All my problems listed, need help...
I have got my MSI K8N NEO for a while now. This are my problems with it.
Memory: Corsair XMS3200PRO 2x512MB
When I first got my memory I couldn't reformat or reinstall Windows XP. I had the memory in slot 1 and 2.
I read a lot here and checked Corsair forums and there was a knows problem with XMS3200 on K8N NEO.
So to get it working you have to put the memory in slot 1 and 3 with a voltage of 2.7 (not allways but its recommended) and to be sure, use the timings 2.5 3 6 3 T2.
I got my Leadtek 6800Gt today and ofcourse, I wanna reinstall WindowsXP.
So I boot the CD but it freezed :(
So I remove 1 of the moemory modules (the one in slot 3) and try again.
I now got 1 memory module in slot 1 with 2.7v 2.5 3 6 3 T2 timings.
NOT WORKING as soon as I started format, my comp restarted.
Well I move the memory to slot 3, restart and boot from the CD
Now it worked, YES (I only have 512MB of memory but it's a start)
Windows is installed and I'm starting to update.
I got SP1 installed on WinXP and I ran a Windows update to get all fixes
I installed DirectX9c
Latest nForce drivers from Nvidias homepage
Latest GFX drivers from Nvidias homepage
Latest AMD64 drivers
So all set for a benchmark of my new gfx card in 3Dmark03
First test worked fine...
Next test, , it freezed for some sec
same @ third and in the end of the fourth test, the comp freezed...
NOOOO!
I saw a thread here, about freezings and missing textures, so I checked it out.
Okey lower some stuffs raise volt turn of fast writes...
Test 1: prefect
Test 2: prefect
same for test 3 but test 4...
FREEZED
Okey I changed some more things, tested other settings and with osme settings (dont remember now).
I got passed all tests and in the loading of PS 2.0 the comp freezed :(((
BTW sometimes then I run 3Dmark03 the ocmp freezes and sometimes the screen goes black and the comp beeps... beeep beep beep I think it is one long and 2 short after.
So what do I do? I must be the MSI K8N NEO that's the problem
I run @ stock, even lower....200MHzx10
The memory in slot 3 2.7v 2.5 3 6 3 T2
I got a aspire 520W psu and it's very nice so itäs not a psu issue
hope I got all the info in here, if it's any other info you need please tell me
ohh and before I got my GF6800 I had a GF TI4400 and same problems there
thx
Memtest86
Similar Messages
-
My iPhone4s turned itself off and will not turn back on unless it is charged at all times. I need help and answers please.
And we would need more info. "will not turn back on unless it is charged at all times." is pretty obvious: the phone will obviously not turn on unless it is charged.
Describe your problem clearly. -
My new iPhone 4s and my iPad 1 have the same problem: While working on one of them, the screen goes black and the right back to home screen. I've tried resetting the iPad with no chages to this problem. Need help, this is anoying.
I just did a reset all settings on both.
Will see where this gets me.
Thank you for your helpfull input. -
NOkia E63 All Software Problems listed, Ignored by...
here are NOkia E63 All Software Problems listed.
-- Picture Editor:
You can Zoom, Rotate a Picture but E63 never allows to Save the edited Picture, Worst SOftware Engeering.
-- No Calendar Sync with Address Book Events
Add a Birday/Annivesary event along to a contact, you will never see the event entered to Calendar/neither gets a remainder alarm on that occassion.
Very Sad to say Nokia has very less knowledged engineers who are not even capable of giving a software which Rs 500 mobile gives with colors.
-- Memory Card COrrupted and needs a restart of MObile to recongise the Mem Card
3 to 4 times a day and every time when you switch off and switch on You need to re-insert the memory card(which is supplied along with MObile by Nokia)
-- Picture Viewer
Awesome, you cannot open pics with folder wise,
Open a Pic from folder, delete the that pic, you will be routed back to Home screen instead of folder.
What a Testing Engineered SOftware.
and after encryting memopry card, and after decrypting i am not able to see pics on pic viewers.
but can access to files directly going to Mem card folders.
