1G Ohm multimeter reading with only 1k ohm resistence

I am a student just starting to use Mulitisim student edition 12.0 for very basic circuits. My PC opetating system is windows XP.
First assignment went perfectly with a variety of series circuits using basic components - DC voltage source, resistors, ground, multimeter.
Started on my second set of assignments with parallel circuits yesterday. Same very basic components.
Two problems - first was a "no nodes" in circuit error when trying to run the simulation. Surprising because as far as I know my steps to construction the circuit were the same as the previous assignment (just resistors in parallel rather than series). This error went away after I relocated the voltage source.
Next problem, which continues, - simulation results on multimeter show correct voltage 12V but 1G ohm and Amperage " r" out of the range. I have checked the instrument setting and they seem ok. No open point in the circuit detected or that I can see.
The only other piece of information I can think of that might help troubleshooting this is that my PC does show 100% CPU (2G, 2.1GHz) use quite often when running multisim.
Solved!
Go to Solution.

Thanks for replying, Tom. You get credit for solving this one.
When I went back to my circuit and looked at it after a couple days I spotted the problems.
First, was a branch with no resistance that I believe caused the "no nodes". I put it back in green wire on
the attached circuit. Second, was not removing the power supply when checking the resistance.
Kind of embarrasing errors even for a beginner.
Anyway, you prompted me to take go back to the file and discover the problem which I appreciate.
In the future I will set the problem aside for a while if I have that option and then,
make sure to attach the circuit if I post it looking for help.
Bill H
Attachments:
Experiment 5-2.5v2.ms12 ‏92 KB

Similar Messages

When I try open a .pdf file my Adobe Reader 11 only allows the download / save opening the related window and don't show me both options 1) open with ... and 2) save as.... probably someone flagged the choise... always perform this way ....

When I try open a .pdf file my Adobe Reader 11 only allows the download / save opening the related window and don't show me both options 1) open with ... and 2) save as.... probably someone flagged the choise... always perform this way ....
Could some one give help and let me know where I can probably find the settings option that allows me to change and switch to previous situation where it was possible to decide time to time how to proceed either opening the file or saving it ??
Thanks in advance
David

What is your operating system?
Open a PDF from where? If online, in what browser?

How can i create a new user with only read rights ?

How can i create a new user with only read rights ?

You are asking about a Database User I hope.
You can look into the Oracle 8i Documentation and find various privillages listed.
In particular, you may find:
Chapter 27 Privileges, Roles, and Security Policies
an intresting chapter.
You may want to do this with the various tools included with 8i - including the
Oracle DBA Studio - expand the Security node and you can create USERS and ROLES.
Or use SQL*Plus. To create a
user / password named John / Smith, you would login to SQL*Plus as System/manager (or other) and type in:
Create user John identified by Smith;
Grant CONNECT to John;
Grant SELECT ANY TABLE to John;
commit;
There is much more you can do
depending on your needs.
Please read the documentation.
-John
null

How to create a PDF with Only Read Property

Hello Gurus,
I have a big question:
How can I create an Smartform which can be exported in an Only Read PDF ?
I need to do that for creating a PDF file which information can not be copied.
Is that Possible?
Thanks!!!
rgds.
Miguel Angel.

Hi,
the nature of a PDF file is that it cannot be modified, only read with Adobe Reader, and not only once downloading the form from SAP but with any tool. What you pretend is impossible, because there are many tools in the market for making the PDF files either editable or per Copy + paste you can process the texts in Word or any software.
Search in the internet (www.download.com) if there´s a software that can lock your file, but I am sure that this will not work in conjunction with SAP during generation of file; it´s going to be a manual work.

Photoshop-When opening image without tab view, image opens with only a portion in view

I having an issue with CC.
When electing in the preferences to not open image in Tabs. The images open with only about 25% of the image area showing. Forcing me to (command) 0 for full to screen preview or (command) +/- to see the image.
I am not talking about seeing the image at 100% resolution just the entire image within the floating window without having to command before view.
Sidenote: Adobe Customer Service is all based in India. I spent 4 hours on the phone only to hear that this is that way photoshop works.
There would be no logical explanation for this. Since the first version of Photoshop this has not been the case.
I think this should be called view porn with wife in the room mode. Other than that I see no point.
Can anyone help?
Lv
Chadwick Tyler

Moving discussion to Photoshop forum.

