Cannot accese setup site
Hey guys,Im using a WRT160n and im haveing trouble accesing the setup site.When i try and enter the defualt username and password the window pops up again saying its the wrong username and password.I havent even accesed the routers settings so i know its not changed.
Help?
Some stores sell routers that others have returned. You should not assume that your router was set to factory defaults when you purchased it.
You need to reset the router to factory defaults.
To reset your router to factory defaults, use the following procedure:
1) Power down all computers, the router, and the modem, and unplug them from the wall.
2) Disconnect all wires from the router.
3) Power up the router and allow it to fully boot (1-2 minutes).
4) Press and hold the reset button for 30 seconds, then release it, then let the router reset and reboot (2-3 minutes).
5) Power down the router.
6) Connect one computer by wire to port 1 on the router (NOT to the internet port).
7) Power up the router and allow it to fully boot (1-2 minutes).
8) Power up the computer (if the computer has a wireless card, make sure it is off).
9) Try to ping the router. To do this, click the "Start" button > All Programs > Accessories > Command Prompt. A black DOS box will appear. Enter the following: "ping 192.168.1.1" (no quotes), and hit the Enter key. You will see 3 or 4 lines that start either with "Reply from ... " or "Request timed out." If you see "Reply from ...", your computer has found your router.
10) Open your browser and point it to 192.168.1.1. This will take you to your router's login page. Leave the user name blank, and in the password field, enter "admin" (with no quotes). This will take you to your router setup page. Note the version number of your firmware (usually listed near upper right corner of screen). Exit your browser.
If you get this far without problems, try the setup disk (or setup the router manually, if you prefer), and see if you can get your router setup and working.
If you cannot get "Reply from ..." in step 9 above, your router is likely dead. Report back with this problem
If you get a reply in step 9, but cannot complete step 10, then either your router is dead or the firmware is corrupt, or you are having a problem communicating with the router. Report back with this problem.
If you need additional help, please state your ISP, the make and model of your modem, your router's firmware version, and the results of steps 9 and 10. Also, if you get any error messages, copy them exactly and report back.
Please let me know how things turn out for you.
Similar Messages
-
I cannot view my site in browser or publish my site after 2014.3 update
Hi,
I updated to 2014.3 and cannot view my site in browser or publish. I see that alot of other people are having issues. Can you please assist. This is very frustrating.
I am using OS X Yosemite 10.10.2.
Thank you
BrettHi Sanjit,
I cannot even publish the site. Muse crashes when I try to view site in browser and it crashes when I try to publish the site. It is not the browsers - yes I have tried. It has only happened since I updated to 2014.3 - just like everyone else having problems. This is a problem with the update. I can make a new site in the new release and it works - however all existing sites built before 2014.3 release is no good. This a big problem that needs sorting out. I should not have to rebuild everything again. I have sent my muse file via dropbox, as I have seen other people having trouble being asked to send the file through and it will be looked at. The url is http://australiasnaturecoast.businesscatalyst.com/ . This is not the correct version as I made a new site in the new muse update. I need my original version to work. I have tried uninstall and reinstall of Muse and this has not helped.
Thanks -
Due to a scam invading my computer recently, I cannot block these site in Parental Controls. This feature locks immediately and I must use Force Quit to close. Any ideas as to how to unlock Parental Controls? The two scams appear to be gone as I can now use Safari.
howdy my Scotch/Irish brother (I'm Irish descent - actually Norman invader, but hey)
I'm surprised you didn't ask our gracious Hosts to EDIT the live link in the OP's reply - seems very malicious indeed. I reported it already though asking that it be left as merely a domain name - can't save everyone when the ship sinks
buenos dias
ÇÇÇ -
I cannot access a site I use often as a403 error occurs. How do I resolve
I cannot access a site I use often as a 403 error occurs. How do I resolve?
You need to contact the website and tell them to upgrade their security protocols. Especially the following:
* The site uses SSLv3, meaning it's vulnerable to the well known POODLE attack. https://blog.mozilla.org/security/2014/10/14/the-poodle-attack-and-the-end-of-ssl-3-0/
* The site uses RC4, which is insecure.
* The site does not support TLS 1.2, which is recommended.
You can see a full list of all the problems with the website at https://www.ssllabs.com/ssltest/analyze.html?d=secure.crbonline.gov.uk
It very soon will not work in Google Chrome either, so it's in the website's best interest to update ASAP (besides protecting their users from having all their data and information stolen) -
Cannot sigh into sites in Safari
I cannot sign into sites in Safari. I put in user name and password and the sites just cycle back to wanting the username and password.
