Bouts of packet loss and complete loss of connection
Ok forum, I give up! I need your help.
I have an E1200 and am time out and packet loss issues. The internet connection is fine for 30 seconds to five minuets and then everything times out for 15-20 seconds. Although it’s only a minor incontinence to web browsing, it makes playing games and watching videos a nightmare. “Lost connection to server error.” and the like…
This is what I have done to remedy the problem.
I upgraded to a new router, the e1200 I am currently using, from my Tenda 10/100 N. The problems where the same that I am experience currently and the reason I bought it in the firs place.
When I directly connect to the cable modem, I have no issues and everything is fine.
I have run a trace route and the second hop, (the router to the modem) is the choke point.
I have cloned the MAC address
I have updated the firmware and hard reset
I have throttled my MTU to automatic, 1500, and 1472. None making any difference.
I have disabled NAT and all that does is kill my internet connection
I have disabled all firewalls router and windows, no change.
I replaced the physical wire from the router to the modem.
I have disconnected all devices except one computer, and no difference.
I ran a DNS trace and I have… non routable local internet address 192.168.1.1
DNS-cac-lb-01.rr.com and DNS-cac-lb-02.rr.com
I am using windows 7 and my ISP is time Warner so-cal. Help me obiwan, you’re my only hope.
Sorry friend. I have not had the gaul to load the 1.0 firmware. I am 99% sure I have the 2.0 hardware. I did however unplug my modem for an hour and then try and reconnect. The result was a lossless environment for fifteen to twenty minuets (a long time for me.). But, I am right back still having the same problem. A friend gave me a new netgear router, I am going to try that and I am going to go to Timewarner and have them replace my modem just to make sure there is nothing wrong with the surfboard. I will report back with my findings.
Similar Messages
-
Packet loss and eventual shutdown of port 80 on RV180
I have been using my RV180 router for about a year now. I have had very little issues with it overall. I have seperate wireless access points connected and use those for my wireless devices.
Recently, I started getting very odd connection problems it started as packet loss and then turned into connection loss. The odd part is that it only effects port 80 or the secured port, 880, if I remember correctly. Thats right, everything else on the network works fine. However, I can not access the internet or the RV180 router via it's ip address to check the status. VOIP, other lan networking, gaming, and bitcoin mining is completely uneffected. Direct connection to the modem works without any problems.
I have tried updating the router firmware but no help.
Each time I have this issue the problem is cured simply by unplugging the router and plugging it back in. Nothing else works because I can not log into the router. This problem comes along once a week or so. I have also tried enabling the logs but I get absolutly nothing when I reset the router and log back in. I have had similar problems with routers in the past becoming "bent" after about a year of use and requiring a replacement. I sort of thought that this wouldnt be the case with the Cisco because it is a good brand and came with a five year warranty. I have also scanned every PC on the network for viruses and malware but nothing was located. The remainder of the devices are IP cameras and such.
Can anyone think of anything that could be causing this?So I was able to get the logs tonight by repeatedly pinging the router and it would start letting me get traffic in again.
Wed Dec 4 20:03:02 2013(GMT-0500) [rv180][Kernel][KERNEL] [81097.390000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:02 2013(GMT-0500) [rv180][Kernel][KERNEL] [81097.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:02 2013(GMT-0500) [rv180][Kernel][KERNEL] [81097.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:02 2013(GMT-0500) [rv180][Kernel][KERNEL] [81097.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81101.770000] __ratelimit: 111 callbacks suppressed
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81101.770000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81101.890000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81101.890000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81101.930000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81101.930000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81102.030000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81102.070000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81102.230000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81102.320000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:07 2013(GMT-0500) [rv180][Kernel][KERNEL] [81102.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.020000] __ratelimit: 102 callbacks suppressed
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.020000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.020000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.270000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.320000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.420000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.430000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.520000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:12 2013(GMT-0500) [rv180][Kernel][KERNEL] [81107.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.120000] __ratelimit: 100 callbacks suppressed
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.120000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.310000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.310000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.320000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.500000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:17 2013(GMT-0500) [rv180][Kernel][KERNEL] [81112.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] __ratelimit: 107 callbacks suppressed
