1602i AP cannot connect to CT2504 Controller
Hi all,
I have a CT2504 with
Software Version
7.5.102.0
Field Recovery Image Version
System Name
Cisco_a5:d
I also have a 1602i AP with the software 15.2.4-JA1
The AP is trying to connect to the controller, but fails. I get the following log:
*Sep 25 16:58:33.035: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Sep 25 16:58:33.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_i
p: 192.168.0.250 peer_port: 5246
*Sep 25 16:58:33.483: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully
peer_ip: 192.168.0.250 peer_port: 5246
*Sep 25 16:58:33.483: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.0.250
*Sep 25 16:58:33.483: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination
*Sep 25 16:58:33.483: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process m
essage type 10 state 5.
*Sep 25 16:58:33.483: %CAPWAP-3-ERRORLOG: Failed to handle capwap control messag
e from controller
*Sep 25 16:58:33.483: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap pac
ket from 192.168.0.250
*Sep 25 16:58:51.611: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceed
., 1)x(UNKNOWN_MESSAGE_TYPE (5)
*Sep 25 16:58:51.611: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Sep 25 16:58:51.611: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192
.168.0.250:5246
*Sep 25 16:58:51.655: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led sta
te 255
*Sep 25 16:58:51.675: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to a
dministratively down
*Sep 25 16:58:51.675: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to a
dministratively down
*Sep 25 16:58:51.687: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 25 16:58:51.727: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 25 16:58:52.675: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Sep 25 16:58:52.723: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to do
wn
*Sep 25 16:58:52.731: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to r
eset
*Sep 25 16:58:53.715: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
*Sep 25 16:58:53.723: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to down
*Sep 25 16:58:53.767: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Sep 25 16:58:53.775: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to do
wn
*Sep 25 16:58:53.783: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to r
eset
*Sep 25 16:58:54.767: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
1, changed state to up
*Sep 25 16:58:54.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to down
*Sep 25 16:58:54.811: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Sep 25 16:58:55.811: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio
0, changed state to up
This repeats without success. Any help would be appreciated.
I only have the second port connected to the switch. It is also the management port. I don't have a lot of info about the interfaces, so do not know if this is the best option. Run-config is as follows:
System Inventory
NAME: "Chassis" , DESCR: "Cisco 2500 Series Wireless LAN Controller"
PID: AIR-CT2504-K9, VID: V01, SN: PSZ172304B8
Burned-in MAC Address............................ 10:F3:11:A5:DD:20
Maximum number of APs supported.................. 5
Press Enter to continue or to abort
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 7.5.102.0
Bootloader Version............................... 1.0.18
Field Recovery Image Version..................... 7.4.1.30
Firmware Version................................. PIC 16.0
Build Type....................................... DATA + WPS
System Name...................................... Cisco_a5:dd:24
System Location..................................
System Contact...................................
System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
IP Address....................................... 192.168.0.250
Last Reset....................................... Power on reset
System Up Time................................... 0 days 0 hrs 42 mins 36 secs
System Timezone Location......................... (GMT +2:00) Jerusalem
System Stats Realtime Interval................... 5
System Stats Normal Interval..................... 180
Configured Country............................... TR - Turkey
Operating Environment............................ Commercial (0 to 40 C)
Internal Temp Alarm Limits....................... 0 to 65 C
Internal Temperature............................. +31 C
External Temperature............................. +36 C
Fan Status....................................... 4200 rpm
State of 802.11b Network......................... Enabled
State of 802.11a Network......................... Enabled
Number of WLANs.................................. 1
Number of Active Clients......................... 0
Burned-in MAC Address............................ 10:F3:11:A5:DD:20
Maximum number of APs supported.................. 5
Redundancy Information
Redundancy Mode ................................. SSO DISABLED
Local State...................................... ACTIVE
Peer State....................................... N/A
Unit............................................. Primary
Unit ID.......................................... 10:F3:11:A5:DD:20
Redunadancy State................................ N/A
Mobility MAC..................................... 10:F3:11:A5:DD:20
Redundancy Management IP Address................. 0.0.0.0
Peer Redundancy Management IP Address............ 0.0.0.0
Redundancy Port IP Address....................... 0.0.0.0
Peer Redundancy Port IP Address.................. 169.254.0.0
AP Bundle Information
Primary AP Image Size
ap1g1 10776
ap1g2 10116
ap3g1 10156
ap3g2 11276
ap801 7444
ap802 8848
c1130 5092
c1140 10008
c1250 7184
c1520 8288
c602i 3756
Secondary AP Image Size
ap3g1 5792
ap801 5192
ap802 5232
c1100 3084
c1130 4964
c1140 4992
c1200 3364
c1240 4812
c1250 5504
c1310 3136
c1520 6404
c3201 4324
c602i 3716
Switch Configuration
802.3x Flow Control Mode......................... Disable
FIPS prerequisite features....................... Disabled
secret obfuscation............................... Enabled
Strong Password Check Features
case-check.................................... Enabled
consecutive-check............................. Enabled
default-check................................. Enabled
username-check................................ Enabled
position-check................................ Disabled
case-digit-check.............................. Disabled
Min. Password length.......................... 3
Min. Upper case chars......................... 0
Min. Lower case chars......................... 0
Min. Digits chars............................. 0
Min. Special chars............................ 0
Mgmt User
Password Lifetime [days]...................... 0
Password Lockout.............................. Disabled
Lockout Attempts.............................. 0
Lockout Timeout [mins]........................ 0
SNMPv3 User
Password Lifetime [days]...................... 0
Password Lockout.............................. Disabled
Lockout Attempts.............................. 3
Lockout Timeout [mins]........................ 5
Network Information
RF-Network Name............................. cont
Web Mode.................................... Enable
Secure Web Mode............................. Enable
Secure Web Mode Cipher-Option High.......... Disable
Secure Web Mode Cipher-Option SSLv2......... Disable
Secure Web Mode RC4 Cipher Preference....... Disable
OCSP........................................ Disabled
OCSP responder URL..........................
Secure Shell (ssh).......................... Enable
Telnet...................................... Disable
Ethernet Multicast Forwarding............... Disable
Ethernet Broadcast Forwarding............... Disable
IPv4 AP Multicast/Broadcast Mode............ Multicast Address : 0.0.0.0
IGMP snooping............................... Disabled
IGMP timeout................................ 60 seconds
IGMP Query Interval......................... 20 seconds
MLD snooping................................ Disabled
MLD timeout................................. 60 seconds
MLD query interval.......................... 20 seconds
User Idle Timeout........................... 300 seconds
ARP Idle Timeout............................ 300 seconds
Cisco AP Default Master..................... Enabled
AP Join Priority............................ Disable
Mgmt Via Wireless Interface................. Disable
Mgmt Via Dynamic Interface.................. Disable
Bridge MAC filter Config.................... Enable
Bridge Security Mode........................ EAP
Mesh Full Sector DFS........................ Enable
AP Fallback ................................ Enable
Web Auth CMCC Support ...................... Disabled
Web Auth Redirect Ports .................... 80,2
Web Auth Proxy Redirect ................... Disable
Web Auth Captive-Bypass .................. Disable
Web Auth Secure Web ....................... Enable
Fast SSID Change ........................... Disabled
AP Discovery - NAT IP Only ................. Enabled
IP/MAC Addr Binding Check .................. Enabled
CCX-lite status ............................ Disable
oeap-600 dual-rlan-ports ................... Disable
oeap-600 local-network ..................... Enable
oeap-600 Split Tunneling (Printers)......... Disable
WebPortal Online Client .................... 0
mDNS snooping............................... Disabled
mDNS Query Interval......................... 15 minutes
Port Summary
STP Admin Physical Physical Link Link
Pr Type Stat Mode Mode Status Status Trap POE
1 Normal Disa Enable Auto Auto Down Enable N/A
2 Normal Forw Enable Auto 1000 Full Up Enable N/A
3 Normal Disa Enable Auto Auto Down Enable Enable (Power Off)
4 Normal Disa Enable Auto Auto Down Enable Enable (Power Off
AP Summary
Number of APs.................................... 0
Global AP User Name.............................. Not Configured
Global AP Dot1x User Name........................ Not Configured
AP Name Slots AP Model Ethernet MAC Location
Country IP Address Clients
AP Tcp-Mss-Adjust Info
AP Name TCP State MSS Size
AP Location
Total Number of AP Groups........................ 0
Site Name........................................ default-group
Site Description.................................
NAS-identifier................................... Cisco_a5:dd:24
AP Operating Class............................... Not-configured
RF Profile
2.4 GHz band.....................................
5 GHz band.......................................
WLAN ID Interface Network Admission Control Radio Pol
icy
1 management Disabled None
*AP3600 with 802.11ac Module will only advertise first 8 WLANs on 5GHz radios.
