Burning errors from slower ATA bus?
I've been digitizing old videotapes and have gotten into a comfortable routine. The process is iMovie to iDVD to .img file to .cdr file to disk. After burning I store the .cdr files on my #3 hard drive.
The other day I tried burning a DVD from the .cdr file on that #3 hard drive, which is on the slower ATA 66 bus, and encountered repeated failures during the verification phase.
Burning the same file from the regular HD on the ATA 100 bus was successful.
Is it possible that the slower bus speed is the culprit? In the past that HD has given me some other problems, but the files copy from HD to HD just fine.
alphaniner wrote:Don't worry about the Radeon error for now. The other errors related to your drive bus are probably the problem. Normally I'd recommend checking cables and connections. But I've never seen a "SError:" line with so many 'details' and you have such errors on two ports, so it may be more complicated than that. Have you searched for info on Linux support of the controller?
Thanks for the response.
I searched for the things you wrote. By "drive bus" and "controller" do you mean the bus driver and device controller from this diagram?
http://www.linuxforu.com/wp-content/upl … 1/ldd1.jpg
Additionally, I found the following forum post while searching: http://ubuntuforums.org/showthread.php?t=2038227
Does that mean I should try reconnecting my drives to different ports on my motherboard?
Last edited by Commie Pinko (2013-12-17 22:39:41)
Similar Messages
-
[SOLVED] Trying to install from CD, ATA bus errors
I've been running Arch on what used to be my main computer for over a year now, and I recently built a new box. I already have Windows 8.1 installed on it. However, when I try to boot up the Arch install disk to set up a dual boot, I get the following errors:
:: Triggering uevents...
[ 1.764769] radeon 0000:01:00.0: Invalid ROM contents
[ 33.375619] ata8.00: exception Emask 0x52 SAct 0x0 SErr 0xffffffff action 0xe frozen
[ 33.375642] ata8: SError: { RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIS DevExch }
[ 33.375682] ata8.00: failed command: IDENTIFY PACKET DEVICE
[ 33.375698] ata8.00: cmd a1/00:01:00:00:00/00:00:00:00:00/00 tag 0 pio 512 in
[ 33.375698] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x56 (ATA bus error)
[ 33.375736] ata8.00: status: { DRDY }
[ 33.525620] ata7.00: exception Emask 0x52 SAct 0x1 SErr 0xffffffff action 0xe frozen
[ 33.525645] ata7: SError: { RecovData RecovComm UnrecovData Persist Proto HostInt PHYRdyChg PHYInt CommWake 10B8B Dispar BadCRC Handshk LinkSeq TrStaTrns UnrecFIS DevExch }
[ 33.525686] ata7.00: failed command: READ FPDMA QUEUED
[ 33.525703] ata7.00: cmd 60/08:00:00:00:02/00:00:00:00:00/40 tag 0 ncq 4096 in
[ 33.525603] res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x56 (ATA bus error)
[ 33.525743] ata7.00: status: { DRDY }
After this, the cursor stops blinking and nothing else happens.
I am using UEFI, however I booted the disk using AHCI as well and got the same error, so I don't believe that its causing the problem.
I downloaded the ISO from the torrent link on the Arch downloads page, checked the "verify contents" box in Windows when I burned the disk, and tried burning the ISO on a different disk.
Any assistance would be greatly appreciated.
Last edited by Commie Pinko (2013-12-19 20:07:08)alphaniner wrote:Don't worry about the Radeon error for now. The other errors related to your drive bus are probably the problem. Normally I'd recommend checking cables and connections. But I've never seen a "SError:" line with so many 'details' and you have such errors on two ports, so it may be more complicated than that. Have you searched for info on Linux support of the controller?
Thanks for the response.
I searched for the things you wrote. By "drive bus" and "controller" do you mean the bus driver and device controller from this diagram?
http://www.linuxforu.com/wp-content/upl … 1/ldd1.jpg
Additionally, I found the following forum post while searching: http://ubuntuforums.org/showthread.php?t=2038227
Does that mean I should try reconnecting my drives to different ports on my motherboard?
Last edited by Commie Pinko (2013-12-17 22:39:41) -
Can't fully boot OS 9 when OS X 10.4 drive is connected to ATA bus
A friend has a g4 733 quicksilver running os 9.2.2. He bought a new 80gb drive and I installed it along with OS X 10.4. Updated and installed various applications (mainly audio apps).
Then tried to boot back into OS 9 and at the very end of the startup progress (when the extensions are loading at the bottom of the screen) I get a message - something like "error 10" or "illegal instruction" or "bus error" (it changes).
I'm able to start OS 9 holding down shift with extensions off, but no combination of checked or unchecked extensions seemed to fix the problem (in fact, un-checking all extensions in extension manager still reproduced the problem; how is that different than booting with shift?).
The only solution I've found is to completely disconnecting the new hard drive with 10.4 from the ATA bus. BTW... When I boot OS 9 with extensions off, I can see the OS X drive. Also, OS X can see the OS 9 drive. And I tried master/slave and CS jumper settings on the hard drives.
Anyone have any ideas or suggestions?
Thanks!!Hi, bcometa -
When a machine is started (in OS 9) with Shift held down, not only are extensions disabled (selectively - there's a couple or so that are intentionally not disabled), but control panels and things in the Startup Items folder in System Folder are prevented from loading.
The problem causer may be a control panel, or it may be something in the Startup Items folder - or both. It would be something that would attempt to interact with an additional drive, and fails in the attempt. Things in this category can include 3rd-party software, such as: a disk utility like Silverlining or Norton; a security app such as virus software; or most anything else designed to scan or check drives for something.
Sometimes resetting PRAM can help, by forcing the Mac to acknowledge and register a change in hardware configuration during startup.
in fact, un-checking all extensions in extension manager still reproduced the problem; how is that different than booting with shift?
In addition to disabling extensions (selectively, as I mentioned earlier; Text Encoding Converter is one that is not disabled, as I recall), booting with Shift held down in OS 9 also:
• prevents the loading of control panels;
• prevents the loading of certain items which are located outside the Extensions folder, loose in the System Folder;
• prevents the loading of items in the Startup Items folder;
• prevents Disk First Aid's intrusive checking of the drive after an 'improper' shutdown. -
Hello,
I have some problems with hard drive on my laptop. Sometimes everything freezes for few seconds (usually during start-up, but sometimes after I login) and I get some errors. After that, everything seems to be working fine.