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:22 2013(GMT-0500) [rv180][Kernel][KERNEL] [81117.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] __ratelimit: 93 callbacks suppressed
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:27 2013(GMT-0500) [rv180][Kernel][KERNEL] [81122.550000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.560000] __ratelimit: 101 callbacks suppressed
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.560000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.600000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.690000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.750000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.790000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.830000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.830000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:32 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.840000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:33 2013(GMT-0500) [rv180][Kernel][KERNEL] [81127.840000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.140000] __ratelimit: 110 callbacks suppressed
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.140000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.140000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.260000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.300000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.560000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.560000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.560000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.560000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.560000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:38 2013(GMT-0500) [rv180][Kernel][KERNEL] [81133.560000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.290000] __ratelimit: 84 callbacks suppressed
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.290000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:43 2013(GMT-0500) [rv180][Kernel][KERNEL] [81138.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81143.710000] __ratelimit: 126 callbacks suppressed
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81143.710000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:49 2013(GMT-0500) [rv180][Kernel][KERNEL] [81144.570000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81149.580000] __ratelimit: 67 callbacks suppressed
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81149.580000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81149.720000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81149.740000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81150.280000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81150.330000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81150.440000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81150.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81150.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81150.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:54 2013(GMT-0500) [rv180][Kernel][KERNEL] [81150.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:59 2013(GMT-0500) [rv180][Kernel][KERNEL] [81154.870000] __ratelimit: 85 callbacks suppressed
Wed Dec 4 20:03:59 2013(GMT-0500) [rv180][Kernel][KERNEL] [81154.870000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:59 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.030000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:00 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.030000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:00 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.210000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:00 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.210000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:00 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.210000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:00 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.210000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:00 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.210000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:00 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.280000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:00 2013(GMT-0500) [rv180][Kernel][KERNEL] [81155.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.100000] __ratelimit: 114 callbacks suppressed
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.100000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.100000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.270000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.330000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.340000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.350000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.350000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:04:05 2013(GMT-0500) [rv180][Kernel][KERNEL] [81160.540000] nf_conntrack: table full, dropping packet.
Wed Dec 4 20:03:02 2013(GMT-0500) [rv180][Kernel][KERNEL] [81097.390000] nf_conntrack: table full, dropping packet.
Sat Jan 01 00:00:13 2011 (GMT +0000): [RV180] [IKE] INFO: IKE started -
Tons of packet loss and Verizon techs say its fine
As you can see from the below test ran from dslreports.com, I'm having a lot of packet loss issues. This has been going on for nearly two weeks now and tech support has been more of an annoyance than a help upto this point. I've talked to tech support at least 5 times only to be told my line test comes back fine, its normal, reset your modem, delete your cookies, is your pc old, etc. I've even had them vpn itno my system and run pings and they see the packet loss and all the issues I'm having first hand and still say it isn't a big deal. On more than one occasion I've had my modem data light just flashing and had to reset the modem and they suggest I just buy a new modem. Seriously, is this how bad tech support has gotten?