AP Name Slots AP Model Ethernet MAC Location
Port Country Priority
RF Profile
Number of RF Profiles............................ 0
Out Of Box State................................. Disabled
RF Profile Name Band Description
11n-client-only Applied
802.11a Configuration
802.11a Network.................................. Enabled
11acSupport...................................... Enabled
11nSupport....................................... Enabled
802.11a Low Band........................... Enabled
802.11a Mid Band........................... Enabled
802.11a High Band.......................... Enabled
802.11a Operational Rates
802.11a 6M Rate.............................. Mandatory
802.11a 9M Rate.............................. Supported
802.11a 12M Rate............................. Mandatory
802.11a 18M Rate............................. Supported
802.11a 24M Rate............................. Mandatory
802.11a 36M Rate............................. Supported
802.11a 48M Rate............................. Supported
802.11a 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
MCS 16....................................... Supported
MCS 17....................................... Supported
MCS 18....................................... Supported
MCS 19....................................... Supported
MCS 20....................................... Supported
MCS 21....................................... Supported
MCS 22....................................... Supported
MCS 23....................................... Supported
802.11ac MCS Settings:
Nss=1: MCS 0-9 .............................. Supported
Nss=2: MCS 0-9 .............................. Supported
Nss=3: MCS 0-9 .............................. Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Aggregation scheduler.................... Enabled
Frame Burst.............................. Automatic
Realtime Timeout..................... 10
A-MSDU Tx:
Priority 0............................... Enabled
Priority 1............................... Enabled
Priority 2............................... Enabled
Priority 3............................... Enabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Rifs Rx ..................................... Enabled
Guard Interval .............................. Any
Beacon Interval.................................. 100
CF Pollable mandatory............................ Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 36
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
Fragmentation Threshold.......................... 2346
RSSI Low Check................................... Disabled
RSSI Threshold................................... -80
TI Threshold..................................... -50
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
dfs-peakdetect................................... Enabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC:
Voice AC - Admission control (ACM)............ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice CAC Method ............................. Load-Based
Voice tspec inactivity timeout................ Disabled
CAC SIP-Voice configuration
SIP based CAC ................................ Disabled
SIP Codec Type ............................... CODEC_TYPE_G711
SIP call bandwidth ........................... 64
SIP call bandwith sample-size ................ 20
Video AC:
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Video load-based CAC mode..................... Disabled
Video CAC Method ............................. Static
CAC SIP-Video Configuration
SIP based CAC ................................ Disabled
Best-effort AC - Admission control (ACM)...... Disabled
Background AC - Admission control (ACM)....... Disabled
Maximum Number of Clients per AP Radio........... 200
802.11a Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
TxPower Update Logging......................... Off
Default 802.11a AP performance profiles
802.11a Global Interference threshold.......... 10 %
802.11a Global noise threshold................. -70 dBm
802.11a Global RF utilization threshold........ 80 %
802.11a Global throughput threshold............ 1000000 bps
802.11a Global clients threshold............... 12 clients
Default 802.11a AP monitoring
802.11a Monitor Mode........................... enable
802.11a Monitor Mode for Mesh AP Backhaul...... disable
802.11a Monitor Channels....................... Country channels
802.11a RRM Neighbor Discover Type............. Transparent
802.11a AP Coverage Interval................... 180 seconds
802.11a AP Load Interval....................... 60 seconds
802.11a AP Noise Interval...................... 180 seconds
802.11a AP Signal Strength Interval............ 60 seconds
802.11a AP Neighbor Report Interval............ 180 seconds
802.11a AP Interference Report Interval........ 120 seconds
Leader Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Update Contribution
Noise........................................ Enable
Interference................................. Enable
Load......................................... Disable
Device Aware................................. Disable
Transmit Power Assignment Leader............... Cisco_a5:dd:24 (192.168.0.250)
Last Run....................................... 361 seconds ago
Last Run Time.................................. 0 seconds
TPC Mode....................................... Version 1
TPCv2 Target RSSI.............................. -67 dBm
TPCv2 VoWLAN Guide RSSI........................ -67.0 dBm
TPCv2 SOP...................................... -85.0 dBm
TPCv2 Default Client Ant Gain.................. 0.0 dBi
TPCv2 Path Loss Decay Factor................... 3.6
TPCv2 Search Intensity......................... 10 Iterations
AP Name Channel TxPower Allowed Power Levels
Coverage Hole Detection
802.11a Coverage Hole Detection Mode........... Enabled
802.11a Coverage Voice Packet Count............ 100 packets
802.11a Coverage Voice Packet Percentage....... 50%
802.11a Coverage Voice RSSI Threshold.......... -80 dBm
802.11a Coverage Data Packet Count............. 50 packets
802.11a Coverage Data Packet Percentage........ 50%
802.11a Coverage Data RSSI Threshold........... -80 dBm
802.11a Global coverage exception level........ 25 %
802.11a Global client minimum exception lev.... 3 clients
Leader Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Update Contribution
Noise........................................ Enable
Noise........................................ Enable
Load......................................... Disable
Device Aware................................. Disable
CleanAir Event-driven RRM option............... Disabled
CleanAir Event-driven RRM sensitivity.......... Medium
Channel Assignment Leader...................... Cisco_a5:dd:24 (192.168.0.250)
Last Run....................................... 361 seconds ago
Last Run Time.................................. 0 seconds
DCA Sensitivity Level.......................... STARTUP (5 dB)
DCA 802.11n/ac Channel Width................... 20 MHz
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11a 5 GHz Auto-RF Channel List
Allowed Channel List......................... 36,40,44,48,52,56,60,64
Unused Channel List.......................... 100,104,108,112,116,120,124,
128,132,136,140
DCA Outdoor AP option.......................... Disabled
802.11a Radio RF Grouping
RF Group Name.................................. cont
RF Protocol Version(MIN)....................... 30(30)
RF Packet Header Version....................... 2
Group Role(Mode)............................... LEADER(AUTO)
Group State.................................... Idle
Group Update Interval.......................... 600 seconds
Group Leader................................... Cisco_a5:dd:24 (192.168.0.250)
Group Member
................................. Cisco_a5:dd:24 (192.168.0.250)
Maximum/Current number of Group Member......... 20/1
Maximum/Current number of AP................... 500/0
Last Run....................................... 361 seconds ago
802.11a CleanAir Configuration
Clean Air Solution............................... Disabled
Air Quality Settings:
Air Quality Reporting........................ Enabled
Air Quality Reporting Period (min)........... 15
Air Quality Alarms........................... Enabled
Air Quality Alarm Threshold................ 35
Unclassified Interference.................. Disabled
Unclassified Severity Threshold............ 20
Interference Device Settings:
Interference Device Reporting................ Enabled
Interference Device Types:
TDD Transmitter.......................... Enabled
Jammer................................... Enabled
Continuous Transmitter................... Enabled
DECT-like Phone.......................... Enabled
Video Camera............................. Enabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Enabled
Canopy................................... Enabled
WiMax Mobile............................. Enabled
WiMax Fixed.............................. Enabled
Interference Device Alarms................... Enabled
Interference Device Types Triggering Alarms:
TDD Transmitter.......................... Disabled
Jammer................................... Enabled
Continuous Transmitter................... Disabled
DECT-like Phone.......................... Disabled
Video Camera............................. Disabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Disabled
Canopy................................... Disabled
WiMax Mobile............................. Disabled
WiMax Fixed.............................. Disabled
Additional Clean Air Settings:
CleanAir ED-RRM State........................ Disabled
CleanAir ED-RRM Sensitivity.................. Medium
CleanAir ED-RRM Custom Threshold............. 50
CleanAir Persistent Devices state............ Disabled
CleanAir Persistent Device Propagation....... Disabled
802.11a CleanAir AirQuality Summary
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name Channel Avg AQ Min AQ Interferers DFS
802.11b Configuration
802.11b Network.................................. Enabled
11gSupport....................................... Enabled
11nSupport....................................... Enabled
802.11b/g Operational Rates
802.11b/g 1M Rate............................ Mandatory
802.11b/g 2M Rate............................ Mandatory
802.11b/g 5.5M Rate.......................... Mandatory
802.11b/g 11M Rate........................... Mandatory
802.11g 6M Rate.............................. Supported
802.11g 9M Rate.............................. Supported
802.11g 12M Rate............................. Supported
802.11g 18M Rate............................. Supported
802.11g 24M Rate............................. Supported
802.11g 36M Rate............................. Supported
802.11g 48M Rate............................. Supported
802.11g 54M Rate............................. Supported
802.11n MCS Settings:
MCS 0........................................ Supported
MCS 1........................................ Supported
MCS 2........................................ Supported
MCS 3........................................ Supported
MCS 4........................................ Supported
MCS 5........................................ Supported
MCS 6........................................ Supported
MCS 7........................................ Supported
MCS 8........................................ Supported
MCS 9........................................ Supported
MCS 10....................................... Supported
MCS 11....................................... Supported
MCS 12....................................... Supported
MCS 13....................................... Supported
MCS 14....................................... Supported
MCS 15....................................... Supported
MCS 16....................................... Supported
MCS 17....................................... Supported
MCS 18....................................... Supported
MCS 19....................................... Supported
MCS 20....................................... Supported
MCS 21....................................... Supported
MCS 22....................................... Supported
MCS 23....................................... Supported
802.11n Status:
A-MPDU Tx:
Priority 0............................... Enabled
Priority 1............................... Disabled
Priority 2............................... Disabled
Priority 3............................... Disabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Aggregation scheduler.................... Enabled
Realtime Timeout..................... 10
A-MSDU Tx:
Priority 0............................... Enabled
Priority 1............................... Enabled
Priority 2............................... Enabled
Priority 3............................... Enabled
Priority 4............................... Enabled
Priority 5............................... Enabled
