Bad clocks generated, with a locale with decimal comma

I noticed that I have to call 'vivado' with the LANG=C locale to get a decimal point, if I want the Clock Wizard in Vivado to work fine.
My system locale sets up decimal comma, but most numbers in vivado use decimal point. In the case of the Clock Wizard, if the Input Clock of the Zynq CPU is set to 33.33333MHz, it will do all PLL factors calculations considering it as 33MHz, causing major breakage in the built system.
For example, a request of 666MHz for the CPU clock would result in 676MHz.
(This is with Vivado 2014.4 on Linux)

I doubt vivado is tested on any localized OS so it's probably a good idea to stick with the North American settings

Similar Messages

SQL Loader with decimal commas

Dear All,
I am loading data for a German client and the delivered files contain numeric data with decimal commas. For example 123,5 instead of 123.5
I've been googling like mad on this one and there is a lot of chatter about setting NLS_LANG and/or NLS_NUMERIC_CHARACTERS but none of this seems to work in the SQL Loader environment.
I imagine that I will end up cobbling together a complicated thing with TO_NUMBER or with another function but I really can't believe that SQL Loader doesn't have a simple switch to flip from point to comma.
Or have I overlooked something?
Any tips would be a great help.
Regards,
Alan Searle

I am on a client's PC and don't have access to administrative settings.
And also, I cannot be sure that whoever runs the load function in the future will check this.
It is therefore important that I find a way to set this in SQL Loader without any other dependencies.
I think I will probably end up processing it as a string and then translating it to numeric. But this seems like a sledge hammer to crack a nut.
Regards and thanks,
Alan

Selection generated with Navigational Attribute and store forecast profile

Hi,
Our business has a requirement that will require for the solution a Forecast Profile to be stored against a selection which was generated with a navigational attribute in the selection. I have found two SAP Notes 329707 and 394076 shown below which point to BAdi /SAPAPO/SDP_FCST5 method SEL_CHANGE to do the job. Can anyone help me in understanding what coding we need to do within the BAdi to get this to work. Does anyone have an example?
SAP Note 329707
Method:
    SEL_CHANGE (as of SCM 4.1)
    This method can be used to change the selection to be stored in
    in the generated selection table. Navigation attributes can be
    removed, such as the function of assigning a forecast
    profile to the selection can also be allowed for selections with
    navigation attribute without a basic characteristic.
    Parameter
     IV_PAREAID      Importing Type /SAPAPO/TS_PAREAID
     CT_SELECTION    Changing   Type /SAPAPO/TS_IOBJ_SELECTION_TAB
Sample code:
    DATA: lv_tabix     TYPE sytabix.
    DATA: lt_chars     TYPE /sapapo/dm_int_chars_tab.
    DATA: ls_chars     TYPE /sapapo/dm_int_chars.
    DATA: ls_selection Type /SAPAPO/TS_IOBJ_SELECTION.
    IF iv_pareaid = 'PAREA1'.
      CALL FUNCTION '/SAPAPO/TS_PAREA_SINGLE_GET'
        EXPORTING
          iv_pareaid   = iv_pareaid
        IMPORTING
          et_chars     = lt_chars
        EXCEPTIONS
          not_found    = 1
          OTHERS       = 2.
      CHECK sy-subrc EQ 0.
      LOOP AT ct_selection INTO ls_selection
                          WHERE iobjnm NE '9AVERSION'.
        lv_tabix = sy-tabix.
        READ TABLE lt_chars INTO ls_chars
                            WITH KEY iobjnm = ls_selection-iobjnm.
        IF sy-subrc EQ 0 AND NOT ls_chars-atrnavfl IS INITIAL.
           DELETE ct_selection INDEX lv_tabix.
        ENDIF.
      ENDLOOP.
    ENDIF.
SAP Note 394076
As of Release SCM 4.1, you can use the method SEL_CHANGE of the BadI /SAPAPO/SDP_FCST5 to process the selection before saving it to the generated selection tables. This allows you to save selections with navigation attributes, for example, where the selections do not have a specified basis characteristic. You simply need to delete the navigation attributes from the selection.

Is all the Navigational attribute checked for display during cube creatiion?
Prathish

SNP purchase requisitions quantities generated with Decimals

HI Gurus,
When we run the location heuristics in SNP the purchase requisitions are (Distribution Receipts Planned ) are created without decimals.But when these are published to ECC the purchase requisitions are generated with decimals.For Example the SNP PR value is 15 and the ECC Pr is 15.200.How can i restrict this because i want the same quantity which is generated by SNP heuristics .Are there any settings in UOM(Unit of measure).I checked in the planning area for the key figure everthing is fine.
What are the settings to be made.
Dhanunjay.

