2821 Router with wic-1ADSL card

I am trying to verify a code that will recognize a WIC-1ADSL card in a 2821. The Cisco Software tool page shows that 12.4.10 IPVOICE code has support for this but the card is not seen on the router. When I try the enterprise version 12.4.9(T1) It does't see that card either but shows a VPN module??
Does anyone know what release will work? I am replacing 2620 routers (12.3.19) that have these cards in them for Disaster Recovery. I need support for ADSL- Asymetric Digital Subscriber Line support.

Important bits below:
boot-start-marker
boot system flash flash:c2800nm-advipservicesk9-mz.124-3b.bin
boot-end-marker
policy-map Child
class class-default
fair-queue
random-detect dscp-based
interface ATM0/0/0
description ADSL Service
bandwidth 399
no ip address
load-interval 30
no atm ilmi-keepalive
dsl operating-mode auto
pvc 8/35
vbr-nrt 512 399 3392
encapsulation aal5mux ppp dialer
dialer pool-member 1
service-policy output Child
interface Dialer0
description PPP Session
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation ppp
dialer pool 1
ppp authentication chap callin
ppp chap hostname xx
ppp chap password xx

Similar Messages

Configuring PPPoE on 2801 with WIC-1ADSl

Hello All!
I try to configure 2801 with WIC-1ADSl
part of my config is:
interface ATM0/1/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
pvc 0/55
encapsulation aal5mux ppp dialer
pppoe-client dial-pool-number 1
interface Dialer1
ip address negotiated
ip mtu 1492
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname xxx
ppp chap password 0 xxx
ppp pap sent-username xxx password 0 xxx
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer1
show int dialer
but in this configuration i cann't connect to ISP (and recive ip address)
show int Dialer 1
Dialer1 is up, line protocol is up (spoofing)
Bound to:
Virtual-Access2 is up, line protocol is down
yourname#debug dialer packets
Dial on demand packets debugging is on
yourname#ping 195.161.136.2
Sending 5, 100-byte ICMP Echos to 195.161.136.2, timeout is 2 seconds:
*Mar 15 12:37:33.523: Di1 DDR: ip (s=192.168.0.230, d=195.161.136.2), 100 bytes,
outgoing interesting (ip PERMIT)
*Mar 15 12:37:33.523: Di1 DDR: Cannot place call, no dialer string set.
*Mar 15 12:37:35.523: Di1 DDR: ip (s=192.168.0.230, d=195.161.136.2), 100 bytes,
outgoing interesting (ip PERMIT)
Can anybody help me to correct problem?
Thank you very much

Tnank you very much!!!
the first part of my task is solved...
now my config is
yourname#show run
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
ip domain name yourdomain.com
vpdn enable
vpdn ip udp ignore checksum
interface FastEthernet0/0
description $ETH-LAN$$ETH-SW-LAUNCH$$INTF-INFO-FE 0$
ip address 192.168.0.230 255.255.255.0
ip nat inside
ip tcp adjust-mss 1452
duplex auto
speed auto
interface ATM0/1/0
no ip address
no atm ilmi-keepalive
dsl operating-mode auto
interface ATM0/1/0.1 point-to-point
pvc 0/55
oam-pvc manage
pppoe-client dial-pool-number 1
interface Dialer0
ip address negotiated
ip mtu 1452
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 2
ppp authentication chap pap callin
ppp chap hostname xxx
ppp chap password 0 xxx
ppp pap sent-username xxx password 0 xxx
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer0
ip nat inside source list 1 interface Dialer0 overload
access-list 1 permit 192.168.0.0 0.0.0.255
dialer-list 1 protocol ip permit
dialer-list 2 protocol ip permit
But I need to configure second chanel with PPPoEoA (ethernet over ATM or encapsulation MAC or Enet encap)encapsulation for access to inside SP network (172.16.x.x etc.)
How I can do this?

2821 Router with EVM-HD-6FXO

Hi all,
I want to buy a 2821 router with an EVM-HD-6FXO module. The 2821 is running IOS "c2800nm-ipbase-mz.124-15.T10.bin". My question is can I use the 2821 as a Gateway for CUCM v10.5 or if I have change upgrade the IOS to a different version.
Thanks.