Priority 6............................... Disabled
Priority 7............................... Disabled
Rifs Rx ..................................... Enabled
Guard Interval .............................. Any
Beacon Interval.................................. 100
CF Pollable mode................................. Disabled
CF Poll Request mandatory........................ Disabled
CFP Period....................................... 4
CFP Maximum Duration............................. 60
Default Channel.................................. 1
Default Tx Power Level........................... 0
DTPC Status..................................... Enabled
RSSI Low Check................................... Disabled
RSSI Threshold................................... -80
Call Admission Limit ........................... 105
G711 CU Quantum ................................. 15
ED Threshold..................................... -50
Fragmentation Threshold.......................... 2346
PBCC mandatory................................... Disabled
RTS Threshold.................................... 2347
Short Preamble mandatory......................... Enabled
Short Retry Limit................................ 7
Legacy Tx Beamforming setting.................... Disabled
Traffic Stream Metrics Status.................... Disabled
Expedited BW Request Status...................... Disabled
World Mode....................................... Enabled
Faster Carrier Tracking Loop..................... Disabled
EDCA profile type................................ default-wmm
Voice MAC optimization status.................... Disabled
Call Admission Control (CAC) configuration
Voice AC - Admission control (ACM)............ Disabled
Voice Stream-Size............................. 84000
Voice Max-Streams............................. 2
Voice max RF bandwidth........................ 75
Voice reserved roaming bandwidth.............. 6
Voice CAC Method.............................. Load-Based
Voice tspec inactivity timeout................ Disabled
CAC SIP-Voice configuration
SIP based CAC ................................ Disabled
SIP Codec Type ............................... CODEC_TYPE_G711
SIP call bandwidth: .......................... 64
SIP call bandwidth sample-size ............... 20
Video AC - Admission control (ACM)............ Disabled
Video max RF bandwidth........................ Infinite
Video reserved roaming bandwidth.............. 0
Video load-based CAC mode..................... Disabled
Video CAC Method ............................. Static
CAC SIP-Video configuration
SIP based CAC ................................ Disabled
Best-effort AC - Admission control (ACM)...... Disabled
Background AC - Admission control (ACM)....... Disabled
Maximum Number of Clients per AP................. 200
802.11b Airewave Director Configuration
RF Event and Performance Logging
Channel Update Logging......................... Off
Coverage Profile Logging....................... Off
Foreign Profile Logging........................ Off
Load Profile Logging........................... Off
Noise Profile Logging.......................... Off
Performance Profile Logging.................... Off
Transmit Power Update Logging.................. Off
Default 802.11b AP performance profiles
802.11b Global Interference threshold.......... 10 %
802.11b Global noise threshold................. -70 dBm
802.11b Global RF utilization threshold........ 80 %
802.11b Global throughput threshold............ 1000000 bps
802.11b Global clients threshold............... 12 clients
Default 802.11b AP monitoring
802.11b Monitor Mode........................... enable
802.11b Monitor Channels....................... Country channels
802.11b RRM Neighbor Discovery Type............ Transparent
802.11b AP Coverage Interval................... 180 seconds
802.11b AP Load Interval....................... 60 seconds
802.11b AP Noise Interval...................... 180 seconds
802.11b AP Signal Strength Interval............ 60 seconds
802.11b AP Neighbor Report Interval............ 180 seconds
802.11b AP Interference Report Interval........ 120 seconds
Leader Automatic Transmit Power Assignment
Transmit Power Assignment Mode................. AUTO
Transmit Power Update Interval................. 600 seconds
Transmit Power Threshold....................... -70 dBm
Transmit Power Neighbor Count.................. 3 APs
Min Transmit Power............................. -10 dBm
Max Transmit Power............................. 30 dBm
Update Contribution
Noise........................................ Enable
Interference................................. Enable
Load......................................... Disable
Device Aware................................. Disable
Transmit Power Assignment Leader............... Cisco_a5:dd:24 (192.168.0.250)
Last Run....................................... 490 seconds ago
Last Run Time.................................. 0 seconds
TPC Mode....................................... Version 1
TPCv2 Target RSSI.............................. -67 dBm
TPCv2 VoWLAN Guide RSSI........................ -67.0 dBm
TPCv2 SOP...................................... -85.0 dBm
TPCv2 Default Client Ant Gain.................. 0.0 dBi
TPCv2 Path Loss Decay Factor................... 3.6
TPCv2 Search Intensity......................... 10 Iterations
AP Name Channel TxPower Allowed Power Levels
Coverage Hole Detection
802.11b Coverage Hole Detection Mode........... Enabled
802.11b Coverage Voice Packet Count............ 100 packets
802.11b Coverage Voice Packet Percentage....... 50%
802.11b Coverage Voice RSSI Threshold.......... -80 dBm
802.11b Coverage Data Packet Count............. 50 packets
802.11b Coverage Data Packet Percentage........ 50%
802.11b Coverage Data RSSI Threshold........... -80 dBm
802.11b Global coverage exception level........ 25 %
802.11b Global client minimum exception lev.... 3 clients
Leader Automatic Channel Assignment
Channel Assignment Mode........................ AUTO
Channel Update Interval........................ 600 seconds [startup]
Anchor time (Hour of the day).................. 0
Update Contribution
Noise........................................ Enable
Interference................................. Enable
Load......................................... Disable
Device Aware................................. Disable
CleanAir Event-driven RRM option............... Disabled
CleanAir Event-driven RRM sensitivity.......... Medium
Channel Assignment Leader...................... Cisco_a5:dd:24 (192.168.0.250)
Last Run....................................... 523 seconds ago
Last Run Time.................................. 0 seconds
DCA Sensitivity Level: ...................... STARTUP (5 dB)
DCA Minimum Energy Limit....................... -95 dBm
Channel Energy Levels
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
Channel Dwell Times
Minimum...................................... unknown
Average...................................... unknown
Maximum...................................... unknown
802.11b Auto-RF Allowed Channel List........... 1,5,9,13
Auto-RF Unused Channel List.................... 2,3,4,6,7,8,10,11,12
802.11b Radio RF Grouping
RF Group Name.................................. cont
RF Protocol Version(MIN)....................... 30(30)
RF Packet Header Version....................... 2
Group Role(Mode)............................... LEADER(AUTO)
Group State.................................... Idle
Group Update Interval.......................... 600 seconds
Group Leader................................... Cisco_a5:dd:24 (192.168.0.250)
Group Member
................................. Cisco_a5:dd:24 (192.168.0.250)
Maximum/Current number of Group Member......... 20/1
Maximum/Current number of AP................... 500/0
Last Run....................................... 523 seconds ago
802.11b CleanAir Configuration
Clean Air Solution............................... Disabled
Air Quality Settings:
Air Quality Reporting........................ Enabled
Air Quality Reporting Period (min)........... 15
Air Quality Alarms........................... Enabled
Air Quality Alarm Threshold................ 35
Unclassified Interference.................. Disabled
Unclassified Severity Threshold............ 20
Interference Device Settings:
Interference Device Reporting................ Enabled
Interference Device Types:
Bluetooth Link........................... Enabled
Microwave Oven........................... Enabled
802.11 FH................................ Enabled
Bluetooth Discovery...................... Enabled
TDD Transmitter.......................... Enabled
Jammer................................... Enabled
Continuous Transmitter................... Enabled
DECT-like Phone.......................... Enabled
Video Camera............................. Enabled
802.15.4................................. Enabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Enabled
Canopy................................... Enabled
Microsoft Device......................... Enabled
WiMax Mobile............................. Enabled
WiMax Fixed.............................. Enabled
Interference Device Alarms................... Enabled
Interference Device Types Triggering Alarms:
Bluetooth Link........................... Disabled
Microwave Oven........................... Disabled
802.11 FH................................ Disabled
Bluetooth Discovery...................... Disabled
TDD Transmitter.......................... Disabled
Jammer................................... Enabled
Continuous Transmitter................... Disabled
DECT-like Phone.......................... Disabled
Video Camera............................. Disabled
802.15.4................................. Disabled
WiFi Inverted............................ Enabled
WiFi Invalid Channel..................... Enabled
SuperAG.................................. Disabled
Canopy................................... Disabled
Microsoft Device......................... Disabled
WiMax Mobile............................. Disabled
WiMax Fixed.............................. Disabled
Additional Clean Air Settings:
CleanAir ED-RRM State........................ Disabled
CleanAir ED-RRM Sensitivity.................. Medium
CleanAir ED-RRM Custom Threshold............. 50
CleanAir Persistent Devices state............ Disabled
CleanAir Persistent Device Propagation....... Disabled
802.11a CleanAir AirQuality Summary
AQ = Air Quality
DFS = Dynamic Frequency Selection
AP Name Channel Avg AQ Min AQ Interferers DFS
Mobility Configuration
Mobility Protocol Port........................... 16666
Default Mobility Domain.......................... cont
Multicast Mode .................................. Disabled
Mobility Domain ID for 802.11r................... 0xe3e
Mobility Keepalive Interval...................... 10
Mobility Keepalive Count......................... 3
Mobility Group Members Configured................ 1
Mobility Control Message DSCP Value.............. 0
Controllers configured in the Mobility Group
MAC Address IP Address Group Name
Multicast IP Status
10:f3:11:a5:dd:20 192.168.0.250 cont
0.0.0.0 Up
Mobility Hash Configuration
Default Mobility Domain.......................... cont
IP Address Hash Key
Self Signed Certificate details
SSC Hash validation.............................. Enabled.
SSC device certificate not present.
Mobility Foreign Map Configuration
WLAN ID Foreign Mac Address Interface
Advanced Configuration
Probe request filtering.......................... Enabled
Probes fwd to controller per client per radio.... 2
Probe request rate-limiting interval............. 500 msec
Aggregate Probe request interval................. 0 msec
Increased backoff parameters for probe respon.... Disabled
EAP-Identity-Request Timeout (seconds)........... 30
EAP-Identity-Request Max Retries................. 2
EAP Key-Index for Dynamic WEP.................... 0
EAP Max-Login Ignore Identity Response........... enable
EAP-Request Timeout (seconds).................... 30
EAP-Request Max Retries.......................... 2
EAPOL-Key Timeout (milliseconds)................. 1000
EAPOL-Key Max Retries............................ 2
EAP-Broadcast Key Interval....................... 3600
Fastpath Packet Capture.......................... disable
Fastpath Fast Cache Control...................... enable
Fastpath Fast Testmode........................... 0x0
dot11-padding.................................... Disabled
Advanced Hotspot Commands
ANQP 4-way state................................. Disabled
GARP Broadcast state: ........................... Enabled
GAS request rate limit .......................... Disabled
ANQP comeback delay in TUs(TU=1024usec).......... 50
Location Configuration
RFID Tag data Collection......................... Enabled
RFID timeout.................................... 1200 seconds
RFID mobility....................................