I've shown them test after test after test and the all come back pretty much the same... The thing is its been perfect for years and suddenly this and its like tech support wants to sweep it under the rug or something. I've had it suggested to me the packet loss and high pings when I'm not getting the packet loss is due to my pool being over populated. Like I'm ow getting ping averages of 250-300 instead of 30-40s, again when its not all timing out.
I've posted over on the dslreports forums asking about this as well as in the Verizon specific forums to the techs all with 0 replies from anything and was told to come here and see if anyone would be able to help.
I really not bother with the hassle of switching isps as ive been a loyal Verizon dsl customer for well over 5 years but at this point just knowing how bad tech support is alone might make me want to.
Can anyone offer any insight on what else to do or help on this possibly?
Thanks.
Test Loss Min
Latency Avg
Latency Max
Latency Pass
Fail Simple ping loss check
10secs of 40byte packets 2 per second 5% loss 137ms 141ms 148ms
warn low bandwidth stream
10secs of 56k/bit ping stream 512byte packets 6% loss 142ms 147ms 154ms
warn medium bandwidth stream
10secs of 128k/bit ping stream 512byte packets 2% loss 140ms 147ms 173ms
pass your first hop ping
stream of 40byte pings to 130.81.44.101 4% loss 118ms You are 19ms
to your first hop
pass Ping plot:
Ping plot:
From East Coast - USA to YOU Hop Host LOSS Rcv Sent Best Avg Worst 0 ae-2.bb-b.slr.lxa.us.oneandone.net 0% 60 60 0.46 2.29 59.98 1 te-2-1.bb-b.ms.mkc.us.oneandone.net 0% 60 60 0.92 1.89 36.10 2 64.209.105.233 0% 60 60 13.97 41.38 948.69 3 0.xe-8-2-0.BR3.CHI13.ALTER.NET 0% 60 60 26.13 30.80 80.28 4 0.ae3.CHI01-BB-RTR1.verizon-gni.NET 0% 60 60 26.49 27.84 88.62 5 P15-3.RONKVA-LCR-01.verizon-gni.net 0% 60 60 54.25 55.01 56.32 6 P0-0.RONKVA-RONKVALK-ERXG02.verizon-gni.net 0% 60 60 116.80 121.05 130.35 7 pool-71-171-24-94.nwrknj.east.verizon.net 14% 52 60 142.49 147.61 169.10 (fail) From West Coast - USA to YOU Hop Host LOSS Rcv Sent Best Avg Worst 0 unknown.Level3.net 2% 59 60 0.64 16.67 150.86 1 ae-4-99.edge1.SanJose3.Level3.net 4% 58 60 1.15 5.12 59.35 2 4.68.63.146 0% 60 60 1.25 3.31 55.27 3 0.ae3.XL3.SJC7.ALTER.NET 0% 60 60 1.25 1.68 9.80 4 0.ge-6-3-0.XT1.DCA6.ALTER.NET 0% 60 60 75.58 77.85 108.89 5 0.so-4-0-0.RES-BB-RTR1.verizon-gni.net 0% 60 60 75.52 80.78 136.25 6 P15-3.RONKVA-LCR-01.verizon-gni.net 0% 60 60 90.25 91.97 94.08 7 P0-0.RONKVA-RONKVALK-ERXG02.verizon-gni.net 2% 59 60 154.03 159.68 164.42 8 pool-71-171-24-94.nwrknj.east.verizon.net 4% 58 60 175.74 183.27 187.00 (fail)As you can see from the below test ran from dslreports.com, I'm having a lot of packet loss issues. This has been going on for nearly two weeks now and tech support has been more of an annoyance than a help upto this point. I've talked to tech support at least 5 times only to be told my line test comes back fine, its normal, reset your modem, delete your cookies, is your pc old, etc. I've even had them vpn itno my system and run pings and they see the packet loss and all the issues I'm having first hand and still say it isn't a big deal. On more than one occasion I've had my modem data light just flashing and had to reset the modem and they suggest I just buy a new modem. Seriously, is this how bad tech support has gotten?
I've shown them test after test after test and the all come back pretty much the same... The thing is its been perfect for years and suddenly this and its like tech support wants to sweep it under the rug or something. I've had it suggested to me the packet loss and high pings when I'm not getting the packet loss is due to my pool being over populated. Like I'm ow getting ping averages of 250-300 instead of 30-40s, again when its not all timing out.
I've posted over on the dslreports forums asking about this as well as in the Verizon specific forums to the techs all with 0 replies from anything and was told to come here and see if anyone would be able to help.
I really not bother with the hassle of switching isps as ive been a loyal Verizon dsl customer for well over 5 years but at this point just knowing how bad tech support is alone might make me want to.
Can anyone offer any insight on what else to do or help on this possibly?
Thanks.
Test Loss Min
Latency Avg
Latency Max
Latency Pass
Fail Simple ping loss check
10secs of 40byte packets 2 per second 5% loss 137ms 141ms 148ms
warn low bandwidth stream
10secs of 56k/bit ping stream 512byte packets 6% loss 142ms 147ms 154ms
warn medium bandwidth stream
10secs of 128k/bit ping stream 512byte packets 2% loss 140ms 147ms 173ms
pass your first hop ping
stream of 40byte pings to 130.81.44.101 4% loss 118ms You are 19ms
to your first hop
pass Ping plot:
Ping plot:
From East Coast - USA to YOU Hop Host LOSS Rcv Sent Best Avg Worst 0 ae-2.bb-b.slr.lxa.us.oneandone.net 0% 60 60 0.46 2.29 59.98 1 te-2-1.bb-b.ms.mkc.us.oneandone.net 0% 60 60 0.92 1.89 36.10 2 64.209.105.233 0% 60 60 13.97 41.38 948.69 3 0.xe-8-2-0.BR3.CHI13.ALTER.NET 0% 60 60 26.13 30.80 80.28 4 0.ae3.CHI01-BB-RTR1.verizon-gni.NET 0% 60 60 26.49 27.84 88.62 5 P15-3.RONKVA-LCR-01.verizon-gni.net 0% 60 60 54.25 55.01 56.32 6 P0-0.RONKVA-RONKVALK-ERXG02.verizon-gni.net 0% 60 60 116.80 121.05 130.35 7 pool-71-171-24-94.nwrknj.east.verizon.net 14% 52 60 142.49 147.61 169.10 (fail) From West Coast - USA to YOU Hop Host LOSS Rcv Sent Best Avg Worst 0 unknown.Level3.net 2% 59 60 0.64 16.67 150.86 1 ae-4-99.edge1.SanJose3.Level3.net 4% 58 60 1.15 5.12 59.35 2 4.68.63.146 0% 60 60 1.25 3.31 55.27 3 0.ae3.XL3.SJC7.ALTER.NET 0% 60 60 1.25 1.68 9.80 4 0.ge-6-3-0.XT1.DCA6.ALTER.NET 0% 60 60 75.58 77.85 108.89 5 0.so-4-0-0.RES-BB-RTR1.verizon-gni.net 0% 60 60 75.52 80.78 136.25 6 P15-3.RONKVA-LCR-01.verizon-gni.net 0% 60 60 90.25 91.97 94.08 7 P0-0.RONKVA-RONKVALK-ERXG02.verizon-gni.net 2% 59 60 154.03 159.68 164.42 8 pool-71-171-24-94.nwrknj.east.verizon.net 4% 58 60 175.74 183.27 187.00 (fail) -
Tool like PathPing that can pinpoint packet loss and can be configured to run for 24 hours
Does anybody know if there is a simple tool like PathPing that can pinpoint packet loss and can be configured to run for eg. 24 hours. I need it for windows XP preferable a cmd line tool like PathPing. Thanks Simon.
