C819G-4G-V-K9 help (no ip address) Cellular0 is up (spoofing), line protocol is up (spoofing)

We recently purchased a C819G-4G-V-K9 for a remote site that has no ISP available.  I can't seem to get this working properly.  I can tell the cell portion is up and working becuase I can send the router a text message and I receive it on the router.  The cell 0 interface however, is not getting a dhcp address.  Below is my configuration:
hostname Router
boot-start-marker
boot system flash:c800-universalk9-mz.SPA.153-3.M.bin
boot-end-marker
aqm-register-fnf
no aaa new-model
memory-size iomem 10
ip cef
no ipv6 cef
multilink bundle-name authenticated
chat-script lte "" "AT!CALL1" TIMEOUT 60 "OK"
license udi pid C819G-4G-V-K9 sn FTX180680R8
vtp domain MobileCell
vtp mode transparent
controller Cellular 0
interface Cellular0
 ip address negotiated previous
 ip nat outside
 ip virtual-reassembly in
 encapsulation slip
 dialer in-band
 dialer string lte
 dialer-group 1
 async mode interactive
interface FastEthernet0
 no ip address
interface FastEthernet1
 no ip address
interface FastEthernet2
 no ip address
interface FastEthernet3
 no ip address
interface GigabitEthernet0
 no ip address
 shutdown
 duplex auto
 speed auto
interface Serial0
 no ip address
 shutdown
 clock rate 2000000
interface Vlan1
 ip address 192.168.0.1 255.255.255.0
 ip nat inside
 ip virtual-reassembly in
ip forward-protocol nd
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Cellular0 overload
ip route 0.0.0.0 0.0.0.0 Cellular0
dialer-list 1 protocol ip list 1
access-list 1 permit any
control-plane
mgcp behavior rsip-range tgcp-only
mgcp behavior comedia-role none
mgcp behavior comedia-check-media-src disable
mgcp behavior comedia-sdp-force disable
mgcp profile default
line con 0
 script dialer lte
 no modem enable
line aux 0
 script dialer lte
 modem InOut
 no exec
line 2
 no activation-character
 no exec
 transport preferred none
 transport input all
 stopbits 1
line 3
 script dialer lte
 modem InOut
 no exec
line vty 0 4
 login
 transport input all
scheduler allocate 20000 1000
end
Cellular0 is up (spoofing), line protocol is up (spoofing)
  Hardware is 4G WWAN Modem - Verizon Multimode LTE/eHRPD/EVDO RevA/Rev0/1xRTT
  Internet address will be assigned dynamically by the network
  MTU 1500 bytes, BW 9 Kbit/sec, DLY 100000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation SLIP, loopback not set
  Keepalive not supported
  Last input never, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue: 0/10 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     0 packets input, 0 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 packets output, 0 bytes, 0 underruns
     0 output errors, 0 collisions, 0 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
     DCD=down  DSR=down  DTR=up  RTS=up  CTS=up
Router#sh ip int bri
Interface                  IP-Address      OK? Method Status                Protocol
Cellular0                  unassigned      YES manual up                    up
FastEthernet0              unassigned      YES unset  down                  down

Not sure if you solved your problem yet, but my Cell0 has a few extra lines. I also have a static IP, so it might not be exactly the same as yours.
interface Cellular0
ip address negotiated
no ip unreachables
ip nat outside
ip virtual-reassembly in
encapsulation slip
load-interval 30
dialer in-band
dialer idle-timeout 0
dialer string lte
dialer watch-group 1
async mode interactive
routing dynamic
ip sla auto discovery
access-list 100 permit ip any any
dialer watch-list 1 ip 5.6.7.8 0.0.0.0
dialer watch-list 1 delay route-check initial 60
dialer watch-list 1 delay connect 1
dialer-list 1 protocol ip permit
Cellular0 is up, line protocol is up
  Hardware is 4G WWAN Modem - Verizon Multimode LTE/eHRPD/EVDO RevA/Rev0/1xRTT
  Internet address is xxx.xxx.xxx.xxx/32
  MTU 1500 bytes, BW 50000 Kbit/sec, DLY 100000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation SLIP, loopback not set
  Keepalive not supported
  Last input 00:00:00, output never, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 264
  Queueing strategy: fifo
  Output queue: 0/10 (size/max)
  30 second input rate 11000 bits/sec, 16 packets/sec
  30 second output rate 11000 bits/sec, 16 packets/sec
     1242186 packets input, 660512785 bytes, 0 no buffer
     Received 0 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     1164618 packets output, 233386561 bytes, 0 underruns
     0 output errors, 0 collisions, 2 interface resets
     0 unknown protocol drops
     0 output buffer failures, 0 output buffers swapped out
     0 carrier transitions
     DCD=up  DSR=up  DTR=up  RTS=up  CTS=up

Similar Messages

  • Can someone please help? my address bar is missing. All i have in its place is a grayed out tab that will not allow me enter a URL.

    can someone please help? my address bar is missing. All i have in its place is a grayed out tab that will not allow me enter a URL.

