After bios update side nomberpad is not workinh keys from 0-9

after bios update side nomberpad is not workinh keys from 0-9

Hello jay04,
Welcome to the HP Forums!
I understand the number keys do not work on your keyboard. I will do my best to assist you. First, I require the following information:
1. The computer's model number. If you require assistance locating this information, please reference this website: Guide to finding your product number
2. The computer's operating system. If you require assistance locating this information, please reference this website to determine your Windows operating system.
3. Does this occur on certain programs, or all programs?
4. Have you installed any new software or drivers on this computer, before the issue appeared?
Additionally, if the issue just began occurring, I would perform a system restore. I want you to bring the computer back to the earliest restore point possible, in an attempt to dodge whatever caused the issue. Here is a document on how to perform a System Restore: System Restore
Thanks!
Mario
I worked on behalf of HP.

Similar Messages

After BIOS update DVD driver do not read DVDs anymore - Sat A80

Hi,
I have a Satellite A80-131 and after bios update (last version 2.5) by windows procedure update, my DVD drive do not read DVD medias anymore. It is possible to read CD medias, but not DVD one.
Can I reinstall the old bios? Can I reinstall the firmware?
Thanks
Ronai Lisboa

Hi Ronai
Like Jimi has said in the posting above. It's very unusual that after BIOS updating the DVD drive hasn't read the DVDs.
Furthermore it's not advisable to use any 3rd party applications to DOWNGRADE the BIOS. Usually only the ASP can downgrade the BIOS. Such procedures are very serious and the wrong procedure can damage the motherboard.
However, it's nice that you have solved the problem and that the drive works properly.
Thanks for the feedback.

After BIOS update failure and rollback, audio hot keys detect press but do not function

All other hot keys appear to function properly, only the mute/audio-/audio+ hot keys do not work.
I can press the key and the vertical volume indicator displays but it does not move.
At this time, I suspect this has to do with the failed BIOS update yesterday. All keys functioned properly before the failed BIOS update.
All HP drivers and software are updated to latest.
Another symptom I don't know may be related is that my bluetooth headphones have refused to connect once now without a full reboot. Bluetooth would connect and speaker audio audio would be muted, and sometimes "Manage Audio Devices" indicated connected to headphones but no headphone audo. Will warrant further watching.
The BIOS update was the most recent as of this writing and attenmpted to update only yesterday. I watched as the new BIOS progressed all the way to the point the BIOS attemnpted to flash and failed, then rolled back. I assume a backup was flashed because all my non-default BIOS settings had to be reset (non-UEFI boot, enable virtualization).
TIA,
Tony
BTW - I find it odd I can't just press a button to export/print my system configuration from the HP Support Assistant, I have to click every individual entry separately, but here goes...
The current running BIOS is F.63
The full results follows
HP ENVY TS 17 Notebook PC
5CG3331YPX
E9G82UA#ABA
Windows 8 64-bit
Intel(R) Core(TM) i7-4700MQ CPU @ 2.40GHz
12GB
4GB Micron Technology 1600MHz
8GB Hynix 1600MHz
Intel(R) HD Graphics 4600
1920 x 1080
60
1965 KBC Version 93.51
F.63
IDT High Definition Audio CODEC
Bluetooth Hands-free Audio

Seems after another day,
The problem resolved itself.
No reboot, no significant changes to the machine I can think of since my original post.
Just a spontaneous self-fix.
Thx,
Tony

After BIOS update Intel Speed Step not working on Satellite A500

I upgraded my Satellite A500 PSAM3E model to the newest BIOS 1.50, now the Intel speed step not working!
My CPU is always 2GHz+, I chagned Power Plan to balanced, but no change... with previous the CPU was around 800 MHz.
When I try to change Windows 7 power management and set maximum CPU performance to 50 or 80% the system freezes.

Hey Szaby59,
Which older BIOS version did you use before update to 1.50?
I also use the maximum CPU performance option for Eco mode (50%) but this does work properly.
Furthermore it would be interesting to know if you use factory settings or your own Windows installation. Normally after using Toshiba recovery disk you dont have to install any Toshiba tools anymore. Everything is preinstalled on your notebook.

After bios update, my window media player got hang and headphone clarity is not proper

HP Pavilion g6 after bios update, my window media player got hang and headphone clarity is not proper

Hello mathewstays,
Which model of g6 do you have? Which operating system? I'll be able to better assist when I know this information.
Thanks,
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Satellite A series does not start up after BIOS update

After bios update with downloaded utility my notebook does not start up.
Did this case covered by warranty?

