ADSL modem D-Link DSL-G684T slow down my system

Hello!
I`m using Archlinux [core dump] with GNOME 2.20 and from yesterday I have got new modem-D-Link DSL-G684T.. When I plug Eth0 connector and internet is up, system is totaly slow!!! I try this on machine with Windows XP- Here work all fine. What is the problem? Some wrong settings? Is here some special setting for Linux machine?

This is my /etc/resolv.conf:
# Generated by dhcpcd for interface eth0
nameserver 192.168.1.1

Similar Messages

My DSL has slowed down over the last few months

Guys;
My DSL has slowed down over the last few months. I had the service that is up to 1.5 M and I used to get 1.2 ish on the verizon speed test, lately I've been getting between .9 and 1.0 at the most. I got the info from the speed test and here is a portion of that info:
------ Web100 Detailed Analysis ------
Client Receive Window detected at 1045440 bytes.
Cable modem/DSL/T1 link found.
Link set to Full Duplex mode
Information: throughput is limited by other network traffic.
Good network cable(s) found
Normal duplex operation found.
SHould I be concerned by the portion that I bolded and underlined?
Also, I just last night upgraded my service to the 1.1 to 3.0 service but I've not gotten a speed increase. Any suggestions?
Thanks

Here is a complete post of the information from the verizon speed test:
Analysis information:
Checking for Middleboxes . . . . . . . . . . . . . . . . . . Done
SendBufferSize set to [130680]
running 10s outbound test (client to server) . . . . . 471.01Kb/s
running 10s inbound test (server to client) . . . . . . 556.87kb/s
------ Client System Details ------
OS data: Name = Windows XP, Architecture = x86, Version = 5.1
Java data: Vendor = Sun Microsystems Inc., Version = 1.6.0_29
------ Web100 Detailed Analysis ------
Client Receive Window detected at 1045440 bytes.
Cable modem/DSL/T1 link found.
Link set to Full Duplex mode
Information: throughput is limited by other network traffic.
Good network cable(s) found
Normal duplex operation found.
Web100 reports the Round trip time = 1247.01 msec; the Packet size = 1322 Bytes; and
There were 14 packets retransmitted, 4 duplicate acks received, and 5 SACK blocks received
The connection stalled 1 times due to packet loss
The connection was idle 2.65 seconds (17.66%) of the time
This connection is sender limited 75.84% of the time.
This connection is network limited 24.16% of the time.
Web100 reports TCP negotiated the optional Performance Settings to:
RFC 2018 Selective Acknowledgment: ON
RFC 896 Nagle Algorithm: ON
RFC 3168 Explicit Congestion Notification: OFF
RFC 1323 Time Stamping: OFF
RFC 1323 Window Scaling: ON
Information: Network Middlebox is modifying MSS variable
Server IP addresses are preserved End-to-End
Information: Network Address Translation (NAT) box is modifying the Client's IP address
Server says [xxx.xxx.xxx.xxx] but Client says [xxx.xxx.xxx.xxx]

Svchost.exe slowing down my system terribly

svchost.exe slowing down my system terribly. I ran the Kapersky program and no virus files came up. I am getting desperate. I am ready to kill my computer. Why is this process such a hog and how can I stop it?

To find what is causing your computer to use more CPU than it normally does you need to run this.
Install the WPT (windows Performance Toolkit) http://social.technet.microsoft.com/wiki/contents/articles/4847.install-the-windows-performance-toolkit-wpt.aspx ,
Open a CMD prompt with administrative rights (right click it>run as admin) and run this command for 60 secs to capture the high cpu usage:
xperf -on latency -stackwalk profile -buffersize 1024 -MaxFile 256 -FileMode Circular && timeout -1 && xperf -d cpuusage.etl
The trace will run and give you a warning then revert to a C:\ prompt
The log will be in C:\windows\system32.
It should be called cpuusage.etl
Please zip the file and upload it to skydrive (or another file sharing service) and put a link to it in your next post.
Wanikiya and Dyami--Team Zigzag

Hi, I am using an old PC P2 450Mhz, 256 MB Ram. Is ver 3.6.16 ok for my system or will it slow down the system? Thanks

Hi, I am using an old PC P2 450Mhz, 256 MB Ram. Is ver 3.6.16 ok for my system or will it slow down the system? NODD is the anti-virus. I am not happy with IE or goolge as these are taking too much space. Thanks

The system requirements for Firefox 3.6 are:
* Pentium 233 MHz (Recommended: Pentium 500 MHz or greater)
* 64 MB RAM (Recommended: 128 MB RAM or greater)
You exceed the minimum and are just short of the recommended processor. It should run OK but the only way to tell will be to try using it. Note that using add-ons can slow Firefox down, so if you start installing quite a few you may get performance issues.
https://www.mozilla.com/en-US/firefox/3.6/system-requirements/

Does a partition for Boot Camp slow down your system?

