AirPort Express with PC -- Setup Problems

Hi
Just wanted to share my experience -- I wasted most of a day getting my AirPort Express network up. Problem was, the setup software assumes that you have a wireless card in your PC. If, like me, you have a simple ethernet connection to a wireless router, then the program apparently has no way of finding the AirPort Express.
After hours of fumbling with suggestions on this forum, I finally found the tech support number and we figured out that I needed to run the setup program on my laptop, which does have a wireless card.
I would STRONGLY encourage Apple to re-write its setup software to recognize this very common hardware configuration and work with it, lest more customers waste more of their time. I was THIS CLOSE to angrily returning the box. Now that it's up, I really love it, but I almost didn't get there.
AirPort Express Windows XP No wireless card -- ethernet connection to wireless router
Airport Express Windows XP No wireless card -- ethernet connection to wireless router

I had the same problem as you did with the setup of the AX from a PC connected to the router by Ethernet. I was able to run the setup by using the "Other ..." button at the bottom of the Base Station Chooser and giving it the IP address of the AX.
Does iTunes on the PC connected to the router by Ethernet find the AX? It doesn't for me. It works great from my other 3 PCs that are connected to the network by wireless. Of course, the PC with the problem is the one across the family room from the stereo ...

Similar Messages

Airport Express Base Station Setup problem

My new Airport Express Base Station (2nd generation) does not sense the internet using an ethernet cable. The status light is green. I am using a hotel's DSL system in Brazil. When using the same cable, and connecting my laptop directly to the system, it senses the internet just fine, so I know it isn't the cable or the hotel. Does anyone know of compatibility problems with this Airport model?

Does the DSL service require PPPoE for authentication before allowing you Internet access? If so, then the device directly connected to the DSL modem would need to be configured as such.

Airport Express & Apple TV Setup Problems

I am having some strange problems with my network. First, I reset my Airport Express and went through the steps of connecting it to stream music, however, the Airport Utility will not recognize it after restarting (I can do a hard reset and it will find the unit, but then hangs up over and over at the same point).
Also, at the same time, my Apple TV is showing in iTunes, can stream music and movies, but is not showing in the Airport Utility and will not sync.
I am not sure what I might have changed...any ideas

I am on 10.5.8. When I do a hard reset the airport Express, the computer finds it, however, after going through the steps to add it to my network to stream iTunes, it restarts and the computer can't find it (light continuously blinks amber).
The AppleTV is showing in my iTunes, but NOT in my list of wireless devices and it won't sync. So it does stream movies and music, just won't sync. When I try and sync it, I get a firewall error, but I have my firewall settings to allow all incoming devices.
Should I just reset everything and try and start over?

Airport Express with Extreme

Grettings,
I have recently purchased an Airport Express with the desire to extend the range of my wireless home network. I have had no problems with the Airport Extreme (other than litmited signal coverage) but I can't seem to setup the Express to save my life. Here's what I've got:
-I plug the Express into the wall, the status light goes from green to amber to flashing amber.
-Airport Admin detects the Express but cannot communicate with it.
-I cannot update the firmware because the updater cannot communicate with the Express.
In my past expereinces with Mac products setup processes have been so simple that I'm a bit confounded by my inability to get this up and running. Is something wrong? What do I need to do?
Thank you, in advance, for your assistance!
Andrew
powerbook g4 Mac OS X (10.4.8) imac snow g4

"Factory default" reset the AX
- (ref: http://docs.info.apple.com/article.html?artnum=108044)
Set up a Wireless Distribution System (WDS)
(Note: To facilitate setting up the base stations, place them in near proximity of each other during the set up phase.)
Set up the AirPort Extreme Base Station (AEBS) as the WDS Main Base Station, by connecting directly, using an Ethernet cable, to the LAN port of the AEBS, and then use the AirPort Admin Utility, located in /Applications/Utilities, to make the following settings.
WDS Tab
- Enable this base station as a WDS: main base station (checked)
- Enable wireless clients on this base station (optional)
- Click "+" to add Remote/Relay Base Stations.
-- Select the Base Station that you want to be the WDS Remote/Relay.
-- AirPort ID: <verify that this is the correct wireless MAC address for the Base Station you are adding as a Remote/Relay.
-- Auto configure as a WDS remote base station (checked)
-- Click "OK."
- Verify that the Remote/Relay Base Station has been added to the list.
- Click "Update," and then verify the settings for the Remote/Relay.
-- Allow wireless clients on this base station (checked)
-- New network name: <verify that this is the same as the network name for the AEBS>
-- TCP/IP: Configure using DHCP
-- Base Station Password: <the Remote/Relay Base Station password>
-- Confirm: <same as previous step>
-- Click "OK."