Interface Configuration
Interface Name................................... ap-management1
MAC Address...................................... 10:f3:11:a5:dd:24
IP Address....................................... 192.168.0.251
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.7
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
NAS-Identifier................................... Cisco_a5:dd:24
Active Physical Port............................. 1
Primary Physical Port............................ 1
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.0.7
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
Interface Name................................... ap-management3
MAC Address...................................... 10:f3:11:a5:dd:26
IP Address....................................... 192.168.0.253
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.7
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
NAS-Identifier................................... Cisco_a5:dd:24
Active Physical Port............................. 3
Primary Physical Port............................ 3
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.0.7
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
Interface Name................................... ap-management4
MAC Address...................................... 10:f3:11:a5:dd:27
IP Address....................................... 192.168.0.254
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.7
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
NAS-Identifier................................... Cisco_a5:dd:24
Active Physical Port............................. 4
Primary Physical Port............................ 4
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.0.7
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Enabled
Interface Name................................... management
MAC Address...................................... 10:f3:11:a5:dd:20
IP Address....................................... 192.168.0.250
IP Netmask....................................... 255.255.255.0
IP Gateway....................................... 192.168.0.7
External NAT IP State............................ Disabled
External NAT IP Address.......................... 0.0.0.0
VLAN............................................. untagged
Quarantine-vlan.................................. 0
Active Physical Port............................. 2
Primary Physical Port............................ 2
Backup Physical Port............................. Unconfigured
DHCP Proxy Mode.................................. Global
Primary DHCP Server.............................. 192.168.0.7
Secondary DHCP Server............................ Unconfigured
DHCP Option 82................................... Disabled
IPv4 ACL......................................... Unconfigured
IPv6 ACL......................................... Unconfigured
mDNS Profile Name................................ Unconfigured
AP Manager....................................... Yes
Guest Interface.................................. No
L2 Multicast..................................... Disabled
Interface Name................................... virtual
MAC Address...................................... 10:f3:11:a5:dd:20
IP Address....................................... 1.1.1.1
Virtual DNS Host Name............................ Disabled
AP Manager....................................... No
Guest Interface.................................. No
Interface Group Configuration
WLAN Configuration
WLAN Identifier.................................. 1
Profile Name..................................... kisan
Network Name (SSID).............................. kisan
Status........................................... Enabled
MAC Filtering.................................... Disabled
Broadcast SSID................................... Enabled
AAA Policy Override.............................. Disabled
Network Admission Control
Client Profiling Status
Radius Profiling ............................ Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Local Profiling ............................. Disabled
DHCP ....................................... Disabled
HTTP ....................................... Disabled
Radius-NAC State............................... Disabled
SNMP-NAC State................................. Disabled
Quarantine VLAN................................ 0
Maximum number of Associated Clients............. 0
Maximum number of Clients per AP Radio........... 200
Number of Active Clients......................... 0
Exclusionlist Timeout............................ 60 seconds
Session Timeout.................................. 1800 seconds
User Idle Timeout................................ Disabled
Sleep Client..................................... disable
Sleep Client Timeout............................. 12 hours
User Idle Threshold.............................. 0 Bytes
NAS-identifier................................... Cisco_a5:dd:24
CHD per WLAN..................................... Enabled
Webauth DHCP exclusion........................... Disabled
Interface........................................ management
Multicast Interface.............................. Not Configured
WLAN IPv4 ACL.................................... unconfigured
WLAN IPv6 ACL.................................... unconfigured
WLAN Layer2 ACL.................................. unconfigured
mDNS Status...................................... Enabled
mDNS Profile Name................................ default-mdns-profile
DHCP Server...................................... Default
DHCP Address Assignment Required................. Disabled
Static IP client tunneling....................... Disabled
Quality of Service............................... Silver
Per-SSID Rate Limits............................. Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Per-Client Rate Limits........................... Upstream Downstream
Average Data Rate................................ 0 0
Average Realtime Data Rate....................... 0 0
Burst Data Rate.................................. 0 0
Burst Realtime Data Rate......................... 0 0
Scan Defer Priority.............................. 4,5,6
Scan Defer Time.................................. 100 milliseconds
WMM.............................................. Allowed
WMM UAPSD Compliant Client Support............... Disabled
Media Stream Multicast-direct.................... Disabled
CCX - AironetIe Support.......................... Enabled
CCX - Gratuitous ProbeResponse (GPR)............. Disabled
CCX - Diagnostics Channel Capability............. Disabled
Dot11-Phone Mode (7920).......................... Disabled
Wired Protocol................................... None
Passive Client Feature........................... Disabled
Peer-to-Peer Blocking Action..................... Disabled
Radio Policy..................................... All
DTIM period for 802.11a radio.................... 1
DTIM period for 802.11b radio.................... 1
Radius Servers
Authentication................................ Global Servers
Accounting.................................... Global Servers
Interim Update............................. Disabled
Framed IPv6 Acct AVP ...................... Prefix
Dynamic Interface............................. Disabled
Dynamic Interface Priority.................... wlan
Local EAP Authentication......................... Disabled
Security
802.11 Authentication:........................ Open System
FT Support.................................... Disabled
Static WEP Keys............................... Disabled
802.1X........................................ Disabled
Wi-Fi Protected Access (WPA/WPA2)............. Enabled
WPA (SSN IE)............................... Disabled
WPA2 (RSN IE).............................. Enabled
TKIP Cipher............................. Disabled
AES Cipher.............................. Enabled
Auth Key Management
802.1x.................................. Enabled
PSK..................................... Disabled
CCKM.................................... Disabled
FT-1X(802.11r).......................... Disabled
FT-PSK(802.11r)......................... Disabled
PMF-1X(802.11w)......................... Disabled
PMF-PSK(802.11w)........................ Disabled
FT Reassociation Timeout................... 20
FT Over-The-DS mode........................ Enabled
GTK Randomization.......................... Disabled
SKC Cache Support.......................... Disabled
CCKM TSF Tolerance......................... 1000
WAPI.......................................... Disabled
Wi-Fi Direct policy configured................ Disabled
EAP-Passthrough............................... Disabled
CKIP ......................................... Disabled
Web Based Authentication...................... Disabled
Web-Passthrough............................... Disabled
Conditional Web Redirect...................... Disabled
Splash-Page Web Redirect...................... Disabled
Auto Anchor................................... Disabled
FlexConnect Local Switching................... Disabled
flexconnect Central Dhcp Flag................. Disabled
flexconnect nat-pat Flag...................... Disabled
flexconnect Dns Override Flag................. Disabled
flexconnect PPPoE pass-through................ Disabled
flexconnect local-switching IP-source-guar.... Disabled
FlexConnect Vlan based Central Switching ..... Disabled
FlexCo
Similar Messages
-
Dear All,
I cannot connect to my Exchange account in Outlook 2013 using "Microsoft Exchange Server or Compatible Service".
First I would like to present my network environment, I have 4 physical servers;
The first one is holding the Domain Controller 1, IP@: 192.168.1.10
The second server is holding the additional Domain Controller which it is DC2, IP@: 192.168.1.11
The third server is holding the Exchange 2013 Mailbox, IP@: 192.168.1.15
And the last server is holding the Exchange 2013 CAS-HT, IP@: 192.168.1.16
I am doing the steps below:
1-Creating a new profile in outlook and start configuring the exchange account by entering the IP address of the Exchange-CAS Server, 192.168.1.16
2-entering the account name: [email protected]
3-Go to "More Settings" > "Connection" > "Connect to Microsoft Exchange using HTTP" > and entering the "Exchange Proxy Settings"
4-type the exchange CAS Server URL, https://192.168.1.16
5-Check the "Connect using SSL Only"
6-Authentication Settings: "NTLM Authentication", and pressing Apply
7-When I press the "Check Name" button, a message occurred> "The action cannot be completed. The connection to Microsoft Exchange is unavailable. Outlook must be online or connected to complete this action".
8-I go back to the "Exchange Proxy Settings" and I Uncheck the "Connect using SSL Only" and pressing Apply
9-i press the "Check Name" Button, a small window occurred to enter a Username and Password, so I enter the Administrator username and the administrator password and pressing "OK", but nothing is changed, I tried to enter my
username and password in the small window and I still got the same result.
I cannot verify the account name and I cannot complete the process.
I appreciate you kind assistance.Hi,
To narrow down the cause, I’d like to recommend the following troubleshooting:
1. Try to login the test account through OWA.
2. Check the Autodiscover settings: get-clientaccessserver |fl autodiscoverserviceinternaluri
3. Check the result of directly accessing the following URL:
https://autodiscover.domain.com/autodiscover/autodiscover.xml
Thanks,
Angela
Angela Shi
TechNet Community Support -
I - STILL - Cannot connect to the Itunes Store
I am unable to connect to the Itunes store, I could connect to the radio stations, I checked the SSL and TSL setting under Internet Explorer Options, Not using proxy or any Computer based firewall, and on my router firewall I tried opening up ports 53, 5353, 443 and 3689, and even tried DMZ the box, but for no use... I still cannot connect to the store, and frankly, it is getting ridiculous. Can anyone help? maybe the neededs ports or something...
Here is the check log... and thanks in advance.
Microsoft Windows XP Professional Service Pack 2 (Build 2600)
Dell Inc. Dimension XPS
iTunes 7.6.1.9
QuickTime 7.4.1
CD Driver 2.0.6.1
CD Driver DLL 2.0.6.2
Apple Mobile Device 1.1.4.7
Bonjour 1.0.4.12 (118.4)
iTunes Serial Number 3A48AA7B3CB9DD57
Current user is an administrator.
The current local date and time is 2008-03-08 21:11:11.
iTunes is not running in safe mode.
Video Display Information
NVIDIA GeForce 6800
External Plug-ins Information **
No external plug-ins installed.
Network Connectivity Tests **
Network Adapter Information
Adapter Name: {686274E4-CF42-4229-98AE-678EE8BF1331}
Description: Broadcom NetXtreme 57xx Gigabit Controller - Packet Scheduler Miniport
IP Address: 10.10.0.10
Subnet Mask: 255.255.255.0
Default Gateway: 10.10.0.1
DHCP Enabled: No
DHCP Server: 255.255.255.255
Lease Obtained: Wed Dec 31 20:00:00 1969
Lease Expires: Wed Dec 31 20:00:00 1969
DNS Servers: 10.10.0.1
10.10.0.1
Adapter Name: {C7089E37-5C18-4224-812A-541BFED730B6}
Description: VMware Virtual Ethernet Adapter for VMnet1
IP Address: 192.168.181.1
Subnet Mask: 255.255.255.0
Default Gateway:
DHCP Enabled: No
DHCP Server: 255.255.255.255
Lease Obtained: Wed Dec 31 20:00:00 1969
Lease Expires: Wed Dec 31 20:00:00 1969
DNS Servers:
Adapter Name: {F5345F4B-2E32-4D97-BB78-741CFE4A155C}
Description: VMware Virtual Ethernet Adapter for VMnet8
IP Address: 192.168.92.1
Subnet Mask: 255.255.255.0
Default Gateway:
DHCP Enabled: No
DHCP Server: 255.255.255.255
Lease Obtained: Wed Dec 31 20:00:00 1969
Lease Expires: Wed Dec 31 20:00:00 1969
DNS Servers:
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
SSL 3.0 Support: Enabled
TLS 1.0 Support: Enabled
Firewall Information
Windows Firewall is off.