I got here through Firefox.
I have removed all of the cookies and reset safari, neither of which worked.
What now?Are you running an ad-blocking extension? There are reports here that some can interfere with openign pages that are not threats.
-
Can anyone help me with an iWeb problem? I cannot save the site after making changes. I receive this error: "website.sites2 could not be saved"
You could try duplicating the Domain.sites2 file and launch this in iWeb. Delete the last page you edited and try saving. If that doesn't work, undo and try deleting another and so on...
If you can find the problem page you would only have to rebuild it rather than the whole site.
The other possibility is to create a new site on the same domain file and drag each page in turn down to it from the top site and try to save each time. -
I cannot add a site to the list of allow micro sites on Flash Player settings manager
I cannot add a site to the list of allow micro sites on Flash Player settings manager.
as Adobe says at his help document (http://help.adobe.com/en_US/FlashPlayer/LSM/WS6aa5ec234ff3f285139dc56112e3786b68c-7ff8.htm l):
Displays a list of previously visited websites that have asked to use the camera or microphone on your computer. You can allow or block the use of your camera and microphone by sites on the list. You can also ask to be prompted for permission to use them. Finally, you can choose to remove sites from the list. Removing a site deletes all settings and data stored for that site in Flash Player.
The list initially contains only the sites you have already visited. If you want to specify camera and microphone settings for sites you have not yet visited, you can choose to add sites to the list. Once a site is on the list, you can specify whether to always allow camera and microphone use, ask permission, or never allow camera and microphone use by that site.
I cannot find any button to add a website. Can you help me please.
Thanks in advanced
PedroThere's a "live" panel here: http://www.macromedia.com/support/documentation/en/flashplayer/help/settings_manager06.htm l
-
Cannot acees HTTPS sites in Internet Explorer - Windows 10
In Build 9860 : We cannot access HTTPS sites in Internet Explorer ; unless we put it as a TRUSTED SITE.
A similar issue has existed in Windows 8 and a patch was issued.
I think the same issue has now come back in Windows 10.
Please fix this. Thank you.Well, please try this link in your internet explorer of Windows 10.
https://itldrive.infosys.com/infosys/webview/xythoslogin.action
It doesn't open unless you put it as a trusted site.
However, in Firefox (or IE in Windows 8 or 7) it may open without any issue. -
Purchased new iMac 21.5 in and migrated data from PC using Migration Assistant. I cannot complete setup because my Apple password is being rejected. Also rejects attempts to set new password. Do not want to restart setup process and redo 10 hours of migrating data. any ideas. Thanks
plz check the ip address on your comp---there should not be any static ip---disabled firewall and then try opening 192.168.1.1
by the way, who is the isp? -
<blockquote>Locking duplicate thread.<br>
Please continue here: [[/questions/891666]]</blockquote>
When using Firefox I cannot signin to sites, but can get to sites with tabs on toolbar but cannot signout whe signin, I have uninstalled the program and reinstalled it but still have the same problem.That problem can be caused by the Yahoo! Toolbar that extents too much downwards and covers the top part of the browser window and thus makes links in that part of the screen not clickable.
*https://support.mozilla.com/kb/Troubleshooting+extensions+and+themes
Start Firefox in <u>[[Safe Mode]]</u> to check if one of the extensions or if hardware acceleration is causing the problem (switch to the DEFAULT theme: Firefox (Tools) > Add-ons > Appearance/Themes).
*Don't make any changes on the Safe mode start window.
*https://support.mozilla.com/kb/Safe+Mode
You can keep an eye on this thread:
*[[/forums/contributors/707748]] -
I don't have a history option in bookmarks bar... So I cannot delete visited sites from address bar...how do I restore this ?, I don't have a history option in bookmarks bar... So I cannot delete visited sites from address bar...how do I restore this ?
The history option is the little clock icon at the bottom of the Bookmarks menu - the icon in the center between the open book and the eye glasses icons. You don't have that? Try closing Safari and see if the history option comes back
Go to the home screen first by tapping the home button. Double tap the home button and the task bar will appear with all of your recent/open apps displayed at the bottom. Tap and hold down on any app icon until it begins to wiggle. Tap the minus sign in the upper left corner of the app that you want to close. Tap the home button or anywhere above the task bar. Restart the iPad.
