Can't connect to 802.1x wireless network after upgrading

I have a year-old iPod Touch that I recently upgraded to iOS 6. I have no problems connecting to my home network, but since upgrading, I haven't been able to connect to the 802.1x wireless network at my job. When I try to connect, I get a spinning circle, but no actual connection. If I do nothing, it never times out, just keeps spinning.
I've tried resetting the network settings. I am able to login and accept the certificate, but I never get an IP address. I have access to the logs, so I checked and I'm authenticating successfully. I had no problems whatsoever prior to upgrading to 6.01, and I have no trouble accessing the network with other devices, including my MacBook Pro and MacBook Air.

If you restored to factory settings/new iPod and still have the problem that indicates a hardware problem.
Make an appointment at the Genius Bar of an Apple store..
Apple Retail Store - Genius Bar

Similar Messages

Can't connect to DET NSW wireless network after upgrading to mountain lion 10.8.2

Unable connect to DET(DER) NSW wirless network at school.
able to connect to wired network.
Takes too long to print wirless HP laser jet CP 1025

See http://applehelpwriter.com/2012/08/07/problems-with-wifi-safari-and-mountain-lio n/

MacBook can't see my home wireless network after upgrade to OSX 10.8.5

After upgrading to OSX 10.8.5, my MacBook does not detect any wireless nertworks. My iPad and iPhone work fine, my router has been rebooted, WiFi is turned on, and the ethernet connection is how I am writing this message to you via broadband. There are a half dozen wireless networks in range (according to my iPhone) but the MacBook cannot find the router I am sitting next to. Any ideas on how to correct this issue?

It appears an SMC reset was required:
HT5815 I've just done the 10.8.5 update on my MacBook Pro end of 2008, and WiFi don't work after reboot... Impossible to activate it...
Here is your other post: MacBook can't see my home wireless network after upgrade to OSX 10.8.5
If you reply to it and marked it "solved", perhaps with a link to that post (copy and paste it, or just say you performed the SMC reset) it will help others find a solution. Thanks!

Can't connect AE to existing wireless network

I can't get my AE to connect to my existing wireless network. I saw the other thread on this and followed those steps, but it didn't work. Here's what I did:
1. Connected the AE to my D-Link DIR-655 wireless router via ethernet cable.
2. Opened Airport Utility and established a connection to the AE.
3. Renamed the AE and entered a password.
4. In the "wireless" tab, I selected "join existing network", chose my wireless network, selected the security type (WPA Personal) and entered the password.
5. In the "music" tab, I named the speakers and entered a password.
So far so good. I clicked "update" and the AE restarted. After a while I received an error message informing me that the base station could no longer be detected. According to the directions posted in the other thread, this is actually supposed to be a sign that the AE is now in client mode and all is well.
I unplugged the ethernet cable from the AE and router and then went to the other room. I plugged the AE into the speakers and then plugged the AE into the wall.
However, instead of a green light all I have is a flashing amber light, even after several minutes. No connection.
I reset the AE and repeated the steps above, to no avail. Still a flashing amber light.
Any ideas?

I'm having a similar issue. My AE is connected directly to a Netgear WGR614v4 router, and I run through all the steps you mentioned. When I choose to update the settings to the AE, I get the same "error" you mentioned about the AE not being found, and I also took that as a sign that I'm in client mode. I moved the AE to the other room, connected my mini cable to the stereo, then plugged the AE back into the wall. The AE runs through its setup and eventually gets a solid green light, so I'm thinking all is well.
The problem is that I then log back into the AirPort Utility on my laptop and the AE is not shown in the top left like it should be. After doing a bit of reading, I've figured out that I can manually find it by going to File>Configure Other and entering the AE's IP address and password. Then I get a window showing the details of the AE, its name, network, encryption, etc. However, if I close this window, it still doesn't show up in the main AirPort Utility screen and I'm not sure how to configure it for AirTunes.
Hoping that's just a bug with the AirPort Utility software, I open up iTunes to see if I can locate it there. I know I should see a pulldown menu at the bottom of iTunes that gives me an option for AE as my audio output method, but the menu is not there. Now I'm completely stuck.
At this point I decide to start from scratch, so I do a Factory Default reset by pressing down the reset button on the AE as I plug it into the wall. Now it is supposedly reset, so I plug it back into my router, then it runs through a setup sequence and lights up solid green before I've even done anything. It shows up in AirPort Utility with a default base station ID, but my computer won't connect to it at all. I'm hoping I can try to reset it again this evening and at least get back to the normal setup screen, but I'm really not sure what I could do differently at this point.
This is frustrating and I'm on the verge of giving up, but I REALLY want this to work out.

