Mini (10.4.11- Tiger) with a HP PSC 1610 All In One series printer connected to it by USB. On my iBook G4, the printer comes up under Shared Printers in the Printer Setup Utility but when I click on it, and press Show Info it freezes.. so I was wondering, is there a way to connect to the printer wirelessly with the correct driver (because the driver doesn't show up in the driver list... and the driver is installed.)

Hi my printer psc 1610 hp not picking paper

Paper Jam for HP PSC 1610 All-in-One Printer

Paper Jam for HP PSC 1610 All-in-One Printer:
I had a paper jam and cleared the paper from the printer. Now every time I turn the printer "on" it picks up the top piece of paper from the tray and runs it about ½ to ¾ of the way thru the paper feed, stops, and then displays message "paper jam clear paper and then press OK". When I do that it simply picks up the next piece of paper off the tray and does the message again. If I push the OK button on the printer it will simply finish the ejection and then pick up the next paper from the tray, and do the same thing. I have examined the interior (and exterior) of the printer for paper scraps and any other obvious sign of trouble (dirty drive wheels, missing rollers, broken springs, etc...) and can not see anything unusual. I can not print a test print because of the paper jam message. I am running Windows XP and the printer has been working fine for months (until this recent jam). I did all the steps from the HP fix it site including clean rollers, plug and unplugged, carriage travel OK and more. Don't know what to do now........Any help would be great!!!! Thank you!

Hi my printer psc 1610 hp not picking paper

HP PSC 1610 All-In-One doesn't see that paper is loaded

HP PSC 1610 All-In-One doesn't see that paper is loaded and keeps asking me to load paper and press OK. I have done that per manual with no success. What's going on?
I am using an Intel MacBook running SnowLeopard

OK, I think this was among a series of "recalled" (years ago) printers where the feed rollers would become coated with a very slick substance that was outgassing from the rubber. There was a cleaning kit made for this but I am not sure it is still available. Instructions for it are here.
It the absence of the kit, you can clean the rollers manually by removing the rear door and scrubbing the three rollers with Scotchbrite. Red was used in the kit, but green may be aggressive enough to do the job. You may have to fiddle with the printer to clean the entire circumference of the three rollers. Once you do this, you will be good to go for years to come!
Say thanks by clicking "Kudos" "thumbs up" in the post that helped you.
I am employed by HP

Psc 1610 all-in-one

Can I e-print to my HP PSC 1610 all-in-one?
This question was solved.
View Solution.

Hi JudithAMorrison,
Just to add some extra clarification for you, your PSC 1610 is not able to ePrint, as it was released before HP applied the ePrint technology to their printers. Generally any of the new printers are ePrint capable, so if you are wanting to acquire an HP ePrint enabled printer you can contact HP Tech Support at 1-800-474-6836 and see what sort of deals they have to get you an ePrint enabled printer.
If you need anything further please let me know. Have a great day!
Please click “Accept as Solution ” if you feel my post resolved your issue, as it will help others find the solution faster
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
**MissTeriLynn**
I work on behalf of HP

HP PSC 1600 All-In-One error message remove and replace color cartridge

I get the remove and replace color cartridge and printer or scanner won't work. I have replaced the cartridge with new ones twice and it still happens. Just installed a new HP color cartridge and no luck. I've tried everything I can think of.
Please, does anyone have any other suggestions????
Thank you,
Mary Jean Kelso

Hi MJKEL,
Welcome to the HP Forums.
I see that you are having an issue with errors on the printer pertaining the ink cartridges.
I do have a few steps that we can try in the attempt to troubleshoot this issue.
First off, please make sure that you have the printer power cable connected directly to a wall outlet and not a power bar/strip. Here is a document that uses a LaserJet printer as an example but it is meant for HP products in general. Please click on the following link that explains the Issues when Connected to an Uninterruptible Power Supply/Power Strip/Surge Protector.
I have also located a documet that deals with A 'Remove and Check [color / black / photo] Cartridge' Error Message Displays on the Printer Control...
Please feel free to write me back if you have any other questions or concerns.
Cheers,
Click the “Kudos Thumbs Up" at the bottom of this post to say “Thanks” for helping!
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
W a t e r b o y 71
I work on behalf of HP