Restart the iPad by holding down on the sleep button until the red slider appears and then slide to shut off. To power up hold the sleep button until the Apple logo appears and let go of the button.
You can also clear the history in Settings>Safari>Clear History. -
Cannot mark the 'site' location of instances fixed, Bel does not match
Hello,
i have a problem using the PlanAhead Tool (v.14.5) from the ISE (v.14.5).
First of all, i have loaded an .ucf-file to define various IO for the Design. After that, i have createt a pblock for some part of the design, which also includes some of the previous mentioned IOs. I said to PlanAhead, that it should use the IO as predefined. The design compiles without error and works quite fine.
The next step for me now is to lock the pblock, which means to fix the instance, so that the compiler does not have to re-map and -place&route this part of the design. (so i try to fix the part of the netlist)
And if i try to do this, i get different errors:
- marking the whole pblock and right click --> fix instances i get the following error:
Cannot mark the 'site' location of instances fixed, Bel does not match
with the valid locations at which this inst can be placed
So i searched for this special problem and found this:
Vivado Solution which seems to be a bug in the PlanAhead software from Vivado. My question is : is in my PlanAhead ISE version the same bug ?
(copying and typing the same command in the tcl console does not work)
- Second: i tried to manuel set primitives to "fix instances" which works quite fine for most of the primitives but not for all. Some of these produce errors like:
Cannot mark the 'bel' location of instances fixed, 'Element
SLICE_X66Y112.B5LUT can not be used as a route-through for net xy
because a RAM or shift register is placed there'
Is it still a bug, can i somehow resolve this error ?
I hope you can help me out here.
Best regards.Hello,
thanks for your answer.
I send you the two ucf files:
The first one is the "original" ucf used to define the constrains (I/O,...) and the second the one PlanAhead has generated (but with no "fixed instances") .
Thanks -
I am using adobe Muse and publishing to BC.
I had set up the site wrongly on BC so had deleted it and the records.
When I go to create it again it says that:
"Domain already exists. Please delete all records associated with this domain before re-adding it."
Any help would be gratefully appreciated.Hi,
Please reach out to the support team or submit a ticket, and they will assist you further. Or let me know the domain and I will check it. -
Cannot create root site in newly configured SP2013 farm
I just finished running the configuration wizard and built the sp2013 farm. I then created the web application and now I am trying to create the root site in the web application.
But on browser it says "Something went wrong. user cannot be found"
In ULS Log there is an exception
Application error when access /_admin/createsite.aspx, Error=User cannot be found. at Microsoft.SharePoint.Administration.SPSiteCollection.Add(SPContentDatabase database, SPSiteSubscription siteSubscription, String siteUrl, String title, String
description, UInt32 nLCID, Int32 compatibilityLevel, String webTemplate, String ownerLogin, String ownerName, String ownerEmail, String secondaryContactLogin, String secondaryContactName, String secondaryContactEmail, String quotaTemplate, String sscRootWebUrl,
Boolean useHostHeaderAsSiteName, Boolean overrideCompatibilityRestriction) at Microsoft.SharePoint.Administration.SPSiteCollection.Add(SPSiteSubscription siteSubscription, String siteUrl, String title, String description, UInt32 nLCID,
Int32 compatibilityLevel, String webTemplate, Strin... 5a89e89b-cf23-0000-7132-bd7bab5593a4
...g ownerLogin, String ownerName, String ownerEmail, String secondaryContactLogin, String secondaryContactName, String secondaryContactEmail, Boolean useHostHeaderAsSiteName) at Microsoft.SharePoint.ApplicationPages.CreateSitePage.BtnCreateSite_Click(Object
sender, EventArgs e) at System.Web.UI.WebControls.Button.RaisePostBackEvent(String eventArgument) at System.Web.UI.Page.ProcessRequestMain(Boolean includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint) 5a89e89b-cf23-0000-7132-bd7bab5593a4
Microsoft.SharePoint.SPException: User cannot be found. at Microsoft.SharePoint.Administration.SPSiteCollection.Add(SPContentDatabase database, SPSiteSubscription siteSubscription, String siteUrl, String title, String description, UInt32 nLCID,
Int32 compatibilityLevel, String webTemplate, String ownerLogin, String ownerName, String ownerEmail, String secondaryContactLogin, String secondaryContactName, String secondaryContactEmail, String quotaTemplate, String sscRootWebUrl, Boolean useHostHeaderAsSiteName,
Boolean overrideCompatibilityRestriction) at Microsoft.SharePoint.Administration.SPSiteCollection.Add(SPSiteSubscription siteSubscription, String siteUrl, String title, String description, UInt32 nLCID, Int32 compatibilityLevel, String
webTemplate, String ownerLogin, String owner... 5a89e89b-cf23-0000-7132-bd7bab5593a4
val it: unit=()Please check following:
1) Any UPN change in your organization
2) Any authentication changes on Web Application: if you switched between NTLM to Kerb.
