After upgrade cannot connect to router- Cisco Connect advises "unsupported operating system"
With the upgrade I am unable to connect to my Linksys E1200 Router.
When you try to login at http://192.168.1.1, what happens? What do you see on your browser? Does it say invalid password, or does it not give you a login prompt at all? And I'm not sure if you're problem is the wireless computer or the wired one...you say you have one wired computer, then you're saying that you use the same wire with the other one, and use the term "cables" so it's confusing what you're trying to do. Do you have two wired computers, one working on the internet and the other not? Or ???
Also, you can reset the router password to factory defaults by using the reset button on the back (press it for about 30 seconds, then release). This will also set all your configuration back to factory defaults, too, so you'll have to re-enter all your settings, but it is possible that you changed the password somewhere along the way and forgot what it is.
Similar Messages
-
After upgrading, cannot connect to the internet an...
I start to use BT Total Broadband Option 1 last monday and until last Thursday I got notified by email that the usage had been 7GB already after just a few days (out of the 10GB limit under option 1). Then I called on Saturday to upgrade the plan to option 2 which allows 40GB limit.
On Sunday midnight the original plan was cancelled. There were no internet from then on. Then on Monday night I got a text saying the changes requested to my service are now completed. However I failed to connect to the Broadband at home. The Home Hub's broadband signal keeps red in colour.
I have called on Tuesday night to ask for help. They will be contacting me again on Friday night after checks about the line.
May I ask if anyone have come across this problem ?? Are there any ways to get connected again ? because obviously the wireless network is there but it's just that I couldn't get connected to it. I suspect it's because the change of plan makes the login details different ?? It says that on http://bthomehub.home/ => Settings/Internet I should be able to connect without typing password if I'm an existing customer. However that doesn't work. I tried thousand times and am already very frustrated.
Hope someone can help me. Thanks a lot !Hi Vinc_bath,
Thanks for the posts and welcome to the forum.
I am sorry for the problem you are facing. DS is correct, changing your BT broadband options will not disconnect your service altogether. I will need to look into this for you to see what is going on.
Can you please drop me an email to [email protected], include your BT account details and the link to this thread.
Cheers
Sean
BTCare Community Manager
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry that we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-) -
Cisco Connect won't open due to Unsupported Operating System
I have a Mac with OS X version 10.7.4, however when I try to open Cisco Connect I get an error message that says:
Unsupported operating system
The router works with these operating systems:
- Mac OS X 10.4.9 or later
- Mac OS X 10.5.8 or later
- Mac OS X 10.6.1 or later
Please visit www.apple.com to upgrade your operating system.
Anyone know what I need to do to get it to open?I found this article, but I have device E2000, so does this mean I can't update my Cisco connect software? I just moved and my wireless isn't working. I need to get into cisco connect to set it up. Do I need to buy a new device?
Article ID: 23897
Older versions of Cisco Connect and the Network Magic add-on for Mac computers have compatibility issues with the latest release of Mac OS X (10.7 “Lion”). Only Cisco Connect versions 1.4.11222 and newer are compatible with the Lion operating system. To learn how to check your computer’s Mac OS X version, click here.
To ensure that Cisco Connect software can be installed on your Mac computer, check the table below which lists the devices that have this update.
Device
Compatibility with Mac OS X Lion
E1000
Not available
E1200
Download
E1500
Download
E1550
Download
E2000
Not available
E2100L
Not available
E2500
Download
E3000
Not available
E3200
Download
E4200
Download
EA2700
Download
EA3500
Download
EA4500
Download
X2000
Download
X3000
Download -
I'm trying to connect my MacBook Pro running on OS 10.8.2 to a Linksys EA3500 router and when I go to click on the set up icon I get an "unsupported operating system". Any suggestions on what to do? The Linksys site is useless. Do I need some kind of upgrade?
Don't use the CD software its not necessary.
Infact put it in the trash.
Your router will have an IP address in the range 192.168.1.1
Connect your router to your Mac via Ethernet cable (They usually supply one with the router and don't worry which end goes where the Mac LAN socket is bi-directional)
Also connect your router to your telephone line.
Now open your Web browser Safari . Type in the IP address above and a Javascript control panel will launch
Enter the default password and username (They are on a label on the router )
Your now have the ability to set up your router.