Connection attempt to Apple web site was successful.
Connection attempt to iTunes Store was successful.
Secure connection attempt to iTunes Store was successful.
Secure connection attempt to iPhone activation server was successful.
iTunes has never successfully accessed iTunes store.I don't think it is a firewall issue as the connection attempts were not blocked according to the network connectivity report.
These ones have been tricky to solve.
As a first stab, one thing you could try is to create a new Windows account and see if you can connect from there.
P.S. I noticed that the date on the report is not the same as the date of your post. This may just be when your ran the report, but it is worth checking your computer's date and time are correct.
You could also check the Advanced tab in your Internet options. If "Check for server certificate revocation" is checked. If it is, try unchecking it.
Message was edited by: polydorus -
Help...downloaded new version of itunes...and now I cannot connect
I just downloaded new version of itunes and now I cannot connect to the itunes store...I get a message that says..."Itunes cannot connect to itunes store. the network connection timed out."
ran diagnostics here are the results... if anyone can help...
Microsoft Windows Vista Home Premium Edition (Build 6000)
Hewlett-Packard Presario F700 (GR967UA#ABA)
iTunes 8.2.0.23
QuickTime 7.6.2
FairPlay 1.4.10
iPod Updater Library 8.1d19
CD Driver 2.1.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 2.5.0.31
Apple Mobile Device Driver not found.
Bonjour 1.0.6.2 (118.5)
iTunes Serial Number D3C70EE5E29DDAC2
Current user is not an administrator.
The current local date and time is 2009-06-09 23:19:03.
iTunes is not running in safe mode.
Video Display Information
NVIDIA, NVIDIA GeForce Go 6100
** External Plug-ins Information **
No external plug-ins installed.
** Network Connectivity Tests **
Network Adapter Information
Adapter Name: {C07101F5-89CB-4921-9239-F59263AF4FAA}
Description: Broadcom 802.11b/g WLAN
IP Address: 192.168.1.2
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
DHCP Enabled: Yes
DHCP Server: 192.168.1.1
Lease Obtained: Tue Jun 09 22:30:17 2009
Lease Expires: Wed Jun 10 22:30:17 2009
DNS Servers: 192.168.1.1
192.168.1.1
Adapter Name: {33E3719A-76B1-48B1-9F31-BD3CBF2DBDDA}
Description: NVIDIA nForce Networking Controller
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
SSL 3.0 Support: Enabled
TLS 1.0 Support: Enabled
Firewall Information
Windows Firewall is on.
iTunes is enabled in Windows Firewall.
Connection attempt to Apple web site was unsuccessful.
The network connection timed out.
Connection attempt to iTunes Store was unsuccessful.
The network connection timed out.
Secure connection attempt to iTunes Store was unsuccessful.
The network connection timed out.
Secure connection attempt to iPhone activation server unsuccessful.
The network connection timed out.
Last successful store access was 2009-06-08 09:41:24.
** CD/DVD Drive Tests **
LowerFilters: PxHelp20 (2.0.0.0),
UpperFilters: GEARAspiWDM (2.1.0.1),
E: TSSTcorp CD/DVDW TS-L632M, Rev 0A17
Audio CD in drive.
Found 1 songs on CD, playing time 04:24 on Audio CD.
Track 1, start time 00:02:00
Audio CD reading succeeded.
Get drive speed succeeded.
The drive CDR speeds are: 4 10 16 20 24.
The drive CDRW speeds are: 4.
The drive DVDR speeds are: 4.
The drive DVDRW speeds are: 4.
** iPod/iPhone Connectivity Tests **
iPodService 8.2.0.23 is currently running.
iTunesHelper 8.2.0.23 is currently running.
Apple Mobile Device service 2.50.39.0 is currently running.
Universal Serial Bus Controllers:
Standard OpenHCD USB Host Controller. Device is working properly.
Standard Enhanced PCI to USB Host Controller. Device is working properly.
No FireWire (IEEE 1394) Host Controller found.
Most Recent Device Not Currently Connected:
iPod nano (Second Generation) running firmware version 1.1.1
Serial Number: 7J651R7ZVQ5
** iPhone/iPod Touch Sync Tests **
No iPhone or iPod found.Are you running any of Symantec's (Norton) or McAfee's Internet security products or anything similar, or an antivirus/antispyware application? There have been reports that some such utilities treat an upgrade to iTunes as a new application and can block the application from connecting. So you have to go in and reset the utility to allow iTunes. The same thing can happen if you upgrade the security product (this has particularly been a problem with recent McAfee upgrades).
Check the settings for your utility. If iTunes is still listed, remove and re-enable the exception for iTunes. Consult your utility's documentation for the appropriate procedure; you can find instructions for Norton on Symantec's web page for iTunes. You may also need to check the built-in Windows firewall as well.
Hope this helps. -
Moved PC to another country - now cannot connect to iTunes store
Hi - I have a UK iTunes account and I have moved my PC to Switzerland. I tried to update my iTunes and iPod, yet now I cannot connect to the iTunes store.
Can anyone please help?
Thanks,
JCOk here goes. I've taken out any serial number or IP address.
Microsoft Windows XP Professional Service Pack 3 (Build 2600)
eveshamvale 965X7AA
iTunes 8.2.0.23
QuickTime 7.6.2
FairPlay 1.4.10
iPod Updater Library 8.1d19
CD Driver 2.1.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 2.5.0.31
Apple Mobile Device Driver 1.43.0.0
Bonjour 1.0.6.2
Current user is an administrator.
The current local date and time is 2009-06-03 21:43:02.
iTunes is not running in safe mode.
Video Display Information
NVIDIA GeForce 8800 GTX
** External Plug-ins Information **
No external plug-ins installed.
** Network Connectivity Tests **
Network Adapter Information
Adapter Name: {E34BB18D-1AFA-436F-B879-AB44E6DB3DAA}
Description: Generic Marvell Yukon Chipset based Ethernet Controller - Packet Scheduler Miniport
IP Address: <snip>
Subnet Mask: <snip>
Default Gateway: <snip>
DHCP Enabled: Yes
DHCP Server: <snip>
Lease Obtained: Wed Jun 03 21:25:18 2009
Lease Expires: Thu Jun 04 21:25:18 2009
DNS Servers: <snip>
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
SSL 3.0 Support: Enabled
TLS 1.0 Support: Enabled
Firewall Information
Windows Firewall is off.
Connection attempt to Apple web site was unsuccessful.
The network connection timed out.
Connection attempt to iTunes Store was unsuccessful.
An unknown error occurred (-28).
Secure connection attempt to iTunes Store was unsuccessful.
An unknown error occurred (-28).
Secure connection attempt to iPhone activation server unsuccessful.
An unknown error occurred (-28).
Last successful store access was 2009-06-02 17:04:05. -
ITunes cannot connect to internet
So I can't use my new ipod touch without connecting to the itunes store. I've disabled all my firewalls, yet I still cannot connect to the itunes store. I run the network diagnostics and it fails, but when I click the help button, I see "iTunes Help is unavailable because your computer isn’t connected to the Internet."
Again I have no firewalls running, so how is it that my iTunes program can't connect to the internet?
Message was edited by: sevenand7is27Here is my diagnostics report:
Microsoft Windows 7 x64 Business Edition (Build 7600)
Dell Inc. XPS L501X
iTunes 10.2.1.1
QuickTime 7.6.9
FairPlay 1.11.16
Apple Application Support 1.5
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.0.25
Apple Mobile Device Driver 1.55.0.0
Bonjour 2.0.4.0 (214.3)
Gracenote SDK 1.8.2.457
Gracenote MusicID 1.8.2.89
Gracenote Submit 1.8.2.123
Gracenote DSP 1.8.2.34
iTunes Serial Number 002EAAA003273248
Current user is an administrator.
The current local date and time is 2011-04-02 17:57:05.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
Video Display Information
NVIDIA, NVIDIA GeForce GT 435M
** External Plug-ins Information **
No external plug-ins installed.
iPodService 10.2.1.1 (x64) is currently running.
iTunesHelper 10.2.1.1 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
** Network Connectivity Tests **
Network Adapter Information
Adapter Name: {8C3879FE-7D82-4037-8235-F3332C2DE675}
Description: Intel(R) Centrino(R) WiMAX 6250
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Adapter Name: {970637EA-A21C-47EA-9DC0-96CED2B5C5C0}
Description: Microsoft Virtual WiFi Miniport Adapter #2
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Adapter Name: {0163DCB4-D946-453E-AA28-D783FB23D9E5}
Description: Microsoft Virtual WiFi Miniport Adapter
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Adapter Name: {B67D488B-BF51-4233-ABEC-6B38E579390C}
Description: Bluetooth Device (Personal Area Network)
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Adapter Name: {3D2C00C4-389A-4CF3-8196-B08B35A09CD1}
Description: Intel(R) Centrino(R) Advanced-N 6250 AGN
IP Address: 192.168.1.12
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
DHCP Enabled: Yes
DHCP Server: 192.168.1.1
Lease Obtained: Sat Apr 02 17:47:14 2011
Lease Expires: Sun Apr 03 17:47:14 2011
DNS Servers: 192.168.1.1
Adapter Name: {269D81C7-5E24-49FA-A988-2EB93BC19D25}
Description: Realtek PCIe GBE Family Controller
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: Yes
HTTP Proxy: 127.0.0.1:8118
SSL 3.0 Support: Enabled
TLS 1.0 Support: Enabled
Firewall Information
Windows Firewall is off.