Part of dmesg with errors:
[ 10.019887] ata1.00: cmd 60/00:10:10:da:59/01:00:0f:00:00/40 tag 2 ncq 131072 in
res 41/84:00:f2:da:59/00:01:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 10.019968] ata1.00: status: { DRDY ERR }
[ 10.019992] ata1.00: error: { ICRC ABRT }
[ 10.020017] ata1: hard resetting link
[ 10.339913] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 10.443163] ata1.00: configured for UDMA/133
[ 10.443191] ata1: EH complete
[ 10.516832] ata1.00: exception Emask 0x0 SAct 0x7000 SErr 0x0 action 0x6
[ 10.516877] ata1.00: irq_stat 0x40000008
[ 10.516902] ata1.00: failed command: READ FPDMA QUEUED
[ 10.516935] ata1.00: cmd 60/e8:60:e8:16:3b/00:00:0f:00:00/40 tag 12 ncq 118784 in
res 41/84:e8:8c:17:3b/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 10.517017] ata1.00: status: { DRDY ERR }
[ 10.517041] ata1.00: error: { ICRC ABRT }
[ 10.517067] ata1: hard resetting link
[ 10.836973] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 10.964972] ata1.00: configured for UDMA/133
[ 10.965002] ata1: EH complete
[ 10.984003] ata1: limiting SATA link speed to 3.0 Gbps
[ 10.984015] ata1.00: exception Emask 0x0 SAct 0x60020000 SErr 0x0 action 0x6
[ 10.984106] ata1.00: irq_stat 0x40000008
[ 10.984157] ata1.00: failed command: READ FPDMA QUEUED
[ 10.984225] ata1.00: cmd 60/20:e8:40:6e:b0/00:00:13:00:00/40 tag 29 ncq 16384 in
res 41/84:20:46:6e:b0/00:00:13:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 10.984397] ata1.00: status: { DRDY ERR }
[ 10.984445] ata1.00: error: { ICRC ABRT }
[ 10.984497] ata1: hard resetting link
[ 11.304016] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 11.409308] ata1.00: configured for UDMA/133
[ 11.409343] ata1: EH complete
[ 11.441025] vboxpci: IOMMU not found (not registered)
[ 11.543239] bbswitch: version 0.8
[ 11.543246] bbswitch: Found integrated VGA device 0000:00:02.0: \_SB_.PCI0.GFX0
[ 11.543252] bbswitch: Found discrete VGA device 0000:03:00.0: \_SB_.PCI0.RP05.PEGP
[ 11.543262] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 11.543355] bbswitch: detected an Optimus _DSM function
[ 11.543372] pci 0000:03:00.0: enabling device (0006 -> 0007)
[ 11.543434] bbswitch: Succesfully loaded. Discrete card 0000:03:00.0 is on
[ 11.545169] bbswitch: disabling discrete graphics
[ 11.545181] ACPI Warning: \_SB_.PCI0.RP05.PEGP._DSM: Argument #4 type mismatch - Found [Buffer], ACPI requires [Package] (20141107/nsarguments-95)
[ 13.327790] r8169 0000:01:00.0 enp1s0: link up
[ 20.651344] ata1.00: exception Emask 0x0 SAct 0x2000000 SErr 0x0 action 0x6
[ 20.651349] ata1.00: irq_stat 0x40000008
[ 20.651353] ata1.00: failed command: READ FPDMA QUEUED
[ 20.651359] ata1.00: cmd 60/08:c8:98:86:ae/00:00:10:00:00/40 tag 25 ncq 4096 in
res 41/84:08:98:86:ae/00:00:10:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 20.651361] ata1.00: status: { DRDY ERR }
[ 20.651363] ata1.00: error: { ICRC ABRT }
[ 20.651367] ata1: hard resetting link
[ 20.971293] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 21.080441] ata1.00: configured for UDMA/133
[ 21.080467] ata1: EH complete
[ 21.121498] ata1.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6
[ 21.121503] ata1.00: irq_stat 0x40000008
[ 21.121507] ata1.00: failed command: READ FPDMA QUEUED
[ 21.121513] ata1.00: cmd 60/00:e8:00:f4:69/01:00:0f:00:00/40 tag 29 ncq 131072 in
res 41/84:00:ee:f4:69/00:01:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 21.121515] ata1.00: status: { DRDY ERR }
[ 21.121517] ata1.00: error: { ICRC ABRT }
[ 21.121521] ata1: hard resetting link
[ 21.441483] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 21.546775] ata1.00: configured for UDMA/133
[ 21.546795] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 21.546798] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 21.546801] sd 0:0:0:0: [sda] ASC=0x47 ASCQ=0x0
[ 21.546802] sd 0:0:0:0: [sda] CDB:
[ 21.546804] cdb[0]=0x28: 28 00 0f 69 f4 00 00 01 00 00
[ 21.546812] blk_update_request: I/O error, dev sda, sector 258601984
[ 21.546829] ata1: EH complete
[ 21.606131] ata1.00: exception Emask 0x0 SAct 0x200 SErr 0x0 action 0x6
[ 21.606139] ata1.00: irq_stat 0x40000008
[ 21.606145] ata1.00: failed command: READ FPDMA QUEUED
[ 21.606155] ata1.00: cmd 60/88:48:00:d8:36/00:00:0f:00:00/40 tag 9 ncq 69632 in
res 41/84:88:04:d8:36/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 21.606160] ata1.00: status: { DRDY ERR }
[ 21.606163] ata1.00: error: { ICRC ABRT }
[ 21.606170] ata1: hard resetting link
[ 21.924963] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320)
[ 22.035385] ata1.00: configured for UDMA/133
[ 22.035408] ata1: EH complete
[ 22.111984] ata1: limiting SATA link speed to 1.5 Gbps
[ 22.111991] ata1.00: exception Emask 0x0 SAct 0x1000000 SErr 0x0 action 0x6
[ 22.111994] ata1.00: irq_stat 0x40000008
[ 22.111997] ata1.00: failed command: READ FPDMA QUEUED
[ 22.112003] ata1.00: cmd 60/90:c0:48:39:32/00:00:0f:00:00/40 tag 24 ncq 73728 in
res 41/84:90:8a:39:32/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 22.112005] ata1.00: status: { DRDY ERR }
[ 22.112007] ata1.00: error: { ICRC ABRT }
[ 22.112011] ata1: hard resetting link
[ 22.431783] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 22.535011] ata1.00: configured for UDMA/133
[ 22.535038] ata1: EH complete
[ 22.618877] ata1.00: exception Emask 0x0 SAct 0x1e SErr 0x0 action 0x6
[ 22.618886] ata1.00: irq_stat 0x40000008
[ 22.618891] ata1.00: failed command: READ FPDMA QUEUED
[ 22.618901] ata1.00: cmd 60/00:08:08:2c:32/01:00:0f:00:00/40 tag 1 ncq 131072 in
res 41/84:00:70:2c:32/00:01:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 22.618906] ata1.00: status: { DRDY ERR }
[ 22.618909] ata1.00: error: { ICRC ABRT }
[ 22.618920] ata1: hard resetting link
[ 22.938608] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 23.023643] ata1.00: configured for UDMA/133
[ 23.023682] ata1: EH complete
[ 53.428943] ata1.00: exception Emask 0x1 SAct 0x7fffffff SErr 0x0 action 0x6 frozen
[ 53.428953] ata1.00: irq_stat 0x40000008
[ 53.428960] ata1.00: failed command: READ FPDMA QUEUED
[ 53.428971] ata1.00: cmd 60/00:00:00:e8:31/01:00:10:00:00/40 tag 0 ncq 131072 in
res 40/00:00:00:00:00/00:00:00:00:00/00 Emask 0x5 (timeout)
[ 53.428976] ata1.00: status: { DRDY }
[ 53.428981] ata1.00: failed command: READ FPDMA QUEUED
[ 53.428990] ata1.00: cmd 60/08:08:20:fe:e9/00:00:0f:00:00/40 tag 1 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.428994] ata1.00: status: { DRDY }
[ 53.428998] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429006] ata1.00: cmd 60/08:10:28:fe:e9/00:00:0f:00:00/40 tag 2 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429010] ata1.00: status: { DRDY }
[ 53.429014] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429022] ata1.00: cmd 60/08:18:30:fe:e9/00:00:0f:00:00/40 tag 3 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429026] ata1.00: status: { DRDY }
[ 53.429029] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429037] ata1.00: cmd 60/08:20:38:fe:e9/00:00:0f:00:00/40 tag 4 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429042] ata1.00: status: { DRDY }
[ 53.429045] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429053] ata1.00: cmd 60/08:28:40:fe:e9/00:00:0f:00:00/40 tag 5 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429057] ata1.00: status: { DRDY }
[ 53.429061] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429069] ata1.00: cmd 60/08:30:48:fe:e9/00:00:0f:00:00/40 tag 6 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429073] ata1.00: status: { DRDY }
[ 53.429076] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429084] ata1.00: cmd 60/08:38:50:fe:e9/00:00:0f:00:00/40 tag 7 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429089] ata1.00: status: { DRDY }
[ 53.429092] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429100] ata1.00: cmd 60/08:40:58:fe:e9/00:00:0f:00:00/40 tag 8 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429104] ata1.00: status: { DRDY }
[ 53.429108] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429116] ata1.00: cmd 60/08:48:60:fe:e9/00:00:0f:00:00/40 tag 9 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429120] ata1.00: status: { DRDY }
[ 53.429124] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429132] ata1.00: cmd 60/08:50:68:fe:e9/00:00:0f:00:00/40 tag 10 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429136] ata1.00: status: { DRDY }
[ 53.429139] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429148] ata1.00: cmd 60/08:58:70:fe:e9/00:00:0f:00:00/40 tag 11 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429152] ata1.00: status: { DRDY }
[ 53.429155] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429163] ata1.00: cmd 60/08:60:78:fe:e9/00:00:0f:00:00/40 tag 12 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429168] ata1.00: status: { DRDY }
[ 53.429171] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429179] ata1.00: cmd 60/08:68:80:fe:e9/00:00:0f:00:00/40 tag 13 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429183] ata1.00: status: { DRDY }
[ 53.429187] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429195] ata1.00: cmd 60/08:70:18:e8:a9/00:00:16:00:00/40 tag 14 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429199] ata1.00: status: { DRDY }
[ 53.429203] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429211] ata1.00: cmd 60/08:78:90:fe:e9/00:00:0f:00:00/40 tag 15 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429215] ata1.00: status: { DRDY }