____FAST CASH WITH ONLY 50$ (CLICK HERE) !!!!

AMAZING PLAN TO BECOME RICH IN DAYS
AMAZING PLAN TO BECOME RICH!! HOW TO BECOME
RICH HOW TO TURN 50 DOLLARS INTO MILLIONS
OF DOLLARS:
READING THIS COULD CHANGE YOUR LIFE! IT DOES
WORK!
I found this on a bulletin board and decided
to try it. A little while back, I was
browsing through newsgroups,
just like you are now, and came across an
article similar to this that said you could make hundreds of thousands
of dollars within weeks (which would soon
turn into millions) with only an initial
investment of $50.00! So I thought,
"Yeah right, this must be a scam", but like
most of us, I was curious, so I kept
reading. Anyway, it said that you
send $10.00 to each of the 5 names and
address stated in the article. You then
place your own name and address in the
bottom of the list at #5, and post the
article in at least 250 newsgroups. (There
are thousands) No catch, that was it.
So after thinking it over, and talking to a
few people first, I thought about trying it.
I figured: "what have I got
to lose except 5 stamps and $50.00, right?"
Then I invested the measly $50.00 (I use the
word "measly" because $50 really
is measly compared to the money I have made
through the initial investment). Well GUESS
WHAT!?... within 7 days,
I started getting money in the mail! I was
shocked! I figured it would end soon, but
the money just kept coming in.
In my first week, I made about $50.00. By
the end of the second week I had made a
total of over $1,000! In the third
week I had over $10,000 and it's still
growing. This is now my fourth week and I
have made a total of just over
$42,000 and it's still coming in rapidly.
It's certainly worth $50.00, and 5 stamps, I
have spent more than that on
the lottery!! Let me tell you how this works
and most importantly, WHY it works... Also,
make sure you print a copy
of this article NOW, so you can get the
information off of it as you need it. I
promise you that if you follow the
directions exactly, that you will start
making more money than you thought possible
by doing something so easy!
Suggestion: Read this entire message
carefully! (print it out or download it.)
Follow the simple directions and
watch the money come in! It's easy. It's legal. And, your investment is only $50.00
(Plus postage)
IMPORTANT: This is not a rip-off; it is not
indecent; it is not illegal; and it is 99%
no risk - it really works!
If all of the following instructions are
adhered to, you will receive extraordinary
dividends.
NOTE: Please follow these directions
EXACTLY, and $50,000 or more can be yours in
20 to 60 days.
This program remains successful because of
the honesty and integrity of the
participants.
Please continue its success by carefully
adhering to the instructions. You will now become part of the Mail
Order business. In this business your
product is not solid and tangible, it's a
service.
You are in the business of developing
Mailing Lists. Many large corporations are
happy to pay big bucks for
quality lists. However, the money made from
the mailing lists is secondary to the income which is made from
people like you and me asking to be included
in that list. Here are the 4 easy steps to success:
STEP 1:
Get 5 separate pieces of paper and
write the following on each piece of paper
"PLEASE PUT ME ON YOUR MAILING LIST." Once
added to the list, each person will send you
a new component
and/or moneymaking advice to help you along
the way. This advice has been passed down
person to person and
is very helpful. Now get 50 US $10.00 bills
(or a combination of bills totaling $10) and
place ONE inside EACH of the 5 pieces of paper so the bill will
not be seen through the envelope (to prevent
thievery).
Next, place one paper in each of the 5
envelopes and seal them. You should now have
5 sealed envelopes,
each with a piece of paper stating the above
phrase, your name and address,and $10.00
bill.
What you are doing is creating a service.
THIS IS ABSOLUTELY LEGAL! You are requesting
a legitimate service
and you are paying for it! Like most of us I
was a little skeptical and a little worried
about the legal aspects
of it all. So I checked it out with the U.S.
Post Office (1-800-725-2161) and they
confirmed that it is indeed legal.
Mail the 5 envelopes to the following
addresses:
1. Eng. Yousef Abu Hadhoud P.O. Box 4028
North Hashemi, Amman - Jordan
2. Steve Wehvila3155 Vernon St.Duluth, MN
55806
3. James
Rush621QueenAvenueMinneapolis,MN55411
4. Liz Grice 3413 Harvard ave. Columbia, SC
29205
5. Jassim Ahmed Qassim Marhoon, BLK 643
Rd 4313 HSE 727, Nuwaidrat - Bahrain
STEP 2:
Now take the #1 name off the list
that you see above, move the other names up
(5 becomes 4, 4 becomes 3, etc...) and add
YOUR Name as number 5 on the list.
STEP 3:
Change anything you need to, but try
to keep this article as close to original as
possible.
Now, post your amended article to at least
250 newsgroups. (I think there are close to
24,000 groups)
All you need is 250, but remember, the more
you post, the more money you make! You won't
get very much
unless you post like crazy. :)This is
perfectly legal! If you have any doubts,
refer to Title 18 Sec. 1302 & 1341 of the
Postal lottery laws. Keep a copy of these
steps for yourself and,
whenever you need money, you can use it again, and again. PLEASE REMEMBER that this
program remains successful because of the honesty and integrity of the
participants and by their carefully adhering
to the directions.
Look at it this way. If you are of
integrity, the program will continue and the
money that so many others have
received will come your way. NOTE: You may
want to retain every name and address sent to you, either on a
computer or hard copy and keep the notes
people send you. This VERIFIES that you are
truly providing a service.
(Also, it might be a good idea to wrap the
