Can't create a new password in WRT54GS wireless router

I'm trying to configure my Wireless router WRT54GS and i'm facing troubles with the passwords. When I insert a new password and the user name and password of my DSL ISP, the program accept it, gives me a message that says that the changes were made with success, but when it returns to the configuration screen, there are 15 black dots in the password field and, of course, I don't get a connection.(My passord has only 7 positions.) I've done all that I know to fix it, but the problems always come back. I've pressed the reset button already too. Many times. Someone would help me? Wlademir Mendes Brazil

well....the elongated password is not a worry .. as the password you enter is encrypted by the router .. therefore a long password
did you try entering the username as the complete email add like [email protected] ??
also, ensure that the DSL modem in in bridge mode ...

Similar Messages

How can i create a new password?

I forgot my password, how can i create a new one?

On Lion or Mountain Lion, you use the following technique to reset the Administrators password:
Boot to your Recovery Partition, by holding down the Option key while starting, and then selecting the Recovery HD as the boot choice.
Once booted, at the top of the screen is a menu ..., select Utilities / Terminal from the menu bar.
In the Terminal window, type “resetpassword” (without the quotes) and press return. A “Reset Password” window will open. Select your boot volume (your SSD drive) if it is not already selected. Select your administrators username from the menu labeled “Select the user account” if it is not already selected. Follow the prompts to reset the password. Restart the computer from the apple menu.

It wants to verify my account and won't take the password, how can I create a new one or verify the existing one?

I cloud wants to verify my account and won't take the password, how can I create a new one or verify the one it won't take?

If you can't remember the password, reset it at...
iForgot.com

I cannot recover my Master Password under 10.6.8. I want to change it. I do have my admin password for my account. How can I create a new master pw?

I cannot recover my Master Password under 10.6.8. I want to change it. I do have my admin password for my account. How can I create a new master pw?

If you are referring the Master Password that can be set in System Preferences>Security>FileVault, then see this thread:
How to reset FileVault master password
http://discussions.apple.com/thread.jspa?messageID=5822772
As explained there, and for obvious security reasons, a new master password created in this fashion way will not unlock any pre-existing FileVault accounts. Resetting the master password is therefore only useful after you turn off FileVault in all existing accounts. You can then turn FileVault back on after the new master password is in place.

How can i resset and create a new password cause i forgot my password and i can't connect anymore?

how can I get a new password because I forgot my password

connect the iPod to your syncing computer and restore it via iTunes. If it asks for the unknown passcode, place the iPod in recovery mode and then restore it. For recovery mode see:
iPhone and iPod touch: Unable to update or restore

IPad2 and a new MacBook running Lion, Both Devices use the same Apple ID which is a Hotmail eMail id. Can I create a new iCloud eMail Id and use iCloud eMail and continue to use my Hotmail Id for my Apple Id and use it for iTunes, iCloud

I have an iPad2 and a new MacBook running Mountain Lion. Both Devices use the same Apple ID which is a Hotmail eMail id. Can I create a new iCloud eMail Id and use iCloud eMail and continue to use my current Hotmail Id for my Apple Id for iTunes, iCloud.
Note, I will use both Hotmail and iCloud eMail.

Welcome to the Apple Community.
In order to change your Apple ID or password for your iCloud account on your iOS device, you need to delete the account from your iOS device first, then add it back using your updated details. (Settings > iCloud, scroll down and hit "Delete Account")

I am trying to install a Canon Pixma MG8220 which requires my Airport Extreme password. I do no know it. I then went to default Airport settings and renamed my network, but Airport required my password. How do I create a new password?

How do I create a new password for my Airport Extreme if I do not know the old password?

If you have the Mac that you used to configure the AirPort Extreme originally, you may be able to retrieve the password from KeyChain Access.
See this User Tip from forum expert Tesserax:
AirPort - Regain Access from Forgotten Passwords
If still no luck, you can reset the passwords again. Pay very close attention to the information about a Soft Reset in this Apple support document:
Resetting an AirPort Base Station or Time Capsule FAQ

I can not create a new user account on eprint

i can not create a new user account on eprint. I have been trying for over an hour and it repeats telling me that my email addresses are not entered correctly, however they match. ?

I have tried to create an account via ePrintCenter and it seems that the published application has several flaws in interpreting the provided input.
1) In the Filed for last Name I enter my last name, which consist of only Alph Characters. The form however thinks that there is some sort of special character and rejects my Input.
2) E-Mail address. is not identical; OK, so I do a quick OCR on the E-Mail and guess what they are identical. Again the form Fails to recognize this.
3) Enter a password (2 Fields) and a third is displayed which is marked as "*required" but is not labeled as to what the required info could possibly be. Or is it a 3 password confirmation box, who knows.
All I know is that a simple registration is a major pain with this HP site.
Any Help as to how to alleviate this would of course be greatly appreciated.