ENcrypt and decrypt are juts for name sake, not for functioning and serving the need.
-- Contacts
Enter one or two char in search, Say
Ma
it lists out
Mahesh
Manikanth
Martin
Mariya
though i see the contact Mariya, i cannot scroll down to select that Mariya Contact
i should have to enter full name.
then why we need Search option, lets go scrolling down from begining.
-- Message Inbox
Wow, Interesting Area,
1. Just Say i received a message from Number 123456789, now go and save 123456789 as Balaji in Contact.
Now get back to your Inbox, Surprise, you never see 123456789 updated with COntact Name Balaji, it will stay as 123456789 only, even give a try of Swithc off and Switch on 100 times, its same.
its new nokia software getting back to 1950s.
2. Now, one more test:
You have already saved a friend number 12345 as Balaji in contacts.
you get a SMS from 12345, well the inbox now promptly shows message from Balaji, now go back to Contacts, and change the number 12345 to any number,
so now Contact Balaji's number is changed but you will never see this reflected in inbox.
you will be still shown as message from Balaji, though that number is not at all saved.
One more roboustness testing:
You delete the contact Balaji, still you see in Inbox SMS from Balaji.
-- Wi-Fi.
Even with dedicated Wirelss internet connection, E63 just detects the connection but when started browsing, i just get5 this.
"No Gateway Reply !"
you give a try for 1000 times you wont get internet brrowsing in E63,
i get heavy headache if i start thinking why i paid RS12000/- for Junk.
if i meet any of NOkia people at my office i will kick to them for sure.
Nokia should be Sued.
if i keep on digging the non-sense behavior of Nokia E63 i dont know, instead i can write a pretty good software.
Dear Nokia,
I need all this and every software problems to be fixed, else i will go to COnsumer COurt,
this is cheating All indian Customers, Taking RS 12000/- and not even providing a sofwtare which a RS 1000/- gives.
And if i wont get all this erros fixed by 15days, i will publish all this info at all leading weblinks, and will ask none to go for Nokia,
because Nokia has forgotten what is SOftware.
Regards,
Balaji M
EVen after Several Mails to [email protected] i got mail as "All the mobile phones do not support all the features. Further, we endeavour to address any concern or suggestions that may be raised by our customers. We thank you for your valuable feedback and have forwarded the same to the relevant department for their due consideration."
i really dont understand why Nokia Customer Care perdonals are always so dump like Nokia SOftware Engineers, i am asking for existing features not working properly but they comment saying "All the mobile phones do not support all the features"
Again they say, if any questions ask at Nokia !!
I am listing out the problems that your very high end Mobile Costing Rs. 12000/- INR which is failing to give even Rs 1000/- worth mobile.
This is all the questions I have, again why should I have to go and ask the same at Ask Nokia" at www.nokia.co.in/asknokia ?
once listed problems are answered again and again just for formalities they are asking ask question.
I want the Board or Directors and Senior responsible personals to attend to this, and get me bug free mobile for what i have paid RS12000/- else return our money, else i will soon file a Cheating case of not providing a said fetaures working phone by Nokia at COnsumer COurt, India.
Iam not the one facing this, just visit mouthshut.com, you will see people crying with erros on NOkia even after paying RS 30,000/- who's money is all this ?
I am awaiting for the response with bug fix by 24 hours.
and also i need my money back by 1 week.
Balaji M
Moderator note: Contact information removed - it is unwise to publish such information on a public forum.
Message Edited by michaels on 14-Oct-2009 10:59 AMNokia E63 has a name sake encryption and decryption. Once you encrypt and decrypt it is difficult to find any of your old saved files. Paradox is that the memory status will show a huge quantity of used space. But GOD only knows where the files are. Nokia support centres have no answer for this problem. I lost a large chunk of my pics n files. Shame of Nokia.
-
on Windows 7, CS6 all products, but especially need help with ID. Fonts that are showing in other applications are not showing in ID.
The ID Program folder will be relevant to your OS...
I took a shot and right clicked on my Scripts Samples, choose reveal in Explorer and opened up the ID Program folder.
As shown, there is a Fonts folder.