cash in dark paper to reduce the risk of
mail theft.)
So, as each post is downloaded and the
directions carefully followed, six members
will be reimbursed for
their participation as a List Developer with
one dollar each. Your name will move up the
list geometrically so
that when your name reaches the #1 position
you will be receiving hundreds of thousands
of dollars in CASH!!!
What an opportunity for only $50.00 ($10.00
for each of the first six people listed
above) Send it now,
add your own name to the list and you're in business!
DIRECTIONS ----- FOR HOW TO POST TO
NEWSGROUPS--------
Step 1:
You do not need to re-type this
entire letter to do your own posting, Simply
put your cursor at the
beginning of this letter and drag your
cursor to the bottom of this document (so
that the document is "highlighted"),
and select 'copy' from the edit menu. This
will copy the entire letter into the
computer's memory.
Step 2:
Open a blank 'notepad' file (such as
in Microsoft Word) and place your cursor at
the top of the blank page.
From the 'edit' menu select 'paste'. This
will paste a copy of the letter into notepad
so that you can add your name
to the list.
Step 3:
Save your new notepad file as a .txt
file. If you want to do your postings in
different settings,
you'll always have this file to go back to.
Step 4:
Use Netscape or Internet explorer
and try searching for various newsgroups (on-
line forums, message boards,
chat sites, discussions.)
Step 5:
Visit these message boards and post
this article as a new message by highlighting the text of this
letter and selecting paste from the edit
menu. Fill in the Subject, this will be the
header that everyone sees as
they scroll through the list of postings in
a particular group, click the post message
button. You're done with your first one!
Congratulations...
THAT'S IT!
All you have to
do is jump to different newsgroups and post
away,
after you get the hang of it, it will take about 30 seconds for each newsgroup!
**REMEMBER, THE MORE NEWSGROUPS YOU POST IN,
THE MORE MONEY YOU WILL MAKE! BUT YOU HAVE
TO POST A MINIMUM OF 250**
That's it! You will begin receiving money
from around the world within days! You may
eventually want to rent a
P.O.Box due to the large amount of mail you
will receive. If you wish to stay anonymous,
you can invent a name
to use, as long as the postman will deliver
it.
**JUST MAKE SURE ALL THE ADDRESSES ARE
CORRECT.**
Now the WHY part:
Out of 250 postings, say I receive only 5
replies (a very low example). So then I made
$50.00 with my name at #5
on the letter. Now, each of the 5 persons
who just sent me $10.00 make the MINIMUM 250 postings, each with my name
at #5 and only 5 persons respond to each of
the original 5, that is another $250.00 for
me, now those 25 each make
250 MINIMUM posts with my name at #4 and
only 5 replies each, I will bring in an additional $1250!
Now, those 125 persons turn around and post
the MINIMUM 250 with my name at #3 and only
receive 5 replies each,
I will make an additional $6260! OK, now here
is the fun part, each of those 625 persons
post a MINIMUM 250 letters
with my name at #2 and they each only
receive 5 replies, that just made me
$31,2500!!!
Those 3,125 persons will all deliver this message to 250 newsgroups with my name at #1
and if still
5 persons per 200 newsgroups react I will
receive $156,250! With an original investment
of only $50.00!
AMAZING! When your name is no longer on the
list, you just take the latest posting in
the newsgroups,
and send out another $50.00 to names on the list, putting your name at number 5 again.
And start posting again. The thing to remember is: do you realize that thousands
upon thousands of people
all over the world are joining the internet
and reading these articles everyday?, JUST LIKE YOU are now!!
So, can you afford $50.00 and see if it
really works?? I think so... People have
said, "what if the plan is played
out and no one sends you the money? So what!
What are the chances of that happening when
there are tons of
new honest users and new honest people who
are joining the internet and newsgroups
everyday and are willing
to give it a try? Estimates are at 20,000 to
50,000 new users, every day, with thousands
of those joining the actual internet. Remember, play FAIRLY and
HONESTLY and this will really work.
NOTE: This program can and will work for you
s long as you post the message in at least
250 newsgroups
(e.g. message boards). This might take a long time, probably several hours. But
remember, as far fetched and
ridiculous as it seems, if you follow all
the instructions of this system, you will
become rich within an
extremely short period of time. Believe me,
IT'S WORTH IT!!! I just urge you to be fair
and honest.
As long as each person (including you!) sends $10 to everyone on the list, everybody
(also including you!)
will become extremely wealthy within just a
couple of months, and will start receiving money within the first
week or two! Legal Note: This system is
perfectly legal. It is not a lottery or a
scheme intending to defraud,
it is rather a business. It is part of the
mail order business. By receiving money from
others, you do not offer
them a lottery or any prize based on chance;
you simply offer them a service (i.e.
placing them on your mailing list),
which they request in their letter. By
definition, this is a service: a consumer
desires something
(being put on your mailing list) and is
willing to pay for it, and you fulfill their
desire by performing
the service of putting their name on your
mailing list for a set fee. By sending money
to others and writing
"please place me on your mailing list", you
do not ask to be entered into a lottery or
win a prize based on
chance, you are asking for a service.
Therefore, this system is perfectly legal.

