975x stuck at "Verifying DMI Pool Data"

Hey-- I just replaced my stock intel heatsink with a new Noctua NH-U12F. It requires a backplate, so it takes unbuilding and rebuilding your computer to put on.
Somewhere in the rebuilding process, something went wrong. My boot process gets stuck on the "Verifying DMI Pool Data....." stage. It has never done this before. I pushed the BIOS Reset button and it didn't fix it, i'm running BIOS 7.0 (stock)
I'm looking at it right now it's been there for a good 2 minutes
MSI 975x Plat PUE
intel E6600 : Noctua NH-U12F
ATi 512MB X1900XTX
Corsair DDR2 667 2GB
WD Raptor
WD Caviar
NEC dvdr/w
Ultra 600W x-finity
I don't have a case speaker so there's no beeps :-/
Thanks in advanced, you guys always help me out tons

yeah that's what i meant by bios reset button
i poked around online--could be a million things
so i tried them one at a time, it was my HDD boot priority out of order.
sorry i panicked on you guys
hope you're having a nice night/day as it may be around you (it's 3:45 in the morn here :()

Similar Messages

New Build hangs at VERIFYING DMI POOL DATA

I put it all together and try to load the XP OS, but it hangs at Verifying DMI Pool Data.......(NTLDR is missing)
Have rechecked the cables and connections a half dozen times. (All new cables)
Checked and rechecked the boot order.
Disconnected the floppy.
I tried swapping to another HDD with a SATA, but I don't see it recognized during post, and I still get error message.
I put in an XP ms-dos starup floppy and it says update success, but won't system file transfer and goes back to the original error message.
What's up here?
I little surfing lead me to this link http://www.duxcw.com/faq/computer/dmi.html
which says a possible cure might be clearing the CMOS.
I supposed that's done by changing the jumpers right?
But, I have searched this website and can't find any Bios downloads for the K8N Neo2.
If I clear the CMOS I'll need to DL BIOS again right?
I am sure the original V1.A is outdated anyway.
Suggestions? I don't want to go rooting around and changing things and make this worse.
This is my 2nd build and the 1st wasn't easy either.
MSI K8N Neo2 (AMD 939 socket) Mobo
AMD 3000+ / 2 X 512mb Corsair VS DDR400 Ram
120GB IDE133 Maxtor HDD
Asus NVidida Geforce4 ti4800se 9480 8x AGP
Rosewill RS2 500w PS (24 pin adapted to 20 pin)

Quote from: at2wooden on 04-December-05, 05:34:49
thanks......got the startup screen back but,
I am right back where I started.....Hangs at Verifying DMI Pool Data / missing NTLDR.
I did not install a new hard Drive, but a good pull from my old system.
Drive contanins data, but I should be able to format during OS install right?
Hmmmmmmmmmmmmmmmmm.
MSI K8N Neo2 (AMD 939 socket) Mobo <New>
AMD 3000+ / 2 X 512mb Corsair VS DDR400 Ram <New / New>
120GB IDE133 Maxtor HDD <known Good>
Asus NVidida Geforce4 ti4800se 9480 8x AGP <Used>
Rosewill RS2 500w PS (24 pin adapted to 20 pin) <New>.
yes just BOOT from CD and reinstall XP... better reformat partition which contains XP. if you have important things on this partition not only OS move it to secondary partition or to other HDD.

WAT DOES "VERIFYING DMI POOL DATA" MEANS?

i bought a sempron 2800+ and my msi motherboard is k8m800-ce from newegg and i set everything up i hope. when i boot up it was sloww and then after awhile it boots up faster. i used an old hdd from my old comp (ata-133) wd 80gb. i tryed to format but it wont let me do the commands. maybe i need a new hdd? i restarted the computer and see wat happens, it keeps on sayin "VERiFYIN DMI POOL DATA" what does this mean? rite now im goin to buy a maxtor 100 gb sata/150 and see if that will work. im installin win98 se then winxp. anyone knows wats teh prob? or if anyone else bought the same cpu or mobo have had these prob?
i have a 512 corsair memory pc3200, and one burner.