    What browser?
    Is this a Mac Pro?

  • How do I fix this error message, The address wasn't understood Firefox doesn't know how to open this address, because one of the following protocols (connectag

    We have a new computer and I cannot get my garmin running watch to sync with mozilla. The error message that I keep getting is"The address wasn't understood
    Firefox doesn't know how to open this address, because one of the following protocols (connectagent) isn't associated with any program or is not allowed in this context.
    You might need to install other software to open this address."
    Help please

    This is for a special URL that starts with
    connectagent://
    instead of with
    http://
    is that right?
    Two thoughts:
    (1) Could you try changing a setting for your Garmin plugin. Here's what I mean:
    Open the Add-ons page using either:
    * Ctrl+Shift+a
    * orange Firefox button (or Tools menu) > Add-ons
    In the left column, click Plugins.
    Find your Garmin plugin change "Ask to Activate" to "Always Activate".
    Your system information seems to list two different versions of a similarly named plugin. I'm not sure whether that is causing a problem.
    (2) Does Garmin's documentation specify any extra steps to set up Firefox, other than installing its add-ons?

  • -5002 Address is empty [OCRD.CardCode][line: 0]

    i upgraded to PL 36
    i have a JAVA code the inserts BP.
    When it tryes to insert a NEW BP, it gets this error:
    -5002 Address is empty OCRD.CardCode line: 0
    Everything else works fine, such as inserting documents.
    If i supress the BPAdresses part, it inserts the BP.
    This is the part of the code i have to supress:
                    IBusinessPartners ib = SBOCOMUtil.newBusinessPartners(company);
                    ib.getAddresses().add();
                    ib.getAddresses().setAddressType(SBOCOMConstants.BoAddressType_bo_BillTo);
                    ib.getAddresses().setAddressName("BillTo");
                    ib.setBilltoDefault("BillTo");
                    ib.getAddresses().setStreet(bp.getCobEndereco());
                    ib.getAddresses().setCity(bp.getCobCidade());
                    ib.getAddresses().setZipCode(bp.getCobCep());
                    ib.getAddresses().setState(bp.getCobEstado());
                    ib.getAddresses().setCountry(bp.getCobPais());
                    ib.getAddresses().setBlock(bp.getCobBairro());
                    ib.getAddresses().setBuildingFloorRoom(bp.getCobComplemento()); 
                    ib.getAddresses().add();
                    ib.getAddresses().setAddressType(SBOCOMConstants.BoAddressType_bo_ShipTo);
                    ib.getAddresses().setAddressName("ShipTo");
                    ib.getAddresses().setStreet(bp.getEntEndereco());
                    ib.getAddresses().setCity(bp.getEntCidade());
                    ib.getAddresses().setZipCode(bp.getEntCep());
                    ib.getAddresses().setState(bp.getEntEstado());
                    ib.getAddresses().setCountry(bp.getEntPais());
                    ib.getAddresses().setBlock(bp.getEntBairro());
                    ib.getAddresses().setBuildingFloorRoom(bp.getEntComplemento());
                    ib.setShipToDefault("ShipTo");
    Any Idea ?
    Anything is welcome
    Tks
    Elcio

    hi elcio,
    i recommend you
    1.) to remove the first
    ib.getAddresses().add();
    because the first line is always there.
    2.) to use SetCurrentLine(0) for the first address and
    after .add do SetCurrentLine(1)
    because you're code writes always in the same address line !
    i hope it helps you
    regards
    David

  • Firefox doesn't know how to open this address, because one of the following protocols (itms-service) isn't associated with any program or is not allowed in this

    Firefox doesn't know how to open this address, because one of the following protocols (itms-services) isn't associated with any program or is not allowed in this context.
    You might need to install other software to open this address."
    tried to fix in about:config but itms-services not foundn; also tried to fix using network.protocol-handler.external.foo but that wasn't listed either
    trying to download an app related to a rewards gift card
    firefox and os versions are up to date on MacBook Air

    Hello!
    Would you please provide the link you were trying to visit?
    Also, you may want to post this question to the [https://support.mozilla.org/en-US/questions/new/desktop Firefox for Desktop Support Forum] . The Mozilla Support volunteers there may be able to better assist you.
    I hope we can help you solve your problem.

