A88XI AC RAM settings help!
Hi Guys,
I'm a complete noob when it comes to PC building, so go easy lol
I've built a budget gaming PC using the A88XI AC motherboard a A10 7850 and 8GB of Corsair Vengence 2133Mhz RAM.
The system works ok, but the RAM speeds reported are only showing as 667Mhz or 1066Mhz depending on where I look.
But I don't really understand.
RAM specs are: CMZ8GX3M2A2133C11R - 8GB (2x4GB) Corsair DDR3 Vengeance Racing Red, PC3-17066 (2133), Non-ECC Unbuffered, CAS 11-11-11-27, XMP, 1.5V
Could anyone guide me through the BIOS settings to setup the RAM please?
Your memory has native 1333 chips on it and in the memory profile, one of the profiles will be an XMP or AMP profile which allows an invoked overclock of 2133.
By default the memory will be at 1333 (667) when the BIOS first detects it.
You need to go into your BIOS and set your memory to apply XMP or AMP depending on which one your memory has.
You can download and use CPUZ. In the SPD tab, all the memory programmed JEDEC profiles will be visible and it will also show if its XMP or AMP.
Suggest you go onto the MSI main site and download the full user manual for your board, Then go to the BIOS section of the manual and see where to access the memory control. You dont have to use the XMP settings, you can also set the memory manually according to the JEDEC specs that are reflected in the SPD tab.
Similar Messages
-
What should Ram settings be for FCP 6 doing a slideshow with JPEGS ?
Hi all,
I am doing a Ken Burns effect slideshow in FCP6 that is using JPEGS only.
I have the 24" intel imac 2.4 gig with 4 gigs of Ram installed.
I am wondering what my ram settings in FCP should be.
there are 4 boxes you can fiddle with the numbers.
first two have sliders and go from 0 to 100%
"memory usage"
and also still cache...
what should I be setting these to?
thanks in advance!
I ask because my system bogs right down with only a few layers and effects in place.
what should my sequence settings be as well when working only with JPEG?
I normally edit in easy DV NTSC....Thanks guys.
I have found that I cannot resize and get a clean movement here in FCP.
I tried the cutting approach jim and that at least got me through the placement of the pics to the song and then I started the motions. I also checked and then unchecked the shadow once I had it set where I wanted. I like to work through each pic from start to finish so i know exactly where I am at each night when I go to bed and then where I start again the next evening after my day job!
haha
but yes unchecking the shadows and feathered edges definately bought me some more time before render.
I appreciate all the helpful advise here. You guys pour so much knowledge out there for us and mostly without even much thanks to you in return.
One question I would still have now that I have fiddled around with all my settings....
would anyone have the time and the knowledge to help me figure out what the "proper" settings should be for my setup for editing regular sd dv ntsc footage?
or when I click easy setup dv ntsc does it configure my system for optimal settings each time?
ie what should my ram settings be?
thanks in advance.
see sig for setup. -
Does anyboy know how to do setting on NV RAM settings on sunblade 150 system
Hello
Does anyboy know how to do setting on NV RAM settings on sunblade 150 system
regars
kamranHi 82c37566-552c-40e9-b16b-3effc555d259, the best place to search for questions like this one is Oracle Technology Network. If you have any question about Cloud and partnering with Oracle we will be more than glad to help! Thank you!
-
K9n2 diamond Ram timings help.
So I've got a k9n2 diamond, and GeIL Green Series 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500). The problem that I'm having is that after 2 weeks of owning the ram i realized it was running at 800mhz and not its advertised 1066mhz. So I went into the bios and set it to 1066, and upon the next boot it told me i had bad ram settings and I needed to go back and fix them. I assume its not working because I didn't set the recommended manufacturer timing which is 6-6-6-18. And I believe the ram is 2t because the system wont post at all if set to 1t. So my question is: How do I set the timings I assume in advance dram settings? although there are a lot of options in there which i don't understand. Oh and I'm also running the latest bios 2.61
Link to the ram: http://www.newegg.com/Product/Product.aspx?Item=N82E16820144347
Any help would be appreciated.Actually I notice the difference in Battlefield bad company 2. You see I went from these: http://www.newegg.com/Product/Product.aspx?Item=N82E16820220334 (Patriot Viper 4GB (2 x 2GB) 240-Pin DDR2 SDRAM DDR2 1066 (PC2 8500)) if you don't trust the link. I switched because I kinda destroyed 3/4 other sticks of the Patriot memory I had taking off the heat spreaders...
