Can not access web interface: Linux: permission denied

When starting my oracle-xe on centos5 it works but i can not open the web interface. During install i have configured it on port 81 and this is the error i get when starting the db:
30-MAY-2010 19:17:54 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=localhost.localdomain)(USER=oracle))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=169869568)) * status * 0
Error listening on: (Description=(Address=(Protocol=tcp)(Port=81)(Host=localhost))(Presentation=HTTP)(Session=RAW))
30-MAY-2010 19:17:57 * service_update * XE * 12546
TNS-12546: TNS:permission denied
TNS-12560: TNS:protocol adapter error
TNS-00516: Permission denied
Linux Error: 13: Permission deniedFirewall and seLinux are disbled.
I have installed oracle-xe as root and added root to the dba-group
What could be the issue for this?
Edited by: Yannick.O on May 30, 2010 10:35 AM

You have to use some port higher then 1024. Ports below 1024 are reserved for root user only.

Similar Messages

Can not access web wifi simble on but can not connect the the internet

wifi on but can not access internet

I COULD SOLVE THE PROBLEM!!! : CHANGE YOUR ISP
I it is obvious that we are talking about different issues, but all arise from the same origin. I am a surgeon and fortunately one of my patients is executive manager of one of biggest ISP companies from which I have bought my Internet service for home and my clinic.
One day I told him the problem and he promised to check it for me. A few days later he called me and discussed the exact problem (unfortunately as I am not I.T professional, I couldn’t understand it well, I can just remember he was talking about MULTIPLEXING incompatibility between Mac security settings and that specific ISP multiplexing settings, He also said they had similar problems with some Linux users. I can remember he relate the problem to cheap ISP hardware, which leads to security issues which are ignored by Windows Systems but leading to connection blockade in Mac Browsers. That’s why if you PING yahoo.com, you will see everything is OK but your browsers are not working)
In fact this is a hardware issue which is related to ISP (Internet Service Provider) security and not your Mac.
The day after, I took my MacBook to some ISP offices and asked them to let me connect to their line just for a test. “ Surprisingly I found out without changing my MacBook’s settings it works well with some ISPs and not with others!! “
I have two ADSL lines: one at home and one in my clinic. First I changed my home ISP and everything is well at home from the day I did the change. But before changing my clinic’s ISP it worked at home and not at the clinic. Later I changed my clinic’s ISP and afterward never I had any problem. This proves ( as that manager said also) this problem is related to ISP and not Mac itself and that’s why Apple could not have resolved the problem yet: different ISPs have different issues.
Here I can make some suggestions:
1- First, take your MacBook into different ISP offices and find the one which works well (before making the contract and paying money to the ISP, restart the Mac or send it into sleep mode repeatedly to make sure the connection never drops with restart or sleeps)
2- Change your modem: Modems as TP-LINK, D-LINK, are not well compatible with Mac. Apple modems or Linksys are perhaps the best choices (this is not main cause of internet drop, but can affect the performance)
3- Make sure your neighbor’s Wi-Fi is not exactly on the same channel as you are using (I use iStumbler for finding my neighbor’s channels)
4- Find best DNS: ask your ISP to provide you most compatible DNS’s for you. Perhaps most known DNSs are 8.8.8.8 and 4.2.2.4.It helps you to browse the Internet more efficiently
Some people in other forums suggested that upgrading to Mountain Lion has helped them. But It didn't work for my clinic's line. Just changing the ISP at clinic resolved my problem
BETWEEN THESE 4 SUGGESTIONS, THE FIRST ONE IS THE MAIN SOLUTION AND NO 2-4 CAN HELP THE PERFORMANCE.
Move on!!! Change your ISP and let me know if it works!!!!

Can't access/mount hard drive, Permission denied message in Disk Utility.

Hello,
Need some help here. I was upgrading from 10.4 to 10.5. I got an error message when I tried to upgrade from the DVD. My hard drive had an exclamation mark by it and I was told I would need to erase it in order to install. When I tried quitting the installer, I had to go through startup disk to pick my Hard drive, which showed it had 10.4 installed. When I tried restarting, it would only boot off of the DVD. I checked startup disk again, but my hard drive was now not visible. I have a tower with a back-up system on it. When I picked it, it started up fine. I went under disk utility and the hard drive is listed, but is ghosted/grayed out. Repair & Verify Disk permissions are ghosted back as well.When I try to repair or verify disk, it says it can't it gives me the disk number and sector number and Permission Denied. I poked around on disk utility for info, and it looks like it doesn't have a mount point anymore and under permissions, it says that they are not enabled. So, apparently the access privileges have been erased & I don't know how to mount my disk again. I'm assuming I need some sort of commmand line in Terminal to restore my priveleges or get it to auto-mount. I do not want to erase my drive to upgrade. All my applications are on that drive. Please help!
Message was edited by: koobiak

See if Niel's User Tip can help you: I accidentally set a disk's permissions to No Access .

