Battery state not updating
ok so I'm running arch linux on my laptop (Lenovo IdeaPad 510 G) and I've got a problem wit my battery, it doesn't update it's state to power managers (meaning that both xfce power manager and batti get an initial reading when I turn my laptop on but then they stop updating the battery state, so if I start my laptop with 100% battery that is what they will show for the whole session even if it drops to 1%), I've checked the wiki and tried using acpi, neither the battery nor the ac modules run but when I use acpi -i I do get my correct battery state.
I'm starting to run out of ideas here, has anyone faced this kind of problem before?
This is due to a recent upower update. upower 0.99 uses a whole new set of api's which means that all the power managers need to be updated to work with it. I had the exact same issue on MATE but mate-power-manager got patched yesterday which fixed the issue. Until xfce4-power-manager is patched, you'll need to use an alternative battery applet that does work with the new upower (if there is one) or downgrade to an older version of upower. Here's the link if you want to downgrade: http://seblu.net/a/arm/2014/03/31/extra/os/x86_64/
EDIT: Don't bother downgrading upower. The issue has already been reported: https://bugs.archlinux.org/task/39893
and a new version of xfce4-power-manager which fixes the issue is in the testing repo: https://www.archlinux.org/packages/test … r-manager/
Last edited by Chazza (2014-04-26 15:05:45)
Similar Messages
-
Hi everybody
I have a Acer Aspire 5820TG TimelineX which is a really good laptop. But I have a big problem. I can't read the state of the battery.
This is what I get from acpi -V,
Battery 0: Unknown, 0%, rate information unavailable
Battery 0: design capacity 4400 mAh, last full capacity 4400 mAh = 100%
Adapter 0: on-line
Thermal 0: ok, 40.0 degrees C
Thermal 0: trip point 0 switches to mode critical at temperature 105.0 degrees C
Thermal 0: trip point 1 switches to mode passive at temperature 98.0 degrees C
Cooling 0: LCD 0 of 9
Cooling 1: LCD 0 of 9
Cooling 2: Processor 0 of 10
Cooling 3: Processor 0 of 10
Cooling 4: Processor 0 of 10
Cooling 5: Processor 0 of 10
from /proc/acpi/battery/BAT1/state
present: yes
design capacity: 4400 mAh
last full capacity: 4400 mAh
battery technology: rechargeable
design voltage: 11100 mV
design capacity warning: 300 mAh
design capacity low: 132 mAh
cycle count: 0
capacity granularity 1: 32 mAh
capacity granularity 2: 32 mAh
model number: BAT1
serial number: 11
battery type: 11
OEM info: 11
As you can see, ACPI is well aware that the battery is present and its infomation
Some output from dmesg | grep ACPI if it helps
BIOS-e820: 00000000bb73b000 - 00000000bb7bf000 (ACPI NVS)
BIOS-e820: 00000000bb7e1000 - 00000000bb7ff000 (ACPI data)
modified: 00000000bb73b000 - 00000000bb7bf000 (ACPI NVS)
modified: 00000000bb7e1000 - 00000000bb7ff000 (ACPI data)
ACPI: RSDP 00000000000fe020 00024 (v02 ACRSYS)
ACPI: XSDT 00000000bb7fe120 0007C (v01 ACRSYS ACRPRDCT 00000001 01000013)
ACPI: FACP 00000000bb7fc000 000F4 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: DSDT 00000000bb7ed000 0BA9D (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: FACS 00000000bb75f000 00040
ACPI: ASF! 00000000bb7fd000 000A5 (v32 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: HPET 00000000bb7fb000 00038 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: APIC 00000000bb7fa000 0008C (v02 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: MCFG 00000000bb7f9000 0003C (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: SLIC 00000000bb7ec000 00176 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: BOOT 00000000bb7e9000 00028 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: ASPT 00000000bb7e5000 00034 (v04 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: WDAT 00000000bb7e4000 00224 (v01 ACRSYS ACRPRDCT 00000001 1025 01000013)