1610 all in one printer

My computer is a Gateway GT4024 connected to my 1610 printer via a USB port. My wifes computer is an HP750N and is NOT commected to the printer with a cable.. Both operate on an XP platform. We have a LINKSYS wireless router and both computers have a wireless card. Until last week, both of us could send files to the printer and would print successfully. Now my wife can still print from her computer but I cannot. When I right click on the printer icon and open all printers and faxes, I see where the file I want to print is in the queue but somehow it's not going to the printer to be printed. I tired to print from my computer from WORDPAD but no success. I've reinstalled the software, disconnected the printer for 5 seconds, restarted my computer...still no printing from my computer but we can still print from my wifes computer...any suggestions of what I might try???

Hi @ContraMoros ,
Thank you for visiting the HP Support Forums and Welcome. I have read about your HP PSC 1610 All-in-One Printer and not having Software installed for your Mac 10.8 system. Your Mac would automatically install any software or drivers needed to operate the printer.
If the printer is not starting up there could be an issue with the wall outlet or the adapter. Here is a document on troubleshooting the printer not coming on.
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

How can I fix a check paper error on the HP psc 1210 all in one printer?

Product name/number: HP PSC 1210 all-in-one
OS: Windows 7
Error Msg: Check Paper light flashes
I have verified there are no paper jams, paper is loaded, print cartridges move freely and rollers are clean. Is there a a paper out switch that can fail?

Hi there,
This article should cover the issue you are experiencing. Give the steps outlined a shot and let us know if it helps.
Best of Luck!
You can say thanks by clicking the Kudos Star in my post. If my post resolves your problem, please mark it as Accepted Solution so others can benefit too.

HP PSC 2355 all-in-one Paper Jam Error

Hi. I have an HP PSC 2355 all-in-one printer that has worked well for a long time but when i switched it on today to do some printing, it made some strange noises and when i tried to print it sent an error saying there was a paper jam - but there was not !
It feeds a sheet of paper in about half way through then stops and the error is displayed.
I tried doing a copy, and the exact same thing happens.
Has anyone got an idea what has gone wrong ?
Thanks.

Make sure to follow all steps here:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c00212225&cc=au&dlc=en&lc=en&product=422000&tmp_...
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

Hp psc 1210 all in one printer feeding error

I have a model 1210 all in one printer and it will not feed paper. it sounds like something its working, but not gripping the paper. PLEASE ADVISE

Hello @anne0701 , and welcome to the HP Forums!
I can see you're experiencing paper feed issues. I would like to help!
I would recommend performing a power reset. Disconnect the power cord from the printer and the power outlet, then wait 60 seconds. After 60 seconds, plug the printer back in. Ensure you plug the printer directly to a wall outlet. Make sure to bypass any sort of surge protector or power bar.
I would also suggest following the steps in this video on PSC feed issues:
Fixing Paper Pick-Up Issues - HP PSC 1200 All-in-One Printer
Good luck and please let me know the results of your troubleshooting steps. Thank you for posting on the HP Forums!
Please click “Accept as Solution " if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the right to say “Thanks" for helping!
Jamieson
I work on behalf of HP
"Remember, I'm pulling for you, we're all in this together!" - Red Green.