Can only telnet from other switches to a SG300 switch. Also can't access web interface.

For whatever reason I can telnet from another switch to the SG300 switch but not directly to the switch. I also can't access the web interface or ping the switch. Any help would be appreciated. Here is the running config
config-file-header
WasteWaterSG30010MPP
v1.3.5.58 / R750_NIK_1_35_647_358
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end xxxxxxxxxxxxxxxxxxxxxxxx
vlan database
default-vlan vlan 2
exit
vlan database
vlan 2,75,200,999
exit
voice vlan id 200
voice vlan oui-table add ________
voice vlan oui-table add _phone_____________
voice vlan oui-table add ___________________
voice vlan oui-table add ______________
voice vlan oui-table add
voice vlan oui-table add ___________
voice vlan oui-table add ___
voice vlan oui-table add ______________
hostname WasteWaterSG30010MPP
line console
exec-timeout 0
exit
line telnet
password 382fda4a4a26e6637edac0eb8b8ba4581087d32d encrypted
exit
line console
password 382fda4a4a26e6637edac0eb8b8ba4581087d32d encrypted
exit
enable password level 15 encrypted 382fda4a4a26e6637edac0eb8b8ba4581087d32d
username admin password encrypted 382fda4a4a26e6637edac0eb8b8ba4581087d32d privi
lege 15
snmp-server location XXXXXXXX
snmp-server community String1 ro view Default
sntp server 172.16.2.1
ip telnet server
interface vlan 2
ip address 172.16.2.23 255.255.255.0
no ip address dhcp
interface gigabitethernet1
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport mode access
switchport access vlan 999
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type unknown
interface gigabitethernet2
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet3
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet4
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport mode access
switchport access vlan 999
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type unknown
interface gigabitethernet5
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet6
spanning-tree portfast
switchport mode access
interface gigabitethernet7
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet8
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet9
spanning-tree link-type point-to-point
switchport trunk allowed vlan add 75,200,999
switchport trunk native vlan 2
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
interface gigabitethernet10
spanning-tree link-type point-to-point
switchport trunk allowed vlan add 75,200,999
switchport trunk native vlan 2
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
exit

A member of which VLAN ID is that device from which you trying to reach that switch?
Is that device directly connected to switch WasteWaterSG30010MPP? If yes, to which port?
If you are connecting from different VLAN than VLAN2, are you using routing between VLANs? Where is that routing device connected to?
> I also have another switch that connects to the network through this switch and am able to telnet to it.
that second switch member of same VLAN 2? Or management is part of different VLAN?
..too few information to be able to give you final answer.

Cisco RM-1252G-A-K9 can't access web interface

I hope I am in the correct forum for this topic?
For some reason I cannot access the web interface in order to configure this device. I have it connected to a router (DHCP). The router assigns an IP Address and I can ping it. If I attempt to go to that IP Address in any web browser. the page cannot be displayed. I've reset it several times. I have 2 of these and same problem. Am I missing something obvious? I sure hope so...

Connecting to the Access Point Locally
If you need to configure the access point locally (without connecting it to a wired LAN), you can connect a PC to its console port by using a DB-9 to RJ-45 serial cable.
Follow these steps to open the CLI by connecting to the access point console port.
Step 1 Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and to the COM port on the PC.
Step 2 Set up a terminal emulator on your PC to communicate with the access point. Use the following settings for the terminal emulator connection: 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.
Assigning an IP Address Using the CLI
When you assign an IP address to the access point using the CLI, you must assign the address to the BVI. Beginning in a privileged EXEC mode, follow these steps to assign an IP address to the access point BVI using the console port:
Command
Purpose
Step 1
enable
Enter privileged EXEC mode.
Step 2
configure terminal
Enter global configuration mode.
Step 3
Interface bvi1
Enters interface configuration mode for the BVI.
Step 4
ip address address mask
Assigns an IP address and subnet mask address to the BVI.
Step 5
end
Return to privileged EXEC mode.

Intermittent can not access web sites.

