Can Cisco 1041N WAP Be Configured as a Stand-alone device

I'm out at a remote site and we've been futzing with configuring this to be the site's WAP.  But it's looking like it's
meant to only be used in conjunction with a central controller.  Is there any way to have it work like a stand-alone
device like the good old 1200 (which I am missing very much at the moment).

According to the Cisco Software Download Centre, you can load autonomous IOS into the 1040 AP.
Products
Wireless
Access Point
Cisco Aironet 1040 Series
Cisco Aironet 1040 Series Access Point
IOS Software
Follow the proceedure below to convert the AP from CAPWAP to Autonomous IOS.
Using a TFTP Server to Return to a Previous Release

Similar Messages

  • Can AIR-CAP1602i-x-k9 be converted to stand alone??

    can air-cap1602i-x-k9 be converted to stand alone??

    Yes , you can convert the AP to stanadlone  by pushig the below image  into the AP
    http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB3a&relind=AVAILABLE&rellifecycle=ED&reltype=latest
    You can use the below method to convert the same
    Using a TFTP Server to Return to a Previous Release
    Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release
    using a TFTP server: This method is for local conversion.
    Step 1 The PC on which your TFTP server software runs must be configured with a static IP address in the range
    of 10.0.0.2 to 10.0.0.30.
    Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a
    1200 series access point) in the TFTP server folder and that the TFTP server is activated.
    Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200
    series access point.
    Step 4 Connect the PC to the access point using a Category 5 or better Ethernet cable.
    Step 5 Disconnect power from the access point.
    Step 6 Press and hold the MODE button while you reconnect power to the access point.
    Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the
    MODE button.
    Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED
    blinking green.
    Thanks..

  • Can someone send me the link to the stand alone version of light room 5 were I can buy it. Thank you in advance

    Were can I found the stand alone version of lightroom 5?

    Rob,
    Thank you so much.
    In one way or another I managed to purchase the upgrade of lightroom instead of full version.
    It is now corrected, thank you so much
    Best Regards,
    Fredrik
    18 aug 2014 kl. 11:11 skrev Rob Cole <[email protected]>:
    Can someone send me the link to the stand alone version of light room 5 were I can buy it. Thank you in advance
    created by Rob Cole in Photoshop Lightroom - View the full discussion
    If you go to the main Lightroom page - where most links take you to cloud signup, at the very bottom, click on "Products" - scroll down to 'Lightroom'..
    Products
    Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at https://forums.adobe.com/message/6649902#6649902
    Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
    To unsubscribe from this thread, please visit the message page at . In the Actions box on the right, click the Stop Email Notifications link.
    Start a new discussion in Photoshop Lightroom by email or at Adobe Community
    For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

  • How can I read the complex data for the stand-alone offline time-frequency analyzer, which only accept real data, that is one-column or one row data ?

    I have real complex data (i,q data) for the ISAR imaging. I don't have any knowledge of Labview programming. I bought this signal processing toolset to use only stand-alone time-frequency analyzer.

    In the LabVIEW functions palette on the block diagram, if you go to Numeric>>Complex you have to VI's that splits a complex number into rectangular or polar components. Click on the help file for those VI's to see the kind of datatypes you can wire to them.
    Cyril Bouton
    Active LabVIEW Developper

  • Can the new airport be used as a stand alone to the printer for the iPad

    Can the new airport express be used with a network printer as a stand alone with just a iPhone and a iPad, no computer to set it up with?
    It has Internet access.

    You're referring to Target Display Mode Mid 2011 iMacs  this letter will explain how it works or in your case will not work () with your mid 2010 MBP. Sorry to be the bearer of bad news.

  • Can I purchase Adobe Premiere Pro as a stand alone?

    Hello,
    I have the Adobe Design Suites. Can I purchase the Adobe Premiere Pro without buying the full Production Suite?

    Where would i do so. All I see is Upgrade portion here
    http://www.adobe.com/products/premiere.html
    Even though I don't have a previous version of Adobe Premeire, would this be the one I select?