Edit: So you're saying that I can get it to 1066 through adjusting the timings right? If so how? -
My ipod screen wont slide to unlock and i have just reset it to factory settings, help!
my ipod screen wont slide to unlock and i have just reset it to factory settings, help!
Seems like a hardware problem. An appointment at the Genius Bar of an Apple store is in order.
-
I phone 5c settings help.
help!i phone 5c settings help. upon opening phone shows enlarged keypad for my pass code, but is difficult to type on. how to get my numbers and home screen back to normal.
On the Home screen, double-tap with three fingers to exit zoom.
Then, after you have entered your Passcode...
go to Settings > General > Accessibility and make sure Zoom is turned Off.
More Info here > http://support.apple.com/kb/ts3129 -
I have OS 10.4.11 with only 512 MB of memory and am trying to download Snow Leopard 10.6.3, it requires 1GB ram please help.
See Here for Installing RAM...
MacBook http://support.apple.com/kb/HT1651
Be sure to get the correct matching RAM for your Computer -
Your call cannot be connected pls. check your phone settings help plsss
your call cannot be connected pls. check your phone settings help plsss
mhayo wrote:
your call cannot be connected pls. check your phone settings help plsss
Check the Telephone Number you are calling...
Contact your Carrier.
Also...
Try This...
Close All Open Apps... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430 -
I have built many systems but have never over clocked so I need to ask you experts a few things. I have the P965 Platinum with a QX6700 quad core on it. My ram is Corsair XMS twin2x2048-6400C4D. Do I need to set the ram settings in the bios for this ram? I found it is to be set at 4-4-4-12 at 2.1 volts at 800 Mhz. http://www.corsairmemory.com/corsair/products/specs/TWIN2X2048-6400C4D.pdf
Should I set this and anything else in my Bios to make this thing run at top preformance? I would no mind OCing a little as long as it's stable. please advise as I have never done this. ThanksI wouldn't mess with any manual timming on this board until MSI fixes it, because it does not set the timings correctly and you would end up with an unstable system.
If your memory is detected at 4-4-4-12 be happy, if it's set to 5-4-4-12 be happy also, if it's set in 5-5-5-15, then, try to do something about it, other than that there is little to no difference in setting memory lower than that and chances are you won't be able to manually because the BIOS does not set timings correctly when in manual mode.
If you have the chance, disable the FULL SCREEN LOGO and then, press pause key when the computer starts, you should be able to read the timings the BIOS had already set to auto. -
Have 2009 iMac, 2GB of RAM, with ML, see beach ball alot lately, any solutions? More RAM? Help!
Agree titally with th great posters so far.
So we know more about it...
At the Apple Icon at top left>About this Mac, then click on More Info, then click on Hardware> and report this upto but not including the Serial#...
Hardware Overview:
Model Name: iMac
Model Identifier: iMac7,1
Processor Name: Intel Core 2 Duo
Processor Speed: 2.4 GHz
Number Of Processors: 1
Total Number Of Cores: 2
L2 Cache: 4 MB
Memory: 6 GB
Bus Speed: 800 MHz
Boot ROM Version: IM71.007A.B03
SMC Version (system): 1.21f4 -
Hi,
I recently upgraded my system to a KT4 ultra, athlon 2200+XP, 512MB Crucial 2100 DDRAM and an MSI GF4 Ti4600.
Now its running ok, but I think its running a tad under par. Its benching about 10900 on 3DMark 2001. Which aint the best.
I was wondering about changing the RAM settings in BIOS. Would they have much of effect?
Also what about flashing the BIOS, with version 1.1? I'm very wary about doing that because the last couple of times I flashed a bios it screwed the motherboard up royally. Is it worth the risk?
