1 of 2 Airport Expresses Not Responsive After New Wireless Router Installed

Installed a new Belkin N+ wireless router and now one of my Airport Expresses that I use for Airtunes cannot be "seen" by my computer. Tried resetting with no luck. One of them is a g and the other an n. It is the n that I'm having the issue with.

Welcome to the discussion area!
Temporarily, connect an ethernet cable directly from your Mac to the AirPort Express. This will usually allow AirPort Utility to "see" the Express so that you can reconfigure it to work with the new router. You can disconnect the ethernet cable after you have updated the settings on the AirPort Express.
If this is not successful after a few tries, then the next step would be to reset the Express back to a factory default condition and reconfigure it again. To do this you would:
Power down the Express for a few moments
Hold in the reset button and keep holding it in as you plug the Express back in to power
Release the reset button after 8-10 seconds

Similar Messages

Can't get airport express to work with new wireless router

I just swapped out a linksys wrt54gl for a linksys E1200 wireless router on my home network. My PCs and iPads, and TV all made the switch to the new network fine, but the airport express isn't working. All I want to use it for is to transfer iPad audio to my home speakers. but my iPad AirPlay shows the old Airport as an option, I can switch to the Airport, no sound comes out the home speakers, then the iPad reverts AirPlay back to iPad. This model Airport just has power, USB, and LANA ports, so it doesn't seem like it would be complicated. A CAT 5 cable goes from the airport WAN port to one of the ports on the back of the new wireless router. What did I overlook?

I thought I'd jump in here with you network experts for some help with a related networking problem.
Equipment: iMac 24-inch, Early 2009 2.93 GHz Intel Core 2 Duo; 2 MBP w/Retina Display; AirPort Express version 7.6.4 (Conncected Using: DHCP; Router Mode: DHCP and NAT); Comcast/Xfinity Gateway 1 Modem w/2.4 GHz WiFi.
#1. Comcast forced me to change modems to their Gateway 1 saying mine was at “End of Life.” Previously, my home network was set up with AP Express and worked fine using my iMac as a server. After installing the Gateway 1, I could not get my network to work after repeated calls to their support, online chats, trial and error, reading community chats and articles, etc. I put the Comcast modem in passive mode using the “Bridge” setting and re-established my network with my AP. I’m using my iMac as a server for file sharing with my two MBP’s. The network isn’t recognized in sleep mode and will not wake from sleep and I can’t find it or Connect to Server when the computer is asleep. I’ve tried all combinations within the Energy Saver/Screen Saver/Security preferences. I’ve reset the SMC and other like resetting to factory defaults. How can I fix this and what are the correct settings for my home network to function again with my AP Express?
#2. TimeMachine stops doing backups when the computer is in sleep mode, understandably because I’m not making any changes on the iMac that need to be backed up. But using my laptops on the network, I am making changes in shared files that are hosted on the iMac that I would like backed up. I cannot get the schedule feature to work to wake up the computer long enough to do a backup nightly because, as a security feature, I log out after 30 minutes of inactivity. I understand the schedule doesn’t work unless you’re logged in. Is there a way for me to make this work?
Thanks!

Airport express not found after setup

I have a maddening situation. At the beginning of setting up my airport extreme, the computer has no problem finding the wireless device. However, after the A/E is configured and added to my current network (linksys router), the computer can't find the A/E anymore.
What's going on?