Yes, run SIP or H323 which is version agnostic, even MGCP will work though according to Cisco 15.X code is required.
Chris

Could Cisco 1701 ADSL Router supports WIC-1ENET Card.

Hi,
I need advise as to if a Cisco 1701 ADSL router could support WIC-1ENET Card.
My 1701 Router has WIC 0 as ADSL and WIC 1 as ISDN, could the ADSL card be replaced by a WIC-1ENET. I noticed ,that the cards seems to be rivet onto the back of the Router and not connected with SCREWS as other routers would posses.
Could someone advised as to how i can have this router supports 2 Ethernet NICs or what could be your recommendations?
Thank you,
Cisco End User.

Hello,
the WIC-1ENET is supported on the 1701, but, AFAIK, only in slot 0.
It does not support 2 WIC-1ENET cards, only the 1720, 1750, and 1751 do, with a specific IOS release, check out this info from CCO:
WIC-1ENET- Support for two Ethernet WICs
The Ethernet WIC (WIC-1ENET) provides the capability to deploy additional Ethernet port(s) in a Cisco 1700 series routers. The initial release of the WIC-1ENET supported only one WIC-1ENET card in a 1700 router. The new IOS 12.2(2)XJ release offers the option of deploying up to two WIC-1ENET adapters in a Cisco 1720, 1750, or 1751 router. A total of three Ethernet ports can be configured. A typical application that requires three Ethernet ports involves using the built-in 10/100 Fast Ethernet port for LAN segment. One of the WIC-1ENET port could be used for high-speed broadband DSL or cable modem connection. The second WIC-1ENET port could be used for a DMZ (demilitarized zone) environment for deploying public Web servers or FTP servers. Hardware modification is not necessary to use the capability of IOS 12.2(2)XJ. The new IOS software is compatible with WIC-1ENET adapters already installed in 1700 series routers.
HTH,
GP

Cisco 2811 Router with 3 ADSL card and load balancing

Dear All,
I have few queries:
1. Does Cisco 2811 Router support 3 ADSL card?
2. We are the ISP. I want to do load balancing with 3 dsl
line on Cisco 2811 Router.
Please send me the linke for this configuration.
Thanks/Regards
Atul

hi
In 2811 you have 4 HWIC and 1 NME you can install 1-port ADSL WAN Interface Cardon the HWIC slots.
Also just enable 3 default (equal cost) routes towards the interfaces which will take care of the load balancing.
if you need more info and inputs do post out with ur requirements along with network topology in place at present..
regds

1750 router with wic-1enet

I have a cisco 1750 router. I just got a wic-1enet card for it. the router meets all the requirements for the card, and the slot 0 ok led is on. when I log into the console port and do "show interfaces" all I get is the fast ethernet that is onboard, and loopback0. ethernet 0 doesn't show up in there. am I doing something wrong or is there something I can do to try and fix the problem?

show diag gives me this:
Slot 0:
C1750 1FE VE Mainboard port adapter, 1 port
Port adapter is analyzed
Port adapter insertion time unknown
EEPROM contents at hardware discovery:
Hardware revision 5.2 Board revision C0
Serial number 2660151875 Part number 73-3743-05
Test history 0x0 RMA number 00-00-00
EEPROM format version 1
EEPROM contents (hex):
0x20: 01 C9 05 02 9E 8E B2 43 49 0E 9F 05 00 00 00 00
0x30: 60 00 00 04 00 00 00 00 00 00 00 00 00 00 00 00
WIC Slot 0:
Unknown WAN daughter card
Hardware revision 64.0 Board revision G0
Serial number 0960561920 Part number 130-18710-165
Test history 0x03 RMA number 66-65-48
Connector type PCI
EEPROM format version 4
EEPROM contents (hex):
0x20: 04 FF 40 00 39 41 03 00 82 49 16 A5 03 42 41 30
0x30: 80 00 00 00 00 02 02 C1 8B 56 4D 53 30 36 32 36

Connect to router with airport extreme card

Hello, I just oredered a iBook G4 off of Amazon (1.33 GHZ, 1 GB RAM, Combo, 12") with an Airport Extreme card. Can this connect to my Linksys WPA wireless router? I'm new with Macs, so sorry if noobish.