I'm gonna make a partition on my disk for bootcamp. Does adding a partition slow down your system when using Mac OS? I assume boot camp assistant creates a partition wherever there is enough required free space. And if this free space is in the middle of the disk, doesn't the system have to skip back and forth over the partition to access data?
Or does boot camp assistant create the partition at the end of the disk?
Thanks for your replies.

Boot Camp partition is generally created at the end of the disk so to speak. While the partition is created, files are moved and arranged so that there is a contiguous space for the partition.
NO it does not affect the OSx performance at all as long as you have enough free space in the OSx partition for it to perform satisfactorily.
Axel F.

Cant "see" external ADSL modem [D-link model DSL-500B]

Hi guys!
Im here in poor Brazil, and I just bought a new DSL-500B external ADSL modem, and I can make this machine turn to router, to stop login every time I turn on the computer.
The manual says that the IP is 192.168.254.254, but Firefox and Safari cant "see"... I ping, and cant find... I tracerout to a google site and the modem dont appear, its invisible!
Im properly conected on web... But I have this little problem...
I dont know what to do...
Please good people, help me!
Thanks,
Daniel
Brazil
iMac Mac OS X (10.3.9)

Nothing, mate...
Firefox can't establish a connection to the server at 192.168.1.1.
* The site could be temporarily unavailable or too busy. Try again in a few moments.
* If you are unable to load any pages, check your computer's network connection.
* If your computer or network is protected by a firewall or proxy, make sure that Firefox is permitted to access the Web.

DSL speed slow down after 10.5 upgrade :(

Hello all,
I have a question, and need the Apple cyber-community to help me with this one.
I have A.T.& T.'s DSL service. I have a 2WIRE 1701HG router-DSL modem. I HAD 1.2mg download speed 99% of the time with MacOS 10.4.x. Yes I know that it is not very fast, but I live in the country side and am at the VERY VERY end of the line of service.
After I upgraded to MacOS 10.5.x, my down load speeds have slowed down to around 200 to 850bps. I have checked my hardware, and all seems fine. I called A.T.&.T and they ran a speed check and said I was getting 1.5 speed. Any ideas how to fix the issue?
Thanks,
Apple //GS

PS: "Get a Windows Vista computer!!" That was what I got from the tech at A.T.&T. "They don't have this problem....................."
Apple //GS

When downloading CS 5.5 from the direct link it eventually slows down and stops. How am I supposed to download the file?

I am trying to download CS 5.5 on to my new laptop since my old one died. I am using the direct link found Download CS5.5 products. It starts off fine but it slows down and eventually stops. How am I supposed to download the entire file? I am using Chrome on Windows 8.1 if it makes any difference.

Adding to What Anand has mentioned, please make sure that any online active Defence system should be turned off ( For eg, Kaspersky, Norton or AVG ). Also, if you are behind a corporate network, please try a different network and check again.

Safari slowing down my system?

I swore by Safari when I first started using it back in 2008, but the latest version with 'webkit2webprocess.exe" is causing some huge slow downs. I just can't figure out what's wrong, and why safari is sudenly a lumbering beast instead of the sleek predator that it used to be.
My system constantly caches, the bhard drive is constantly w eatorking with this thing installed. It eats up RAM, and more ram, and never dumps anything, untiol there's no more page filing space. Even now, after I wrote that last sentence my HD went active again. Sure enough, "webkit2" is eating up naerly a half gig of ram. And now when I type, I can't see what I'm typing. and now it's eating up my video ram because I've run out of file page space.
who the upgraded this thing, the marx brothers?
thjis used to be the best brower on the market, but hnow it's JUST a piece of ram eating junk.

I also finger McAffee as the culprit, it's not necessary on Mac's as of 10.6.8+ Apple installed their own anti-OS X malware detector and it checks for updates like every 26 hours or so.
If you need to clean the Windows malware off their files, the free ClamXav does the job nicely and doesn't bugger up the machine as it's run as you need it.
For your other slowdown issues, I suggest you look through these tips of mine, my Snow Leopard is incredibly fast.
Why is my computer slow?
Diagnosing network issues
Tune up your Mac here
For Snow Leopard Speed Freaks
https://discussions.apple.com/community/notebooks/macbook_pro?view=documents

HT2055 Why does iPhoto crash or slow down my system significantly?

