Calculate coherence for a series of Impacts

Calculating coherence has been discussed several times - including this knowledge base article and community example. But I'm still missing something.
How can I calculate the coherence so it updates after each hit (right now it's always 1)?
On a related note, I'm assuming the Y signals in the FRF(Mag-Phase) are the response and the X signals are the stimulus...Transfer Function.vi explicitly states Response and Stimulus for its inputs, but FRF(Mag-Phase) doesn't.
I attached an abridged version of what I've attemped.
Andrew
Attachments:
CalcCoherences.vi ‏18 KB

Check this example:
http://zone.ni.com/devzone/cda/epd/p/id/5810
You will see that to measure coherence you need to input the same size array or waveform. In your VI, you are sending your input through a shift register and augmenting the size of your array.
National Instruments
Applications Engineer

Similar Messages

Drill Down for Multiple Series in a Line Chart

Hello,
I seem to have a problem with the drill-down functionality in a line chart that has multiple series.
I have a line chart that displays the readings of a patient over a period of 1 month. For each day, there is the glucose level reading, blood pressure reading, etc... So, each reading is a different series in my line chart graph.
The basic requirement is: With a mouse over event on the chart, I am willing to display all the data that belongs to that day. The data will be displayed at the bottom of the screen in a small panel. It is very simple to do it when the line chart has only 1 series:
i) Enable drill down.
ii) Choose 'Row' as insertion type.
iii) Fill out the destination field.
iv) Make sure your labels (at the bottom of the screen) get the data from the destination cell.
When there is more than one series, it becomes very difficult. XCelsius will not let me use the same destination cells for different series. So, I will have to use other destination cells. In that case, I will not know on which day is the user on. Is there any way to achieve this functionality?
Let me know if you need further information.

This is certainly possible, but there's a bit of a trick to it (and really hard to explain without screenshots!). There's two halves to it:
1. Write the date that has been selected to a cell (for each series).
2. Write the name of the series that was clicked to some cell (this is the property 'Series Name Destination').
So let's say your three series are Glucose, Blood Pressure and Temp. Have those series names in B1,C1,D1 (with your dates down in column A). Insert a row below the series names (2:2), and then set up your insertion type for the chart as 'row'. The source data (for all three series) should be your list of dates in column a. The insertion cells for the three series will be, in order, B2,C2,D2. Now, depending on which point is clicked in the chart, the selected day will be inserted into one of those three cells. Completely useless unless you know which series was clicked.
So you need to insert the name of the series that was clicked ('Series Name Destination') into the spreadsheet, let's say in F1. The rest is just Excel formulas. The logic is, you can now tell what series was clicked, and go and look up the date that was inserted for that series, then go and look up the row that corresponds to that date. So to get the date that was just clicked, your formula (in F2) would be =HLOOKUP(F1,B1:D2,2,0).
Then a VLOOKUP will get the results from that row of data. For example, if I inserted another row at row 3 (to show my 'result' values) the formula in B3 would be =VLOOKUP($F$2,$A$4:$D$13,2,0).
I hope that makes sense.

Is there a way to change the default colors for data series in charts?

I have tried to find settings for data series colors in the various CSS files but have not found any.

Did you try:
OracleBI/web/app/res/s_.../popbin/
EX:
line.pcxml Look for <SeriesDefinition ...
we modified the line width and a few other things. You'll have to modify all the pcxml files for all the chart types you want to customize.

Show DataTips for each series

Is there a way to customize the DataTips for each series in a
chart? I have a column chart that has a line series in it. The
columns display actual data, but the line shows an average.
Currently the datatips are set to show the column chart values,
even when a user hovers over a line chart datatip. Is there any way
to have the datatips for the lineseries display the lineseries
data?
I know I could create a DataTipFormatter that included both
the column data and the line data at the same time, but I would
like them separate.