Thanks for your answer. I already downloaded winmtr.
Regards
Simon
From:
namohamm
To:
Simon Vyrdal/Sweden/Contr/IBM@IBMSE
Date:
2010-12-30 08:29
Subject:
New message: "Tool like PathPing that can pinpoint
packet loss and can be configured to run for 24 hours"
simonvyrdal,
A new message was posted in the Discussion thread "Tool like PathPing that
can pinpoint packet loss and can be configured to run for 24 hours":
https://supportforums.cisco.com/message/3258861#3258861
Author : Nael Mohammad
Profile : https://supportforums.cisco.com/people/namohamm
Message: -
100% packet loss and I can't play Online games
Recently I just got cable installed and the Internet works and it connects to my Xbox one but I have 100% packet loss and I can't play any online games or apps on my phone. Can someone please help me out as I have waited about 2 weeks to get it working!
hi AireVuqe101
I'm referring your post to our Social Media Tech Team for some further assistance.
You may not receive any contact from them until Monday, so if you need further assistance in the meanwhile, we do have a 24 hour Technical Support team who can be contacted by either calling 133933 or via Live Chat http://tel.st/gq6m
Regards -
E4200 - terrible G-only speed, packet loss and throughput variation
Got this router today, was disappointed to see it fail simple performance tests using wireless G on out-of-the-box firmware 1.0.0.1 and after upgrading to 1.0.0.2.
I tried mixed/G/G+B modes, optimal positioning of the router, manual channels 1,5,6,11 and auto channel, security disabled and 5Ghz disabled, rebooting and power cycling - no difference. I also went on to try a total of 3 different laptops again with no difference (they have Atheros, Realtek and Intel chipsets, all 802.11g, no 802.11n)
Uplink and downlink speeds from WLAN to LAN are consistenly poor (tested using Jperf and Qcheck), with uplink to the router being consistently worse. For example, at my favoured location a few metres from the router with very good signal strength, an Orange Livebox 1.2 (or 'Livebox Mini', which is a standard ISP provided router here in the UK) gives rock solid 22Mbps up and down, a humble Sagem 2504N gives rock solid 21Mbps up and down, the E4200 gives about 11Mbps up and 13Mbps down, even though signal strength at this location as reported by Inssider is in fact highest from the E4200. Wherever I try it, like for like, the E4200 throughput underperforms massively for any wireless router let alone a top-of-the-range model. Even right next to the router, I only seem to get an average of about 18Mbps down, not the full 22Mbps I would expect from 802.11g.
I also see great throughput variation on these tests. So, I ran ping tests from the cmd line (from wireless to a wired computer on the E4200), and sure enough there is packet loss. There is no packet loss on any of my other routers. I also put the E4200 into bridge mode and used it as a wireless access point to another router, again there was packet loss and throughput variation. Coming here to post, I saw some other threads about packet loss, I can confirm I am another user seeing the same thing.
Comments/comparisons/ideas for fixes welcome, but I'm sorry to say, this router is obviously going back.Thanks, but Cisco Connect did not help.
I am using this router as a wireless access point, without connecting a modem to the WAN port. Cisco Connect did not like this one bit and would not proceed because it could not detect an Internet Connection. It then tried to send a report of why installation had failed over the internet
Not that I should have to use Cisco Connect to avoid packet loss and extremely poor speeds anyway! Nothing I have seen in the Linksys documentation or during setup suggests it will alter performance so I don't know how it would help anyway (the router page only warned that configuring manually meant my network could be left unsecured).