[ 53.429218] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429226] ata1.00: cmd 60/08:80:98:fe:e9/00:00:0f:00:00/40 tag 16 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429230] ata1.00: status: { DRDY }
[ 53.429234] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429242] ata1.00: cmd 60/08:88:a0:fe:e9/00:00:0f:00:00/40 tag 17 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429246] ata1.00: status: { DRDY }
[ 53.429250] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429258] ata1.00: cmd 60/08:90:a8:fe:e9/00:00:0f:00:00/40 tag 18 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429262] ata1.00: status: { DRDY }
[ 53.429265] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429273] ata1.00: cmd 60/08:98:b0:fe:e9/00:00:0f:00:00/40 tag 19 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429277] ata1.00: status: { DRDY }
[ 53.429281] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429289] ata1.00: cmd 60/08:a0:b8:fe:e9/00:00:0f:00:00/40 tag 20 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429293] ata1.00: status: { DRDY }
[ 53.429297] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429305] ata1.00: cmd 60/08:a8:c0:fe:e9/00:00:0f:00:00/40 tag 21 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429309] ata1.00: status: { DRDY }
[ 53.429312] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429320] ata1.00: cmd 60/08:b0:c8:fe:e9/00:00:0f:00:00/40 tag 22 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429325] ata1.00: status: { DRDY }
[ 53.429328] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429336] ata1.00: cmd 60/08:b8:d0:fe:e9/00:00:0f:00:00/40 tag 23 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429340] ata1.00: status: { DRDY }
[ 53.429344] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429352] ata1.00: cmd 60/08:c0:d8:fe:e9/00:00:0f:00:00/40 tag 24 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429356] ata1.00: status: { DRDY }
[ 53.429360] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429367] ata1.00: cmd 60/08:c8:e0:fe:e9/00:00:0f:00:00/40 tag 25 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429372] ata1.00: status: { DRDY }
[ 53.429375] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429383] ata1.00: cmd 60/08:d0:e8:fe:e9/00:00:0f:00:00/40 tag 26 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429387] ata1.00: status: { DRDY }
[ 53.429391] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429399] ata1.00: cmd 60/08:d8:f0:fe:e9/00:00:0f:00:00/40 tag 27 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429403] ata1.00: status: { DRDY }
[ 53.429407] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429414] ata1.00: cmd 60/08:e0:f8:fe:e9/00:00:0f:00:00/40 tag 28 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429419] ata1.00: status: { DRDY }
[ 53.429422] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429430] ata1.00: cmd 60/08:e8:00:ff:e9/00:00:0f:00:00/40 tag 29 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429435] ata1.00: status: { DRDY }
[ 53.429438] ata1.00: failed command: READ FPDMA QUEUED
[ 53.429446] ata1.00: cmd 60/08:f0:88:fe:e9/00:00:0f:00:00/40 tag 30 ncq 4096 in
res 40/00:f0:88:fe:e9/00:00:0f:00:00/40 Emask 0x1 (device error)
[ 53.429450] ata1.00: status: { DRDY }
[ 53.429458] ata1: hard resetting link
[ 53.749173] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 53.836070] ata1.00: configured for UDMA/133
[ 53.836079] ata1.00: device reported invalid CHS sector 0
[ 53.836116] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836119] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836121] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836123] sd 0:0:0:0: [sda] CDB:
[ 53.836125] cdb[0]=0x28: 28 00 0f e9 fe 20 00 00 08 00
[ 53.836133] blk_update_request: I/O error, dev sda, sector 266993184
[ 53.836148] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836151] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836153] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836154] sd 0:0:0:0: [sda] CDB:
[ 53.836155] cdb[0]=0x28: 28 00 0f e9 fe 28 00 00 08 00
[ 53.836162] blk_update_request: I/O error, dev sda, sector 266993192
[ 53.836167] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836169] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836171] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836173] sd 0:0:0:0: [sda] CDB:
[ 53.836174] cdb[0]=0x28: 28 00 0f e9 fe 30 00 00 08 00
[ 53.836180] blk_update_request: I/O error, dev sda, sector 266993200
[ 53.836185] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836187] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836189] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836190] sd 0:0:0:0: [sda] CDB:
[ 53.836191] cdb[0]=0x28: 28 00 0f e9 fe 38 00 00 08 00
[ 53.836198] blk_update_request: I/O error, dev sda, sector 266993208
[ 53.836202] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836204] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836206] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836208] sd 0:0:0:0: [sda] CDB:
[ 53.836209] cdb[0]=0x28: 28 00 0f e9 fe 40 00 00 08 00
[ 53.836215] blk_update_request: I/O error, dev sda, sector 266993216
[ 53.836220] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836222] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836224] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836225] sd 0:0:0:0: [sda] CDB:
[ 53.836226] cdb[0]=0x28: 28 00 0f e9 fe 48 00 00 08 00
[ 53.836232] blk_update_request: I/O error, dev sda, sector 266993224
[ 53.836237] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836239] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836241] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836242] sd 0:0:0:0: [sda] CDB:
[ 53.836243] cdb[0]=0x28: 28 00 0f e9 fe 50 00 00 08 00
[ 53.836249] blk_update_request: I/O error, dev sda, sector 266993232
[ 53.836253] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836255] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836257] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836259] sd 0:0:0:0: [sda] CDB:
[ 53.836260] cdb[0]=0x28: 28 00 0f e9 fe 58 00 00 08 00
[ 53.836266] blk_update_request: I/O error, dev sda, sector 266993240
[ 53.836270] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836272] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836274] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836276] sd 0:0:0:0: [sda] CDB:
[ 53.836277] cdb[0]=0x28: 28 00 0f e9 fe 60 00 00 08 00
[ 53.836283] blk_update_request: I/O error, dev sda, sector 266993248
[ 53.836287] sd 0:0:0:0: [sda] UNKNOWN Result: hostbyte=0x00 driverbyte=0x08
[ 53.836289] sd 0:0:0:0: [sda] Sense Key : 0xb [current] [descriptor]
[ 53.836291] sd 0:0:0:0: [sda] ASC=0x0 ASCQ=0x0
[ 53.836293] sd 0:0:0:0: [sda] CDB:
[ 53.836294] cdb[0]=0x28: 28 00 0f e9 fe 68 00 00 08 00
[ 53.836300] blk_update_request: I/O error, dev sda, sector 266993256
[ 53.836354] ata1: EH complete
[ 53.922776] ata1.00: exception Emask 0x0 SAct 0x20 SErr 0x0 action 0x6
[ 53.922827] ata1.00: irq_stat 0x40000008
[ 53.922855] ata1.00: failed command: READ FPDMA QUEUED
[ 53.922891] ata1.00: cmd 60/00:28:38:3f:04/01:00:10:00:00/40 tag 5 ncq 131072 in
res 41/84:00:5a:3f:04/00:01:10:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 53.922981] ata1.00: status: { DRDY ERR }
[ 53.923007] ata1.00: error: { ICRC ABRT }
[ 53.923037] ata1: hard resetting link
[ 54.242882] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 54.357940] ata1.00: configured for UDMA/133
[ 54.357967] ata1: EH complete
[ 54.413337] ata1.00: limiting speed to UDMA/100:PIO4
[ 54.413343] ata1.00: exception Emask 0x0 SAct 0x100 SErr 0x0 action 0x6
[ 54.413387] ata1.00: irq_stat 0x40000008
[ 54.413412] ata1.00: failed command: READ FPDMA QUEUED
[ 54.413445] ata1.00: cmd 60/20:40:c0:04:b1/00:00:16:00:00/40 tag 8 ncq 16384 in
res 41/84:20:d4:04:b1/00:00:16:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 54.413527] ata1.00: status: { DRDY ERR }
[ 54.413551] ata1.00: error: { ICRC ABRT }
[ 54.413578] ata1: hard resetting link
[ 54.733264] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 54.835393] ata1.00: configured for UDMA/100
[ 54.835419] ata1: EH complete
[ 54.883575] ata1.00: exception Emask 0x0 SAct 0x8 SErr 0x0 action 0x6
[ 54.883618] ata1.00: irq_stat 0x40000008
[ 54.883643] ata1.00: failed command: READ FPDMA QUEUED
[ 54.883675] ata1.00: cmd 60/08:18:e0:04:b1/00:00:16:00:00/40 tag 3 ncq 4096 in
res 41/84:08:e4:04:b1/00:00:16:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 54.883756] ata1.00: status: { DRDY ERR }
[ 54.883779] ata1.00: error: { ICRC ABRT }
[ 54.883805] ata1: hard resetting link
[ 55.203636] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 55.301754] ata1.00: configured for UDMA/100
[ 55.301780] ata1: EH complete
[ 55.357428] ata1.00: exception Emask 0x0 SAct 0x40000 SErr 0x0 action 0x6
[ 55.357474] ata1.00: irq_stat 0x40000008
[ 55.357500] ata1.00: failed command: READ FPDMA QUEUED
[ 55.357532] ata1.00: cmd 60/f0:90:e0:34:a5/00:00:0e:00:00/40 tag 18 ncq 122880 in
res 41/84:f0:ea:34:a5/00:00:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 55.357613] ata1.00: status: { DRDY ERR }
[ 55.357636] ata1.00: error: { ICRC ABRT }
[ 55.357661] ata1: hard resetting link