TaHi,
You may try "Load High Performance Default" in the BIOS. If it works, good, you should get few extra marks by some margin. If it caused instability to the system, don't force it, revert to BIOS Setup Default.
The effect of those RAM settings can only be seen by benchmarks. Normal usage, you can hardly feel any difference.
For BIOS, "if it aint broke, don't fix it". Most BIOS updates do not meant to improve performance, but for bug fix and to support new hardware. Read the BIOS update info you'll know what has been fixed/updated. -
Does adding RAM really help performance?
My iMac 1.8 GHz G5 is about two years old and starting to run slowly. Could it be the 10,000 photos and 6,000 songs? I've started using my MacBook for most work and my iMac for most play (i.e. media).
Does adding RAM really help performance? I've only got one 512 MB chip.
Thanks for any help.Hello,
Yes, adding more memory can make a huge performance improvement.
I've owned two iMac G5 systems. And, in both cases, I noticed a huge performance improvement jumping to 1 GB of RAM. And, while not huge, I noticed even better performance going from 1 GB to 2 GB of RAM.
512 MB is minimal, and adequate. But, more memory makes OS X run considerably better.
I hope this helps.
Let us know if you have other questions.
P.S., if you'd like, go ahead and click the "Helpful" or "Solved" buttons on any of the posts / replies above if you feel they were helpful or adequately answered your question. -
Quick Help w/ Ram Settings
Hey I got a question for you.
I have a MSI Neo2 Platinum, with an Athlon 64 3500.
I have 2x512 DDR500 PC4000 sticks of ram.
My question is, I always see people typing their settings in (ie: 3.0-2-2-6) I've tried to read up, but I just dont get it. Anyhow, what should my settings be at? All I do is play video games on this computer, and all I want out of my ram is what I paid for which is the ddr500 and pc4000 specs. Any suggestions?Quote
Originally posted by Krondo.wg
Hey I got a question for you.
My question is, I always see people typing their settings in (ie: 3.0-2-2-6) I've tried to read up, but I just dont get it. Anyhow, what should my settings be at? All I do is play video games on this computer, and all I want out of my ram is what I paid for which is the ddr500 and pc4000 specs. Any suggestions?
My advice for what its worth - dont sweat it man!
its usually not worth much in terms of performance - just leave em set at Auto -
Photomerge settings help, performance settings?
Having issues using photomerge with the latest version of Photoshop. I have about 120 images that are 16 mp RAW. What should I have my Photoshop Performance settings at? Cache Levels and Cache tile size? Also how much ram should I use?
My system settings are 18 gig of RAM, Core i7 920 like 4 different hard drives, Nvidia geforce 570 HD
I was using windows 8, now trying 7 but they still both crash and or take hours with no results.I suggest Cache Levels = 6 as this is shown to speed Photomerge up vs. a setting of 4..
With 18 GB of RAM in your system I'd suggest settiing Photoshop to use 90%. But 18 GB of RAM is going to be WAY too little for 120 images of 16 megapixels each. 48 GB or more (possibly much more) would be helpful for that big a stitch.
Make sure you have a HUGE amount of free scratch space available - I mean at least 400 GB or more. Scour your system for Photoshop temp files left behind from your past failed runs.
Also, what's your ultimate goal in image size? Do you really need to stitch the images together after conversion to the full 18 MP size? Maybe you should set Camera Raw to deliver conversions at a smaller size to reduce system resource usage.
-Noel -
AE CS5 Preference Settings Help!
Hi Guys,
I'm working with CS5 now. Can anyone help me configure the best settings in After Effects to get the most out of my PC and the software please?
PC configuration listed below. I have listed the current settings I have now for AE. Please advise what I should change.
Thank you in advance.
Regards.
Mark
My current preference:
General: Levels of Undo: 99 / Path Point Size = 5 pixels. The rest of the settings are default.
