Cisco RM-1252G-A-K9 can't access web interface
I hope I am in the correct forum for this topic?
For some reason I cannot access the web interface in order to configure this device. I have it connected to a router (DHCP). The router assigns an IP Address and I can ping it. If I attempt to go to that IP Address in any web browser. the page cannot be displayed. I've reset it several times. I have 2 of these and same problem. Am I missing something obvious? I sure hope so...
Connecting to the Access Point Locally
If you need to configure the access point locally (without connecting it to a wired LAN), you can connect a PC to its console port by using a DB-9 to RJ-45 serial cable.
Follow these steps to open the CLI by connecting to the access point console port.
Step 1 Connect a nine-pin, female DB-9 to RJ-45 serial cable to the RJ-45 console port on the access point and to the COM port on the PC.
Step 2 Set up a terminal emulator on your PC to communicate with the access point. Use the following settings for the terminal emulator connection: 9600 baud, 8 data bits, no parity, 1 stop bit, and no flow control.
Assigning an IP Address Using the CLI
When you assign an IP address to the access point using the CLI, you must assign the address to the BVI. Beginning in a privileged EXEC mode, follow these steps to assign an IP address to the access point BVI using the console port:
Command
Purpose
Step 1
enable
Enter privileged EXEC mode.
Step 2
configure terminal
Enter global configuration mode.
Step 3
Interface bvi1
Enters interface configuration mode for the BVI.
Step 4
ip address address mask
Assigns an IP address and subnet mask address to the BVI.
Step 5
end
Return to privileged EXEC mode.
Similar Messages
-
For whatever reason I can telnet from another switch to the SG300 switch but not directly to the switch. I also can't access the web interface or ping the switch. Any help would be appreciated. Here is the running config
config-file-header
WasteWaterSG30010MPP
v1.3.5.58 / R750_NIK_1_35_647_358
CLI v1.0
set system mode switch
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end xxxxxxxxxxxxxxxxxxxxxxxx
vlan database
default-vlan vlan 2
exit
vlan database
vlan 2,75,200,999
exit
voice vlan id 200
voice vlan oui-table add ________
voice vlan oui-table add _phone_____________
voice vlan oui-table add ___________________
voice vlan oui-table add ______________
voice vlan oui-table add
voice vlan oui-table add ___________
voice vlan oui-table add ___
voice vlan oui-table add ______________
hostname WasteWaterSG30010MPP
line console
exec-timeout 0
exit
line telnet
password 382fda4a4a26e6637edac0eb8b8ba4581087d32d encrypted
exit
line console
password 382fda4a4a26e6637edac0eb8b8ba4581087d32d encrypted
exit
enable password level 15 encrypted 382fda4a4a26e6637edac0eb8b8ba4581087d32d
username admin password encrypted 382fda4a4a26e6637edac0eb8b8ba4581087d32d privi
lege 15
snmp-server location XXXXXXXX
snmp-server community String1 ro view Default
sntp server 172.16.2.1
ip telnet server
interface vlan 2
ip address 172.16.2.23 255.255.255.0
no ip address dhcp
interface gigabitethernet1
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport mode access
switchport access vlan 999
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type unknown
interface gigabitethernet2
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet3
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet4
storm-control broadcast enable
storm-control broadcast level 10
storm-control include-multicast
port security max 10
port security mode max-addresses
port security discard trap 60
spanning-tree portfast
switchport mode access
switchport access vlan 999
macro description ip_phone_desktop
!next command is internal.
macro auto smartport dynamic_type unknown
interface gigabitethernet5
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet6
spanning-tree portfast
switchport mode access
interface gigabitethernet7
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet8
spanning-tree portfast
switchport mode access
switchport access vlan 999
interface gigabitethernet9
spanning-tree link-type point-to-point
switchport trunk allowed vlan add 75,200,999
switchport trunk native vlan 2
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
interface gigabitethernet10
spanning-tree link-type point-to-point
switchport trunk allowed vlan add 75,200,999
switchport trunk native vlan 2
macro description switch
!next command is internal.
macro auto smartport dynamic_type switch
exitA member of which VLAN ID is that device from which you trying to reach that switch?