Drag/Copy/Paste fonts to this folder. -
After updating my iPhone 5 to ios 6.1 I'm getting a hissing sound during calls. Any one else having this problem? Need help
I am having the same issue. I am updating to 6.1.3 to see if that helps. It is really annoying. It seems to vibrate as well as hiss on my ear piece speaker while on a call. I keep looking at the phone thinking maybe another call is coming in.
-
MSI K7N2G-ILSR Problem! Need help!
Hi,i bought a K7N2G-ILSR last year when i was in Germany. This mainboard never worked as well... I wanted to work with Athlon XP 2500+ and Dual Channel 256MB+256MB=512MB 400 Mhz DDR-Ram. It hasn't worked when i first wanted to use and i changed the jumper to the securit mode than it worked but it has never opened with one button pushing.I was always trying to get screen vision with 3-5 closing and opening.One day i tried to get the jumper back and i tried to open but it never worked. I got the jumper securit again but again never worked. I tried everything but it never worked after that event. Normally i had to inform it at first and give it back or give it to the repairing but i couldn't have time. Now i have to do it this time. Now i want to change this or something else but in Turkey. I am living in Turkey and does MSI Support Centre change it or repair it? What can i do to get rid of this problem. Need help!
Thanks for your helps from now!MSI K7N2G-ILSR Mainboard 11X166
AMD Athlon XP 2500+
2X256 MB PC 3200 Twinmos
OnBoard Graphic Card
Samsung 40 GB 5400rpm HDD
300 Watt Power Supply
I dont have more infos but i can find out if you want... -
Hi all,
I need help with creating a "ragged" 2D array. The situation is that the columns have a static length which I know in advance but the number of rows needs to be defined per coloum seperatly. i know that i can create a ragged 2D array by setting the rows and looping throuh the rows setting the length (i.e. number of columns) but I have the opposite values. is this possible??Number of rows per column? A 2d array is basically
one column with M rows and each row is N items wide.
So define one collection object, I'll use a List for
the sake of argument. This is that one column with M
rows. For each row, add a List as an element in this
column, and add N elements to this row List. There
you go, a variable column length and each row is of a
variable length as well.The issue i have is when defining the 2d array i.e. lets say of type int
int[][] array = new int[M][N]
I do not know M but do know the value of N. only after I have defined this section I can then continue to define M for each N .. any ideas? -
WRT54G Access Restriction Time /Day Problems. Need Help!
Hi,
I have a WRT54G wireless router. When I set the access restriction time to DENY everyday from 11:00pm to 6:00am, it displayed that "The end time must be bigger than start time!". It is from 11 at night to 6 in the morning. How else do I set it? I even upgrade the firmware to v4.21.1 but it still does not work with that time setting. I tried to set to ALLOW everyday from 6:00am to 11:30pm and it accepted the settting but it just applied the restriction right away without waiting for the right time (after I enable it, none of the laptops can access internet even its only 9:10pm).. The time in the linksys setup page is correct as well as all my pcs. Please help! Thanks.The Access Restrictions feature of a Linksys router allows you to limit Internet access on your network. You can deny certain computers’ Internet access or block certain applications and services.
Here is the link for setting up the Access Restrictions on a Linksys router: http://www6.nohold.net/Cisco2/ukp.aspx?vw=1&docid=20b29e54474a4a17aff594cb659747ea_4041.xml&pid=80&r... -
Problem - Define Forms for Check Deposit List - Need Help
Hello Experts,
I want to extend the logic of T Code FP20 (Prog RFKKCK01),
Hence, I have created a 'Z' prog with the appropriate extension in the logic.
Now to take these change effectively, i have made corrensponding changes in the attached SAP Script (FKK_CHECKDEPOS) also.
Now, when I go to
Contract Accounts Receivable and Payable -> Business Transactions -> Payments -> Processing Incoming and Outgoing Payments ->Define Forms for Check Deposit List.
In this, I create a new Entry after removing the existing Entry of the same Company Code [1000 | ZRFKKCK01 | SapScript | ZFKK_CHECKDEPOS ]
it gives me an Error "Specify the key within the work area".