Can't connect to an public wireless network

Hello,
I'm having trouble connecting to my college's wireless network. I've connected to it before. It loads a sign in page for you to login with your school ID . Since last week, I can see the network in my airport with full bars. The login page does not load and it says im not connected to the Internet. I've also put in the login page URL but that does not load either. The college's IT guy says he has seen this problems many times with macs this semester only. He said it might had been affected by a recent update.
I can connect to my wireless network at my house and also at my parents so I don't understand why I can't connect! Also , the login page loads on my iPhone.
Thanks to anyone with any answers!

I have talked to other Mac and window users who were online.. So I'm not sure why I can't connect! The tech guy told me to make sure that my mac wasnt remembering my wifi settings

Can't connect to school's wireless network

I'm living in residence at Laurier University, and I can't get my touch to connect to the internet. With our computers, we had to connect to our laurierdownload network first, download a program and then change some settings in order to connect to the laurierwireless network.
I can connect to laurierdownload, but I don't know how to download the program and change the settings. Sometimes, laurierwireless will show up, but when I try to connect to that, and type in my username and password- the same that I always use for the network on my laptop- it says it's wrong.
Does anyone have any idea how I can connect to the network?
PS: Here's the info on how to connect to the network. This is all the stuff I can't manage to figure out on my ipod:
http://www.wlu.ca/page.php?grp_id=47&p=9474
Thanks!
~Jessica

Laurierwireless is an 802.1X authenticated network and there have been problems reported here with accessing 802.1X networks.
IPhone and iPod touches with software 2.0 and later are supposed to support 802.1X. However getting it to work may require help from your schools IT department. See http://www.apple.com/iphone/enterprise/integration.html
Good luck.

Can't connect Time Capsule to wireless network...

I was able to backup my computer with Time Capsule if the computer and Time Capsule are connect with the internet cable. But then when I unhook the computer, it can't connect wirelessly. If I look in my available wireless networks, I do find the TIme Capsule network, but then I try to connect, it won't connect. I need some help connecting to that network so I can backup wirelessly!

If the computer can see the wireless network, connection issues can be poor signal or interference.
Wrong previous setup on the airport .. go into the network preferences for the airport and see if it is getting an IP address.. if it fails make sure the setting is correct.
Plug back in by ethernet and redo the wireless setup of the TC.
Use SMB type names.. Short, no spaces pure alphanumeric.
Use Fixed radio channels.. try in turn 1, 6, 11 (13 outside US) These are the only non-overlapping channels.
Use no security at all for testing.. but then WPA2 Personal is the only security rated for N wireless connections.
I recommend also giving a different name to 5ghz so you can force connection to the faster network.
If you still have issue change the mode of the wireless.. there are various manual options..
The idea is to reduce all auto settings so you can be sure it will work.
If you are on Lion or even Mountain Lion use the v5 utility. There are ways and means to install the later.

Can't connect printer to my wireless network

I am running Windows 8.1. Had HP Officejet 4620 and just bought a new HP Photosmart 7520. I can't connect either to wireless network. My Dell laptop is connected to my apartments wifi so I do not have a router. When I display my printer info it shows correct wifi name and gives an IP address with a strong signal.
when I print the network configuration page it shows I am connected. Help!!!!! I am currently connected by USB cable.

