5600FX S-Video signal but no Composite signal

Hi,
I have just build my new PC, MoBo MSI KT6 Delta, and graphics MSI 5600FX 128Mb, as you can see I like MSI,
My problem, when I connect my TV (Composite connector) to the Graphic card(Conversor cable S-Video to Composite) I select in the nvidia options Monitor +TV, If I select in the TV options S-Video I see Black and White, this is normal(TV input is composite),  everything is fine, but when I select Composite I cant see anything on the TV  (BLACK),
I always watch the PC on my TV with all the grafics I have had(4).
I think that it is a hardware issue but before to change the gc for another one()  I would like to know if there is a solution to this issue.
Drivers.. I have try with the last one and one version before, os XP Prof
Thanks

If it shows connected ... then check the Ip address under the same ... also you if are getting Ip - 192.168.1.X ... with gateway -- 192.168.1.1 ... try tro ping 192.168.1.1 ... if getting replies .... try to ping 4.2.2.2 & yahoo.com ....
Check the results ...
If you are not getting replies .... disable the firewall on the computer & then try to ping the gateway ....
let me know the status ...

Similar Messages

  • TS3623 I rented a movie and can watch preview perfectly with video and audio feed as signal strength is at top when I checked. However, when I purchased rental video is fine , but I get scratched sound for audio. Any thoughts to fix?

    I rented a movie and can watch preview perfectly with video and audio feed as signal strength is at highest when I checked. However, when I purchased rental video is fine , but I get scratched sound for audio. Any thoughts to fix? I rented movie within week and it worked. All previews of movies and show also works.

    I have a suspicion that the problem is not in the recording device itelf, but rather in the playback-software, which is struggling with an unfamiliar audio format/codec/whatever-it's-called... I opened the file in QuickTime Player 7 (7.6.6) and selected "Show Movie Properties" and it says:
    "Video Track: H.264
    Sound Track: Integer (Little Endian)"
    All current Mac systems support Integer (both Big and Little Endian) audio natively. The fact you can hear anything at all proves that the audio is playing back. The most likely problem would be a malfunction associated with the mic pickup.

  • Fire Wire Component or Composite signal

    Just curious, I've never really been informed or found the answer to this:
    Is Fire Wire a component or composite video signal. I've heard agruements that it's both.
    Thanks,
    ed

    all the formats in the D7 format (DV, DVCPRO, DVCAM, D8) are all Digital component
    D1 (8-bit), D5 (10-bit), D9 (digital S) and DVCPRO 50 are also all Digitial Composite signals<<
    The formats yes ... but Firewire isn't a format. It's just a data transfer protocol.

  • Convert mini display port signal to a composite by software

    I have already bought a VGA to RCA cable and when I connect it to my original Apple MDP to VGA adapter the screen freaks out. Most probably it's because the 3rd party cable has to receive a composite signal and not an separate RGB + other signals (Hor Sync, Ver Sync) etc.
    When I was searching for these kind of adapters I sometimes read that one has to check if his computer can output a tv signal from their VGA port. Most probably they would be referring to the fact that your computer has to manage to output a composite signal through your VGA port.
    So I was wondering if there is a way to get my mac to output a composite signal from my mini display port using some kind of software.
    Thanks for your help in advance.

    Hi Jim,
    Just to clarify, you state that you have a MacBookPro5,1, which is the late 2008 model. The video output on that model is a mini-DisplayPort, not a mini-DVI (like the pre-unibody MacBooks) or a micro-DVI (like your 1st gen MBA). DisplayPort is a different type of port. (Note - I requested an edit of the title of your post to clarify that).
    When you connect the TV, in what sequence are you connecting? The 'proper' sequence is to connect the DVI-HDMI cable to the mini-DisplayPort to DVI adapter, have the HDMI end connected to the TV, have the TV set to Line-In, looking for a signal, then connect to the MBP last.
    What happens when you connect it like that? Have you tried System Preferences > Displays > Detect Displays?

  • 790XT G45 All Works but no vga signal

    Please see specs in signature, i bought new chassis as below and since the transfer, no boot, everything runs cpu fan etc. but no vga signal.

    Ensure that all power cables are connected.
    Else:
    Motherboard Grounding to case causing No Post
    Test the motherboard outside of the case to verify that the motherboard is not shorting to the case and causing a problem
         •    With only the CPU and heat sink, memory, and video card (or onboard video) connected to the motherboard, place the motherboard on a non-conductive surface and retest the motherboard
         •    Check the case mounting standoffs to verify that they are lining up correctly with the mounting holes on the motherboard.