The SNP might be generating 15.2 based on your lot sizing settings.
Most probably the reason you see 15( with no decimals) in SNP Planning book is because for your keyfigure, you have 0 decimals.
Go to Design mode for the plannning book, select the keyfigure and change the decimal places from 0 to 3(or any higher number)
Now you should be able to see 15.2 as stated in your example even in the plannning book
One other way to check would be in the product view(RRP3) or as someone already suggested( RRP2)
Thanks
Kumar

Reusing sessionid in url generated with wgateurl() to switch service

Hi all
In my Itsmobile application im not able to kill a calling session with ~singletransaction =1 or using the startservice described in below help
http://help.sap.com/saphelp_nw70/Helpdata/en/46/6c412141496a58e10000000a11466f/content.htm .
does any one know why i cant do this? is there a note? is this a basis issue?
on a side note i want to switch between ITS services without spawning another session in sm04 in ITSmobile application
so i thought if there was some way i could string process the url generated with wgateurl() & replace the old service with the new service then i would just be working in one session.
now my question is this the right thing to do? could this be bottlenecking the session memory?
& has any one done this using either HTML forBusiness or jscript?
any help would be highly appreciated
Prasad B

Hello,
is there someone out there who has experience with deploying JDeveloper SOAP Services with JBOSS?
I get one error after an other.
Here is just the next one:
2006-02-24 10:43:21,671 DEBUG [org.apache.catalina.loader.WebappClassLoader] Loading class from local repository
2006-02-24 10:43:21,671 INFO [org.apache.catalina.core.ContainerBase.[jboss.web].[localhost].[Engine]] Marking servlet testport as unavailable
2006-02-24 10:43:21,671 ERROR [org.apache.catalina.core.ContainerBase.[jboss.web].[localhost].[Engine]] Servlet /Engine threw load() exception
java.lang.ClassCastException: soap.service.connection.ServicePortal
     at org.apache.catalina.core.StandardWrapper.loadServlet(StandardWrapper.java:1048)
     at org.apache.catalina.core.StandardWrapper.load(StandardWrapper.java:925)
     at org.apache.catalina.core.StandardContext.loadOnStartup(StandardContext.java:3857)
     at org.apache.catalina.core.StandardContext.start(StandardContext.java:4118)
     at org.apache.catalina.core.ContainerBase.addChildInternal(ContainerBase.java:759)
     at org.apache.catalina.core.ContainerBase.addChild(ContainerBase.java:739)
     at org.apache.catalina.core.StandardHost.addChild(StandardHost.java:524)
The class soap.service.connection.ServicePortal is my Java RMI ServiceEndPoint (mapped name: Engine) with only one invoceable method and no class casts in it.
Hope that this monolog will get to an end and someone can help me.
best regards
Florian

Radio button on a from generated with PL/SQL procedure

Hi,
I have a form generated with PL/SQL procedure. This procedure calls another procedure on 'Submit'. If I select value for the radio button, it works fine. But if no value is given to the radio button on the form, it gives error. Is the radio button mandatory field by nature? or do I need to give default value some how? How do I make the radio button optional? so that I can call the next procedure without passing the param.
Create or Replace PROCEDURE OBM_PROCEDURE
htp.formOpen(OWA_UTIL.GET_OWA_SERVICE_PATH || 'process_obm');
htp.Print('Admin ');
htp.FormRadio('p_access_level','A');
htp.Print('Doc ');
htp.FormRadio('p_access_level','D');
htp.formSubmit(cname=>'p_button', cvalue=> 'Submit');
=================================================================
Create or Replace PROCEDURE PROCESS_OBM
(p_access_level VARCHAR2,
p_button VARCHAR2)
htp.Print('p_access_level ');
Thanks!

Hi
The parameters of the called procedure should have defualt values like this
create or Replace PROCEDURE PROCESS_OBM
(p_access_level VARCHAR2 default 1,
p_button VARCHAR2 default null
htp.Print('p_access_level ');
Thanks,
sharmila

How to avoid zeros in output for a field with Decimal type

Hi Friends
In a Report one output field is declared with decimal type.
Whenver that field is not filled with any values zeros will be displayed in the output.
I tried to change the data type to char but i am facing some issues in calculations and shwoing only 2 decimal places.
So is there any way to hide the zeros in the output if we the field is not filled with any value.

Hi Sandeep,
If required field type is declared as type p decimals 2 , if for that field in internal table there is no value - then automatically output will get display in ALV as 0.00.
To remove 0.00 in the output screen and to be displayed in blank then in the field catalogue add wa_fieldcat-no_zero = 'X'. in that particular field. then if no value for that field then it will display space in the output.
wa_fieldcat-fieldname   = 'ZQUAN'.
wa_fieldcat-seltext_l   = 'Quantity'.
wa_fieldcat-outputlen = '13'.
wa_fieldcat-no_out      = ' '.
wa_fieldcat-no_zero    = 'X'. wa_fieldcat-hotspot     = ' '.
wa_fieldcat-key            = ' '.
wa_fieldcat-do_sum      = 'X'.
wa_fieldcat-qfieldname = ' '.
wa_fieldcat-ref_tabname = ' '.
wa_fieldcat-just                = ' '.
Regards,
Priya

Conversion program generated with errors

in lsmw idoc method at the step 11 convert data iam getting error as conversion program generated with errors can some body help me .i assigned port ,partnertype and partner number and activated inbound processing but still getting this error.somebody pls help me its urgent.

