AE BASE Station upgrade?

I have an older....not even sure because we have been using it for SO LONG..... AE BASE STATION. It is the one that is shaped like a UFO. Recently, we have been experiencing the occasional power outage in our area, which is not uncommon. When the power comes back up, it is rare that the router comes back up normally. I nearly always have to do a complete reset of the modem and router and wait for sometimes hours before I see the longed for BLINKING LIGHT to have a connection! COULD it BE that this old router is just ready to be replaced? Or could the Cat5 or Cat5E cables need to be replaced? Do these things make a difference? It is just frustrating why this is happening more and more all the time. I noticed our neighbors router signal comes right back on without a hitch after a power outage.
Input MUCH appreciated. Guess we have been lucky to be using this old dinosaur for all these years, eh

Cable you have will in most cases be fine.
You do not need to use the CD.. most Macs have no cd/dvd drive now anyway.
Everything is there for the setup in airport utility which is simply part of the OS.
Just plug the newer AE into the modem or router and run the airport utility.. I have no idea what modem or router you have but the setup will depend on what is already there..
eg a cable modem is generally modem only.. if it is single ethernet port it is certainly modem only.. the AE is then going to function as the router.
If the modem is adsl and has 4 ports plus maybe wireless then it is a modem router and the AE is put into bridge mode.. ie.
You might need to play with the utility a bit to get used to the way it works.
Please post back if you run into troubles.. give the exactly make and model and the modem and tell us the ISP you are with.. that gives a good hint towards the setup.
N wireless will be faster but the range will not be very different. The older extreme had a very good antenna assembly.. only really improved on by the latest AC model.

Similar Messages

Airport extreme base station - upgrade worthwhile?

I have discovered that my ISP has capped my broadband at 2mbps so I am changing to one promising up to 8mbps. Now my attention is engaged, I have started looking at a new wireless router but am confused about speeds. Is there any point in upgrading my old airport base station to the 802.11n?
My present one says it broadcasts up to 54mbps which sounds way faster than anything coming down my phone line.
As I see it, I would be putting a 6 lane highway at the end of a country lane, so I must be missing out on something.
Please tell me if I am misunderstanding something.
Cheers
Ian

The only advantage you would gain by moving to an "n" router would be faster communications on your local area network. In other words, if you want to copy files back and forth from a computer to a hard drive, etc, your current limit is 54 Mbps. In real life, the actual transfer speed is about 1/2 to 2/3 of this figure.
If you move up to an "n" router. It will have speeds up to 130 Mbps on the 2.4 GHz band and up to 300 Mbps on the 5 GHz band. Copies will go much faster at the higher speeds, anywhere from 3-5 times faster or more on average.
If you plan to stream high definition video over your wireless, the higher speeds will definitely improve the quality of the experience.
As you note, your current 54 Mbps router is much faster than your internet connection. The internet connection is almost always going to be the "choke point" on any home network. If your service is limited to 8 Mpbs, that is the maximum speed you will get. It will make no difference whether you use a 54 Mbps router or higher speed "n" router on this type of connection.
You did not mention whether or not a "Guest" network feature would be important to you, or whether the newer dual band routers would allow your devices to connect more effectively, so we can advise on that subject.
Message was edited by: Bob Timmons
Message was edited by: Bob Timmons

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light.

I have an Airport Extreme Base Station and have recently upgraded to Mountain Lion. Now airport utility won't work with my base station so I bought a Time Capsule. For the life of me I can't make the substitution work and only see a blinking amber light. Can anyone who has made this change offer some advice?

apikoros wrote:
The Utility transferred all of the AE's settings, so I still have to change the password, which leaves me with only 2 other questions, I think:
1) I assume it's just a matter of using the Utility, entering a stronger password and checking for it to be remembered in Keychain Access. But do I have to change the password for each individual unit-- the TC, the Extreme and both Expresses-- or will changing it just for the TC alone work for the entire network?
Resetting the password you will need to do for each device... the utility cannot even see those old units.
So you will have to do it for each one.. think it through.. because as you change passwords the others will lose connection.. so start from the express which are wireless extending .. change those first.. and go back up the chain.. as each one changes it will drop off the network.. until you reach extreme and change that. Then you might need to reboot the whole network to get everything talking again. If something goes wrong.. just pluck that one out of the mix and plug in ethernet.. reset and redo the setup. That is my preferred method anyway.. do everything in isolation one by one. By ethernet and then nothing goes wrong.
2) Who's the treasonous SOB who spilled the beans to you about the ICBM in my back yard?!?
N.Korean hackers.
[Edit] Whoops-- one more question: I want to partition the TC's disk, but Disk Utility doesn't see it. What do I need to do?
You cannot partition a network disk. And apple provided no tools for it in the TC itself. You can pull the disk out and partition it but that voids your warranty. (although done with care who is to know).
Look at Q3 here.
http://pondini.org/TM/Time_Capsule.html
Mixing TM and data on the TC is worth planning carefully. They don't necessarily sit happily together.

