Airport Express Stops working when broadcast is turned off

Router: Linksys WRT54G version 2
Using: Airport Express
Purpose of Airport Express: To enable wireless speakers.
After a lot of trouble with the router and eventually having to update all router firmware, changing the type of security the router was working, etc I finally have the router up and running.
Everything is working fine but the last step I'd like to do is not have my SSID broadcast. As soon as I stop broadcasting the network the extreme loses it's connection.
The audio bridge I used before (Sondigo) hasn't updated it's drivers for windows 7 in months so I switched to the airport express but the audio bridge didn't need the SSID to be broadcast to work once it was connected to the wireless network.
Is it possible to have the SSID NOT broadcast and the extreme to continue to extend + broadcast the wireless speakers?
Thanks!

Welcome to the discussion area, Carl M!
You'll enhance your chances of the AirPort Express joining the hidden Linksys network if you "hard reset" the AirPort Express by holding in the reset button until the amber light blinks more quickly, then release.
Configure the Express again to "join" your Linksys wireless network. Since the network will not appear as a choice to join, you'll have to type in the exact name of your network, security and password to give the Express the best chance to connect.
This procedure will sometimes work, sometimes not. Might be worth a try.
Message was edited by: Bob Timmons

Similar Messages

Airport Express Stopped Working when I switched to FIOS wireless router

AirPort Express worked for several years with Linksys router. When I upgraded to FIOS service, it came with a new wireless router. I have two Macs (iMac-G5 and MacBook 2.0 GHz) and work-supplied Lenovo T-61. Network is set up with WPA2 with 23-character-long pass phrase. AE (802.11B/G) will not connect to network. I can reset it to factory defaults and Airport Utility will find it. I then change the wireless interface on iMac to match the default network and I can configure the AE. When I apply the configuration changes, the AE reboots and never comes on-line. It stays in either the blinking orange pattern or in the alternate between orange and green pattern.
I have tried setting the AE up manually as well as "automatically" and have not had any success. I was a network engineer for over 10 years, so I have lots of experience configuring IP routing and switching. The log files on the FIOS router do not show any attempts by the AE to connect to my LAN.
Does anyone have any suggestions?

Suspecting a problem with the security key, I began to experiment with different security settings. My first attempt was to change the security setting on the Verizon router from WPA2 to WPA. I did not change the key. When I did, I was able to configure the AirPort Express and then get the Airport Express to reboot and establish wireless communications with the FIOS router. Again, the only change I made was to switch the encryption type on the FIOS router from WPA2 to WPA. I have no idea why the AirPort Express would not properly join the network when the main wireless access point (the FIOS router) was using WPA2 security.

Airport Express stopped working...

My airport express stopped working some time ago so I bought a new one so I could play my music remotely again. My ld one just "disappeared" , it no longer showed on iTunes. I am having problems setting the new one up. I am using airport utilities and going through all the prompts. It is making me join my existing wireless network. At the end when it goes to restart, I get an error message "Airport utility was unable to find your Apple wireless device after restarting".
I am stuck, any suggestions?

Quick check list
Is your AE firmware updated to 7.3.2?
Is your OS 10.5.4?
Is your Airport Utility software 5.3.2?
What are you using for a wireless base station? is it a combo modem / router, or are you using an Apple Extreme Base Station in bridge mode with a third party router?
All of the above are possible issues.
Provide some more detail in your post and the group will be more likely to be able to help
Cheers

Why does AirPort Extreme stop working when I plug in a USB hard drive?

Why does Airport Extreme stop working when I plug in a USB hard drive? The USB drive has its own power supply. I've tried isolating the hard drive from Airport using a powered USB hub to no avail.

The USB port on the AirPort Extreme is borderline as far as its ability to supply adequate power to a hard drive. Another way of saying the same thing is that this is not a high power USB port, like you would find on a computer.
Your 2TB drive likely requires a bit more current than the USB port on the AirPort Extreme can supply. It is also possible that the drive's firmware may not support a network USB connection....only a "local" connection to a computer. Check with Seagate support on that possibility.
Try using a powered USB hub with the 2TB drive....and make sure that the drive is formatted correctly in Mac OS Extended (Journaled) or FAT32....which the AirPort Extreme USB port can accept.