Hi Mamidi,
Go to the LSMW you have choosen and if it is Recording Method you are getting this error.
Select Goto-->Recordings.
Select the Recording you have choosen in the Edit Mode.
Click on the Defaults All Button and save the recording.
Now go to the option Convert Data and check .
You will receive a message ..Conversion program successfully generated.
Thanks,
Sri

If pdf generated with Bullzip, opens with problems in text (missing, weird characters, etc...)

pdf opening in new tab shows problems with text. If pdf was generated with Adobe acrobat, works fine. If pdf generated with Bullzip, opens in new tab, but with problems.

hello lwhitman, the pdf preview in firefox is still under very active development. if you find any issues please report them at https://github.com/mozilla/pdf.js/issues & provide a sample pdf-file which shows the problem.

Exception obtained when invoking a web service generated with JDeveloper

Hello,
I tried to create a synchronous BPEL process that invokes synchronously a Java Web Service created with the JDeveloper. The web service is wrapped around a regular Java class. The new created BPEL process is successfully compiled and deployed on the server. But when I try to initiate a test instance of the process in the BPEL console, after I fill the input parameter for then process and push the "Post XML Message" button, I obtain the following error:
Your test request generated the following exception/fault:
BPEL Fault: {http://oracle.com/cde/util/Top300DAO.wsdl}org.apache.wsif.soap.fault{org.apache.wsif.soap.fault.object=java.net.ConnectException: Connection refused: connect}
I looked at flow and it throws the exception when it tries to invokes the web service generated with JDeveloper.
Do you have any hints, ideas? Thanks a lot in advance for your help.
I want to also say that the proxy settings for the BPEL server and designer are filled. I think that they are ok because I succeeded to start an instance of another process that calls synchronously an external Web Service.
Regards,
Marinel

My guess is that this is caused by the WSDL of your service having an invalid service address. Can you please take a look at the WSDL of your service make sure that the location of the address is valid? (we have seen a couple of instances in the past where the generated url did not have the right port information).
Update that WSDL, restart the BPEL server or from the BPEL console clear the WSDL cache and re-initiate your flow.
Best,
Edwin

Problem with decimal

Hi Experts,
I'm having a problem with decimal.
I have a alv data grid that can be edited.Once I press enter the value for the decimal fields are changed.
Example: If i input 5.00 in the field then I press enter it converts it to 0.05
And If I input 2.01 in the field it shows an error Too many decimal places(Maximum 0)
DATA INPUT for my internal table:
DATA: BEGIN OF it_data OCCURS 0,
   docno LIKE zit_haul_line-docno,
   line LIKE zit_haul_line-line,
   eqpno LIKE zit_haul_line-eqpno,
   rpt LIKE zit_haul_line-rpt,
   notrip LIKE zit_haul_line-notrip,
   trc LIKE zit_haul_line-trc,
   escfee LIKE zit_haul_line-escfee,
   tollfee LIKE zit_haul_line-tollfee,
   repr LIKE zit_haul_line-repr,
   others LIKE zit_haul_line-others,
   tba LIKE zit_haul_line-tba,
   dik LIKE zit_haul_line-dik,
   locorg LIKE zit_haul_line-locorg,
   locdes LIKE zit_haul_line-locdes,
END OF it_data.
DATA: wa_data LIKE it_data.
Here is my code in change ALV Change.
FORM data_changed USING ir_data_changed TYPE REF TO cl_alv_changed_data_protocol.
   DATA ls_modi TYPE lvc_s_modi.
   DATA: ratepertrip LIKE zit_haul_line-rpt,
         nooftrip LIKE zit_haul_line-notrip,
         lv_value TYPE lvc_value ,
         totalrent LIKE zit_haul_line-trc,
         escortfee LIKE zit_haul_line-escfee,
         tollfee LIKE zit_haul_line-tollfee,
         represent LIKE zit_haul_line-repr,
         others LIKE zit_haul_line-others,
         lv_value1 TYPE lvc_value,
         totalbill LIKE zit_haul_line-tba.
   DATA: eqpno LIKE equi-equnr,
         gv_equnr LIKE equi-equnr.
* Check each modification:
   LOOP AT ir_data_changed->mt_mod_cells INTO ls_modi.
      CASE ls_modi-fieldname.
       WHEN 'EQPNO'.
         CONDENSE ls_modi-value.
         SELECT SINGLE equnr
           INTO gv_equnr
           FROM equi
           WHERE equnr EQ ls_modi-value.
         IF sy-subrc NE 0.
           CALL METHOD ir_data_changed->add_protocol_entry
             EXPORTING
               i_msgid     = '00'
               i_msgty     = 'E'
               i_msgno     = '398'
               i_msgv1     = 'Equipment Number does not exist:'
               i_msgv2     = ls_modi-value
               i_msgv3     = ''
               i_msgv4     = ''
               i_fieldname = ls_modi-fieldname
               i_row_id    = ls_modi-row_id.
         ENDIF.
     ENDCASE.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'RPT'
     IMPORTING e_value = ratepertrip.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'NOTRIP'
     IMPORTING e_value = nooftrip.
   CLEAR totalrent.
     ls_modi-fieldname = 'TRC'.
     IF ratepertrip = ''.
       ratepertrip = 1.
     ELSEIF nooftrip = ''.
       nooftrip = 1.
     ENDIF.
     totalrent = ratepertrip * nooftrip.
     CALL METHOD ir_data_changed->modify_cell
       EXPORTING i_row_id = ls_modi-row_id
       i_fieldname = ls_modi-fieldname
       i_value = totalrent.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'ESCFEE'
     IMPORTING e_value = escortfee.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'TOLLFEE'
     IMPORTING e_value = tollfee.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'REPR'
     IMPORTING e_value = represent.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'OTHERS'
     IMPORTING e_value = others.
   CLEAR totalbill.
     ls_modi-fieldname = 'TBA'.
     totalbill = escortfee + tollfee + represent + others.
     totalbill = totalrent + totalbill.
     CALL METHOD ir_data_changed->modify_cell
       EXPORTING i_row_id = ls_modi-row_id
       i_fieldname = ls_modi-fieldname
       i_value = totalbill.
   ENDLOOP.
ENDFORM.                    "data_changed