I don't know what the speed tests are through Cisco Connect, because I cannot install it and I can't find a user guide to the software, not even on the installation disc. I don't see how these speed tests will change anything though, how can they give meaningful, different results of a simple TCP throughput test, as I performed using Jperf/Iperf and IxChariot. -
Airport Extreme N - Optonline - packet loss and resets
Setup:
I have been having the below issue since moving to an area in New Jersey with Optonline (CableVision) cable internet access. The cable modem is a WebStar with connection to a Airport Extreme "N" via ethernet to WAN port on Airport Extreme N.
The issue was not present when I was with Comcast using an Airport Extreme G, it began when using Optline with the Airport Extreme G and continues with the Airport Extreme N. Airport is configured to b/g/n compatible, DHCP, WPA/WPA2 security, various channels used, no interference noted in the wireless spectrum using several software tools.
Issue:
Webpage load speeds are very slow until the Airport Extreme base is restarted, Optonline has confimed a strong signal to the cable modem and when I plug directly into my iBook/iMac from the modem using ethernet they test for packet loss and it is 0-2%. I have confirmed that directly plugging in removes the issue.
When plugged into the Airport Extreme (either the G or N version) packet loss has approcahed 90% and the only way to load a page is to continually hit "reload" to get a slow eventual load. Once a restart of the Airport Extreme is done the issue is resolved for hours/days until it begins again, requiring another restart.
Any help would be appreciated!
iMac G5 2.1GHz 20" Mac OS X (10.4.9) iBook G4 1.33 12"
iMac G5 2.1GHz 20" Mac OS X (10.4.9) iBook G4 1.33 12"My n Airport doesn't work well on OOL either. Back to using round AEBS g.
The n router when I click a webpage link, has a delay of 5-10 seconds before Safari goes to the link. Using my g Airport I click a link and Safari instantly loads the page.
If I do an OOL speed test, the n router is a bit slower than the g router, but speed tests fine bottomline. But the delay issue has made it impossible for me to work, so I switched back to my UFO AEBS g Airport.
Whatever the imcompatability with OOL is I hope will be rectified when I see a release of an Apple n Airport update. In the mean time, g for me. -
TC & MBP - complete loss of wireless connection and usage
I apologise in advance if this is a very long winded post! I've been an Apple fan for some 20 years now and it's only in the last three months that my love affair is starting to wane due to (what seems to me) poor hardware releases.
My setup:
1 x PowerBook G4 1.25Ghz with Edimax 802.11n PC Card
1 x MBP 2.4Ghz (purchased April 2008) with AirPort 802.11n
1 x Time Capsule 500Gb
1 x Airport Extreme Base Station Gigabit Ethernet edition
1 x Netgear DG384 v2 (wired only) modem router
1 x standard ADSL connection (8Mbps) from a UK ISP (and yes, 8Mb is about the norm for the UK! Though in reality, it means closer to 4Mb...)
The Netgear router is connected to the ADSL line and is set up as the DHCP server for the network. I have a Fixed IP address from my ISP. The Time Capsule is connected via ethernet to the Netgear router. The TC is set up in Bridge mode as the router serves DHCP. The TC is wall mounted via the excellent AirMount from H-Squared.
The TC has been through a myriad of configurations in an attempt to create a stable wireless environment since its purchase in April. Prior to my recent holiday (two weeks in Greece - hurrah!), the current configuration was solid for both Macs.
The config is: Bridge mode; 2.4Ghz N Only wireless; WPA2 secured; no MAC address access control restrictions (so pretty straightforward). The TC is running firmware 7.3.1. It is setup as "Create a Wireless Network"
Both Macs are running OS X 10.5.3 with all of the latest updates including AirPort Utility 5.3.2.
It took me about six weeks to hit upon this config for the TC having had many wireless drop outs, stalled connections, lost internet connections (ie. I could access the TC HDD but could not access the internet using the same wireless connection). So much frustration in the early days - I tried many of the solutions on this forum but to no avail until I hit upon the 2.4Ghz N Only route which seemed to be the answer to all my problems.
Prior to leaving on holiday, I unplugged all of the equipment in the room including the TC and the router. When I returned, I restarted everything in a logical sequence - router first (and waited for a connection), then the TC and then the Macs.
From this point on the problems have started. The PB G4 with the wireless card has a more or less stable connection. The wireless card connects immediately to the TC but then it takes approximately 30-60 seconds for an internet connection to work (so I see a lot of the Not connected to the internet messages in Safari). It seems to immediately get an IP address from the router via the TC but then the internet connection itself takes a while to come up.
