ACE30 - Accessing the ACE Applicance Device Manager

Hi...
I've got basic connectivty to our ACE30 module and when I try connecting to the management IP address (attached to the Admin context), I see a very basic GUI which only lists the CSM to ACE config conversion tool.  I don't see a GUI as detailed in the document:
http://www.cisco.com/en/US/docs/app_ntwk_services/data_center_app_services/ace_appliances/vA1_7_/configuration/device_manager/guide/UG_over.html#wp1072950
How do I get the ACE Applicance Device Manager GUI working so that I can then configure real servers, serverfarms etc rather than via the GUI?
Having read through copious amount of documentation I can't seem to find a refrence that would help here.  This should be a fairly straight forward exercise - do I need to install some other software to get the full fledged GUI working?
thanks
Sheldon

Only the ACE 4710 appliances have the GUI.   If you are looking for a GUI for the ACE30 module you will need to use Cisco Application Network Manager (ANM)   It will provide the GUI for the ACE30 to be able to configure it.   As you have seen, only the conversion tool is available on the module.

Similar Messages

  • Error (-6722) occurred while trying to access the Apple Wireless device

    I receive the following error when I press 'manual setup' or 'continue' from within the airport utility:
    "An error ocurred while trying to access the Apple wireless device. Make sure your network connection is valid and try again
    Error -6722"
    Everything is working on the Airport express but I can't run the utility. Should I hazard a reset of the device to factory settings?

    Aaaaaaand as I was writing that, I managed to fix it. Not sure how exactly. The variables that were used that worked:
    On windows, running AU 5.5.2, right clicking upload firmware in the device list, choosing other, selecting a random firmware other than 7.3 (I think i ended up using 7.4.2) and clicking upload. Instead of trying to communicate with the APExpress, it directly uploaded the firmware and then it restarted, I got a crazy amber blink cycle I have never seen before (Three fast long blinks, and the three short fast blinks, repeat). Then it restarted and it was back to normal. Woohoo! There goes 5 hours of my life.

  • Unable to access the data from Data Management Gateway: Query timeout expired

    Hi,
    Since 2-3 days the data refresh is failing on our PowerBI site. I checked below:
    1. The gateway is in running status.
    2. Data source is also in ready status and test connection worked fine too.
    3. Below is the error in System Health -
    Failed to refresh the data source. An internal service error has occurred. Retry the operation at a later time. If the problem persists, contact Microsoft support for further assistance.        
    Error code: 4025
    4. Below is the error in Event Viewer.
    Unable to access the data from Data Management Gateway: Query timeout expired. Please check 1) whether the data source is available 2) whether the gateway on-premises service is running using Windows Event Logs.
    5. This is the correlational id for latest refresh failure
    is
    f9030dd8-af4c-4225-8674-50ce85a770d0
    6.
    Refresh History error is –
    Errors in the high-level relational engine. The following exception occurred while the managed IDataReader interface was being used: The operation has timed out. Errors in the high-level relational engine. The following exception occurred while the
    managed IDataReader interface was being used: Query timeout expired. 
    Any idea what could have went wrong suddenly, everything was working fine from last 1 month.
    Thanks,
    Richa

    Never mind, figured out there was a lock on SQL table which caused all the problems. Once I released the lock it PowerPivot refresh started working fine.
    Thanks.

  • Can no longer access the Canon Remote UI Management Mode (Portal) (on my Desktop Computer)

    I set up access to the Canon Remote UI Management Mode (Portal) using my IPv4 address so that I could make changes to the settings of my imageCLASS MF6160dw directly from my Desktop Computer. That has worked flawlessly for almost 3 months. Then, all of a sudden 3 days ago, I started getting this message: This page can't be displayed I have not added nor removed any equipment or software to my Desktop Computer. I also reconfirmed that my IPv4 address was correct.And I try to access the "Portal" numerous times at different times of the day & on different days. My Desktop Computer is a Dell XPS 8700 Special Edition running Windows Pro 8.1 (64-BIT) How can I regain access to the "Portal"?