Hi,
Can you check my code. I've tried changing the data types of my internal table and my output is stll same when I press enter.
The output should be 2.00 3.00 5.00 7.00
Also if I enter 12345.00 the output should be 12,345.00.
Thank you so much for the help.
* ALV required data objects.
TYPE-POOLS: sdydo, icon, slis.
DATA: w_title     TYPE lvc_title,
       w_repid     TYPE sy-repid,
       w_comm      TYPE slis_formname,
       w_status    TYPE slis_formname,
       x_layout    TYPE slis_layout_alv,
       ls_events   TYPE LINE OF slis_t_event,
       t_events    TYPE slis_t_event,
       t_fieldcat TYPE slis_t_fieldcat_alv,
       x_sort      type LINE OF slis_t_sortinfo_alv,
       t_sort      TYPE slis_t_sortinfo_alv,
       ls_heading TYPE slis_listheader,
       t_heading   TYPE slis_t_listheader,
       ls_fieldcat TYPE slis_fieldcat_alv,
       gs_variant LIKE disvariant,
        gt_events            TYPE slis_t_event,
        gs_events            TYPE slis_alv_event.
DATA:
   wa_layout     TYPE slis_layout_alv,
   wa_events         TYPE slis_alv_event,
   wa_sort TYPE slis_sortinfo_alv.
TYPES: BEGIN OF t_header,
        line01(555) TYPE c,
        line02(555) TYPE c,
        END OF t_header.
DATA: is_print TYPE slis_print_alv,
       gset TYPE lvc_s_glay,
       %runmode TYPE aqlimode.
data: it_sortcat   type slis_sortinfo_alv occurs 1.
DATA: gw_header TYPE t_header.
" END OF ALV DATA
"========================================================================================================================
DATA: BEGIN OF it_data OCCURS 0,
   docno LIKE zit_haul_line-docno,
   line LIKE zit_haul_line-line,
   eqpno LIKE zit_haul_line-eqpno,
   rpt TYPE p DECIMALS 2, "LIKE zit_haul_line-rpt,
   notrip TYPE p DECIMALS 2,
   trc TYPE p DECIMALS 2,
   escfee TYPE p DECIMALS 2,
   tollfee TYPE p DECIMALS 2,
   repr TYPE p DECIMALS 2,
   others TYPE p DECIMALS 2,
   tba TYPE p DECIMALS 2,
   dik LIKE zit_haul_line-dik,
   locorg LIKE zit_haul_line-locorg,
   locdes LIKE zit_haul_line-locdes,
END OF it_data.
DATA: wa_data LIKE it_data.
DATA: it_modified TYPE STANDARD TABLE OF zit_haul_line WITH HEADER LINE.
DATA: wa_modified TYPE STANDARD TABLE OF zit_haul_line WITH HEADER LINE.
SELECTION-SCREEN BEGIN OF BLOCK b1 WITH FRAME.
PARAMETERS: r_create RADIOBUTTON GROUP rad1 USER-COMMAND a DEFAULT 'X'.
   SELECTION-SCREEN BEGIN OF BLOCK b2 WITH FRAME.
   PARAMETERS: r_proj RADIOBUTTON GROUP rad2 MODIF ID A.
   PARAMETERS: r_cost RADIOBUTTON GROUP rad2 MODIF ID A.
   SELECTION-SCREEN END OF BLOCK b2.
PARAMETERS: r_post RADIOBUTTON GROUP rad1.
PARAMETERS: r_rev RADIOBUTTON GROUP rad1.
   SELECTION-SCREEN BEGIN OF BLOCK b3 WITH FRAME.
     PARAMETERS: p_docno LIKE mseg-belnr MODIF ID B,
                 p_post LIKE sy-datum MODIF ID B.
   SELECTION-SCREEN END OF BLOCK b3.
SELECTION-SCREEN BEGIN OF BLOCK b4 WITH FRAME.
PARAMETERS: p_trand LIKE sy-datum,
             p_cost LIKE csks-kostl,
             p_proj TYPE string,
             p_wbs TYPE string,
             p_nwa TYPE string.
SELECTION-SCREEN END OF BLOCK b4.
SELECTION-SCREEN END OF BLOCK b1.
AT SELECTION-SCREEN OUTPUT.
LOOP AT SCREEN.
   IF r_create = 'X'.
     IF screen-group1 = 'A'.
        screen-active = 1.
     ENDIF.
   ELSE.
     IF screen-group1 = 'A'.
        screen-active = 0.
     ENDIF.
   ENDIF.
   IF r_post = 'X' OR r_rev = 'X'.
     IF screen-group1 = 'B'.
        screen-active = 1.
     ENDIF.
   ELSE.
     IF screen-group1 = 'B'.
        screen-active = 0.
     ENDIF.
   ENDIF.
   MODIFY SCREEN.
ENDLOOP.
START-OF-SELECTION.
PERFORM get_data.
PERFORM display_report.
FORM get_data.
it_data-line = '001'.
APPEND it_data.