Connection attempt to Apple web site was unsuccessful.
The network connection timed out.
Basic connection to the store failed.
The network connection timed out.
Connection attempt to Gracenote server was successful.
The network connection timed out.
iTunes has never successfully accessed the iTunes Store. -
Cannot connect to internet- itunes cannot make secure connection- error 3212
Got new goodies for Christmas- an ultrabook with windows 0and an iPhone 4s, my first iphone. Want to sync it and get Ipod touch apps, etc, but when I load up itunes, it says it cannot connect to the internet. Sure as I'm typing here, our internet is working. I don't have a proxy, I turned off my firewall, itunes is run as administrator, I used the winsock reset in command prompt, and the network diagnostics just says
(Build 9200)
SAMSUNG ELECTRONICS CO., LTD. 520U4C/520U4X
iTunes 11.0.1.12
QuickTime 7.7.3
FairPlay 2.2.32
Apple Application Support 2.3.2
iPod Updater Library 10.0d2
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 6.0.1.3
Apple Mobile Device Driver not found.
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 0025B6D80366EFD8
Current user is not an administrator.
The current local date and time is 2012-12-27 00:07:24.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
**** External Plug-ins Information ****
No external plug-ins installed.
iPodService 11.0.1.12 (x64) is currently running.
iTunesHelper 11.0.1.12 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name: {336F820E-2DCE-4E46-9ECA-4701676F5F4F}
Description: Microsoft Hosted Network Virtual Adapter
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Adapter Name: {7BF9434C-4E43-4AF6-B073-A33E0FCFC35A}
Description: Microsoft Wi-Fi Direct Virtual Adapter
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Adapter Name: {582A8206-4B6F-4A73-B957-368827E68829}
Description: Intel(R) Centrino(R) Advanced-N 6235
IP Address: 192.168.0.18
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.1
DHCP Enabled: Yes
DHCP Server: 192.168.0.1
Lease Obtained: Wed Dec 26 23:32:01 2012
Lease Expires: Sun Feb 16 18:18:40 2014
DNS Servers: 209.18.47.61
209.18.47.62
Adapter Name: {0ADF1741-E03F-43A0-B540-5F14C4DBA710}
Description: Bluetooth Device (Personal Area Network)
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Adapter Name: {E8B30F0C-E717-44C6-B3DB-63BF3C0204E0}
Description: Realtek PCIe GBE Family Controller
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 19:00:00 1969
Lease Expires: Wed Dec 31 19:00:00 1969
DNS Servers:
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
Firewall Information
Windows Firewall is off.
Connection attempt to Apple web site was unsuccessful.
An unknown error occurred (-3212).
Basic connection to the store failed.
An unknown error occurred (-3212).
Connection attempt to Gracenote server was successful.
An unknown error occurred (-3212).
iTunes has never successfully accessed the iTunes Store.
Help?I ran Autoruns and came back with Bonjour as the only thing on the winsock provider- it's on there twice
-
2008 R2 printer server, cannot connect to printer, access denied, Windows 7 OS only
Deployed new Windows 2008 R2 domain controller, added print and document controll. Added several network printers on R2 server. We currently have mostly Vista biz clients but half a dozen W7Pro clients also. The Vista clients connect to these new network
printers, no problem but none of the W7 clients will connect. I select the printer from the drop down directory list and select to load the drivers, the system starts loading drivers and then right before it finishes it stops with error message, "Windows cannot
connect to the printer. Access denied. Again, this happens only with the W7 clients on our domain, Vista works fine.By default, the security settings for Windows 7 and Server 2008 R2 allow users who are not members of the local
Administrators group to install only trustworthy printer drivers, such as those provided with Windows or in digitally signed printer-driver packages. You may want to install printer-driver packages on the print server
or in the clients. More details can be found this page: Cannot
connect to printer, Access denied -
http://www.chicagotech.net/server/print3.htm
Bob Lin, MS-MVP Networking, Internet, Routing, VPN Troubleshooting on
http://www.ChicagoTech.net
How to Setup Windows, Network, VPN & Remote Access on
http://www.howtonetworking.com -
Cannot connect to the configuration database
I tried to configure my server with active directory after I have successfully configured sharepoint . For a mistake , they made me delete the active directory and now when I try to connect to the admin section or site page it me give the following error :
"Cannot connect to the configuration database"
Deleting the active directory ; I noticed that all the other users have disappeared and the service : SQL AGENT ( Sharepoint ) not run and the error is :
" This installation of SQL Server Agent is disabled. The edition of SQL Server that installed this service does not support SQL Server Agent." Thank you for the HelpWas the active directory server that you removed the last active directory server in the farm? If so then your only two real choices are to rebuild everything from scratch or restore everything from backup.
If it was just that you were trying to make the SharePoint server into a Domain Controller, then I still think you may need to rebuild. But you can try re-adding the SharePoint server to the Domain. It may have lost its Domain membership when you removed
AD from it and gone back to being a standalone server.
Paul Stork SharePoint Server MVP
Principal Architect: Blue Chip Consulting Group
Blog: http://dontpapanic.com/blog
Twitter: Follow @pstork
Please remember to mark your question as "answered" if this solves your problem. -
Cannot connect to JDBC data source
We are trying to configure Visual Composer to connect to the backend BI-ABAP
BI database which is DB2, from the Visual Admin on the windows box.
Downloaded the driver for DB2 JDBC from IBM website
(ibm_data_server_driver_package_win64_ALL_LANG_v97.exe) Not sure if this is the correct driver, because we are unable to connect to the BI
Landscape information
BI- ABAP: NW 701 SP4 AIX 6100-3/DB2 v9.5.0.4,FIXPACK 4
BI-JAVA: NW 701 SP4 WIN2003 X64/SQL2005 SP3
When i run this url http://servername:port/TestJDBC_Web/test2 i i get the following error
Exception Details:
com.sap.ip.bi.sdk.exception.BIConnectionFailedException: Cannot open the connection
at com.sap.ip.bi.sdk.dac.connector.jdbc.JdbcConnectionFactory.getConnectionEx(JdbcConnectionFactory.java:238)
at com.sap.ip.bi.sdk.trialarea.connector.servlet.model.JDBCModel.getConnection(JDBCModel.java:796)
at com.sap.ip.bi.sdk.trialarea.connector.servlet.model.JDBCModel.getTables(JDBCModel.java:132)
at com.sap.ip.bi.sdk.trialarea.connector.servlet.controller.Control2.doPost(Control2.java:25)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:760)
at javax.servlet.http.HttpServlet.service(HttpServlet.java:853)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.runServlet(HttpHandlerImpl.java:401)
at com.sap.engine.services.servlets_jsp.server.HttpHandlerImpl.handleRequest(HttpHandlerImpl.java:266)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:386)
at com.sap.engine.services.httpserver.server.RequestAnalizer.startServlet(RequestAnalizer.java:364)
at com.sap.engine.services.httpserver.server.RequestAnalizer.invokeWebContainer(RequestAnalizer.java:1039)
at com.sap.engine.services.httpserver.server.RequestAnalizer.handle(RequestAnalizer.java:265)
at com.sap.engine.services.httpserver.server.Client.handle(Client.java:95)
at com.sap.engine.services.httpserver.server.Processor.request(Processor.java:175)
at com.sap.engine.core.service630.context.cluster.session.ApplicationSessionMessageListener.process(ApplicationSessionMessageListener.java:33)
at com.sap.engine.core.cluster.impl6.session.MessageRunner.run(MessageRunner.java:41)
at com.sap.engine.core.thread.impl3.ActionObject.run(ActionObject.java:37)
at java.security.AccessController.doPrivileged(Native Method)
at com.sap.engine.core.thread.impl3.SingleThread.execute(SingleThread.java:104)
at com.sap.engine.core.thread.impl3.SingleThread.run(SingleThread.java:176)
Caused by: com.sap.ip.bi.sdk.exception.BIResourceException: Cannot open the connection
at com.sap.ip.bi.sdk.dac.connector.jdbc.JdbcManagedConnection.(JdbcManagedConnection.java:123)
at com.sap.ip.bi.sdk.dac.connector.jdbc.JdbcManagedConnectionFactory.createManagedConnection(JdbcManagedConnectionFactory.java:112)
at com.sap.engine.services.connector.jca.ConnectionHashSet.match(ConnectionHashSet.java:338)
at com.sap.engine.services.connector.jca.ConnectionManagerImpl.allocateConnection(ConnectionManagerImpl.java:262)
at com.sap.ip.bi.sdk.dac.connector.jdbc.JdbcConnectionFactory.getConnectionEx(JdbcConnectionFactory.java:233)
... 19 more
Caused by: com.sap.ip.bi.sdk.exception.BIResourceException: Cannot connect to JDBC data source
at com.sap.ip.bi.sdk.dac.connector.jdbc.impl.Connection.connectDB(Connection.java:336)
at com.sap.ip.bi.sdk.dac.connector.jdbc.impl.Connection.connect(Connection.java:99)
at com.sap.ip.bi.sdk.dac.connector.jdbc.JdbcManagedConnection.(JdbcManagedConnection.java:118)
... 23 more
Caused by: java.sql.SQLException: No suitable driver
at java.sql.DriverManager.getConnection(DriverManager.java:532)
at java.sql.DriverManager.getConnection(DriverManager.java:140)
at com.sap.ip.bi.sdk.dac.connector.jdbc.impl.Connection.connectDB(Connection.java:320)
... 25 moreHi,
you can check the configuration:
http://help.sap.com/saphelp_scm50/helpdata/en/43/e35b3315bb2d57e10000000a422035/content.htm
Regards, Mayur -
Unable to open analytics/EM/console(Cannot connect to BI Security Service)
Hi,
After fresh install obiee11.1.1.5.0 1st time i can able to ran presentation services and FMW but after re boot machine i got below kind of error. while checking opmnctl status all serivces are up...
[2012-05-15T01:52:23.000+00:00] [OracleBIServerComponent] [ERROR:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 1790] [13037] Cannot connect to BI Security Service, please make sure this is running properly (with SSL or not) in EM.