  • Same client's address for DDR and Dedicated Line

    I need a help with client's access and routing.
    On my side there is a 3845 router with Async module.
    Clients are of 2 types: dial-up clients and dedicated line clients. All them are authenticated on Radius (chap).
    Dial-up client has a computer, they dial on Group-Async (ip unnumbered GigabitEthernet0/0) and receive ip address from pool, configured on cisco (not on Radius). Thats' work perfect.
    Now about leased (dedicated) line clients. They access from cisco (mostly 2610).
    On my side they have configured ip on LL interface and static routing to that ip.
    If this LL connection is broken, they have DDR access (call from their cisco to my Group-Async interface, same as for dial-up_only users).
    What I need is to set one (only) ip address to clients with leased line access thus, that it would work for DDR-connection as well as for LL connection.
    What I tried and it was successfull is:
    interface Async1/0
    description DDR
    ip unnumbered GigabitEthernet0/0
    encapsulation ppp
    async mode dedicated
    ppp authentication chap
    interface Async1/5
    description LL
    ip address 192.168.1.134 255.255.255.252
    encapsulation ppp
    async mode dedicated
    no peer default ip address
    In this case I could ping 192.168.1.133 in both LL and DDR connection.
    But if only I configure Async1/0 as a member of Group-Async0, I cannot ping 192.168.1.133 (client's side), interface comes to up though.
    interface Group-Async0
    ip unnumbered GigabitEthernet0/0
    encapsulation ppp
    async mode dedicated
    peer default ip address pool POOL1
    ppp authentication chap
    group-range 1/0 1/1
    ip local pool POOL1 192.168.1.1 192.168.1.11
    Because cisco3845 give to client ip from pool:
    *Apr 23 13:22:09.201: As1/0 IPCP: I CONFREQ [REQsent] id 42 len 10
    *Apr 23 13:22:09.201: As1/0 IPCP: Address 192.168.1.133 (0x0306C0A80185)
    *Apr 23 13:22:09.201: As1/0 IPCP: O CONFNAK [REQsent] id 42 len 10
    *Apr 23 13:22:09.201: As1/0 IPCP: Address 192.168.1.1 (0x0306C0A80101)
    *Apr 23 13:22:09.201: As1/0 IPCP: I CONFNAK [REQsent] id 1 len 10
    *Apr 23 13:22:09.201: As1/0 IPCP: Address 192.168.1.134 (0x0306C0A80186)
    *Apr 23 13:22:09.201: As1/0 IPCP: O CONFREQ [REQsent] id 2 len 4
    *Apr 23 13:22:09.301: As1/0 IPCP: I CONFREQ [REQsent] id 43 len 4
    *Apr 23 13:22:09.301: As1/0 IPCP: O CONFACK [REQsent] id 43 len 4
    *Apr 23 13:22:09.309: As1/0 IPCP: I CONFACK [ACKsent] id 2 len 4
    *Apr 23 13:22:09.309: As1/0 IPCP: State is Open
    *Apr 23 13:22:09.309: As1/0 IPCP: Install route to 192.168.1.1
    *Apr 23 13:22:10.077: %LINEPROTO-5-UPDOWN: Line protocol on Interface Async1/0, changed state to up
    One important thing is that I need to configure ip addressing for client without involving RADIUS (it will only check username and password).
    Or explain me someone that its impossible and stop my sufferings...

    I cannot agree more with your comments! What a way to frustrate your customers!
    I have been having an issue with iCloud on Mac where it kept asking me for my password and sometimes would, sometimes would not continue to access my iCloud mail. Today it just refused to connect to iCloud mail.
    I looked in the Mail, Contacts and Calendars in my MacBook Pro settings and discovered that 2 iCloud accounts were present. One with my original Apple ID (a gmail address) and a second with my new iCloud email ( an @me.com address). Having deleted the second account, using the new @me.com address everything is working fine.
    So from my viewpoint when I moved over to iCloud I was asked to sign in with my Apple ID (the gmail address) then to create an @me.com address. However, as far as I can see all sign ins to the new @me.com account on Macbook, iPhone and iPad need to be done through the old Apple ID (the gmail address). Is that confusing and just plain crazy???
    Further, after creating the new @me.com address I soon found out that this is apparently now forever bound to my old Apple ID and cannot be changed. I mean why can't I delete the iCloud account and start anew with a different @me.com address??? Also, as everybody using iCloud must create an @me.com address why on earth can I not get rid of my old gmail address and have my entire Apple ID accessed through the new @me.com address? Creating a whole new Apple ID will not solve this as we are unable to transfer purchases between accounts.
    Apple products are great IMHO, but they do seem to not think things through in a very big way sometimes......