3) Check if User Profile Service is able to connect to AD/DC.
4) PeoplePicker: What is your peoplepicker doing.
5) Check SuperUser/Reader accounts are properly set.
6) See if blobcache is setup correctly
In my case, I had issue with PeoplePicker. How would you know? Open Manage Web Applications, select a web application and select User Policy. Try to add a domain user there and see if it resolves user name. If not then this means users who are trying to
create their mysites are having one of above mentioned issues. -
VPN Clients cannot access remote site
Hey there,
I am pretty new in configuring Cisco devices and now I need some help.
I have 2 site here:
site A
Cisco 891
external IP: 195.xxx.yyy.zzz
VPN Gateway for Remote users
local IP: VLAN10 10.133.10.0 /23
site B
Cisco 891
external IP: 62.xxx.yyy.zzz
local IP VLAN10 10.133.34.0 /23
Those two sites are linked together with a Site-to-Site VPN. Accessing files or ressources from one site to the other is working fine while connected to the local LAN.
I configured VPN connection with Radius auth. VPN clients can connect to Site A, get an IP adress from VPN Pool (172.16.100.2-100) and can access files and servers on site A. But for some reason they cannot access ressources on site B. I already added the site B network to the ACL and when connecting with VPN it shows secured routes to 10.133.10.0 and 10.133.34.0 in the statistics. Same thing for other VPN Tunnels to ERP system.
What is missing here to make it possible to reach remote sites when connected through VPN? I had a look at the logs but could not find anything important.
Here is the config of site A
Building configuration...
Current configuration : 24257 bytes
version 15.2
no service pad
service tcp-keepalives-in
service tcp-keepalives-out
service timestamps debug datetime msec localtime show-timezone
service timestamps log datetime msec localtime show-timezone
service password-encryption
service sequence-numbers
hostname Englerstrasse
boot-start-marker
boot config usbflash0:CVO-BOOT.CFG
boot-end-marker
aaa new-model
aaa group server radius Radius-AD
server 10.133.10.5 auth-port 1812 acct-port 1813
aaa authentication login default local
aaa authentication login ciscocp_vpn_xauth_ml_2 group Radius-AD local
aaa authorization exec default local
aaa authorization network ciscocp_vpn_group_ml_2 local
aaa session-id common
clock timezone Berlin 1 0
clock summer-time Berlin date Mar 30 2003 2:00 Oct 26 2003 3:00
crypto pki trustpoint TP-self-signed-27361994
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-27361994
revocation-check none
rsakeypair TP-self-signed-27361994
crypto pki trustpoint test_trustpoint_config_created_for_sdm
subject-name [email protected]
revocation-check crl
crypto pki certificate chain TP-self-signed-27361994
certificate self-signed 01
30820227 30820190 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
2F312D30 2B060355 04031324 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 32373336 31393934 301E170D 31323038 32373038 30343238
5A170D32 30303130 31303030 3030305A 302F312D 302B0603 55040313 24494F53
2D53656C 662D5369 676E6564 2D436572 74696669 63617465 2D323733 36313939
3430819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281 8100B709
64CE1874 BF812A9F 0B761522 892373B9 10F0BB52 6263DCDB F9877AA3 7BD34E53
BCFDA45C 2A991777 4DDC7E6B 1FCEE36C B6E35679 C4A18771 9C0F871F 38310234
2D89A4FF 37B616D8 362B3103 A8A319F2 10A72DC7 490A04AC 7955DF68 32EF9615
9E1A3B31 2A1AB243 B3ED3E35 F4AAD029 CDB1F941 5E794300 5C5EF8AE 5C890203
010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603 551D2304
18301680 14D0F5E7 D3A9311D 1675AA8F 38F064FC 4D04465E F5301D06 03551D0E