Clear CMOS Guide - read that for how to clear the CMOS, and refer to your manual for location of the CMOS jumper (JBAT1)
did you do (or attempt) a fresh install of Windows?
best to just do a clean install of XP, rather than install 98 and then upgrade

Can't get past "Verifying DMI Pool Data"

Hello forum folks, I'm hoping you can advise me on my problem. Here's my setup:
MSI VIA K8T800 K8T Master2-FAR
Dual AMD Opteron 240's (not overclocked)
ENERMAX 550W Power Supply Model "EG651P-VE(FMA)"
Sapphire ATI Radeon 9800XT Video Card, 256MB DDR
Corsair XMS Extreme Memory Speed Platinum Series, Low Latency (Twin Pack) 184 Pin
1GB(512MBx2) ECC Registered DDR PC-3200
Asus Black 16X DVD-ROM Drive, Model DVD-E616P1 Black
VANTEC Nexus Fan Controller Panel Model "NXP-205-BK"
with 5 Coolmax Chameleon LED cooling Fan, Model "CM-825-CL" connected
Western Digital Raptor 36.7GB 10,000RPM SATA Hard Drive, Model WD360GD
SONY Black 1.44MB 3.5inch Floppy Disk Drive, Model MPF920
When I first turned the computer on, my floppy wasn't being recognized, but the computer did get past the DMI verification. However, since my floppy wasn't working, I couldn't get Windows XP to install since I didn't have the SATA drivers. So, I fiddled with the floppy cable until it worked. Once I got the floppy working, the computer would start hanging on the DMI verification. So I unplugged the floppy but it still wouldn't go. I scanned the forum for ideas and tried clearing the CMOS and setting the BIOS settings to both the optimized defaults and the fail-safe defaults. I haven't yet had the time to unplug each device individually, nor have I unplugged every device. I'm wondering if anyone has any other advice. I'm hoping I won't have to RMA the board, but I will as a last resort.
Thanks for any help.
Edit: Forgot the PSU, heh.

UPDATE:
Okay, I've tried unplugging individual devices and it seems when the Raptor SATA drive is unplugged, it will get past the DMI verification, but when I plug the drive back in, it says, "Updating ESCD ... Success" and then hangs after the DMI verification line. I've tried switching from legacy power to SATA power, reversing the SATA cable, plugging the SATA cable into SATA1 and SATA2 on the MoBo and none of that has worked. Do I have a bad HD or am I still missing something?

Solaris 8 x86 Hangs on reboot with Verfying DMI Pool Data

I've just installed solaris 8 on intel. I previously run 2.7 on same system no problem.
After installing 8 and rebooting the machine hangs after displaying
Verifying DMI Pool Data .........
It appears to of verified, but then does nothing else. I have checked all components are compatible (supported), tried differing rebuilds, upgrading from 2.7 However every time I get the same problem.
Any ideas?
alan (every).

Green,
I need you to think really hard here with me...what was the last program, piece of hardware you loaded into the machine? I've seen this problem so many times and it will drive you wild...you're having a driver or software issue during bootup and it's hanging the system..
What I would do is see if I can get into safe mode by hitting F8 as the system starts up...if it will boot into safe mode then go uninstall whatever the program is that you installed last or uninstall the drivers of whatever hardware you installed last...
Then try rebooting again normally...
I'll warn you now that I've only been successful in doing this when I've rebooted the system twice prior to trying this fix...if you rebooted more than twice it will corrupt your MBR and you'll have to FDISK and start all over again...
Insert your boot disk Win98SE preferred...select Boot from floppy with no CDROM or Network...
Type FDISK at the A prompt...go in and delete the non dos partition...DON'T CREATE ANOTHER PARTITION OR FORMAT THE DRIVE...
If it's a Western Digital Drive go to their website and get their Drive Utility tool and run it on the drive...
If it's a Maxtor go get Powermax from their site and run it on the drive...
Do same for any other mfg drive i.e. Seagate, IBM or whatever...
THEN if it passes the tests with no errors use the drive to reload your OS again...THIS TIME load your drivers one at a time, same with your software...Do a system restore point prior to each load...this way you can easily undo whatever fails if anything...
Hope that helps!
Cheers!! 8)

DMI pool data clicks at K8N neo2

I have neo2 mainboard
I have updated the bios to 1.8 version (the former was 1.5)
now when I restart the computer a "verifying DMI pool data" message appears which is followed by several 'clicks'
what is it and how can I silence those clicks?