  • HT4623 i have issue with my iphone5, the phone is open and good network signal, but when some one calling me they cant reach me, like the phone is off

    i have issue with my iphone5, the phone is open and good network signal, but when some one calling me they cant reach me, like the phone is off

    You are as far as you can be with the original iPad; only iPad 2 and greater will update to 7+

  • How do I set up LiveRig or TouchOSC with Mainstage 2.2.2? Both apps send signals but none are received by Mainstage and both the ipad 3 (6.1) and macbook pro (10.7.5) see each other via WIFI?

    As I said before both app's send signals but none are received by Mainstage and both the ipad 3 (6.1) and macbook pro (10.7.5) see each other via WIFI on the network set up, which I think I did right. I have tried MIDI Disigner and Mainstage shows MIDI activiti, what can I be doing wrong?
    Thanx in advance.

    I agree anti-relay can be using UBE feature. However, there is serious problem in reject the spam mail. My nms is using UBE feature to stop spam mail. According to the work flow of the UBE, the mail is received by nms completely and UBE is going to invesgate the mail address. Although UBE can stop the spam mail, the spam mail have a trouble in returning the mail to the sender. The reason is the sender address is usually not existed in the world. That will cause a lot of mail waiting in the mail queue.
    In my experience, do not use UBE for anti-relay.

  • Time capsule produces a signal, but won't connect or backup

    I have looked at some of the other discussions here; some are similar, but I can't find an answer.
    I have a TC, Macbook Pro and an iPhone 4, all between 6-10 months old.   My problems started when I turned on all my stuff after being away for 4 weeks over the summer.
    My Macbook pro's AirPort recognises the TC - I have a 'full signal' reading at the top of the page.  However, when I try and connect to the internet, I'm told it can't connect to the server.  If I just keep trying, re-entering addresses (from the scroll-down bar, so always exactly the same), it eventually connects and I have a great connection, which I can use to watch movies/download stuff no problem.  Why is it so **** illogical?  Why does it connect on the 20th attempt, and not on the first?  This happens however long the computer has been on, and regardless of when I last connected to the internet.
    The biggest problem is that I have a Vodafone 'Sure Signal' signal booster attached to the TC.  Without it, I get no phone signal.  The Sure Signal does not recognise the signal from the TC at all.  I have done factory resets on both - individually and together, and nothing has changed.  I have turned the Sure Signal off, but the TC still doesn't work properly. 
    My iPhone won't connect either.  It too shows a 'full signal', but when I try and connect it says connected/not connected alternately about every 1 second.
    The TC is connected to the internet via a cable from my landlord's router, next door.  They have perfect signal.  They also have a signal booster in their house, which used to interfere with my TC (when it worked).  I changed the channel on my TC, and now, when it connects, there is no interference.
    Please can someone enlighten me - I have worked though every thing I can, and I can't go any further because I can't see any logic to the problem.
    ** Since these problems have started, the TC has not backed anything up - I can't get it to back up, whatever I've tried.
    ** Each time I have re-made my network, when I open Airport Utility, it says 'no wireless devices recognised', and I have to re-start the TC in order to be able to do anything to it.

    Try changing the Firewall setting:
    mDNSResponder - Allow incoming connections
    Background:
    My Time Capsule was working perfectly in Leopard.
    When I upgraded to Slow Leopard, Airport Utility was no longer able to see the Time Capsule - although my Mac (MBP) was still able to connect to the wireless network and out onto the Internet.
    The next day or so I upgraded to Lion (Snow Leopard was only installed to get App store) - the situation remained the same.
    From another Mac (MB - still running Leopard) Airport Utility was still able to connect to Time Capsule.
    I edited the firewall settings on my Lion MBP:
    The mDNSResponder was set to "Block incoming connections".
    I changed this to "Allow incoming connections".
    Airport Utility was then was then able to see the Time Capsule (I can't recall now if I needed a reboot after changing this).
    HTH.

  • My WiFi pick up the signal, but I can't do anything with internet.