ACPI: SSDT 00000000bb7e3000 009F1 (v01 PmRef CpuPm 00003000 INTL 20051117)
ACPI: SSDT 00000000bb7e1000 01E0F (v01 AmdRef AmdTabl 00001000 INTL 20051117)
ACPI: Local APIC address 0xfee00000
ACPI: PM-Timer IO Port: 0x408
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x04] enabled)
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x05] enabled)
ACPI: LAPIC (acpi_id[0x05] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x06] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x07] lapic_id[0x00] disabled)
ACPI: LAPIC (acpi_id[0x08] lapic_id[0x00] disabled)
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
ACPI: HPET id: 0x8086a201 base: 0xfed00000
#6 [0000012000 - 0000016000] ACPI WAKEUP
ACPI: Core revision 20100121
ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
ACPI: bus type pci registered
ACPI: EC: Look up EC in DSDT
ACPI: Executed 1 blocks of module-level executable AML code
ACPI: BIOS _OSI(Linux) query ignored
ACPI: SSDT 00000000bb691c18 003AE (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
ACPI: SSDT 00000000bb68f018 00891 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
ACPI: SSDT 00000000bb690a98 00303 (v01 PmRef ApIst 00003000 INTL 20051117)
ACPI: SSDT 00000000bb68ed98 00119 (v01 PmRef ApCst 00003000 INTL 20051117)
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: EC: GPE = 0x16, I/O: command/status = 0x66, data = 0x62
ACPI: No dock devices found.
PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
ACPI: PCI Root Bridge [PCI0] (0000:00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P2._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
ACPI: PCI Root Bridge [CPBG] (0000:7f)
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 *7 10 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 *5 6 7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 11 12 14 15) *10
ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 *7 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
ACPI: PCI Interrupt Link [LNKH] (IRQs 1 3 4 5 6 7 *11 12 14 15)
PCI: Using ACPI for IRQ routing
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 11 devices
ACPI: ACPI bus type pnp unregistered
pcieport 0000:00:01.0: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:01.0: Failed to receive control of PCIe PME service: ACPI _OSC failed
pcieport 0000:00:1c.0: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.0: Failed to receive control of PCIe PME service: ACPI _OSC failed
pcieport 0000:00:1c.5: Requesting control of PCIe PME from ACPI BIOS
pcieport 0000:00:1c.5: Failed to receive control of PCIe PME service: ACPI _OSC failed
ACPI: resource 0000:00:1f.3 [io 0x4000-0x401f] conflicts with ACPI region SMBI [io 0x4000-0x400f 64bit pref disabled]
ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
ACPI: Power Button [PWRB]
ACPI: Lid Switch [LID0]
ACPI: Sleep Button [SLPB]
ACPI: Power Button [PWRF]
ACPI: Thermal Zone [_TZ] (40 C)
ACPI: AC Adapter [ACAD] (on-line)
ACPI: Battery Slot [BAT1] (battery present)
ACPI: WMI: Mapper loaded
ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[Firmware Bug]: ACPI(PEGP) defines _DOD but not _DOS
ACPI: Video Device [PEGP] (multi-head: yes rom: no post: no)
[Firmware Bug]: Duplicate ACPI video bus devices for the same VGA controller, please try module parameter "video.allow_duplicates=1"if the current driver doesn't work.
