I need help for install and configure password sync from AD to OID

Hi guys!
I need to sync passwords from AD to OID, first all, ¿What software do I need? I read some docs and don't find the good config.
I'm trying with:
-Database 11g
-Weblogic 11g
-SOA 11g
-IDM 11g
-IAM 11g
First I install the Database and load the schemas with RCU, next install Weblogic without domian, next install SOA, next install IDM (OID and DIP) in a new Weblogic Domain, next install IAM, next configure IAM in the domain created before, next configure SSL, check the config by using ldapbind, next configure DIP.
It's that ok?
¿What I am doing wrong?
Thank you all.

If all you need is AD & OID then OIM is not required. DIP alone can handle this
Password sync should work using DIP. if this is not working then check synchronization mapping and verify that password attribute is also part of this AD-OID sync. Enable debug in synchronization profile or raise an Service Request with Oracle support.
Check
http://docs.oracle.com/cd/E23943_01/oid.1111/e10031/odip_actdir.htm#CHDIGDEH
and
http://docs.oracle.com/cd/E23943_01/oid.1111/e10031/odip_config_integration.htm#BABBFAAJ
and
http://docs.oracle.com/cd/E23943_01/oid.1111/e10031/odip_adpasswordsync.htm#CHDBIIJC
Atul Kumar

Similar Messages

What are the prerequsite for installing and Configure Knowledge management

Hi All,
what are the prerequsite for installing and Configure Knowledge management in CE 7.1 eph1.
Thanks
AB

Hi Michael,
Thanks for yor quick response.......Can you please tell me whats the alternative for KMC in CE 7.1 in portal
thanks
AB

Need help for Update and cancel SalesOrder

Hi All,
I written java code for create sales order based on salesquotation,now i want to update and cancel sales order ,i need help to update and cancel salesorder.
can give any related links for update and cancel salesorder.
Thanks and Regards,
Srinivas

Hi srinivas.L
It is simple, here is some sample code. You must use getbykey to get the document. Then once you got it you can make whatever changes you need. Then update it. where i have oOrder.Update() you can have oOrder.cancel
Dim oOrder As SAPbobsCOM.Documents
        oOrder = oCompany.GetBusinessObject(SAPbobsCOM.BoObjectTypes.oOrders)
        If oOrder.GetByKey(530) Then
            oOrder.Lines.SetCurrentLine(1)
            oOrder.Lines.WarehouseCode = "01"
            If oOrder.Update() <> 0 Then
                MsgBox(oCompany.GetLastErrorDescription)
            End If
        Else
            MsgBox("Nothing found")
        End If
Hope this helps

Need help setting up and configuring rsync

Hello
I need help setting up, or rather configuring rsync to sync data between my brand new iMac and my Macbook Air.
Here is what I would like to:
- I want all of the files on both machines to be an exact mirror or copy of each other. Basically I have an iMac for at home, and then a Macbook Air for the road.
- The main folder on both Macs is called 'Sara' and I want the contents (mainly the 'movies' folder, 'music' folder, 'documents' folder and 'pictures' folder) to immediately sync up with each other when both of them are on my home network.
- this means if I'm working on a file at home on my Macbook, it will immediately write to the same directory on my iMac and vice versa (if I'm working on file(s) on my iMac, it will immediately save the contents to my Macbook). This way, if I'm working on last minute project my iMac, and then have to head out the door to the airport, the file is immediately saved to my Macbook (no usb for USB transfer).
- hopefully this makes sense??
Any help is greatly appreciated!
Thanks

It's a lofty but unrealistic goal. Rsync does not run automatically. There is no realistic method of instantaneously synching two computers over the internet or even on a LAN.
I would suggest you might try using Synk Pro which, in theory, can keep two devices in sync when they are both on the same network (and both have shared and mounted drives.)
If you must do this with rsync then I suggest a Google search for rsync tutorials.

Need Help for Itunes and quicktime

Hi there,
I just formated my computer and my os is windows 2003 server. When I installed itunes, everything is fine however when I installed quicktime I got an error code : -3. What's going on? and after I done with the installation, I couldn't open an itunes as well I got an error message said : The exception Privileged instruction. (0xc0000096) occurred in the application at location 0x7ca2af84. I don't know what happened I did install itunes and quick time under windows 2003 before and it works fine, but now I got an error. I appreciate the answer, Thanks in advance.