    I never got a reply from anyone.
    But for those who viewed this thread & may also have this problem, I finally figured out that the IP Address had actually CHANGED.
    How & why it changed, I do not know.
    But, the last 2 digits of .15 changed to .2
    I can now access the Canon Remote UI Management Mode (Portal) by using the CHANGED IP Address.
    Hope this helps someone.

  • An error occurred while trying to access the Apple Wireless Device

    Hello All;
    I just bought an Airport Extreme Base Station today and am all ready having problems. I am running a PC. I connected a Motorola DSL model to the Airport's QAN port and then I connected the computer to one of the Ethernet ports. When I first loaded the software that came with it, things worked perfectly and I was able to connect to the internet. Then, when I opened up the configuration file, and try to enter the configuration manually, I receive the error ... "An error occurred trying to access the Apple Wireless Device. Make sure your network connection is valid and try again". When I try to open the Manual setup I get that error. Also why are the "settings" always grayed out ? I am connected ot the Internet but can't understand why I can't do a manual setup or change any of the settings. I reset my passwords and need to change them again but am unable to do that. Thanks for any help and advice you can give me.
    Tim

    I am about to return this unit to the store I bought it at. I keep getting an error 6753 whenever I try to do any kind of configuration. Most of the configuration options are grayed out in the setup utility anyway. There is a ton of stuff about this problem on the internet. There are a few solutions offered like modify the tcp/ip properties but I sure can't figure out what they're talking about. Not everyone who buys this is going to be tech savvy.
    I'll call tech Support tonite and if they can't offer a permanent soultion, I'm returning the Airport Extreme and separate dsl modem tomorrow and getting a wireless dsl router specifically designed for the PC.
    Tim

  • In my laptop internal bluetooth is disabled by the windows frm device manager, hw can I enable it ?

    I am using hp probook 4530s comes with windows 7 home premium. In my laptop internal bluetooth is disabled by the windows from device manager, how can I enable it ? Please help...... The error is: Windows has stopped this device because it has reported problems. (Code 43)

    I too am faced with the same problem. What I have done. 1) Installed latest firmware2) Installed lated Wifi adapter driver.3) Installed HP Connection manager4) Installed HP Support Assistant5) Uninstalled, Removed aand Deleted current Generic Bluetooth driver and reinstalled.6) Managed the Adapter settings to Enable Bluetooth.7) Searched the whole insterwebs for a fix that works for me and found nothing.8) Found a gun range that will allow me to use this laptop as a target. Please save this poor laptop from being a target at a gun range. HP FIX THIS PROBLEM PLEASE!

  • Where is the network - workspace - device management's log? what is the name of the network - workspace - device's service?

    Hi guys!
      I want to know where can I set up the network -> workspace -> device management's log and get the log and what is the name of the network -> workspace -> device's service? Thank you for your answers.

    Forget hotel technical support. All they'll do is refer you to a toll free number to the other side of the globe where somebody will tell you to click a Start button, or something. It's an utter waste of time.
    What you describe is a "captive network" and yes, the need to authenticate each and every time you shut down your Mac or let it sleep is a common annoyance. The IT idiots that sold the Internet package to the hotel chain is long gone. Complain to whomever you can find, and perhaps one day they'll address their own incompetence. Until then keep your Mac connected, don't shut it down or let it sleep. Even then you may find yourself logged out from time to time, which you might not even become aware of until web pages stop loading. You can do nothing to fix it, other than to refuse to frequent that hotel chain. Be sure to tell them why.

  • Which apple id's countries are allowed to access the itunes u course manager?

    If I try to access the ITunes U Course Manager I get a message about my country apple id is not allowed. Which countries are?

    Hello patrizio_p
    Check out the article below to see what content is available for different countries. If you are able to get iTunes U in your countries you should be able to access the iTunes U Course Manager.
    iTunes Store: Which types of items can I buy in my country?
    http://support.apple.com/kb/ts3599
    Regards,
    -Norm G.

