Calculating Calculating

When the power adaptor is not in the macbook should say 'calculating' and then give a time left.
More and more, mine just says calculating, and stays this way all the time.
I am noticing other oddnesses with power as well, for instance I can put it too sleep with 50min left and in the morning its dead. Or when waking from sleep it will immediately tell me I am on reserve power but then suddenly decide I have an hour left.
Is this something worth getting checked out?

Here you go:
Battery Information:
Model Information:
Serial Number: 9G91409EG3NYB
Manufacturer: DP
Device name: bq20z951
Pack Lot Code: 0000
PCB Lot Code: 0000
Firmware Version: 002a
Hardware Revision: 0005
Cell Revision: 0100
Charge Information:
Charge remaining (mAh): 563
Fully charged: No
Charging: Yes
Full charge capacity (mAh): 3882
Health Information:
Cycle count: 164
Condition: Normal
Battery Installed: Yes
Amperage (mA): -1136
Voltage (mV): 10950
The concern I see in there is it says 'Charging: Yes'
Well its not charging, no power connected.
Message was edited by: Gary i

Similar Messages

Get the month from a date column with the calculated column

I am trying to get the month from a date field with the help of calculated column. However I get this syntax error whenever I want to submit the formula:
Error
The formula contains a syntax error or is not supported.
the default language of our site is German and [datum, von] is a date field.

Hi,
I have created two columns
Current MM-YY
Calculated (calculation based on other columns)
Today
Date and Time
Current MM-YY is calculated value with formula as
=TEXT(Today,"mmmm")
But the output shows as December instead of May.
I have tried =TEXT([Datum, von];"mmmm") but no help.
I am trying to populated the column automatically with current month..ex: if its May the field should show May, next month it should show June an so on.
Any kind help is grateful.
Regards,
Pradeep

How to display a percentage sign in calculated member column?

Hello all,
in my report I have a calculated member column whose value is determined by follwing value formula:
if CurrentColumnIndex - 2 = 1 then
        If GridValueAt(CurrentRowIndex, CurrentColumnIndex-3, CurrentSummaryIndex) = 0 then
        0
        else
        (GridValueAt(CurrentRowIndex, CurrentColumnIndex-1, CurrentSummaryIndex)/
        GridValueAt(CurrentRowIndex, CurrentColumnIndex-3, CurrentSummaryIndex)) * 100
    else
        If GridValueAt(CurrentRowIndex, CurrentColumnIndex-5, CurrentSummaryIndex) = 0 then
        0
        else
        (GridValueAt(CurrentRowIndex, CurrentColumnIndex-1, CurrentSummaryIndex)/
        GridValueAt(CurrentRowIndex, CurrentColumnIndex-5, CurrentSummaryIndex))*100
Returned is a numeric value and it is being correctly displayed in calculated member column. As the value should represent percentage, I need to display a % sign after every value.
How would I achieve this? I have seen a thread here in the discussion where approach with a formula and DisplayString function is mentioned - but there are no details how this could be achieved....
The crosstab in question looks like this:
Calculated Member is based on "REV_TOTAL" group column.
I also attached the .rpt file (renamed to .txt for upload)
Many thanks in advance,
Marin

Hello Raghavendra,
thanks for the quick reply.
Unfortunately it is not as easy at it seems - calculated member column is not showing in report designer and I can not apply the suggested approach with formatting toolbar...
The column only shows here (right click on table -> "Advanced Calculations" -> "Calculated Member...") and there is no possibility to format it directly:
Any other suggestions?
Many thanks,
Marin

Can I create a calculator like this with jQuery alone?