Can i upgrade my base station with airport in mountain 10.8.5

can i upgrade my base station with airport in mountain 10.8.5

can i upgrade my base station with airport in mountain 10.8.5
Please check on the side or bottom of the AirPort Express to locate the model number. It will start with an "A" followed by four numbers.
If you have A1084 or A1088, you will not be able to administer these older versions using the iMac running OS X (10.8.5).
If you have model number A1264 or A1392, you can check to see if there are any available updates as follows:
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click on the AirPort Express icon
Click on the Version number that appears in the small window
You will be notified if an update exists for your AirPort Express

I lost my connection with my AirPort Base Station when I upgraded to the OS Maverick. How can I get my system to recognize the base station again?

I lost my connection with my AirPort Base Station when I upgraded to the OS Maverick. I can still see the Internet, but the Time Machine cannot backup now because it cannot locate the AirPort base station. How can I resolve this issue?
Steps already taken with zero success:
1. Restarted the AirPort Base Station multiple times.
2. Restarted the Mac Pro multiple times.
3. Looked online for AirPort update for 6.3.2 version.
Other Apple products in my house can still see the AirPort Base Station, however my Mac Pro and Mac Book Pro cannot.
Please advise.

That information helps. If you want to use one of the SmartStor's disks as a repository for sharing your iTunes Library, then do not configure that disk as a RAID. Format it with Disk Utility using the Erase tab. Mac OS Extended (Journaled) is the correct choice.
Connect it to your Time Capsule, then use AirPort Utility to configure access requirements for sharing it on your network. It should appear as a shared volume in the Finder, available to all your Macs as you thought it should.
I also thought maybe the extra HD space would be added to the existing Airport Disk. It isn't.
Correct. There is no way to do that. The only way to increase the capacity of a Time Capsule's hard disk is to replace the Time Capsule (or its disk, if you are amenable to disassembling it) with a larger capacity model.
If you also want to use the SmartStor as a RAID, that is another story, and you should probably attack that problem separately.

Lost airport base station after upgrade

I started the airport utility which noted that there was new software for my base station available, which I downloaded and installed. After that I lost my base station... I have a Thomson router which got immediately corrupted as well. Now I have to choose between the Thomson or the Airport. I can't have them at the same time.
Anyone a suggestion ??
thanks in avance
Airport purchased 3 weeks ago...

I left the base station unplugged for the whole night.. as soon as I plug it in I loose my complete network and I can't access the base station to change the settings. I have to unplug it again and restart my ADSL modem to get my network up again.
This is very frustrating, espacially because averything worked fine before my upgrade..

Airport express bases station no longer visible after W7 upgrade

Hi - I just upgraded my Dell Inspirion 530 to Windows 7 Ultimate. Since doing so, I can no longer "see" my Airport Express Base Station (1st generation). It is not visible via Airport Express Utility (5.5.3), nor as a connected device through Devices and Printers. I believe there may be a firewall or network security (Symantec anti virus) setting that I need to configure, but do not know where to start. The device worked fine in my Windows Vista configuration prior to upgrading, so I am confident that it is not a Express device issue. The device shows Green, indicating that it is working properly. Help appreciated!!!

do you still ahve signal!! i mean are you able to find the signal when you try to connect to it and use the internet?
if you are able to connect to the intenet on the same machine, did you try updating the untility software?

How can I set up my time capsule as the primary base station with a centurylink router? I'm trying to extend my coverage, increase signal strength, and be able to connect a printer.