  • Help me in Converting textarea msg to single line string

    Please help me in converting the textarea message with line breaks in to single line string. because i shud pass that to the Javascript which doesnot accept line breaks.
    <%
    StringBuffer text = new StringBuffer(request.getParameter("textarea1"));
    int loc = (new String(text)).indexOf('\n');
    while(loc > 0){
    text.replace(loc, loc+1, "<BR>");
    loc = (new String(text)).indexOf('\n');
    out.println(text);
    %>

    Hi,
    i did not understood your problem. javascript supports \n character processing. so you should not get any error. Do one thing write a javascript function, that replaces all \n with "". this will solve your problem
    funciton replaceNewLine(StringValue) {
    StringValue.replace('\n','') (check replace() syntax once)
    have fun!!
    raj

  • Help needed regarding 'Address Text' in Smartforms

    hi guys,
    To display the address text in Smartforms, we include an 'Address' component and provide the respective address number to it. I just want to know which is the table where the complete address text corresponding to the address number is saved. I have checked the 'ADRC' & 'ADRCT' tables but in vain. Help me out.
    With regards,
    Sandeep Panja.

    Hi Panja,
                 In smartform u have to pass the address no and it's give the full address by FM ADDRESS_INTO_PRINTFORM .plz check this fm and for address check the master table like vendor the table is LFA1 to get the address for it
    tarak

  • Please help external IP address and CCTV

    Hi all,
    I am really struggling to set up my router etc to try and get my Cctv camera to be able to be viewed over a 3G iphone app or another network. I can view the camera over my iphone, iPad etc as long as I am connected to my home network as soon as I lose that I can view the camera, have googled etc and it is saying need to port forward and set up external IP address, in all honesty I have a clue what this is, how to do and getting a little frustrated blindly typing things in, I have a home hub 5 please help some one.
    Thanks
    Si

    There is an additional help page on this link.
    CCTV and IP cameras - port forwarding
    Which IP camera do you have?
    There are some useful help pages here, for BT Broadband customers only, on my personal website.
    BT Broadband customers - help with broadband, WiFi, networking, e-mail and phones.

  • Incorrect search help for Delivery address in SRM User Settings

    Hi experts,
    We use SRM 7.0. When i want to change Users Attribute Delivery address (in SRM User Settings) and call search help for this, than  i get list with 3  identical  addresses.
    For example:
    Value                          Label
    111                         usa/Ny/1
    111                         usa/Ny/1
    111                         usa/Ny/1
    222                         usa/Sf/2
    222                         usa/Sf/2
    222                         usa/Sf/2
    333                         france/P/3
    333                         france/P/3
    333                         france/P/3
    How can I delete undue entries?
    Thanks a lot

    Hi
    Are all adreess numbers Unique ?
    every ship to address has unique . can you check data base level ?
    Muthu

  • Help required - mac address table, virtual pc/ip addressing issue

    Hi, hope someone out there can help?
    This is the scenario
    SW1 (WS-C2960G-48TC-L) port gig0/1 has a PC connected to it with ip address 10.182.8.6 and a Virtual IP address 10.182.8.107
    SW2 (WS-C2960-24TT-L)  port gig 0/1 has a PC connected to it with ip address 10.182.8.106
    The system is designed so that if there is an issue with the PC connected to SW1, the PC on SW2 will take over the Virtual IP address and continue working.
    We have a couple of other PC's in different subnets to the above PC's that use the Virtual IP (VIP) address to communicate with the PC that is 'on line'.
    Unfortunately, the vendors software doesn't currently gratuitously refresh the arp to advertise the change of mac address for the VIP.
    Is there anyway we can get the 2 dcnsw to 'refresh' on a regular time period to capture when the VIP changes to the other PC?