it_data-line = '002'.
APPEND it_data.
it_data-line = '003'.
APPEND it_data.
it_data-line = '004'.
APPEND it_data.
it_data-line = '005'.
APPEND it_data.
it_data-line = '006'.
APPEND it_data.
it_data-line = '007'.
APPEND it_data.
it_data-line = '008'.
APPEND it_data.
it_data-line = '009'.
APPEND it_data.
it_data-line = '010'.
APPEND it_data.
ENDFORM.
"ALV DISPLAY ====================================================================================================================================
"&      Form PF_WRITE_FIELDCAT
*&      Form pf_write_fieldcat
*       text
*      -->FNAME      text
*      -->TNAME      text
*      -->TEXT       text
*      -->LEN        text
FORM pf_write_fieldcat USING fname
                               tname
                               text
                               len
                               edt.
*                              key
*                              sum.
   ls_fieldcat-fieldname     = fname.
   ls_fieldcat-tabname       = tname.
   ls_fieldcat-seltext_l     = text.
   ls_fieldcat-outputlen     = len.
* ls_fieldcat-key           = key.
* ls_fieldcat-do_sum        = sum.
   ls_fieldcat-edit = edt.
   IF len = '0'.
     ls_fieldcat-outputlen     = '1'.
     ls_fieldcat-no_out = 'X'.
   ENDIF.
   APPEND ls_fieldcat TO t_fieldcat.
   CLEAR ls_fieldcat.
* To set ENTER Event!
   gs_events-name = 'CALLER_EXIT'.
   gs_events-form = 'CALLER_EXIT'.
   APPEND gs_events TO gt_events.
*   To change the ALV Changed Protocoll
   gs_events-name = 'DATA_CHANGED'.
   gs_events-form = 'DATA_CHANGED'.
   APPEND gs_events TO gt_events.
ENDFORM.                    " PF_WRITE_FIELDCAT
*&      Form display_report
FORM display_report.
   is_print-no_print_selinfos = 'X'.
   is_print-no_print_listinfos = 'X'.
   is_print-print_ctrl = 'X'.
   PERFORM pf_write_fieldcat USING:
* 'DOCNO'                  'IT_DATA' 'Line'                   ' ' '',
   'LINE'                  'IT_DATA' 'Line'                   ' ' '',
   'EQPNO'                 'IT_DATA' 'Equipment No.'          ' ' 'X',
   'RPT'           'IT_DATA' 'Rate per Trip'          ' ' 'X',
   'NOTRIP'              'IT_DATA' 'No of Trip'             ' ' 'X',
   'TRC'             'IT_DATA' 'Total Rental Charges'   ' ' '',
   'ESCFEE'             'IT_DATA' 'Escort Fee'             ' ' 'X',
   'TOLLFEE'               'IT_DATA' 'Toll Fee'               ' ' 'X',
   'REPR'             'IT_DATA' 'Representation'         ' ' 'X',
   'OTHERS'                'IT_DATA' 'Others'                 ' ' 'X',
   'TBA'               'IT_DATA' 'Total Billable Amount' ' ' '',
   'DIK'              'IT_DATA' 'Distance in KM'         ' ' 'X',
   'LOCORG'             'IT_DATA' 'Location Origin'        ' ' 'X',
   'LOCDES'             'IT_DATA' 'Location Destination'   ' ' 'X'.
* Layout
   x_layout-zebra = 'X'.
   x_layout-no_keyfix = ' '.
   x_layout-colwidth_optimize = 'X'.
* GUI Status
   w_status = 'SET_PF_STATUS'.
   w_repid = sy-repid.
* User commands
   w_comm = 'USER_COMMAND'.
* gs_variant-variant = p_var1.
* gs_variant-handle = space.
* gs_variant-report = sy-repid.
   gs_variant-report = sy-repid.
   gs_variant-username = sy-uname.
   gset-no_colwopt = 'X'.
* Displays the ALV grid
   CALL FUNCTION 'REUSE_ALV_GRID_DISPLAY'
     EXPORTING
       i_callback_program = sy-repid
       it_fieldcat        = t_fieldcat
       is_layout          = x_layout
       "it_sort            = t_sort
       it_sort                 = it_sortcat
*      i_callback_pf_status_set = w_status
       "i_callback_user_command = w_comm
       I_CALLBACK_USER_COMMAND = 'USER_COMMAND'
*      i_callback_html_top_of_page = 'TOP_OF_PAGE'