Specify the key within the work area
Message no. SV033
Diagnosis
You have attempted to create an entry whose key is not in the range defined for this area.
System Response
The entry cannot be created.
Procedure
Please check your entry.
Please Help me solving this problem.
Thanks!!Thanks sbaranga. This code won't work for me.
<select>
<option value="P"if (statusIndicator.equals("Pending")){ selected}>
<option value="A"if (statusIndicator.equals("Approved")){ selected}>
</select>
In above code statusIndicator is ID I believe. I need to show selected item based on statusIndicator in database. Also it has to pass updated status to database incase if user changes status thru form.
If they select Pending then "P" will be passed to servlet and if they select Approved then it will pass "A" to servlet.
I will be receiving "A" or "P" from database when I am trying to retrive status value from database. Based on value "A" or "P" I need to change selected information on form.
Update and Retive form are same. this one form does everything display and update.
I hope this help to understand my question.
If you have any question then email me at [email protected]
Thank you. -
WRT54G Wireless Router Problem. Need Help!
I'll start with the basics of my situation and if more details are needed, I will provide to the best of my ability.
I have a comcast cable internet connection. I have 6 computers in my house. Two of them are downstairs (which is where our modem is.) The other four computers are upstairs. All of these computers are Desktop computers with the exception of one laptop.
My laptop (which is Windows XP) can pick up a random wireless signal from the room it is in. I also found out a way to share the internet connection on the computer by going into the properties of my network connection and enabling internet sharing on it. This means if I connect a network cable from my laptop to another computer, I can leech the connection from my laptop and have internet access on the other computer. I also had a switch that I used to connect the other 3 computers upstairs by means of the laptop. The problem was, the laptop was using someone else's wireless connection in the area, and it wasn't strong enough to keep up a constant connection.
I decided, if I can leech someone else's wireless connection, why not have my own. So i recently bought WRT54G Wireless Router and set it up on one of the computers downstairs (because that's where the modem is). It works fine as far as connecting my laptop to the internet from upstairs. My laptop can access the internet through the connection I set up in the LELA program.
Here is the part I am confused about. Everything is plugged in correctly as far as the router is concerned because the laptop can access the internet. But when I connect an ethernet cable directly to one of my other computers (which are Windows Vista, but I didn' t have a problem with it previously when I was leeching someone else's connection), the connection drops on my laptop, and the other computer still can't access the internet. A notice pops up that says its trying to identify the network, but it gives an error that says there is something wrong with the DNS. As soon as I disconnect the ethernet cable connecting my laptop to one of the other computers, the connection is fine again on the laptop. It's only when I connect the computers together that the connection drops.
I just don't understand why it wouldn't work when I created my own network if it worked with another network with no problem. My whole point in getting a wireless router was to have a router within good range to keep up a constant connection on my other computers that aren't in range of the modem downstairs. I just don't know where else to look. I'm not sure if it can be fixed on LELA, manually through my wireless settings, or if it could be a problem with one of my computers' settings. I've tried many different things and I'm not sure what else to do so any help is most definately appreciated. I feel like I've tried everything. I know it's possible because I've one it before, I just need the help because I'm not much of a networking person and I don't know what I should start with to make this work.
Thank you to anyone who can help or even point me in the right direction.Access router setup page ...Click on the Wireless tab on the Setup page- Here Wireless Network mode should be mixed- Provide any non-linksys name .... Set wireless channel to 11- And wireless SSID broadcast should be Enabled and then click on "Save Settings" >>Now Click on the Sub tab under wireless > "Wireless Security" Change the Wireless security mode to WEP/WPA ...type in the key & click save settings .... >>>>Click on Advanced Wireless settings>>Change the Beacon Interval to 75 >>Change the Fragmentation Threshold to 2304 Change the RTS Threshold to 2304 >>Click on "Save Settings" Check the connection once again & see if it works or not ...
-
T500 overheating problems - Novice needs help
Like for some others in this forum, my Thinkpad T500 is overheating.