Is that device directly connected to switch WasteWaterSG30010MPP? If yes, to which port?
If you are connecting from different VLAN than VLAN2, are you using routing between VLANs? Where is that routing device connected to?
> I also have another switch that connects to the network through this switch and am able to telnet to it.
that second switch member of same VLAN 2? Or management is part of different VLAN?
..too few information to be able to give you final answer. -
Can not access web interface: Linux: permission denied
When starting my oracle-xe on centos5 it works but i can not open the web interface. During install i have configured it on port 81 and this is the error i get when starting the db:
30-MAY-2010 19:17:54 * (CONNECT_DATA=(CID=(PROGRAM=)(HOST=localhost.localdomain)(USER=oracle))(COMMAND=status)(ARGUMENTS=64)(SERVICE=LISTENER)(VERSION=169869568)) * status * 0
Error listening on: (Description=(Address=(Protocol=tcp)(Port=81)(Host=localhost))(Presentation=HTTP)(Session=RAW))
30-MAY-2010 19:17:57 * service_update * XE * 12546
TNS-12546: TNS:permission denied
TNS-12560: TNS:protocol adapter error
TNS-00516: Permission denied
Linux Error: 13: Permission deniedFirewall and seLinux are disbled.
I have installed oracle-xe as root and added root to the dba-group
What could be the issue for this?
Edited by: Yannick.O on May 30, 2010 10:35 AMYou have to use some port higher then 1024. Ports below 1024 are reserved for root user only.
-
Can I access Webi queries and Xcelsius dashboards from SAP portal?
Hello,
Can I access Webi queries and Xcelsius dashboards from SAP portal? And how?
ThanksPortal Part 1
/people/ingo.hilgefort/blog/2010/03/29/sap-businessobjects-enterprise-sap-enterprise-portal--part-1-of-4
Portal Part 2
/people/ingo.hilgefort/blog/2010/03/30/sap-businessobjects-enterprise-sap-enterprise-portal-part-2-of-4
Portal Part 3
/people/ingo.hilgefort/blog/2010/04/08/sap-businessobjects-enterprise-sap-enterprise-portal--part-3-of-4
Portal Part 4
/people/ingo.hilgefort/blog/2010/04/21/sap-businessobjects-enterprise-and-sap-enterprise-portal--part-4-of-4
Ingo -
How can i access web when i am connected through a proxy?
HI,
I am rakesh from bangalore. I want to know how can i access web when i am connected to internet throug a proxy. are there any classes to handle this in java.net package?
Thanking you
Rakeshthe URL class can also handle a proxyserver.
URL urlobj = new URL("http", proxyhost, proxyport, url); -
[12.1.1] Can't get web interface to work.
Hello,
This isn't a fresh install of EBS per se, but it isn't a production EBS system or anything like that. So it was originally installed in December or so, but we haven't really touched it since then. The only thing we use this server for is testing EBS functionality offered by our product. The point in telling you this is that I don't think the web interface ever worked, but since the application seems to be working fine, we never had a reason to fix it until now.
Today I'm trying to schedule some concurrent programs in EBS. Basically, I'm just looking to find out a bit about the concurrent manager scheduling options and how schedules are stored in the DB. As far as I know the only way to do this (schedule a conc. program to run, say, once a day) is through the web interface. If there's another way, I would love to hear it because I don't particularly care that the web interface isn't working besides the fact that I want to schedule a test concurrent program.
Note that I can't access the interface on the EBS box itself either.