[2012-05-15T01:52:23.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 1790] nqsserver: Clustered Oracle BI Server (64-bit) started. Version: 11.1.1.5.0.110427.1127.000.
[2012-05-15T01:52:25.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 161c] [43071] A connection with Cluster Controller W01BGPCBIAPP1A.reg1.uat1bank.dbs.com:9706 was established.
[2012-05-15T02:10:59.000+00:00] [OracleBIServerComponent] [ERROR:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 15cc] [nQSError: 46066] Operation cancelled.
[2012-05-15T02:10:59.000+00:00] [OracleBIServerComponent] [ERROR:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 161c] [nQSError: 46066] Operation cancelled.
[2012-05-15T02:10:59.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 1790] [43031] : Oracle BI Server shutdown.
[2012-05-15T02:10:59.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 1790] [85008] MDX Member Name Cache subsystem statistics - Entries: 0, Sizes: 0 bytes, Overall Queries: 0, Hits: 0(0%), Misses: 0(0%).
[2012-05-15T02:10:59.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 1790] [85007] MDX Member Name Cache subsystem stopped.
[2012-05-15T02:10:59.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 1790] [58001] Query Cache Statistics -- Hits:0(0%), Qualified Misses:0(0%), Unqualified Misses:0(0%).
[2012-05-15T02:10:59.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7dywb3t7Fw00Fzzw0w00000ES000000] [tid: 1790] [14058] Unloaded all subject areas.
[2012-05-15T02:11:23.000+00:00] [OracleBIServerComponent] [WARNING:1] [] [] [ecid: ] [tid: 147c] Warning: Clustering and cache are enabled for this OBIS node, but cluster aware cache is disabled. This can lead to inconsistencies.
[2012-05-15T02:11:32.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: 147c] [36007] Loading repository D:\Oracle\Middleware\instances\instance1\bifoundation\OracleBIServerComponent\coreapplication_obis1\repository\SampleAppLite_BI0001.rpd.
[2012-05-15T02:11:33.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: a74] [14055] Loading subject area: SampleApp Lite ...
[2012-05-15T02:11:34.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: a74] [14056] Finished loading subject area: SampleApp Lite.
[2012-05-15T02:11:34.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: 147c] [58002] Query Cache loaded with 0 entries from saved cache files.
[2012-05-15T02:11:34.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: 147c] [85003] MDX Member Name Cache subsystem started successfully.
[2012-05-15T02:11:34.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: 147c] [85004] MDX Member Name Cache subsystem recovered entries: 0, size: 0 bytes.
[2012-05-15T02:11:35.000+00:00] [OracleBIServerComponent] [ERROR:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: 147c] [13026] Error in getting roles from BI Security Service: 'Error Message From BI Security Service: [nQSError: 12002] Socket communication error at call=Connect: (Number=0) Call=NQRpc: An unknown socket communications error has occurred. [[
[nQSError: 12010] Communication error connecting to remote end point: address = 10.10.10.10; port = 9704.
[nQSError: 46119] Failed to open HTTP connection to server 10.10.10.10 at port 9704.'
[2012-05-15T02:11:36.000+00:00] [OracleBIServerComponent] [ERROR:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: 147c] [13037] Cannot connect to BI Security Service, please make sure this is running properly (with SSL or not) in EM.
[2012-05-15T02:11:36.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: 147c] nqsserver: Clustered Oracle BI Server (64-bit) started. Version: 11.1.1.5.0.110427.1127.000.
[2012-05-15T02:11:36.000+00:00] [OracleBIServerComponent] [NOTIFICATION:1] [] [] [ecid: 00i7e00upPBFw00Fzzw0w00000V^000000] [tid: 190c] [43071] A connection with Cluster Controller W01BGPCBIAPP1A.reg1.uat1bank.dbs.com:9706 was established.
[2012-05-15T02:11:39.000+00:00] [OracleBIServerComponent] [ERROR:1] [] [] [ecid: 00i7e01ZlqXFw00Fzzw0w0000184000003] [tid: 1340] Error Message From BI Security Service: [nQSError: 12002] Socket communication error at call=Connect: (Number=0) Call=NQRpc: An unknown socket communications error has occurred. [[
[nQSError: 12010] Communication error connecting to remote end point: address = ; port = 9704.
[nQSError: 46119] Failed to open HTTP connection to server 10.10.10.10 at port 9704.
*[2012-05-15T02:11:39.000+00:00] [OracleBIServerComponent] [ERROR:1] [] [] [ecid: 00i7e01ZlqXFw00Fzzw0w0000184000003] [tid: 1340] [nQSError: 13037] Cannot connect to BI Security Service, please make sure this is running properly (with SSL or not) in EM.*
*[2012-05-15T02:11:39.000+00:00] [OracleBIServerComponent] [ERROR:1] [] [] [ecid: 00i7e01ZlqXFw00Fzzw0w0000184000003] [tid: 1340] [nQSError: 13037] Cannot connect to BI Security Service, please make sure this is running properly (with SSL or not) in EM.*
Thanks
DevaHi,
While installing Admin Server/Bi_Server i forgot to reset the boot.properties file(encripted password) after re boot i just reset and Restarting the opmn and BI Services its got woking
Thanks
Deva -
[WORKAROUND] Cannot connect to any WiFi network after resume
Hi, I'm having one weird problem that makes my laptop not as mobile as I'd like it to be..
Literally, I have to boot it up again after each move.
Here's the issue: if I suspend to ram, and then resume in a place with different WiFi network, it can't connect to Internet again.
I'm using NetworkManager via corresponding plasmoid in KDE (although, nmcli does not work either).
When I click a network name, I get the following:
"Configuring interface" .... -> Cannot connect to {NetworkName}
(the labels might be a bit different, as I get all notifications in my local language)
Have anyone experienced this before?
Or, AT LEAST, how can I get a bit more verbose output from NetworkManager? Is there a log file?
Here's the hardware:
05:00.0 Network controller: Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)
Here's what I've tried already (and it didn't help):
# systemctl restart NetworkManager
# modprobe -r ath9k
# ncmcli nm sleep false
WORKAROUND FOUND: When I get "Configuring interface" .... -> Cannot connect to {NetworkName} (it happens not only after resumes, btw), I type the following in the console:
sudo dhcpcd -k
So much time passed, so many updates -- still have to do this manually... %)
Last edited by mityukov (2013-12-03 10:19:12)hadrons123 wrote:Try these methods
https://bbs.archlinux.org/viewtopic.php?pid=1241694
Here's what I've tried:
# stop NetworkManager first, just in case if it would not start anything before time
sudo systemctl stop NetworkManager
# kill wpa_supplicant (one of suggestions in the topic)
sudo killall wpa_supplicant
# re-load kernel module with nohwcrypt=1 (another suggestion in the topic):
sudo modprobe -r ath9k
sudo modprobe ath9k nohwcrypt=1
# start NetworkManager again
sudo systemctl start NetworkManager
Then tried to connect the network again: the issue is till the same. Here's the latest dmesg:
$ sudo dmesg -c
[ 3079.006749] ath9k: ath9k: Driver unloaded
[ 3111.623220] cfg80211: Calling CRDA to update world regulatory domain
[ 3111.694588] ath: phy0: ASPM enabled: 0x43
[ 3111.694594] ath: EEPROM regdomain: 0x65
[ 3111.694596] ath: EEPROM indicates we should expect a direct regpair map
[ 3111.694599] ath: Country alpha2 being used: 00
[ 3111.694600] ath: Regpair used: 0x65
[ 3111.697195] ieee80211 phy0: Selected rate control algorithm 'ath9k_rate_control'
[ 3111.697465] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xffffc900140a0000, irq=16
[ 3111.717234] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 3136.958046] r8169 0000:03:00.0 eth0: link down
[ 3136.958159] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 3138.903691] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3138.911517] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3138.911567] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3138.917180] wlan0: authenticated
[ 3138.917697] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3138.917711] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3138.917718] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3138.918897] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3138.932402] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3138.932553] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 3138.932790] wlan0: associated
[ 3139.406632] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3139.415815] cfg80211: Calling CRDA to update world regulatory domain
[ 3143.712977] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3143.720532] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3143.720582] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3143.731367] wlan0: authenticated
[ 3143.731865] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3143.731882] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3143.731888] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3143.735093] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3143.748277] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3143.748533] wlan0: associated
[ 3144.140732] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3144.148708] cfg80211: Calling CRDA to update world regulatory domain
[ 3148.642615] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3148.650085] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3148.650132] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3148.665772] wlan0: authenticated
[ 3148.666264] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3148.666278] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3148.666284] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3148.667980] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3148.681955] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3148.682212] wlan0: associated
[ 3149.016733] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3149.031462] cfg80211: Calling CRDA to update world regulatory domain
[ 3153.648602] wlan0: authenticate with 00:24:8c:65:bb:d5
[ 3153.656323] wlan0: capabilities/regulatory prevented using AP HT/VHT configuration, downgraded
[ 3153.656374] wlan0: send auth to 00:24:8c:65:bb:d5 (try 1/3)
[ 3153.659859] wlan0: authenticated
[ 3153.660389] ath9k 0000:05:00.0 wlan0: disabling HT/VHT due to WEP/TKIP use
[ 3153.660403] ath9k 0000:05:00.0 wlan0: disabling HT as WMM/QoS is not supported by the AP
[ 3153.660410] ath9k 0000:05:00.0 wlan0: disabling VHT as WMM/QoS is not supported by the AP
[ 3153.663889] wlan0: associate with 00:24:8c:65:bb:d5 (try 1/3)
[ 3153.672276] wlan0: RX AssocResp from 00:24:8c:65:bb:d5 (capab=0x411 status=0 aid=3)
[ 3153.672536] wlan0: associated
[ 3153.967817] wlan0: deauthenticating from 00:24:8c:65:bb:d5 by local choice (reason=3)
[ 3153.980619] cfg80211: Calling CRDA to update world regulatory domain -
Hi all.
i am newibe on arch linux.
i read too much but still i cant connect wifi.
it shows wifi networks but when i click them, it says cannoct connect..
my hardware is:
02:00.0 Network controller: Intel Corporation Centrino Wireless-N 130 (rev 34)
03:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
i installed r8168 module and blacklisted 8169 module but not worked. after that i cannot connect weired network too.
