Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones?

Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones? They don't seem to be (a 7902G won't power on when connected to an SF302-08MP with firmware version 1.1). Is any special configuration needed on the switch to enable this detection?

Please note that the 200 and 300 Series switches now support Cisco Legacy POE as of September 2011, allowing it to deliver power to 7960, 7940, and other pre-standard phones and APs. Details provided at the following link:
https://supportforums.cisco.com/docs/DOC-18337

Similar Messages

  • Cisco 300 series switches with 802.3at standard

    I'm a bit confused as to which of the 300 series switches supports the 802.3at standard. According to the website, the SG300-28P supports it. But in the quick start guide for the 300 series, only the MP models (excluding the SF302-08MP and SG300-10MP) including the SG300-52P has it. Can someone give me a difinitive answer to this? Thanks!

    LJ,
    P    = PoE capable. On the 300 series, half of the ports can provide 15.4W, or all can provide half that.
    PoE+ is NOT SUPPORTED.
    MP = Maximum Power. This means that all ports can provide up to 15.4W. PoE+ is supported on some models only.
    PP = PoE Plus. Can provide up to 30W on a single port. Note the maximum PoE budget for each switch. Also,
    half of the ports can provide 15.4W, or all can provide half that - any extra power used by PoE+
    MPP = Maximum Power and PoE Plus. This means that all ports can provide up to 15.4W - any extra power used by PoE+
    According to the Data Sheet:
    "Switches support 802.3at PoE+, 802.3af, and Cisco pre-standard (legacy) PoE. Maximum power of 30.0W to any 10/100 or Gigabit Ethernet port for PoE+ supported devices and 15.4W for PoE supported devices, until the PoE budget for the switch is reached"
    The PoE+ models are brand new and are not widey available yet. I did a web search for SG300-28PP and found that at least a few online resellers have it in stock.
    - Marty
    Message was edited by: Martin Pyhala

  • Using TACACS+ With ACS 5.6 on 300 Series Switches v1.4

    I was wondering if anyone could give me instructions on how to set up ACS for TACACS+ on a 300 series switch using Authorization? I can get it to work to authenticate, but the authorization doesn't seem to work like a catalyst switch. Thanks in advance for any help!

    Brandon, thanks for the link, but this is for the older software before they included authorization (the v1.4). I've looked through a bunch of manuals and tried to find examples online, but it doesn't seem like anyone has anything out there I can find.

  • CCA for 100 + 300 series switches?

    Is it in the roadmap to provide CCA control over 300 series switches?  We have a lot of SRW2008's put in before the 8-port ESW existed...and we have PITA vlan consistency issues out there too that I think CCA would help fix. 
    While I understand the "don't pre-announce products", I need a level of design intent around CCA - is it a tool for configuring UC series pieces primarily and all else is secondary? Or is it the multi-device config tool for all SBCS pieces?

    Nothing to do with the UC - primary concern is standalone networks.
    Real life case:
    2 ESW switches in control room hooked up to SA540
    Closet switches are SRW2008's
    Port no more than two devices are supposed to go now has 4, add an SRW2008 to the desk location.
    Now, it turns out that there is a badly behaved device at the desk - a video player that spews all sorts of traffic when it's playing that doesn't play nice with others.  So I now need to set-up a VLAN crossing those two switches. Oh, and it turns out the customer decided to unplug an access point and plug it into that switch too which ended up causing a loop when the PC plugged into ethernet someplace else attached to the PC.
    Tasks:
    Ensure that the 2 SRW2008's have proper vlan assignments to setup a port vlan for that video server.
    Issues:
    Make sure you assign proper configs to both ends of each link
    Make sure not to confuse one SRW2008 with another
    If new vlan, make sure all other ports that need to see it can still see it.
    Applications for CCA:
    Visualize all VLANS
    Document port assignments (i.e. where is the video server vs. printer on that last leg 2008)
    More easily see port statistics across multiple switches
    So after I did that work, I realized that the SA540 wasn't really up to being an aggregation switch too and made the ESW-540-48 into the aggregation switch which required some more changes - however CCA made it easy...
    At another job, I have SA540 + AP541ns (upgraded from RVL200 + WAP54GP's) but if I had 300 series in CCA, I'd upgrade the SRW2024's and SRW2008's but without easy management tools, the labor cost will be too high to make their networks really managed.....CCA makes that layer of management cheaper.