Here are my specs:
Model: T500 (Type: 2055)
Processor: P8600 (2.40GHz)
GPU: ATI Mobility Radeon HD 3650
When I'm doing most regular activities (browsing,emailing, documents), laptop is fine. The unit gets warm underneath, but I've not had problems.
If I'm doing more intensive activities (watching local video,Netflix, or Skyping), laptop starts to heat up enough so that it's uncomfortable on my lap.
When I play games (Nothing crazy intensive: e.g. Minecraft, Civilization 4), and sometimes when I Skype, the unit gets extremely hot underneath and shuts off without warning.
The heat seems to be originating from the left-hand side of the laptop, near the back. Unless I'm mistaken, this is where the GPU is located. And this makes sense, since the overheating seems to be related to graphics-intensive activities.
So, my questions are:
1. How can I diagnose this problem further? What's a good utility to use to monitor heat of GPU and CPU? Anything else I can use ?
2. Are there any settings I can change on my laptop to prevent the automatic shut-downs and excessive heat?
3. I've seen some mention of people cleaning fans, replacing fans / cooling units, or adding thermal paste. Need some advice there too.
Any suggestions are welcome.
Thank you!Good day and welcome to the community.
If you've never had the machine open to blow out dust from around the fan/heatsink assembly, I'd recommend that first. If you download a copy of your Hardware Manual: http://download.lenovo.com/ibmdl/pub/pc/pccbbs/mobiles_pdf/43y6630_04.pdf , you'll see that by pulling the palmrest, keyboard and keyboard bezel (manual pages 88-90, 92-93 and 102-103, respectively), that you'll expose the top side of the assembly in the upper left. The top view image on page 107 is helpful. The CPU is beneath the end section of the wider heatpipe and the GPU is beneath the narrower.
While holding the blades of the fan stationary (important!), you can use canned air to blow all of the dust from the inside out through the exhaust vents. Once done, button everything up and see if things run cooler. If you're still overheating, you may need to clean off the old thermal compound and apply new, but try the de-dusting first.
Regarding temp monitoring, many folks like TPFanControl: http://www.staff.uni-marburg.de/~schmitzr/donate.html
Scroll about 2/3 down the page for the download link for v0.62 which is the latest. It can be run in monitor-only mode or can be configured to provide a level of control over your fan speed.
Please post back your results from the first step and we can go from there.
Regards.
English Community Deutsche Community Comunidad en Español Русскоязычное Сообщество
Community Resources: Participation Rules • Images in posts • Search (Advanced) • Private Messaging
PM requests for individual support are not answered. If a post solves your issue, please mark it so.
X1C3 Helix X220 X301 X200T T61p T60p Y3P • T520 T420 T510 T400 R400 T61 Y2P Y13
I am not a Lenovo employee. -
Ipod photo - serious music transfer probleme. i need help please
hi there.
i have a problem that i cant resolve.
i search and ask on french forum, but nobody could help me.
actually, my ipod didnt want me to upload files over 6 minutes.
an error message box used to pop up on itunes each time the delay of about 6 minutes music transfering exceed.
here is the msg box:
http://fr.audiofanzine.com/img/membres/normal/6/9/69236.png
he told me that itunes couldnt read/write onm my ipod.
that's false cause he could upload <6 minutes music transfering time.
anyway i reeset my ipod, update it with ipod updater.
and the problem is still the same.
i still get this message.
i tried with many kind of music, coming from diferent HD, but nothing to do.
i tried to find a help from apple, but this stupid website is made for you not to find a way to contact them.
if someone can help me, i would be glad...
my ears need sounds...If you have already done so, have a look at this Knowledge Base article: "-36 or "Disk cannot be read from or written to" when syncing iPod or "Firmware update failure" error when updating or restoring iPod
If you have no success there I would try restoring your iPod, this will erase the hard drive, reload the software and put it back to default settings so make sure you have all your songs backed up in iTunes. A fresh installation of the software should sort things out: Restoring iPod to Factory Settings -
Upload/Put problem - basic, need help
Aloha,
my first post here.
I used to use Dreamweaver 8 and recently upgraded to CS3.