       i_callback_top_of_page = 'TOP-OF-PAGE'
*      i_callback_html_end_of_list = 'END-OF-PAGE'
       is_variant         = gs_variant
       i_save             = 'A'
       is_print           = is_print
       it_events          = gt_events
*      i_grid_title       = w_title
     TABLES
       t_outtab           = IT_DATA
     EXCEPTIONS
       program_error      = 1
       OTHERS             = 2.
ENDFORM.                    " display_report
FORM data_changed USING ir_data_changed TYPE REF TO cl_alv_changed_data_protocol.
   DATA ls_modi TYPE lvc_s_modi.
   DATA: ratepertrip LIKE zit_haul_line-rpt,
         nooftrip LIKE zit_haul_line-notrip,
         lv_value TYPE lvc_value ,
         totalrent LIKE zit_haul_line-trc,
         escortfee LIKE zit_haul_line-escfee,
         tollfee LIKE zit_haul_line-tollfee,
         represent LIKE zit_haul_line-repr,
         others LIKE zit_haul_line-others,
         lv_value1 TYPE lvc_value,
         totalbill LIKE zit_haul_line-tba.
   DATA: eqpno LIKE equi-equnr,
         gv_equnr LIKE equi-equnr.
* Check each modification:
   LOOP AT ir_data_changed->mt_mod_cells INTO ls_modi.
      CASE ls_modi-fieldname.
       WHEN 'EQPNO'.
         CONDENSE ls_modi-value.
         SELECT SINGLE equnr
           INTO gv_equnr
           FROM equi
           WHERE equnr EQ ls_modi-value.
         IF sy-subrc NE 0.
           CALL METHOD ir_data_changed->add_protocol_entry
             EXPORTING
               i_msgid     = '00'
               i_msgty     = 'E'
               i_msgno     = '398'
               i_msgv1     = 'Equipment Number does not exist:'
               i_msgv2     = ls_modi-value
               i_msgv3     = ''
               i_msgv4     = ''
               i_fieldname = ls_modi-fieldname
               i_row_id    = ls_modi-row_id.
         ENDIF.
     ENDCASE.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'RPT'
     IMPORTING e_value = ratepertrip.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'NOTRIP'
     IMPORTING e_value = nooftrip.
   CLEAR totalrent.
     ls_modi-fieldname = 'TRC'.
     IF ratepertrip = ''.
       ratepertrip = 1.
     ELSEIF nooftrip = ''.
       nooftrip = 1.
     ENDIF.
     totalrent = ratepertrip * nooftrip.
     CALL METHOD ir_data_changed->modify_cell
       EXPORTING i_row_id = ls_modi-row_id
       i_fieldname = ls_modi-fieldname
       i_value = totalrent.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'ESCFEE'
     IMPORTING e_value = escortfee.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'TOLLFEE'
     IMPORTING e_value = tollfee.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'REPR'
     IMPORTING e_value = represent.
   CALL METHOD ir_data_changed->get_cell_value
     EXPORTING i_row_id = ls_modi-row_id
     i_fieldname = 'OTHERS'
     IMPORTING e_value = others.
   CLEAR totalbill.
     ls_modi-fieldname = 'TBA'.
     totalbill = escortfee + tollfee + represent + others.
     totalbill = totalrent + totalbill.
     CALL METHOD ir_data_changed->modify_cell
       EXPORTING i_row_id = ls_modi-row_id
       i_fieldname = ls_modi-fieldname
       i_value = totalbill.
   ENDLOOP.
ENDFORM.                    "data_changed
FORM caller_exit USING is_data TYPE slis_data_caller_exit.
* Switch to OO_ALV:
   DATA: lr_alv TYPE REF TO cl_gui_alv_grid.
   CALL FUNCTION 'GET_GLOBALS_FROM_SLVC_FULLSCR'
     IMPORTING
       e_grid = lr_alv.
* Register ENTER as edit event:
   CALL METHOD lr_alv->register_edit_event
     EXPORTING
       i_event_id = cl_gui_alv_grid=>mc_evt_enter.
* pls. use MC_EVT_MODIFIED if leaving the cell should trigger the edit event!
ENDFORM. "CALLER_EXIT
*&      Form TOP-OF-PAGE