  • Firmware upgrade question for 300 series switches

    Hi-
    I have a customer that is investigating a strategy and solution for centralized firmware management of the 300 series switches.  They have found an issue in the lab where they were trying to roll back the firmware to a previous version  They can not roll back to the previous firmware version, which is desirable in the case of finding an issue in the new firmware that causes them to have need to rollback to a known working version.
    We have read in the cisco 300 switch admin guide that there are two images (active and inactive) and that a new downloaded firmware always replaces the inactive image and is active until explicitly set.  The admin guide does not mention inability to make an older firmware image as active image when the switch has previously run on a new release firmware image.  My customer's engineers testing have informed me that an older image can not be made active after a newer image has booted.  Can you please verify if this if a fallback is supposed to work as it is causing a lot of concern-
    Thanks-
    Jena

    Jena,
    The release notes -
    http://www.cisco.com/en/US/docs/switches/lan/csbms/sf30x_sg30x/release_notes/Sx200-Sx300_R1.1.2.x.pdf
    What firmware is the switches currently on?
    Major Changes and Defects Corrected
    • Hardware version 1.0 devices that were upgraded to software version 1.1
    can now be downgraded to software version 1.0. You must delete the
    startup configuration file before rebooting the device to software version
    1.0. Otherwise the device may have problems when booting up. You may
    backup your running configuration before the reboot, and re-import the
    configuration afterward. Major Changes and Defects Corrected
    • Hardware version 1.0 devices that were upgraded to software version 1.1
    can now be downgraded to software version 1.0. You must delete the
    startup configuration file before rebooting the device to software version
    1.0. Otherwise the device may have problems when booting up. You may
    backup your running configuration before the reboot, and re-import the
    configuration afterward.
    Please read full release notes for other work arounds
    Hope this helps,
    Jasbryan

  • Are Type 1 Fonts compatible with Windows 8 Pro 64-bit?

    Are Type 1 Fonts compatible with Windows 8 Pro 64-bit?
    Can anyone point to a specific reference that says Type 1 fonts should or shouldn't work?

    Hello Nikhil.
    Can you see here?
    MAIN MODULE INFORMATION:
       SAP GUI for Windows
       SAP Logon Pad for Windows
       730 Final Release
       7300.1.0.1074
       1337608
    SYSTEM INFORMATION:
       Operating system: Windows 8 Pro 6.2 (9200)
    You are using patch 0 for Windows 8
    Windows 8 is not supported until patch 1 or higher is applied, and for Windows 8.1, you must use
    Patch 7 or higher,.
    Apart from that the error is not from the GUI side,
    See below:
    Previous frontend interpretation time   :           109 ms
    Previous server response time           :          5078 ms (for 1 roundtrips)
    The frontend interpretation time is only 100 ms whereas the server time has taken 5000 ms
    Please use a supported version for the OS you intend to use.
    You can find this information in note
    http://service.sap.com/sap/support/notes/66971
    Jude

  • Are Nintendo DS headphones compatible with an iPad's headphone jack?

    Are Nintendo DS headphones compatible with an iPad's headphone jack? iPad 3rd gen. Wi-Fi iOS 5.1.1

    Headphones will fit fine. Now if you want to use a headset (speaker+microphone) that's another matter. DS headsets, which have a seperate prong for mic input, are not compatible with the iPad.

  • TACACS+ Authorization on 300 Series Switches

    I was wondering if anyone could give me instructions on how to set up ACS for TACACS+ on a 300 series switch using Authorization? I can get it to work to authenticate, but the authorization doesn't seem to work like a catalyst switch. Thanks in advance for any help!

    Brandon, thanks for the link, but this is for the older software before they included authorization (the v1.4). I've looked through a bunch of manuals and tried to find examples online, but it doesn't seem like anyone has anything out there I can find.