I'm using the latest kernel from [testing] (2.6.34-ARCH).docwario wrote:you should try to update the bios with the latest one from acer (actually 1.13),
battery state is now available
I updated BIOS to v1.15 - still no solution. I have, however, found out why I can't see if the battery is charged or not. Appearantly, Acer is not using the standard ACPI spec. Just look at this:
Intel ACPI Component Architecture
ASL Optimizing Compiler version 20100121 [Feb 6 2010]
Copyright (c) 2000 - 2010 Intel Corporation
Supports ACPI Specification Revision 4.0
dsdt.dsl 5231: Method (_Q0E, 0, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (_Q0E)
dsdt.dsl 6596: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 6600: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 6659: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 6663: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 6831: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 6835: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 6894: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 6898: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 7777: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 7870: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 7874: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 7941: Name (_T_2, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_2)
dsdt.dsl 8008: Method (OEMN, 0, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (OEMN)
dsdt.dsl 8105: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 9124: Name (_T_0, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_0)
dsdt.dsl 9152: Name (_T_1, Zero)
Remark 5111 - Use of compiler reserved name ^ (_T_1)
dsdt.dsl 9182: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 9248: Method (_WED, 1, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (_WED)
dsdt.dsl 9248: Method (_WED, 1, NotSerialized)
Warning 1081 - ^ Reserved method must return a value (_WED)
dsdt.dsl 9254: Return (OEMN ())
Warning 1093 - ^ Called method may not always return a value
dsdt.dsl 9399: Method (WMBH, 3, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (WMBH)
dsdt.dsl 9456: Method (WMBI, 3, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (WMBI)
dsdt.dsl 9518: Method (WMBJ, 3, NotSerialized)
Warning 1088 - ^ Not all control paths return a value (WMBJ)
dsdt.dsl 9616: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
dsdt.dsl 9661: Name (_T_0, Zero)
Remark 5111 - ^ Use of compiler reserved name (_T_0)
ASL Input: dsdt.dsl - 12143 lines, 396315 bytes, 5129 keywords
AML Output: dsdt.aml - 47766 bytes, 1103 named objects, 4026 executable opcodes
Compilation complete. 0 Errors, 8 Warnings, 18 Remarks, 6 Optimizations
So I properly need to make a correct DSDT table to solve my problem. However, I can't make heads or tails in the ACPI spec document, and most infomation about such a issue is highly outdated. -
2610 signal & battery state not visible
The display on my 2610 is difficult to see in bright light. I have set contrast to maximum and selected the basic theme to get black on white however the battery state and signal strength bars are still in light blue which is impossible to see in bright light. How do I change the colour of the bars to black?
go to display settings and you can select diff colours
If i have helped at all a click on the white star below would be nice thanks.
Now using the Lumia 1520 -
I have recently replaced the battery for my IPhone5 after a crash. After that the battery status indicator is not dynamically updating. It updates only after every restart. I tried resetting all settings, updated to recent IOS7.1, restored several times. But of no use. Please guide.
Hi,
I have the same problem with my now replaced iPhone 3G with iOS4...
I have this problem, when I charge my iPhone 3G with the charger, that was supplied with my iPad. And also the problem can only be solved, when rebooting the phone.
When charging, the symbol shows the "flash"-sign in the battery to show, that the iPhone is charging and the symbol changes to the wall-connector-symbol, after the iPhone has fully charged. But when disconnecting the charger, the battery-symbol still shows empty, until I reboot.
The problem occurs with the iPad charger, but it does not occur, when charging the iPhone inside my "JBL radial" soundspeaker-system.
So I think about a bug in iOS4
Regards,
Florian -
Battery status not updating when jacked
With the latest update to iOS4 (4.01 is it?) I noticed something that's really bothering me.
Whenever I charge my iPhone via a wall jack, the battery status image, both on the lockscreen and up in the corner, is frozen. If I was in the red it will stay the same.
The only way I can see if the phone is charged is the fact that the small image up in the corner changes to show the wall plug as usual. However if I unplug the phone, it still shows an empty battery.
This is solved by rebooting my iPhone.
Also note that this does NOT happen if I charge it through my PC or MacBook USB ports.
Why is this happening and how do I solve it?Hi,
I have the same problem with my now replaced iPhone 3G with iOS4...
I have this problem, when I charge my iPhone 3G with the charger, that was supplied with my iPad. And also the problem can only be solved, when rebooting the phone.
When charging, the symbol shows the "flash"-sign in the battery to show, that the iPhone is charging and the symbol changes to the wall-connector-symbol, after the iPhone has fully charged. But when disconnecting the charger, the battery-symbol still shows empty, until I reboot.
The problem occurs with the iPad charger, but it does not occur, when charging the iPhone inside my "JBL radial" soundspeaker-system.
So I think about a bug in iOS4
Regards,
Florian -
Battery Apps not updating on lockscreen
Hey everyone...
I have been using my Lumia 620 for a month now. But, I still haven't understood one thing.
I tried installing around 3-4 Battery apps so that I can see my battery status on the lockscreen. None of them update themselves, even after many hours.
However, when I keep my data or wifi connection ON, I can see them updating every 30 min.