AirPort Extreme Card M8881LL/A
802.11 b/g
Frequency Range 2.4 GHz
Data Rate Up to 54Mbps
Channel Support 802.11b/g:
US/Canada/Latin America/Taiwan: 1-11
Japan: 1-14
Other countries: 1-13
Security 40/128-Bit WEP, WPA, NAT Firewall, MAC address filtering
Antenna Internal
Operation Distance 150 feet
Transmission Power 15dBm

How to choose router with G.SHDSL cards

Hi all,
Is everyone can help me how to choose the right router? we would like to purchase a router support 4 LAN ports, 2 x modem SHDSL and tunel VPN IPSec 10 mini.
Thanks in advance.
Raj

You can use any router listed in the data sheet.
http://www.cisco.com/en/US/prod/collateral/modules/ps5949/data_sheet_c78-599774.html
There is also a newer model released:
http://www.cisco.com/en/US/prod/collateral/modules/ps5949/data_sheet_c78-692767.html

L2TP network server 2821 router?

Can 2821 router with appropirate IOS image be L2TP network server and support 400-500 L2TP simultaneous connections? We want to use access VPDN that uses L2TP as tunneling protocol to provide remote users access to our services and to the Internet.

Hi Marija,
That's right, the 2821 can be used as an L2TP server (LNS or LAC).
It supports 900 IDBs, which means that you can provide access to around 900 remote-users. Also, it supports a maximum of 880 L2TP sessions/tunnels.
You can find detailed information on the following link:
http://www.cisco.com/en/US/tech/tk827/tk369/technologies_design_guide_chapter09186a00800d9cc7.html
Regards,
Juan Corrales

1600 Series Router & WIC-1ADSL

I have some 1600 series routers and was hoping to use them for my Broadband connection.
Is this WIC compatable with the 1600 series router?
What is the required IoS if this is posible?
Thanks Ian

Ganesh,Thank you for the response, however, that article is for the WIC-1DSU-T1 as far as I can see.I was wanting information regarding the WIC-1ADSL. which does not appear to be recognised in my 1603R routers.Thanks Ian
Ian,
The ADSL WAN interface cards (WICs) supported on the Cisco 1700/2600/3700 series routers are also supported on the Cisco 1800 (modular), 2800, 3800 series Integrated Services Routers (ISRs).
As per the link it start supported only from 1700 series routers ony.
Check out the below link hope that clears out your query !!
http://www.cisco.com/en/US/prod/collateral/routers/ps221/product_data_sheet0900aecd8028aa5a.html
If helpful do rate the valauble post
Ganesh.H

Hi, I have a power Mac G5 with an airport card and I am having a hard time connecting to my regular NETGEAR router. Any help, Hi, I have a power Mac G5 with an airport card and I am having a hard time connecting to my regular NETGEAR router.PLs help

Hi, I have a power Mac G5 with an airport card, MAc OS X 10.5.8, Wireless card is Airport Extreme ( 0x14E4,0x4E ) and I am having a hard time connecting to my regular NETGEAR router. PLS Help,
Thanks,
Mishcadola

I spent 2750 $ for my 24" iMac (price for my region)...
And the perfect world of Steve Jobs still close, but never we've been in there!

Cisco 3925 router with an ATM E3 card that never goes down!