[ 55.677344] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 55.779200] ata1.00: configured for UDMA/100
[ 55.779228] ata1: EH complete
[ 55.954538] ata1.00: exception Emask 0x0 SAct 0xc0000 SErr 0x0 action 0x6
[ 55.954585] ata1.00: irq_stat 0x40000008
[ 55.954610] ata1.00: failed command: READ FPDMA QUEUED
[ 55.954643] ata1.00: cmd 60/00:90:00:eb:a4/01:00:0e:00:00/40 tag 18 ncq 131072 in
res 41/84:00:10:eb:a4/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 55.954725] ata1.00: status: { DRDY ERR }
[ 55.954748] ata1.00: error: { ICRC ABRT }
[ 55.954774] ata1: hard resetting link
[ 56.274496] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 56.367864] ata1.00: configured for UDMA/100
[ 56.367921] ata1: EH complete
[ 56.448401] ata1.00: limiting speed to UDMA/33:PIO4
[ 56.448412] ata1.00: exception Emask 0x0 SAct 0x4 SErr 0x0 action 0x6
[ 56.448483] ata1.00: irq_stat 0x40000008
[ 56.448524] ata1.00: failed command: READ FPDMA QUEUED
[ 56.448578] ata1.00: cmd 60/00:10:58:ec:a4/01:00:0e:00:00/40 tag 2 ncq 131072 in
res 41/84:00:fe:ec:a4/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 56.448715] ata1.00: status: { DRDY ERR }
[ 56.448753] ata1.00: error: { ICRC ABRT }
[ 56.448798] ata1: hard resetting link
[ 56.768215] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 56.856253] ata1.00: configured for UDMA/33
[ 56.856297] ata1: EH complete
[ 56.898690] ata1.00: exception Emask 0x0 SAct 0x60 SErr 0x0 action 0x6
[ 56.898770] ata1.00: irq_stat 0x40000008
[ 56.898816] ata1.00: failed command: READ FPDMA QUEUED
[ 56.898876] ata1.00: cmd 60/00:30:c8:ee:a4/01:00:0e:00:00/40 tag 6 ncq 131072 in
res 41/84:00:e8:ee:a4/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 56.899029] ata1.00: status: { DRDY ERR }
[ 56.899072] ata1.00: error: { ICRC ABRT }
[ 56.899121] ata1: hard resetting link
[ 57.218560] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 57.311513] ata1.00: configured for UDMA/33
[ 57.311542] ata1: EH complete
[ 57.355664] ata1.00: exception Emask 0x0 SAct 0x500 SErr 0x0 action 0x6
[ 57.355754] ata1.00: irq_stat 0x40000008
[ 57.355806] ata1.00: failed command: READ FPDMA QUEUED
[ 57.355873] ata1.00: cmd 60/58:50:00:ec:a4/00:00:0e:00:00/40 tag 10 ncq 45056 in
res 41/84:58:1a:ec:a4/00:00:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 57.356044] ata1.00: status: { DRDY ERR }
[ 57.356091] ata1.00: error: { ICRC ABRT }
[ 57.356145] ata1: hard resetting link
[ 57.675608] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 57.766781] ata1.00: configured for UDMA/33
[ 57.766816] ata1: EH complete
[ 57.806077] ata1.00: exception Emask 0x0 SAct 0x3000 SErr 0x0 action 0x6
[ 57.806134] ata1.00: irq_stat 0x40000008
[ 57.806164] ata1.00: failed command: READ FPDMA QUEUED
[ 57.806203] ata1.00: cmd 60/00:68:70:24:a5/01:00:0e:00:00/40 tag 13 ncq 131072 in
res 41/84:00:f2:24:a5/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 57.806302] ata1.00: status: { DRDY ERR }
[ 57.806330] ata1.00: error: { ICRC ABRT }
[ 57.806362] ata1: hard resetting link
[ 58.125961] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 58.211103] ata1.00: configured for UDMA/33
[ 58.211156] ata1: EH complete
[ 58.249769] ata1.00: exception Emask 0x0 SAct 0x18000 SErr 0x0 action 0x6
[ 58.249854] ata1.00: irq_stat 0x40000008
[ 58.249901] ata1.00: failed command: READ FPDMA QUEUED
[ 58.249962] ata1.00: cmd 60/00:80:20:27:a5/01:00:0e:00:00/40 tag 16 ncq 131072 in
res 41/84:00:a2:27:a5/00:01:0e:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 58.255626] ata1.00: status: { DRDY ERR }
[ 58.258790] ata1.00: error: { ICRC ABRT }
[ 58.261924] ata1: hard resetting link
[ 58.579657] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 58.666164] ata1.00: configured for UDMA/33
[ 58.666199] ata1: EH complete
[ 58.716707] ata1.00: exception Emask 0x0 SAct 0x4000000 SErr 0x0 action 0x6
[ 58.718539] ata1.00: irq_stat 0x40000008
[ 58.720328] ata1.00: failed command: READ FPDMA QUEUED
[ 58.722121] ata1.00: cmd 60/00:d0:68:92:5c/01:00:0f:00:00/40 tag 26 ncq 131072 in
res 41/84:00:76:92:5c/00:01:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 58.725736] ata1.00: status: { DRDY ERR }
[ 58.727553] ata1.00: error: { ICRC ABRT }
[ 58.728965] ata1: hard resetting link
[ 59.046670] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 59.132488] ata1.00: configured for UDMA/33
[ 59.132515] ata1: EH complete
[ 59.180459] ata1.00: exception Emask 0x0 SAct 0x20000000 SErr 0x0 action 0x6
[ 59.181979] ata1.00: irq_stat 0x40000008
[ 59.182990] ata1.00: failed command: READ FPDMA QUEUED
[ 59.183943] ata1.00: cmd 60/f8:e8:68:93:5c/00:00:0f:00:00/40 tag 29 ncq 126976 in
res 41/84:f8:6a:93:5c/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 59.185831] ata1.00: status: { DRDY ERR }
[ 59.186778] ata1.00: error: { ICRC ABRT }
[ 59.187715] ata1: hard resetting link
[ 59.507035] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 59.610051] ata1.00: configured for UDMA/33
[ 59.610080] ata1: EH complete
[ 59.661766] ata1.00: exception Emask 0x0 SAct 0x80 SErr 0x0 action 0x6
[ 59.663154] ata1.00: irq_stat 0x40000008
[ 59.664089] ata1.00: failed command: READ FPDMA QUEUED
[ 59.665027] ata1.00: cmd 60/98:38:60:94:5c/00:00:0f:00:00/40 tag 7 ncq 77824 in
res 41/84:98:64:94:5c/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 59.666916] ata1.00: status: { DRDY ERR }
[ 59.669774] ata1.00: error: { ICRC ABRT }
[ 59.672954] ata1: hard resetting link
[ 59.990695] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 60.087554] ata1.00: configured for UDMA/33
[ 60.087600] ata1: EH complete
[ 60.217903] ata1.00: exception Emask 0x0 SAct 0x80 SErr 0x0 action 0x6
[ 60.219413] ata1.00: irq_stat 0x40000008
[ 60.220456] ata1.00: failed command: READ FPDMA QUEUED
[ 60.221440] ata1.00: cmd 60/20:38:00:1b:3e/00:00:0f:00:00/40 tag 7 ncq 16384 in
res 41/84:20:18:1b:3e/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 60.223332] ata1.00: status: { DRDY ERR }
[ 60.224269] ata1.00: error: { ICRC ABRT }
[ 60.225206] ata1: hard resetting link
[ 60.544531] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 60.653686] ata1.00: configured for UDMA/33
[ 60.653713] ata1: EH complete
[ 60.701540] ata1.00: exception Emask 0x0 SAct 0x400 SErr 0x0 action 0x6
[ 60.703016] ata1.00: irq_stat 0x40000008
[ 60.704106] ata1.00: failed command: READ FPDMA QUEUED
[ 60.705056] ata1.00: cmd 60/88:50:78:1b:3e/00:00:0f:00:00/40 tag 10 ncq 69632 in
res 41/84:88:78:1b:3e/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 60.706949] ata1.00: status: { DRDY ERR }
[ 60.707884] ata1.00: error: { ICRC ABRT }
[ 60.708824] ata1: hard resetting link
[ 61.028237] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 61.142293] ata1.00: configured for UDMA/33
[ 61.142319] ata1: EH complete
[ 61.195399] ata1.00: exception Emask 0x0 SAct 0x8000 SErr 0x0 action 0x6
[ 61.197750] ata1.00: irq_stat 0x40000008
[ 61.200089] ata1.00: failed command: READ FPDMA QUEUED
[ 61.201690] ata1.00: cmd 60/20:78:10:39:38/00:00:0f:00:00/40 tag 15 ncq 16384 in
res 41/84:20:14:39:38/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 61.204897] ata1.00: status: { DRDY ERR }
[ 61.206484] ata1.00: error: { ICRC ABRT }
[ 61.208071] ata1: hard resetting link
[ 61.525313] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 61.630818] ata1.00: configured for UDMA/33
[ 61.630845] ata1: EH complete
[ 61.675724] ata1.00: exception Emask 0x0 SAct 0x40000 SErr 0x0 action 0x6
[ 61.677345] ata1.00: irq_stat 0x40000008
[ 61.678943] ata1.00: failed command: READ FPDMA QUEUED
[ 61.680539] ata1.00: cmd 60/50:90:30:39:38/00:00:0f:00:00/40 tag 18 ncq 40960 in
res 41/84:50:70:39:38/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 61.683756] ata1.00: status: { DRDY ERR }
[ 61.685369] ata1.00: error: { ICRC ABRT }
[ 61.686586] ata1: hard resetting link
[ 62.005676] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 62.108289] ata1.00: configured for UDMA/33
[ 62.108316] ata1: EH complete
[ 62.162783] ata1.00: exception Emask 0x0 SAct 0x400000 SErr 0x0 action 0x6
[ 62.164411] ata1.00: irq_stat 0x40000008
[ 62.166015] ata1.00: failed command: READ FPDMA QUEUED
[ 62.167617] ata1.00: cmd 60/20:b0:d8:c3:3d/00:00:0f:00:00/40 tag 22 ncq 16384 in
res 41/84:20:d8:c3:3d/00:00:0f:00:00/00 Emask 0x410 (ATA bus error) <F>
[ 62.170837] ata1.00: status: { DRDY ERR }
[ 62.172433] ata1.00: error: { ICRC ABRT }
[ 62.173698] ata1: hard resetting link
[ 62.492749] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 310)
[ 62.607944] ata1.00: configured for UDMA/33
[ 62.607974] ata1: EH complete
Output of smartctl -a /dev/sda
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.19.3-3-ARCH] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Laptop SSHD
Device Model: ST1000LM014-SSHD-8GB
Serial Number: W3829AM6
LU WWN Device Id: 5 000c50 07be01372
Firmware Version: LVD3
User Capacity: 1,000,204,886,016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 1.5 Gb/s)
Local Time is: Sun May 10 11:12:02 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 150) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 198) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x1081) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 117 099 006 Pre-fail Always - 158141600
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 429
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 073 060 030 Pre-fail Always - 4319585187
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1864