Your will need the password and user name supplied to you by your ISP at a minimum.
Enter these and most modern routers automatically configure the basic networking setting.
You now need to go to the security setting and set this as WPA2 Personal (NOT Enterprise) or WPA2 with AES and TKIP which ever it refers to and create a pass-phase. WRITE it down
You should be online.
Now remove the cable and connect to the Wifi and enter that passphase. -
I have the CANON REBEL T5 1200D, and when i connect it to my mac which is 10.10 the new OS X YOSEMITE it says that it "Cannot be used with this version of the operating system" why does it say that if my camera is listed under the supported digital cameras for OS X YOSEMITE?
Put simply, the minimum system requirements for iTunes have changed. You need a Mac running at least OS X 10.6.8.
It's best you look online to see if your model of Mac can be upgraded to at least 10.6.8 "Snow Leopard". It should still be possible to order a copy of Snow Leopard if so. -
Cannot connect to the phone system. An unidentified error has occurred, Please try again.
Issue: Lync 2013 users with remote call control enabled cannot connect to the phone system. When the user logs into Lync, they see an exclamation in the bottom right corner
with this error.
Error: Cannot connect to the phone system. An unidentified error has occurred, Please try again. If the problem continues, please contact your support team.
Environment:
1 site: Site1
2 Pools:
1. Lync 2010
Trusted application is added here for the site.
2. Lync 2013
Avaya phone system: AES r6-1-2-32-0
I have not moved the trusted application to the Lync 2013 pool yet, but my understanding is that it should still work since it’s in the site. Is my understanding on this correct? (All of my other trusted applications do work for Lync 2013
users & none of them have been moved yet. Remote Call Control is the only one that does not work.)
This is from the uccapi log. This is just from the user logging in, not actually making a call. Below are the items that I think are important, however, I don’t know how to interpret it to determine if the problem is on the Lync side or
the Avaya side. Here’s a summary:
SIP/2.0 100 Trying
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="E05700E2", snum="9", rspauth="f308eae87c0bbe64a1ab213574776cbdf9823ab6", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]>
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 INVITE
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0
SIP/2.0 200 OK
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="15C0F9A2", snum="13", rspauth="4fd891e39a33e902fb1cec5d980e5bf0ccb172a0", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]
>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]
>;tag=A7A45C856ECD79121A1827265ABBD7F6
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 CANCEL
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0
SIP/2.0 487 Request terminated
Authentication-Info: TLS-DSK qop="auth", opaque="5FD217E1", srand="F46EC133", snum="14", rspauth="1d92718caa4f61d967faa46a5c256aafa8b4e740", targetname="lync03.domain.com",
realm="SIP Communications Service", version=4
From: <sip:[email protected]
>;tag=bbb282ebbd;epid=a86d5b0a29
To: <sip:[email protected]
>;tag=A7A45C856ECD79121A1827265ABBD7F6
Call-ID: 9eb0d23a3b8f4e0eafc6c6da622fbecf
CSeq: 1 INVITE
Via: SIP/2.0/TLS 10.155.48.96:61472;ms-received-port=61472;ms-received-cid=1FA400
ms-diagnostics: 5002;reason="Request was cancelled";AppUri="http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent";source="lync03.
domain.com"
Server: http%3A%2F%2Fwww.microsoft.com%2FLCS%2FUdcAgent
Content-Length: 0Hi Suelizy,
To better understand the issue, I would like to collect the following information for troubleshooting:
1. Do you mean the Lync 2010 user can connect to the Phone System?
2. What’s next hop pool of the application?
In a mixed environment, you must set the next hop pool to be the Lync Server 2013 pool.
Best regards,
Eric -
Have situation on a unprotected wireless when accessing I cannot get a router address. I'm on system 10.6.8 on MacBook Pro summer 2009. Any thoughts on how to determine what's up?
You have basically verified that the issue is NOT with your MBP, but with this particular Wi-Fi network. Even though it may be unsecured, the provider may have elected to configure it for MAC filtering. In this case I am referring to the MAC (Media Access Control) address and not your Mac laptop itself. If this has been enabled, your Mac would only be able to connect if the Mac's MAC address was added to that filter.