  • Poe881 Router and Cisco Inline Power (pre-standard PoE)

    I have a number of 881 Routers and 79x0 IP Phones. These phones use "Cisco Inline Power", aka "pre-standard PoE". In other words, they are not compatible with standard 802.3af PoE.
    It would be possible for me to install a daughtercard and DC adapter in the 881 routers and provide PoE to two of the ethernet ports. My question is whether the 881 (when equipped for PoE) will support Cisco Inline Power, or if it will only support 802.3af.
    For reference, the 200 and 300 series Small Business switches support these phones with a software upgrade. See this link: https://supportforums.cisco.com/document/71841/200-and-300-switches-now-supports-cisco-pre-standard-poe-legacy-poe
    Many thanks,
    Tom

    My question is whether the 881 (when equipped for PoE) will support Cisco Inline Power, or if it will only support 802.3af.
    Hi Tom,
    I don't have an 880 but I have a large fleet of 890 and all of them have PoE and I know these 890 support 802.3af easily.

  • How many pre-standard POE schemes by Cisco?

    I came across the 3Com NJ220 switch-in-a-wall-jack that claimed it could be powered by "some Cisco proprietary Power over Ethernet schemes". Does anyone know what these schemes are? Are all the older Aironet products (say AIR-PWRINJ2 and AIR-PWRINJ3) using the same pre-standard POE scheme?

    Technically, they have cards that put out different levels of power. The following URL lists some of the different blades and switches and how much power they put out.
    The reason for the difference is that once 802.11af was in the final stages, Cisco increased output to 15W as required by af on some switches such as 3550s, but it is still technically "pre-standard" since it did not meet all the specs exactly.
    http://www.cisco.com/en/US/products/hw/wireless/ps430/prod_technical_reference09186a008039e541.html
    -Eric

  • I have a new ipad which needs itunes 10.7 or later to download my music onto it... but my ipad is not compatible with this as it is too old... can i use itunes with this ipad and apple laptop?

    I have a new ipad which needs itunes 10.7 or later to download my music onto it... but my apple laptop is not compatible with this as it is too old... can i use itunes with this ipad and apple laptop?

    To use itunes 10.7 you need to have Snow Leopard operating system installed
    These are the system requirements
    System Requirements:
    Mac computer with an Intel processor
    1GB of memory
    5GB of available disk space
    DVD drive for installation
    Some features require a compatible internet service provider: fees may apply.
    If you can run Snow Leopard you need to purchase it
    http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard

  • My iPhone 4S not compatible with 2008 Q7 Audi MMI.  Now only phone numbers come up on screen, no name.  Names appeared on the phone screen but not MMI screen. Cannot dial by contact info while driving anymore.  Never had this problem with previous iPhones

    My iPhone 4S not compatible with 2008 Q7 Audi MMI.  Now only phone numbers come up on screen, no name.  When someone calls, only the number appears on the MMI screen, not their name or whether they called from their office/home etc..   Same with missed calls, dialed numbers etc.. Names appeared on the screen of the phone,  but not on MMI screen. Cannot dial by searching  contact and name info while driving anymore.  Never had this problem with previous iPhones.  Is this an Apple issue or Audi issue?  Anyone with this problem? Help!

    NIGHTMARE Finally Ends, after nearly two weeks.
    After trying for over a week trying to get my replacement iPhone 4S to activate, I ended up driving 110+ miles to an Apple Store to get a second replacement, which had been specially shipped there for me.  Popped in the SIM card, went through the setup and I finally have an iPhone 4S that works, at least for the time being.
    Advice to others who find themselves in this situation:
         1)     If you get these messages (see original post), the phone is bad.  Demand a replacement.
         2)     If the AppleCare tech advises that the Apple Agreement Administration team is investigating, you'll be waiting for a week or more for them to complete it.  Demand a replacement immediately, don't let them put you off indefinitely.
    After the initial phone call documented in my original post, I was in daily contact, phone & e-mail, with the AppleCare tech trying to figure out the problem, and we tried everything, from forced restore's to switching SIM cards, conferencing w/ AT&T, etc.  It seems that this was a case of first impression to Apple, but if it wasn't, then the problem is not well documented or known by those who should know, and for that, the blame should be on Apple, not the AppleCare tech who worked tirelessly trying to figure out a solution--I'd send him a case of beer if I knew where to send it.