Hi! From where do these "clicks" come? I have the Neo2 and Bios V 1.8 and I get clicky' wid' it too... Mine seem to be coming from the drives, like an old school floppy seek sound, try disabling boot-up floppy seek and listen to the results...

Bios issues with k8n neo2, turn of memory test, and dmi pool data

Hey guys.
I recently flashed my bios to the 1.9's for the K8n neo2 running in my main machine.
Everything went ok for the most part, though i had some issues with boot record, and boot.cfg file. That stuff is all worked out now.
However, with this bios, I constantly get the extended memory test, on my 2 gigs of ram. The old bios i had, 1.4's, didnt do that. Is there an option to turn that off? I cant seem to find it any where?
My 2nd question is this, after this bios upgrade, my verifying dmi pool data takes longer then it used to, if it even did it before, im not sure, because my boot sequence was much faster.
How can I get rid of the "verifying dmi pool data" or speed it up?
Thanks guys

Tried to used the Bios 1c by Syar's. His bios is nice and easy. Maybe bould solve your problem.BTW do used liveupdate to flashed your Bios or is it manual? Stay away from using liveupdate as it causing a lot problems. Manual is the best way. Refer to my sig for the manual flashing. Here's the location of the files for the Bios 1C. Gd luck.
https://forum-en.msi.com/index.php?topic=59711.0
P/S: Create your own rig with details including the PSU and Bios revision and put in your signatures so others can help you.

Verifying DMI Data Pool

I have a ms-6533 motherboard (barebone system) and when i try to boot up the system using windows/me & maxtor harddrive, the systems hangs at "verifying dmi data pool ".
Please help :]

jan71942
New Member
Registration Date: 01-03-2003
Posts: 1
Verifying DMI Data Pool
I have a ms-6533 motherboard (barebone system) and when i try to boot up the system using windows/me & maxtor harddrive, the systems hangs at "verifying dmi data pool ".
Please help :]
There's not a lot of info to work with here. But here goes;
First I would recomend opening the case and checking that all cables are where they belong (check the Manual) and that they are well seated. You might want to remove then replace each end of each cable (one at a time) while you're there.
You might also turn on the power and check if all the fans are running and if the hard drive spins up.
Try booting up.
Secondly, try reseating the Memory and CPU. (again, check the manual)
Try booting up.
Third, clear the CMOS (manual)
Try booting up.
Fourth, turn on the power, hold down the 'Delete' key to enter the BIOS, go to 'Load Fail Safe Defaults'. At this point your system should ask you if you are shure you want to do this. Click 'yes'. Hit 'F10' to save your change then eigther the 'y' or 'Enter' key depending on your bios.
System should reboot on its own at this point.
You can download your manual at: http://download.msi.com.tw/support/mnu_exe/mbd_mnu/E6533v1.0.exe
Hope this helps.

Face Time stuck in verifying ....running Mavericks 10.9.5

Hi, My macbook early 2009 running 10.9.5 Mavricks is unable to run Face Time. After I enter my apple id & password, it gets stuck in Verifying....mode & after a while it pretends I need to log in from scartch.......please help!
JK

Please read this whole message before doing anything.
This procedure is a test, not a solution. Don’t be disappointed when you find that nothing has changed after you complete it.
Step 1
The purpose of this step is to determine whether the problem is localized to your user account.
Enable guest logins* and log in as Guest. Don't use the Safari-only “Guest User” login created by “Find My Mac.”
While logged in as Guest, you won’t have access to any of your documents or settings. Applications will behave as if you were running them for the first time. Don’t be alarmed by this behavior; it’s normal. If you need any passwords or other personal data in order to complete the test, memorize, print, or write them down before you begin.
Test while logged in as Guest. Don't post any more log extracts; just test. Same problem?
After testing, log out of the guest account and, in your own account, disable it if you wish. Any files you created in the guest account will be deleted automatically when you log out of it.
*Note: If you’ve activated “Find My Mac” or FileVault, then you can’t enable the Guest account. The “Guest User” login created by “Find My Mac” is not the same. Create a new account in which to test, and delete it, including its home folder, after testing.
Step 2
The purpose of this step is to determine whether the problem is caused by third-party system modifications that load automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Please take this step regardless of the results of Step 1.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output and Wi-Fi on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually log in automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of Steps 1 and 2.