  • ACE 4710 Device Manager Gives Blank Screen

    Hi Guys,
    Wish somebody could share his/her experience on this.
    I have a problem with ACE4710 Device Manager that after entering username and password, it will appear just a blank screen. And it happen also to the FT peer.
    I know that the workaround is to reload the ACE (as it happened one time before) but I wish somebody could share a better or probably permanent solution to this problem.
    Thank you in advance guys.
    Tomy.

    CSCsv95366: Device Manager displays a blank page after login
    Upgrade to A3(2.2) or beyond.
    Gilles.

  • ACE-4710 : Device Manager on Primary ACE cannot authenticate

    Hi,
    In a cluster of redundant ACE-4710, version A5(1.2), the graphical Device Manager on the primary ACE cannot authenticate users. An error message is displayed :
    The strange thing is that the standby ACE Device Manager work correctly. Moreover, both ACE are perfectly synchronized :
    CH01AC03/P-115-A# sh ft group summary
    FT Group                     : 14
    Configured Status            : in-service
    Maintenance mode             : MAINT_MODE_OFF
    My State                     : FSM_FT_STATE_ACTIVE
    My Config Priority           : 200
    My Net Priority              : 200
    My Preempt                   : Enabled
    Peer State                   : FSM_FT_STATE_STANDBY_HOT
    Peer Config Priority         : 150
    Peer Net Priority            : 150
    Peer Preempt                 : Enabled
    Peer Id                      : 1
    No. of Contexts              : 1
    Here is the details on the ACE and DM version :
    CH01AC03/P-115-A# sh ver
    Cisco Application Control Software (ACSW)
    TAC support: http://www.cisco.com/tac
    Copyright (c) 1985-2012 by Cisco Systems, Inc. All rights reserved.
    The copyrights to certain works contained herein are owned by
    other third parties and are used and distributed under license.
    Some parts of this software are covered under the GNU Public
    License. A copy of the license is available at
    http://www.gnu.org/licenses/gpl.html.
    Software
      loader:    Version 0.95.1
      system:    Version A5(1.2) [build 3.0(0)A5(1.2) adbuild_19:38:58-2012/01/17_/auto/adbure_nightly4/renumber/rel_a5_1_2_throttle/REL_3_0_0_A5_1_2]
      system image file: (hd0,1)/c4710ace-t1k9-mz.A5_1_2.bin
      Device Manager version 5.1 (0) 20111215:1009
    What coud be the problem ?
    Thank you
    Yves

    Hello Yves,
    Try with the command "dm reload" in the Admin Context
    Cesar R
    ANS Team

  • My Ideapad U310 doesn't work and doesn't show me the webcamera in device manager.

    Hello everyone,
    I have a big problem on my Lenovo U310, my wecamera doesn't work, i don't manage to find neither in device manager and i've tried to reinstall all the drivers, even with recovery button but with zero results.
    Could enyone please give a hand with this?
    Solved!
    Go to Solution.

    Hi Tudor_ke,
    Welcome to Lenovo Community!
    I’m sorry to hear that the Webcam is not detecting in device manager even after re-installing the drivers as well as performing OKR (One Key Recovery) in your U310 Laptop, I suggest you to press Fn+Esc keys together and check if the webcam gets listed in Device manager, if the issue persists. I suggest contacting our Technical Support Team to get the details of the nearest Authorized Service Center to get the issue analyzed.
    Click here to open a link where you can select the country and get the exact contact support number. I’m sure they will be a great help.
    Do post us back for further queries.
    Best Regards
    Shiva Kumar
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • Error - 6753 "error accured while trying to access the apple wireless devic

    Hi I have an Airport Extreme with time capsule 1TB. It worked fine with all my win XP and Macs at home but suddenly it started with the message in the header. it pops up " An Error accurred while trying to access Apple wireless device. Make sure your network connection is valid and try again. Error -6753.
    What does it mean. I can access internet just fine and can print from the thing but can;t access my storage. Why is it happening? It all worked just fine before.
    your advice will be much appreciated