Airport Express Stops Working

Dear All, My Airport Express just stopped working. I tried to reset it (while plugged in, use a pin to punch the reset hole) but the amber light keeps blinking. Is this normal? Or have I done anything wrong? I truly appreciate your input.
Jimmy Chiu

A persistent, flashing amber light indicates that any of the several potential conditions may require your attention:
o The base station has not yet been configured because it is new, or the reset switch has been set.
o You have selected a security configuration that is not recommended.
o One of several other conditions, such as a disconnected Ethernet cable or invalid IP address has been detected.
(ref: http://docs.info.apple.com/article.html?artnum=305101)
If you run the AirPort Utility, it will show an amber circle on the summary page next to the area(s) causing the problem. Click on this amber circle and it should provide an explanation.

Airport Express not working when used with Broadband Router **HELP!!!**

Hello.
I have an ethernet network in my house, and I am connected to the network via a Linksys router for Broadband VOIP and internet. I am on a G5 in my home office and want to stream music to my Airport Express for my home stereo in the living room, via the ethernet connection.
The problem is that when using the router in my network, only the Admin Utility sees the base station-- iTunes does not.
If I remove the router from the equation altogether and plug the network ethernet cable directly into the G5, the AX in the other room works just fine and I can get internet on the G5 in the office. The problem is that I need the router to operate my Vonage VOIP phone service and to connect a second computer to the internet as well. The IP address for the router in the home office is "192.168.x.xxx" and when I try moving it to the living room and connecting the AX to it, the Admin Asst doesn't see the AX at all.
When I connect the router to the network in the office, I can use internet on both computers and the VOIP phone service, and the AX Admin Asst. sees the base station from the other room. But again, iTunes does not.
Is there a way to configure the router to see the AX?
Thanks for your help!

Forgive me if this a little off thread, but I have just managed to get this to work and thought it might help people with similar configuration issues (mix manufacturer wireless networks)
I received an Airport Express (FW v. 6.3) for Christmas this year. I already am using a D-Link DI-524 wireless(G) router (Rev A FW 1.03) for my Comcast cable modem in my house (downstairs). What I wanted to do is to add the Airport Express in my office upstairs to my network (client mode) so that I could print from my HP Deskjet 3740 printer and listen to iTunes on my stereo through Airtunes. I have two iBooks (G3) with regular (802.11b) airport cards in them) running Tiger.
I ran into a couple of snags though. I could see the printer in Rendezvou and I could see the airport express in iTunes. I however could not print to the printer or connect to the speakers. I was able to connect to the speakers very intermittenly and then the audio would be disrupted every few seconds.
After a bit of hacking, what I found is that it seems that WPA PSK security doesn't work between the two. I changed the security to 128 bit WEP (ASCII mode). This means that you need an exactly 13 character pass phrase. This is necessary because Apple (and pretty much only Apple) supports 40 bit WEP (5 chars) and D-Link (and the rest of the Windows wireless universe) supports 64 bit WEP (7 chars), but they both support 128 bit WEP. I assume you could set both up as an open network if you were far enough from your neighbors, but I am in a townhouse complex, so I thought I probably better have some security on the network.
Now I only see one network (the one set up on my D-Link router) and I can print to my printer and stream to my stereo through iTunes (without disruption). Seems to work seemlessly now.
I should also mention that I did about three other things. I moved the LAN subnet on the D-link router to 192.168.1.1 (DHCP client address are now between 1.100 and .1.200) I had heard that this was necessary since both routers tried to use the 192.168.0 subnet, but I think this is only necessary in relay mode. I also statically assigned the IP address for the Airport Express. Finally I set up a firewall rule of Source WAN/LAN IP addresses of 192.168.1.100-200 of any protocol from ports 1-20000 to the same destination address range should be allowed to allow for all LAN traffic to be passed. I am very certain this is unnecessary and possible dangerous for security, but I thought I should mention that I did it.
Hope this might help someone.
Michael
iBook G3 (600 MHz) Mac OS X (10.4.3) D-Link DI-524 Router. Motorola Surfboard Cable Modem. Comcast Broadband

Had a Airport Express connected to my stereo and it was working. I brought an Airport Extreme and suddenly it took over and Airport Express stopped working and disappeared from Airport Utility. What I am supposed to do? ar2ro

I have an Airport Express connected to my stereo and it was working without any problem.
Recently I bought an Airport Extreme to use it as my Base Unit connecting it to my DSL.
I followed the instructions of the Airport Utility, and it started working.
Suddenly, problems started happen the Airport express that was connected to the stereo , stopped working and it disappeared from the Airport Utility area , as it did not exist in the network. I tried to reset it but it did not appear in the Airport Utility page.
Apparently I have other problems with the private network that it created because I cannot use it because of problems with the password that was created. I can only use the network that I created for my guest...
I dont know if my problem is a configuration problem or there is problem with the equipment.
I read that other users where having the same problem with the Airport express , using non apple equipment as their base unit , but I thought that using the Airport Extreme was going to be compatible and no problems would happen.
What should I do?