My iPad 2 is stuck in verify update after updating to 8.1.3. Tried pushing buttons and holding. No luck

My iPad 2 is stuck in verify update after updating to 8.1.3. Tried pushing buttons and holding. No luck

How many times did you try the reset? Sometimes, it can take more than one reset, especially with these kinds of issues. Try multiple times. Note that you need to hold both buttons until the Apple logo appears on the screen. This can sometimes take 15-30 seconds.
Device Reset (won't affect settings/data/music/apps/etc)
1. Press and hold (& continue to hold) BOTH the Sleep/Wake button & the Home button.
2. Continue to hold BOTH (ignoring any other messages that may show) until you see the Apple logo on the screen.
3. Release BOTH buttons when you see the Apple logo and allow the device to boot normally.

Install Tiger gets stuck at "Verifying volume", Disk Utility not working

Hi there,
I am trying to upgrade to Tiger from OS10.3.9. I have repaired the disk permissions. Each time I try to install Tiger, it gets stuck at "Verifying Disk Volume". I then booted up from the Tiger DVD and ran Disk Utility from the DVD. Now First Aid is continually trying to repair the disk, and what appears over and over again is:
Rechecking volume.
Checking HFS Plus volume
Checking Extents Overflow file.
Checking Catalog file.
Incorrect number of thread records
Checking multi-linked files.
Checking Catalog hierarchy.
Checking volume bitmap.
Checking Volume information.
Repairing Volume.
Rechecking volume.
Checking HFS Plus volume
Checking Extents Overflow file.
Checking Catalog file.
Incorrect number of thread records
Checking multi-linked files.
Checking Catalog hierarchy.
Checking volume bitmap.
Checking Volume information.
Repairing Volume.
etc...
i don't know what to do about this. I do have two hard drives installed on my computer. The one I am trying to install on is a 74.5 GB ST380021A. The other is a 38.3 Maxtor 6E040L0.
It would be great to know if anyone has advice on this. Thanks so much!
clara

Hi there,
I am trying to upgrade to Tiger from OS10.3.9. I have
repaired the disk permissions. Each time I try to
install Tiger, it gets stuck at "Verifying Disk
Volume". I then booted up from the Tiger DVD and ran
Disk Utility from the DVD. Now First Aid is
continually trying to repair the disk, and what
appears over and over again is:
Rechecking volume.
Checking HFS Plus volume
Checking Extents Overflow file.
Checking Catalog file.
Incorrect number of thread records
Checking multi-linked files.
Checking Catalog hierarchy.
Checking volume bitmap.
Checking Volume information.
Repairing Volume.
Rechecking volume.
Checking HFS Plus volume
Checking Extents Overflow file.
Checking Catalog file.
Incorrect number of thread records
Checking multi-linked files.
Checking Catalog hierarchy.
Checking volume bitmap.
Checking Volume information.
Repairing Volume.
etc...
i don't know what to do about this. I do have two
hard drives installed on my computer. The one I am
trying to install on is a 74.5 GB ST380021A. The
other is a 38.3 Maxtor 6E040L0.
It would be great to know if anyone has advice on
this. Thanks so much!
clara
hai clara,
the issue is coz the drive on which ur trying to install has some issues .
please goto the article http://docs.info.apple.com/article.html?artnum=13628
in most of the cases u would try some third party disk utility like disk warrior and noton disk utility to repair the disk .
then u need to run disk utility from the TIGER disk .
follow the article
http://docs.info.apple.com/article.html?artnum=106214
to repair the disc .
or else u can back up the data on ur HDD and then u need to do an erase and install of TIGER

Cannot sync or backup properly. Stuck on "verifying" in iTunes

When I'm trying to sync with my PC, the iTunes status is stuck on "Verifying [iPhone name]". It won't go past that so I am unable to sync or backup properly. When I try to restore from backup, all the backup are corrupted or something, and I had to do a full reset. Lost everything but the contacts. However, the same problem is happening again. I haven't reset it again because I don't think it will solve the problem.
This problem has been happening since I moved to a new computer from Windows Vista 32bit to a Windows 7 64bit. I tried to move all the relevant iTunes data. It apparently worked correctly at first, but now the syncing has fully stopped.