So, my questions are:
1. Do all battery apps require internet to update battery status on lockscreen?
2. Why does it work that way when apps on other platforms like android can update the same offline?? Is there any workaround?fishy17 wrote:
Hey everyone...
I have been using my Lumia 620 for a month now. But, I still haven't understood one thing.
I tried installing around 3-4 Battery apps so that I can see my battery status on the lockscreen. None of them update themselves, even after many hours.
However, when I keep my data or wifi connection ON, I can see them updating every 30 min.
So, my questions are:
1. Do all battery apps require internet to update battery status on lockscreen?
2. Why does it work that way when apps on other platforms like android can update the same offline?? Is there any workaround?
You've answered your question really. It's just the way WP works. A data connection is required for updates to occur every 30 minutes. And please don't try and compare WP with Android as they are two completely different operating systems and work completely differently to each other. -
Hi,
I have states in one MXML page.
<mx:State name="show_dialog">
<mx:SetProperty target="{videoBusycursor}" name="includeInLayout" value="true"/>
</mx:State>
<mx:State name="hide_dialog">
<mx:SetProperty target="{videoBusycursor}" name="includeInLayout" value="false"/>
</mx:State>
When i use them in the root tag as currentState = "show_dialog" it works fine.
But when i try to set the state from some other mxml or class file without specifying in the root tag it is not working. Is there any function to trigger the state explicitly in flex. I was struck with this behvaiour.
Regards,
Jayagopal.johnnymac wrote:
I'm in Maine and having the same problem- what did you find out?
In some cases number can go quickly. Please contact customer support and ask them when they think numbers will be available and you can also check from time to time as well, because, normally they are refreshed often.
Please contact customer support: https://support.skype.com/en/faq/FA1170/How-can-I-contact-Skype-Customer-Service
Note: In some cases you can use a live chat with them: http://support.skype.com/en/support_selection
About Me You can also use a IP Camera as your camera for Skype video Example Instructions -
My blackberry messenger status's don't update? I don't know what to do or how to fix it?? HELP PLEASE!!!
Are you speaking of your reading other users status updates?
Give it time, it's been slow now for some users for about the last six weeks.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code -
IPhone 5 keeps restarting itself and battery not updating
So basically:
I opened up the control center yesterday and clicked Play on the music and the phone switched itself off then back on. Ever since then, it's gone crazy... Bare in mind this is a new replacement and I'm booked in at Apple on Thursday but that's a long time to go with a non-working piece of ****.
So anyway;
The iPhone restarts itself (comes up with grey/green lines on the screen then turns itself off/on).
The battery will not update, I could leave it charging for literally all day and it'd stay at 1% but if I restart the phone, only then will it update.
I have tried resetting the phone, setting up as new etc but the same problem occurs...
Any guidance right now? I can't deal with this for another 6 days... Thanks.The battery is dead. You need to change the battery.
-
Hi
I recently bought a new genuine battery for my MacBook Core Duo 2Ghz.
I wanted to make sure I get the most from the battery so I checked to see if it needed updating, which it does.
I downloaded 'Battery Update 1.4' and went through installation fine and it rebooted the laptop.
However, when I goto system profiler the 'Pack Lot Number' is still 0000 and should be 0003 after the update.
Also the firmware is 102 but should be 110 or higher.
Im confused as to why it's not updating and im now worried that I have spent a fair bit of money on a battery thats gunna fail again in a few months....
Can anyone help?SMC reset
SMC reset
Shut down the computer.
Plug in the MagSafe power adapter to a power source, connecting it to the Mac if its not already connected.
On the built-in keyboard, press the (left side) Shift-Control-Option keys and the power button at the same time.
Release all the keys and the power button at the same time.
Press the power button to turn on the computer.
Note: The LED on the MagSafe power adapter may change states or temporarily turn off when you reset the SMC. -
Any ideas on how to fix ipad after the new iOS 7 update? My battery will not charge, my ipad is hot to the touch, the iTunes Store won't open, and my messages on Facebook aren't showing up when I chat and pintrest won't pin to my boards.
If you have all your music on the cmputer then i would connect up my phone uncheck the Sync Music option and apply.