by any chance, did you try downloading the QT Player
from the "QuickTime 7.1 with iTunes 6 for Windows
2000/XP" link on the QT download page? that one
actually leads to an itunes/QT installer bundle.
I did it this way
let's try a careful standalone QT 7.1 reinstall.
download and save a copy of the QT 7.1 standalone
installer to your hard drive. (we'll run the install
from there rather than online.) switch off
antivirus and antispyware applications prior to the
install.
Quicktime 7.1 Standalone Installer
if that install goes through okay, does your itunes
launch properly again?
I did like you said and I can not even uninstall quicktime from my computer. When I double click the installation package: It shows
Unhandled Exception
Error Number : 0x80040707
Description : DLL function call crashed : QTInstallCode.QuickTimeUninstallProc
Setup will now terminate
Also, itunes does not launch properly. I think there is something wrong because when I install the windows from the cd I can install and run these two programs(itunes and quicktime). They work fine and no problem at all. However, after I update windows by using windows update web site, I couldn't use these programs since then. I have no idea what is going on? Before I reinstall my os, I also use windows server 2003 with sp1 and I could run these two programs. I think may be the new version of itunes and quicktime that they put on the web site have some issues with the windows server 2003, not sure about that.
Thanks.
(if you get an error message on the QT standalone
reinstall, let us know what it says. include error
message numbers if you're getting any.)
love, b

I need help for cloud and ios5

Help me for cloud and ios5

Sounds like I have a similar problem. I just updated iPad, and iPhone to iOS5. I synced these devices with my iMac on iCloud. Calendars and contacts synced just fine. However for some strange reason I can no longer sync any music on my 32 GB iPhone. iTunes is telling me that I am beyond the phone's capacity with an "Other" item that is nearly as large as my music collection. Am I missing something here? Your help will be greatly appreciated.

Need Help for Installing TK ACTIONS PANEL for PHOTOSHOP CC

I recently just subscribed to Photoshop CC. And the first thing I try to do is to install the TK ACTIONS PANEL into photoshop. I did what I used to do with CS5 to install the TK ACTIONS PANEL. I follow the instruction the same way, but I couldn't get the panel install. Instead I got a message " Load panel xml error Error #2032 ". Please HELP!!!

Panel extensions were are developed using Adobe configurator and there were several versions and there needs to be a different install developed for each panel extension for each version of Photoshop there seems to be no compatibility between Photoshop versions each gets it own copy of everything. I developed a panel for one of my packages but don't use it or distribute it. Instead I just link Photoshop Scripts path to my scripts path and use a single copy of my scripts for all versions of Photoshop, I address Photoshop incompatible change in my scripts maintain a single script by adding code to test for Photoshop version in functions that need to be coded for various versions of Photoshop,

Need help for ACL and NAT for VoIP

Dear experts
I configure my PBX server to work with one VoIP provider. When I put the server in blank network, mean that without VLANs.
The IP PBX server can register to the VoIP provider system normally and I can make call out and receive calls normally.
However, when I put the PBX behind the Cisco router with some configuration. The PBX cannot register with the VoIP provider system.
Eventhough I can receive calls from outside but can not make a call from inside to outside, because of the PBX cannot register.
Could you please help me to point out what is wrong with my Cisco router configuration.
Thanks a lot
Building configuration...
Current configuration : 1982 bytes
! Last configuration change at 17:18:27 UTC Mon Feb 24 2014
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
enable secret 5 $1$ZJEF$8np0QvQTD1nTaOosa9yGW1
no aaa new-model
memory-size iomem 20
no ipv6 cef
ip source-route
ip cef
multilink bundle-name authenticated
crypto pki token default removal timeout 0
license udi pid CISCO2911/K9 sn FTX1603AH9C
interface Embedded-Service-Engine0/0
no ip address
interface GigabitEthernet0/0
description internal-LAN
ip address x.x.x.4 255.255.0.0
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/1.1
encapsulation dot1Q 11
ip address 172.x.x.1 255.255.240.0
interface GigabitEthernet0/2
description internet
ip address 50.x.x.93 255.255.x.x
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 100 interface GigabitEthernet0/2 overload
ip nat inside source static udp x.x.x.8 5060 50.x.x.93 5060 extendable
ip route profile
ip route 0.0.0.0 0.0.0.0 50.x.x.94
ip route 172.16.240.0 255.255.x.0 x.x.x.5
ip route 172.16.242.0 255.255.x.0 x.x.x.5
access-list 100 permit ip x.x.0.0 0.0.255.255 any
access-list 100 permit ip 172.16.240.0 0.0.0.255 any
access-list 100 permit ip 172.16.242.0 0.0.0.255 any
access-list 100 permit udp any any range 5004 5090
access-list 100 permit udp any any range 10000 20000
control-plane
line con 0

You really don't want to use NAT with SIP. Odds are it won't work. This is because SIP embeds hostnames/IP Addresses inside the packets, and standard NAT does not look inside packets.
If you want a NAT-type functionality for SIP, you need something called a session border controller. Look up Cisco CUBE
http://www.cisco.com/c/en/us/products/unified-communications/unified-border-element/index.html
https://supportforums.cisco.com/docs/DOC-17964
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-border-element/99863-cube-config.html
GTG
Please rate all helpful posts.