I have a HughsNet satelight dish/ HughsNet modem. I have a
WRT 160N v3 rounter that routes two computers (mine and my wife's) that are
connected to the router with Cat 5 cables. Each computer has a printer attached to
the local computer only (no sharing). We have had several power outages.
We have been having increasing problems with connecting to websites and
connecting to AOL. We have these problems with both AOL and Google Chrome.
The error messages are: "The web address could not be found", and onece I got:
"More than one device is performing address translation (NAT)". Also, some
downloads fail.
What I have already tried: I opened a utility (trouble shooter?) where you type in the
name of the website and it shows the numerical translation...it was working without
error.
These problems occur on both computers and it does not matter if only one is being used and
the other is sleeping/shut off.
I flushed the DNS cache on both PCs:
(Open up a command prompt (Start > Run > cmd.exe > OK).
Type in the command ipconfig /flushdns)
I made sure that my router's firmware was the latetest available.
I changed the router to distribute Goggle's DNS (8.8.8.8, 8.8.4.4.) instead of the default
I.S.P's.
I opened my Local Host file and checked to make sure that there was not any ip
addresses listed that were not commented out (#).
However, when I went to my wife's comptuer to do the same thing, C:\Windows
\System32\dirivers\etc, there was NO host fire or any other file in the etc folder. Do
not know why, I never deleted it and my wife would not know how to delete it.
When I typed the the ip address for the router on my wifes compter (mine was o.k.),
instead of a blank user name and "admin" as the password, both fields were
blank...keeping me from access it. I tried entering admin as the password and
leaving the username blank, but it told me I had not entered the correct password.
I have disabled my Firewall, no change.
I have run Malwarebytes, and have reset (little red button on the back), the router all
to no avail.
What to do? Any help, ideas please.
Note: I am a rank amature. If you give me an abstract of a possible solution (like: set
your router to bridge mode, I will not be able to do it. Please give any possible
solutions in the "just like I am six years old", format: First type in XXXX then select
XXX, then go to XXXXX etc. An abstract answer will only make sense to other
experts (which I am not), and frustrate me.
Thanks for any help.

In this example, they show you how to change the local IP address to 192.168.2.1. But use 192.168.4.1 to be safe. Don't worry that it says DSL. It's the same principal.
http://kb.linksys.com/Linksys/ukp.aspx?pid=80&vw=1&articleid=3687

HELP! Can not access Web Service

I get error below if webservice asmx and URL of domain do not
match...
they both have to have
http://www or no 'www' in order to run...
otherwise I get the following error below BUT my cross domain
is at
the root of the webserver!! what am I doing wrong???:
[RPC Fault faultString="Security error accessing url"
faultCode="Channel.Security.Error" faultDetail="Unable to
load WSDL. If currently online, please verify the URI and/or
format of
the WSDL
http://www.velocitytrading.net/VTOrdEnt.asmx?WSDL)"
at mx.rpc.wsdl::WSDLLoader/faultHandler()
at flash.events::EventDispatcher/dispatchEventFunction()
at flash.events::EventDispatcher/dispatchEvent()
at
mx.rpc::AbstractInvoker/
http://www.adobe.com/2006/flex/mx/internal::dispatchRpcE\
vent()
at
mx.rpc::AbstractInvoker/
http://www.adobe.com/2006/flex/mx/internal::faultHandler\
at mx.rpc::Responder/fault()
at mx.rpc::AsyncRequest/fault()
at DirectHTTPMessageResponder/securityErrorHandler()
at flash.events::EventDispatcher/dispatchEventFunction()
at flash.events::EventDispatcher/dispatchEvent()
at flash.net::URLLoader/redirectEvent()
CROSS DOMAIN
<?xml version="1.0"?>
<!DOCTYPE cross-domain-policy SYSTEM
http://www.macromedia.com/xml/dtds/cross-domain-policy.dtd">
<cross-domain-policy>
<allow-access-from domain="
http://velocitytrading.net"/>
<allow-access-from domain="
http://www.velocitytrading.net"/>
<allow-access-from domain="*.*"/>
</cross-domain-policy>

Hi CJSteu,
Can u add this crossdomain.xml in ur server bin and dtd also
if needed and check the server is able to invoking the
crossdomain.xml by
url ex:
http://localhost:7001/crossdomain.xml
<?xml version="1.0"?>
<!DOCTYPE cross-domain-policy SYSTEM
"cross-domain-policy.dtd">
<cross-domain-policy>
<site-control permitted-cross-domain-policies="all"/>
<allow-access-from domain="*" to-ports="*" />
<allow-http-request-headers-from domain="*"
headers="*"/>
</cross-domain-policy>

I can not access web based e-mail work account - no problems with ff3.6 when is this going to be looked at i see lots of issues like this highlighted in forum

e-mail program used is windows outlook web

Firefox 4 works with the Outlook Web App generated by Exchange Server 2010. At least in my limited testing; I use my phone more than OWA.
Do you know which version of Exchange Server you're accessing?

Can not access CRM from outside the office network - Access denied You do not have sufficient access rights or privileges to perform this action.