Here are my request details:
GET http://oracleebs.advsyscon.com:8000/OA_HTML/AppsLogin HTTP/1.1
Accept: text/html, application/xhtml+xml, */*
Accept-Language: en-US
User-Agent: Mozilla/5.0 (compatible; MSIE 10.0; Windows NT 6.1; WOW64; Trident/6.0)
Accept-Encoding: gzip, deflate
Host: oracleebs.advsyscon.com:8000
DNT: 1
Connection: Keep-Alive
Cookie: oracle.uix=0^^GMT-5:00^p; __utma=252711254.678514999.1359557956.1359557956.1359557956.1; __kti=1306523819047,http%3A%2F%2Fwww.advsyscon.com%2F,; __ktv=f42d-f27d-cd94-651813032e35c2e; __hstc=252711254.fd397c917966433ca3ad39f9002e7bb0.1359557960441.1359557960441.1359557960441.2; hubspotutk=fd397c917966433ca3ad39f9002e7bb0
Here is the response I get:
HTTP/1.1 500 Internal Server Error
Date: Fri, 09 Aug 2013 14:49:57 GMT
Server: Oracle-Application-Server-10g/10.1.3.4.0 Oracle-HTTP-Server
Content-Length: 304
Connection: close
Content-Type: text/html
<HTML><HEAD><TITLE>500 Internal Server Error</TITLE></HEAD><BODY><H1>500 Internal Server Error</H1><PRE>Servlet error: An exception occurred. The current application deployment descriptors do not allow for including it in this response. Please consult the application log for details.</PRE></BODY></HTML>
This causes IE to give me a message like "The website cannot display the page. Most likely causes: The website is under maintenance. The website has a programming error."
"uname -a" on the EBS server:
Linux OracleEbs.domain.com 2.6.18-238.el5 #1 SMP Sun Dec 19 14:22:44 EST 2010 x86_64 x86_64 x86_64 GNU/Linux
AKA, this is a RedHat 5 system.
I tried looking at the error_log in Apache/Apache/logs, but it didn't seem to show anything (and it was from like, December 19).
Any ideas as to how to troubleshoot or fix this?
Thank you!Hi,
I'm just looking to find out a bit about the concurrent manager scheduling options and how schedules are stored in the DB. As far as I know the only way to do this (schedule a conc. program to run, say, once a day) is through the web interface. If there's another way, I would love to hear it because I don't particularly care that the web interface isn't working besides the fact that I want to schedule a test concurrent program.
Yes, you may schedule concurrent request from backend sql/plsql and this has been discussed in forum many a time, please refer:
https://forums.oracle.com/search.jspa?view=content&resultTypes=&dateRange=all&q=concurrent+request+backend&rankBy=relevance&contentType=all&containerType=&container=&containerName=&userID=&numResults=15
Also:
https://forums.oracle.com/thread/2160246
Hope this helps!
Best Regards, -
Cisco 4402 WLC IOS Upgradation using CLI and Web Interface
Hi,
I would like to know how to upgrade IOS of Cisco 4402 WireLess LAN Controller using CLI and Web interface ?
Can any one help me regarding the same.
Please answer as soon as possible.
Thanks in advance.Here are the instructions for upgrading the controllers via GUI:
http://www.cisco.com/en/US/docs/wireless/controller/release/notes/crn52.html#wp472449
Instructions via cli:
Cisco recommends that a direct CLI console port connection is used to update the controller software.
1. Make sure a TFTP server is available for the Operating System (OS) software download. Also, keep these guidelines in mind when the TFTP server is set up:
If a download is performed through the service port, the TFTP server must be on the same subnet as the service port because the service port is not routable.
If a download is performed through the Distribution System (DS) network port, the TFTP server can be on the same or a different subnet because the DS port is routable.
The TFTP server cannot run on the same computer as the Cisco Wireless Control System (WCS) because WCS and the TFTP server use the same communication port.
2. Download the desired OS software update file from the Cisco website to the default directory on the TFTP server.
3. Log into the WLC CLI.
4. Issue the ping server-ip-address command to verify that the WLC can contact the TFTP server.
5. Issue the transfer download start command and answer n when prompted to view the current download settings.
This example shows the command output:
transfer download start
Mode........................................... TFTP
Data Type...................................... Code
TFTP Server IP.................................
xxx.xxx.xxx.xxx
6. TFTP Path...................................... TFTP Filename.................................. AS_2000_3_0_x_x.aes --OR-- AS_4100_3_0_x_x.aes --OR-- AS_4400_3_0_x_x.aes Are you sure you want to start? (y/n) n Transfer Canceled Issue these commands to change the download settings:
* transfer download mode tftp
* transfer download datatype code
* transfer download serverip tftp-server-ip-address
* transfer download filename filename
* transfer download path absolute-tftp-server-path-to-file
Note: All TFTP servers require the full pathname. For example, in Windows, the path is C:\TFTP-Root. (In UNIX forward slashes (/) are required.)