I recently moved and now I'm trying to set up my Time Capsule as the primary base station or router with an existing network that has a Centurylink modem/router. The TC still has the settings for my old network. I also have backups on it. I have the data backed up to another HD so it's not an issue to return it to factory settings if doing so deletes the back ups. Do I need to restore it to the factory settings to set it up? Also, what settings would I select on the TC (and the Centurylink modem/router) in order for the TC to serve as the router, instead of the Centurylink router? I want to be able to use the TC to back up my Mac's, print wirelessly, and improve overall performance. I tried setting the TC up and ended with 2 different networks. Can anyone please help me with this?

The TC has to plug into the existing modem router by ethernet.. you cannot use wireless.
You have a choice of which is router.. only if Centurylink agree to bridge their modem router.. this has to be done by the ISP and often they do not allow it.
Is your broadband cable or adsl or fibre or ???
If it is cable and you are allowed to purchase your own cable modem pick a pure modem version with no router in it.. plug the TC into it by ethernet.
Setup the TC in DHCP and NAT mode.. (depending on broadband type).
You must reset the TC to factory to do the setup.. no files are lost at all.
Here is my current recommended setup.. with Yosemite life has become harder than ever.
Factory reset universal
Power off the TC.. ie pull the power cord or power off at the wall.. wait 10sec.. hold in the reset button.. be gentle.. power on again still holding in reset.. and keep holding it in for another 10sec. You may need some help as it is hard to both hold in reset and apply power. It will show success by rapidly blinking the front led. Release the reset.. and wait a couple of min for the TC to reset and come back with factory settings. If the front LED doesn’t blink rapidly you missed it and simply try again. The reset is fairly fragile in these.. press it so you feel it just click and no more.. I have seen people bend the lever or even break it. I use a toothpick as tool.
N.B. None of your files on the hard disk of the TC are deleted.. this simply clears out the router settings of the TC.
Setup the TC again.
ie Start from a factory reset. No files are lost on the hard disk doing this.
Then redo the setup from the computer with Yosemite.
1. Use very short names.. NOT APPLE RECOMMENDED names. No spaces and pure alphanumerics.
eg TCgen5 and TCwifi for basestation and wireless respectively.
Even better if the issue is more wireless use TC24ghz and TC5ghz with fixed channels as this also seems to help stop the nonsense. But this can be tried in the second round.
2. Use all passwords that also comply but can be a bit longer. ie 8-20 characters mixed case and numbers.. no non-alphanumerics.
3. Ensure the TC always takes the same IP address.. you will need to do this on the main router using dhcp reservation.. or a bit more complex setup using static IP in the TC. But this is important.. having IP drift all over the place when Yosemite cannot remember its own name for 5 min after a reboot makes for poor networking. If the TC is main router it will not be an issue.
4. Check your share name on the computer is not changing.. make sure it also complies with the above.. short no spaces and pure alphanumeric.. but this change will mess up your TM backup.. so be prepared to do a new full backup. Sorry.. keep this one for second round if you want to avoid a new backup.
5. Mount the TC disk in the computer manually.
In Finder, Go, Connect to server from the top menu,
Type in SMB://192.168.0.254 (or whatever the TC ip is which you have now made static. As a router by default it is 10.0.1.1 and I encourage people to stick with that unless you know what you are doing).
You can use name.. SMB://TCgen5.local where you replace TCgen5 with your TC name.. local is the default domain of the TC and doesn't change.
However names are not so easy as IP address.. nor as reliable. At least not in Yosemite they aren't. The domain can also be an issue if you are not plugged or wireless directly to the TC.
6. Make sure IPv6 is set to link-local only in the computer. For example wireless open the network preferences, wireless and advanced / TCP/IP.. and fix the IPv6. to link-local only.
There is a lot more jiggery pokery you can try but the above is a good start.. if you find it still unreliable.. don't be surprised.
You might need to do some more work on the laptop itself. eg Reset the PRAM.. has helped some people. Clean install of the OS is also helpful if you upgrade installed.
Tell us how you go.
Someone posted a solution.. See this thread.
Macbook can't find Time Capsule anymore
Start from the bottom and work up.. I have a list of good network practice changes but I have avoided Yosemites bug heaven.
This user has had success and a few others as well.
RáNdÓm GéÉzÁ
Here is why Yosemite has fundamental issues.
http://arstechnica.com/apple/2015/01/why-dns-in-os-x-10-10-is-broken-and-what-yo u-can-do-to-fix-it/

How do I configure an Airport Extreme base station to receive and distribute a wi-fi network from a broadband wireless router?