The MPB on the other hand is a nightmare. Since returning from holiday I have not been able to get a workable wireless connection at all. In no particular order, the problems that the MBP exhibits are as follows (these can occur at the same time or individually):
i) only returns a self-assigned IP address; renewing the DHCP lease does not fix the problem
ii) does not see the network at all (although it will see others in the vicinity)
iii) cannot connect to the network - returns the Connection Timeout error or very occasionally the Password Incorrect error; I have tried connecting the network via the AirPort menu bar item, via Join another network... from the menu bar, via the Network selection menu in System Preferences > Network and even via Internet Connect - all with no success
iv) sometimes I am able to connect to the network but no IP address is received. Having checked the TC logs, it shows the same error occurring over and over again:
Jun 26 22:06:04 Severity:5 Associated with station 00:1e:c2:ba:78:6c
Jun 26 22:06:07 Severity:5 Deauthenticating with station 00:1e:c2:ba:78:6c (reserved 2).
Jun 26 22:06:07 Severity:5 Disassociated with station 00:1e:c2:ba:78:6c
The MBP connects but is immediately thrown off the network.
So to all intents and purposes, the wireless aspect of the MBP and the TC are completely useless.
When I use a wired (ethernet) connection to the TC everything is joyful. Instant IP address assignment, excellent connection speeds, no drop outs and so on. So as far as I can ascertain, the TC is working fine with the exception of the wireless/wireless security.
The AEBSn that is connected to the same network no longer appears in Airport Utility.
Having read through many posts here, I have tried many solutions including:
- downgrading the FW to 7.3; no difference at all
- turning off wireless security; no difference at all
- changing channels; I've tried 1, 6, 9, 11 and 13 with no difference at all
- changing the wireless mode; B/G, G only, N only all make no difference (I can't use 5Ghz N only as the PB G4 does not support this and I need both Macs wirelessly connected)
- rebooting the TC (both via Airport Utility and 'power off'); makes no difference
- reinstalled OS X 10.5.1 (via the install disks that came with the MBP) using the Archive & Install feature; then used the Combo updater to upgrade directly to 10.5.3; once again, no difference.
I have not yet done a hard reset as this has made no difference in the past but obviously I will try it.
In other words, HELP!
I am stymied. I have tried so many solutions offered on here and on the likes of MacFixIt and other Mac forums none of which have brought back my wireless connection for the MBP.
The MBP works very well with other wireless connection. For example, at work, we have a Linksys WRT54G wireless router connected to a BT leased line. I have not had a single connection issue for three months with this setup. Similarly, whilst on holiday, I used many different hot spots and had no issues with the wireless connection. All of this evidence leads me to suspect that the MBP is not the issue.
From what I can tell, the problem seems to be in the wireless security on the TC. It seems to prevent access by MBP (though not the PB G4 using a wireless card) but disabling security did not change the error messages shown in the log or the lack of connectivity.
It is a real shame that I cannot get a satisfactory working environment with the TC as the concept is great. The reality is, however, that it is unusable in its current condition and loathe as I am to try and return it or replace it, I am rapidly coming the conclusion I will have to.
Before I do, however, I am hoping that the genii who exist on these forums may be able to proffer some ideas or solutions that I haven't yet tried.
My sincere thanks will go to anyone who provides a solution for me. There may even be beer involved as a mark of gratitude!!
Thanks for reading and fingers crossed someone knows something special...Smokerz: thanks for the reply and the advice. Not really in a position to set up a dual network at the moment due to the positioning of the TC and the AEBS but if I get an opportunity to try it I will.
I have temporarily given up with the TC as the router for the wireless network. I've installed a Vigor 2820n modem router (it's the only one I could find that has a Gigabit port - only one though) as well being a modem (ADSL) router. Thus far, everything seems fine - although I have had a couple of drop outs due (I think) the AirPort connection on the MBP. And interestingly, I've set up the TC as a "test" wireless network using the Vigor's internet connection and it's way more stable than with the Netgear router. So perhaps it's a combination of many factors - the poor Netgear router, the TC and the MBP AirPort connection - that was causing the issues.
I'll give 10.5.4 a go as well and see if that helps at all.
Thanks to all who read the question - if anyone else has thoughts I'd be delighted to hear them. -
I'm using Windows 7. Recently installed 11 and seemed to have lost all my audiobooks and hated the new format. So, I decided to revert back to an older version. I unistalled itunes and reinstalled 10.7 but then all my books were gone. I called carbonite and they restored my books. Two days later, I was unable to restore them back given the instructions from carbonite. After a bit of effort I found I needed to "unhide" each and every book under "add folder to library" in the file menu. It seems to be working, but my books are not set up the way they the used to be. I used to have a nice three column block under my menu. It contained, "Spoken or audio" in the first column, Author/Artist in the second, and in the third each book the author wrote was listed. I could choose one book, put it into my play list and then to my ipod. Try as I might I can no longer sort like this and at a complete loss what to do. Right prior to downloading 11 everything was fine and grouped just the way I liked it. If anyone has any ideas, I would be grateful. I've tried the sorting by artist and that doesn't set it the way it used to be. Thank you in advance.