Need help for installing OS after installing new hard drive

I have an imac 27 2010.
The hard drive has failed for the 2nd time. I have installed a new hard drive again. When trying to install the OS, it looks to begin but then tells me it can not be completed.
I had gone the the erase, then partition steps previously.
Any advice?
I do have a time machine copy to restore from if I can get that far as well as the discs handy to use.
Any help would be greatly appreciated.

Which OS version install disk do you have? It's not Mavericks since that does not come with a disk.
And you are trying to install Mavericks? If so, are you using the Internet Recovery Option (press Command + Option + R while restarting/rebooting)? I recently read of a case where the user was unable to reinstall the old OS (in that case Snow leopard) and he could not install Mavericks either. He took it to an Apple store and they bypassed the ID/password requirements and reinstalled it for him.

I need Help for Installing the JamVM on TS-7800 SCB

Hello,
can anyone give me some StarterHelp to install the JamVM (or any other VM) on the follwing SBC (Arm)?
http://www.embeddedarm.com/products/board-detail.php?product=TS-7800&tab=options
Didn't need I a crosscompiler for the target-arch? In the INSTALL-File of the jamvm-package i didn't reed somthing about using a crosscompiler.
For you help i'm very thanksfull.
Best regards.

can u guys solve the problems??? i also working on the ARM board which came from China. my problem also almost the same.still configure how to run the java program on that board. i just read from this journal, http://www.linuxjournal.com/article/8757. this author said that we don't have to install JVM in our target. we just have to use GCJ (GNU Compiler for Java), which is will compiles our Java source down to the machine code for the target. but, the author used PowerPC target, that was the issue. i already try this method but it was not working yet. i also don't know why yet.please let me know if u guys can slove your problems. tq~

Need help for ACL and NAT

Hi all
I setup a router 2911 with the configuration below for the phone system inside handle all calls in and out from and to the outside provider VoIP.
I can receive the calls from outside all time but I cannot make the call from the inside to outside.
I think that I miss some configuration in router.
The 172.a.b.c is the IP phone system.
Please give me any advice
Thanks a lot.
The router configuration:
interface Embedded-Service-Engine0/0
no ip address
interface GigabitEthernet0/0
description internal-LAN
ip address 172.x.x.4 255.255.x.x
ip accounting output-packets
ip nat inside
ip virtual-reassembly in
duplex auto
speed auto
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
interface GigabitEthernet0/1.1
encapsulation dot1Q 11
ip address 172.16.208.1 255.255.240.0
interface GigabitEthernet0/2
description internet
ip address 50.x.x.93 255.255.x.240
ip accounting output-packets
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 100 interface GigabitEthernet0/2 overload
ip nat inside source static udp 172.a.b.c 5060 50.x.x.93 5060 extendable
ip route profile
ip route 0.0.0.0 0.0.0.0 50.240.226.94
ip route 172.16.240.0 255.255.254.0 172.10.0.5
ip route 172.16.242.0 255.255.254.0 172.10.0.5
ip access-list extended VLAN-voice
access-list 100 permit ip 172.x.0.0 0.0.255.255 any
access-list 100 permit ip 172.16.240.0 0.0.0.255 any
access-list 100 permit ip 172.16.242.0 0.0.0.255 any
control-plane
line con 0
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
login
transport input all
scheduler allocate 20000 1000
end

You really don't want to use NAT with SIP. Odds are it won't work. This is because SIP embeds hostnames/IP Addresses inside the packets, and standard NAT does not look inside packets.
If you want a NAT-type functionality for SIP, you need something called a session border controller. Look up Cisco CUBE
http://www.cisco.com/c/en/us/products/unified-communications/unified-border-element/index.html
https://supportforums.cisco.com/docs/DOC-17964
http://www.cisco.com/c/en/us/support/docs/voice-unified-communications/unified-border-element/99863-cube-config.html
GTG
Please rate all helpful posts.

Need help for email and BBM

Hi i'm Alex and im having problems setting up my email and bbm on my blackberry curve 8520. i'm with orange as a dolphin plan and just wondering if any one can help set up my bbm and enterprise Activation Password.

Hello !
It seems you dont have BlackBerry Internet Service (BIS) Plan activated on your device.
Please contact your Service Provider for activating it.
Hope this resolves your Problem!
If your problem has been resolved then would request you to Click on "Like" and accept as "Solution" so that other Advisors doesnt invest their time on this Message anymore.
Thanks.