04160414 D0F5E7D3 A9311D16 75AA8F38 F064FC4D 04465EF5 300D0609 2A864886
F70D0101 05050003 818100AB 2CD4363A E5ADBFB0 943A38CB AC820801 117B52CC
20216093 79D1F777 2B3C0062 4301CF73 094B9CA5 805F585E 04CF3301 9B839DEB
14A334A2 F5A5316F C65EEF21 0B0DF3B5 F4322440 F28B984B E769876D 6EF94895
C3D5048A A4E2A180 12DF6652 176942F8 58187D7B D37B1F1A 4DDD7AE9 5189F9AF
AF3EF676 26AD3F31 D368F5
quit
crypto pki certificate chain test_trustpoint_config_created_for_sdm
no ip source-route
ip auth-proxy max-login-attempts 5
ip admission max-login-attempts 5
no ip bootp server
no ip domain lookup
ip domain name yourdomain.com
ip inspect log drop-pkt
ip inspect name CCP_MEDIUM appfw CCP_MEDIUM
ip inspect name CCP_MEDIUM ftp
ip inspect name CCP_MEDIUM h323
ip inspect name CCP_MEDIUM sip
ip inspect name CCP_MEDIUM https
ip inspect name CCP_MEDIUM icmp
ip inspect name CCP_MEDIUM netshow
ip inspect name CCP_MEDIUM rcmd
ip inspect name CCP_MEDIUM realaudio
ip inspect name CCP_MEDIUM rtsp
ip inspect name CCP_MEDIUM sqlnet
ip inspect name CCP_MEDIUM streamworks
ip inspect name CCP_MEDIUM tftp
ip inspect name CCP_MEDIUM udp
ip inspect name CCP_MEDIUM vdolive
ip inspect name CCP_MEDIUM imap reset
ip inspect name CCP_MEDIUM smtp
ip cef
no ipv6 cef
appfw policy-name CCP_MEDIUM
application im aol
service default action allow alarm
service text-chat action allow alarm
server permit name login.oscar.aol.com
server permit name toc.oscar.aol.com
server permit name oam-d09a.blue.aol.com
audit-trail on
application im msn
service default action allow alarm
service text-chat action allow alarm
server permit name messenger.hotmail.com
server permit name gateway.messenger.hotmail.com
server permit name webmessenger.msn.com
audit-trail on
application http
strict-http action allow alarm
port-misuse im action reset alarm
port-misuse p2p action reset alarm
port-misuse tunneling action allow alarm
application im yahoo
service default action allow alarm
service text-chat action allow alarm
server permit name scs.msg.yahoo.com
server permit name scsa.msg.yahoo.com
server permit name scsb.msg.yahoo.com
server permit name scsc.msg.yahoo.com
server permit name scsd.msg.yahoo.com
server permit name cs16.msg.dcn.yahoo.com
server permit name cs19.msg.dcn.yahoo.com
server permit name cs42.msg.dcn.yahoo.com
server permit name cs53.msg.dcn.yahoo.com
server permit name cs54.msg.dcn.yahoo.com
server permit name ads1.vip.scd.yahoo.com
server permit name radio1.launch.vip.dal.yahoo.com
server permit name in1.msg.vip.re2.yahoo.com
server permit name data1.my.vip.sc5.yahoo.com
server permit name address1.pim.vip.mud.yahoo.com
server permit name edit.messenger.yahoo.com
server permit name messenger.yahoo.com
server permit name http.pager.yahoo.com
server permit name privacy.yahoo.com
server permit name csa.yahoo.com
server permit name csb.yahoo.com
server permit name csc.yahoo.com
audit-trail on
parameter-map type inspect global
log dropped-packets enable
multilink bundle-name authenticated
redundancy
ip tcp synwait-time 10
class-map match-any CCP-Transactional-1
match dscp af21
match dscp af22
match dscp af23
class-map match-any CCP-Voice-1
match dscp ef
class-map match-any sdm_p2p_kazaa
match protocol fasttrack
match protocol kazaa2
class-map match-any CCP-Routing-1
match dscp cs6
class-map match-any sdm_p2p_edonkey
match protocol edonkey
class-map match-any CCP-Signaling-1
match dscp cs3
match dscp af31
class-map match-any sdm_p2p_gnutella
match protocol gnutella
class-map match-any CCP-Management-1
match dscp cs2
class-map match-any sdm_p2p_bittorrent
match protocol bittorrent
policy-map sdm-qos-test-123
class class-default