Hi Bob1948
I would be happy to help you.
I understand you aren't able to connect to the wireless network but you can print by a usb connection.
If you upgraded to Win8.1, then I would uninstall and reinstall the software again to get it to work.
Photosmart 7520 drivers.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4157&lc=en&cc=us&dlc=en&sw_lang=&product=5199...
Officejet 4620 drivers.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4158&lc=en&cc=us&dlc=en&sw_lang=&product=5191...
If the computer already had Win8.1 then I would recommend to power cycle the router and the computer. Turn the computer off. Disconnect the routers power cable, wait 10 seconds, then reconnect the power cable. Wait till it's ready. Then turn the computer back on again.
Try it now.
Here is a url for Printer Does Not Maintain Wireless Connection.
http://h10025.www1.hp.com/ewfrf/wc/document?docname=c03381908&tmp_task=solveCategory&cc=us&dlc=en&la...
If you need more assistance just let me know.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos Thumbs Up" on the right to say “Thanks” for helping!
Gemini02
I work on behalf of HP

Can't connect PowerBook G4 to wireless network

My wife has brought home a PowerBook G4 from work. It cannot connect to my wireless network. I use a D-Link router. Airport shows full bars, but it does not connect. I was able to connect by plugging it in to ethernet cord. Is there something with this model that has to be changed to have it recognize a wireless connection?

I am having a somewhat similar problem with my PB. I am trying to connect to a brand new (2 weeks old) Netgear wireless router. When the security password protection is turned off I am able to connect without issue. Sadly, it is a shared connection, and security needs to be on. When the password function is on, I am unable to connect. I repeatedly get a message saying "there was an error joining the airport network __."
The password is correct. The signal from the router has been switched to "mixed", per "gobnay's" previous suggestion. And I am getting enough signal strength from the router. It is set to WPA Personal, and other Mac's (a newer MacBook Air, and MacBook) have had no problems connecting. Mine is an older model, PB G4 running 10.4.11 (hardware circa 2003). It seems to be a security problem, but I am otherwise stumped...

Can't connect to computer through wireless network

I recently purchased a Powerbook G4 with OS X Server 10.4.6 installed, and I cannot connect to my iMac G5, which has OS X 10.4.6 installed. I am trying to connect them wirelessly, and it sees the G5, but tells me that it is offline and can't connect when I try. I can connect to the Powerbook through the iMac, but not the other way around. Tried different share settings on G4, but am quite unfamiliar with OS X Server. Any help would be appreciated.
Thanks.

It seems like you may not have the relevant service(s) enabled in Sharing preferences on your iMac, if I understand your problem correctly. The settings on the server, other than firewall, shouldn't matter for outgoing connections.

No longer able to connect and use internet on any wireless network after upgrading to iOS 6

Everything worked great for the first few hours. But now whenever I connect to ANY wireless network on my iPad, it connects fine.. When I do anything that involves internet, the wifi logo goes away, and a screen pops up (as if you're using a hotel wireless network) and says "apple - page not found" at the top, and is an apple.com page. Even though there is no wireless symbol in the upper left corner, I can go to all of the links and everything, but outside of this one window the internet no longer works.
I have NEVER seen anything like this before.
I didn't do anything abnormal that would have caused this.
Thank you.

Hi there KAP1973,
You may find the information in the article below helpful.
iOS: Troubleshooting Wi-Fi networks and connections
http://support.apple.com/kb/TS1398
iOS and OS X: Recommended settings for Wi-Fi routers and access points
http://support.apple.com/kb/ht4199
-Griff W.