My knowledge of Javascript is negligible. I was wondering if a calculator like this could be created with jQuery, or if it would require knowledge of writing Javascript?
http://www.sonar6.com/pricing/

Start with jQuery Calculation plugin. Tweak values as required.
http://www.pengoworks.com/workshop/jquery/calculation/calculation.plugin.htm
Nancy O.
Alt-Web Design & Publishing
Web | Graphics | Print | Media Specialists
http://alt-web.com/
http://twitter.com/altweb
http://alt-web.blogspot.com/

Mdx rounding of values included in calculation

Hello Experts
We have a problem with decimals which result in very large figures for some calculations so therefor wan't to add a rounding like this but then we will only round the result, but we need to round the values included in the calculation:
// Calculated in PS
*function fn_INDIPS(%denominator%,%numerator%,%p3%)
iif( (%denominator%,[currencydim].[sek],strToMember(categorydim.properties("PS_INDEX_CAT"))) = 0,Null,round((%numerator%,[currencydim].[sek],strToMember(categorydim.properties("PS_INDEX_CAT"))) / (%denominator%,[currencydim].[sek],strToMember(categorydim.properties("PS_INDEX_CAT"))),4) * %p3%), solve_order = 9
*endfunction
So i think what would solve it would be to add a rounding to the "if devided by 0 then null" or a if OR(<0.0001;>0.0001) but from what i have tried that is not possible. Do you know if it's possible or du you have any other suggestion for how we should get aroudn the problem?
// Calculated in PS
*function fn_INDIPS(%denominator%,%numerator%,%p3%)
iif( (round(%denominator%,[currencydim].[sek],strToMember(categorydim.properties("PS_INDEX_CAT"))),4) = 0,Null,(%numerator%,[currencydim].[sek],strToMember(categorydim.properties("PS_INDEX_CAT"))) / (%denominator%,[currencydim].[sek],strToMember(categorydim.properties("PS_INDEX_CAT"))) * %p3%), solve_order = 9
*endfunction
Best regards
Jonas

Hi Perven,
You can definitely do a round off using the native excel formulas. However, the problem lies with the EVDRE. Whenever an EVDRE template is expanded, all the custom formulas maintained in the expansion range gets overwritten. So, it will be little difficult. One option would be to turn off the expansion for either rows and columns and use the custom functions for you purpose.
Hope this helps.

CR 2011 - calculated member in cross tab

Hello,
I have created a cross tab in my report and added a calculated member. I have created a formula for all my rows because by default the value of the calculated member was "0". Now I wanted to add a new row to my report. The value in the calculated member now is not "0" but empty. How can I access the formula workshop now?
Can anybody help?
Thanks and regards,
Jule

if you right click on the cross-tab > go to Advanced Calculations > Calculated Member > click on the one that you want to edit and press the Edit Value Formula button
cheers,
jamie

Recipe calculator not working, no errors

This is my coding for
my calculator to generate new quantities for a recipe. For some unknown reason, it will not display the new quantities in the second listbox. Any help would be greatly appreciated.
Public Class Form1
    Dim arrsize As Integer =
0
    Dim arrsize1 As Integer =
0
    Dim arrsize2 As Integer =
0
    Dim Ingredients1(2,
arrsize) As String
    Dim Ingredients2(2,
arrsize2) As String
    Dim inglist1 As String = "Ing,
Amount, Unit" & ControlChars.CrLf
    Dim inglist2 As String = "Ing,
Amount, Unit" & ControlChars.CrLf
    Dim calculation As Integer
    Private Sub AddIngButton_Click(sender As System.Object,
e As System.EventArgs)Handles AddIngButton.Click
            Ingredients1(0,
arrsize) = Ing.Text
            Ingredients1(1,
arrsize) = Amount.Text
            Ingredients1(2,
arrsize) = Unit.Text
            inglist1
= Ingredients1(0, arrsize) & ControlChars.Tab
& Ingredients1(1, arrsize) & ControlChars.Tab
& Ingredients1(2, arrsize)
            Ingredients1list.Items.Add(inglist1)
            ReDim Preserve Ingredients1(2,
arrsize)
            Ing.Text
= ""
            Amount.Text
= ""
            Unit.Text
= ""
    Private Sub CalcButton_Click(sender As System.Object,
e As System.EventArgs) HandlesCalcButton.Click
do until arrsize1
= arrsize
                Ingredients2(0,
arrsize1) = Val(Ingredients1(0, arrsize1))
                calculation
= Val(Ingredients1(1, arrsize))
                calculation
= (calculation / OldNumServes.Text) * NewNumServes.Text
                Ingredients2(1,
arrsize1) = calculation
                Ingredients2(2,
arrsize1) = Val(Ingredients1(2, arrsize1))
                inglist2
= Ingredients2(0, arrsize) & ControlChars.Tab
& Ingredients2(1, arrsize) & ControlChars.Tab
& Ingredients2(2, arrsize)
                Ingredients2list.Items.Add(inglist2)
                arrsize1
= arrsize1 + 1
            Loop
    End Sub
End Class