policy-map sdmappfwp2p_CCP_MEDIUM
class sdm_p2p_edonkey
class sdm_p2p_gnutella
class sdm_p2p_kazaa
class sdm_p2p_bittorrent
policy-map CCP-QoS-Policy-1
class sdm_p2p_edonkey
class sdm_p2p_gnutella
class sdm_p2p_kazaa
class sdm_p2p_bittorrent
class CCP-Voice-1
priority percent 33
class CCP-Signaling-1
bandwidth percent 5
class CCP-Routing-1
bandwidth percent 5
class CCP-Management-1
bandwidth percent 5
class CCP-Transactional-1
bandwidth percent 5
class class-default
fair-queue
random-detect
crypto ctcp port 10000
crypto isakmp policy 1
encr 3des
authentication pre-share
group 2
crypto isakmp key REMOVED address 62.20.xxx.yyy
crypto isakmp key REMOVED address 195.243.xxx.yyy
crypto isakmp key REMOVED address 195.243.xxx.yyy
crypto isakmp key REMOVED address 83.140.xxx.yyy
crypto isakmp client configuration group VPN_local
key REMOVED
dns 10.133.10.5 10.133.10.7
wins 10.133.10.7
domain domain.de
pool SDM_POOL_2
acl 115
crypto isakmp profile ciscocp-ike-profile-1
match identity group VPN_local
client authentication list ciscocp_vpn_xauth_ml_2
isakmp authorization list ciscocp_vpn_group_ml_2
client configuration address respond
virtual-template 1
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA1 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA2 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA3 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA4 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA11 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-3DES-SHA5 esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-DES-SHA1 esp-des esp-sha-hmac
crypto ipsec profile CiscoCP_Profile1
set transform-set ESP-3DES-SHA11
set isakmp-profile ciscocp-ike-profile-1
crypto map SDM_CMAP_1 1 ipsec-isakmp
description Tunnel to62.20.xxx.xxx
set peer 62.20.xxx.xxx
set transform-set ESP-3DES-SHA
match address 105
crypto map SDM_CMAP_1 2 ipsec-isakmp
description Tunnel to195.243.xxx.xxx
set peer 195.243.xxx.xxx
set transform-set ESP-3DES-SHA4
match address 107
crypto map SDM_CMAP_1 3 ipsec-isakmp
description Tunnel to83.140.xxx.xxx
set peer 83.140.xxx.xxx
set transform-set ESP-DES-SHA1
match address 118
interface Loopback2
ip address 192.168.10.1 255.255.254.0
interface Null0
no ip unreachables
interface FastEthernet0
switchport mode trunk
no ip address
spanning-tree portfast
interface FastEthernet1
no ip address
spanning-tree portfast
interface FastEthernet2
no ip address
spanning-tree portfast
interface FastEthernet3
no ip address
spanning-tree portfast
interface FastEthernet4
description Internal LAN
switchport access vlan 10
switchport trunk native vlan 10
no ip address
spanning-tree portfast
interface FastEthernet5
no ip address
spanning-tree portfast
interface FastEthernet6
no ip address
spanning-tree portfast
interface FastEthernet7
no ip address
spanning-tree portfast
interface FastEthernet8
description $FW_OUTSIDE$$ETH-WAN$
ip address 62.153.xxx.xxx 255.255.255.248
ip access-group 113 in
no ip redirects
no ip unreachables
no ip proxy-arp
ip nat outside
ip inspect CCP_MEDIUM out
no ip virtual-reassembly in
ip verify unicast reverse-path
duplex auto
speed auto
crypto map SDM_CMAP_1
service-policy input sdmappfwp2p_CCP_MEDIUM
service-policy output CCP-QoS-Policy-1
interface Virtual-Template1 type tunnel
ip unnumbered FastEthernet8
tunnel mode ipsec ipv4
tunnel protection ipsec profile CiscoCP_Profile1
interface GigabitEthernet0
no ip address
shutdown
duplex auto
speed auto
interface Vlan1
no ip address
interface Vlan10
description $FW_INSIDE$
ip address 10.133.10.1 255.255.254.0
ip access-group 112 in
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly in