Hi all,
We a Cisco 3925 router with an ATM E3 card (NM-1A-T3/E3) configured as below with 1 PVC. we see that the ATM subinterface we created for the PVC never goes down! not even when the WAN link is down! The problem with this is we are tracking the line protocol of the ATM sub interface to have VRRP failover to standby router. But because of this issue only BGP goes down whenever the WAN is down & line-protocol of the Subinterface remains up, the failover never happens & site is down. We can configure VRRP to track reachability of a BGP route as workaround but I would like an explanation or troubleshooting steps to check whats the trouble with current setup?
Cisco IOS Software, C3900 Software (C3900-UNIVERSALK9-M), Version 15.1(2)T4.1, MAINTENANCE INTERIM SOFTWARE
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2011 by Cisco Systems, Inc.
Compiled Tue 30-Aug-11 08:44 by prod_rel_team
card type e3 1
interface ATM1/0
description Link to PE
mtu 1500
bandwidth 34010
no ip address
no ip proxy-arp
logging event subif-link-status
no atm ilmi-keepalive
no atm enable-ilmi-trap
end
interface ATM1/0.101 point-to-point
description PVC to MPLS PE
mtu 1500
bandwidth 2500
ip address a.b.c.d 255.255.255.252
no ip proxy-arp
ip flow monitor FMforIP4in sampler ata1to100 input
ip flow monitor FMforIP4out sampler ata1to100 output
ip nat outside
ip virtual-reassembly in
no atm enable-ilmi-trap
snmp trap link-status
pvc 1/101
vbr-nrt 8192 8192 1
vc-hold-queue 2048
oam-pvc manage
oam retry 3 5 1
oam ais-rdi 15 3
encapsulation aal5snap
protocol ip inarp
queue-depth 5 3
service-policy out Edge_Queueing
end
Thanks a lot in advance!

Your router has some configuration on it already and it would help us give you better advice if we knew what is already in the configuration. So would you post the output of show running-config (if there is sensitive information like addresses and passwords you can mask them out.
Changing the configuration register was a good start. I have a couple questions/observations that may help you get started. I notice what appears to be the same public IP address on Gig0/0 and on multilink. Did you get that address from your ISP? If so what kind of connection do you have to the ISP?
In your description you tell us that Gig0/0 is connected to a small switch, which I assume is for the LAN of your network. But that also is the interface where the public address is configured. So I am confused whether this interface is for LAN or for connecting to the ISP. Can you clarify this?
HTH
Rick

2811 w/ WIC-1ADSL-I-DG PPPoA issue

Hello:
I have been trying to test our new office gear prior to move, specifically the DSL WIC card.
It seems I have all the config correct but I fail to negotiate link and I am not getting much info from a debug standpoint leading me to believe: -1- PPP isn't quite set up correctly -2- the WIC is possibly bad.
Would it be possible for someone to review my config since I can find nothing on the web that serves as a decent example of using this WIC card with Qwest?
DETAILS:
Info pulled from my old Actiontec modem for testing purposes:
VPI/VCI = 0/32
DSL Mode = MMODE
DSL Negotiated Mode = T1.413
Up/down = 7168/896
ATM QoS class = UBR
The connection is doing PPPoA, evidently it is using PAP per my ISP (qwest does the local loop, my own ISP the VC termination and routing)
Cisco 2811 and WIC setup:
interface ATM0/1/0
description QWEST DSL - circuit id:
no ip address
no ip mroute-cache
shutdown
no atm ilmi-keepalive
dsl operating-mode auto
dsl enable-training-log
pvc 0/32
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dialer1
ip address negotiated
encapsulation ppp
dialer pool 1
ppp authentication pap
ppp pap sent-username <username_goes_here> password 0 <passwd_goes_here>
Additionally, it would be helpful if you provided what all the 'Modem States' are. For example, Modem state = 0x8 is in many docs but you don't say anything about 0x3. Its helpful to know all the codes for Modem state if your going to recommend doing debugs of atm events for troubleshooting. Hence, the post to the forum. I can't get link and everything appears to be set up properly.
Thanks for the insight/answers.

No, I am afraid we don't do ADSL over ISDN. My boss ordered the equipment and I think the reseller wasn't too bright.
So would I be correct that I am going to have to have a WIC-1ADSL or a HWIC-1ADSL?
I see that this ADSL over ISDN card we have currently does support T1.413, but given I can't get link I am guessing that is only T1.413 when over ISDN so I have to use one of the other types of WICs listed above if this is over POTS.
If someone from Cisco or otherwise can confirm that would be great so I can go ahead and get the right card shipped to us ASAP.
Thanks for the assist,
-Jeff
Thanks for pointing that out. I suspected it might be the issue but have not ordered or touched many DSL WICs in my day, only the bigger chassis's that terminate the traffic on the provider end.