Hi Jack,
I'm afraid that you posted your question on the wrong forum. This forum is dedicated to Project Online microsoft scheduling solution.
Please go there: http://social.technet.microsoft.com/Forums/en-us/home finding the right place for your question.
Cheers.
Guillaume Rouyre - MBA, MCP, MCTS

Could u guys help me with a calculator program

hi
i'm writing a calculator program for my java class and the code ur about to read actually works but when i click on the keypad i don't get any numbers in the display screen, the textfield
Could u guys have a look at it please:
here we go
import javax.swing.* ;
import java.awt.* ;
import java.awt.event.* ;
public class Calculator extends JFrame implements ActionListener {
public boolean firstDigit;
public int temp1 = 0;
public int temp = 0;
public int result = 0;
public String opr = "";
JTextField tf= new JTextField ("",20) ;           //sets the display initially at 0
//tf.setEditable (false) ; this doesn't work
JPanel pan = new JPanel() ;
JButton bclear= new JButton("C") ;
JButton b0= new JButton("0") ;
JButton badd = new JButton("+") ;
JButton bsub = new JButton("-") ;
JButton bmult = new JButton("x");
JButton bdiv = new JButton("/") ;
JButton bpoint= new JButton(".");
JButton bequal = new JButton("=");
public Calculator (String title) // constructor
super(title)     ;
pan.add(tf);
for ( int i=1; i<=3; i++)
JButton butt=new JButton(""+i);
butt.addActionListener(this);
pan.add(butt);                }
badd.addActionListener(this);
pan.add(badd);
for ( int i=4; i<=6; i++)
JButton butt=new JButton(""+i);
butt.addActionListener(this);
pan.add(butt);
bsub.addActionListener(this);
pan.add(bsub);
for ( int i=7; i<=9; i++)
JButton butt=new JButton(""+i);
butt.addActionListener(this);
pan.add(butt);
bmult.addActionListener(this);
pan.add(bmult);
bclear.addActionListener(this);
pan.add(bclear);
b0.addActionListener(this);
pan.add(b0);
bpoint.addActionListener(this);
pan.add(bpoint);
bequal.addActionListener(this);
pan.add(bequal);
bdiv.addActionListener(this);
pan.add(bdiv);
//pan.add(new Button(""));
setContentPane(pan) ;
public boolean action(Event e, Object o)
//checks for operator keys
if (e.target == badd)
temp1 = temp;     //to "save" for calculation
opr = "+";
else if (e.target == bsub)
temp1 = temp;
opr = "-";
else if (e.target == bmult)
temp1 = temp;
opr = "*";
else if (e.target == bdiv)
temp1 = temp;
opr = "/";
else if (e.target == bequal)
result = calculate(temp1,opr,temp);
tf.setText(Integer.toString(result)); //does the calculation
temp= result; //to be able to do an operation on the result
else if (e.target == bclear)
tf.setText("");
temp1 = 0; //resets the temps and display to 0
temp = 0;
else
//numeric buttons
if (firstDigit)
tf.setText( o.toString() );
firstDigit = false;
temp = Integer.parseInt(tf.getText()); //saves the number in a temp
else
tf.setText(tf.getText() + o.toString()); //for numbers longer than 1 digit
temp = Integer.parseInt(tf.getText());
return true;
firstDigit = true; // GET READY FOR NEXT NUMBER
return true;
public int calculate(int num1,String op, int num2 )
// calculate the numbers
int answers = 0;
if (op == "+")
answers = num1 + num2; //does the calculation for +
else if(op == "-")
answers = num1 - num2; //does the calculation for -
else if(op == "/")
if(num2 == 0)
tf.setText("ERROR");//gives error message if dividing by 0
else
answers = num1 / num2;
else if(op == "*")
answers = num1 * num2; //does the calculation for *
return answers;
public void actionPerformed(ActionEvent e) {
Object source = e.getSource() ;
public static void main(String[] args)     {
try {
UIManager.setLookAndFeel(UIManager.getCrossPlatformLookAndFeelClassName() );
catch (Exception e) {
System.err.println("impossible to use system setting : " + e ); }
Calculator fen = new Calculator("CALCULATOR");
fen.setSize(235, 300);
fen.setVisible(true);
fen.setDefaultCloseOperation(JFrame.EXIT_ON_CLOSE);

I Hope this would help you.
http://www.planet-source-code.com/vb/scripts/ShowCode.asp?lngWId=2&txtCodeId=2275
Thanks,
Vikas Karwal
[email protected]

How implement (Forms Builder ) Calculation Item in JDeveloper ADF?