  • Can we install ESR (ES repository)  in a stand alone fashion?

    I guess NOT. Because ERS needs a JAVA engine, right?
    Thanks!

    Yes, the project owner need to be aware of it. As bazzza mentioned, the Agent will be installed on the Linux box and it will connect to the database on linux at set intervals to collect monitoring data.
    So you are looking at additional resource usage (Memory, CPU, Disk) on Linux box. And you should plan for additional Oracle Connection License for the database if you use Named User License.

  • Can anyone tell me is BC a stand-alone proprietary system or can it be hosted by another provider??

    @Have had a website built using BC by a website company that I have parted ways with
    after 18 months of hell.  I now have the BC platform and website, but have no idea
    what I'm doing.  They never activated the emails for me, but after tearing my hair out
    I managed to get one email working, but just how is a total mystery.
    Can anyone tell me if BC is a stand-alone proprietary system that is operated by Adobe
    or can I get another Hosting company to take it over for me?? I would very much
    appreciate someone's help before I go totally crazy.  I can't get in touch with anyone to
    talk to from Adobe - tried the Skype number several times and it never answered - I rang
    it what was 9-5 US time, but no luck.  Can't find a living person to talk to here in
    Australia!!
    HELP ME PLEASE.....

    Hi
    Adobe Business Catalyst is a hosted CMS. That means you need to host in ADOBES datacentre for the CMS to work.
    But that's not all bad news because Adobe apply the updates for you so you're always running the latest software. AND the SSL certficates / DNS hosting etc etc etc is all included in your website.
    The Business Catalyst is designed so website owners are connected with a partner. The partner helps to ensure you've got someone to lead on for support, or when something falls over. It's highly recommended to have access to a good partner. Sounds like you ended up with a dud.
    So to answer your question directly. No, you can't just transfer your site to another hosting company.
    BUT - you can transfer your site away from your existing Partner to someone else.
    If you're in Australia I can offer you a really attractive wholesale solution with no costs to you and will help you transfer free of charge.
    I can also offer you Business Catalyst training if you need this.
    Let me know if you need help getting this all sorted
    Brett Stockley
    www.prettydigital.com.au
    02 9212 4485

  • Can a inspire p5800 be used without a computer, as a stand alone speaker system

    Can an Inspire P5800 be used as a stand alone speaker system? Here is my story. I just got this speaker system from my girlfriend who did not know that it had to be hooked up to a computer/soundcard etc... She thought it would just hook up to my MP3 player and be used as a speaker system downstairs in my shop. It looks like the decoder DDTS-100 could be bought and used as a stand alone sound adapter? Or is there a cheaper way? The only other way I can see is a triple headphone adapter that has one 1/8 inch plug going to three 1/8 inch jacks that can be fitted with a 1/8 inch plug to plug cable in each jack, then those going into the back of the subwoofer/connector area. Would that be a mono source that way? Any help would be appriciated. marc

    I have set this system up with a creative zen vision m without using a computer just stand alown, but i have only been able to get the subwoofer, front left and right speaker to work. I dont know if that helps.

  • Can cisco MSE(mobility service engine) configured to work with non-cisco access points?

    I understand that access points can be configured to forwards all the probe requests to cisco wifi controller. cisco MSE(mobility service engine) gets the probes from wifi controller to find the location of the mobile devices.
    My question, can cisco MSE(mobility service engine) be configured to work with non-cisco access points?

    No and the reason why is the NMSP communication from the MSE to the WLC. Other vendors don't support this so there is no communication happening.
    -Scott

  • Can Cisco Configuration Professional to use IPS feature ?

    Dear Expert
    Hello.
    Could you tell me about Cisco Configuration Professional.
    I'd like to try the IOS-IPS on Cisco2901-SEC/K9.
    I was search in CCO about Cisco Configuration Professional.
    The Cisco2901-SEC/K9 does not support SDM.
    But, The Cisco2901-SEC/K9 supported the Cisco Configuration Professional.
    Can Cisco Configuration Professional to use IPS feature like SDM?
    Regards,
    Takuro.