Apple AirPort Express with Airtunes and Netgear WPN824v2 Router

I'm having some trouble getting the AirPort Express with Airtunes to connect to a Netgear WPN824v2 network.
Details:
- Router: Netgear RangeMax Wireless Router WPN824v2
- Wireless Network Security: WEP
- Computer: MacBook Pro
- OS: OS X 10.4.10
- AirPort card in computer: this works fine - no problems
- AirPort Express with Airtunes: the setup routine goes OK, but then the unit cannot connect to the wireless network; the light blinks amber.
Could the problem relate to the password (Hex versus ASCII) or perhaps WEP versus WPA?
Any / all suggestions welcome. Thanks.

sonicdubster, Welcome to the discussion area!
Are you following the directions in KB 302153, AirPort Express: How to join an existing wireless network in client mode?
Is the AirPort Express (AX) placed in an area where it can receive a good wireless signal from the Netgear?
Does the AX connect if you disable wireless encryption?
WPA (or WPA2) is much more secure and less troublesome than WEP. If all of your equipment supports WPA, I would switch to WPA.

Air Port in my Imac and Airport Express with my 360

Hi all,
Not sure if Im being nieve but I am trying to set up a network between my Imac and an airport express, with the ulitmate goal of connecting my Xbox 360 to that network. My imac has an airport card and Ihave tried doing the WDS setup any help that any one can offer would be great.
Thanks

G'day Duane,
Just clarifying things here, is it still possible to connect a 360 (via MS' networking adaptor) to a wireless network created by an iMac's built-in airport? Currently I'm using a network encrypted by a WEP password which works all fine and dandy with my MacBook. On the 360, it recognises the network, allows me to enter the password and connects, only to tell me when testing the XBL connection that the wireless network is not connected. The same problem happened when I took off the security. Is there a way around this apart from connecting an ethernet cable to my MacBook/directly into the router?
Cheers in advance,
-Tom

Trying to set up Airport Express with Ethernet Powerline adapters

Hello,
Having some problems trying to set up my Airport Express with Netgear ethernet powerline adapters.
I want to set up as follows:
Wireless Belkin router --- powerline <---> powerline --- airport express --- home stereo system
The problem I have is that I can connect the airport x in client mode & wirelessly play music using airtunes (until the sound breaks up) but itunes does not find the airport x when connected via the powerlines.
I have airport admin utility configured as follows:
Airport tab:
Wireless mode: create a wireless network
Wireless network name: same as my wireless router SSID
Allow this network to be extended: unticked
radio mode: 802.11n (802.11b/g compatible)
Channel: automatic
Wireless Security: WPA/WPA2 personal (as per my router)
Wireless Password: as per my router
Verify Password: as per my router
Internet tab:
Connect using: ethernet
Connection sharing: off (bridge mode)
Music tab:
Enable Air Tunes ticket
no password set
In iTunes, I have home sharing on & share entire library selected with no password set.
Using OS 10.6.5 & Airport Express 7.5.2
I can ping the IP address of the airport express when connected via the powerlines but cannot select the speakers in iTunes (they are greyed out).
Any assistance would be appreciated....
Thanks

Hi,
Thanks for the quick response...
As suggested, I connected up the Airport X to the Belkin and plugged in a pair of headphones. It didn't work, still could not select the Airport X as speakers.
Dug out my old Netgear DG834G and connected that up in place of the Belkin - it worked. Next connected in the Netgear powerlines and it still worked.
So, the problem is the relatively new Belkin F7D4401 router.
Looks like I will have to find an alternative 802.11n...
Thanks for your help.
Regards
Simon

Replacing an Airport Express with a Time Capsule but it won't connect to the internet.

Hello, I hope somebody can help.
I am trying to replace an Airport Express with a 2TB Time Capsule but it won't connect to the internet, via an ADSL modem.
I have tried everything I can think of, powering down all devices, re-setting all devices, but nothing seems to solve the problem.
When I first tried to set up the Time Capsule, there was an option to replace the Airport Express using the same settings.
But there were repeated error messages of 'No DNS Servers' and 'PPPoE server couldn't be found'.
I also had messages that the password for PPPoE wasn't correct, but when I plug the Airport Express back in again, everything works fine.
What could the problem be?