How implement (Forms Builder ) Calculation Item in JDeveloper ADF?
(Forms Builder ) Property
Calculation -> Calculation Mode=Summary
Calculation -> Formula -> Summary Function=Sum
Calculation -> Formula -> Summarized Block=Block Name
Calculation -> Formula -> Summarized Item=Quantity Item

You can have transient attributes in your VO that do calculations.
http://download.oracle.com/docs/html/B25947_01/bcentities010.htm#BABHGCAH
For summaries here are a few other options:
http://www.freewebalbum.com/blogs/faces/bjanko/blogs.jsp?blog=bjanko20070725180020
http://andrejusb.blogspot.com/2008/01/complex-calculated-values-in-oracle-adf.html

Independent requirement for KANBAN Calculation

Hi all guru,
Now i can use kanban caculation for Semi-FG (it use dependent requirement for calculate) and i want to calculate FG too! but i don't know how to configure to use independent requirement (forecast) for automatic kanban calculation. who expert know please explain to me?
Thank you in advance...
Edited by: Konnapa on Jul 6, 2009 12:31 PM

Kanban Calculation takes place for requirements at a control cycle
level, specifically at a supply area level.The kanban calculation can
therefore be only carried out for dependent requirements that refer to a
supply area. This supply area is usually assigned to the BOM item but
also can be defined in production version or material master.
Please refer the following documentation:
SAP R/3 Enterprise Application Components
Logistics
    Production Planning and Control (PP)
      PP KANBAN
        PP - KANBAN
          Automatic Kanban Calculation
            Calculating Depndt Reqmts for Automatic Kanban Calculation
I am afraid, independent requirements(PIRs in MD61) entered and also
sales order requirements can only be tracked at a plant level, and hence
cannot be included for Kanban calculation. On the same lines the
dependent requirements that are defined only at a storage location level
are also not included!
In fact KANBAN scenario is suitable for the business where the
procurement need not be planned well in advance, all procurement can be
initiated at any time once KANBAN is empty. This is the most important
characteristic of KANBAN. The introduction of PIRs into this scheme
contradicts this very objective of 'avoiding' lead times in planning.
This is also the reason why KANBAN calculation is more appropriate for
dependent requirements from supply area, characteristic of most
automotive industries, where make-to-stock planning happens mostly at
higher Sub-assembly levels and not at component levels.
Kanban is more relevant to only one subset of MRP requirement elements
i.e, the Dependent requirements.
Also, incase you want to include all storage locations / supply areas
in the plant for the control cycle in question,then in PK02, for the
said control cycle , under Kanban calculation tab, click on "Additional
Requirements Button" and enter the plant (without the storage
location/supply area). In this case,the automatic kanban calculates all
the dependent requirements in the plant.
In automotive releases we have the BADI MPKC_REQ_SELECTION
hooked in the function module PK_READ_DEPENDENT_REQUIREMENTS.
Customers, who want additional requirements such as the ones from APO to
be included for calculation, can program here.
Production Supply area is the key for the requirements to match with the
control cycle. Hope I have clarified your query.

Tax Calculation of free goods

Hi
We have a requirement where the client wants only VAT to be posted in GL accounts and not the price.For this I tried free goods condition type R100 with AltCBV 28.But the VAT value is also coming zero. I want the VAT to be calculated on Pricing condition and then give 100% discount.
Apart from this I also tried to make pricing condition statistical and calculate VAT on it but then also system gives zero value for VAT.
Also wondering if the scenario can be addressed with Free of Change Dellivery.