IPhone not connecting to WEP 128 Wireless network after 1.0.2 upgrade

Hello all,
I have the iphone since the last week. I was pretty happy with it until I upgraded the iphone to version 1.0.2.
From that very moment, the WEP Hex/ASCII Key option dissapeared when setting a connection to a wireless network. Mine was working with 1.0.0 and now it does not work.
I am Telecom engineer, and I pretty sure everything is correct. Mi 128 wep key is 13 characters long and (of course) 26 HEX long.
I have tried putting " before and after the ASCII key and also entering a $ sign before the HEX key.
I have also disabled the Auto caps, just in case.
After all this testing and a quick look at google, it seems that there are more people with the same problem.
Could anyone say to me if there is any other way? Or if apple is gonna release a new version with this issue fixed?
I am quite dissapointed.
BTW: I have tried all the stuff of reseting the router and "forget setting", etc.
BTW2: To switch to WPA may be an option in my network by it is no way a solution as the majority of the public AP use WEP....

I am using a Linksys BEFW11S4 and I've tried to make the WEP key work on and off for the last 2 months while tapping into other people's wifi to get by without it.
Previously, when I chose someone else's secured network from the 'available networks' list, it would open a window and ask for password. But if I selected my own secured network it wouldn't and would just say "unable to join XYZ network".
Here is what I did tonight and I'm not sure which step did the trick, but it's worth a try:
1 - On the router, I went into the Password tab and entered a password. Previously I hadn't been using any.
2 - On the iPhone, I clicked on the little arrow next to my network's name. In the following screen entered the DNS address of my router (on Linksys the address is found on the Status tab).
I now have it connected to my network. I disconnected and reconnected again without having to enter the password, so either it's saving the password someplace or it's the DNS address that did the trick. The iPhone MAC Address shows up in the DHCP Active IP Table of the router and the router is still WEP protected.
I hope this wasn't too confusing. If you reply, please tell me how you feel about the $200 price drop today!

Can't connect to the Hyper-V manager after upgrading to Windows Hyper-V 2012 R2

I have some Hyper-V server based on the free version (Windows Hyper-V 2012). I want to upgrade to the new version (Windows Hyper-V 2012 R2). So I begin to test it with
an already working server (aka I was able to totally manager the server remotely without problem) and so upgrade it to the R2.
After the upgrade, remote management and Hyper-V manager does not work anymore. So I redo my usual configuration steps (enable remote management, open firewall, uses
latest hvremote.wsf, etc.). I was able to regain access to Computer Manager but not the Hyper-V manager which still can't connect at all. I can't access the Task Scheduler too without having a lot of XML error like "The task XML contains a value which
is incorrectly formatted or out of range" (see below for screenshot).
Is there a new step to do to be able to manage Hyper-V 2012 R2 from a Windows 7 computer?
It's not a network problem as I can access RDP and MMC Computer Manager.
To be sure the problem is coming from the R2, I have taken an old computer, install Windows Hyper-V 2012, do my usual configuration step, and
tada: it works perfectly. I can access the Hyper-V manager from my client.
Technical details:
- Client is a Windows 7 SP1 x64 English member of a domain with latest RSAT (Windows6.1-KB958830-x64-RefreshPkg.msu).
- Servers are in a workgroup (not a domain's member). And no, I can't add them to the same domain as the client.

HI,
Can we upgrade HyperV 2012 to hyper v 2012 R2.
Thanks
Atul

Hi I can not connect to iTunes Store in iphone after upgrade of iO6. What should I do now ???

After upgrade I can not open application store or iTunes Store it's coming error can not connect to iTunes Store what should I do ?

Apparently when I updated my software this morning it logged me off my Wifi for some reason (even though the wifi icon at the top of the screen indicated it was using it), I logged back in and could connect.

Can't connect my iPad to my iMac after upgrade!

I upgraded my iPad Air to the iOS 8.0.2 yesterday, and after I did, I can't connect it to my iMac. When i try, with USB cable, it just jumps between being connected and not being connected.
I didn't have this problems before the upgrade on my iPad.... Can someone help me please?

Do you have the latest computer iTunes 11.4?
If you don't you can download it here below
Download iTunes Get the latest version of iTunes for Mac or Windows. Download now
If still no joy, try troubleshoot below
iOS: Device not recognised in iTunes
Mac: http://support.apple.com/kb/TS1591

Can't connect to 802.1x wireless network after upgrading

Similar Messages

Maybe you are looking for