  • Where is the 300 series switch with 48 gigabit ports and PoE?

    Love the 300 series but surprised that Cisco did not put out a 48 port model with gigabit and PoE.  Would love to hear from Cisco on the reasoning behind that and if there are any plans to introduce one?  Given that gigabit and VoIP is the future at many companies it only makes sense.

    The switches use the SFPs to link to each other. The SG500 has ports for 1G or 5G and the SG500X has 10G ports. Whichever port you select will be the speed at which the switches pass traffic and stack control information. These same ports can be 'reclaimed' if you were to set the switch to stand alone mode. I have put a chart below which details the ports you can use and the speed of these ports.
    Header 1
    Header 2
    Header 3
    Header 4
    Header 5
    Units in Stack
    SG500X
    SG500X
    SG500
    SG500
    Stack Port Name
    S1,S2-XG
    S1,S2-5G
    S1,S2
    S3,S4
    Stack Port Speeds
    10G/1G
    1G/5G
    1G
    1G/5G

  • Cisco 300 series switches

    hi all
    Ive looked through some of the online content but dont see a definitive answer to my question about the physical size of the switches, are they all 19" rack mountable or desktop?
    I look forward to a confirmation..

    LJ,
    P    = PoE capable. On the 300 series, half of the ports can provide 15.4W, or all can provide half that.
    PoE+ is NOT SUPPORTED.
    MP = Maximum Power. This means that all ports can provide up to 15.4W. PoE+ is supported on some models only.
    PP = PoE Plus. Can provide up to 30W on a single port. Note the maximum PoE budget for each switch. Also,
    half of the ports can provide 15.4W, or all can provide half that - any extra power used by PoE+
    MPP = Maximum Power and PoE Plus. This means that all ports can provide up to 15.4W - any extra power used by PoE+
    According to the Data Sheet:
    "Switches support 802.3at PoE+, 802.3af, and Cisco pre-standard (legacy) PoE. Maximum power of 30.0W to any 10/100 or Gigabit Ethernet port for PoE+ supported devices and 15.4W for PoE supported devices, until the PoE budget for the switch is reached"
    The PoE+ models are brand new and are not widey available yet. I did a web search for SG300-28PP and found that at least a few online resellers have it in stock.
    - Marty
    Message was edited by: Martin Pyhala

  • SG-300 28P switches problem with VLAN Data and Voice, working all the time as Voice VLAN

    Hi Everyone,
    Thank you very much for your help in advance. I’m pulling my hair to fix the problem.
    I  just got the new SG-300 28P switches. My Bios ordered for me. I did not  know how it runs until now... not an IOS based. I really do not know  how to configure it.
    I have 2 VLAN are Data and Voice.
    -          Data VLAN ID is 2 IP 192.168.2.X/255.255.255.0
    -          Voice VLAN ID is 200 IP 192.168.22.X/255.255.255.0
    -          I created two vlans, in switch, Data and Voice.
    -          On the port number 28, it is trunk by default, so I add Data vlan ID 2 tagged.
    -          On the port number 26, it is trunk by default, so I add Voice vlan ID 200 tagged.
    -          On the port number 27, I add Data vlan ID 2 tagged for Data vlan out.
    -          Port settings No.1
    I set it up as Trunk with Data vlan 2 untagged, and  200  Tagged (voice vlan). I plugged in a phone with a pc attached. But the  PC will get to the vlan 200 to get the DHCP address, but no from vlan 2.  The Phone works with correct vlan ip.
    -          Port settings No.2
    Trunk with vlan 1UP, 2T, and 200T. The phone is even worse. Would never pick up any IP from DHCP.
    -          Port settings No.3
    Access  with 200U...of course the phone will work... and the PC could not get  to its own vlan. Instead, the PC got an ip from the voice vlan. Not from  VLAN 2.
    I have Linksys phone I’m not sure if this help.
    For more information I setup in switch,
                - enable voice vlan
    - set the port on auto voice vlan
    - enable LLDP-MED globally
    - create a network policy to assign VLAN 200
    - assign this network policy to the port the phone is connected to.
    I  hope this information help to help me to setup Data and Voice vlans, to  plug the phone to work with vlan Voice 200 (IP rang 192.168.22.X), from  phone to Pc and pc work as Data vlan 2 (IP rang 192.168.2.X).