The following are Apple's instructions for setup using the Airport Setup Assistant, which is different from Airport Utility, but most of the steps are the same. Some are important for your installation, such as "do NOT select extend the range of my Airport..." and entering your network password correctly. Some steps, like plugging in the Airport, you probably already figured out
Since your router is a Linksys product, after the Express is set up you will no longer be able to see it using Airport Utility. The reason is that you set up the Express using its wireless network (Apple Network xxxxxx), which is subsequently disabled after setup. Once you're done and you click Update you'll be using your Linksys wireless network. Airport Utility only recognizes Airport networks. You didn't create one with your Express nor do you want to given your desired setup. If you need to use Airport Utility to configure the Express again you'll need to perform a hard reset.
If everything's right and you have checked iTunes Preferences > Devices "look for remote speakers connected with Airtunes" option you should see a new menu appear in the lower right of the iTunes window.
If this doesn't work, try disabling your router's encryption temporarily to simplify things. Reset the Express and run Airport Utility without a password this time. You may also need to modify your Sharing > Firewall settings too.
Hope it helps!
Plug AirPort Express into a power outlet.
On your computer, join the wireless network created by AirPort Express.
Open AirPort Setup Assistant. Mac users: Find it in /Applications/Utilities/. Windows users: On the Start menu, point to All Programs and click AirPort.
When you see the Introduction screen, click Continue.
Select "Set up a new AirPort Base Station" and click Next.
When the AirPort Setup Assistant confirms that it has found your AirPort Express, click Continue. (If >your AirPort Express wasn't found, click Try Again.)
Select "Connect to my current wireless network."
Be sure that "Extend the range of my AirPort wireless network" is not selected (this option is used >only for WDS).
Click Next; AirPort Express Assistant will scan for your existing wireless network. Once it finds it, click Next again.
Choose the correct network (there may only be one) from the Wireless Network Name menu. If the wireless network is password protected, you will be prompted to enter the password. Enter the password and then click Next to continue.
Note: If you have difficulty with your password, you can get help with joining a third-party WEP-protected network.
Enter the name of your AirPort Express.
Tip: If you don't know the name, it's what appears in iTunes as the name of your AirTunes remote speakers.
Click Next.
Assign an administrator password for AirPort Express. This password can be different from any network password, and is used for just changing settings on AirPort Express.
The Summary screen outlines the configuration options you've set. Optionally, you can click Show Passwords to review the administrator and network passwords. Finally, click Next to update AirPort Express with your settings.

Airport Express not working after power blip

Hello,
I have been here before and gotten a lot of great advice from participants here, but I forgot my user name so I'm starting fresh. Anyway, I have a feeling I'm in for some bad news but I thought I would post just in case...
I have an Airport Express plugged directly into the wall behind my iMac in my house, and it has worked great for about 20 months. The computer where I installed and maintained the Airport Express is an iMac running OSX 10.7.5, if that matters.
Two nights ago our power went out for approximately 5 seconds.
I immediately discovered our WiFi was out. I checked the AirPort Express and it was flashing very fast yellow.
I first restarted the cable modem and verified that it was still working. The ethernet cord worked. I got out the manual and tried following all the instructions for resetting the Airport. The Airport device never showed up in the airport utility. At one point after using the reset button on the Airport, the light mysteriously changed to solid green and I thought I had a chance, but the device still didn't show up in the utility and after I unplugged the device again it just started the fast yellow light flashing again.
I have gone through other recent threads on this topic and I keep thinking I'm missing something. In the whole life of this device it's only gone down once before and it was a long confusing frustrating struggle to get it to work again, but I did. At that time the device was doing the same thing (flashing yellow) and wasn't showing up in the Airport Utility but somehow I got it working again. So I'm hoping maybe, just maybe, there's a procedure I haven't tried.
I understand people say you should protect your equipment with surge protectors and we actually do have everything else plugged into one. But the manual of the Airport Express makes such a big deal about obstructions and cords and other electronic equipment and shows a picture of the device plugged directly into the wall, so that's what I did. If it got fried in that power blip and I have to buy a new one, should I just plug it into the surge protector anyway?
If it's dead for good, I'm annoyed that I got less than 2 years of use out of it. I read in a thread here that they die on a lot of people because they run really hot and 2 years is average life. Seriously?
If I take it to the "genius" bar, will they be able to determine if it's dead or not before I buy a new one? Should I buy something else more reliable...ie, non-Apple possibly? If I had known this device had reliability problems, I would have shopped around more, but I always buy Apple.
Thank you for reading this and any reccommendations would be appreciated.
sincerely,
susan

A rapidly flashing LED is unusual, and strongly indicates a problem that can't be fixed.
I read in a thread here that they die on a lot of people because they run really hot and 2 years is average life. Seriously?
I doubt it; I have never had any of them fail and the oldest is about six years old. I don't pay any particular attention to cooling requirements. There were a rash of power-supply related failures due to defective components a long time ago, but it has been many years now. It affected many manufacturers of electronic equipment, not just Apple.
will they be able to determine if it's dead or not before I buy a new one?
Yes, absolutely. They will "hard reset" it, which you can do yourself before you go. See below. That is the extent of Apple's AirPort Express troubleshooting ability.
The damage it sustained may not have been related to power anomalies at all. In fact, if the power supply was damaged you probably wouldn't get any LED activity at all. I suspect the damage may have involved to your cable company's equipment. Improper lightning protection or surge suppression is very common, and can affect everything connected to your cable company's equipment. You should consider contacting them to determine if their equipment is properly installed. They're going to say their liability is limited to their equipment, and anything beyond their cable modem is your problem, so make sure they did their work properly.
To "hard reset" an AirPort Base Station: make sure it's powered up, then press and hold its tiny reset button and keep it depressed for five to ten seconds, long enough for its LED to flash amber rapidly. Release the reset button. Then, the LED will glow amber steadily for about a minute. Then, it will flash amber, slowly, about once every second or two, waiting for you to configure it with AirPort Utility.