Im not quite sure if this would be covered by warranty. You should contact the ASP in your country for details but I presume its not covered.
PS: Did you try this workaround:
- remove battery, disconnect the AC adaptor
- wait ~ 40min
- connect both devices again and try to power up the notebook

Problem in booting after bios update

Originally, it was windows home basic was installed in my laptop. But recently I had installed Windows professional. After installation I have downloaded all drivers which are compatible for my laptop model. After BIOS update installation my pc is not booting up at all. Only power button, WiFi and capslock is lighting. Capslock is continuosly blicking. Even FAN speed gets lowered. I have tried hard reset as well as windows+B comand during startup still condition is same. Please reply me....

see help 8....
I am a Volunteer to help others on here-not a HP employee.
Replies aren't online 24/7 because of Time Zone differences.
Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

After BIOS update Satellite L350-172 doesn't start anymore

Satellite L350-172 Bios-Update from bios-20090203164614 to bios-201002250
I just updatet the BIOS of my notebook from 1.60 to 2,20. Now the Notebook doesn't start any longer.
"It was stopped for reason not to damage the Computer" - blue schreen.
How can I downgrade the bios again? Or - what have I to change in the bios-settings?

Hi schuwe,
Im a little bit confused about your posting. How do you tell your BIOS not to restart?
Anyway, after BIOS update you should load the default settings in BIOS.
Did you choose the right BIOS especially for your model?

890FX-65 won't run stable on 16GB after bios update

My Set up:
MSI 890FX-65
1090T Phenom x6
MSI 6950 flashed 2gb frozr III
16gb(4*4gb) Patriot sector 5 DDR3
After live-update updated my bios from the ones that were stock on the board, my system will not run anything graphic intense with out either freezing or BSOD. It ran fine before the bios update, but i am not sure which bios were on the board stock. I have been through all the bios on the website flashing through M-flash, then i have even flashed back to v4.0 with the flash utility here from the forums. I have also run memtest86+ for over and hour and the ram showed no problems. If i take 2 sticks out and run at 8gb dual channel, i get no problems with either pair of ram installed.
Any ideas on what to try?

Quote from: TwiztidUnreal on 09-January-12, 21:59:25
PGV316G1600ELQK
It was a 4*4gb pack, each was in its own plastic package, all 4 packages were in one box. They all also have the same serial #.
i have tested 2 sticks at a time with each stick, and all have passed memtest for an hour per set with no errors at all.
The bios try to run it as 1066mhz @1.5v @ 7-7-7-20 (CL-RCD-RP-RAS) / 27-86-4-8-4-4 (RC-RFC-RRD-WR-WTR-RTP).
I usually set it to @ 1600 MHz @ 9-9-9-24 (CL-RCD-RP-RAS) / 38-88-2-5-12-6-6 (RC-RFC-CR-RRD-WR-WTR-RTP) or
@ 1333 MHz 7-7-7-19 (CL-RCD-RP-RAS) / 29-69-2-4-10-5-5 (RC-RFC-CR-RRD-WR-WTR-RTP), both settings @ 1.65v.
passing memtest doesn't mean that memory is fine.
test each one 2x pack with Prime95: http://www.softpedia.com/get/Others/Home-Education/Prime95.shtml
[Use Large in place FFTs] for at least 5-6 hours per pack
Quote
I usually set it to @ 1600 MHz @ 9-9-9-24
How about if you leave them at Auto?
or manually set to 1333 without chaning timmings.
What about command rate?

Satellite Pro L300: BSOD after BIOS update

Hi
after update the Bios of Satellite Pro L300, the windows not start!
Its show the blue dead screen!
What can i do?

Hi
Are you able to access the BIOS settings?
Im not quite sure why this BSOD appears but possibly the SATA mode settings have been changed after BIOS update
Usually the SATA mode should be set to AHCI if the SATA drivers are installed.
But if the SATA drivers are not included the SATA mode should be set to compatible.
Please check this!
Furthermore you could set the BIOS to the default settings and could try to boot the machine again.