Common Problem. Common solution.
Connect your Express via ethernet cable to the Mac while other network connections on the Mac are switched OFF.
After the Express shows up, change the settings of the Express to join the existing network. Take the appr. settings.
Unplug and reconnect your Mac to the network.
Check if the Express shows up in Airport Utility
Alternative solution:
Hardreset the Express to factory settings
(while on power push the Pin next to the audio plug with a paperclip. Plug out the Express still holding down the little button then replug the Express to power and release button)
After that, the Express will show up in the Airport Utility.
Make all needed settings.
I would prefer the first solution, its easier just to plug a cat5 cable.

My ipod has stopped working since the laptop turned off during synching.it shows no music and wont play games also is slower,constantly resets and freezes itunes when connected to computer.if i switch it off a spinning wheel appears till batt dies.help?

My Ipod has stopped working properly since the laptop shut down during synching.
My ipod is being slower and wont show any music. when I go into general settings it says the music and videos are loading..
It wont let me into settings all of the time either.
My applications and games have become slow or unresponsive.
The ipod keeps resetting itself, I have tried resetting it to no avail.
I tried plugging it into itunes but it freezes itunes and wont show up on my computer.
When I switch off the ipod it shows a spinning wheel until the battery dies, which could be nearly 2 hours!!
does anyone have any advice as to what to do?
currently ive reset it - nothing has happened
ive let the battery drain itself then recharged it to see if that would make a difference - no difference
Help ASAP needed

Try restoring the iPod via iTunes. First from backup and if problem persists, restore to factory defaults/new iPod.
If still problem make an appointment at the Genius Bar of an Apple store. If your iPod is with in the one-year warrranty, not abused and defective Apple will replace it.

7th gen Nano only works when plugged in, turns off when unplugged... battery is fully charged.

7th gen Nano only works when plugged into computer, as soon as I unplug it shuts off (it was ejected from iTunes). Battery is fully charged. Have already done a restore in iTunes and checked for updated software.

Hello there, DizDude.
The following Knowledge Base article offers up some good recommendations for troubleshooting battery issues with the 7th generation iPod Nano:
iPod nano (7th generation): Hardware troubleshooting
http://support.apple.com/kb/TS4433
Particularly this section:
Battery life appears short
Learn how to conserve battery life.
Ensure that the latest software is installed on the iPod.
When charging, use the cable that came with iPod nano (7th generation) and leave the device connected until it is fully charged.
Note: If you are charging using your computer, don't connect iPod nano (7th generation) to your keyboard. Also, the computer must be turned on and not in sleep or standby mode. If iPod nano (7th generation) is connected to a computer that's not turned on or is in sleep or standby mode, the iPod nano (7th generation) battery may drain.
When you are done using the iPod nano, verify that:
The Radio application is off (tap the button)
Music is paused (tap the button in the iPod application or disconnect the earphones)
There is no active Pedometer session (tap the Stop button in the Fitness application)
Dimming the screen is another way to extend battery life on iPod nano. Go to Settings > General > Brightness and restore the brightness to the default, or drag the slider to the left to lower the default screen brightness.
Playing tracks with EQ requires your iPod processor to consume more energy than playing tracks without EQ, because the EQ information is not encoded in the song. To prolong battery life, turn EQ off if you don't use it. Go to Settings > Music > EQ and select Off from the list. Note, however, that if you've added EQ to tracks in iTunes, you'll need to set EQ to Flat to have the effect of Off, because iPod keeps your iTunes settings intact.
Try restoring iPod nano (7th generation) by connecting it to iTunes and clicking Restore.
Test the battery life.
Issue not resolved
If the issue is still not resolved, please read this information on servicing your iPod.
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Why is my music stop playing when the backlight turns off?