This should take all the music off your phone .Then you can resync the music back on to it.
If this doesn't work maybe a restore to factory settings and start from scratch is the way to go -
Macbook 4,1
Early 2008 15" macbook pro
Running Snow Leopard
the Battery was not working after only 23 cycles
I tried the Battery update and now it will not boot at all
I really do not want to loose my data on the drive
panic message is
Unable to find driver for this platform: "ACPI".\n"@/SourceCache/xnu/xnu-1228/iokit/Kernel/IOPlatformExpert.cpp:1378
Please helpPanic Message
panic(cpu 0 caller 0x000x563ebd) : Unable to find driver for this platform:
"ACPI".\n"@/SourceCache/xnu/xnu-1228/iokit/Kernel/IOPlatformExpert.cpp:1378
Debugger called: <panic>
Backtrace (CPU 0), Format - Frame : Return Address (4 potential args on stack)
(7 lines of hex)
BSD Process name corresponding to current thread: Unkonwn
Kernel version:
Darwin Kernel Version 10.8.0" todays date ; root:xnu-1504.15.3~1/release_I386
I tried to boot from CD can, but i dont want to loose any information.
Tried disk tools
Hardware test
Tried to check if it was memory sticks failing or battery , nothing else plugged in
if i boot holding Apple key and S
I get additional warnings about AppleACPIPlatform and not being able to load Kext -
FF67 Manual bank statement transactions not updated in G/L accounts.
Dear All,
The user has posted the Manual bank statement in the FF67 and saved. But the postings are not updated in the G/L accounts but in FF67 the bank statement is showing that "posting completed". When I check that The Job name has finished successfully in sm37. but when I check in SM35 the batch session also has been created with the same user ID. But it has not processed.
When i ask the user he is saying that they don't process the Batch input session. They just save the FF67 T.code. after some thime the job will complete and post to the G/L accounts.
Please could any body let me know what could be the problem.
When we enter the FF67 the system will ask the start variant and the processing type. There are 4 options in the processing type. could any body explain me about the 4 options.
Regards,
Mr.Rao.Dear All,
Here the user has selected the processing type is 2. That's why the system is created the batch input secssions. so the G/L accounts will be hitted after the batch input secssion are processed.
Regards,
Mr.Rao. -
My iphone battery is not working properly as compare to earlier after IOS 7 update.
Should i change my battery if yes then how much it will cost in india??Turning off things in settings, restoring as new phone, etc. everything I've seen on forums and CNet etc sites
-
ITunes Not Updating iPod When It States That It Has
I purchased songs from the iTunes store. I have automated update. Windows and iTunes recognize my iPod. I get the message that my iPod is updated after I plug it in but it's not updated. I can't get my iPod to update even though the message states that it is updating. What am I doing wrong?
Something might get the wrong idea<<</div>
I'll have to respectfully disagree with you on that, Jim.
I've always found sushi to be remarkably tolerant, even when in a Mexican pasture. It's the French seaside you should be wary of. Especially when riding the dual stage Toro.
-DH
Maybe you are looking for
-
Can you get FCPX on three screens?
Hello, I have a Mac Pro but it is not the late 2013 model. Is there a way to get fcpx on three screens and not just two like on the new mac pro? Thanks.
-
Hello, ClusterWare 11.2.0.3 + RAC db same version . I need to rename one of the ASM instances How can this be done ? the situation is as follows , I needed to take one of the server out of the cluster and then bring him back in . when I have added hi
-
I am currently using Google Earth 4.2.0205.5730 (latest version) with Leopard 10.5.1. For the most part it works great, but I am having one issue that I'm hoping someone out there might know how to fix. Every time I start Google Earth for the first t
-
Hi guys, i am trying to access to RSA7 in SAP ECC 6.0, and i am always getting the same Dump Runtime Errors DBIF_REPO_SQL_ERROR If i go to Abap Editor the dump's instruction is as follow select mandt qname dest from trfcqout up to 1 rows
-
E Recruiting-Display current holding position for the Internal Candidates
Hi Is it possible to display current holding position for the Internal Candidates? Thanks inadvance.