7. Issue the transfer download start command to view the updated settings, and answer y when prompted to confirm the current download settings and start the OS code download.
This example shows the download command output:
transfer download start
Mode........................................... TFTP
Data Type...................................... Code
TFTP Server IP.................................
xxx.xxx.xxx.xxx
TFTP Path......................................
path>
TFTP Filename..................................
AS_2000_3_0_x_x.aes --OR--
AS_4100_3_0_x_x.aes --OR--
AS_4400_3_0_x_x.aes
Are you sure you want to start? (y/n) y
TFTP Code transfer starting.
TFTP receive complete... extracting components.
Writing new bootloader to flash.
Making backup copy of RTOS.
Writing new RTOS to flash.
Making backup copy of Code.
Writing new Code to flash.
TFTP File transfer operation completed successfully. Please
restart the switch (reset system) for update to complete.
8. The WLC now has the code update in active volatile RAM, but the reset system command must be issued to save the code update to non-volatile RAM (NVRAM) and reboot the WLC.
This is a sample output:
The system has unsaved changes.
Would you like to save them now? (y/n) y
The controller completes the bootup proce -
How can I access WEB-INF/lib
Hello all,
I deployed JClient application using Java Web Start.
I have the following lines in jnlp file
<resource>
<jar href="WEB-INF/lib/share.jar" />
</resource>
There's actually share.jar under WEB-INF/lib directory,
but I got error message when execute the application.
It seems that I can't access files under WEB-INF via http.
Does anybody know why?
Thanks in advance.Sorry for being picky on this. Oracle is not doing it, it is the software you're using, ie JDeveloper in your case.
AFAIK, the Servlet spec states that every library that is needed by the Servlet application should be put under WEB-INF/lib. These libraries are not accessible for any other usage.
JDev is doing this because your web application needs it.
If your JNLP application needs it too, JDev should be smart enough to include it twice in your WAR file, once for your web application and once for your JNLP application.
On the other hand I really hate software that is too smart and causes more problem by being smart than everything else.
Having said that, please file an enhancement request on Metalink for JDev for better library management for JNLP applications.
--olaf -
Can't access web after install
Installed on new SLES11 box. Livetime says it's running, but I can't access at http://<ip> or http://<ip>:8700.
When I installed SLES, I used the defaults for server type (Print). Show I add/change to Web/LAMP?
Or is it something else?
thanksLindsey,
It appears that in the past few days you have not received a response to your
posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Visit http://support.novell.com and search the knowledgebase and/or check all
the other self support options and support programs available.
- You could also try posting your message again. Make sure it is posted in the
correct newsgroup. (http://forums.novell.com)
Be sure to read the forum FAQ about what to expect in the way of responses:
http://forums.novell.com/faq.php
If this is a reply to a duplicate posting, please ignore and accept our apologies
and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://forums.novell.com/ -
How can i access web sites configured for internet explorer?
I try to access web sites thatwork with internet explorer from my mac and cannot load the home page. How can i access these pages?
Not sure if you're using a different browser than Safari. If not try Firefox or Chrome.
-
Can not access web wifi simble on but can not connect the the internet
wifi on but can not access internet
I COULD SOLVE THE PROBLEM!!! : CHANGE YOUR ISP
I it is obvious that we are talking about different issues, but all arise from the same origin. I am a surgeon and fortunately one of my patients is executive manager of one of biggest ISP companies from which I have bought my Internet service for home and my clinic.
One day I told him the problem and he promised to check it for me. A few days later he called me and discussed the exact problem (unfortunately as I am not I.T professional, I couldn’t understand it well, I can just remember he was talking about MULTIPLEXING incompatibility between Mac security settings and that specific ISP multiplexing settings, He also said they had similar problems with some Linux users. I can remember he relate the problem to cheap ISP hardware, which leads to security issues which are ignored by Windows Systems but leading to connection blockade in Mac Browsers. That’s why if you PING yahoo.com, you will see everything is OK but your browsers are not working)
In fact this is a hardware issue which is related to ISP (Internet Service Provider) security and not your Mac.