Adobe Newsbot hopes that the following resources helps you.
NewsBot is experimental and any feedback (reply to this post) on
its utility will be appreciated:
L (Flex 3):
The LineChart control represents a data series as points
connected by a continuous .... whose contents are highlighted when
a user moves the mouse over it.
Link:
http://livedocs.adobe.com/flex/3/langref/all-index-L.html
Is it possible to use data labels with line chart? - Flex
India:
Feb 27, 2008 ... I want to create a line chart which shows
all the labels, regardless of the mouse pointer.
showAllDataTips=true works but the result is
Link:
http://groups.google.com/group/flex_india/browse_thread/thread/709c9651ad7c9062
mx.charts.LineChart (Flex 2.0.1 Language Reference):
Specifies the distance, in pixels, that Flex considers a data
point to be under the mouse pointer when the mouse moves around a
chart.
Link:
http://livedocs.adobe.com/flex/201/langref/mx/charts/LineChart.html
Print Page - Disable datatip but keep mouse event on line
chart:
Flex and ActionScript 3.0 => Flex Charting => Topic
started by: Sablotron on 29 July 2008, ... Title: Disable datatip
but keep mouse event on line chart
Link:
http://www.flexdeveloper.eu/forums/index.php?action=printpage;topic=895.0
[#FLEXDMV-1683] dataTipFunction for LineChart is not executed
when:
Mar 12, 2008 ... Set dataProvider for LineChart with one
datapoint 3. Set a dataTipFunction for the LineChart Actual
Results: Datatip does not show on mouse
Link:
http://bugs.adobe.com/jira/browse/FLEXDMV-1683
Disable datatip but keep mouse event on line chart |
flexdeveloper:
Aug 6, 2008 ... Disable datatip but keep mouse event on line
chart, help forums for developers working with ActionScript 3.0,
Flex 3, Flash CS3.0, and AIR.
Link:
http://www.flexdeveloper.eu/forums/index.php?topic=895.msg2716
Disclaimer: This response is generated automatically by the
Adobe NewsBot based on Adobe
Community
Engine.

Unable to calculate depreciation for 2008

Hi friends,
I would like to calculate depreciation for the fiscal year 2008.This is client requirement.He calculated depreciation 2008 and period-1.When he tried to execute depreciation for 2nd period he is getting problem
"Not all the documents in the last posting run were posted"
     Message no. AA 729
Diagnosis
     The posting session created in the last posting run was not completely
     processed. The last posting run was in fiscal year 2008, period 001,
     current number 01. A new posting run is only possible once the posting
     session has been processed completely.
Procedure
     Process the session created by the last posting run again. If this
     session no longer exists, you can create a new posting session that
     contains the missing posting documents. This function is found in the
     menu under "Recreate session." However, it is essential that no changes
     have been made in the meantime to the Customizing definition of the
     document number range.
After that i have analysed this situation. When i check TABA Table system showing document numbers are updated but document posted indicator X is not showing.
I have also checked FI documents it is not showing.
I have tried to recreate session but my problem has not been solved.
I found one SAP Note : 926062 - Errors AU265 or AA729 during RAJABS00 OR RABUCH00.It is the consulting issue.
Can anybody help me out resolve this situation and how can calculate depreciation ?
Thanks in Advance .

Dear Anji,
We had a similar situation. It was resolved for the period 1 and the once again system showed the same error while processing for period 3, same error 'Not all the documents.....
Procedure followed is this.
T.Code : AFBD for recreation of the session.
T.Code : SM37 the job wil show as finished and display will show as waiting.
but in spool display the log's last line will inform us to proces the session wainting in SM35
T.Code : SM35 process it by checking on Display Errors Only, and enter the appropriate transaction type (220)
After the above, we found the TABA table document number ranges are matching with FB03.
and the posting indicator is also updated.
Warm Regards
KV

All music and other things on itouch GONE except for one series of podcasts

I need help!
My computer is low on memory, but I didn't think that would mess up me connecting my iPod touch to my computer. After connecting it, I did not look at my library, but later when I went to listen to something ALL my music, playlists, proof of purchases, were gone, except for one series of podcasts. I decided to connect my iPod to the computer again to see if I could igure out what was going on, and I got a thing that said I was using the iPod on a different account! confused it asked me if I wanted to get my purchased music switched over, so my sister suggested doing that, and so they are back on Itunes, but my computer is having problems because of low memory, so I haven't been able to get it to sync. (I have not tried a lot yet)
can anyone help me? All my apps are there. It's just the music.

When it asked if I wanted to transfer or erase or sync, I chose to transfer purchases, and ALL my music, including not purchased (CD's I had put on there) came back. ALL my music is back! Problem solved!

Function returning SQL query for mutiple series in a chart

Hi,
I would like to know if there is a way to specify a single PL/SQL function returning the queries for multiple series in a 2D Line Flash Chart. I have multiple series in my chart that has different values in the where clause. I can write a PL/SQL function that can return all these queries in one shot. Is there anyway that I can specify this function as returning the queries for all the series in the chart?
As an example, assume that I am using the following three queries for the series in my chart:
select deptno, count(*) from emp where deptno = 10 group by deptno
select deptno, count(*) from emp where deptno = 20 group by deptno
select deptno, count(*) from emp where deptno = 30 group by deptno
I can't write a PL/SQL function that returns a query in the multiple series syntax (SELECT link, label, series_1_value [, series_2_value [, ...]]FROM ...) as I am using an aggregate function and my where clause is different for each series.
Thanks,
Rupesh