How do you allow a user to create a new password?

The way i have it set up right now the users are registered by the admin and a random password is provided for them to log in. When they login they're instructed to create a new password.
They click to update their information. Included in this form is an "Old Password" field and a "New Password" field. They can choose if they want to create a new one or not. So I don't want to make it a requirement.
1 - How do I validate the old password.
2 - When they type the new password and submit the update info form. It inserts the new record over the old. But only after confirming that that old password is correct. How is this done?
Or should they just type in a new password with no validation that they know the old. ? Hm.
Please let me know. Thank you.
Eddie Adolf

Hi frunsel,
if the user choose a name where already exist, the error throws out, but it clears all the register fields (all the users entrys, and i have a few fields)
humm, that´s not cool -- however...
how can i prevent this?
In this case I suggest providing a separate "check username availabilty" procedure in a blank window
(or a popup window, if you prefer) which ...
a) on page 1 has a form with one "check_username" text field, and on...
b) page 2 queries the login table´s "username" column against the textfield´s value and returns "username available" when no matching records were found, respectively "username already allocated" in case of a match.
That´s something I´d do without using ADDT, means DW´s native database related functionality are absolutely sufficient for such simple stuff
Cheers,
Günter Schenk
Adobe Community Expert, Dreamweaver

How can I create a new TC backup with ethernet, so I don't have to wait two days for a new wireless backup?

How can I create a new TC backup with ethernet, so I don't have to wait two days for a new wireless backup?
Several times in the last year, I've gotten a message that Time Machine needs to completely redo my backup. Using the wireless connection, this takes almost two days. Is there a way to do the backup with ethernet and then switch back to wireless? Thanks.

May I know what is needed to make sure the MacBook is able to see Time Capsule on ethernet?
Connect an Ethernet cable from one of the LAN <-> ports on the 2Wire gateway to the WAN port (circle of dots icon) on the Time Capsule.
If AirPort Utility cannot "see" the Time Capsule now, you will need to perform a "hard reset" by holding in the reset button for 7-8 seconds or so and then reconfigure the Time Capsule. You can use the same Time Capsule name and password, etc. as before.
Configure the Time Capsule to "Create a wireless network" and select the Bridge Mode option when it appears during the setup using AirPort Utility.
Once the Time Capsule is configured, restart the entire network again. Power down everything, start the 2Wire first and then start each other device after that one at a time about a minute apart.
Now you can connect your Mac directly to one of the LAN <-> ports on the Time Capsule for the backup using another Ethernet cable. In general, about 20-25 GB per hour will transfer.
The Time Capsule will broadcast a much faster wireless network than the 2Wire can provide, so you might want to leave the setup "as is" for awhile after the first backup is complete. If you decide to use the Time Capsule as your main wireless access point, you would want to turn the wireless off on the 2Wire since two wireless networks in close proximity can create interference problems.
Or, if you want to use the wireless on the 2Wire, you could turn off the wireless on the Time Capsule. Then backups will occur over the 2Wire wireless, or over Ethernet.
I don't really recommend the "Join a wireless network" setting on the Time Capsule for most users, but you could go back to that setup as well if you want after the first backup is complete.

How can i create a new Adminstrator user account ?

How can i create a new Adminstrator user account ?

Go to the System Preferences>Users.
Click the lock if and enter your password, if necessary.
Then click on the "+" symbol below the accounts list.
From the "New Account" menu, select"Administrator" and fill in the rest of the information.
And finally click the "Create Account" button.
Done. A new Administrator user account.

How can i create a new user with only read rights ?

How can i create a new user with only read rights ?

You are asking about a Database User I hope.
You can look into the Oracle 8i Documentation and find various privillages listed.
In particular, you may find:
Chapter 27 Privileges, Roles, and Security Policies
an intresting chapter.
You may want to do this with the various tools included with 8i - including the
Oracle DBA Studio - expand the Security node and you can create USERS and ROLES.
Or use SQL*Plus. To create a
user / password named John / Smith, you would login to SQL*Plus as System/manager (or other) and type in:
Create user John identified by Smith;
Grant CONNECT to John;
Grant SELECT ANY TABLE to John;
commit;
There is much more you can do
depending on your needs.
Please read the documentation.
-John
null

Can I create a login/password protection in Muse for a HTML5 page or two?