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 437
184 End-to-End_Error 0x0032 089 089 099 Old_age Always FAILING_NOW 11
187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 069 052 045 Old_age Always - 31 (Min/Max 25/31)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 50
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 6179
194 Temperature_Celsius 0x0022 031 048 000 Old_age Always - 31 (0 19 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 13 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13 occurred at disk power-on lifetime: 1779 hours (74 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 10 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
60 00 b0 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
60 00 30 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 09:58:40.403 FLUSH CACHE EXT
61 00 08 ff ff ff 4f 00 09:58:40.403 WRITE FPDMA QUEUED
Error 12 occurred at disk power-on lifetime: 1722 hours (71 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 00 ff ff ff 4f 00 00:01:28.048 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:01:28.048 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:01:28.047 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:01:28.047 READ FPDMA QUEUED
60 00 30 50 3a c5 4e 00 00:01:28.045 READ FPDMA QUEUED
Error 11 occurred at disk power-on lifetime: 1537 hours (64 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 00 ff ff ff 4f 00 00:00:35.199 READ FPDMA QUEUED
60 00 20 ff ff ff 4f 00 00:00:35.198 READ FPDMA QUEUED
60 00 08 10 10 2b 4f 00 00:00:35.188 READ FPDMA QUEUED
60 00 e0 20 e0 78 4f 00 00:00:35.187 READ FPDMA QUEUED
60 00 90 68 e1 78 4f 00 00:00:35.185 READ FPDMA QUEUED
Error 10 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 a0 ff ff ff 4f 00 00:00:15.374 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:15.373 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:15.373 READ FPDMA QUEUED
60 00 80 ff ff ff 4f 00 00:00:15.370 READ FPDMA QUEUED
60 00 68 ff ff ff 4f 00 00:00:15.370 READ FPDMA QUEUED
Error 9 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 08 e0 9e 31 4f 00 00:00:15.146 READ FPDMA QUEUED
60 00 a8 ff ff ff 4f 00 00:00:15.073 READ FPDMA QUEUED
60 00 18 ff ff ff 4f 00 00:00:15.072 READ FPDMA QUEUED
60 00 98 ff ff ff 4f 00 00:00:15.072 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:00:15.068 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Is this software bug or hard drive failure? Thanks in advance.Thanks for your answers.
2ion wrote:
Not necessarily, this is a Seagate hard drive. AFAIK Seek Error Rate and Raw Read Error Rate are 48bit values where the lower 24bit encode the total number of sectors read/saught (which overflows to zero) and the upper 24bit encode the acutal errors.
smartctl -v 1,hex48 -v 7,hex48 -a /dev/sda
should display OP's data in a usuable format.
In fact, I turned my recently purchased laptop in for a hard disk replacement of almost the same type as OP (ST500LM000-SSHD-8GB) twice, but all three drives of this type I had provided SMART values which were more of an oracle rather than data useful for monitoring purposes. Forums are full with people unsure about what to do with this kind of drives. If you google for the End-to-End errors with Seagate drives (here marked as FAILING!), you'll find people reporting that Seagate's own tools do not report any errors despite the attribute in question being reported by monitoring tools just as bad... Seagate is the horror. So, I'd say that it is rather uncertain whether the SMART values are connected to the actual drive failing or a faulty cable.
OP, did you see these errors from the beginning or after a certain time, or perhaps after a kernel upgrade? Did you check the drive's cable? What was the situation before these errors showed up (maybe under Windows?)
smartctl -v 1,hex48 -v 7,hex48 -a /dev/sda
smartctl 6.3 2014-07-26 r3976 [x86_64-linux-3.19.3-3-ARCH] (local build)
Copyright (C) 2002-14, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Model Family: Seagate Laptop SSHD
Device Model: ST1000LM014-SSHD-8GB
Serial Number: W3829AM6
LU WWN Device Id: 5 000c50 07be01372
Firmware Version: LVD3
User Capacity: 1,000,204,886,016 bytes [1,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: In smartctl database [for details use: -P show]
ATA Version is: ACS-2, ACS-3 T13/2161-D revision 3b
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Mon May 11 12:09:29 2015 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
See vendor-specific Attribute list for marginal Attributes.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 150) seconds.
Offline data collection
capabilities: (0x73) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 198) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x1081) SCT Status supported.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 115 099 006 Pre-fail Always - 0x000005184840
3 Spin_Up_Time 0x0003 097 097 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 433
5 Reallocated_Sector_Ct 0x0033 100 100 010 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 073 060 030 Pre-fail Always - 0x0001017be679
9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1880
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 100 100 020 Old_age Always - 441
184 End-to-End_Error 0x0032 089 089 099 Old_age Always FAILING_NOW 11
187 Reported_Uncorrect 0x0032 098 098 000 Old_age Always - 2
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
189 High_Fly_Writes 0x003a 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 061 052 045 Old_age Always - 39 (Min/Max 37/39)
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age Always - 50
193 Load_Cycle_Count 0x0032 097 097 000 Old_age Always - 6282
194 Temperature_Celsius 0x0022 039 048 000 Old_age Always - 39 (0 19 0 0 0)
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always - 0
254 Free_Fall_Sensor 0x0032 100 100 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 13 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 13 occurred at disk power-on lifetime: 1779 hours (74 days + 3 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 10 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
60 00 b0 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
60 00 30 ff ff ff 4f 00 09:58:41.053 READ FPDMA QUEUED
ea 00 00 00 00 00 a0 00 09:58:40.403 FLUSH CACHE EXT
61 00 08 ff ff ff 4f 00 09:58:40.403 WRITE FPDMA QUEUED
Error 12 occurred at disk power-on lifetime: 1722 hours (71 days + 18 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 00 ff ff ff 4f 00 00:01:28.048 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:01:28.048 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:01:28.047 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:01:28.047 READ FPDMA QUEUED
60 00 30 50 3a c5 4e 00 00:01:28.045 READ FPDMA QUEUED
Error 11 occurred at disk power-on lifetime: 1537 hours (64 days + 1 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 00 ff ff ff 4f 00 00:00:35.199 READ FPDMA QUEUED
60 00 20 ff ff ff 4f 00 00:00:35.198 READ FPDMA QUEUED
60 00 08 10 10 2b 4f 00 00:00:35.188 READ FPDMA QUEUED
60 00 e0 20 e0 78 4f 00 00:00:35.187 READ FPDMA QUEUED
60 00 90 68 e1 78 4f 00 00:00:35.185 READ FPDMA QUEUED
Error 10 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 a0 ff ff ff 4f 00 00:00:15.374 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:15.373 READ FPDMA QUEUED
60 00 08 ff ff ff 4f 00 00:00:15.373 READ FPDMA QUEUED
60 00 80 ff ff ff 4f 00 00:00:15.370 READ FPDMA QUEUED
60 00 68 ff ff ff 4f 00 00:00:15.370 READ FPDMA QUEUED
Error 9 occurred at disk power-on lifetime: 1525 hours (63 days + 13 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
40 51 00 ff ff ff 0f Error: UNC at LBA = 0x0fffffff = 268435455
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
60 00 08 e0 9e 31 4f 00 00:00:15.146 READ FPDMA QUEUED
60 00 a8 ff ff ff 4f 00 00:00:15.073 READ FPDMA QUEUED
60 00 18 ff ff ff 4f 00 00:00:15.072 READ FPDMA QUEUED
60 00 98 ff ff ff 4f 00 00:00:15.072 READ FPDMA QUEUED
60 00 00 ff ff ff 4f 00 00:00:15.068 READ FPDMA QUEUED
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 1871 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
These errors just appeared, not after upgrade and I didn't get them in the beginning. The situation before errors - everything worked exactly the same, I see no difference in performance, except that few seconds long freeze that sometimes happen. Can't tell about Windows, I have it pre-installed but never used it so I can't compare. I didn't check the cable, and I'd rather not do that - I don't want to mess with hardware, if I do something wrong I lose the warranty. If something is wrong then I'd rather have it checked and fixed by someone who knows how to do that (and for free, because I still have the warranty). -
I'm trying to burn playlists onto a cd from itunes. I keep getting a "medium write error" message. What does this mean? I heard that this may mean that I should try burning at a slower speed. I tried this and that didn't help. I also heard that I may need to use a different brand of CD-R disc. I have not tried this yet. I also heard that it could be a software issue or disc drive issue. I recently updated my macbook pro software from tiger to snow leapord. Do you think this could have affected my itunes playlist burning capabilities? Thanks for the help.