Hi
Normally in scenario where you are dealing with samples , there are cases you have to charge only TAXES / EXCISE part.
Here my SUGGESTION is you can handle this through a simple sales order process, where you have to configure a new pricing procedure.
1. Create a new document type to handle samples.
2. Create a New pricing procedure where you can keep the basic price condtion as Statistical and rest all same as wht is is there your main pricing procedure. Just juggle with the TO-FROM to capture the TAX part in the total.
3. Doc pricing procedure will help you to pick the new Pricing procedure
4. Now Process this as a normal sales order
5. This new document type will help you to have a proper reporting.
The only constraint here is USER has to punch a fresh order seperately for such scenario. He cannot give a free good in the same sales order which is used as standard.
The other way is you can configure a FREE GOOD Determination procedure as suggested where you need to then have your Single pricing procedure accomodating the same scenario.
Thanks
RB

IF statement in Calculated Field for Share point, doesnt calculate sum in my Excel Pivot table.

Hi Everyone
I used this in SP calculated column field.
=IF([Shift Sched]="1pm to 10pm","0",IF([Shift Sched]="2pm to 11pm","1",IF([Shift Sched]="3pm to 12am","2",IF([Shift Sched]="4pm to 1am","3",IF([Shift Sched]="5pm to 2am","4",IF([Shift
Sched]="6pm to 3am","5",IF([Shift Sched]="7pm to 4am","6",IF([Shift Sched]="8pm to 5am","7",IF([Shift Sched]="9pm to 6am","8",IF([Shift Sched]="10pm to 7am","8",IF([Shift
Sched]="11pm to 8am","7",IF([Shift Sched]="12pm to 9am","6",IF([Shift Sched]="1am to 10am","5",IF([Shift Sched]="2am to 11am","4",IF([Shift Sched]="3am to 12pm","3",IF([Shift
Sched]="4am to 1pm","2",IF([Shift Sched]="5am to 2pm","1",IF([Shift Sched]="6am to 3pm","0",IF([Shift Sched]="7am to 4pm","0",IF([Shift Sched]="8am to 5pm","0",IF([Shift
Sched]="9am to 6pm","0",IF([Shift Sched]="10am to 7pm","0",IF([Shift Sched]="11am to 8pm","0",IF([Shift Sched]="12pm to 9pm","0"))))))))))))))))))))))))
it was able to work fine however my issue is when i extract the information to excel and use a pivot table the table is not able to calulate the sum of the value for this field. Can you please help me with this. this is for an Attendance traker for Night
Differential pay for employees. they create a daily log of their shift schedule and if i summarize this in pivot the value in the calculated field for this is not getting the sum.
Thanks,
Norman

Hi Everyone
I used this in SP calculated column field.
=IF([Shift Sched]="1pm to 10pm","0",IF([Shift Sched]="2pm to 11pm","1",IF([Shift Sched]="3pm to 12am","2",IF([Shift Sched]="4pm to 1am","3",IF([Shift Sched]="5pm to 2am","4",IF([Shift
Sched]="6pm to 3am","5",IF([Shift Sched]="7pm to 4am","6",IF([Shift Sched]="8pm to 5am","7",IF([Shift Sched]="9pm to 6am","8",IF([Shift Sched]="10pm to 7am","8",IF([Shift
Sched]="11pm to 8am","7",IF([Shift Sched]="12pm to 9am","6",IF([Shift Sched]="1am to 10am","5",IF([Shift Sched]="2am to 11am","4",IF([Shift Sched]="3am to 12pm","3",IF([Shift
Sched]="4am to 1pm","2",IF([Shift Sched]="5am to 2pm","1",IF([Shift Sched]="6am to 3pm","0",IF([Shift Sched]="7am to 4pm","0",IF([Shift Sched]="8am to 5pm","0",IF([Shift
Sched]="9am to 6pm","0",IF([Shift Sched]="10am to 7pm","0",IF([Shift Sched]="11am to 8pm","0",IF([Shift Sched]="12pm to 9pm","0"))))))))))))))))))))))))
it was able to work fine however my issue is when i extract the information to excel and use a pivot table the table is not able to calulate the sum of the value for this field. Can you please help me with this. this is for an Attendance traker for Night
Differential pay for employees. they create a daily log of their shift schedule and if i summarize this in pivot the value in the calculated field for this is not getting the sum.
Thanks,
Norman