-
after upgrading to NX-OS 5.04, out snmp traps monitoring system is not generating ticket / incident for the snmp traps and my question is whether we need to apply new MIBS for that?
Looking at the error message "The Network Adapter could not establish the connection" , It appears hostname and port may be incorrect. Review the targets.xml under E:\oracle\product\10.2.0\db_1\SAP_solman_SDB\emd and
emoms.properties under E:\oracle\product\10.2.0\db_1\SAP_solman_SDB\config folder to make sure host ( sap_solman) and port (1527) are correct.
As far as setting the environment variables goes, you can go to control panel -> system -> advanced -> environment variables and set the ORACLE_HOME and ORACLE_SID
-Ramesh -
Info about Cisco Fabric Interconnect 6140 Operating System
Hello. We're looking for tech specs about Cisco Fabric Interconnect 6140 Operating System. For us is important to know if the os is NX-OS or not.
Posted by WebUser Federica RossiThe underlying OS is built on NX-OS, but there is a lot of software running on top that is the actual UCSM itself.
The UCSM software controls the NXOS portions directly - there is no ability to actually configure the system from an NXOS level.
UCS-250-A(nxos)# sh ver
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Software
BIOS: version 1.5.0
loader: version N/A
kickstart: version 5.0(3)N2(2.1m)
system: version 5.0(3)N2(2.1m) -
How to install Deskjet 3055a, new router but unsupported operating system on Macbook
Hi,<br><br>Please go easy with me, I really know very little about all this !<br>We have a Deskjet 3055A printer which has been linked wirelessly to my iPad and a MacBook without a problem until now.<br>We have installed a new router. I am thinking that we have to amend our network in some way ?<br>I have tried to run the HP cd on the MacBook to amend it, but all I get is the message as follows...<br>"Unsupported operating system. The installer is not compatible with the version of the operating system on your computer. It is compatible only with 10.6 and below." <br>The MacBook is running OS X version 10.9.5<br>Any help greatly appreciated - thank you ! ( Please keep it simple !! )<br>We<br><br>
Welcome to the community @Teekayk
I understand you are trying to install your Deskjet 3055A on your Mac, running Mavericks. The installation CD may be compatible up to 10.6, and that could be why you are seeing the error message.
This link should help you. It will show you how to install the printer on your Mac. There is no full driver and software available for the Deskjet 3055A on Mavericks, which basically means you will need to review your other options to scan on your Mac through Apple Updates, which is all included in the guide.
OS X v10.9 Mavericks: Installing and Using the Printer on a Mac
Have a great weekend, I hope the information helps you
R a i n b o w 7000I work on behalf of HP
Click the “Kudos Thumbs Up" at the bottom of this post to say
“Thanks” for helping!
Click “Accept as Solution” if you feel my post solved your issue, it will help others find the solution! -
After OS4 upgrade cannot connect to iTunes Store???
Hey guys,
I upgraded my 3GS software to OS4 and since then I am unable to connect to the itunes store from my phone. I can connect to the internet using Safari and i can access the store when I connect my phone to my laptop. But when i try to connect to itunes store just from my phone through wireless, it just says "Cannot connect to itunes store".
My internet connection/Wifi is super, there are no problems there.
Pls help me out with this glitch. Its annoying!
Thanks a ton!I think this might have something to do with using 2 iPhones on 1 computer. My boyfriend and I each bought an iPhone 4 yesterday - mine works fine (I was the first to connect to iTunes). My boyfriend connected his to iTunes after me, then when he disconnected from the computer and tried to access the iTunes store through wifi it came up with the "cannot connect to iTunes store" message on his iPhone.
I created a new user on our laptop and downloaded iTunes again. I connected my boyfriend's iPhone and restored to factory settings and this seemed to do the trick!!!! Hope this helps! -
hello iupgrade ipad to ios7 after the upgration not conect to wifi and shows the message connot able to connect i do every things that i read on apple forum but at this moment cannot connect to wifi my wifi modem is tp link
You are in Recovery Mode. Follow the instructions below to recover your iPad.
1. Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
2. Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to turn off.
If you cannot turn off the device using the slider, press and hold the Sleep/Wake and Home buttons at the same time. When the device turns off, release the Sleep/Wake and Home buttons.