Good stuff...
For any other applications you may have trouble with... running in Vista Compatibility mode is done by locating the programs installation directory and then locating the .exe file in your system...then right click on that .exe and a window will appear...goto the compatibility tab and then choose either XP or Vista as the compatibility mode...
See this link for visual help...
http://www.howtogeek.com/howto/windows-vista/using-windows-vista-compatibility-m ode/

Apple TV .. verify my account data on my computer before purchase.

Why does Apple TV need me to verify my account data on my iTunes account before purchase? I don't have to do this with iPad or iphone. It is a nuisance, especially if my wife is making the movie decision since she doesn't like to go into my laptop data to enter my credit card info.

The iTunes music store makes you verify your account any time you are connecting from a new device with a new account. It is to prevent credit card fraud. As long as you are not chaning the account used you should only have to do this once when you first use a new device.

Pooling data from an XML file to another XML file using File Adapter

Hi,
I am trying to Pool data from an XML file to another XML file using File Adapter. I have added "Target Namespace" in both the XML and XSD.The problem is "At the destination given in the FileAdapter" only a blank XML file is created and it doesnot have any data.
Kindly suggest me some methods
Thanks in Advance.

Ok here is a solution with external tables.
SQL> CREATE DIRECTORY my_xml_dir AS 'E:\oracle\Log_files\UTL_AKIVATST'
2 /
Directory created.
SQL> DROP TABLE my_xml_et
2 /
Table dropped.
SQL> CREATE TABLE my_xml_et
2 ( EMPNO NUMBER,
3 EMPNAME VARCHAR2(10),
4 JOB VARCHAR2(10),
5 HIREDATE DATE,
6 SAL NUMBER
7 )
8 ORGANIZATION EXTERNAL
9 (
10 TYPE ORACLE_LOADER
11 DEFAULT DIRECTORY my_xml_dir
12 ACCESS PARAMETERS
13 (
14 records delimited by "</EMP>"
15 badfile my_xml_dir:'empxt%a_%p.bad'
16 logfile my_xml_dir:'empxt%a_%p.log'
17 FIELDS
18 (
19 filler char(2000) terminated by "<EMP>",
20 EMPNO char(2000) enclosed by "<EMPNO>" and "</EMPNO>",
21 EMPNAME char(2000) enclosed by "<ENAME>" and "</ENAME>",
22 JOB char(2000) enclosed by "<JOB>" and "</JOB>",
23 HIREDATE char(2000) enclosed by "<HIREDATE>" and "</HIREDATE>",
24 SAL char(2000) enclosed by "<SAL>" and "</SAL>"
25 )
26 )
27 LOCATION ('emp.xml')
28 )
29 PARALLEL
30 REJECT LIMIT UNLIMITED
31 /
Table created.
SQL> SELECT * FROM my_xml_et
2 /
EMPNO EMPNAME JOB HIREDATE SAL
7369 SMITH CLERK 17-DEC-80 800
7499 ALLEN SALESMAN 20-FEB-81 1600
This is the XML file i used emp.xml
<EMPLOYEES>
<EMP>
<EMPNO>7369</EMPNO>
<ENAME>SMITH</ENAME>
<JOB>CLERK</JOB>
<HIREDATE>17-DEC-80</HIREDATE>
<SAL>800</SAL>
</EMP>
<EMP>
<EMPNO>7499</EMPNO>
<ENAME>ALLEN</ENAME>
<JOB>SALESMAN</JOB>
<HIREDATE>20-FEB-81</HIREDATE>
<SAL>1600</SAL>
<COMM>300</COMM>
</EMP>
</EMPLOYEES>
Use this external table to insert into your table.
Thanks,
Karthick.

Time machine stuck on verifying backup

My time capsule and tiem machine are very very slow and keep getting stuck on verifying backup, or preparing backup, and then says cannot complete the backup since the backup disk image MacBook Pro.sparsebundle could not be accessed (error -1).

Try here > http://pondini.org/TM/TCP2.html
From here > http://pondini.org/TM/Time_Capsule.html
Also... See this discussion...
https://discussions.apple.com/thread/4944252?tstart=0

975x stuck at "Verifying DMI Pool Data"

Similar Messages

Maybe you are looking for