If statement in Custom Calculation Script

I have 16 fields and if even one of them ="1" I have to list it in another field. I do not want to count or sum. If one of those fields has a 1 in it I just want the other field to display Y and if none have a 1 I want that field to display N.
Please help.
Thank you in advance~mjc

You need to write a compound logical statement to evaluate all of the values and that statement needs to evaluate to true or false.
Do you know how to write JavaScript?
Do you know how to enter JavaScript calculations into a form field?
For custom calculation of the text field I could write something like:
// define an array of the field names to check
var aNames = new Array("Text1", "Text2", "Text3", "Text4",
"Text5", "Text6", "Text7", "Text8",
"Text9", "Text10", "Text11", "Text12",
"Text13", "Text14", "Text15", "Text16");
// define a logical variable that is true if any field has a value of 1 - default is false or no field has a value of 1
var bMatch = false;
// value for text field
var TextValue = 0;
// logical value of field being equal to 1 test
var FieldIs1 = false;
// loop through all the fields and test the fields value
for(i = 0; i < aNames.length; i++) {
// logically OR the result of field i value equal to true with bMatch
// get the value of field
TextValue = this.getField( aNames[i] ).value;
// test the value of the field
FieldIs1 = Number(TextValue) == 1
// logically OR the 2 values
bMatch = FieldIs1 | bMatch;
} // end field processing
// set the field value
if(bMatch == true) {
event.value = "Y";
} else {
event.value = "N";
You will need to change the field names to match your fields. You can add more field name or remove field names as needed and the script will adjust for the number of field names.

If statement in calculated batch characteristic (dependencies)

I have a little problem with calculating a certain batch characteristic.
The situation is the following:
I have batch char A, batch char B and batch char C. Batch char C is the result of the sommation of char A and B. The problem I have now is that batch char C only should be calculated when batch char A and B are different from 0.
I have a custom build interface that imports QM data to the batch chars. Default, all my batch chars are set to 0 so if I just say $self.charC = $self.charA + $self.charB, I always get a value.
Is it possible to some sort of IF statement to check if the value is different from 0?

Dear,
You need to try with variant table
take all the combination and enter in a variant table and see the result...it works
example
A     B      C
0      0      space
0      1      sapce
1      1      space
I hope you got it

Pension not calculated when EE is hired mid-month

Hi All
Please suggest for the following....
When an Employee is hired in the middle of the month, the system doesn't calculate Pension Contribution.
Like if an EE is hired on 10th April. The system will calculate all payments & deductions, but it is not calculating the Pension Contributions.
I am maintaining IT 169, 171 for Pension Contribution.
The problem I found behind this is.....(WIth the help of an ABAPer)
-: System checks the Payroll Period Start Date with the Org. Assignment start date. When it doesnu2019t match, the system does not calculate the Pension Contribution.
For the time being I solved this through the following action -: In debugging, I canceled this condition (skipped this check). Then it calculated the Pension Contribution.
But, this is not the right solution for achieving that as we are changing standard SAP coding.
Please suggest any solution for the same.
Thanks & Regards

If your schema has p0169 with BEG that will happen, try put below Param1 which fits your requirement.
BEG
Infotype records are evaluated on the payroll period begin date.
No changes within the current payroll period are taken into
consideration.
No proration of contributions takes place, even if the record ends
within the current payroll period.
END
Infotype records are evaluated on the payroll period end date.
No changes within the current payroll period are taken into
consideration.
No proration of contributions takes place, even if the record begins
within the current payroll period.
CHK
Infotype records are evaluated on the payroll check date (the pay date),
regardless of whether the check date falls into the payroll period
itself.
A record whose validity starts after the end date of the current payroll
period is still evaluated if the check date (which lies in the future)
falls within the validity period of the infotype.
FRST
Infotype records are evaluated if there is any intersection of plan
infotype and payroll period. The first intersection is taken to
determine the full period deduction amount which is stored without
proration.
LAST
Infotype records are evaluated if there is any intersection of plan
infotype and payroll period. The last intersection is taken to determine
the full period deduction amount which is stored without proration.

Calculating Calculating

Similar Messages

Maybe you are looking for