interface Async1
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
encapsulation slip
ip local pool SDM_POOL_1 192.168.10.101 192.168.10.200
ip local pool VPN_Pool 192.168.20.2 192.168.20.100
ip local pool SDM_POOL_2 172.16.100.2 172.16.100.100
ip http server
ip http access-class 23
ip http authentication local
ip http secure-server
ip http timeout-policy idle 60 life 86400 requests 10000
ip forward-protocol nd
ip nat inside source route-map SDM_RMAP_1 interface FastEthernet8 overload
ip route 0.0.0.0 0.0.0.0 62.153.xxx.xxx
ip access-list extended VPN1
remark VPN_Haberstrasse
remark CCP_ACL Category=4
permit ip 10.133.10.0 0.0.1.255 10.133.34.0 0.0.1.255
ip radius source-interface Vlan10
access-list 1 remark INSIDE_IF=Vlan1
access-list 1 remark CCP_ACL Category=2
access-list 1 permit 10.10.10.0 0.0.0.7
access-list 23 remark CCP_ACL Category=17
access-list 23 permit 195.243.xxx.xxx
access-list 23 permit 10.133.10.0 0.0.1.255
access-list 23 permit 10.10.10.0 0.0.0.7
access-list 100 remark CCP_ACL Category=4
access-list 100 permit ip 10.133.10.0 0.0.1.255 any
access-list 101 remark CCP_ACL Category=16
access-list 101 permit udp any eq bootps any eq bootpc
access-list 101 deny ip 10.10.10.0 0.0.0.255 any
access-list 101 permit icmp any any echo-reply
access-list 101 permit icmp any any time-exceeded
access-list 101 permit icmp any any unreachable
access-list 101 deny ip 10.0.0.0 0.255.255.255 any
access-list 101 deny ip 172.16.0.0 0.15.255.255 any
access-list 101 deny ip 192.168.0.0 0.0.255.255 any
access-list 101 deny ip 127.0.0.0 0.255.255.255 any
access-list 101 deny ip host 255.255.255.255 any
access-list 101 deny ip any any
access-list 102 remark auto generated by CCP firewall configuration
access-list 102 remark CCP_ACL Category=1
access-list 102 deny ip 10.10.10.0 0.0.0.7 any
access-list 102 permit icmp any host 62.153.xxx.xxx echo-reply
access-list 102 permit icmp any host 62.153.xxx.xxx time-exceeded
access-list 102 permit icmp any host 62.153.xxx.xxx unreachable
access-list 102 deny ip 10.0.0.0 0.255.255.255 any
access-list 102 deny ip 172.16.0.0 0.15.255.255 any
access-list 102 deny ip 192.168.0.0 0.0.255.255 any
access-list 102 deny ip 127.0.0.0 0.255.255.255 any
access-list 102 deny ip host 255.255.255.255 any
access-list 102 deny ip host 0.0.0.0 any
access-list 102 deny ip any any log
access-list 103 remark auto generated by CCP firewall configuration
access-list 103 remark CCP_ACL Category=1
access-list 103 remark IPSec Rule
access-list 103 permit ip 10.133.34.0 0.0.1.255 10.133.10.0 0.0.1.255
access-list 103 remark IPSec Rule
access-list 103 permit ip 10.133.34.0 0.0.1.255 192.168.10.0 0.0.1.255
access-list 103 permit udp host 195.243.xxx.xxx host 62.153.xxx.xxx eq non500-isakmp
access-list 103 permit udp host 195.243.xxx.xxx host 62.153.xxx.xxx eq isakmp
access-list 103 permit esp host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 103 permit ahp host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 103 remark IPSec Rule
access-list 103 permit ip 10.133.20.0 0.0.0.255 10.133.10.0 0.0.1.255
access-list 103 remark IPSec Rule
access-list 103 permit ip 192.168.10.0 0.0.1.255 10.133.10.0 0.0.1.255
access-list 103 permit udp host 62.20.xxx.xxx host 62.153.xxx.xxx eq non500-isakmp
access-list 103 permit udp host 62.20.xxx.xxx host 62.153.xxx.xxx eq isakmp
access-list 103 permit esp host 62.20.xxx.xxx host 62.153.xxx.xxx
access-list 103 permit ahp host 62.20.xxx.xxx host 62.153.xxx.xxx
access-list 103 permit udp any host 62.153.xxx.xxx eq non500-isakmp
access-list 103 permit udp any host 62.153.xxx.xxx eq isakmp
access-list 103 permit esp any host 62.153.xxx.xxx