Tobias
I am not sure what piece of documentation you were looking at where you saw a figure of 50 concurrent users or what it meant to covey about capacity. I can believe that this hardware may not scale above 50 concurrent VPN users, but I have great difficulty in believe that 50 LAN users will stress this machine (or 150). I am not clear when you say 2x10mbit whether that is one LAN interface for users and one LAN for outside connection. But I feel pretty comfortable that an 1812 can handle traffic for 150 LAN connected users.
HTH
Rick

Setting up an airport express router with only an ipad

i will be in a hotel room with only ethernet wired connection. i am traveling only with my ipad. can i hook up an wireless modem (Airport exrpress) without a laptop? How?

The iPad operating system will not support AirPort Utility, the application that is needed to configure the AirPort Express.
Your best bet for the time being is going to be to try to use the AirPort Express in its default settings.
Connect the Express to the Ethernet port at the hotel and power it up. The Express is broadcasting a default wireless network with a name like Apple Network xxxxxx, where the "x" could be a letter or number. Look for that wireless network to log on (there is no password). Then open your browser to see if the hotel's log in page appears so you can agree to terms and fees, etc.
If the hotel does not use a log in page, you should be connected to the Internet if all is well. Since you have an "open" network, anyone within range can log on to your wireless, so you might want to be careful with any sensitive banking or credit card transactions.
It's not likely that a hacker is close by, but you never know.
Once you get back home, you can use AirPort Utility to setup the Express to name your wireless network and etstablish a password. Once you save the settings, you should not need to configure the Experss again as it will retain its settings.

I have OS 10.8.2 and use wireless at home just fine. When I visit a friend with only a cable modem internet my Mac Book Pro will not connect. What do I need to do?