A system upgrade should not have affected anything. When did you notice the loss in functionality?
Try different media. 2011 post on optical media - http://discussions.apple.com/thread.jspa?threadID=2754858&
Apple Portables: Resetting the System Management Controller (SMC) - http://support.apple.com/kb/HT1411
Realize that a MBP that came with Tiger is an old computer and optical drives do not last forever.
You could try a drive cleaning disc to remove dust. Don't be overly optimistic. I suspect it is an old drive issue. -
ERROR CODE 2STF/8/3: S-ATA BUS O-Master
I was running Pro ToolsLE on my iMac G5 and then all operations stopped or froze, I forced quit, lost what I was working on when it stopped. Then I tried to restart after deleating the pro tools prefs file and the gray screen with apple symbol and indicator comes up and doesn't continue to boot up.
I ran Tech tools from the install disc and the ERROR CODE 2STF/8/3: S-ATA BUS O-Master comes up. After researching further I think the Hard Drive has Failed!!
Can this be true? I have not used the computer that much. I will be calling Apple Care. Has anyone else experienced this, and is my iMac G5 not as reliable as I thought?Welcome to Discussions - hard drives can fail at any point, the amount of use is no indication of longevity. My iMac G5 is a Rev A, and (fingers crossed) the original drive is still working flawlessly. In every batch there are some that will fail prematurely and others that will last long past their fail date. Please do call Apple Care and see what they say.
See if there's any way you can put your computer in Target Disk Mode and get your data off the drive before it goes in for repair.
Miriam -
Disk utility reports failing hard drive with error code STF/8/3:2 ATA BUS 0
My imac G5 (running Tiger) suddenly decided not to boot past the grey apple screen with the spinning wheel. I ran the disk utility and received error code STF/8/3:2 ATA BUS 0 MASTER on the mass storage test. I tried to run repair and only received a message "fatal hard drive error etc... back up, recover asap... I could not access the disk so I connected my new MacBook Pro by firewire in target disk mode. My HD shows up however, "nothing" shows up under when my "user" file. All I care about saving is my iphoto library. Everything else is trivial. Can someone Please help me? Is there any way I will be able to save this file?
Message was edited by: Elizabeth BursonWelcome to Discussions - you can try DiskWarrior and see if it can retrieve some of your data. You can also take it in to Apple with an external fire wire drive you have purchased elsewhere (cheaper) and see if they can transfer the data. You can then install the external into your computer.
-
Burning Songs from itunes to CD Error(4000)
For the longest time with my old school 20g could not burn discs from itunes to a disc.
Got a new 80g with newer iTunes. For a short time could burn discs.
I have and had got this message
the attempt to burn a disc faile. An unkown error occorred(4000)
Please helphttp://discussions.apple.com/message.jspa?messageID=1783768#1783768
Incidentally, that forum is more appropriate for your question so you might want to ask it there if this fix doesn't work. -
Error encountered while collecting the data from JMS topic bus
Iam encountering a problem while collecting the data from JMS topic bus and pushing the data to BAM.On the DesignStudio window, after I click on “update” button in the plan window to run the plan I get the following exception messages:
IMessageSourceReceiver->messageReceive:
javax.naming.CommunicationException: Connection refused: connect
at com.evermind.server.rmi.RMIClient.lookup(RMIClient.java:292)
at
com.evermind.server.rmi.RMIClientContext.lookup(RMIClientContext.java:51)
at javax.naming.InitialContext.lookup(InitialContext.java:347)
at
iteration.enterpriselink.sources.JMSConsumer.start(JMSConsumer.java:85)
at
iteration.enterpriselink.sources.JMSMessageSourceReceiverImpl.jmsConsumerS
tart(JMSMessageSourceReceiverImpl.java:1001)
at
iteration.enterpriselink.sources.JMSMessageSourceReceiverImpl.messageRecei
ve(JMSMessageSourceReceiverImpl.java:326)
Caused by: java.net.ConnectException: Connection refused: connect
at java.net.PlainSocketImpl.socketConnect(Native Method)
at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:305)
at
java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:171)
at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:158)
at java.net.Socket.connect(Socket.java:426)
at java.net.Socket.connect(Socket.java:376)
at java.net.Socket.<init>(Socket.java:291)
at java.net.Socket.<init>(Socket.java:147)
at
com.evermind.server.rmi.RMIClientConnection.createSocket(RMIClientConnecti
on.java:682)
at
oracle.oc4j.rmi.ClientSocketRmiTransport.createNetworkConnection(ClientSoc
ketRmiTransport.java:58)
at
oracle.oc4j.rmi.ClientRmiTransport.connectToServer(ClientRmiTransport.java
:78)
at
oracle.oc4j.rmi.ClientSocketRmiTransport.connectToServer(ClientSocketRmiTr
ansport.java:68)
at
com.evermind.server.rmi.RMIClientConnection.connect(RMIClientConnection.ja
va:646)
at
com.evermind.server.rmi.RMIClientConnection.sendLookupRequest(RMIClientCon
nection.java:190)
at
com.evermind.server.rmi.RMIClientConnection.lookup(RMIClientConnection.jav
a:174)
at com.evermind.server.rmi.RMIClient.lookup(RMIClient.java:283)
... 5 more
[Oracle BAM Enterprise Link error code: 0x75 -- 0x1, 0x75 -- 0x3A]
Error during Message Receive operation.
[Oracle BAM Enterprise Link error code: 0x75 -- 0x1, 0x75 -- 0x3B]The error msg says that your BAM server cannot connect to your JMS provider. Make sure your configs are all ok, in EL DesignStudio, BAMArchitect EMSdefinition, etc. You can refer to the samples and technotes and tutorials to understand these details. If you are following the steps in the technote etc. pl verify your oc4j container is running, and oc4j version and 'jndi path' is ok. Give the doc name, pg number and step where you are getting this error.
-
Error Code: 2STF/8/3: S-ATA BUS 0 - MASTER
My iMac G5 is hanging up at times (spinning wheel) and then hangs for 30 minutes or more on restart before eventually booting up. I did a hardware test which revealed the following error: "Error Code: 2STF/8/3: S-ATA BUS 0 - MASTER" in the mass storage portion of the test.
Any suggestions on next steps?Please back up your data immediately, preferably by cloning them to n external firewire drive using SuperDuper!.
It looks as if your hard drive is about to bite the dust, new large ones are not at all expensive, and with your data cloned, it's very easy to migrate to a new drive.
Let us know how things work out for you, -
Cannot burn CD from itunes.
The thing is, they are in the unprotected format? (
They are protected WMA from when you RIP'd them with WMP. iTunes will not read them.
Go to WMP Tools -> Rip Music.
Under Rip settings, it is set to *Windows Media Audio* and most likely *Copy protect music* is ticked. This is how it is protected.
You will need to reRIP them all from CD. -
ITunes Burning Error 4200 - Windows XP
I recently purchased an HPa1130n running iTunes 4.9. It was working fine up until a week ago when I started getting errors that say "cancelling burn... unknown error 4200". I have read a few posts in this forum and would like for someone to help me get my system back up and burning. I've done the obvious (slowing the speed, trying different disks, etc). I've also checked my DMA settings to ensure that they are correct. From what I have read so far, I think iTunes is having trouble communicating with my CD Burner.
Help me obi-wan-kenobi.. you're my only hope...
Here is some of my info:
Hardware Information
CPU : AMD Athlon 64 Processor 3500+ 2190 MHz
Bus Speed : 199 MHz
Motherboard : MSI ALBACORE
System : HP a1130n
BIOS : Phoenix 3.12
Memory : 1024 MB (129ns)
Sound : Realtek AC97 Audio
Video : ATI RADEON Xpress 200 Series
Drive Information
Drive : HL-DT-ST DVDRRW GWA-4166B
Type : DVD±R/RW DL Recorder
Firmware Version : 1823
Buffer Size : 2 MB
Lower Filters
Driver : PxHelp20
Description : Px Engine Device Driver for Windows 2000/XP
Version : 2.03.27a
Company : Sonic Solutions
Upper Filters
Driver : GEARAspiWDM
Description : CDRom Class Filter Driver
Version : 2.0.4.0
Company : GEAR Software Inc.Thanks for the prompt response b.
