Can't get PCI VXI card to initialize on CentOS 5 (Fedora Core 5)

Question

I am trying to configure a pci-vxi card on our new machine. We have an Intel MB (DG965WH) and the Q6600 Core2 Quad processor. The OS is CentOS 5 (Fedora Core 5) with kernel 2.6.18-53.1.4.el5.
I have read all the other posts concerning Fedora Core 5 and have modified the source code to fix the compile errors in the driver. The following lists the output I am getting:
when running make:
make -C /lib/modules/2.6.18-53.1.4.el5/build SUBDIRS=/usr/local/nivxi/src KBUILD_VERBOSE=0 modules
make[1]: Entering directory `/usr/src/kernels/2.6.18-53.1.4.el5-i686'
  CC [M]  /usr/local/nivxi/src/vxi.o
  CC [M]  /usr/local/nivxi/src/vxi_kernel.o
  CC [M]  /usr/local/nivxi/src/pci_io.o
  CC [M]  /usr/local/nivxi/src/mutex.o
  CC [M]  /usr/local/nivxi/src/vxiTimer.o
  LD [M]  /usr/local/nivxi/src/vximod.o
  Building modules, stage 2.
  MODPOST
WARNING: could not find /usr/local/nivxi/src/.nivxi.o.cmd for /usr/local/nivxi/src/nivxi.o
  CC      /usr/local/nivxi/src/vximod.mod.o
  LD [M]  /usr/local/nivxi/src/vximod.ko
make[1]: Leaving directory `/usr/src/kernels/2.6.18-53.1.4.el5-i686'
Kernel module built successfully and placed in ../sys/
Use /usr/local/nivxi/src/../sys/load_vxi to load it.
When running load_vxi:
NI-VXI device driver located in "/usr/local/nivxi/sys"
When running vxiinit:
Unable to initialize hardware
dmesg output:
VXI: initialized
[drm] Initialized drm 1.0.1 20051102
ACPI: PCI Interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 177
[drm] Initialized i915 1.8.0 20060929 on minor 0
VXI: unloaded
VXI: initialized
From /var/log/messages:
Dec 21 09:55:02 lion kernel: VXI: unloaded
Dec 21 09:55:07 lion kernel: VXI: initialized
No matter what I do I cannot get vxiinit to initialize the device. The device itself is listed
in the /dev directory as vxi0 where "0" is the number zero. On another machine we have
running CentOS 4.5 the device is listed as vxiO. where "O" is the capital letter O. The
device works fine on this machine.
I am not sure what I should try next. Any suggestions would be greatly appreciated.
Thanks,
Greg

Answer 1

Howdy Greg,
I've been researching your issue extensively over the past day and unfortunately
found your Fedora distribution has not been officially tested and verified for
functionality (assuming you're using a MXI 2, check out the VIX for Linux page).  That
being said, I was able to find some other Discussion Forum posts dealing with
hacking VXI to work on Fedora.  I know you said you read up on this, but I
wanted to post them anyways just in case. 
VXI
Drivers on Fedora Core 5
- This is quite a long post dealing with similar errors to
what you are seeing
NI-VXI for Linux Hangs on SMP/Hyperthreaded Machines with APIC
Enabled
- A KnowledgeBase article linked in the previous thread
Fedora
Core 5 - kernel 2.6.20 -NIKAL 1.5 How To
- This one is kind of a long shot since it's for our MultifunctionDAQ drivers
and not VXI, but check it out anyways to see if it gives you any ideas.
Let me know how these worked for you and if you have any
follow up questions.  Good luck.
Sincerely,
Chris G in AE
Sincerely,
Chris G in AE