The day after, I took my MacBook to some ISP offices and asked them to let me connect to their line just for a test. “ Surprisingly I found out without changing my MacBook’s settings it works well with some ISPs and not with others!! “
I have two ADSL lines: one at home and one in my clinic. First I changed my home ISP and everything is well at home from the day I did the change. But before changing my clinic’s ISP it worked at home and not at the clinic. Later I changed my clinic’s ISP and afterward never I had any problem. This proves ( as that manager said also) this problem is related to ISP and not Mac itself and that’s why Apple could not have resolved the problem yet: different ISPs have different issues.
Here I can make some suggestions:
1- First, take your MacBook into different ISP offices and find the one which works well (before making the contract and paying money to the ISP, restart the Mac or send it into sleep mode repeatedly to make sure the connection never drops with restart or sleeps)
2- Change your modem: Modems as TP-LINK, D-LINK, are not well compatible with Mac. Apple modems or Linksys are perhaps the best choices (this is not main cause of internet drop, but can affect the performance)
3- Make sure your neighbor’s Wi-Fi is not exactly on the same channel as you are using (I use iStumbler for finding my neighbor’s channels)
4- Find best DNS: ask your ISP to provide you most compatible DNS’s for you. Perhaps most known DNSs are 8.8.8.8 and 4.2.2.4.It helps you to browse the Internet more efficiently
Some people in other forums suggested that upgrading to Mountain Lion has helped them. But It didn't work for my clinic's line. Just changing the ISP at clinic resolved my problem
BETWEEN THESE 4 SUGGESTIONS, THE FIRST ONE IS THE MAIN SOLUTION AND NO 2-4 CAN HELP THE PERFORMANCE.
Move on!!! Change your ISP and let me know if it works!!!! -
Can't access User Interface on WRT54G.
I can't access the user interface any more on my WRT54G. Used to be I could access it with IP 192.168.1.1 over my network, (or using the internet www.mydomain.com:8080) and it would come up but very, very slow. Now I can't access it at all. When I go to the address, the login box comes up, and once I enter the login, it just goes to a blank screen. I've tried multiple PCs, Firefox, IE. Nothing works. How can I fix this?
The router continues to work fine, and the LinkSys Advisor functions (slowly) I just can't access the admin user interface to make changes.Might be possible that the usernmae & password you are using is not working on the route ... make sure that you are using correct username & password .... if not then reset the router so that the password also gets resetted & you can use Admin password without any username ...
Once resetted you need to reconfigure the router ... .& open the port 8080 for remote access .... -
Safari Mac can't access web site that Windows can
None of my Macs can access the site http://cards.123greetings.com . I get Can't Find Server messages in both Safari and Firefox. (Clearing caches doesn't help)
cards.123greetings.com is part of a large free card site that did a major upgrade in October. It still renders correctly on a PC running Windows XP Home which runs on the same network as the Macs, so it's not an isp problem.
Since both Macs (G4 iBook running 10.3, MacBook running 10.4) have the same Can't Find Server problem with both Safari and Firefox, it appears that some setting in the Macs themselves is causing this.
Any help or insight would really be appreciated - Thanks!A big Thank You to Mulder for letting me know that you can access the site (with Mac Safari I presume) - That's good news.
The bad news: I still can't access the site.
The problem affects two separate computers and four browers. Taking your advice, I repaired permissions and logged in as a new account on both machines. Unfortunately that didn't work.
I next tried accessing the site on the MacBook through Parallels running Windows XP Home. The site came up fine using Internet Explorer.
Then I realized that Parallels operates with a different ip address. So I went back on the Mac using a proxy, and the site came right up.
It now seems that the ip addresses of both computers are being blocked at some level. I want to thank Mulder for replying and virtually ruling out that it might be a Safari issue. I'm now "off topic" and will no longer post in this section. But I'm also over my head... If anyone has advice about how to proceed now, I'd truly appreciate it.
Thanks! -
I am trying to access a web site that I normally have no problems accessing. Now Safari tells me:
Safari can't find the server
Safari can’t open the page “http://www.xxxx.edu/” because Safari can’t find the server “www.xxxx.edu”.