99% of issues with authentication are wrong password or wrong username.. eg it can be strange like the user name is missing the domain.. whereas the Airport Express works fine without it.
Ring your ISP and make doubly sure you have exactly the correct username and password.
If it still doesn't work, put the adsl modem back into router mode and try it again directly on the modem.. if it works ok on the modem but fails on the TC that is possible and can be caused by pppoe client using incorrect authentication type, CHAP or PAP which the TC does not allow you to select AFAIK.. some ISP do not give enough time to get the router to switch on auto to the correct authentication method.
In the end run the modem as router and bridge the TC. It will work just as well for most installations in bridge as the modem in bridge.

Airport Express with printer & hard drive with Time Machine

I have a MacBook that I'd like to backup its data. Concerned about the following (in level of concern from highest to lowest): theft, crash, fire.
I currently have an Airport Express with a Brother printer attached to it that my PC and MacBook print to.
I am really in a dilemma as to what to do. I was looking into Carbonite to get an offsite backup location of my data. (I figured offsite would cover all concerns of losing data due to theft, fire, or just a crash) However, Carbonite does not hold onto data you delete (ie, my photos and videos will fill up my hard drive eventually and I'd like to just archive them in one central spot when I am done accessing them on a regular basis-- ie delete them off my MacBook hard drive). That is like $55/year to do Carbonite... but, the only thing that will help me with over a hard drive in my house is a fire (and theft if a burglar were to find where my backup drive was in the house).-- Of course, I'd probably want a different location for my hard drive for that reason -- so, I'd have to buy another airport or just a time machine that has the wifi built in.
I've read lots of issues with the Western Digital trying to download programs onto your computer... I have one for my PC that I backed up photos manually and it did try to install programs when I attached it to my PC... not so much my Mac when I took some photos off it. I looked into getting another portable hard drive at Costco for my Mac, but realized that it would require reformatting to use on my Mac (as it was built for a PC).... something I wasn't sure if I was computer-savvy enough to do or if I did do it, would I end up with issues later on?
Anyhow... in the end, what do you all do to backup your data, especially photos and videos? Do you have smaller hard drives that you back up to and then when full move them to an offsite location? Can you have more than one "hard drive" backing up..... I was thinking it would be nice to have one larger hard drive that would potentially hold all my photos and videos so I can access anytime, but then have smaller drives of the same data that I can take to a safe deposit box and use as my super secure backup (no fire, no theft, no crash).
btw, When doing time machine, does it keep all the metadata with each photo?
Burning CD's is time consuming.... and, I have heard there are different qualities of disks out there... archival v. not... how long do the archival last v. the non-archival... or is that more of an issue for future generations not being able to access our photos?

You need to remember that the Time Capsule is both a wireless router and a hard drive all in one enclosure. If you don't need a wireless router, around $150 of the $300 for a Time Capsule is going to be in the router portion of the device.
The nice thing about the Time Capsule is that it is a network drive. All Macs running Leopard or Snow Leopard will be able to back up automatically to a single device. The first generation of Time Capsules about two years ago had some power supply problems that affected some users. Apple announced a program for these users to replace their Time Capsules.
So, it depends on your requirements. If you are looking for a new, dual band wireless router and want to backup your Macs running Leopard or Snow Leopard automatically using ethernet or wireless, the Time Capsule is a logical choice.
If you don't need a new router, then you'll need to look at a separate hard drive that will be attached directly to the computer using the USB or FireWire port. If you have two Macs, you'll have to get two hard drives if you want to do Time Machine backups correctly.
Most hard drives can be reformatted to work with Mac if you don't mind a few extra steps and Disk Utility (Macintosh HD > Applications > Utilities > Disk Utility) does not look too complicated for you.
Message was edited by: Bob Timmons

Configure airport express with mac book air

I am trying to configure airport express with a Mac Book Air, without success; the program is installed, but then, nothing appears to configure Airpor Express...
Can I get any help? Thank you
António

Hello!
I´m sorry it took so long to reply, but I´m new to these blogs; and I´ve been travelling a lot... Anyway, I was able to configure Airport Express, but I was told I could use it to expand my wireless network inside my house; which I found it´s not possible.
So, I´m returning my Airport Express to the store tomorrow and try to figure out a way to extend my wireless in any other way.
Any sugestion? Big houses are a problem...
Best regards, and once again thank you!
Antonio