Hi someotherguy,
Can you help me with this problem?
I hit enter to stop the normal boot and then appear a window to select different options:
- F1: Enter BIOS
- Another one I don't remember
- F12: Select bootable device
Any of the menus I've tryied to enter I got a message afterwards saying:
"Intel Boot Agent GE v1.3.81
PXE 2.1 Build 091 WfM 2.0)"
And just stays there. Nothing happens.
After pressing F1 or F12 or other, I got a small message saying press CTRL+S to enter the setup menu. If I press it, I enter in a menu just to change the amount of time that message appear and if I want it or not.
Can you help me?
I need to activate the virtualization on the BIOS in order to setup virtual machines! -
Hello Comunity,
I'm at a complete loss and I hope you could help me.
The machine I have is I believe an early 2006 iMac model. (Model identifier 4,1 if I recall correctly).
Awhile ago I installed Snow Leopard on the machine but have since begun encountering serious problems (but I think it's due to the hardware and it's age rather than the software, Snow Leo was running smoothly) and now the computer won't start - I'm faced with a grey screen and a flashing folder with a question mark on it. I tried booting using the various key combinations and as I understood it, my last resort at fixing it myself would be using Disk Utility on the installation DVD.
This is what happens:
I boot the computer, insert the disk, press down and hold C (also tried Option). I hear the computer trying to read the disk, but after a considerable aount of time holding down the key and a grey screen, the disk ejects and the flashing folder returns.
Could anyone offer an insight or advice?
At this point I'm not even that interested in fixing the machine, but there are some extremely valuable files that I need to recover (the machine gave out just days before I got my extrenal HDD to back them up).
I'm worried about taking the machine down to the Genius Bar - I'm a completely self-supporting student and I imagine the recovery cost would be huge (if anyone could provide any information on the potential cost of the repair and/or recovery that would help).One thing to try without needing the install disk: reboot holding down cmd-S. It should reboot to a black screen and text prompt. Type the following, with spacing exactly as shown, hit the return key after each line:
mount -uw /
fsck -fy
Then type
reboot
and see if that helps.
Do you have any other Macs in the household (or cna use a friend's) that you can try connecting to it with a Firewire cable? If so, reboot the iMac holding down T, you should see a large Firewire symbol moving across the screen. Connecting to another Mac with a FW cable will show you the iMac's hard drive mounted to the other Mac's desktop.
You can also try Diskwarrior, which fixes drive filestructure problems. It's around $100.
Professional data recovery cost would depend on a) whether the hard drive is actually at fault, b) if it's physically damaged or just has a filestructure problem. A physically damaged drive can go into the thousands of dollars for data recovery; a drive with filestructure issues usually costs a lot less to recover files.
Matt -
Color Banding and Color Loss during playback
I'm experiencing weird behavior with Premiere Pro CS6.
As you can see in the above images I'm experiencing banding whenever Full resolution is selected for either playback or paused. If 1/2 or lower is selected then the image looks fine (albeit not full resolution). The images are 1/2 resolution in the Source monitor and Full resolution in the Program monitor. The left image shows the same thick banding as in the right image, with the addition of thinner stripes within the thick bands (don't know if they can be seen at this resolution or not).
This behavior is also not consistent. Some clips don't experience this at all. The clips in this example are MXF MPEG2 clips shot on a Canon XF300 however the same has been seen on everything from AVI to MOV and yet not *every* AVI or MOV.
Another oddity that I'm seeing is that when I use the fullscreen command to make the Full Resolution monitor fullscreen, the image inverts itself (upside down and backwards) and becomes black and white (I couldn't get a screengrab of it though).
My initial thought was that it would be a graphic driver error, but I've uninstalled and reinstalled the driver to no effect. I've also tried reinstalling PPro CS6 with the same results. I'm also tried merely cleaning the cache/preferences... also the same result. I'm at a complete loss and was hoping that someone out there had a solution I haven't thought of yet. My colleagues are not experiencing this issue, despite being on the exact same machines (specs below) with the same updated build of CS6.
Alienware M17X R2
Intel i7 2.13GHz
8GB Ram
Windows 7 - 64-bit
SLI - ATI Mobility Radeon HD 5800 (1GB each) - Driver version 8.982; Catalyst Version 12.8Jeff! You're amazing! That was exactly the problem. Thank you also Jim for offering your input. Thank you for solving this aggravating problem. It's been bugging me for weeks!