WIC-1ADSL Won't No Shut in 1751V

Installed a new WIC-1ADSL in my 1751V yesterday. It sees the card fine, but I cannot get the IF to talk to the line. SO, I do a debug and get the following:
01:44:29: DSL: No response on write to 0x0
01:44:29: DSL(ATM0): Could not download ASW_init_3_8_131.bin
01:44:41: DSL(ATM0): No response from ASW_init_3_8_131.bin
01:44:41: DSL(ATM0): Unexpected response 0x0 to ASW_init_3_8_131.bin
I am not familiar with this error, nor could I find any indications, other than that a
failure to come up appears to point to an error in framing configuration.
Would you be kind enough to give me some potential pointers on how to best deal with this error? Is the ASW_init a file that would work if I load a new IOS in the machine, and if not, where would it be drawn from?

Homeland#show config
Using 1630 out of 29688 bytes, uncompressed size = 2738 bytes
Uncompressed configuration from 1630 bytes to 2738 bytes
version 12.2
service timestamps debug uptime
service timestamps log uptime
service password-encryption
service compress-config
hostname Homeland
boot system flash
logging buffered 8012 errors
logging rate-limit console 100 except errors
enable secret 5
enable password 7
memory-size iomem 25
clock timezone CST -5
ip subnet-zero
no ip routing
interface ATM0
no ip address
no ip route-cache
no ip mroute-cache
no atm ilmi-keepalive
pvc 0/32
encapsulation aal5mux ppp dialer
dialer pool-member 1
dsl operating-mode auto
interface FastEthernet0
ip address 10.10.10.3 255.255.255.0
no ip route-cache
no ip mroute-cache
speed auto
full-duplex
interface Virtual-Template1
no ip address
interface Dialer1
ip address 255.255.252.0
ip nat outside
encapsulation ppp
dialer pool 1
dialer-group 1
ppp authentication chap pap callin
ppp chap hostname
ppp chap password 7
ppp pap sent-username password 7
ip nat translation timeout never
ip nat translation tcp-timeout 345600
ip nat translation udp-timeout 345600
ip nat translation finrst-timeout 345600
ip nat translation dns-timeout 345600
ip nat inside source list 102 interface Dialer1 overload
ip classless
ip route profile
ip route 0.0.0.0 0.0.0.0 Dialer1
no ip http server
access-list 102 permit ip 10.10.10.0 0.0.0.255 any
snmp-server community public RO
snmp-server enable traps tty
call rsvp-sync
dial-peer cor custom
banner motd ^C
Welcome to HOMELAND router.
^C
line con 0
line aux 0
line vty 0 4
password 7
login
no scheduler allocate
end
Homeland#

CCP Express wont install on 2821 router

Hello everyone,
I am trying to install Cisco Configuration Professional 2.4 Express on my 2821 router. During the installation process, I get notified there is 0 bytes available of routers flash memory. When I run a "show flash:" command, I receive the following error:
%Error show flash: (No device available)
The output of the "show version" (edited) command is:
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 12.4, RELEASE SOFTWARE (fc1)
ROM: System Bootstrap, Version 12.4(1r) [hqluong 1r], RELEASE SOFTWARE (fc1
Router uptime is 2 weeks, 5 days, 4 hours, 54 minutes
System returned to ROM by power-on
System image file is "flash:c2800nm-adventerprisek9-mz.124-12c.bin"
Cisco 2821 (revision 53.51) with 512000K/12288K bytes of memory.
Processor board ID FTX1006C4SB
2 Gigabit Ethernet interfaces
1 Serial interface
2 Virtual Private Network (VPN) Modules
DRAM configuration is 64 bits wide with parity enabled.
239K bytes of non-volatile configuration memory.
500976K bytes of ATA CompactFlash (Read/Write)
Configuration register is 0x2102
After some reading on Cisco site, I saw that 2800 routers do not support internal flash, but only CF cards. What I would like to know is how can I install CCP Express on CF card?
Thank you in advance.

bump?

2821 Router with wic-1ADSL card

Similar Messages

Maybe you are looking for