Previews: Adaptive Resolution Limit: 1/4. Enable Open GL is NOT checked. Zoom Quality=Faster, Color management=More accurate exept RAM preview,
Alternate RAM preview= 5 frames, audio preview=00:30:00
Display: Motion Path=selected is No More Than 00:15:00, nothing else is checked below
Import: Still Footage: Lenght of comp is selected at 00:01:00, Seq. footage=30 frames
Output, Grids & Guides and Lables are all default
Media & Disk Cache: Disk Cache=Enable Disk Cache is NOT checked, XMP Metadata=both are checked
Video Preview: PC Monitor only
Appearance: Default for checks, brightness=darkest setting, Affects label colors NOT checked
Auto Save: Automatically.... is checked, save every 10 min., Max project = 99
Memory & Multiprocessing: Shows Installed RAM: 16 GM, RAM reserved for other applications: 3 GB, RAM available for: AE, PP, En, Bridge: 13 GB,
After Effects Multiprocessing: Render Multiple Frames Simultaneously is NOT checked
Audio Hardware: MOTU
Audio Output: MOTU 1-2
• DAW I:
VisionDAW 4U 8-Core Xeon Workstation
2 Intel QUAD-Core Xeon 5365-3.0GHz, 8MB, 1333MHz Processors
16GB 667MHz Fully Buffered Server Memory Modules (2x2GB)
Microsoft® Windows® XP Professional x64 Edition
Microsoft® Windows® Windows 7 x64
WDC 250GB, Ultra ATA100, 7200 rpm, 8MG Buffer Main OS HD
2 WWDC 750GB, SATA II, 7200 RPM, 16MB Buffer HD (Raid 0)
2 WDC 750GB, SATA II, 7200 rpm, 16MG Buffer HD (Samples)
2 WDC 1TB Enterprise Class, SATA II, 7200 RPM, 32MB Buffer Hard Drive
MOTU 24 I/O (main) / MOTU 2408mk3 (slave)
Plexor PX-800A 18X Dbl. Layer DVD+/-RW Optical Drive
Buffalo BuRay Drive (External) BR-816SU2
Front Panel USB Acess
Integrated FireWire (1394a) interface
Thermaltake Toughpower 850W Power Supply
3xUAD1 Universal Audio Cards
NVIDIA QUADRO FX 1800 / Memory 768 MB GDDR3
CUDA Parallel Processor Cores / 64
Maximum Display Resolution Digital @60Hz = 2560x1600
Memory Interface 192Bit
Memory Bandwidth (GB/sec) / 38.4 GB/sec
PCI-Express, DUAL-Link DVI 1
Digital Outputs 3 (2 out of 3 active at a time)
Dual 25.5" Samsung 2693HM LCD HD MonitorsHello Todd,
Thanks for replying. My main concern is for the 3 preferences that are in bold. I was hoping that you (or someone) could suggest the best
settings for these three preferences based upon my PC specs.
If this machine was yours, how would you tweak these three preferences?
Maybe you are looking for
-
SDK development for SAP BusinessObjects Explorer Accelerated version
Hi all, in one of our project we need to use the engine of Explorer Accelerated an SDK application. Is it possible or does exists sdk libraries for using only the search component of Explorer? What we need is something that give to Explorer box our s
-
My i tunes on a new i-mac doesn't read my old i phone 3gs? what can i do?
help
-
CFP Channel browsing gives problem in exe
We have configuration screen in which user can assign CFP channels for specific data acquisition. For browse purpose we are using "FieldPoint IO Point" control. In VI everything works fine. But if I create Exe, if I select "bwowse" option then brows
-
Hi Gurus, Could you please let me know the end of life and support for following Oracle software. Oracle 10g r2 Database 10.2.0.3 Oracle 10g Application server 10g r2 Oracle 10g r2 Client Oracle 10g r2 Forms & reports developer tool set 10g r2 Regard
-
Just video no audio from Compressor 4 to DVD PRO-What's wrong
I have successfully sent my project from FCP7 to Compressor 4 and compressed it on Best Quality DVD 90 minutes. Once I bring in the file as an Asset in DVD PRO I just get the video part of the compression no audio. I also get a incompatible file pop