I have recenly upgraded my broadband service and now have a wireless router. My old network configuration was a router connected by ethernet cable to an Airport Extreme base station which then broadcast my wireless network (I also had an Airport Express base staion set up as a wi-fi booster elswhere in the house).
I now have two networks (my original network and the new network from the wireless router) and wish to amalgamate these into one.
Ideally I wish to use the Airport Extreme base station as the "remote" booster (I have purchased Powerline adapters for this purpose) but don't know how to configure the Airport Extreme base station in order to to this.
Can you advise on the best set up for this please?
My Mac is running OS X 10.8.2 and the Aiport untility is version 6.1.
Thanks in anticipation.

The AirPort Extreme should be configured to "create a wireless network" with the same WiFi network name, security type (usually WPA2 Personal) and password as your existing router. It should be configured as connection type Ethernet and be in bridge mode.

Why can I no longer print from my Windows XP computers to my Bonjour connected Canon printer thru an Airport Extreme Base Station (f/w 7.6.4, model A1301)?

Something has changed recently and I haven't figured it out. My 2 Windows XP computers are no longer able to print via Bonjour. I have tried removing and reinstalling Bonjour. Upgrading the firmware on the AIrport Extreme Base Station and comparing Port settings from an able to print Windows Vista laptop. Port settings match and Bonjour says it sees the printer...but the communication is not happening between the computer and the networked printer, it times out and produces an error in the print que. Both XP computers have no problem using the internet via the Base Station. One is wired and one is wireless. Thoughts?

Sounds a bit like a problem being discussed in this thread:
http://discussions.apple.com/thread.jspa?threadID=2651093&tstart=0
I suspect some kind of update is at fault. Like you, my printer/base station setup had been working fine until recently.

Extreme Base Station suddenly dropping internet connection

I have an Extreme Base Station (802.11n Fast Ethernet) which has been providing wireless internet and printing to two imacs pretty flawlessly for several years. It seems to be a fairly simple network. DSL modem (to WAN port) and USB printer cable plugged into back of Base Station.
Several days ago, the Base Station began dropping connection to the internet every few minutes. If I connect the modem directly into the computer, I have no problems with losing connection. So, I began looking for solutions online and have been trying everything I could find to do. I've scoured the forums here, and everywhere and read a bazillion posts.
I've done a hard reset of the Base Station, I've tried different channels, I've unplugged, waited ten minutes, and replugged in a myriad of sequences, including unplugging both the modem (Zhone/Paradyne 6381-A3) and Base Station overnight. The only thing I haven't done is roll back the firmware (currently 7.4.2 I believe). I'm still experiencing the same problems and am at my wits end. I've spent hours now trying to fix it and need to do other things like shop for groceries and vacuum! So, I'm posting, in hopes someone might be able to point me in a more productive direction.
Is it possible the Base Station hardware is failing? What are the signs and symptoms? I hate to spend another $179 and still have the same problems.
Thank you.
Most kindly,
---Susan