Here are some of the things you asked about:
(1) - The diagnostic log:
Microsoft Windows XP Professional Service Pack 2 (Build 2600)
iTunes 4.9.0.17
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.1
LowerFilters: PxHelp20 (2.0.0.0),
UpperFilters: GEARAspiWDM (2.0.4.3),
Video Driver: VisionTek XTASY X300 SE Hypermemory
IDE\DiskST3250823AS____________________________3.03___, Bus Type ATA, Bus Address [0,0]
USBSTOR\DiskGenericUSB_CF_Reader__1.01, Bus Type USB
USBSTOR\DiskGenericUSB_MS_Reader__1.03, Bus Type USB
USBSTOR\DiskGenericUSB_SD_Reader__1.00, Bus Type USB
USBSTOR\DiskGenericUSB_SM_Reader__1.02, Bus Type USB
IDE\CdRomHL-DT-STDVDRRW_GWA-4166B_______________1823___, Bus Type ATA, Bus Address [0,0]
IDE\CdRomIDE-DVDDROM6216________________________HD07___, Bus Type ATA, Bus Address [1,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some Dell computers need an update to the ATA bus driver before iTunes recognizes CDs. If you have a Dell computer, check the Dell support website for details.
E: HL-DT-ST DVDRRW GWA-4166B, Rev 1823
Drive is empty.
F: IDE-DVD DROM6216, Rev HD07
Drive is empty.
(2) New software added
I recently installed NERO then updated to 6.6 trial. I suspect that this has something to do with it as the last time i burned a CD sucessfully was a day before I installed/updated NERO.
(3) I tried to alternatively burn in windows media player and was also unsucessful.
(4) I see a ton of 7 or 8 events ranging from 100, 101, 102, 103 that are related to database engines but nothing related to iTunes. I see two ACEEventLogs from today:
0000000001: 2005-09-03 12:40:07:203 Systemtray cannot start - ACE Runtime not detected
Error Called by: ATI.ACE.CLI.EXE.CLI::Main processID:00348 threadID:(CLISystemtray ) domainName:(CLI.exe ) assemblyName:(CLI, Version=1.2.2006.283, Culture=neutral, PublicKeyToken=90ba9c70f846762e)
(5) It just got worse. I attempted to burn another disk and now I don't even get the error. When prompted to insert a blank disk and after clicking the burn icon, the top grey screen just blinks "checking media" a bunch of times then it times out. I don't even get to the "preparing to write" stage.
Thanks again!
RR -
ITunes won't recognize my CD burner, error message -43 on CD diagnostics
I hope there is someone who can help me. I am at my wits end with this! I cannot burn any cd's using iTunes--it does not recognize that I have burning capablities. I have tried repairing and reinstalling iTunes, because the very first error message I get when opening iTunes reads like this "The registry settings used by the iTunes drivers for importing and burning CDs and DVDs are missing. This can happen as a result of installing other CD burning software. Please reinstall iTunes". I have done this about 20 times already. Then when I try to run CD diagnostic, this is what I get:
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
Sony Corporation PCV-RZ22G(UC)
iTunes 6.0.1.3
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
LowerFilters: PXHELP20 (2.0.0.0), AFS2K (3.1.21.0),
UpperFilters: #Ǚ
Video Driver: RADEON 9600 SERIES\RADEON 9600 SERIES
IDE\DiskMaxtor6Y160L0_________________________YAR41VW0, Bus Type ATA, Bus Address [0,0]
MEMSTPCI\Disk, Bus Type UNKNOWN
USBSTOR\DiskApple__iPod____________1.62IDECdRomSAMSUNG_CD-ROM_SC-140C__________________A101___, Bus Type ATA, Bus Address [1,0]
IDE\CdRomSONYDVD_RW_DW-U12A_____________________2.0a___, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is administrator.
Failed loading CD / DVD drives, error -43. Try doing a repair install on iTunes from the "Add or Remove Programs" control panel.
I am really unhappy with this problem, considering that I can use Windows Media Player with no problem whatsoever. Now I have purchased all kinds of music off of iTunes and can't even burn a CD--what a waste of money. I hope someone has a suggestion for me. When I tried to email to the iTunes support they told me they didn't handle this type of problem, and I'd have to call their technical help line and pay whatever fee they charge for calls. Please help! Or else I guess my husband wasted $400 on a video iPod that's worthless.Here's my diagnostics:
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
Sony Corporation PCV-RZ22G(UC)
iTunes 6.0.1.3
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
LowerFilters: PXHELP20 (2.0.0.0), AFS2K (3.1.21.0),
UpperFilters: ࢸ"� ᆌ0ŘNT AUTHORITY\SYSTEMɀŞ쓠睎谘睠谘睠범 Ф
Video Driver: RADEON 9600 SERIES\RADEON 9600 SERIES
IDE\DiskMaxtor6Y160L0_________________________YAR41VW0, Bus Type ATA, Bus Address [0,0]
MEMSTPCI\Disk, Bus Type UNKNOWN
IDE\CdRomSAMSUNGCD-ROM_SC-140C__________________A101___, Bus Type ATA, Bus Address [1,0]
IDE\CdRomSONYDVD_RW_DW-U12A_____________________2.0a___, Bus Type ATA, Bus Address [0,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
Current user is administrator.
Failed loading CD / DVD drives, error -43. Try doing a repair install on iTunes from the "Add or Remove Programs" control panel.
Thanks very much Toonz. -
Hello!
So I've read all the helpful answers about this, and have tried every fix, but nothing works. Every discussion thread is super old and I wonder if there is anything more up-to-date?
This registry fix... in this thread...last post.... MIGHT be my problem, (and I suspect that it is) but the directions are confusing and don't match my computer's registery or driver details.
https://discussions.apple.com/message/2904875#2904875
If someone can interpret these a little clearer or to match my particular computer it might be helpful. I can provide more info on this if needed.
Some information:
I have a Toshiba laptop with a MATSHITA DVD RAM UJ 850S driver.
(I DO NOT have a Sony driver)
I have the 4280 error. I ALSO have the 4450 error.
It happens every time I burn no matter what brand of disc Im using or speed Im burning at.
Either it will burn a few songs and then cancel, or it will cancel before it starts to burn.
I can burn DVDs with my DVD copying software.
I CANNOT burn CDs with Windows Media Player or Real Player or anything else.
There are no needed updates to my driver. The computer tells me that everything is up-to-date.
I have had this problem for over a year and a half and have not found a fix yet.
Here is the diagnostic and thank you very much for taking the time to help me!
Microsoft Windows Vista Home Basic Edition Service Pack 2 (Build 6002)
TOSHIBA Satellite A135
iTunes 10.4.0.80
QuickTime 7.7
FairPlay 1.12.20
Apple Application Support 2.0.1
iPod Updater Library 10.0d2
CD Driver 2.2.0.1
CD Driver DLL 2.1.1.1
Apple Mobile Device 3.4.1.2
Apple Mobile Device Driver 1.57.0.0
Bonjour 3.0.0.2 (333.2)
Gracenote SDK 1.9.1.485
Gracenote MusicID 1.9.1.102
Gracenote Submit 1.9.1.133
Gracenote DSP 1.9.1.43
iTunes Serial Number 0019B2300A61A3D0
Current user is not an administrator.
The current local date and time is 2011-08-28 12:51:07.
iTunes is not running in safe mode.
WebKit accelerated compositing is enabled.
HDCP is not supported.
Core Media is not supported. (16005)
Video Display Information
Intel Corporation, Mobile Intel(R) 945 Express Chipset Family
Intel Corporation, Mobile Intel(R) 945 Express Chipset Family
**** External Plug-ins Information ****
No external plug-ins installed.
Genius ID: 9af17f30afbca638be116b77222c3c6d
**** Network Connectivity Tests ****
Network Adapter Information
Adapter Name: {37861A6F-A564-43D7-84B0-5BCF9B6D1C6E}
Description: Atheros AR5006EG Wireless Network Adapter
IP Address: 192.168.1.106
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.1.1
DHCP Enabled: Yes
DHCP Server: 192.168.1.1
Lease Obtained: Sun Aug 28 11:08:04 2011
Lease Expires: Mon Aug 29 11:08:04 2011
DNS Servers: 68.87.69.150
68.87.85.102
192.168.1.1
Adapter Name: {77214E6C-06F6-4AE7-82E5-52A93D18CA7B}
Description: Realtek RTL8101 Family PCI-E Fast Ethernet NIC (NDIS 6.0)
IP Address: 0.0.0.0
Subnet Mask: 0.0.0.0
Default Gateway: 0.0.0.0
DHCP Enabled: Yes
DHCP Server:
Lease Obtained: Wed Dec 31 16:00:00 1969
Lease Expires: Wed Dec 31 16:00:00 1969
DNS Servers:
Active Connection: LAN Connection
Connected: Yes
Online: Yes
Using Modem: No
Using LAN: Yes
Using Proxy: No
SSL 3.0 Support: Enabled
TLS 1.0 Support: Enabled
Firewall Information
Windows Firewall is on.
iTunes is NOT enabled in Windows Firewall.
Connection attempt to Apple web site was successful.
Connection attempt to browsing iTunes Store was successful.