*       text
FORM top-of-page.
*ALV Header declarations
   DATA: t_header TYPE slis_t_listheader,
         wa_header TYPE slis_listheader,
         t_line LIKE wa_header-info,
         ld_lines TYPE i,
         ld_linesc(10) TYPE c.
   DATA: text TYPE sdydo_text_element,
         a_right   TYPE REF TO cl_dd_area.
   DATA: tran TYPE string,
         send TYPE string,
         wbs TYPE string,
         nwa TYPE string.
   text = 'Create Hauling Charges for Project'.
   wa_header-typ = 'S'.
   wa_header-info = text.
   APPEND wa_header TO t_header.
   CLEAR: wa_header.
   gw_header-line01 = text.
   CONCATENATE 'Transaction Date: ' p_trand INTO tran SEPARATED BY space.
   text = tran.
   wa_header-typ = 'S'.
   wa_header-info = text.
   APPEND wa_header TO t_header.
   CLEAR: wa_header.
   gw_header-line01 = text.
   CONCATENATE 'Sender Cost Center: ' p_cost INTO send SEPARATED BY space.
   text = send.
   wa_header-typ = 'S'.
   wa_header-info = text.
   APPEND wa_header TO t_header.
   CLEAR: wa_header.
   gw_header-line01 = text.
   CONCATENATE 'Receiver WBS: ' p_wbs INTO wbs SEPARATED BY space.
   text = wbs.
   wa_header-typ = 'S'.
   wa_header-info = text.
   APPEND wa_header TO t_header.
   CLEAR: wa_header.
   gw_header-line01 = text.
   CONCATENATE 'Receiver Network and NWA: ' p_nwa INTO nwa SEPARATED BY space.
   text = nwa.
   wa_header-typ = 'S'.
   wa_header-info = text.
   APPEND wa_header TO t_header.
   CLEAR: wa_header.
   gw_header-line01 = text.
   CALL FUNCTION 'REUSE_ALV_COMMENTARY_WRITE'
     EXPORTING
       it_list_commentary = t_header.
ENDFORM.                    "top-of-page
FORM pf_set_top_page_heading USING typ
                                     key
                                     info.
   ls_heading-typ = typ.
   ls_heading-key = key.
   ls_heading-info = info.
   APPEND ls_heading TO t_heading.
ENDFORM.                    " PF_SET_TOP_PAGE_HEADING
*&      Form PF_SET_TOP_PAGE_EVENTS
FORM pf_set_top_page_events USING name
                                    form.
   ls_events-name = name.
   ls_events-form = form.
   APPEND ls_events TO t_events.
   CLEAR ls_events.
ENDFORM.                    " PF_SET_TOP_PAGE_EVENTS
*&      Form REUSE_ALV_GET_VARIANT
FORM reuse_alv_get_variant
   USING    value(iv_repid)   TYPE sy-repid
            value(iv_handle) TYPE slis_handl
   CHANGING iv_variant        TYPE disvariant-variant.
   DATA: lv_exit(1) TYPE c,
         ls_variant TYPE disvariant.   " Structure for Variant
   MOVE: iv_variant TO ls_variant-variant,
         iv_handle TO ls_variant-handle,
         iv_repid   TO ls_variant-report.
   CALL FUNCTION 'REUSE_ALV_VARIANT_F4'
     EXPORTING
       is_variant    = ls_variant
       i_save        = 'A'
     IMPORTING
       e_exit        = lv_exit
       es_variant    = ls_variant
     EXCEPTIONS
       not_found     = 1
       program_error = 2
       OTHERS        = 3.
   IF sy-subrc <> 0.
     MESSAGE ID sy-msgid TYPE sy-msgty NUMBER sy-msgno
             WITH sy-msgv1 sy-msgv2 sy-msgv3 sy-msgv4.
   ENDIF.
   IF lv_exit = space.
     MOVE ls_variant-variant TO iv_variant.
   ENDIF.
ENDFORM.                    " REUSE_ALV_GET_VARIANT                 "
FORM user_command USING w_ucomm LIKE sy-ucomm
rs_selfield TYPE slis_selfield.
CASE w_ucomm.
WHEN '&DATA_SAVE'.
* READ TABLE it_data INTO wa_data." INDEX rs_selfield-tabindex.
   DELETE it_data WHERE eqpno IS INITIAL.
   LOOP AT it_data INTO wa_data.
     CONDENSE wa_data-eqpno.
     MOVE-CORRESPONDING wa_data TO wa_modified.
     APPEND wa_modified TO it_modified.
   ENDLOOP.
   MODIFY zit_haul_line FROM TABLE it_modified.
ENDCASE.
ENDFORM. "user_command