    I was browser the web the other day, and all the sudden everything stop loading, and after that I can't go to any site. any more. but as I check of the log, I doesn't see any problem. and I can tell the system do pick up the signal, but I just can't go online.
    here is what I have check:
    ioky@Varius:~$ sudo iwconfig
    lo no wireless extensions.
    eth0 no wireless extensions.
    eth1 IEEE 802.11b ESSID:"linksys" Nickname:"ipw2100"
    Mode:Managed Frequency:2.437 GHz Access Point: 00:0C:41:84:3B:BE
    Bit Rate=2 Mb/s Tx-Power:16 dBm
    Retry short limit:7 RTS thr: off Fragment thr: off
    Encryption key: off
    Power Management: off
    Link Quality=72/100 Signal level=-80 dBm
    Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
    Tx excessive retries:0 Invalid misc:3 Missed beacon:0
    eth1 Scan completed :
    Cell 01 - Address: 00:12:0E:0F:50:02
    ESSID:"05B408577194"
    Protocol:IEEE 802.11bg
    Mode:Master
    Frequency:2.437 GHz (Channel 6)
    Encryption key: off
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
    11 Mb/s; 12 Mb/s; 18 Mb/s; 22 Mb/s; 24 Mb/s
    36 Mb/s; 48 Mb/s; 54 Mb/s
    Quality:53 Signal level:0 Noise level:0
    Extra: Last beacon: 216ms ago
    Cell 02 - Address: 00:13:10:1B:71:54
    ESSID:"Chidori"
    Protocol:IEEE 802.11bg
    Mode:Master
    Frequency:2.437 GHz (Channel 6)
    Encryption key: on
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
    11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
    48 Mb/s; 54 Mb/s
    Quality:37 Signal level:0 Noise level:0
    IE: WPA Version 1
    Group Cipher : TKIP
    Pairwise Ciphers (1) : TKIP
    Authentication Suites (1) : PSK
    Extra: Last beacon: 212ms ago
    Cell 03 - Address: 00:13:10:73:95:5A
    ESSID:"ptak"
    Protocol:IEEE 802.11bg
    Mode:Master
    Frequency:2.462 GHz (Channel 11)
    Encryption key: on
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
    11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
    48 Mb/s; 54 Mb/s
    Quality:31 Signal level:0 Noise level:0
    Extra: Last beacon: 0ms ago
    Cell 04 - Address: 00:0C:41:84:3B:BE
    ESSID:"linksys"
    Protocol:IEEE 802.11b
    Mode:Master
    Frequency:2.437 GHz (Channel 6)
    Encryption key: off
    Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 11 Mb/s
    Quality:31 Signal level:0 Noise level:0
    Extra: Last beacon: 208ms ago
    ioky@Varius:~$ sudo dhclient eth1
    Internet Systems Consortium DHCP Client V3.0.6
    Copyright 2004-2007 Internet Systems Consortium.
    All rights reserved.
    For info, please visit http://www.isc.org/sw/dhcp/
    Listening on LPF/eth1/00:0c:f1:3a:b5:02
    Sending on LPF/eth1/00:0c:f1:3a:b5:02
    Sending on Socket/fallback
    DHCPREQUEST of 192.168.1.104 on eth1 to 255.255.255.255 port 67
    DHCPACK of 192.168.1.104 from 192.168.1.1
    bound to 192.168.1.104 -- renewal in 33768 seconds.
    ioky@Varius:~$ sudo ifconfig eth1
    eth1 Link encap:Ethernet HWaddr 00:0c:f1:3a:b5:02
    inet addr:192.168.1.104 Bcast:192.168.1.255 Mask:255.255.255.0
    inet6 addr: fe80::20c:f1ff:fe3a:b502/64 Scope:Link
    UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
    RX packets:145 errors:0 dropped:0 overruns:0 frame:0
    TX packets:175 errors:0 dropped:0 overruns:0 carrier:0
    collisions:0 txqueuelen:1000
    RX bytes:16023 (15.6 KB) TX bytes:12958 (12.6 KB)
    Interrupt:11 Base address:0x2000 Memory:cfffe000-cfffefff
    ioky@Varius:~ ping google.com
    ping: unknown host google.com
    I have no idea what is going. could anyone give me a hand?
    Thanks

    Can you ping one of google's IP addresses? for ex. 72.14.207.99   If you can you may want to check /etc/resolv.conf and see if your DNS IP is entered correctly.

  • I connected my ipod touch 4g wi-fi with laptop ad hoc network....it's showing wi-fi signals but internet is not working...what is the problem in that can anyone help me...inadvances thanks

    I connected my ipod touch 4g wi-fi with laptop ad hoc network....it's showing wi-fi signals but internet is not working...what is the problem in that can anyone help me...inadvances thanks

    my laptop is Windows 7 and ip is this
    192.168.102.12
    255.255.255.0
    192.168.102.1
    DNS
    192.168.254.2
    192.168.254.3
    in ipod touch 4g is DHCP and its showing
    ip address 169.254.192.139
    subnet mask 255.255.0.0.
    remaining all blank

  • MacBook pro Late 2011 detect external monitor but still not signal on it

    Good day.
    I have MBP 13" Late 2011
    Processor  2.4 GHz Intel Core i5
    Memory  4 GB 1333 MHz DDR3
    Graphics  Intel HD Graphics 3000 384 MB
    Software  Mac OS X Lion 10.7.4 (11E53)
    Mini display to DVI adaptor and Acer monitor conected with DVI cable
    P225HQL:
      Resolution:          1920 x 1080 @ 60 Hz
      Pixel Depth:          32-Bit Color (ARGB8888)
      Display Serial Number:          LLD0D0038515
      Mirror:          Off
      Online:          Yes
      Rotation:          Supported
    As you see it's detected by MBP but says "no signal". I tried all suggestions found here and anywere else but no solution still found. And of course i tried Detect Display and changing resolutions.
    Is there any way to make it just work!?