We are using an apple time capsule and no device on the wireless network can open the above web site. We asked a friend to log on and they had no problem accessing the web site.Hi,
Check Network pane in System Preferences. Select the Proxies tab.
If there are any boxes selected on the left, deselect then quit Safari. (Command + Q)
You can also access that information from System Preferences - Advanced. Click the *Change Settings* button.
Relaunch Safari.
Carolyn -
Can't access management interface via vpn connection
Hi all,
I can't seem to be able to manage my ASA 5510 when I connect via vpn. My asa sits at a remote colo, and from my office i can connect fine. I have it configured as management-access (dmz), bc as of now we are just doing some staging and all the servers are in the dmz interface.
When i connect with the vpn client, in the routes it sees 192.168.1.0 255.255.255.0 which is the management network/interface.
For some reason I can't get access to 192.168.1.1 to use the ASDM.
Here is how i did my vpn via CLI
isakmp enable outside
isakmp identity address
isakmp policy 10
authentication pre-share
encryption des
hash md5
group 2
lifetime 86400
ip local pool vpnpool 10.1.1.2-10.1.1.10
access-list split_tunnel standard permit 192.168.200.0 255.255.255.0
access-list split_tunnel standard permit 192.168.100.0 255.255.255.0
access-list split_tunnel standard permit 192.168.1.0 255.255.255.0
group-policy xxxxx internal
group-policy xxxxx attributes
dns value
split-tunnel-policy tunnelspecified
split-tunnel-network-list value split_tunnel
username xxxxx password
username xxxxxx attributes
vpn-group-policy xxxx
username xxxxxx password
username xxxxxx attributes
vpn-group-policy xxxx
username xxxx password
username xxxx attributes
vpn-group-policy xxxx
tunnel-group xxxx type ipsec-ra
tunnel-group xxxx general-attributes
address-pool vpnpool
tunnel-group xxxx ipsec-attributes
pre-shared-key
access-list vpnra permit ip 192.168.200.0 255.255.255.0 10.1.1.0 255.255.255.0
access-list vpnra permit ip 192.168.100.0 255.255.255.0 10.1.1.0 255.255.255.0
access-list vpnra permit ip 192.168.1.0 255.255.255.0 10.1.1.0 255.255.255.0
nat (inside) 0 access-list vpnra
nat (dmz) 0 access-list vpnra
nat (management) 0 access-list vprna
crypto ipsec transform-set md5des esp-des esp-md5-hmac
crypto dynamic-map dynomap 10 set transform-set md5des
crypto map vpnpeer 20 ipsec-isakmp dynamic dynomap
crypto map vpnpeer interface outside
Any help would be much appreciatedit seems like you are missing a line:
management-access "interface"
http://www.cisco.com/en/US/docs/security/asa/asa71/command/reference/m_711.html#wp1631964
Maybe you are looking for
-
VPN Problems ASA 5505 to 7206 Router MM_WAIT_MSG2
Hi Since I swapped a Pix Firewall for a Cisco ASA 5505 Firewall at one of our Sites the VPN Tunnel wont come up I'm getting this: asaXXXXX# sho crypto isakmp sa Active SA: 1 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during reke
-
Hp envy 4500 will not print from windows 8. Thinks it prints, but it doesn't.
Am trying to print from my Toshiba laptop running Windows 8 to my HP Envy 4500 wirelessly. Works fine from my ipad, works fine from my desktop and laptop running Windows 7. I have uninstalled and re-installed the printer driver 5 times. Printer is re
-
Button help with asp database in dreamweaver
Hey i have a page that has an iframe inside it with 2 menu's side by side with buttons in between to move items from one menu to another and i have them set with javascript to move back and forth works great only problem is its also supposed to updat
-
Date Format in Visual Studio Query Result Window
Most vendor tools let you change the date format to show datetime in its query results window. But .NET does not have this. The ability to change this should be in located in Tools|Options but its not there. Can it be added in the next release? ALTER
-
Multiple queue receivers with disjoint message selectors - portable?
Hi all, I was wondering whether an application that uses multiple queue receivers with disjoint message selectors would be portable across different JMS providers. I fear it's not - at least the spec clearly states that the implementation of message