    Hi Stephen
    Without meaning to sound rude, the software which uses a VIP is not very well designed if it is not capable of sending a Gratuitous ARP one the Active one fails.
    The default ARP cache timeout is 4 hours so an ARP entry will remain in the table and once the timeout is up, the switch will send an ARP to check if the device is still alive and if not, remove the entry from the table.
    You could look at reducing the ARP timeout on a per port basis:
    #interface gi1/0/1
    #arp timeout 60
    This will change the ARP cache timeout to 60 seconds for that port but having not used this before, I am not 100% this will address your issue. I would not advise trying to change the global ARP cache timeout for a production switch as this will increase ARP traffic and could cause problems if reduced to a small value.

  • Help!! Address Book and iCal don't open

    When I try to open Address Book or iCal they won't open. I've reinstalled the latest OS update (10.4.10) and still they won't open. I urgently need to access some of the details in my address book - does anybody have idea why they won't open?
    Any help at all will be massively appreciated. Thanks.
    One more thing - I had a faulty ram chip replaced a couple of weeks ago - could this have had any bearing on this situation? They worked fine prior to this.

    This is in response to the iCal crash problems. I'm posting this in several different forums, so please pardon the generalized nature of the response.
    System:
    *Hardware:
    **Mac Book Pro,
    **1.83GHz Intel Core Duo
    **1.5 GB 667 MHz DDR2 SDRAM
    **60 GB hard disk
    *Software:
    **Mac OS X ver 10.4.10
    Symptom: iCal suddenly started crashing on launch. Sometimes the calendar would appear and then close before the individual calendars on the side pain would populate. Othertimes it would crash before. Crash reports were almost always generated.
    Thanks to the guys at the Oakridge Mall (San Jose, CA) Apple Store, I was given an overview of how to move folders in the ~/Library folder to the desk top, launch iCal, see if that works. We tried the Preferences folder first, that didn't work. I figured it would take a while to narrow it down, so I took my Mac Book home to continue work on it, and I narrowed it down to the Caches folder.
    Procedure: (I did all this through the Finder).
    1) Move ~/Library/Caches to the desktop.
    2) Start iCal. A new Caches folder should be created, and iCal should spend a little time setting up, then iCal should work with all previously existing calendars present and up to date (at this point, I can't tell that I've lost anything at all).
    3) Rename the newly created Caches folder to "Caches-New" (or otherwise save this folder).
    4) Move the Caches folder which was saved to the desktop back to the ~/Library folder.
    5) Copy the following from "Caches-New" to the just-restored Caches folder:
    5a) Copy Caches-New/com.apple.iCal to ~/Library/Caches (you will be replacing the old version of this file)
    5b) Copy Caches-New/Metadata/iCal to ~/Library/Caches/Metadata (you will be replacing the old version of this folder).
    I suspect the problem was with the contents of the Metadata folder.
    Hope this helps.
    (Similar steps might be used for the address book. I noticed that when the new Cache folder was created, there were address book components as well after I opened iCal).
    -ktb
    karl ^*AT*^ tunnell-braun.com
    (expect a spam-filter request for verification)

  • Help moving email addresses from BT dialup to BT b...

    Hello,
    I am currently helping a non technical relative of mine who is getting BT Broadband and currently uses BT dialup internet and I am trying to be prepared in advance of setting it up. They have placed the order for broadband and been given a new btinternet.com email address for the account. We are now waiting for a password to be sent and for the homehub to arrive.
    My questions concerns their current dialup email accounts. They have two btinternet.com email addresses which are primary BT Yahoo accounts (I think that's the right terminology but I'm on a bit of a learning curve here myself). There are no sub accounts involved with this. BT told my relative that it is possible for her to move these email addresses over to the broadband account but did not explain how this is done. We want them linked to the broadband account so they don't get flagged as inactive when the dial up is no longer used.
    Questions -
    1. Do we set up the dial up addresses as sub accounts on the new broadband account or is it done some other way? Will we be able to do this? Because they are existing primary accounts I can imagine it not being allowed because the email addresses are already in use.
    3. Over the years my relative has used both the btinternet.com and btopenworld.com versions of the addresees. I understand these are in fact treated as the same address. Is that correct or do we need to move both versions to the broadband account.
    Thank you for any help you can provide.

    I don't know if this is relevant but I have just moved from BT broadband to BT Infinity and my e-mail address has remained the same.  Whether this will apply moving from dial-up to broadband I can't say.but as the other poster said, try contacting the helpdesk.
    wedding
    Mistakes and embarrasing goofs in e-mails are only discovered when you've sent them!