Airport express not working after updating to 7.6.3

Hi all,
I bought my airport express about 6 months ago. It's been working perfectly. Then this morning, I woke up to the blinking amber lights, not good.
I restarted the modem, and checked the connection (by hooking up my mbp directly to the modem) and everything is fine. I plugged in the ethernet cable to airport express, powered down then up, no luck. Airport utility popped up (on my mbp) asking me to update firmware to 7.6.3 (I had 7.6.2). So I reconnected my mbp to the modem and updated the firmware, connected the ethernet cable back to airport express, powered down/up, still no luck. I grew desperate and did a hard reset, still nothing!
I am not sure what happened here, or if anything had changed, since it was working fine as I went to bed last night.
anyone else seen this before? i checked with Apple, it seems that my airport express is out of the free-repair period.
pls help
thanks a lot

Worked on it some more and finally realized that I've plug the ethernet cable in the LAN port instead of WAN port. So, internet is back. Still don't know what happened (when it died), but owell.

Airport Express not working after update

I can no longer connect to my network through my Airport Express.
This afternoon I started up the software updated program in my MacBook Air and through my fully functioning network a whole bunch of updates were downloaded and installed.
But when everything was done I could no longer connect to my network through my Airport Express!
Unfortunately I didn't really notice what kind of updates I was installing.
There were seven in total. I think one was a firmware for my MacBook Air.
I also think there was one for my Airport Express because the last update was about it somehow and it needed to close down the network in order to finish the update. But when it was supposed to reconnect nothing worked.
I've turned off my modem, my airport express and my air but there's been no improvement.
My Win PC can't access the network any more either.
I've also tried to put the network cable straight in my PC and it works fine, so there's nothing wrong with the modem or the cable.
It must be my Airport Express...
The Airport Utility program can't find my Airport Express.
I can find other networks in the area but not my own.
What to do?
Any help is greatly appreciated.
Tommy

I got some help so that I could see what was updated:
2008-07-06 15:16:26 +0200: Installed "Keynote Update" (4.0.2)
2008-07-06 15:16:43 +0200: Installed "Pages Update" (3.0.2)
2008-07-06 15:16:47 +0200: Installed "MacBook Air EFI Firmware-uppdatering" (1.0)
2008-07-06 15:16:57 +0200: Installed "AirPort-verktyg" (5.3.2)
2008-07-06 15:24:31 +0200: Installed "Mac OS X Kombinerad uppdatering" (10.5.4)
2008-07-06 15:25:04 +0200: Installed "Numbers Update" (1.0.2)
2008-07-06 15:25:54 +0200: Installed "QuickTime" (7.5)
2008-07-06 16:37:59 +0200: Installed "Keynote Update" (4.0.3)
2008-07-06 16:38:20 +0200: Installed "iDVD-uppdatering" (7.0.2)
2008-07-06 16:38:26 +0200: Installed "iMovie-uppdatering" (7.1.2)

Airport Express not working after update 10.6.8????

Connect macpro to hub/wireless router via ethernet, my airport express base station connected wirelessly and plugged into stereo jack.
Worked fine managed the base station through macpro always automatically saw it.
Updated to 10.6.8 and computer cannot see it, only sees it if i turn on the airport on macpro but i dont want to do this (even then is not working correctly itunes doesn't see it only Airport utility).
Wt is going on?? Cant think why this has changed?
Any way of returning back to the previous state easily? This update *****!

MrComputer wrote:
Connect macpro to hub/wireless router via ethernet, my airport express base station connected wirelessly and plugged into stereo jack.
Worked fine managed the base station through macpro always automatically saw it.
Updated to 10.6.8 and computer cannot see it, only sees it if i turn on the airport on macpro but i dont want to do this (even then is not working correctly itunes doesn't see it only Airport utility).
Wt is going on?? Cant think why this has changed?
Any way of returning back to the previous state easily? This update *****!
This is where you restore the backup you made prior to the update.