    I just got done setting up voice VLANs on an SF 300-24P and verified working.  This was working with Cisco 7900 series phones connected to a Cisco UC setup.
    Here's my sample config.
    Note that I edited this by hand before posting, so doing a flat out tftp restore probably won't work.  However, this should give you a clue.  Also, don't take this as 100% accurate or correct.  I've only been working with these things for about a week, though I've worked with the older Linksys SRW switches for a couple of years.  I'm a CCNP/CCDP.
    VLAN 199 is my management VLAN and is the native VLAN on 802.1q trunks.
    VLAN 149 is the data/computer VLAN here.
    VLAN 111 is the voice/phone VLAN here.
    VLAN 107 does nothing.
    interface range ethernet e(1-24)
    port storm-control broadcast enable
    exit
    interface ethernet e1
    port storm-control include-multicast
    exit
    interface ethernet e2
    port storm-control include-multicast
    exit
    interface ethernet e3
    port storm-control include-multicast
    exit
    interface ethernet e4
    port storm-control include-multicast
    exit
    interface ethernet e5
    port storm-control include-multicast
    exit
    interface ethernet e6
    port storm-control include-multicast
    exit
    interface ethernet e7
    port storm-control include-multicast
    exit
    interface ethernet e8
    port storm-control include-multicast
    exit
    interface ethernet e9
    port storm-control include-multicast
    exit
    interface ethernet e10
    port storm-control include-multicast
    exit
    interface ethernet e11
    port storm-control include-multicast
    exit
    interface ethernet e12
    port storm-control include-multicast
    exit
    interface ethernet e13
    port storm-control include-multicast
    exit
    interface ethernet e14
    port storm-control include-multicast
    exit
    interface ethernet e15
    port storm-control include-multicast
    exit
    interface ethernet e16
    port storm-control include-multicast
    exit
    interface ethernet e17
    port storm-control include-multicast
    exit
    interface ethernet e18
    port storm-control include-multicast
    exit
    interface ethernet e19
    port storm-control include-multicast
    exit
    interface ethernet e20
    port storm-control include-multicast
    exit
    interface ethernet e21
    port storm-control include-multicast
    exit
    interface ethernet e22
    port storm-control include-multicast
    exit
    interface ethernet e23
    port storm-control include-multicast
    exit
    interface ethernet e24
    port storm-control include-multicast
    exit
    interface range ethernet g(1-4)
    description "Uplink trunk"
    exit
    interface range ethernet g(1-4)
    switchport default-vlan tagged
    exit
    interface range ethernet e(21-24)
    switchport mode access
    exit
    vlan database
    vlan 107,111,149,199
    exit
    interface range ethernet g(1-4)
    switchport trunk allowed vlan add 107
    exit
    interface range ethernet e(21-24)
    switchport access vlan 111
    exit
    interface range ethernet g(1-4)
    switchport trunk allowed vlan add 111
    exit
    interface range ethernet e(1-20)
    switchport trunk native vlan 149
    exit
    interface range ethernet g(1-4)
    switchport trunk allowed vlan add 149
    exit
    interface range ethernet g(1-4)
    switchport trunk native vlan 199
    exit
    voice vlan aging-timeout 5
    voice vlan oui-table add 0001e3 Siemens_AG_phone________
    voice vlan oui-table add 00036b Cisco_phone_____________
    voice vlan oui-table add 00096e Avaya___________________
    voice vlan oui-table add 000fe2 H3C_Aolynk______________
    voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
    voice vlan oui-table add 00d01e Pingtel_phone___________
    voice vlan oui-table add 00e075 Polycom/Veritel_phone___
    voice vlan oui-table add 00e0bb 3Com_phone______________
    voice vlan oui-table add 108ccf MyCiscoIPPhones1
    voice vlan oui-table add 40f4ec MyCiscoIPPhones2
    voice vlan oui-table add 8cb64f MyCiscoIPPhones3
    voice vlan id 111
    voice vlan cos 6 remark
    interface ethernet e1
    voice vlan enable
    exit
    interface ethernet e1
    voice vlan cos mode all
    exit
    interface ethernet e2
    voice vlan enable
    exit
    interface ethernet e2
    voice vlan cos mode all
    exit
    interface ethernet e3
    voice vlan enable
    exit
    interface ethernet e3
    voice vlan cos mode all
    exit
    interface ethernet e4
    voice vlan enable
    exit
    interface ethernet e4
    voice vlan cos mode all
    exit
    interface ethernet e5
    voice vlan enable
    exit
    interface ethernet e5
    voice vlan cos mode all
    exit
    interface ethernet e6
    voice vlan enable
    exit
    interface ethernet e6
    voice vlan cos mode all
    exit
    interface ethernet e7
    voice vlan enable
    exit
    interface ethernet e7
    voice vlan cos mode all
    exit
    interface ethernet e8
    voice vlan enable
    exit
    interface ethernet e8
    voice vlan cos mode all
    exit
    interface ethernet e9
    voice vlan enable
    exit
    interface ethernet e9
    voice vlan cos mode all
    exit
    interface ethernet e10
    voice vlan enable
    exit
    interface ethernet e10
    voice vlan cos mode all
    exit
    interface ethernet e11
    voice vlan enable
    exit
    interface ethernet e11
    voice vlan cos mode all
    exit
    interface ethernet e12
    voice vlan enable
    exit
    interface ethernet e12
    voice vlan cos mode all
    exit
    interface ethernet e13
    voice vlan enable
    exit
    interface ethernet e13
    voice vlan cos mode all
    exit
    interface ethernet e14
    voice vlan enable
    exit
    interface ethernet e14
    voice vlan cos mode all
    exit
    interface ethernet e15
    voice vlan enable
    exit
    interface ethernet e15
    voice vlan cos mode all
    exit
    interface ethernet e16
    voice vlan enable
    exit
    interface ethernet e16
    voice vlan cos mode all
    exit
    interface ethernet e17
    voice vlan enable
    exit
    interface ethernet e17
    voice vlan cos mode all
    exit
    interface ethernet e18
    voice vlan enable
    exit
    interface ethernet e18
    voice vlan cos mode all
    exit
    interface ethernet e19
    voice vlan enable
    exit
    interface ethernet e19
    voice vlan cos mode all
    exit
    interface ethernet e20
    voice vlan enable
    exit
    interface ethernet e20
    voice vlan cos mode all
    exit
    interface ethernet e1
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e2
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e3
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e4