Connection attempt to purchasing from iTunes Store was successful.
Connection attempt to iPhone activation server was successful.
Connection attempt to firmware update server was successful.
Connection attempt to Gracenote server was successful.
Last successful iTunes Store access was 2011-08-28 12:45:37.
**** CD/DVD Drive Tests ****
No drivers in LowerFilters.
UpperFilters: GEARAspiWDM (2.2.0.1),
D: MATSHITA DVD-RAM UJ-850S, Rev 1.90
Drive is empty.
Error Correction is turned on for importing audio CDs.
The last failed audio CD burn had error code 4450(0x00001162). It happened on drive D: MATSHITA DVD-RAM UJ-850S on CDR media at speed 24X.
**** Device Connectivity Tests ****
iPodService 10.4.0.80 is currently running.
iTunesHelper 10.4.0.80 is currently running.
Apple Mobile Device service 3.3.0.0 is currently running.
Universal Serial Bus Controllers:
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C8. Device is working properly.
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27C9. Device is working properly.
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CA. Device is working properly.
Intel(R) 82801G (ICH7 Family) USB Universal Host Controller - 27CB. Device is working properly.
Intel(R) 82801G (ICH7 Family) USB2 Enhanced Host Controller - 27CC. Device is working properly.
FireWire (IEEE 1394) Host Controllers:
Texas Instruments OHCI Compliant IEEE 1394 Host Controller. Device is working properly.
Most Recent Devices Not Currently Connected:
iPod shuffle (2nd Generation) running firmware version 1.0.4
Serial Number: 5C706ANCXQY
iPhone 4 (CDMA) running firmware version 4.2.10
Serial Number: C8QG2SDDDDP8
**** Device Sync Tests ****
No iPod, iPhone, or iPad found.I forgot to put the diagnostics in. Hopefully this will helps
Microsoft Windows XP Professional Service Pack 2 (Build 2600)
Dell Inc. Dimension 5100
iTunes 7.1.1.5
CD Driver 2.0.6.1
CD Driver DLL 2.0.6.2
LowerFilters: PxHelp20 (2.0.0.0), drvmcdb (1.0.0.1), sscdbhk5 (1.0.0.1),
UpperFilters: GEARAspiWDM (2.0.6.1),
Current user is an administrator.
Video Display Information:
RADEON X300 SE 128MB HyperMemory
RADEON X300 SE 128MB HyperMemory Secondary
Connected Device Information:
DiskDrive, SAMSUNG HD160JJ, Bus Type ATA, Bus Address [0,0]
CDROM, HL-DT-ST DVD-ROM GDR8163B, Bus Type ATA, Bus Address [0,0]
CDROM, _NEC DVD+-RW ND-3530A, Bus Type ATA, Bus Address [1,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some computers need an update to the ATA or IDE bus driver, or Intel chipset. If iTunes has problems recognizing CDs or hanging or crashing while importing or burning CDs, check the support site for the manufacturer of your computer or motherboard.
D: HL-DT-ST DVD-ROM GDR8163B, Rev 0D20
Drive is empty.
E: _NEC DVD+-RW ND-3530A, Rev 102B
Drive is empty.
The last failed audio CD burn had error code 4280(0x000010b8). It happened on drive E: _NEC DVD+-RW ND-3530A on CDR media at speed 16X. -
Itunes freezes when I attempt to burn CD from playlist
When I try to burn a CD from a playlist, all goes well until I click on to the pulsating "Burn Disc" Icon. Then, itunes freezes. I cannot execute any function at that point other than to use Windows Task Manager to shut down itunes. I read the posts in this section and tried the remedy of installing the GEAR installer to remove gearsec.exe and GEARSEC security with GEARsoftware. Contrary to the instructions, the software never asked me if I wanted gearsec.exe removed. That didn't solve the problem. This is a new problem that I did not experience in the past as I have burned several CD's from itunes before. I am now using itunes version 4.9.0.17 with Windows XP (Home Edition) with SP2. I will appreciate any directions that you can give me to correct this problem. Below are the results of my CD Diagnostic Check that I ran through itunes:
Microsoft Windows XP Home Edition Service Pack 2 (Build 2600)
iTunes 4.9.0.17
CD Driver 2.0.4.3
CD Driver DLL 2.0.3.2
LowerFilters: Cdr4_xp (7.1.0.190),
UpperFilters: GEARAspiWDM (2.0.4.3), Cdralw2k (7.1.0.189), pwd_2k (7.1.0.189),
Video Driver: NVIDIA GeForce FX 5200 GeForce FX 5200
Check the website of your computer manufacturer or video card vendor to verify that you have the latest video drivers.
IDE\DiskST380011A______________________________3.16___, Bus Type ATA, Bus Address [0,0]
USBSTOR\DiskHDS722516VLAT20___________, Bus Type USB
IDE\CdRomJLMSDVD-ROM_XJ-HD166___________________DD05___, Bus Type ATA, Bus Address [0,0]
IDE\CdRomNEC_DVD+RW_ND-1100A____________________10FD___, Bus Type ATA, Bus Address [1,0]
If you have multiple drives on the same IDE or SCSI bus, these drives may interfere with each other.
Some Dell computers need an update to the ATA bus driver before iTunes recognizes CDs. If you have a Dell computer, check the Dell support website for details.
D: JLMS DVD-ROM XJ-HD166, Rev DD05
Audio CD in drive.
Found 15 songs on CD, playing time 28:41 on Audio CD.
Track 1, start time 00:02:00
Track 2, start time 00:30:60
Track 3, start time 01:32:42
Track 4, start time 03:24:07
Track 5, start time 05:04:68
Track 6, start time 06:51:51
Track 7, start time 10:02:35
Track 8, start time 12:02:37
Track 9, start time 14:38:49
Track 10, start time 17:10:39
Track 11, start time 18:57:12
Track 12, start time 20:32:00
Track 13, start time 22:57:07
Track 14, start time 25:21:43
Track 15, start time 27:20:53
Check the website of your computer or drive manufacturer to verify that you have the latest firmware for your CD / DVD drive.
Audio CD reading succeeded.
E: _NEC DVD+RW ND-1100A, Rev 10FD
Audio CD in drive.
Found 13 songs on CD, playing time 37:52 on Audio CD.
Track 1, start time 00:02:32
Track 2, start time 02:58:60
Track 3, start time 05:27:55
Track 4, start time 08:25:27
Track 5, start time 11:36:02
Track 6, start time 14:41:42
Track 7, start time 17:29:22
Track 8, start time 20:01:00
Track 9, start time 23:28:72
Track 10, start time 26:57:50
Track 11, start time 29:06:60
Track 12, start time 32:20:50
Track 13, start time 34:32:15
Check the website of your computer or drive manufacturer to verify that you have the latest firmware for your CD / DVD drive.
Audio CD reading succeeded.
Thanks.hi Robert!
I am using Roxio Easy Media Creator 7. (version 7.1.1.189 to be precise). I have no other CD burning software but I do have an Iomega external hard drive connected USP2. The software that comes with that is Iomega Automatic Backup v3.2.
no, i can't find anything relevant to do with conflicts with those packages. I'm not sure it's worth trying to uninstall 7.1 just to see what happens. (given that it's actually
b working
at the moment.)
curses. okay, at this point in time, all i can suggest is to start wading through our sea of documentation on burning problems. i believe you've already seen some of this, so apologies in advance:
b noir, "error codes" #4, 08:56am Aug 25, 2005
and then it's into the holding pattern ... keep checking the links to Apple docs, because they get updated. keep refreshing the thread with a post every now and then, in case we've been able to accumulate some more relevant working wisdom on the forums.
sorry i couldn't be of more help.
love, b
Maybe you are looking for
-
Type UI in CS6 in Surface Pro 3 is too small. Adobe needs to isuue a fix for CS6.
I don't need to upgrade CS6 for any photography reason. Adobe should make CS6 UI readable fro surface pro 3 users. They have a fix for later versions. Why not make it available in other earlier versions of photoshop. This is not a question of add
-
Remove xml element using JS[CS3]
Hi, I have an xml structure where i want to remove some paritcular element named "extlink". I do have one script with me but it doesn't wipe out all specific xml element from structure. var myDoc = app.activeDocument; var foundtext = 0 Query_Remove (
-
HTTP 500 Internal Server Error with Large Attachment in SOAP Scenario
Hi, we have implemented SOAP - XI - SOAP Scenario in our landscape (Sap Neatweaver Process Integration 7.1) . One of the functionality of this scenario is the Upload of Documents to External Web Service through standard SOAP Attachment. If we try to
-
My old MacBook (white clunky one) suddenly began to only print in black and white. I changed printers, changed ink, ran the alignment, etc. Nothing converted the printing back to color. Now I have a brand new MacBook Pro and it was printing in col
-
FF will not show pictures in Ebay and Amazon BUT OK in IE8
I have winXP pro on 3 machines all the same problem. I can have the same window open in both programmes. IE8 / IE7 shows pictures FF4 says pictures not available Problem with Halfords / Ebay / Amazon