-
T500 performance loss and restart issue after low battery shutdown
Hi,
Some days ago I experienced a significant loss in performance of my T500. Unfortunately it seems to be a continuous loss and the games I play, e.g. empire total war that did run ok before are nearly unplayable at the moment.
Additionally, when the computer shuts down due to low battery, it no longer manages to resume windows but always crashs during reboot (black screen and hard disk symbol is moving, no other activity for 10 minutes)
I am working with the standard vista installation and installed all automatic updates, but also every time when I shutdown the computer, no matter how long it has been running (even after 1 minute and after a rebooting 3 minutes ago), the red shutdown symbol in start shows that an update needs to be installed.
any ideas?
Many thanks in advance !
Message Edited by Walky on 06-18-2009 09:39 PM
Message Edited by Walky on 06-18-2009 09:41 PMWell, the problem, seem's to have reoccured: Battery ran out (even the indicator leds on the side didn't show any life), Time reset to 1.1.2001, again some rebooting and setting the time again...
Is this a sign of a degrading battery health status?
It looks like reseting the SMC didn't help after all. -
Through damage, loss and resetting computers, my iTunes has synced itself to 5 devices (which I believe is the max) but I currently have my 6th iPod touch and need to know how to keep all this music and put it onto this other iPod. Do I create another Apple ID? Is it possible?
You can have 10 devices associated with your iTunes account for iCloud purposes. See:
iTunes Store: Associating a device or computer to your Apple ID
You can have five computers authorized for one iTunes account. See:
iTunes Store: About authorization and deauthorization
Just what are you trying to do and what message do you get? -
SALES Analysis and profit loss statment
Hi All ,
Dear Experts,
My Sales Analysis and profit loss statement Value is deferent . i want to know that which entry show in sales analysis and which entry show in profit loss statment .
Thanks & Regard
AREEBA ALIAree,
Both report are different. The sales analysis will use document of sales orders, delivery order, invoice and credit memo.
The P&L use journal entry of invoice and credit memo. Can you be more specific about the different ?
JimM -
Can we take Balance sheet and profit & Loss account as per plant & Sales
Hi Team,
Can we take Balance sheet and profit & Loss account as per plant wise & sales office wise also.
Regards
JKMhi jkm
Hi
This can solve your issue could be helpful to you.
Go to this menu path for report painter
Accounting - Financial Accounting -Special Purpose Ledger - Tools - Report Painter - Report Writer - Report Group - Display
T code GR53, GR55
Enter the report group you want for b/s and p/l statement and choose execute and give the report group again and choose execute.
After that give the year, period from to, company code, fiscal year, ledger and plan version 01 and choose execute
Choose in front of the item Production Variances. The system displays the account to which the line items were posted. Material consumption is posted to account OEM Products Consumed.
To call up detailed data, double-click on account
In the dialog box, choose Actual Line Items for Table GLFUNCT, and then choose
To display the original document, simply double-click on it to call up the detailed data. In this case, the original document is a Materials Management document.
You document is listed under the FI-SL document number that you noted in the step Display Goods Issue Document. Select the Doc. info tab and simulate .
Select one of the items relevant for material consumption by double-clicking it. This should be item 002, 004, or 006.
Choose enter go back and cost of sales appear now switch to your first session.
kind regards
Arman
sap fico
Maybe you are looking for
-
When I try and launch Premiere Pro CS6 I get dynamiclinkmanager quit unexpectedly
And Premiere Pro CC never launches. And the dynamiclinkmanager window keeps coming up, to the point that i can't do anything else as the window just keeps going to the foreground. CS6 all works perfectly fine. I am on a MacPro 4,1 running 10.8.4 with
-
Update was terminated error while scheduling maintenance plan
HI Friends, I created a maintenance plan.I scheduled the order and i saved. Now when i tried to see the schedule i am getting a message "Update was terminated" the detailed error is Update was terminated System ID.... DEV Client....... XXX User..
-
Oracle Database Console Service not starting on Windows 2008 R2
I am installing Oracle 11G The database installs fine, however Database Console service will not start. The java process is launched and I get the login screen, however after logging in I see: Error: Internal Error has occurred. Check the log file fo
-
InDesign docs won't print on Epson CX 6600
Interesting problem. Computer is a "basketball" iMac 17" LCD G4 with OSX 10.3.9. Tried to print to an Epson CX6600 multifunction printer/scanner/copier, after the CX5200 died. Sending the 6600 any doc done in InDesign stalls to "Jobs Stopped" after s
-
Hi, i´m using a full screen widget to show various images of my portfolio, but that widget cuts my images at bottom: Original Image: In Full Screen widget: Settings of the widget: It´s a bug? someone with the same issue? there are solution? Thanks!