3. While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
4. Continue holding the Home button until you see the "Connect to iTunes" screen. When this screen appears, release the Home button.
5. iTunes should alert you that it has detected a device in recovery mode. Click OK, and then click Restore to restore the device.
Note: You need to be patient and repeat the above many times to recover your iPad. Data will be lost. -
After restore-cannot connect to voicemail-call AT&T?!?
Help I restored my iPhone and now it says cannot connect to voicemail! It doesn't even tell me to call visual?
I had to restore my iPhone last night and discovered the same problem today with my voicemail. In a ditch effort to fix the problem without calling att (afterall, the call center closes after 6pm eastern on Saturday and does not reopen until Monday morning) I tried by calling my voicemail. Here are the step to do that:
1. Dial your 10digit phone number from your iPhone. Then press call.
2. You should hear your voicemail pick up at which time you need to push the * key
3. After you push the *
You may then be prompted to enter your voicemail password, if so, go ahead and enter it. If not, then you should be able to hear all of your voicemail messages that are on the AT&T system, not what on your phone.
4. Go ahead and hang up.
5. Go ahead and try to look at your voicemail.
6. It should be able to connect and ask for the passcode.
It worked for me, hopefully it will work for you.
These are the same step you would use to access your voicemail from another phone other than your cell phone.
***Remember that they always say you should press and hold the "1" unitl it dials your voicemail, but that does not work on the iPhone as it does not support one-touch dialing and it already has visual voicemail. -
New ipad after ios6 cannot connect to itunes store
After updating to ios 6 error shows "cannot connect to itunes store."
The Complete Guide to Using the iTunes Store
http://www.ilounge.com/index.php/articles/comments/the-complete-guide-to-using-t he-itunes-store/
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
iTunes: Advanced iTunes Store troubleshooting
http://support.apple.com/kb/TS3297
This works for some users. Not sure why.
Go to Settings>General>Date and Time> Set Automatically>Off. Set the date ahead by about a year.Then see if you can connect to the store.
Cheers, Tom -
G only access after upgrading to WRVS440N wireless router
I am using a WUSB54GP wireless adapter.
I was using a WRT54S wireless router.
Both worked great together.
Now that I upgraded to a WRVS440N router, I have to set it to G-only in the
Wireless
Basic Wireless Settings page
in order to connect.
Using the B/G/N mixed settings does not allow me to connect.
FIrmware updated on the WVRS4400N to 1.1.03. No firmware update available for the WUSB54GP.
Reinstalled drivers for Windows XP Pro SP2 using the WUSB54GP.
So far no luck.
Suggestions?In the non-working computer, temporarily turn off your software firewall, including Windows Firewall, and see if that helps.
In the router, since the last firmware upgrade, have you reset the router to factory defaults, then setup the router again from scratch? If not, then please do this and see if it corrects your problem. If you saved a router configuration file, DO NOT use it.
Message Edited by toomanydonuts on 05-04-2008 05:54 AM
Maybe you are looking for
-
Placeholder or User Parameter receiving directly from a field.
I can place as well placeholder as much as user parameter inputs in my report. My issue is when query returns no rows, but I need to show in this case user input datas, and my variable(placeholder or user parameter) is just syncronized with user inpu
-
One who need to initiate BI Publisher should follow this link. http://oraclelabs.com/index.php/2010/10/11/creating-new-report-using-bi-publisher/ Good post to do it from scratch Regards
-
Can no longer print to ethernet printer on Airport Extreme network
I have a Mac/Windows home network with two airport extreme base stations. One is connected to my dsl modem. The other is used wirelessly to extend the network, and I have a Xerox Phaser 5500 connected to one of its lan ports. Until recently, all comp
-
JCBC Adapter and File adapter not processing messages
Hi I noticed that messages are being delivered to Adapter engine and the same are visible in Runtime Workbench with status "to be delivered". But, JDBC Adapter and File Adapter not processing these messages. Any idea where I can find the problem? I w
-
I currently have a toshiba ext. Dr with my cataloges. I purchased a 2T WD essentials and formatted for Mac Lion and cloned my existing drive to it. what is the procedure to have Lr recognize the new drive? I tried giving it the same name as the exist