Not able to install scanner part of 'HP PSC 1410 all-in-one'[SOLVED]

Despite trying instructions in the wiki, checking earlier reports of this problem on the forum and trying on reports from google, I am not able to install the scanner part of 'HP PSC 1410 all-in-one'. The command 'sane-find-scanner' finds it but 'scanimage -L' does not. Also xsane and simple-scan program do not find it. Any help will be appreciated.
(I also tried these entries in the udev sane rules:
ATTRS{idVendor}=="03f0", ATTRS{idProduct}=="4d11", MODE="0664", GROUP="scanner", ENV{libsane_matched}="yes"
"SUBSYSTEM=="usb_device", ATTRS{idVendor}=="03f0", ATTRS{idProduct}=="4d11", PROGRAM="/bin/sh -c 'K=%k; K=$${K#usbdev}; printf bus/usb/%%03i/%%03i $${K%%%%.*} $${K#*.}'", NAME="%c", MODE="0666", GROUP="scanner", ENV{libsane_matched}="yes"
but they do not work).
Some previous threads:
https://bbs.archlinux.org/viewtopic.php?id=107474
https://bbs.archlinux.org/viewtopic.php?id=65431
Not able to install sane-dev from AUR; 'makepkg -s' gives error:
==> WARNING: Cannot find the git binary required to determine latest git revision.
Last edited by rnarch (2012-03-28 05:05:09)

Git was not installed. So I installed it and ran 'makepkg -s' again. It ended with following error:
installing saned.conf in /etc/sane.d/saned.conf...
installing dll.conf in /etc/sane.d/dll.conf...
for dir in artec_eplus48u gt68xx snapscan epjitsu ; do \
/bin/sh ../mkinstalldirs /home/sane-dev/pkg/usr/share/sane/${dir} ; \
done
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/artec_eplus48u
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/gt68xx
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/snapscan
mkdir -p -- /home/sane-dev/pkg/usr/share/sane/epjitsu
/bin/sh ../mkinstalldirs -m 775 -g uucp /home/sane-dev/pkg/var/lock/sane
Usage: mkinstalldirs [-h] [--help] [--version] [-m MODE] DIR ...
Create each directory DIR (with mode MODE, if specified), including all
leading file name components.
Report bugs to <[email protected]>.
make[4]: *** [install-lockpath] Error 1
make[4]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[3]: *** [install-data-am] Error 2
make[3]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[2]: *** [install-am] Error 2
make[2]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make[1]: *** [install] Error 2
make[1]: Leaving directory `/home/sane-dev/src/sane-backends/backend'
make: *** [install-recursive] Error 1
==> ERROR: A failure occurred in build().
Aborting...
Please note the line: Report bugs to <[email protected]>. Is it a bug? Sane-dev was successfully installed by others, eg: https://bbs.archlinux.org/viewtopic.php?id=65431
Last edited by rnarch (2012-03-26 01:11:57)

HP PSC 1410 All in one Printer not installed

In windows 8 after complete and lastest installation of Driver of HP PSC 1410v All in one, in the Control Pannel, Device and Printer Tab only scanner icon is showing no any printer icon and no other HP Icon, so i can use scanner only of this model but not printer. After reading suggestions I install the windows 7 driver in windows 8 after solution of fatel error here is also only scanner is showing no facility for printing, please help me where I am wrong or whats solution fast plzzzzzz.

Hello Jai_pareek,
Welcome to the HP Support Forums! I see you would like to install your HP PSC 1410 to your computer running the Windows 8 Operating system. You tried downloading the Windows 7 driver but are now getting a fatal error. Please go ahead and start with the steps listed below:
1. Unplug the USB if using a direct connection.
2. Remove the HP PSC 1410 software from your computers Control Panel's Uninstall a program option.
3. Restart the computer.
4. Make sure ALL the PSC 1410 software is gone from the programs list as well as your HP folder listed under the All programs in your Start Menu.
5. Now go ahead and download the software and drivers for your PSC 1410 (DO NOT plug in USB until the software prompts you to):
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=al-110055-2&cc=us&dlc=en&lc=en...
6. Go ahead and print a test page.
7. If you are unable to print a test page, please run the HP Print and Scan Doctor- It was designed by HP to provide users with the troubleshooting and problem solving features needed to resolve many common problems experienced with HP print and scan products connected to Windows-based computers.
Please let me know if this was successful! I will watch for your reply.
Thank you,
HevnLgh
I work on behalf of HP
Please click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" to the left of the reply button to say “Thanks” for helping!