Satellite A100-590 PSAA9E freezes on Toshiba welcome screen after BIOS update

Hi.
Yesterday I did a BIOS update on my Satellite A100-590 PSAA9E-03Z00QGR with the appropriate flash:
http://eu.computers.toshiba-europe.com/cgi-bin/ToshibaCSG/download_driver_details.jsp?service=EU&selCategory =2&selFamily=2&selSeries=153&selProduct=624&langua ge=17&selOS=10&selType=all&yearupload=&monthupload =&dayupload=&useDate=null&mode=userMachines&search =&action=search&macId=&country=all&selectedLanguag e=17&type=all&page=1&ID=58477&OSID=-1&driverLanguage=42
bios-20070709111839.zip
After the flashing procedure the machine rebooted automatically, but unfortunately it now keeps hanging at the Thoshiba welcome screen. Also pressing F2 or F12 won't change anything. It seems like the BIOS is corrupt.
I saw, that in the BIOS package are delivered two flash files (s10gm590.rom and s10pm590.rom). But just executing the SanAntonion10 BIOS590MP.exe a .vbs script is started that decides automatically chooses and loads a flash file. Maybe it chose the wrong one?
What shall I do now? Is there a way to restore the BIOS, or do I have to send my notebook in?
Thanks in advance
MAT

> Satellite A100-590 PSAA9E freezes on Toshiba welcome screen after BIOS update
What to say Marc. It looks like you have used a wrong BIOS version or you have updated the BIOS in wrong way.
You could try to access the BIOS and try to set the settings to default.
Dont forget to save the settings if you will exit the BIOS.
But if this procedure does not help, you will have to contact the ASP in your country.
Possibly the guys will try to flash the BIOS again with other special version.
Good luck
Greetings

Satellite Pro C850 wont work after Bios update

my satellite pro c850 cd wont work after bios update from toshiba.
what do i do?

Saying: dont work you mean it does not power up or what do you mean exactly?
Did you flash the BIOS properly?
Possibly something went wrong during the update and this means that ROM module isnt flashed properly
In most cases a special BIOS crisis disk would be needed to get it working
Not quite sure if you can get it fixed by your own
Check this thread. Maybe it helps:
http://forums.computers.toshiba-europe.com/forums/thread.jspa?threadID=59637
Otherwise you need help from authorized service provider available in your country.

Computer on constant Automatic Repair and Diagnosing loop after Bios Update

I have an HP AiO 23 G010 computer that has decided to stop working after a Bios Update yesterday. It goes on a constant "Preparing Automatic Repair" and "Diagnosing Problem" loop followed by a blue screen that says "Your PC has run into a problem and we are gathering information..." with a face.
I have hit the esc button, f2, and everyother key that I can hit. It only allows me to go to the system screen where I am able to do tests, and checkout firmware management, etc. I tried to roll back the bios update but it would not allow me.
What can I do to fix this?
Thank you

Restore BIOS defaults and if you get into Windows, select a Restore Point prior to when you have problems.
If no go, you may have to perform a factory restore.
Please mark my post as SOLVED if it has resolved your problem. It helps others with similar situations.

I have an Iphone 4 16gb and updated the IOS 6.1.2. after the update my 3G is not working at all??. can you please suggest what can be done to rectify this problem?

i have an Iphone 4 16gb and updated the IOS 6.1.2. after the update my 3G is not working at all??. can you please suggest what can be done to rectify this problem?

I have the same problem. After updating to 6.1.2 my iPad 3,2 will not find Verizon network. It just says "Searching..." for ever. Any thoughts?

I can't activate windows 8.1 pre-installed on my Toshiba E45-B4200 after BIOS Update

I bought Toshiba laptop Model E45-B4200, at first time I could activate windows 8.1 like a charm.
Few months later Windows 8.1 has crashed, so I did clean install of pre-installed windows, no problem so far. Toshiba Application installer app has downloaded BIOS update, so I ran it.
I tried to activate windows after BIOS update, but it didn`t work. No error message, but Change PC settings window just got minimized every time that I tried to click on Activate Windows option. I thought that I did some mistake, so I repeated windows reinstallation, and same problem occurred again.
Now I can`t update Windows, Office 2013, and so on.
I`ve tried SLUI 4 command to force activation by phone, but it didn`t work as well.
I read on MS blogs that windows 8.1 stores product key on MSDM table, windows should be activated normally. Now I got no options now, can you help me?

It shouldn't need to be activated it. Everything should be automatic. Because it's asking you, that's already indicative of a problem. You might want to call customer support.
- Peter

After bios update side nomberpad is not workinh keys from 0-9

Similar Messages

Maybe you are looking for