I have OS 10.8.2 and use wireless at home just fine.
When I visit a friend with only a cable modem internet my Mac Book Pro will not connect.
I see that the Mac Book Pro is picking up the internet when I check the internet preference section but it will not open Safari.
What do I need to do connect via a cable modem?

You need to power off the modem for 15-30 seconds, then power back up and then connect. The modem is remembering the last connection (your friend).

I have an older HDTV with only 1 HDMI connection. I use a Bose 3.2.1. GS Series II system and have a HDTV cable box. Bose system has no HDMI. How can I connect an Apple TV to this system?

I have an older flat panel HDTV with only 1 HDMI connection which is being used through my cable box for TV reception. I also use a Bose 3.2.1. GS Series II home theatre system. It has no HDMI inputs. Can I use an Apple TV with my present system? I'd prefer not hearing, "buy a new flat panel."
Cliff

Have you tried adjusting the "Audio Out" and the "Dolby Digital" settings in settings > audio and video? It may be worth trying several combinations of these settings, although typically it is the "Dolby Digital" setting that causes most problems for users.

How do i set up the time capsule with only a wireless net work? it keeps asking me to plug in a cable and i do not have one.

how do i set up the time capsule with only a wireless net work? it keeps asking me to plug in a cable and i do not have one.

Are you using a v6 uitlity.. because it is a toy.. ??
Get v5 utility and then you can hold down the option key and select the right mode.
If you have lion, just install it.. For ML follow this.
How to load 5.6 into ML.
1. Download 5.6 for Lion.
http://support.apple.com/kb/DL1482
Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
2. Download and install unpkg.
http://www.timdoug.com/unpkg/
Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
You cannot uninstall 6.1 so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.

Can I run adobe master collection in a windows partition on a basic mbp 13" with only the intel chipset?

can I run adobe master collection in a windows partition on a basic mbp 13" with only the intel chipset?
I want to install 16 gb ram but I don't think I can change the lack of video card. I wanted this basic machine because it has fairly long battery life. I don't need or want retina at this time. My model is the mid 2012 model. I am running the adobe collection for mac, I want to run the windows versions. Is it possible? What is the most ram I could access using something like fusion 5, assuming I could get fusion 5 to work? would it refuse to run because of the intel chipset and lack of video card?
If I'm wrong and there is a way to add a video card to this model, could some version of fusion and windows 7 access more than 2 gb operating ram?
What cost would I be incurring, and would it be cheaper to buy a windows laptop with more ram than I could access via a virtual machine?
I want to work on a client's work in the windows versions of the creative suite, with occasional usage of after effects for windows, and to use some web plug-ins only available in windows versions, and to try some windows-only video and audio software.
thanks for any suggestions. While many people have told me I can run everything on my macbook, I am concerned about what I think is a limited amount of ram that can be accessed over the virtual machine partition softwares, and I don't know if what I want to attempt is actually possible.
My mbp os is 10.8.2 on a 2.5 GHz intel core i5 4 gb 1600MHz DDR3 with 500 hard drive. the basic 13" mid 2012 machine.
I'm hoping to install 16 G of opertating ram to allow more adobe programs to run concurrently- just when I am working on the mac side.
also, off track but, for years I have wanted a small machine that is more easily portable than my 15" machines. I have only had this used machine for a few weeks, but already I have been very satisfied and used it for presentations at clients. I don't want an air because I really want the dvd burner and player. No matter what apple says about wireless, there are decades of legacy work stored on optical discs all over the world, and I don't want to be unable to open something at a client's office because I don't have a dvd drive. Additionally, I have very large files I want to transfer via ethernet or firewire so that the transfer will take less time and be more secure than wifi. I resist apple's trend to make every machine a disposable toy that is viable only a year or so. I have read reviews that label the mbp it a poor value compared to the air. If all you need to do is text and communicate via wifi, many devices will sufice, and an air is certainly the most elegant. But what about the cost of large ssd's and protecting the drive against damage from shock? I want to be able to move this thing around and the small size is much safer inside my padded bag when I sit in narrow airplane seats, crowded trains and other congested spaces. I am much more likely to be able to borrow a large screen in a client's office ( with the use of one of the three adapters I had to buy) than to be able to borrow a dvd drive that has drivers for mac os 10.8.2. I suspect this may be the last generation of machines that have optical drives and ethernet, and that was why I purchased it so that I could continue to do work into the next few years. I am impressed by the retina display, but I need long battery life. And as beautiful as the retina display is, it is even more of a problem when trying to cross platform with the windows world. I wish I could infuence apple to do a trial product flow for a machine designed to work with 80% of the business world that uses windows. How spectacular that would be. With all their expertise and adept hardware design, to create a machine that cross platforms better than a windows machine itself works? Now that would be an accomplishment. Instead of 8 or 9 percent of the total computer sales, why not aim for a higher percentage? Smart devices will keep moving toward portable computers in power, anyway.