For some reason now when I upload an HTML page that contains
j pegs, or swf files only the HTML page gets put, I have to
manually go and put each j peg or swf file. It used to
automatically put all the content of the page, why is it not doing
it anymore? Is there a setting I need to change in preferences?
Any help is appreciated.
thanks
e~You can 'put' or 'check-in' files either independently or
Shift+click (PC) linear groups or Ctrl+click (PC) randomly spaced
files. If you have files within folders you can put/check-in an
entire file and its contents.
You can also automate the uploading of dependent files (which
is probably what you had selected in Dreamweaver 8).
Select Edit > Preferences (Windows) or Dreamweaver >
Preferences (Macintosh).
In the Preferences dialog box, select Site from the category
list on the left.
Set the options ( you want dependent files) and click OK.
This will upload the html page and every file referenced in
the page such as images, external scripting and css files and swfs.
This can be an unnecessary step once you have completed the first
upload of an html page and its contents. You might consider simply
holding down the Alt (Windows) or Option (Macintosh) when selecting
put/check-in if you need to upload every associated file. I prefer
to leave the dependent file option deselected and use this method.
Regards
Nick Barling
www.barkingweb.com -
N900 PC SUITE / OVI SUITE Problems. Need help.
HI,
I am having big issues with conecting my N900 to my PC. Had a long list of troubles uninstalled everything after expeirencing Driver issues on to get Phone parent issues after re install. went through it all again and downloaded latest version of PC Suite 7 from nokia site and it's been installing for 2 hours now and is stuck at 32%.
Really frustrating just upgraded from E75 which worked perfectly with OVI Suite. now i have N900 that i can't back up or update. Non of the solutions i've read on the board have helped, i'm now into day five of uninstalling - re installing and downloading. Doeas anyone have a solid fix for this soon to be thrown out the window N900 ?
Many Thanks.Surprise surprise USB Phone Parent (no file located) !!! So disapointed, Somebody at Nokia must be able to offer a Solution. Without PC connectivity the N900 is just a very expesive Brick.
Firstly i live in the poorest contry in Africa so when i paid over 1000 USD for the phone i was annoyed that it had a chrging problem as many people have had i notice from the boards. I go to Europe and take it to a Nokia shop, I am told "no we can't fix it it must be done in the country you bought it". Well thats kinda impossible as Nokia have no facilities in Mozambique, so another 800 USD trip to South Africa to get it repaired.
Secondly Absolutely no assistance from nokia with the PC connectivity issue for either OVI or PC Suite.
I knew the iPhone was the smart choice ! anybody wanna buy a 1000USD Brick OR Help me resolve the PC connectivity issue?
Attachments:
SS08242011135720.jpg 97 KB
Maybe you are looking for
-
hello sir,i need labview code for a code which is written in matlab... clc; close all; clear all; Ez= zeros(1,200); Hy=zeros(1,200); Ca=1; Cb=.4519; n=1; while(n<1500) for k = 2:200 Ez(k)=Ez(k) + Cb*(Hy(k)-Hy(k-1)); end Ez(1)=1; for k=1:199 Hy(k)=Hy(
-
First Very Simple Socket Program
Hello, I am learning about Sockets and ServerSockets and how I can use the. I am trying to make the simplest server/client program possible just for my understanding before I go deper into it. I have written two programs. theserver.java and theclient
-
How to copy a node from one dom document to another?
I have one dom document that I have to split up into multiple dom documents. I am able to get the inividual nodes that I want to put into seperate documents. My problem occurs when I create a new dom document and try to add the node from the parent d
-
How can I change the location of the message filestore?
The MQ default message store is located at /var/imq/instances/brokerName/filestore/ on Solaris. Is there a way that we can change this location? Thanks.
-
TCP connectivity of subnet error : pre installation check oracle 11.2 RAC
Hi, I am trying to setup RAC 11.2 on Centos 5.7. When I run the preinstallation check, I am getting this error: Check: Node connectivity of subnet "192.168.210.0" Source Destination Connected? rac2[192.168.210.102] rac1[192.168.210.101] yes Result: N