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e5
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e6
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e7
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e8
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e9
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e10
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e11
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e12
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e13
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e14
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e15
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e16
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e17
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e18
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e19
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e20
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e21
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e22
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e23
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e24
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet g1
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet g2
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet g3
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet g4
    lldp optional-tlv port-desc sys-name sys-desc sys-cap 802.3-mac-phy 802.3-lag 802.3-max-frame-size
    exit
    interface ethernet e1
    lldp med notifications topology-change enable
    exit
    interface ethernet e2
    lldp med notifications topology-change enable
    exit
    interface ethernet e3
    lldp med notifications topology-change enable
    exit
    interface ethernet e4
    lldp med notifications topology-change enable
    exit
    interface ethernet e5
    lldp med notifications topology-change enable
    exit
    interface ethernet e6
    lldp med notifications topology-change enable
    exit
    interface ethernet e7
    lldp med notifications topology-change enable
    exit
    interface ethernet e8
    lldp med notifications topology-change enable
    exit
    interface ethernet e9
    lldp med notifications topology-change enable
    exit
    interface ethernet e10
    lldp med notifications topology-change enable
    exit
    interface ethernet e11
    lldp med notifications topology-change enable
    exit
    interface ethernet e12
    lldp med notifications topology-change enable
    exit
    interface ethernet e13
    lldp med notifications topology-change enable
    exit
    interface ethernet e14
    lldp med notifications topology-change enable
    exit
    interface ethernet e15
    lldp med notifications topology-change enable
    exit
    interface ethernet e16
    lldp med notifications topology-change enable
    exit
    interface ethernet e17
    lldp med notifications topology-change enable
    exit
    interface ethernet e18
    lldp med notifications topology-change enable
    exit
    interface ethernet e19
    lldp med notifications topology-change enable
    exit
    interface ethernet e20
    lldp med notifications topology-change enable
    exit
    interface ethernet e21
    lldp med notifications topology-change enable
    exit
    interface ethernet e22
    lldp med notifications topology-change enable
    exit
    interface ethernet e1
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e2
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e3
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e4
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e5
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e6
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e7
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e8
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e9
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e10
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e11
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e12
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e13
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e14
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e15
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e16
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e17
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e18
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e19
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e20
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e21
    lldp med enable network-policy poe-pse
    exit
    interface ethernet e22
    lldp med enable network-policy poe-pse
    exit
    lldp med network-policy 1 voice vlan 111 vlan-type tagged
    interface range ethernet e(1-22)
    lldp med network-policy add 1
    exit
    interface vlan 199
    ip address 199.16.30.77 255.255.255.0
    exit
    ip default-gateway 199.16.30.3
    interface vlan 1
    no ip address dhcp
    exit
    no bonjour enable
    bonjour service enable csco-sb
    bonjour service enable http  
    bonjour service enable https 
    bonjour service enable ssh   
    bonjour service enable telnet
    hostname psw1
    line console
    exec-timeout 30
    exit
    line ssh
    exec-timeout 30
    exit
    line telnet
    exec-timeout 30
    exit
    management access-list Management1
    permit ip-source 10.22.5.5 mask 255.255.255.0
    exit
    logging 199.16.31.33 severity debugging description mysysloghost
    aaa authentication enable Console local
    aaa authentication enable SSH tacacs local
    aaa authentication enable Telnet local
    ip http authentication tacacs local
    ip https authentication tacacs local
    aaa authentication login Console local
    aaa authentication login SSH tacacs local
    aaa authentication login Telnet local
    line telnet
    login authentication Telnet
    enable authentication Telnet
    password admin
    exit
    line ssh
    login authentication SSH
    enable authentication SSH
    password admin
    exit
    line console
    login authentication Console
    enable authentication Console
    password admin
    exit
    username admin password admin level 15
    power inline usage-threshold 90
    power inline traps enable
    ip ssh server
    snmp-server location in-the-closet
    snmp-server contact [email protected]
    ip http exec-timeout 30
    ip https server
    ip https exec-timeout 30
    tacacs-server host 1.2.3.4 key spaceballz  timeout 3  priority 10
    clock timezone -7
    clock source sntp
    sntp unicast client enable
    sntp unicast client poll
    sntp server 199.16.30.1
    sntp server 199.16.30.2
    ip domain-name mydomain.com
    ip name-server  199.16.5.12 199.16.5.13
    ip telnet server