Hi I got a new iPod classic about 2 months ago and now every time the backlight turns off it stops playing music. Can somebody help me because the only solution I found was to put my backlight to ''always on''

This is usually a sign that your headphones are not plugged all the way in. Make sure the white part of the headset is flush with the body of the Nano and no silver from the plug can still be seen.
If you are 100% positive that the earbuds are all the way in, double check to make sure the headphone jack is clean and clear of debris and/or damage.
B-rock

Airport Express stopped working with my Airport Extreme Network

Hi. I have an airport extreme as my base station and I have an express that is used to extend the network and plug into my stereo to allow for streaming music from iTunes. The system has worked great for months and now suddenly the extreme dropped. The light used to be solid green but now its yellow. I've reset the express to factory settings and now its blinking yellow. I can't figure out how to get it back online. Any help would be appreciated. It seems like an airport utility program could do this but I can't seem to find it on my Macbook Pro.
Tim

Sorry...I meant to say that the express dropped. The extreme still works fine and gives me good internet connectivity.

HT2508 airport Express not working in Mountain Lion

My old airport express stopped working properly since I loaded Mountain Lion. I purchased a new Airport Express and it will work, but the audio fades in and out. I am connected from the airport express unit to my audio receiver via a 3.5 out into RCA (red/white) connector into the receiver. Can someone suggest a cure?

I have three printers up and running connected to an Air Port Express,
and since I upgraded to Lion I can't connect to any of them, so I continued using SL on this MBP17.
System Preferences does not show any of my printers.
I opened Air Port and it says I need to update.
When I click on the update button, it takes me to the App Store, but no Air Port Software — What gives?
Now having the same problems with Mountain Lion.
Hoped ML would fix the problem, but NO.
I find I have to save documents to a flash drive and go to my old PowerMac G4 to print.
Steve we miss you. Apple is going to crap without you.
Message was edited by: random47 to fix typos and add information.

Airport express: wireless works, but internet does not

Hello.
It happened yesterday for no apparent reason: Internet was not working via airport anymore, as it should have normally.
Config: Cable modem to Airport extreme (.g); USB printer attached to base station, base station Ethernet port going to router with Boradband phone and 1 PC attached to it.
4 MAc computers attached to Network (and getting Internet) via Airport.
Internet connection using DHCP, dynamic IP address provided by RoadRunner (Time Warner).
I tested Cable Modem (works), all ethernet cables (good), reset base station and recreated an airport network.
Airpot network works, USB printer is accessible via Airport, but Internet is still off (although Network Configuration in Sys Pref give me a green light and informs me that I am connected to the internet)
My question: is it possible that Base Station fails only for its Internet/WAN capability, and not for Network functions?
thanks. This one is a puzzler.
Paul

Hello.
We have been having the same problem discussed in this thread earlier, described as follows:
It happened two days ago for no apparent reason:
Internet was not working via Airport Express anymore, as it
should have normally.
Config: Cable modem to Airport Express via a US Robotics router,
2 MAC computers (iMac700 and MacMini) attached to Network (and getting
Internet), the iMac through router and the MacMini via Airport Express.
Internet connection using DHCP, dynamic IP address
provided by RoadRunner (Time Warner).
iMac connected to router is getting Internet just fine; MacMini connected to network via AEX is getting network signal but no Internet. Network diagnostics says it can't tell what's wrong and call ISP. ISP says it's an Apple problem.
I tested Cable Modem (works), all ethernet cables
(good), Airport Express network works, but Internet is still off for MacMini.
I've done a power recycling exercise twice, but still no Internet on the MacMini.
Does anyone have any ideas? Both my son and I are stumped. He's a teenager and is fairly computer savvy. Neither of us has been able to figure this out.
Joe

HT4587 I downloaded Airport Express Utility 5.6 to get my Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility.

I downloaded and installed Airport Express Utility 5.6 to get my old Airport Express to work with the latest Mac OSX 10.7.4, but when I install and run it, it still says my Airport Express is out-of-date and needs the 5.6 utility. What's up?

It is likely that you downloaded AirPort Utility 5.6.1. If you checked the requirements, this only runs on Leopard or Snow Leopard Macs.
You have Lion, so you need AirPort Utility 5.6 for Mac OS X Lion

IPod touch stopped working when charging now won't turn on at all

iPod touch stopped working when charging now won't turn on at all

Try in order:
- After charging or half an hour, reset the iPod:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Connect the iPod to the computer and if it shows in iTunes, restore the iPod via iTunes.
- See if placing the iPod in recovory mode will allow iTunes to see the iPod so you can restore the iPod. For recovery mode see:
iPhone and iPod touch: Unable to update or restore
- Make an appointment at the Genius Bar of an Apple store since you likely have a hardware problem.

Airport Express Stops working when broadcast is turned off

Similar Messages

Maybe you are looking for