When I use iPhoto to import or work on my photos, it slows the entire system down big time and iPhoto itself continuously shuts down and I have to reopen. Just to import photos it takes several attempts to successfully get them imported to iPhoto. I love iPhoto and what it does but it is killing my system! Help!

What version of iPhoto and system are your running? How much free space do you have on your boot drive. Post just the first 50 lines of the crash report.
OT

The little gear wheel keeps appearing thus slowing down the system

My system is being slowed down by the appearance of the little gear wheel turning around & around.

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
The title of the Console window should be All Messages. If it isn't, select
SYSTEM LOG QUERIES ▹ All Messages
from the log list on the left. If you don't see that list, select
View ▹ Show Log List
from the menu bar at the top of the screen.Click the Clear Display icon in the toolbar. Then take one of the actions that you're having trouble with. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message by pressing command-V.
The log contains a vast amount of information, almost all of which is irrelevant to solving any particular problem. When posting a log extract, be selective. A few dozen lines are almost always more than enough.
Please don't indiscriminately dump thousands of lines from the log into this discussion.
Please don't post screenshots of log messages—post the text.
Some private information, such as your name, may appear in the log. Anonymize before posting.

Select statement from bkpf slows down the system

hi guys,
i have this syntax for this coding:
        SELECT * FROM bkpf
         WHERE bukrs = ekko-bukrs
           AND awkey = xawkey
           AND gjahr = i_ir-budat(4)
           AND blart = 'RE'.
        CLEAR: titab.
        titab-ebeln = itab-ebeln.
        titab-ebelp = itab-ebelp.
        titab-budat = bkpf-budat.
        titab-bldat = bkpf-bldat.
        titab-xblnr = bkpf-xblnr.
        APPEND titab.
     ENDSELECT.
this coding really slows down the report seleection and sytem , can anybody advice on how to select the better way

Hi Ester,
First you need to avoid the select and endselect statement by using SELECT INTO TABLE.
Second issue is u are using non-key fields in where conditions are aweky, belnr and u r not using the belnr which is first key-field in the BKPF table.
Third one is try to use the fields in correct order which it is in table say in ur where codition it should be like bukrs, gjahr, blart, awkey,....
if you dont have a input field BELNR and u need to do really improve the performance with these input fields wht you have, its is better to create Secondary index with proper sequence for felds.
But i am not sure to give permission to create secondary index bec it takes more memory occupation like what exact BKPF tbale contains, you need to permission from client people along with BASIS people.
i am give sample code :
SELECT * FROM bkpf " try to specify the internal table with exact fileds instead '*'
    into table tbl _ bkpf
WHERE belnr = w_belnr
and    bukrs = ekko-bukrs
AND gjahr = i_ir-budat(4)
AND blart = 'RE'.
AND awkey = xawkey.
If sy-subrc = 0.
sory tbl_bkpf by belnr.
endif.
Let me know if any doubts.
<b>Reward with points if useful.</b>
Regards,
Vija

My DSl is slowing down why?

over the past 2 weeks I have noticed the computer running slower and slower on the net. I powered it down including the modem and rebooted it.
I pay for the 1.2-1.7 Mbps plan
I tried 2 different tester my speed sites and got the same results
Upload .5 Mbps
download .36 Mbps
What is the deal with that I'm almost 1/4 the speed of what I pay for? I tested it at night and I know it's slower but even during the day in the the middle of the week it seems like my connection is running with the parking brake stuck on. Any easy fix?

OK.
With the router disconnected from the modem and with the PC connected directly to it, are you able to visit the modem's web interface at http://192.168.1.1/ or another address, if you changed the modem's IP or do you currently have your modem set up as a bridge so the router can take care of the connection entirely? A good way to tell if your modem is bridged or not is to check the Internet light. If that light is out yet your Internet works it's bridged.
========
The first to bring me 1Gbps Fiber for $30/m wins!