.
Dear Bluenova - ( +or other interested readers+ )
I know that this reply is two months since this topic was initially posted.
This is a longstanding Airport Extreme ( AEBS ) problem that's been noted since 2006-2007.
It has been an ongoing issue for me -AND- I continue to experience it even after recently upgrading my AEBS.
I finally called AppleCare in mid-Sept. and opened a formal problem case report.
As of today (Oct 15, 2010) I still have an open & unresolved case with AppleCare.
The problem has been escalated twice -and- is now referred to Engineering Dept for research & resolution.
I was curious what steps or actions you have taken -and/or- if you still experience the problem.
_Readers Please Note_
Many users have posted messages regarding problems with Airport Extreme *+DROPPING CONNECTIONS+* .
However, with careful reading, it becomes obvious that many forum posters are not sufficiently clear
-and- often confuse or do NOT make the distinction between ..... DIFFERENT TYPES OF CONNECTION PROBLEMS.
. ( wifi/network connection probs - vs - internet connection probs )
SEE HELPFUL POST BY WILLIAM KARCHINSKI
Topic : *+Having issues with your AirPort connection? Please be specific+*
http://discussions.apple.com/thread.jspa?threadID=2227197
FWI
If you suspect that you are having the *dropped internet connection* type problem,
YOU CAN CHECK & WATCH IT HAPPENING IN THIS MANNER
Set Airport in Menubar to *"SHOW TIME CONNECTED"*
. *- +and also+ -*
Open Airport Utility --> AIRPORT --> SUMMARY window
.... and leave it visible somewhere on your screen while you web browse.
Now, once the internet connection drops or is lost ...
... in the Airport Utility Summary window - you will see the loss of the assigned IP Address
. *- and -*
.... in the Menubar - the time connected will reset to 00:00:00
If you have a new or ongoing problem that relates specifically to ....
.... Airport Extreme – dropping or losing *Internet Connections* ... ( +not wifi connection type probs+ )
.... please let me know.
I would like to be able to correspond directly with others via email to share info
(such as what modems, ISP's, time of day or conditions with which this problem has been found to occur)
I will then be glad to pass that info on to AppleCare in trying to find a cause (and solution) for this problem.
If this issue was treated collectively maybe AppleCare would address it with more resolve & urgency.
I'll check back with this thread for replies from other interested users.
.

Extreme base station worked, but no internet,... now locked out.

Situation:
Cable modem connected to Extreme base station. Powerbook G4 with 10.3.9 and iMac with 10.3.9 connected by airport to base station. This has been working for more then a year. This morning I had no internet connection on the G4 or the iMac.
Actions taken:
- resarted base station -> no result
- restarted modem -> no result
- checked connection to Base station -> good wireless connection; I could ping the base station, but nothing beyond
- connected Powerbook directly to modem by cable -> internet works
- checked settings base station -> base station seemed to obtain a normal IP address trough the modem
- hard reset of base station -> no result
- upgraded firmware to 5.7 -> got message "An error occurred while reading the configuration." when using the airport utility
- tried using password 'public' -> same message
- connected by cable to base station -> same message
So things certainly didn't improve since this morning. What else can I try?
regards, Wim
Powerbook G4, iMac Lime Mac OS X (10.3.9)

Thank you Will,
Today I upgraded the airport software on my Powerbook and was able again to connect to the Base station and use the airport utility. But I still could not connect to the internet.
Your post made me rethink my troubleshooting. I did restart the modem, but never disconnected it for more then a few seconds. I just tried it again, left it unconnected for over a minute and now it works again.
So thank you very much, your reply was very helpfull.
Regards,
Wim

Base station no longer detected (see post also in Airport Express Forum)

I have stuffed up configuration settings for Airport Express via the Airport Admin Utility and can't undo them.
- Mac OS X 10.5.3 on iMAC
- AX Model number A1088
- Airport Utility 5.3.2
- Airport Admin Utility for Graphite and Snow 4.2.5
I originally set up AX on Tiger - no problems. I upgraded to 10.5.3 still no probs.
While trying to set up a wireless connection for my MP600R printer, I was 'experimenting' to help it find the access point. I went to Airport Admin Utility for G&S (don't know why!), clicked 'configure' and set up the base as WDS thinking this would help the printer detect access point. I had never previously touched Graphite and Snow and never set anything up.
Result was that Airport Utility/AX could no longer detect my network and I lost wireless internet connection.
I went back to Admin Utility but 'configure' button is greyed out. I tried manually connecting to network name but had password problems. I tried to reinstall AX from disc but I got an error saying AX not compatible with the selected drive (which is now 10.5.3)!! I reset AX but I can't restore passwords because AX Utility can't find my network!
HELP!

Firmware is uploaded onto the base station itself and is different from AirPort Utility. Although you probably cannot confirm it without connecting to the base station, I think it highly unlikely that you use a firmware version earlier than 6.1.1 (which came out in 2004). If newer firmware is contained in software on your computer, AirPort Admin Utility and/or AirPort Utility should have prompted you to upload it to the base station, whereas if it is not on your computer, Software Update (assuming you use it) should have prompted you to obtain it. Even if your firmware is older than version 6.1.1, the reset procedure is virtually the same--in that case, you won't see the AX's status LED flashing rapidly a few seconds after you start holding the reset button, and you will just need to hold the reset button for 10 full seconds.
Once you connect to the base station, you should be able to see the firmware version (e.g., "Base Station Vx.x" where x.x is the firmware version) on the opening screen of AirPort Admin Utility for Graphite and Snow, when the base station is highlighted. I imagine that AirPort Utility shows similar information. I believe that in AirPort Utility, you can also check to see if newer firmware is available from Apple (choose "Check for Updates" in the AirPort Utility menu). To the best of my knowledge, the most current firmware version for AirPort Express is 6.3.