Hi,
I'm new to Muse. Can I create a login/password protection for
one of my pages in Muse?
thanks,

PASSWORD PROTECTING A PAGE WITH A NICE BOX DESIGNED INTO YOUR PAGE
FINALLY, I'VE FOUND AN ANSWER TO PASSWORDING A PAGE OR SECTION WITH ADOBE MUSE WITH GREAT SIMPLICITY AND ALLOWING YOU TO 'DESIGN' THE PASSWORD BOX INTO YOUR PAGE!!!
Even better is that you don't HAVE to have username AND password (although you could if you wanted to), so just a simple PASSWORD box and enter button DESIGNED BY YOU WITHIN YOUR PAGE, rather than nasty popups etc. Importantly, the password itself is NOT within the source code of your page either!!
The solution is at Jotform.com. I believe you can do this with a FREE ACCOUNT, although it's SUCH a great service for Musers that I paid for a proper account.
Before you do this, create a page on your site saying "Wrong Password. Please go away" or something to that effect. You'll need it for when they enter the wrong password.
So, in Jotform, you just create a new form and:
1. Drag on a password box (it's in the power tools section)
2. Select it and go to Conditions
3. Go to Change Thank You URL after submission
4. Enter: If [name of your password box] field EQUALS TO [enter your password]
5. In the "Then redirect to" box, enter the URL of your protected page and click save
6. In the resulting box click "ADD A NEW CONDITION" and do the SAME as stets 3 to 5 but this time say NOT EQUALS TO" with your same password and in the "Then redirect to" box, enter the URL of your WRONG PASSWORD page and click save
7. Embed the button on your page and you're done!!!
If you want to mess about with the EXACT alignment of a right aligned button and text box, you can go to Preferences and in the box which allows you to add your own custom CSS, enter the following code and mess about with the values until it's perfect for you:
.form-buttons-wrapper { padding-top:3px !important; }#id_2 {margin-left: -50px !important;}
Here's an example, built in Muse: www.hileytv.com/about.html
I hope this helps my fellow Musers!
Marcus

Hi folks, you might know how to fix this: my wifi shows (no hardware installed) then I went to system preferences and deleted the wifi connection, I went also to system information and I can not see wifi listed on Network, how can I create a new wifi ?

Hi folks, you might know how to fix this: my wifi shows (no hardware installed) then I went to system preferences and deleted the wifi connection, I went also to system information and I can not see wifi listed on Network, how can I create a new wifi or simply solve this, I have tryied shotdown pressing keys like P and R, option, etc. Please help me .

Please read this whole message before doing anything.
This procedure is a diagnostic test. It’s unlikely to solve your problem. Don’t be disappointed when you find that nothing has changed after you complete it.
The purpose of the test is to determine whether the problem is caused by third-party software that loads automatically at startup or login, by a peripheral device, by a font conflict, or by corruption of the file system or of certain system caches.
Disconnect all wired peripherals except those needed for the test, and remove all aftermarket expansion cards, if applicable. Start up in safe mode and log in to the account with the problem. You must hold down the shift key twice: once when you turn on the computer, and again when you log in.
Note: If FileVault is enabled, or if a firmware password is set, or if the startup volume is a Fusion Drive or a software RAID, you can’t do this. Ask for further instructions.
Safe mode is much slower to start up and run than normal, with limited graphics performance, and some things won’t work at all, including sound output on certain models. The next normal startup may also be somewhat slow.
The login screen appears even if you usually login automatically. You must know your login password in order to log in. If you’ve forgotten the password, you will need to reset it before you begin.
Test while in safe mode. Same problem?
After testing, restart as usual (not in safe mode) and verify that you still have the problem. Post the results of the test.

The installer can't create the new filder "/var/folders/kt/

Hello everyone, I'm not so sure if am posting this in the right place!!
I'm seeking help with this issue i encountered after installing and reinstalling MAMP, trying to set the root password for MAMP, which never worked, hence i continue uninstalling and reinstalling MAMP, couple more times, however one point in time it gave me this erorr:
There were error with the installation. You may want to try i
The installation failed.
The installer can’t create the new filder “/var/folders/kt/8g6g2k2j5x1_fn32rj475x640000gn/T//install.
335ftMWP5”.
I have erorr for over one week and I try to move on, or install MAMP!!
Thanks, any sugestion would help!!

Launch the Terminal application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ If you’re running Mac OS X 10.7 or later, open LaunchPad. Click Utilities, then Terminal in the page that opens.
Drag or copy — do not type — the following line into the Terminal window, then press return:
ls -Odel $TMPDIR
Post any lines of output that appear below what you entered — the text, please, not a screenshot.

Can't create a new password in WRT54GS wireless router

Similar Messages

Maybe you are looking for