    Just a quick note: It says I have a macbook pro on my sigature. I do have one. I also connect a Dell XPS 600 (XP SP3), Dell 1420 laptop (Vista Ultimate), and an HP LaserJet 2420 (usually on the USB port, occasionally on the WAN ((RJ45))port. So far the airport has handled everything. I've had best results when setting it up from only the computer that uses the direct ethernet port. Add all the other stuff - wireless, USB - afterwards. Also, the Bonjour utility, which you can download from Apple's support site, is quite useful in setting up the printer.
    If you want to see what the IP address of the airport actually is, you can go to Start, Run, type CMD (brings up a dos window), then type "ipconfig" (no quotes) and you will see an IP address for "default gateway". That is the address of the airport, when you have to use the "Other" option. Similarly, the command "ipconfig /all" (no quotes) will give you the IP addresses of all the devices connected to the airport.
    OK, it wasn't such a short note.
    Bon Chance - dave

  • The properties in Device Manager says my vid. card is PCI!!!

    Of course it's AGP, why does it show up as PCI?

    I take it that it will say "PCI-bus 1, apparatus 0, function 0", or something alike ... It is supposed to be that way  )
    Hans

  • View-only access to Catalyst 2960/2960S device manager

    I have noticed that when I access the (Web-based) device manager on a Catalyst 2960 or 2960S switch, the authentication prompt (from within IE, at least) includes the phrase, "The server <switch-hostname> at level_15_or_view_access requires a username and password." This would seem to imply that it's possible to configure view-only (a.k.a. read-only) access to the device manager, which would be perfect for first-level support personnel (in our environment). I reviewed the information on how to configure local authentication for the Web server (leveraging "ip http authentication local" among other commands), but the examples are a bit too broad for me understand how to specifically (and only) allow someone coming in via HTTP(S) to gain read-only access to the device manager. (Command line access should be denied entirely for the view-only user, if possible, or at least limited to commands that can't modify the switch's configuration.) Assuming this is possible, could someone cite the command sequence required?
    Thanks,
    Mike

    Hi,a customer want a user which has view-only rights on his catalyst switches. I created a user whit privilige level 7.If you log into the CLI everything is fine. But by trying to log into the web page the system wants a level 15 user.Is their any possibility to grant the level 7 user "view-only" rights on the Catalyst Device Manager?Thanks.Thanks.
    Hi,
    Check out the below link for SDM for read only user configuration
    http://conft.com/en/US/docs/routers/access/cisco_router_and_security_device_manager/application/notes/SDMcli.pdf
    Hope to Help !!
    Ganesh.H
    Remember to rate the helpful post

  • Some odd warnings and messages for my Helix in the Lenovo Device Manager "Check Up" screen

    If I open up the Lenovo Solution Center software, and go to the Check Up tab and select Device Manager, it shows a warning that says "One or more devices have problems", and lists two drivers that show "Unknown device" with a status of "Not installed".
    There's no other information and I'm not sure what to make of this. Does anyone else have this issue? If I open up the Windows 8 Device Manager and expand all nodes in the tree, I don't see any devices with warning icons.
    Also if I go back to the Hardware Scan button in the Check Up tab, and run it, althought he scan passes, it shows a Warning for the SMART short self test, and notes that the test is "Not supported", with a result code of WHD01V000-WIVZ2I. Is this anything to be concerned about? Note that it's not a failure, but a non supported test. Does anyone else's Helix complete this test?

    I have the exact same problem with regard to 2 unknown devices not installed.  I got the message after first getting the Helix and running the updates.  I called Lenovo support and the tech could not figure it out and her response was "Well if is not causing any problems, I would not worry about it"  which sounds like an excuse to just get me off the line.  I was in a hurry to get somewhere and so did not push the issue.
    The message only says 2 divices not installed, but does not tell you which ones.  The tech said that if it was a real problem, the message would tell me what divices are not loaded.
    I have seen another post or two from people with the same issue but not suggested fixes.

Maybe you are looking for