  • What is the OBIEE help group email address?

    Hi,
    I need help from obiee team for one question,but I can not find the email address in the forums.(the email address who answered some one's question is private)
    There is a image in my question which can not be showed in the forums,so I want to ask the question by email.
    thanks in advance
    Jinbo

    thanks
    I have got the email address.
    thanks
    Jinbo

  • Help with restoring Address Book from Time Machine

    Problem: I really, really need to retrieve someone's number. I know it'll be in an old version of my Address Book. I can see when I open time Machine that my address book is backed up, but no matter the date I go to, it says the Address Book was last modified in 2012! I know for a fact I've updated (and backed up) the Address Book many times since then.
    Whenever I try to restore the Address Book, I do Time Machine > Applications > Address Book > 'restore'. But whenever I do this, the mac refuses to open the restored Address Book because it's 'required by mac OS X'.
    I don't understand.
    Please, how on earth do I dredge my Address Book from the depths of Time Machine?
    Please help!
    M

    Hello mb9236,
    Thank you for the details of the issue you are experiencing with restoring a contact from Time Machine. 
    It sounds like you are trying to restore the Address Book application.  The Address Book application is just the application and does not include the content in Address Book. 
    Instead, you will want to open Address Book and then launch Time Machine and restore your contacts from there.  Use the steps below to restore your contacts form a previous date (in step one instead of opening Mail or Finder, be sure you have Address Book open and in focus):
    If you use Time Machine to back up your computer, you can easily bring back one or more items you’ve lost, or recover older versions of files you’ve changed.
    Open a window for the item you want to restore. For example, if you accidentally deleted a file from your Documents folder, open the Documents folder. If you want to recover an email message, open your inbox in Mail.
    If you’re missing an item from the desktop, you don’t need to open a window.
    Click the Time Machine icon in the Dock, or open the Time Machine menu in the menu bar and choose Enter Time Machine. If you back up to a Time Capsule or other network disk, a message briefly appears while Time Machine connects your computer to the backup disk.
    Use the arrows or the timeline along the right side of your screen to browse through all the snapshots and backups Time Machine created. Gray tick marks on the timeline represent snapshots stored on your internal drive (portable computers only). Pink tick marks represent backups stored on your backup disk.
    If you need more information about an item, double-click to preview it. The windows in Time Machine behave just like Finder windows, so you can open folders, click items in the sidebar, and use the search field in the upper-right corner of the window.
    When you find the item you want to restore, select it, and then click Restore. You can restore individual items, multiple items, folders, or your entire hard disk. The restored item is returned to its original location. For example, if the item was found in the Documents folder, it is returned to the Documents folder. Time Machine may ask if you want to re-create one or more folders in order to return a restored item to its original location.
    If an item you restore has the same name as another item on your computer, you’re asked if you want to keep the current item, the restored item, or both.
    You can use Time Machine from within many applications. For example, you can open Address Book and then click the Time Machine icon in the Dock to recover contacts you may have accidentally deleted, or open iPhoto and then click the Time Machine icon in the Dock to view past versions of your iPhoto albums.
    OS X Lion: Restore items backed up with Time Machine
    https://support.apple.com/kb/PH4256
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

Maybe you are looking for

  • How do I load MS office 2011 with a product key only

    Trying to use a product key (media-less) download of MS Office 2011 for my new MacBook Pro.  I thought you had to have a trial version installed on your computer before you could load the full version (at least that's the way it worked on PC).  How c

  • Topic properties

    I am having a real problem with topic properties not cooperating. For some reason, RoboHelp insists on making some of my topic titles lowercase. For example - the title Copyright. It keeps changing the "c" to lowercase. Also, I want the filenames to

  • How to install Quicktime WITHOUT iTunes?

    It seems that there isn't a Quicktime installation kit, just an "iTunes with Quicktime" kit. That can't be right. I don't want to install Apple bloatware that I'm never going to use and would just uninstall right away just to get a simple video playe

  • LabVIEW classes not fully compatiable with polymorphic VI's

    I'm just working on a set of fully object orientated drivers for a .NET assembly provided by a 3rd party that we have to integrate into our existing code. To provide base command functionality into the .NET assembly I am using polymorphic vi's (an ex

  • My HP Photosmart 3210 no longer prints in color. Why?

    A friend messed around with my Photosmart 3210 and it no longer prints in color.  It also operates at too high a speed.  I have looked at all the settings I know how to look at and have had no luck finding a cure.  What should I do?