Can't configure airport express with laptop after 10.5.6 update

I can't configure airport express with laptop after 10.5.6 update
the airport express is seen but can't access configuration screen, I get the spinning wheel forever.
Other computer gets to the configuration screen without problem.
And the airport utility describes the airport express like this: syAP.802.11format

I downloaded the airport utility and re-installed
and the problem was solved

Cant load the airport express with 802.11n

today i just got my new airport express with draft n. but my router can't load the config anymore after i uploading my setting ( change to N with 5 GB ). i've tried all of methods that the manual included. I think i need to exchange the new one. i just bought it yesterday.
i wanna know that would apple store give me refurbished product to me ????

today i got a replacement of AE with 802.11n. the same problem come up. Cant load the configuration. how on earth can i change the setting of my AE? this is my second times, my serial number is 6F8111XXXXX. Please apple fix it.
***

Airport Express with Time machine vs. Time Capsule?

I'm looking at replacing my backup system. I like the idea of Time Capsule with Time Machine, but I'd like to know if Airport Express with an External drive really works as reported with the March '08 firmware update. I can't find a single place where Apple confirms this.
Also, I look at time capsule and think it's cool, but with $179 (AEBS) + ~$200 (USB 1TB drive) = $379
and 1TB TC running $499, why would I buy TC? The AEBS system gives me the ability to easily swap the drive if it fails and I could buy a drive with a 3-5 year warranty vs. the 1 year on a Time Capsule?
Comments?

I assume that this is a new AirPort Express and you have not tried to configure it previously.
Locate the AirPort Express in the general area where you would like to have more wireless signal coverage.
Connect the Ethernet cable to the WAN "O" port on the back of the AirPort Express
Power up the AirPort Express and let it run a few minutes. The amber light will be blinking slowly at this point.
Click the AirPort icon at the top of your Mac's screen and wait a few seconds for a listing of New AirPort Base Station to appear. Just below that, click directly on AirPort Express.
AirPort Setup will open up automatically on your Mac, take a minute to analyze the network, then announce that the AirPort Express will be configured to extend the Time Capsule network.
Enter a device name that you want to use for the AirPort Express and click Next
Wait a minute while AirPort Setup configures everything for you. When you see the indication of Setup Complete, click Done.
You should be all set.

Is it possible to extend the range of one airport express with a second airport express?

Hi,
We have a Time Warner router and have it hardwired to an Airport Express. Is it possible to extend the range of that one airport express with a second airport express?

... The new AirPort Express that I have is an 802.11n version, but the second one is an older model and I don't know which version it might be. Also, the system recently updated so I'm using the AirPort Utility 6.1.
If you are using Mountain Lion, AirPort Utility 6.1 is the version installed by default. It will not be able to administer "older" AirPort base stations.
For them, use AirPort Utility 5.6 which contains the features you need. It can administer your older Express as well as current production base stations.
AU 5.6 is compatible with Lion as well as Mountain Lion, however, the installer app will refuse to install it on Mountain Lion.
This dilemma is easily solved though. You simply need to extract the app from the installer package using a package extractor like Pacifist.
Download Pacifist here: http://www.charlessoft.com/
Download AirPort Utility 5.6 here: http://support.apple.com/kb/DL1482
If you happen to have an archived copy of the AU 5.6 app somewhere, such as a Time Machine backup or equivalent, you can simply restore it or drag the app to your Mountain Lion system's Utilities folder. It will run without complaint. It is only the package installer that is the problem.
Mountain Lion will not allow you to delete its existing version of AirPort Utility. Just ignore it. It and the older version (which will bear the unique name "AirPort Utility 5.6") can peacefully coexist.
Note: For those with Leopard or Snow Leopard systems you need AirPort Utility 5.6.1 (this is confusing - a later AirPort Utility version for an earlier OS X version - but it is correct).
Download AirPort Utility 5.6.1 here: http://support.apple.com/kb/DL1536

Trying to get my Viera TX-P42S30B hooked up to me home network via Airport express with no luck.

Trying to get my Viera TX-P42S30B hooked up to my home network via Airport express with no luck.
Have tried both wired (network cable) and wireless to no avail, can't find much info online, any help appreciated !
Airport utility 5.5.3
Airport Extreme 802.11n
Airport Express 802.11g

The problem is that the AirPort Express (AX) is creating a subnet.
To prevent that, configure the AX to act as a bridge (so that it is NOT sharing a single IP address).

AirPort Express with PC -- Setup Problems

Similar Messages

Maybe you are looking for