AirPort Express Not Able to Connect Wirelessly

Hardware is iMac 2.4 GHz Intel Core 2 Duo with 4 GB 667 MHz DDR2 SDRAM. Mac OS 10.6.8
Connected to Internet via Motorola Surfboard SBG6580 Modem / Router, so I connect by wireless through the modem.
I followed the installation instructions to install AirPort Express to play music on my home stereo. I connected the Airport Express to the receiver by the tape port. I was not able to install AirpPort Express via wireless mode, so I connected the iMac to the AirPort Express by CAT-5 hard wire cord. The installation was successful and the AirpPort Express obtained an AP address. I was then able to play music from iTunes pm the iMac through the stereo speakers...as long as the AirPort Express was connected by hard wire to the iMac.
When I remove the CAT-5 cord from the AirPort Express, the AirPort Express retains the green light, but it is not able to receive data from the iMac. To the contrary, the AirPort Utility is not able to find any AirPort wireless devices unless the AirPort Express is connected via the hard wire CAT-5 cord.
As an experiment, I then connected the AirPort Express to the cable modem / router via the hard wire CAT-5 cord. The AirPort utility on the iMac was still not able to find any AirPort wireless devices. Further, the model then assigned a different AP address to the iMac so that it was not able to connect to the Internet..
Meanwhile, the AirPort Express still retains the green light, indicating the installation was a success and that it is ready to transmit.
Any advice to resolve this issue would be very much appreciated. Thanks in advance for your thoughts.

I suggest that you start by performing a "factory default" reset on the 802.11n AirPort Express Base Station (AXn) to get it back to its "out-of-the-box" configuration. By default, the AXn will broadcast an unsecured wireless network with a Network Name of something like: Apple Network NNNNNN
After the reset has completed, plug the AXn into power, and then, verify from the iMac that this network shows up in the list of networks under the AirPort icon in the OS X menu bar. Does it?
If so, then from the AirPort icon, switch your iMac to connect to the AXn's wireless network. Note: You will temporarily lose the Internet connection from your Motorola router. Then, run the AirPort Utility. The Utility should now find the AXn. If not, use the Utility's "Configure Other" option under the File menu option in the Utility's menu bar. Enter 10.0.1.1 for the Address and "public" for the Password.
AirPort Utility > Select the AXn > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <existing Motorola's wireless network>
Wireless Security: <select the encryption type of the existing wireless network>
Wireless Password: <enter the existing wireless network password>
Verify Password: <re-enter the existing wireless network password>
AirPort Utility > Select the AXn > Manual Setup >Music
Enable AirPlay (checked)
iTunes Speaker Name: <enter desired speaker name>
iTunes Speaker Password: (optional)
Verify Password: (optional)
Click Update to write the new settings to the AX

AirMac Extreme and Airport Express not working with Netgear N Router?

I've been using an AirMac Extreme (old model) as a wireless router, and Airport Express for it's airtunes functionality (conected to my Hi-Fi).
These used to work fine, and both would show up in my Airport Utility on my Macs.
I've now just upgraded to a 50MG broadband contract, and the engineer gave me a Network router as my old AirMac Extreme couldn't handle that bandwidth.
When I connected my AirMac Extreme to my Netgear router I then got conflicts, sometimes it wouldn't show up, and it really slowed down my wireless signal. As a result the contractor for my broadband recommended I disconnect my Air Mac Extreme from the router. Speeds went up for the internet, but now I can't get my airtunes to work.
What I want to know is can I just use my Netgear to transmit the broadband signal so I get maximum internet speeds, but then have my AirMac Extreme and Airport Express connected so that I can still listen to my itunes wirelessly?
Ideally I'd like this to all be set up so that I could be conected to the internet through the Netgear wirelessly and listen to my itunes through the Airport Express at the same time.
Thanks in advance for any advice.

I am sorry that I don't have a definitive answer but I also have Windows computers and I have "inherited" some older Apple devices from my son and am trying to learn about them so in addition to searching this group, I "Googled" "1st generation airport express" and it listed many specific posts in this group - I read them all and they might answer your question - good luck

Airport express using WPS to Linksys Wireless router?

I have a Linksys Wireless router set up to server wireless signal to macs and PCs in my office. It works great, but one of the far offices can't get enough signal.
I bought an airport express assuming I could use it as a repeater in this office.
I'm having some trouble connecting it (config goes great, then when i try and enable WPS mode - entering the current Linksys ID it just flashes orange after restart).
Any tips? Should this be possible?
.dave

Never found a solution to this.