Problem with decimal point in Korea and Japan

Hi all,
I have one problem with decimal points.
I need to change in my out put cuurency values as per japan or korea standards.
Please help me is there any function module for this one.
program using alv grid display.
i use write statement but it is not working. Because
data: L_AMT type glpca-hsl,
         G_AMT TYPE CHAR15.
CURR this value is 'JPY'.
WRITE L_AMT CURRENCY CURR TO G_AMT.
here i need to do
L_AMT = G_AMT.   "" going to runtime error.
if i taken like
data: L_AMT TYPE CHAR15,
         G_AMT TYPE CHAR15.
CURR this value is 'JPY'.
WRITE L_AMT CURRENCY CURR TO G_AMT.   "" it is not working
Regards
margani

Hello,
This is pretty basic, whenever you've currency & quantity fields you need to pass the corres. reference fields.
In your case you need to populate the cfieldname & ctabname fields of the FieldCat.
BR,
Suhas

TOC Does Not Open in WebHelp Generated with RoboHelp 11

The TOC does not open in WebHelp Generated with RoboHelp 11. I tried other solutions posted on this forum but no success. Any ideas? Thanks in advance for your assistance.

Hi Jeff,
Thanks for responding! I uninstalled and reinstalled RoboHelp 11 and the WeHelp appears to display OK now. BUT, I have graphics in my project that are not displaying, only the empty placeholder for the graphics. This was displaying fine in WebHelp generated with RoboHelp 9 but not now. I see the graphics when I do “Preview Topic” but not in the generated WebHelp. Any clues what is causing this behavior? How can I correct it?
My tables appear very strange too. They are the default table in RoboHelp with the raised gray/silver border. However, in WebHelp, the tables appear as double solid black lines for the border. The tables appear fine in the topic but when viewed via “Preview Topic” and WebHelp output, they are double black likes. Help!
Another thing is that I also get an occasional message about a topic that says “The reference to the file contains illegal characters and will not be shown in Project Manager. How can this be? My css is valid and I use it in numerous help projects.
Once again, thanks so much for your willingness to help. It is much appreciated.

Created a pdf file showing a graph generated with CL_GUI_CHART_ENGINE

Hi Experts!
Please, anyone has already created a pdf file showing a graph generated with CL_GUI_CHART_ENGINE??
Could anyone help me with this requirement?
Thanks in advance,
Best regards

Hi,
I searched and found another solution, because with the code from the link above I got everytime a short dump, maybe I did something wrong.
The solution works with Adobe Form
1. I used the class cl_igs_chart_engine to create a chart with my data and customizing to get the binary data of the image.
2. Convert the binary tab to xstring.
3. You can use this xstring on the Adobe Form to display the image.
Maybe the following tips are useful.
*How to get the data of chart you can see in the class
CL_TIME_CHART_SIMPLE (use cl_gui_chart_engine for the chart but class cl_igs_chart_engine for saving the image)
*How to bind the image to the importing parameter (xstring)
/people/thomas.jung3/blog/2005/07/13/lessons-learned-from-adobe-forms-development
Regards

Smartforms - dealing with decimal and thousand separators

Hi,
trying to reuse one of the standard SAP Smartforms - LB_BIL_INVOICE in an ECC 6.0 Unicode system I faced a problem with decimal and thousand separators for currency/quantity fields. In fact, default settings in User profile are not taken in consideration when printing this form. I have changed all the possible settings in the user profife and (after logoff/logon) nothing changes in my output.
Just to be sure I tried to output the invoice with the original SAP smartform LB_BIL_INVOICE and the things were the same - means output takes wrong settings for decimal/thousand separators.
For clarity I created a simple form with a single currency field and everything behaves well as expected. So this points me to the direction fo find out what is wrong with the LB_BIL_INVOICE. I downloaded the form into XML and checked the code, further uploaded it into a new one - no success.
My question is:
Is there a way to manipulate or overwrite default settings for decimal/thousand separators within smartform, and if yes - how to do this?
I almost finished my quite complex form and wouldn't like to rewrite it from scratch.
FYI: I'm not a Smartform expert, by have created/overwiten more than 15 different forms accros different systems - 4.6 C/D, 4.7, ECC 6.0 non-Unicode/Unicode, and never faced such an issue.
I faced significant smartform 'improvement' in the ECC 6.0 release - especialy for text elements. The new integrated MS word control gives me a lot of throubles. According to this - is there an up-to-date documentation (even link to SAP course is acceptable) according to Smartform development in ECC 6.0?
Thanks in advance.
Regards,
Ivaylo Mutafchiev
Senior SAP Abap Consultant

Hi,
I took a quick glance into the print program, and the print program do a set country setting to reciving country. This will give you the separators that are confugured for this country.
But if you change the print program and clear parameter country, the smartform will use the users settings instead.
Regards
Åsa Thenstedt

Bad clocks generated, with a locale with decimal comma

Similar Messages

Maybe you are looking for