confused, bothered and bewildered wrote:
can I run adobe master collection in a windows partition on a basic mbp 13" with only the intel chipset?
I want to install 16 gb ram but I don't think I can change the lack of video card. I wanted this basic machine because it has fairly long battery life. I don't need or want retina at this time. My model is the mid 2012 model. I am running the adobe collection for mac, I want to run the windows versions. Is it possible? What is the most ram I could access using something like fusion 5, assuming I could get fusion 5 to work? would it refuse to run because of the intel chipset and lack of video card?
If I'm wrong and there is a way to add a video card to this model, could some version of fusion and windows 7 access more than 2 gb operating ram?
What cost would I be incurring, and would it be cheaper to buy a windows laptop with more ram than I could access via a virtual machine?...
Fusion should work on your machine and if you put 16 GB of RAM in (see http://eshop.macsales.com/shop/memory/Apple_MacBook_MacBook_Pro/Upgrade/DDR3_160 0MHz_SDRAM), Fusion can access a good portion of that. Also, in a Virtual Machine, the guest OS is presented with Fusion's video card emulation, not what's in hardware on your Mac. Of course, finding Windows 7 now that Win 8 has been released could take some doing and the Win 8 Pro upgrade price is supposed to jump to $200 the end of the month. Add that to the price of Fusion and the extra RAM and you're beginning to get into the realm of low end real PC's.
As to cross platform, I assume you're aware of BootCamp (http://support.apple.com/kb/HT1461).

How to connect many devices with only one FW800 port in iMac?

Hi,
I am upgrading to a new Intel iMac from a 2004 vintage Dual2.0GHz PowerMac. I currently have 8x d2 Quadra drives chained by FW800, and 2x Iomega drives connected vis FW400 hub which also connects HD cams.
My questions is that with only one FW800 port in iMac, I think my devices connectivity is the following?
(1) Get a FW 800 hub (I can only find 2 port ones at the Apple store and BestBuy)
(2) Connect the d2 Quadras to one port of the FW800 hub
(3) Get a FW 800 to FW 400 cable
(4) Connect my 6 port FW400 hub to the 2nd port of the FW800 hub
Thanks for reviewing this solution, and I would also appreciate other suggestions or hear about your experiences if you have a similar set-up.
Will

In addition to your listed considerations, you should consider the following.
Many storage needs do not required FireWire 800 speed. For example, USB 2.0 works fine for your Time Machine backup drive. If you are just storing user data such as your iPhoto or iTunes media files, USB 2.0 is more than fast enough. So, as much as possible, if any of those external drives have USB 2.0 connections and the data storage does not need FireWire 800 speed, offload as much as possible to USB 2.0. I used to be a +FireWire snob+, but since getting an Intel iMac, I find that USB 2.0 works quite well for most data storage purposes.
There are new hard drives that are power efficient and as large as 2TB. Consolidate your data storage needs onto a smaller number of very large drives, partitioned as needed. This will make your setup more reliable (smaller number drives), and save reduce power consumption. If any of your current externals are SATA, you can probably replace the existing drive with an extra large one.
So, I think you setup should be, extra large FireWire 800 drive connected to the FireWire 800 port directly. Using a 9-pin to 6-pin cable, connect the FireWire 400 hub. Connect any non-storage FireWire 400 devices there. Do some data transfer testing to make sure having the 400 hub there on the chain does not cause the 800 connection to slow down.
Connect other drives as needed using USB 2.0, existing or new. Retire the smaller of your external drives.

I have two apple ID's, one with all my apps and one with only Mavericks. Will Mavericks update automatically if i'm not logged in to the apple ID I used to download it?