Airport Express with D-link 624+ wireless router.

Have got a D-link wireless router connected. Wireless internet works fine on its own, but I cannot connect the apple airport express to the wireless internet, so I have to keep switching connections and am unable to use the internet at the same time as streming music to my stereo....what am I doing wrong?
please help me. I thought I knew computer gear, but was SOOOO wrong.

I had a DL 624+ (and have since abandoned it). I had a lot of instability problems with it, which seemed to be related to the Dlink DHCP implementation. I was watching the log on the router, and I was seeing the dlink constantly re-issuing DHCP addresses to the macs on the network - it would renew the addresses twice a minute.
I had seen some posts which suggested that there were problems with either long DHPC client names, or client names which had non-alphanumeric characters in them. (Note if your machine name has spaces, this could happen.)
So, you might want to try:
-Assigning static IP addresses and see if the problem goes away
-checking your DHCP client names to make sure they are between 8-12 characters
Hope this helps!

WDS setup with Airport Express and other(non-Apple) wireless router

Hi,
I am trying to configure a wireless network with one airport express and one Planex Wireless access point. Can anyone please point me to the settings to be made for such a scenario? I can use either of them as the main WDS device, and have a (wired)router provided by the ISP in the network.(so total 3 devices : airport, planex a/p , ISP router)
Thanks.

I'm having the same problem, both with a Linksys WRVS4400Nv2, and a WRT54G. I've not put much effort into the WRT, but the WRVS was such a pain that I don't think I can get it to work at all.
The WRT doesn't have a section on WDS, but I've read that it's supported anyways, and nothing needs to be enabled on it. Is there a good step-by-step available here or elsewhere that uses close to the same router and Airport Express units, on the latest Airport setup software?
Basically, I'm trying to set this up for a guy in an ~8000 sq. foot house so he has wireless throughout it, and he wants itunes streaming from the AX. Has anyone done this?
Message was edited by: manderso

EPrint does not work after new wifi router on Verizon DSL

I have been using ePrint on my iPod, iPad, and iPhone for a few months without a problem, but recently had to switch to a new wifi router on my Verizon DSL, as my wifi kept turning off and Verizon's solution was an updated wifi router. Since the switch, I cannot ePrint from my mobile devices. I can, after reconfiguration, print from my laptops. The ePrint app still finds the Deskjet 3050a, says "sending to printer", but will not print. The ePrint is turned on. I tried to delete the app and reinstall in hopes that I can start fresh, but it still does not work. I tried to add a new printer, with the email supplied on the ePrint screen on the printer, but nothing.
Any ideas?

Hi Honor Student
Is your printer connected to the new router as it sounds like it is still looking for the old one ? Maybe just disconnect it and reconnect it again to your new router and then the ePrint APP should pick it up.
I work for HP.
Thanks
Caroline
Although I am a HP employee, I am speaking for myself and not for HP.

Is it possible to create a hot spot with Apple Airport Express 2nd Generation Dual Band Wireless Router, usefull in a hotel with ethernet wall sucket.

is it possible to create a hot spot with apple Airport express 2 generation and use it i a hotel with ethernet wall socket and use it with my Ipad 2?

HenrikAppleJespersen wrote:
is it possible to create a hot spot with apple Airport express 2 generation and use it i a hotel with ethernet wall socket and use it with my Ipad 2?
Yes, it is one of the things AirPort Express was specifically designed for.

System restore on DV6 not working after new hard drive installed (Vista 32-bit)

Hi there,
I have a HP Pavilion Entertainment laptop (DV6 1210sa) and recently on start up I have been receiving a message saying that the hard drive is at imminent risk of failure. I therefore burned the restore CDs and bought a new hard drive: (A Toshiba 2.5 inch 80gb SATA hard drive 5400 RPM). The first part of the restore completes successfully then the HP screen appears after a restart and then goes to install windows, but before this begins I receive a message saying “Windows setup could not configure windows to run on this computer.” I then have to restart and get the same message. Is this drive somehow incompatible? Is there something I’m missing?
Thanks in advance

Here are the factory specs for your HP Pavilion dv6-1210sa Entertainment Notebook Computer. Based on the specs, the original hard drive was 250GB. This could be a factor in your issue. It could also be that the drive is an advanced format (AF) drive. Please provide the model of the drive for our review.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

1 of 2 Airport Expresses Not Responsive After New Wireless Router Installed

Similar Messages

Maybe you are looking for