Maybe you are looking for

  • Can't pair Smartwatch with Galaxy Note ICS

    Hi, I am starting pairing procedure normally and I saw the code to smartwatch and phone but I soon as I press OK (to phone & smartwatch) the device is connected for half second and disconnected immediately !!  Any ideas ???

  • Cause Code 97, Error Class 2

    I have had my Droid Incredible 2 for a little over a month.  Has worked perfectly fine until this morning. I can receive messages, but whenever I try to reply to them I get a screen that says "Message failed. Would you like to retry?" but every time

  • Is Data Guard good option for Operational Reports

    One of our DBA has suggested to have data guard to produce real time or nearly real time(15 min. delay) operational reports, by which we can remove the load on OLTP system. Is it a good practice to use data guard for reporting purpose? what if Produc

  • Importing VCR/DVD to Mac via video camera - HELP

    Hello, I'm trying to transfer video from a dvd/vcr combo into iMovie, and can't get it to work. I have a Samsung DVD Recorder and VCR (DVD-VR375), and a Sony HandyCam. I've tried pretty much everything that I can think of to get the video capture to

  • Capture close event

    Hi, I have a scenario where I need to capture close event of active PDF document. I am opening a WinForm on click of toolbar button (in C++) and if user choose to close the PDF document, I want to close the WinForm at the same time. Please advice.