    Hi,
    yes, you can configure IOS IPS from Cisco Configuration Professional.
    CCP has a wizard to guide you through the process, this is a link for that :
    http://www.cisco.com/en/US/prod/collateral/iosswrel/ps6537/ps6586/ps6634/prod_white_paper0900aecd8066d265.html
    i hope this helps you.
    Mashal

  • HP Wireless Printers cannot connect to WPA2-secured WiFi networks with Cisco/Meraki WAPs

    In the last two months, I've had the displeasure of working with two very different HP printers and attempting to make them work on a WPA2-secured wireless network.  All attempts to authenticate fail with "invalid phassphrase". 
    I'm not the first person to encounter this, it's a problem with many different HP wireless printers (I just happen to have physical access to the OfficeJet Pro 8610 & Deskjet 3511). 
    My equipment is a Cisco ASA 5505 Firewall running ASA 9.1x & Cisco Aironet 1142 running IOS 15.3.x. 
    What does work on the WPA2/AES SSID:  Apple MacBook Air running OSX 10.10.2, Three Windows-Based laptops running Windows 8.1 Update 1, an iPhone 5s, Three Windows Phone 8.1 devices, Roku 2, PlayStation 4, PlayStation 3, Sharp Aquos TV, Amazon Streaming Stick, and an Android Tablet (Jellybean).  Basically, everything. 
    What does not work on the WPA2 network:  OfficeJet Pro 8610 & Deskjet 3511.
    To test the theory there is a problem with HP's implementation of WPA2 with regard to Cisco Aironet IOS, I built out a second SSID that only works in WPA/TKIP mode.  This solution works.  Both HP printers will join the WPA/TKIP network.
    So, I'm able to demonstrate there is a certain connectivity issue.  When i look at AAA Debug on the WAP's console, I can observe the HPs attempt to authenticate "Bind I/F" on the WPA2 SSID, however they do not achieve authentication and do not pass the AAA phase.  However, on the WPA SSID, they bind and authenticate successfully. 
    To help illustrate this, here is my WAP running config.  It's about as simple as it can get.  There is no relevant MAC filtering or ACLs bound to any interface.  Noting that I have an ACL on remote access to the WAP (i.e. Locked down to SSH, disabling telnet).  The main point being that the ASA firewall is not a factor in this problem as the issue is at the WAP before WPA2 authentication can complete, therefore the printers never reach the network / when the printers connect to the WPA network, the operate fully & correctly. 
    If anyone at HP can indicate why this particular config is somehow improper or broken, that would be fantastic.  There should be no reason why Cisco / Meraki WAP owners have to lower wireless encryption standards just for a printer, be forced into wired, create separate SSIDs with lower encryption specifically for a device. 
    Building configuration...
    Current configuration : 6064 bytes
    ! Last configuration change at 12:46:47 UTC Fri Aug 20 1993 by admin
    version 15.3
    no service pad
    service timestamps debug datetime msec
    service timestamps log datetime msec
    service password-encryption
    hostname 10-10-50-1
    logging buffered 1024768
    logging rate-limit console 9
    aaa new-model
    aaa authentication login default local