Last edited by chataluck (2013-02-11 22:17:20)@ewaller thnx for reply
output:
i am trying to connect agritux
but it is not important. because i cannot connect any essid
it says cannot activated
wlp2s0 Scan completed :
Cell 01 - Address: 18:28:61:1F:5B:1C
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=70/70 Signal level=-32 dBm
Encryption key:on
ESSID:"agritux"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=00000013938b7c16
Extra: Last beacon: 40ms ago
IE: Unknown: 000761677269747578
IE: Unknown: 010882848B962430486C
IE: Unknown: 030106
IE: Unknown: 2A0104
IE: Unknown: 2F0104
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
IE: Unknown: 32040C121860
IE: Unknown: DD09001018020100000000
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : CCMP TKIP
Authentication Suites (1) : PSK
Cell 02 - Address: 18:28:61:36:16:C2
Channel:9
Frequency:2.452 GHz (Channel 9)
Quality=35/70 Signal level=-75 dBm
Encryption key:on
ESSID:"karaca"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 18 Mb/s
24 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 9 Mb/s; 12 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=000000050ca3d59c
Extra: Last beacon: 40ms ago
IE: Unknown: 00066B6172616361
IE: Unknown: 010882848B962430486C
IE: Unknown: 030109
IE: Unknown: 2A0104
IE: Unknown: 2F0104
IE: Unknown: 32040C121860
IE: Unknown: 2D1A6C181BFF00000000000000000000000000000000000000000000
IE: Unknown: 3D1609001300000000000000000000000000000000000000
IE: Unknown: 4A0E14000A002C01C800140005001900
IE: Unknown: 7F0101
IE: Unknown: DD0B001CA85001013616C22B09
IE: Unknown: DDB60050F204104A0001101049001E007FC5100018ACBFBEF29A2C7E5563E04772F25589FC30303030303030311044000102103B00010310470010D3EC1E9588B451FD9E0849E4521F4AB5102100194169725469657320576972656C657373204E6574776F726B731023000941697235333431545410240008312E302E302E31311042000F4154313036313135323030353536351054000800060050F204000110110009416972353334315454100800020084103C000103
IE: Unknown: DD090010180201F0040000
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (1) : TKIP
Authentication Suites (1) : PSK
IE: Unknown: DD180050F2020101800003A4000027A4000042435E0062322F00
Cell 03 - Address: C8:6C:87:8B:8D:DC
Channel:6
Frequency:2.437 GHz (Channel 6)
Quality=36/70 Signal level=-74 dBm
Encryption key:on
ESSID:"ZyXEL3596oT1"
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s; 9 Mb/s
18 Mb/s; 36 Mb/s; 54 Mb/s
Bit Rates:6 Mb/s; 12 Mb/s; 24 Mb/s; 48 Mb/s
Mode:Master
Extra:tsf=0000007d6596f9c0
Extra: Last beacon: 40ms ago
IE: Unknown: 000C5A7958454C333539366F5431
IE: Unknown: 010882848B961224486C
IE: Unknown: 030106
IE: Unknown: 2A0104
IE: Unknown: 32040C183060
IE: Unknown: 2D1A6E1117FF000000010000000000000000000000000C0000000000
IE: Unknown: 3D1606070400000000000000000000000000000000000000
IE: Unknown: 3E0100
IE: WPA Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : TKIP CCMP
Authentication Suites (1) : PSK
IE: IEEE 802.11i/WPA2 Version 1
Group Cipher : TKIP
Pairwise Ciphers (2) : TKIP CCMP
Authentication Suites (1) : PSK
IE: Unknown: DD180050F2020101000003A4000027A4000042435E0062322F00
IE: Unknown: 0B050000237A12
IE: Unknown: 7F0101
IE: Unknown: DD07000C4304000000
IE: Unknown: 0706414C20010D10
IE: Unknown: DD1E00904C336E1117FF000000010000000000000000000000000C0000000000
IE: Unknown: DD1A00904C3406070400000000000000000000000000000000000000
IE: Unknown: DD9F0050F204104A0001101044000102103B00010310470010BC329E001DD811B28601C86C878B8DDC1021001852616C696E6B20546563686E6F6C6F67792C20436F72702E1023001C52616C696E6B20576972656C6573732041636365737320506F696E74102400065254323836301042000831323334353637381054000800060050F20400011011000B5472656E64436869704150100800020084103C000100
lo Interface doesn't support scanning.
enp3s0 Interface doesn't support scanning.
Last edited by chataluck (2013-02-09 19:15:40) -
app store on itunes not working error iTune cannot connect to itune store unknown error the network conection is refused on windows 8
Microsoft Windows 8 Business Edition (Build 9200)
Hewlett-Packard HP Pavilion dv6 Notebook PC
iTunes 11.1.5.5
QuickTime not available
FairPlay 2.5.16
Apple Application Support 3.0.1
iPod Updater Library 11.1f5
CD Driver 2.2.3.0
CD Driver DLL 2.1.3.1
Apple Mobile Device 7.1.1.3
Apple Mobile Device Driver 1.64.0.0
Bonjour 3.0.0.10 (333.10)
Gracenote SDK 1.9.6.502
Gracenote MusicID 1.9.6.115
Gracenote Submit 1.9.6.143
Gracenote DSP 1.9.6.45
iTunes Serial Number 0150B8980AD913B8
Current user is not an administrator.
The current local date and time is 2014-03-18 04:37:01.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is supported.
Core Media is supported.
**** External Plug-ins Information ****
No external plug-ins installed.
iPodService 11.1.5.5 is currently running.
iTunesHelper is currently not running.
Apple Mobile Device service 3.3.0.0 is currently running.
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name: {240FD97D-8118-4928-BF4E-8A531F89D837}
Description: Microsoft Wi-Fi Direct Virtual Adapter
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 16:00:00 1969
Lease Expires: Wed Dec 31 16:00:00 1969
DNS Servers:
Adapter Name: {BCD0EF3F-C4A4-402C-969A-C46C079E56A6}
Description: Bluetooth Device (Personal Area Network)
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 16:00:00 1969
Lease Expires: Wed Dec 31 16:00:00 1969
DNS Servers:
Adapter Name: {DD5C0797-BC23-4732-85FE-AC59C926EE98}
Description: Realtek PCIe GBE Family Controller
IP Address: 10.144.120.70
Subnet Mask: 255.255.255.0
Default Gateway: 10.144.120.1
DHCP Enabled: Yes
DHCP Server: 10.144.120.3
Lease Obtained: Tue Mar 18 03:26:26 2014
Lease Expires: Mon Jun 16 03:26:26 2014
DNS Servers: 10.144.5.30
10.144.130.5
Adapter Name: {E7CA4853-FF4A-49AE-AA4E-06BB1DEE67D4}
Description: Ralink RT5390 802.11b/g/n WiFi Adapter
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 16:00:00 1969
Lease Expires: Wed Dec 31 16:00:00 1969
DNS Servers:
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
Firewall Information
Windows Firewall is on.
iTunes is NOT enabled in Windows Firewall.
Connection attempt to Apple web site was unsuccessful.
The network connection timed out.
Basic connection to the store failed.
The network connection was refused.
Connection attempt to Gracenote server was successful.
The network connection was refused.
iTunes has never successfully accessed the iTunes Store.
**** CD/DVD Drive Tests ****
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.3.0),
F: hp DVD-RAM UJ8B1, Rev H.02
Drive is empty. -
Cannot connect Access Point (WPA2 EAP Leap)
Dear Expert
We 've try to configure Client to connect to Access Point (WPA2 EAP Leap) but cannot connect and We've found LOG on Wireless Controller as below.
Please advise me that What I should to do.
*Sep 29 14:45:43.102: %APF-1-DISCONECT_MOBILE_DUE_TO_WLAN_SW: apf_policy.c:535 Disconnecting mobile 00:14:a5:d2:81:25 due to switch of WLANs from 2 to 3
*Sep 29 14:45:41.085: %APF-1-PROC_RSN_WARP_IE_FAILED: apf_80211.c:2234 Could not process the RSN and WARP IEs. station not using WPA or WPA2 on WLAN requiring WPA and/or WPA2.MobileStation: 00:14:a5:d2:81:25, SSID:airport-sup,AP: 00:26:cb:a9:7d:30.
Best Regards
PeeraHi Peera,
the first message is because the user switched quickly between SSIDs. This is a behavior that WLC blocks by default.
Change the option "Fast SSID change" to enabled if you want to stop that blocking.
The second message simply means that the client was not configured for wpa/wpa2 ... This is something I can hardly comment on since I can't see the client configuration
Maybe you are looking for
-
Opening CS3 file in CS4 - fonts wrong!
I have an FLA created in CS3 (Mac). It includes a couple of fonts that were made into symbols. I'm both using those symbols to set the font for dynamic text boxes on stage in various symbols (by selecting the font-name-with-asterisk from the font men
-
Post got moved again :( (HH5 - update/fix has been...
I cannot reply to the posts I am making as they keep being added to a locked post Can the post be unlocked so I don't have to keep starting a new one each time? I have lots of these in the TR069 event log, but all before the update, and non after.
-
Data Type Enhancements: ECC - SRM Scenario
Hello, Can anyone tell us how to use the Data Type Enhancement. and what all Software component dependencies we need to define for that. This is with Context for ECC-SRM Integration -- we have installed the add on component LOCINSUS -- this is requir
-
How do I validate a regex before running it?
I wish to make sure that my regex is valid before running it. Is there boolean method to validate it?
-
{Edited per forum guidelines} Need assistance NOW
Best Buy I am appalled by the lack of empowerment your associates are given. After an hour of being told "no" by your in-store associates about a replacement phone which was approved for junk out replacement, I now have to deal with the product being