Hi Roel,
Thanks for your reply. I am already using an analytical function (RATIO_TO_REPORT(COUNT(*)) OVER () ) in my actual report. My problem is that the query for one series differs from the other only in one where clause. I will be able to dynamically able to generate all the queries for all the series in one pl/sql function. But the chart definition screen does not allow us to define a single function that returns queries for the all the series - possibly seperated by some seperator like S1: select.... S2:select and so on.
Regards,
Rupesh

IN NUMBERS HOW DO YOU FILL IN FOR A SERIES OF NUMBERS OR DATES

In numbers how do you fill in for a series of numbers or dates without doing it manually

You can enter a value in two cells that establishes a pattern, then select the two cells, then click (and hold) on the little circle at the bottom right corner of the selection and drag to fill as needed.
A Number sequence:
A Date sequence:

The problem of creating service for adapter for mq series v8.1

Hi everyone, I have some problem when I try to create service for adapter for mq series using application integration design console. Everything is fine when I define the service but some error shows when I try to test it. The error message is:
-------- Begin level 0 Exception Stack Trace --------
com.bea.wlai.client.ApplicationViewException: Failed to locate deployment information for service ' on ApplicationView 'AppView1'
at weblogic.rmi.internal.ServerRequest.sendReceive(ServerRequest.java:186)
at weblogic.rmi.cluster.ReplicaAwareRemoteRef.invoke(ReplicaAwareRemoteRef.java:290)
at weblogic.rmi.cluster.ReplicaAwareRemoteRef.invoke(ReplicaAwareRemoteRef.java:247)
at __WLAdapter4MQSeries_Prototype_48f240ab.AppView1_6k4mbt_EOImpl_814_WLStub.getRequestDocumentDefinition(Unknown Source)
at com.bea.wlai.client.ApplicationView.getRequestDocumentDefinition(ApplicationView.java:573)
at jsp_servlet.__testrslt._jspService(__testrslt.java:361)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:33)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:1006)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:419)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:315)
at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispatcherImpl.java:638)
at weblogic.servlet.internal.RequestDispatcherImpl.include(RequestDispatcherImpl.java:423)
at weblogic.servlet.jsp.PageContextImpl.include(PageContextImpl.java:154)
at jsp_servlet.__display._jspService(__display.java:659)
at weblogic.servlet.jsp.JspBase.service(JspBase.java:33)
at weblogic.servlet.internal.ServletStubImpl$ServletInvocationAction.run(ServletStubImpl.java:1006)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:419)
at weblogic.servlet.internal.ServletStubImpl.invokeServlet(ServletStubImpl.java:315)
at weblogic.servlet.internal.WebAppServletContext$ServletInvocationAction.run(WebAppServletContext.java:6718)
at weblogic.security.acl.internal.AuthenticatedSubject.doAs(AuthenticatedSubject.java:321)
at weblogic.security.service.SecurityManager.runAs(SecurityManager.java:121)
at weblogic.servlet.internal.WebAppServletContext.invokeServlet(WebAppServletContext.java:3764)
at weblogic.servlet.internal.ServletRequestImpl.execute(ServletRequestImpl.java:2644)
at weblogic.kernel.ExecuteThread.execute(ExecuteThread.java:219)
at weblogic.kernel.ExecuteThread.run(ExecuteThread.java:178)
-------- End level 0 Exception Stack Trace --------
And my request document is:
<?xml version="1.0"?>
<ns0:s1 xmlns:ns0="wlai/AppView1_s1_request">
<Data>123</Data>
</ns0:s1>
The following is the schema for the request document:
<?xml version="1.0" encoding="UTF-8"?>
<xsd:schema elementFormDefault="qualified"
targetNamespace="wlai/AppView1_s1_request"
xmlns="wlai/AppView1_s1_request"
xmlns:xsd="http://www.w3.org/2001/XMLSchema">
<xsd:element name="s1">
<xsd:complexType>
<xsd:sequence>
<xsd:element name="Data"
type="xsd:string"/>
</xsd:sequence>
</xsd:complexType>
</xsd:element>
</xsd:schema>
Anybody got some idea about this problem? Thanks for your help.

Did you check these links ->
http://www.adp-gmbh.ch/ora/admin/creatingdbmanually.html
http://www.dbasupport.com/oracle/ora10g/CreateDBManually.shtml
http://download.oracle.com/docs/cd/B19306_01/server.102/b14231/create.htm#ADMIN002
Regards.
Satyaki De

SCB-68A Reference Label for R series

Cannot find anywhere a working pdf/lisf for SCB-68A for R series devices.
Thanks

Let's try this KnowledgeBase Article:
Where Can I Find NI SCB-68A Quick Reference Labels?
Joey S.
Software Product Manager
National Instruments

Calculate average for some dates

Hi,
I would like to calculate average for some dates. Is there any function module or any process, please provide me.
venkat.