Need help for installing weblogic6.1 as windows service

HI,
I am installing weblogic6.1 as windows service.I have made all required changes in "installService.cmd"(see below) and everything is working fine except that i am not able to set a log for putting all stdout mesaages to a text file.
Please can anybody tell me if i am missing anything or any step.
Thanking you in advance.
@echo off
SETLOCAL
cd E:\bea\wlserver6.1\config\mydomain
set WLS_PW=weblogic
rem *** Set Classpath to load Weblogic Classes
set CLASSPATH=.;.\lib\weblogic_sp.jar;.\lib\weblogic.jar;.\lib\log4j-1.2.8.jar;.\lib\soap.jar;E:\bea\wlserver6.1\config\mydomain\applications\DefaultWebApp\WEB-INF\classes;
set CLASSPATH=%PFIZERDAT_CP%;%CLASSPATH%
rem set CLASSPATH=.;E:\bea\wlserver6.1\lib\weblogic_sp.jar;E:\bea\wlserver6.1\lib\weblogic.jar
rem *** Set Command Line for service to execute
rem *** %JAVA_HOME%\java will automatically be prepended.
set CMDLINE="-ms64m -mx64m -classpath \"%CLASSPATH%\" -Dweblogic.Domain=mydomain -Dweblogic.Name=myserver -Djava.security.policy==\"E:\bea\wlserver6.1/lib/weblogic.policy\" -Dbea.home=\"E:\bea\" -Dweblogic.management.password=weblogic weblogic.Server"
@REM "%JAVA_HOME%\bin\java" -hotspot -ms64m -mx64m -classpath "%CLASSPATH%" -Dweblogic.Domain=mydomain -Dweblogic.Name=myserver "-Dbea.home=E:\bea" -Dweblogic.management.password=%WLS_PW% -Dweblogic.ProductionModeEnabled=%STARTMODE% "-Djava.security.policy==E:\bea\wlserver6.1/lib/weblogic.policy" weblogic.Server
rem *** Install the service
"E:\bea\wlserver6.1\bin\beasvc" -install -svcname:"DAT-Service" -javahome:"E:\bea\jdk131" -execdir:"E:\bea\wlserver6.1" -extrapath:"E:\bea\wlserver6.1\bin" -cmdline:%CMDLINE% -password:"weblogic" -log:E:\bea\wlserver6.1\config\mydomain\myserver-stdout.txt
ENDLOCAL

Hi Animesh....
I am having the same problem.
can you please tell me if you ever found out a solution to this problem?
Thank you
Krishna Tummeti

Need help for coding and designing

Hi All,
Problem Statement
A financial institution is in the verge of automating their existing “customer data management” system. Currently they are maintaining their
customer data in a comma separated file (CSV) format. You, as a software consultant have been requested to create a system that is flexible,
extensible and maintainable. Your proposed system should also take care of moving the data from the old system to the new one.
Customer has following specific requirements
1.This is an internal offline application and need not be a web based solution
2.The new application should be cost effective
3.The application should have good response time as compared to the ones suggested by other vendors
4.Phase 1 work should concentrate mainly on building a simple system which moves the data from CSV to the new one and display the
moved data on the screen.
Sample CSV file containing customer data
<first name>, <age>, <pan number>, <date of registration>
Ramesh, 28, JWSLP1987, 30/01/2006
Rajesh, 32, POCVT2087, 23/10/2005
Shankar, 39, TRYUP3945, 24/7/2003
Shyam, 45 BLIWP5612, 15/3/2004
Requirements for coding DOJO
•Ensure that your solution is built around open source frameworks and tools to avoid licensing issues. (Ex: Eclipse, MySQL, etc)
•Please give me any idea to write code for this issue.
Thank you.
Edited by: user636482 on Oct 28, 2008 2:03 AM

The first requirement is to NOT use software like "Oracle".
The specifications are to use a CSV file as the "data source". The case asks you to "move" the data from CSV to "the new one" and display the moved data.
So this sounds more like a data load routine -- but not to load into Oracle.
You are in the wrong forum.

Help! : Install and configuration of OID and LDAP

Hi,
I'm trying to install OID and run a LDAP server.
I installed OID in my 9iR2 database, it seems ok.
When I try to connect in ODM, it says 'LDAP server not running'... I don't find in Control panel/services any service naming like 'LDAP' (I just find "ODS_sid" who is runnig), is there something I forgot to install ??
In the same way I haven't any tables in ODS/ODS@my_sid, is it normal ??
Thanks in advance,
Sandrine

Hi Diego,
The maximum number of concurrent users logged on allowed by the current license keys has been reached.
Attempt to log on later after other users have logged off, or upgrade the license keys.
Or you can get in touch with your Accounts Manager to check the license keys, whether they have been expired, or need to be upgraded.
-Shreyash

I need help for install and configure password sync from AD to OID

Similar Messages

Maybe you are looking for