HP PSC 1210xi all-in-one

Hello, I've been trying to get the HP PSC 1210xi All-in-One running as I won't be able to use my current scanner soon.
However, it fails to run due to missing drivers. I'm running Windows 8.1 (64bit), which causes me some concern to the compatibility. I've tried several solutions - the HP installer tool does not support the PSC 1000 series, downloaded drivers seem to not work or are unable to run; "this cannot be run as without administrative privileges", even whilst I am logged onto the only account on this computer. The farthest I seem to have gotten was to run the driver .exe in compatibility mode for Windows XP (64bit), but this results in the above error, and also seemingly requires the installation disc, which I am currently missing.
Unfortunately, buying a new scanner is not an option for me right now, and I need a functioning one to work. I would be extremely grateful for any input you are able to provide, or even the possibility of being shipper a new disc.

Hi Ryog,
Unfortunately there is no CD or drivers to download from the site for Windows 8.1. The only drivers are the preinstalled Windows drivers and the Windows Update drivers.
I would do a hard reset to see if that will resolve the issue.
Leave the printer on and unplug the power cable from the printer and wall outlet for 60 seconds.
Then reconnect the power cable to the printer and wall outlet rather than a surge protector.
This ensures the printer is receiving full power and may help this situation.
Make sure the USB cable is connected directly to the computer. The USB cable shouldn't be longer then 6 feet.
If you are still having issues then try another USB port on the computer. Try another USB cable.
Is the USB port on the computer 2.0 or 3.0? I would recommend using the 2.0 port and cable. USB 3.0 are supposed to be backwards compatible.
Follow the steps in this document to get to the device manager to check to see if the printer is showing that it was detected by the USB cable.
How do I get into Windows Device Manager?
In the list click under Universal Serial Bus controllers, look for USB printing support or other devices, unknown device (make sure any other printers are turned off or disconnected) right click and update the driver.
If this is a Laptop then check the power management settings.
Access the device manager. Windows 8-How do I access the Device Manager.
Select universal serial bus controllers from the list, for each USB root hub, right click and left click on properties, for power management remove the check mark for "Allow the computer to turn off this device to save power". It allows computer to limit or turn off power for this device.
If this is a Desktop then try the USB ports on the back of the tower. The front ports are used mainly for keyboard or mouse.
If you need further assistance, just let me know.
Thank You.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Printing with Hp psc 1110 all-in-one

Hello, is the first time for me with macbook problem and I hope to find the solution because the question is drive me crazy ...
I've tried to install a printer HP psc 1110 all-in-one, but after te installation of driver and software when i start to print the printer return me every time the same error (that i find in the log of printer)
E [15/Jun/2010:16:39:39 +0200] Unable to execute /Library/Printers/hp/cups/Inkjet7.driver/Contents/MacOS/Inkjet7: no execute permissions (0100664)
E [15/Jun/2010:16:39:39 +0200] [Job 2] Unable to start filter "/Library/Printers/hp/cups/Inkjet7.driver/Contents/MacOS/Inkjet7" - Operation not permitted.
E [15/Jun/2010:16:39:39 +0200] [Job 2] Stopping job because the scheduler could not execute a filter.
I've tried to do the installation of software many times but the problem is still the same.
Can someone help me?
thank you so much

I think you might have installed Old HP SW that is not compatible with 10.6.x. You have 3 choices:
- Delete all the HP SW you installed. The in system prefs, re-add the printer. 10.6 will download the drivers you need.
- Delete all the HP SW you installed. Download the drivers manually from Apple. (http://support.apple.com/kb/dl907) Install them.
- Visit HP's web site and download 10.6 compatible drivers.
Note to everyone, over 2000 drivers are built into the OS. If they work, don;t install older SW on top of them. The list of built-in drivers is here: http://support.apple.com/kb/ht3669

HP psc 1610 All-in-one ERROR

Similar Messages

Maybe you are looking for