Use this FM HR_HK_DIFF_BT_2_DATES
Example:
DATA: DATE1 type P0001-BEGDA,
DATE2 type P0001-BEGDA,
YEARS type P0347-SCRYY,
MONTHS type P0347-SCRMM,
DAYS type P0347-SCRDD.
DATE1 = '20070331'.
DATE2= '20070101'.
CALL FUNCTION 'HR_HK_DIFF_BT_2_DATES'
EXPORTING
DATE1 = date1
DATE2 = date2
OUTPUT_FORMAT = '03'
IMPORTING
YEARS = years
MONTHS = months
DAYS = days
EXCEPTIONS
INVALID_DATES_SPECIFIED = 1
OTHERS = 2
IF SY-SUBRC 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
Regards,
Joan

TS1424 I have been charged 2x for a series pass. Will apple refund?

I have been charged 2x for a series pass. Will apple refund?

You can try contacting iTunes support via this page and ask : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption

Driver for MM4000 series (motion controller) for labview 6.1 (gpib)

Hello,
I need the instrument driver for a newport motion controller MM4006.
I found the driver for MM4000 series, it could be ok, but I need it for labview 6.1 and not for labview 7 or 8.
Is it possible to find this driver for older version of labview than 7 or 8?
Thanks
Best regards.
Ludovic

Good idea, I'm not sure of the result, but... Here is the zip file (aviable here).
(oups, you were faster ^^)
Message Edité par Mathieu R. le 12-08-2006 05:19 PM
.mrLeft{float:left} .mrInfo{border-left:solid 1px #989898;font-size:x-small;color:#989898}
Mathieu R.
  CTD - Certified TestStand Developer / Développeur TestStand Certifié
  CLAD - Certified LabVIEW Associate Developer
Attachments:
npmm4000.zip ‏419 KB

Alerts for Multi Series Charts

Hi All,
Can we apply alerts for multi series charts?
I am able to set the alerts if i have 1 series where as the alerts are grayed out if i create more than 1 series.
Is this design behaviour??
Is there any work around??
Thanks in advance.
Regards,
Sudharam

Install Xcelsius SP4 (available now).below features are supported among many
1. Combination charts can have alerts for multiple series
[http://everythingxcelsius.com/news/news-alert-xcelsius-2008-service-pack-4-sp4-is-now-available-to-everyone/4030]
Sp4 Download Link:
[SAP Crystal Solutions Downloads ]
Good Luck.

In Primavera Risk Analysis, the MIN. ML, MAX columns is for imput the minimum impact, most likely impact , maximum impact duration of a risk or the remaining duration for MIN, ML and adding remaining duration with maximum impact for MAX?

In Primavera Risk Analysis, the MIN. ML, MAX columns is for imput the minimum impact, most likely impact , maximum impact duration of a risk or the remaining duration for MIN, ML and adding remaining duration with maximum impact for MAX?

You are welcome. I'm glad you got it back up.
(1) You say you did the symbolic link. I will assume this is set correctly; it's very important that it is.
(2) I don't know what you mean by "Been feeding the [email protected] for several weeks now, 700 emails each day at least." After the initial training period, SpamAssassin doesn't learn from mail it has already processed correctly. At this point, you only need to teach SpamAssassin when it is wrong. [email protected] should only be getting spam that is being passed as clean. Likewise, [email protected] should only be getting legitimate mail that is being flagged as junk. You are redirecting mail to both [email protected] and [email protected] ... right? SpamAssassin needs both.
(3) Next, as I said before, you need to implement those "Frontline spam defense for Mac OS X Server." Once you have that done and issue "postfix reload" you can look at your SMTP log in Server Admin and watch as Postfix blocks one piece of junk mail after another. It's kind of cool.
(4) Add some SARE rules:
Visit http://www.rulesemporium.com/rules.htm and download the following rules:
70sareadult.cf
70saregenlsubj0.cf
70sareheader0.cf
70sarehtml0.cf
70sareobfu0.cf
70sareoem.cf
70sarespoof.cf
70sarestocks.cf
70sareunsub.cf
72sare_redirectpost
Visit http://www.rulesemporium.com/other-rules.htm and download the following rules:
backhair.cf
bogus-virus-warnings.cf
chickenpox.cf
weeds.cf
Copy these rules to /etc/mail/spamassassin/
Then stop and restart mail services.
There are other things you can do, and you'll find differing opinions about such things. In general, I think implementing the "Frontline spam defense for Mac OS X Server" and adding the SARE rules will help a lot. Good luck!

Calculate coherence for a series of Impacts

Similar Messages

Maybe you are looking for