    aaa authorization exec default local
    aaa session-id common
    no ip source-route
    no ip cef
    ip domain name freedom.local
    dot11 syslog
    dot11 vlan-name inside vlan 50
    dot11 vlan-name inside-wpa-only vlan 70
    dot11 ssid inside
       vlan 50
       band-select
       authentication open
       authentication key-management wpa version 2
       mbssid guest-mode
       wpa-psk ascii 7 xxxxxx
       information-element ssidl
    dot11 ssid inside-wpa-only
       vlan 70
       band-select
       authentication open
       authentication key-management wpa
       mbssid guest-mode
       wpa-psk ascii 7 xxxxxx
       information-element ssidl
    dot11 band-select parameters
       cycle-count 3
       cycle-threshold 200
       expire-supression 20
       expire-dual-band 60
       client-rssi 75
    dot11 wpa handshake timeout 500
    dot11 network-map
    username ADMIN privilege 15 secret 5 xxxxxx
    ip ssh version 2
    bridge irb
    interface Dot11Radio0
     no ip address
     no ip route-cache
     encryption vlan 50 mode ciphers aes-ccm
     encryption vlan 70 mode ciphers aes-ccm tkip
     ssid inside
     ssid inside-wpa-only
     antenna gain 0
     mbssid
     speed  basic-1.0 basic-2.0 basic-5.5 basic-11.0 6.0 9.0 12.0 18.0 24.0 36.0 48.0 54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15.
     channel 2412
     station-role root
     l2-filter bridge-group-acl
    interface Dot11Radio0.50
     encapsulation dot1Q 50 native
     no ip route-cache
     bridge-group 1
     bridge-group 1 subscriber-loop-control
     bridge-group 1 spanning-disabled
     bridge-group 1 block-unknown-source
     no bridge-group 1 source-learning
     no bridge-group 1 unicast-flooding
    interface Dot11Radio0.70
     encapsulation dot1Q 70
     no ip route-cache
     bridge-group 70
     bridge-group 70 subscriber-loop-control
     bridge-group 70 input-address-list 700
     bridge-group 70 output-address-list 700
     bridge-group 70 spanning-disabled
     bridge-group 70 block-unknown-source
     no bridge-group 70 source-learning
     no bridge-group 70 unicast-flooding
    interface GigabitEthernet0
     no ip address
     no ip route-cache
     duplex auto
     speed auto
    interface GigabitEthernet0.50
     encapsulation dot1Q 50 native
     no ip route-cache
     bridge-group 1
     bridge-group 1 spanning-disabled
     no bridge-group 1 source-learning
    interface GigabitEthernet0.70
     encapsulation dot1Q 70
     no ip route-cache
     bridge-group 70
     bridge-group 70 spanning-disabled
     no bridge-group 70 source-learning
    interface BVI1
     mac-address xxxx.xxxx.xxxx
     ip address 10.10.50.1 255.255.255.0
     no ip route-cache
    ip forward-protocol nd
    ip http server
    ip http authentication aaa
    no ip http secure-server
    ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
    ip route 0.0.0.0 0.0.0.0 10.10.50.2
    logging history size 100
    access-list 111 permit tcp any any neq telnet
    bridge 1 route ip
    line con 0
     access-class 111 in
    line vty 0 4
     access-class 111 in
     length 0
     transport input ssh
    line vty 5 15
     access-class 111 in
     transport input ssh
    end