    I've just found out that my Macbook's Bluetooth spec is Bluetooth 2.0+EDR and my keyboard's Bluetooth is 3.0. Would this be of any issue?

  • The computer sees the airport signal but cannot connect to the internet

    I have a imac g5 connected wirelessly to my base station & an airport express. The mac part connects to the internet using the network without any problem. My problem is that the pc portion (using Windows XP) of my imac will not connect to the internet using the wireless network. It shows a strong signal but no connectivity. One of the comments that comes up is that the network didn't assign a network address to the computer (I assume the PC portion). Any thoughts how I can get my computer to connect to the wireless network from the PC portion of my mac.
    many thanks.

    Make sure your Firewall settings are correct. I'm going to share some of my settings in the PC area (please bear in mind that these IP addresses could differ from system to system)
    My Windows Firewall is DISABLED. You could do the same temporary and see if it works. I use Zone Alarm Pro Firewall. Make sure in my Control Panel ==> Network connection status, your device shows Airport Express wireless device or router.
    Depending in your Internet service provider and geographical zone the IP address could be different.
    Example:
    Zone Alarm Windows settings:
    TRUSTED ZONES ==> Loopback Adapter 127.0.0.0.1
    PC IP address 192.169.1.3 (example)
    Gateway 192.169.1.254
    DHCP Server 10.0.1.1
    DNS 10.0.0.1
    IN AIPORT EXTREME SETTINGS ( Make sure you are in your Imac side or Mac Os)
    Id 192.169.1.5
    Subnet Mask 255.255.255.0
    Router 192.169.1.254
    Connection Automatic
    Ethernet ==> Automatically (through Airport Utility)

  • My iPod touch gets wi-fi signal, but doesn't work..?

    i've had my ipod touch for about a year and i use my friends wi-fi all the time at her house. she has a linksys router and cable internet. i recently got at&t internet, which is dsl. the internet modem also works as a router, with wi-fi. i can connect to the wi-fi perfectly. with a strong signal, but when i go to safari, or itunes, or anything. it says "unable to connect to the server" WHY!?
    ): help me please?

    ok so i have a cable modem type of internet provider; we use a dlink router because we have 3 common laptops. Neither my personal laptop with windows xp pro conects to the network well it comes out as limited connection and on my itouch the network appears, it has the checkmark, it has an ip address and subnetmask or whatever you call it. the connected symbol appears on the top bar next to IPOD. and yet I cant connect to anything it says in safari or facebok that it can't open or continue because im not connected to the internet. and it won´t connect to any wifi network anymore. so i've reset the network settings, i've reset all settings to see if it works again but nothing. It used to work well but don't know if some app or content or the itunes of the computer is making it unavailable to connect to the internet.

  • My ipod touch will recognize my home wireless network but when I try to select it the wheel just keeps spinning. It looks as though I have a good signal but my router is an older apple extreme. I've updated to the lasted firmware but it's still not workin

    My ipod touch will recognize my home wireless network but when I try to select it the wheel just keeps spinning. It looks as though I have a good signal but my router is an older apple extreme. I've updated to the lasted firmware but it's still not working. I have two older imacs and a wii that connect to the router. Any thoughts? Thanks

    - Reset the iPod. Nothing will be lost
    Reset iPod touch:  Hold down the On/Off button and the Home button at the same time for at
    least ten seconds, until the Apple logo appears.
    - Power off and then back on the router
    - Reset network settings: Setting>:General>Reset>Reset Network Settings.
    - iOS: Troubleshooting Wi-Fi networks and connections

  • I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

    I JUST BOUGHT AND INSTALLED A LINKSYS E1200 WIRELESS N ROUTER AT HOME. MY IPHONE CONNECTS WITH A STRONG SIGNAL BUT WHEN I TRY TO USE THE INTERNET IT JUST LOADS FOREVER. HOW CAN I FIX THIS?????!!!!

    RESET YOUR ROUTER
    No. Reset your router.

Maybe you are looking for