Airport Base Station No Longer Found in Network

Since applying the 10.5.2 upgrade yesterday my home network, routed via a cable modem and a formerly dependable original Airport Base Station, is no longer recognized by Airport Utility... and the Airport icon in the finder is continually scanning. I have found, however, that my network shows up as an available option in Network System Preferences...with a Connected status and an IP address (10.0.1.3).
I can connect to the internet and read email from my main iMac because I am also connected directly via ethernet, but my laptop can't find the Airport base station, either. I have reset, unplugged, restarted, check connections and cables, etc. Both Macs easily find my Airport Express, however. I'm concerned the new update no longer supports the original base station...
On another (unrelated?) note, my external backup HD (250GB Seagate), connected by Firewire, is now recognized as "Read Only," whereas it has always had read/write permission (confirmed in Get Info). So now my backup is failing, too. Sorry to introduce a new topic, but I'm frustrated!

Firmware is uploaded onto the base station itself and is different from AirPort Utility. Although you probably cannot confirm it without connecting to the base station, I think it highly unlikely that you use a firmware version earlier than 6.1.1 (which came out in 2004). If newer firmware is contained in software on your computer, AirPort Admin Utility and/or AirPort Utility should have prompted you to upload it to the base station, whereas if it is not on your computer, Software Update (assuming you use it) should have prompted you to obtain it. Even if your firmware is older than version 6.1.1, the reset procedure is virtually the same--in that case, you won't see the AX's status LED flashing rapidly a few seconds after you start holding the reset button, and you will just need to hold the reset button for 10 full seconds.
Once you connect to the base station, you should be able to see the firmware version (e.g., "Base Station Vx.x" where x.x is the firmware version) on the opening screen of AirPort Admin Utility for Graphite and Snow, when the base station is highlighted. I imagine that AirPort Utility shows similar information. I believe that in AirPort Utility, you can also check to see if newer firmware is available from Apple (choose "Check for Updates" in the AirPort Utility menu). To the best of my knowledge, the most current firmware version for AirPort Express is 6.3.

Mountain Lion/Mavericks 'breaks' wifi base station - Snow Leopard works fine

Greetings all,
(Tried this in the OSx forum with no answers, so I figured I'd try the MacMini community and this one.)
I've been reading my way toward blindness through countless threads, here and elsewhere, from countless people, having problem with Mountain Lion and Wi-Fi these last few days, but some are using Airport, some are using third-party Wi-Fi routers, some aren't really specifying what they're using, so I thought I'd be as specific as possible about my situation - and add the fact that everything is still working fine if I boot into a cloned backup using Snow Leopard.
===
So here's the situation. I have a Intel Mac Mini which I use as a Wi-Fi base station for a Intel PowerBook Pro and an iPod 5. The Mini has been running Snow Leopard, and the PowerBook had been upgraded to Mountain Lion a few months ago. Things were still working fine at that point - the PowerBook's shift from SL to ML didn't affect its connectivity as a 'receiver' at all. About a week ago however, I finally upgraded the Mini to Mountain Lion as well (so that I could install the current version of Adobe Lightroom) and lost my Wi-Fi Internet access.
When I turn Wi-Fi on at the PowerBook, the Mini's network is visible, and I get the solid Wi-Fi fan showing a full connection, but I cannot access the Internet (indicated by the exclaimation point inside the fan for the first few seconds). The same is true on the iPod - I get the checkmark showing that I'm connected, but when I try to access any Internet services will get a pop-up box telling me that the Internet is not connected.
After going through pages and pages and pages of people struggling with similar issues on sites like this, and following suggestions like deleting my preference files, repairing permissions, zapping PRAM, creating new locations, changing IP addresses etc. I got no further. But since I had cloned my hard drive just before the upgrade from Snow Leopard to Mountain Lion (thank you SuperDuper), I can reboot into Snow Leopard, and everything still works fine. With that advantage, I copied and re-created EVERY SINGLE preference in the system preferences for Network and Internet sharing* from the Snow Leopard into the Mountain Lion system. (I even went so far as to create a network in Mountain Lion's prefs. with WEP encryption instead of the newer WPA just in case that would make any difference at all.) But even with identical settings on the Mini regardless of booting into Snow Leopard or Mountain Lion, Mountain Lion remains the same - no problem connecting with the network, but complete inability to access the Internet. A few days ago, hoping against hope that an upgrade to Mavericks might reset things into some sort of working mode, I tried that - but no better result.
(*) I note that the wifi heading in the preference panes has changed from "AirPort" in Snow Leopard to "WiFI" in Mountain Lion and Mavericks, but I'm assuming that's just a change Apple made in its terminology to avoid confusion with the external AirPort options.
I would appreciate any suggestions any of you could give. And I would ask that you specify whether any suggested changes are to be made on the originating Wi-Fi station (in this case the Mini), or the receiver (in this case the MacBook). Many of the threads I've read to date can be confusing simply because they're not specifying on which machine any suggested changes need to be made, and while I'm sure there's nothing that needs to be changed at the MacBook, please specify if I'm wrong.
Thanks again,