    I get the same behavior with a laserjet m451nw. I need to enable tkip to get the printer working, it doesn't support pure aes-ccm (every other device here supports pure aes-ccm, even cheap ones), although it's advertised as working.
    The following snippet of config works, but I still think it should work without the tkip "hack".
    dot11 ssid whatever
    vlan 1
    band-select
    authentication open
    authentication key-management wpa version 2
    interface Dot11Radio0
    encryption vlan 1 mode ciphers aes-ccm tkip

  • Cisco desktop administrator Services Configuration Multiline, Monitoring & Recording Remove VoIP/Recording & Playback Services

          I remove default VOIP Monitor Service in "Cisco desktop administrator>Services Configuration > Multiline, Monitoring & Recording >Remove VoIP/Recording & Playback Services". Now I can't choose in  "Services Configuration > Multiline, Monitoring & Recording > VoIP Monitoring Device" Default VOIP Monitor Service. How can I return choice my VOIP Monitor Service(IP UCCX)?     

    Hi Kalitamih,
    This can be regenerated by the Cisco Desktop VOIP Monitor Service.
    Please stop the service and start it (do not restart). Let me know how it goes and if it resolves the problem.
    Regards,
    Arundeep

  • License Cisco ESA in Cluster Configuration

    Guys,
    Do you have any idea about license Cisco ESA in Cluster Configuration
    > If i have two appliance in cluster configuration and i have 1000 user, which option for license i must buy ?
    1. Just one license for two appliance (which in cluster configuration) with 1000 user capacity
    2. Two license with 500 user capacity for each appliance, appliance 1 with 500 user capacity license appliance 2 500  user capacity license
    3. Other license.
    BR

    You only need to buy 1000 user licenses for which ever options or packages you buy. The only option that is not based on the number of users is if you want a Cisco Content Security Management Appliance or SMA for centralized reporting and quarantine. 
    Another good thing to note, is that if you have a virtual environment the hardware appliances are no longer required, and are not nearly as expensive as they were in the past. So depending on your requirements you may be off the ground pretty quick.
    Also make sure to get all your features bundled. I would at least get AMP, Sophos A/V, DLP, and Encryption. This also means you can transfer and copy your license to as many appliances (Physical or Virtual) you need to support your environment. 

  • Juniper SSG and Cisco ACS v5.x Configuration

    I searched for a long time unsuccessfully trying to find a resolution to my SSG320M and Cisco ACS v5.x TACACS dilemma.  I finally got it working in my network, so I'm posting the resolution here in case anyone else is looking.
    Configure the Juniper (CLI)
      1. Add the Cisco ACS and TACACS+ configuration
         set auth-server CiscoACSv5 id 1
         set auth-server CiscoACSv5 server-name 192.168.1.100
         set auth-server CiscoACSv5 account-type admin
         set auth-server CiscoACSv5 type tacacs
         set auth-server CiscoACSv5 tacacs secret CiscoACSv5
         set auth-server CiscoACSv5 tacacs port 49
         set admin auth server CiscoACSv5
         set admin auth remote primary
         set admin auth remote root
         set admin privilege get-external
    Configure the Cisco ACS v5.x (GUI)
      1. Navigate to Policy Elements > Authorization and Permissions > Device Administration > Shell Profiles
            Create the Juniper Shell Profile.
            Click the [Create] button at the bottom of the page
                    Select the General tab
                            Name:    Juniper
                            Description:  Custom Attributes for Juniper SSG320M
                    Select the Custom Attributes tab
                        Add the vsys attribute:
                            Attribute:                vsys
                            Requirement:       Manadatory
                            Value:                    root
                            Click the [Add^] button above the Attribute field
                        Add the privilege attribute:
                            Attribute:                privilege
                            Requirement:       Manadatory
                            Value:                    root
                                    Note: you can also use 'read-write' but then local admin doesn't work correctly
                            Click the [Add^] button above the Attribute field
                    Click the [Submit] button at the bottom of the page
    2. Navigate to Access Policies > Access Services > Default Device Admin > Authorization
            Create the Juniper Authorization Policy and filter by Device IP Address.
            Click the [Customize] button at the bottom Right of the page
                    Under Customize Conditions, select Device IP Address from the left window
                            Click the [>] button to add it
                    Click the [OK] button to close the window
                    Click the [Create] button at the bottom of the page to create a new rule
                            Under General, name the new rule Juniper, and ensure it is Enabled
                            Under Conditions, check the box next to Device IP Address
                                    Enter the ip address of the Juniper (192.168.1.100)
                            Under Results, click the [Select] button next to the Shell Profile field
                                    Select 'Juniper' and click the [OK] button
                            Under Results, click the [Select] button below the Command Sets (if used) field
                                    Select 'Permit All' and ensure all other boxes are UNCHECKED
                            Click the [OK] button to close the window
                    Click the [OK] button at the bottom of the page to close the window
                    Check the box next to the Juniper policy, then move the policy to the top of the list
                    Click the [Save Changes] button at the bottom of the page
    3.  Login to the Juniper CLI and GUI, and attempt to change something to verify privilege level.

    Cisco Prime LMS is not designed to manage appliances like the ACS. ACS is not on the LMS supported device list and I would doubt that it would be as LMS's functions are mostly not applicable to the appliance or software running on it.
    You can use ACS as an authentication source for LMS, but authorization is still role-based according to the local accounts on the LMS server.

Maybe you are looking for