I have two apple ID's, one with all my apps and one with only Mavericks. Will Mavericks update automatically if i'm not logged in to the apple ID I used to download it?

Some things are mixed up here, seemingly...
I seem to have two Apple ID's attached to my e-mail.
An Apple ID is a valid email address, apparently. How can those be "attached to your email"... what email?
Facetime will not verify my e-mail address because it is associated with the other account.
This doesn't make sense. You can register multiple, even non-Apple-ID, email addresses and their aliases with FaceTime.
So, maybe you can explain your problem better - what you want and the steps you've taken and what you have so far. If something doesn't work, please tell the exact error message, too.

An iPhone can be synced with only one iTunes library at a time

I recently bought a MacBook Pro, and I figured it would be pretty simple to move my iPhone to sync with iTunes on the Mac from iTunes on my pc, afterall it is the same program and both are designed for the iPhone.
I have been successful in getting the Contacts and Calendar to sync, but the Music, Applications, Video and a few other things give me this message when I check the sync box:
"The iPhone is synced with another iTunes library. Do you want to erase the iPhone and sync with this iTunes library? An iPhone can be synced with only one iTunes library at a time. Erasing and syncing replaces the contents of this iPhone with the contents of this iTunes library."
Obviously, I don't want to erase everything. Actually, I don't care about Music, Videos, Podcasts or Ringtones as I don't have any, but I do care about Photos and Applications. Actually Photos I can reload too, but I don't want to loose the apps I have purchased with the iTunes App Store.
I even tried going back to the PC and unchecking the Sync boxes on it, hoping this might disassociate it from the phone, but now even on that PC I get the same message.
How do I disconnect phone from the old iTunes and be able to sync it to the new iTunes? This should be simple right?

I made an appointment with a Mac Genius and I will say that while it was better than getting to talk to India on a poor quality phone call it was just about as helpful. Sure she was cute and friendly, but I left without my issue resolved and was surprised that I didn't even get a followup from anyone asking about my experience (hence my venting here)
Anyway, I found a solution for my issue here: http://tinyfish.net/2008/07/18/how-to-sync-iphone-with-multiple-computers/
This is a real solution to the issue, and has the benefit that I can do this to as many machines as I need and sync at any of them instead of just one. Hopefully, Apple doesn't delete my response since it truly is the answer to the problem and others might be looking for the same solution.

Can i import the video from a camrecorder with only a USB connection?

Hi, I am very new and may i ask some silly questions? I was using an very old DV camcorder with a firewire connection and it worked fine with my Mac, but now I want to buy a new camcorder and i found that the models I like do not have the firewire links, only they have the USB, the models with the firewire links are very old styles.... can anyone tell me what to do with only the USB link? thanks!

Panasonic HD camcorder, HDC-SD1
Advanced High Definition (AVCHD) isn't supported by Apple you will encounter editing limitations wait for the apple software to catch up with this format.
Panasonic SDR-H250
Panasonic's hard disk model, 3CCD, MPEG2
the only thing this cam has going for it is the 3CCD, converting the already compressed mpeg2 video to the DV format for iMovie will result in an additional lost in quality an will be time comsuming (not to mention the extra app(s) neede for the conversion.
) you'll need for the conversion .
Here's what I'd do. I'd purchase a solid mini DV cam with all the bells and whistles and wait for the dusk to clear on the all new/problematic formats. In the process saving $400 - $500.
Don't become all hyped up with the marketing crap for these new cams. Sony Vegas 7 is the only app I know of that just recently updated to handle the AVCHD format. And until comsumers start burning HD DVDs whats the point. A good mini DV cam will still be viable a couple of years down the road and todays new cams will be cheaper and better.
Here's a sweet cam that will allow you to take videos and edit them in no time.
Sony DCR-HC96,
Analog-to-Digital Converter, external Microphone Input
Analog Audio/Video Input(s) just to mention a few of the most sought after features.
You can find this cam on the web (eg. amazon.com) for about $500.
Then again that's just what I'd do, other my have different advice/suggestions.
Hope this info is of some use.

1G Ohm multimeter reading with only 1k ohm resistence

Similar Messages

Maybe you are looking for