Greetings all,
(Tried this in the OSx forum with no answers, so I figured I'd try the MacMini community and this one.)
I've been reading my way toward blindness through countless threads, here and elsewhere, from countless people, having problem with Mountain Lion and Wi-Fi these last few days, but some are using Airport, some are using third-party Wi-Fi routers, some aren't really specifying what they're using, so I thought I'd be as specific as possible about my situation - and add the fact that everything is still working fine if I boot into a cloned backup using Snow Leopard.
===
So here's the situation. I have a Intel Mac Mini which I use as a Wi-Fi base station for a Intel PowerBook Pro and an iPod 5. The Mini has been running Snow Leopard, and the PowerBook had been upgraded to Mountain Lion a few months ago. Things were still working fine at that point - the PowerBook's shift from SL to ML didn't affect its connectivity as a 'receiver' at all. About a week ago however, I finally upgraded the Mini to Mountain Lion as well (so that I could install the current version of Adobe Lightroom) and lost my Wi-Fi Internet access.
When I turn Wi-Fi on at the PowerBook, the Mini's network is visible, and I get the solid Wi-Fi fan showing a full connection, but I cannot access the Internet (indicated by the exclaimation point inside the fan for the first few seconds). The same is true on the iPod - I get the checkmark showing that I'm connected, but when I try to access any Internet services will get a pop-up box telling me that the Internet is not connected.
After going through pages and pages and pages of people struggling with similar issues on sites like this, and following suggestions like deleting my preference files, repairing permissions, zapping PRAM, creating new locations, changing IP addresses etc. I got no further. But since I had cloned my hard drive just before the upgrade from Snow Leopard to Mountain Lion (thank you SuperDuper), I can reboot into Snow Leopard, and everything still works fine. With that advantage, I copied and re-created EVERY SINGLE preference in the system preferences for Network and Internet sharing* from the Snow Leopard into the Mountain Lion system. (I even went so far as to create a network in Mountain Lion's prefs. with WEP encryption instead of the newer WPA just in case that would make any difference at all.) But even with identical settings on the Mini regardless of booting into Snow Leopard or Mountain Lion, Mountain Lion remains the same - no problem connecting with the network, but complete inability to access the Internet. A few days ago, hoping against hope that an upgrade to Mavericks might reset things into some sort of working mode, I tried that - but no better result.
(*) I note that the wifi heading in the preference panes has changed from "AirPort" in Snow Leopard to "WiFI" in Mountain Lion and Mavericks, but I'm assuming that's just a change Apple made in its terminology to avoid confusion with the external AirPort options.
I would appreciate any suggestions any of you could give. And I would ask that you specify whether any suggested changes are to be made on the originating Wi-Fi station (in this case the Mini), or the receiver (in this case the MacBook). Many of the threads I've read to date can be confusing simply because they're not specifying on which machine any suggested changes need to be made, and while I'm sure there's nothing that needs to be changed at the MacBook, please specify if I'm wrong.
Thanks again,

AE BASE Station upgrade?

Similar Messages

Maybe you are looking for