Hi,
I can not access CRM from outside the office network - Access denied You do not have sufficient access rights or privileges to perform this action. I can access CRM with same user id and password from our office inside the network. I can get
the page to give login details once I have login details I got below error. Please help me to solve this issue. It was working before.
Access denied You do not have sufficient access rights or privileges to perform this action.
Regards,
Noushad
[email protected]

On Premise system Configured with AD FS server for claims-based authentication you need to update your host file with server url to access it from outside office network.
Refer
this on how to update host file.
Regards, Saad

I have been using thelatest ver firefox. Noe I can not access it. I receive the following message" Windows cannot access the specified device, path or file. You may not have appropriate permission to access. I am using windows XP ,

unable to access firefox. I receive the following message" Windows can not access the specified device, path or file. You may not have appropriate permission to access. I restored the system to an earlier date when I could access Firefox. I removed an re-installed firefox no changes.

Do a clean (re)install and delete the Firefox program folder (C:\Program Files\Mozilla Firefox\).
Download a fresh Firefox copy and save the file to the desktop.
*Firefox 13.0.x: http://www.mozilla.org/en-US/firefox/all.html
Uninstall your current Firefox version, if possible.
*Do NOT remove personal data when you uninstall your current Firefox version, because all profile folders will be removed and you will also lose your personal data like bookmarks and passwords from profiles of other Firefox versions.
Remove the Firefox program folder before installing that newly downloaded copy of the Firefox installer.
*It is important to delete the Firefox program folder to remove all the files and make sure that there are no problems with files that were leftover after uninstalling.
*http://kb.mozillazine.org/Uninstalling_Firefox
Your bookmarks and other profile data are stored elsewhere in the Firefox Profile Folder and won't be affected by a reinstall, but make sure that you do not select to remove personal data if you uninstall Firefox.
*http://kb.mozillazine.org/Profile_folder_-_Firefox
*http://kb.mozillazine.org/Profile_backup
*http://kb.mozillazine.org/Standard_diagnostic_-_Firefox#Clean_reinstall

I have a web site that I subscribe to and when I pulled it up Firefox asked me if I wanted to allow it or not. Accidently I pressed never allow for this site. Opps . . How do I undo this? I tried restarting and am now stuck as I can not access my website

I have a web site that I subscribe to and when I pulled it up Firefox asked me if I wanted to allow it or not. Accidently I pressed never allow for this site. Opps . . How do I undo this? I tried restarting and am now stuck as I can not access my website

Do you mean saving a password?
If you clicked "Never" then you have created an exception that you need to remove.
Remove site(s) from the Exceptions:
* Tools > Options > Security: Passwords: Exceptions
* https://support.mozilla.com/kb/Remembering+passwords

TS3798 I get this error message"your operation could not be completed" I need help figuring out why I can not access the web page.

I get this error message"your operation could not be completed" I need help figuring out why I can not access the web page.

amarilysfl wrote:
"Your disk could not be partitioned. An error occurred while partitioning the disk".
https://www.apple.com/support/bootcamp/
If you were using Apple's BootCamp and received this message, quit it and open Disk Uility in your Applicaitons/Utilities folder.
Select the Macintosh HD partition on the left and select Erase and Erase Free Space > Zero option and let it complete (important) this will check the spare space for bad sectors that can cause issues formatting partitions.
Once it's completed, try creating a partiton again in BootCamp.
If that doesn't work, then hold command option r keys down while connected to a fast internet connection, Internet Recovery should load (spinning globe) and then in that Disk Utility, select your entire internal drive and click > First Aid > Repair Disk and Permissions.
reboot and attempt Bootcamp again.
If you still get a error, it might be that you have OS X data on the bottom area where BootCamp partition needs to go. This would occur if you had the drive or computer for a long time or wrote a large amount of files to the drive and nearly filling it up and then reduced some, but it left traces in the area BootCamp needs to go.
To fix this
BootCamp: "This disc can not be partitioned/impossible to move files."
How to safely defrag a Mac's hard drive

Can not access in box or contacts from tiscali web mail when using firefox as browser

I can not access my in box or contacts list at my tiscali web mail when using firefox as my browser. I have been able up to a few days ago and I can access these when using internet explorer browser.

Thanks for the helpful solution!

Can not access DVR or program DVR to record via web or apps

I can not access my DVR remotely via a PC or via the apps. I get a message that says cannot connect to your DVR right now, try again later. It has been like this for weeks. I called tech and they reset all the boxes, the ONT, I removed the COAX etc. rebooted and cleared router. The box can be seen online though just not the DVR. Also, on screen caller id does not work and the fix application does not fix it either.

It seems like I lose web access to the DVR every week.
I either have to unplug the DVR or have Verizon send a reboot signal. Even that doesn't work every time. It is a really annoying and inconvenient problem.

Can not access Tiscali web mail account "undefined e-mails" message. This is after upgrading to version 5! Any solutions?

Can not access Tiscali web mail account "undefined e-mails" message. This is after upgrading to version 5! Any solutions?

Did it work in Firefox 4, or did you skip that version?

Can not access web interface: Linux: permission denied

Similar Messages

Maybe you are looking for