CPU and GPU slow down after system upgrade

Ok, I can't find anything similar to the question I have...but this forum goes on forever
As my system specs appear below, my machine was running quite comfortably a week ago, with same setup...minus the acrylic case and second 120GB hard drive.
At that stage I had "nomal" benchmarking scores 3dmark03 - 5850, Aquamark3 41.000, PC mark 2002 - cpu7020 mem8438 hdd1050.
Life was good and I loved my system
Then I decided it would be cool to upgrade to an acrylic case (which has better cooling with 3 fans) and a second 120 GB HDD to make a striped raid array.
My first concern was the raid Array. I was carefull to buy the exact same seagate hard drive, size etc. the original was only a month old anyway. The second was to use the intel southbridge chip for SATA RAID or the Promise controller? After researching these forums I decided to go with the Intel as it has more possible bandwidth and doesn't sit on the PCI bus.
I got the new case and wearing those stupid white gloves, proceeded to move the components over and trash my "old" metal case.
The windows NTFS format (full) flew by in 30 seconds and I was really impressed.
Once windows xp and all it's drivers and updates were installed, incl sound and graphics etc. I did a 3Dmark 2001 test before upgrading to Dx9...what a bad mark! 3Dmark2001SE - 9950 (terrible for this system).
I thought it was a DX problem...so I installed Dx9
Then opened that corecenter program (the old one, the one that doesn't crash...)
and my CPU was about 5c hotter than usual, it was running at 40-42c (I have standard intel cooling fan). It went up to 55 at times when running PC mark 2002.
This didn't concern me too much a the system was stable at 32-34c and the northbridge read 60c (but we all know that's not true , more like 35ish.
My PC mark 2002 is now cpu4200 - mem4800 - hdd1800
(at least the HDD improved!) LOL
I ran Aquamark3 next...29,900 (ouch!)
Previously my CPU was 8,700 and GPU was 5300
now the CPU read 4400 and the GPU 4600
I don't really notice the speed loss when working, but games and benchmarks tell a different story.
So, My question: What has happened? Why is my CPU power cut in half? and the graphics card slightly slower? The memory speed stayed the same and the HDD speed improved....not a worthwhile upgrade IMO
What went wrong?
Here are my theories.
1) The CPU and system case is getting too hot
Does the CPU "throttle" when it overheats? this could be the reason.
Also both HDD get really hot and the fan in front blows air over them, this hot air could be going over the CPU or GPU. Maybe get 2 HDD coolers?
should I buy a better CPU cooler like the Thermaltake spark7+ ?
2) The PSU does not have enough watts
I couldn't find traces of voltage lack or spikes...but it could still be a problem
3) The RAID0 array is a strain on the CPU and chipset
I'm not sure about this.
My appologies for the lengthy thread, but I wanted to be sure that anyone trying to figure this out had as much info as possible
Thanks if u can help me figure this out.

Quote
Originally posted by Reaver
When I originally installed the intel p4 cooler, I used artic silver ceramique paste...and the CPU temp operates at 36-38c with no load.
Perhaps I should upgrade the overall cooling. Get a Thermaltake copper fan and two HDD coolers.
Well, your temps sound allright, no need to worry them, if they really operate at that level.
Quote
The solution to set the FSB to 201Mhz sounds good. But do I set this in the BIOS or with Corecenter in windoze?
Propably meant to adust your FSB at BIOS, at least that is what I would suggest.
Quote
I will try to re-install the VGA drivers because something strange DID happen when I first installed them. I started with the hercules driver CD, this installed CAT 3.2 drivers. I then upgraded to CAT 3.7 and before it completed I got an error window (send, dont send).
Remove drivers AND ATI control panel first, and then re-install. Use drivers from ATI site, and rather Catalyst 3.7. I Have had problems with 3.8 Catalysts.
Quote
Still wouldn't explain why the CPU seems so crippled. I have managed to get a "normal cpu score of 7000+ in PCmark2002 by shutting down, restarting later and killing every process except explorer.
Do you have any processes that seem to eat more juice thant hey should? Arrange your processes by CPU usage and see if there is something strange.
Quote
If this cant be fixed I will reinstall over the weekend. Does anyone know of the RAID0 array on the southbridge causing a system slowdown?
I'm using Intel RAID and it works perfectly, no extra CPU usage is shown and it's pleasantly fast!
And Install latest Intel INF updates and Application Accelerator from Intel site. That's what I'm using, and works fine.

Websites that slow down your system

My system was running slow there for a while, so I looked in activity monitor and found that safari was using up a huge chunk of my CPU. I managed to narrow this down to a particular site that I recently started visiting. Is there anyway that I can change my settings so as to use this site without it monopolising my CPU?

This issue may be the same as these as the symptoms are similar:
http://discussions.apple.com/thread.jspa?messageID=9522744,
http://discussions.apple.com/thread.jspa?messageID=9592205
and http://discussions.apple.com/thread.jspa?messageID=9399361
Before the situation TLP describes in his thread (9399361) I also encountered that Safari was using the amount of CPU you describe here.
This is an odd issue.
Regards, TOm

ADSL modem D-Link DSL-G684T slow down my system

Similar Messages

Maybe you are looking for