access-list 103 permit ahp any host 62.153.xxx.xxx
access-list 103 permit udp host 194.25.0.60 eq domain any
access-list 103 permit udp host 194.25.0.68 eq domain any
access-list 103 permit udp host 194.25.0.68 eq domain host 62.153.xxx.xxx
access-list 103 deny ip 10.10.10.0 0.0.0.7 any
access-list 103 permit icmp any host 62.153.xxx.xxx echo-reply
access-list 103 permit icmp any host 62.153.xxx.xxx time-exceeded
access-list 103 permit icmp any host 62.153.xxx.xxx unreachable
access-list 103 deny ip 10.0.0.0 0.255.255.255 any
access-list 103 deny ip 172.16.0.0 0.15.255.255 any
access-list 103 deny ip 192.168.0.0 0.0.255.255 any
access-list 103 deny ip 127.0.0.0 0.255.255.255 any
access-list 103 deny ip host 255.255.255.255 any
access-list 103 deny ip host 0.0.0.0 any
access-list 103 deny ip any any log
access-list 104 remark CCP_ACL Category=4
access-list 104 permit ip 10.133.10.0 0.0.1.255 any
access-list 105 remark CCP_ACL Category=4
access-list 105 remark IPSec Rule
access-list 105 permit ip 10.133.10.0 0.0.1.255 10.133.20.0 0.0.0.255
access-list 106 remark CCP_ACL Category=2
access-list 106 remark IPSec Rule
access-list 106 deny ip 192.168.10.0 0.0.1.255 10.133.34.0 0.0.1.255
access-list 106 remark IPSec Rule
access-list 106 deny ip 192.168.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 106 remark IPSec Rule
access-list 106 deny ip 10.133.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 106 remark IPSec Rule
access-list 106 deny ip 10.133.10.0 0.0.1.255 10.133.34.0 0.0.1.255
access-list 106 remark IPSec Rule
access-list 106 deny ip 10.133.10.0 0.0.1.255 10.133.20.0 0.0.0.255
access-list 106 permit ip 10.10.10.0 0.0.0.7 any
access-list 106 permit ip 10.133.10.0 0.0.1.255 any
access-list 107 remark CCP_ACL Category=4
access-list 107 remark IPSec Rule
access-list 107 permit ip 10.133.10.0 0.0.1.255 10.133.34.0 0.0.1.255
access-list 107 remark IPSec Rule
access-list 107 permit ip 192.168.10.0 0.0.1.255 10.133.34.0 0.0.1.255
access-list 108 remark Auto generated by SDM Management Access feature
access-list 108 remark CCP_ACL Category=1
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq telnet
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq 22
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq www
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq 443
access-list 108 permit tcp 10.133.10.0 0.0.1.255 host 10.133.10.1 eq cmd
access-list 108 deny tcp any host 10.133.10.1 eq telnet
access-list 108 deny tcp any host 10.133.10.1 eq 22
access-list 108 deny tcp any host 10.133.10.1 eq www
access-list 108 deny tcp any host 10.133.10.1 eq 443
access-list 108 deny tcp any host 10.133.10.1 eq cmd
access-list 108 deny udp any host 10.133.10.1 eq snmp
access-list 108 permit ip any any
access-list 109 remark CCP_ACL Category=1
access-list 109 permit ip 10.133.10.0 0.0.1.255 any
access-list 109 permit ip 10.10.10.0 0.0.0.7 any
access-list 109 permit ip 192.168.10.0 0.0.1.255 any
access-list 110 remark CCP_ACL Category=1
access-list 110 permit ip host 195.243.xxx.xxx any
access-list 110 permit ip host 84.44.xxx.xxx any
access-list 110 permit ip 10.133.10.0 0.0.1.255 any
access-list 110 permit ip 10.10.10.0 0.0.0.7 any
access-list 110 permit ip 192.168.10.0 0.0.1.255 any
access-list 111 remark CCP_ACL Category=4
access-list 111 permit ip 10.133.10.0 0.0.1.255 any
access-list 112 remark CCP_ACL Category=1
access-list 112 permit udp host 10.133.10.5 eq 1812 any
access-list 112 permit udp host 10.133.10.5 eq 1813 any
access-list 112 permit udp any host 10.133.10.1 eq non500-isakmp
access-list 112 permit udp any host 10.133.10.1 eq isakmp
access-list 112 permit esp any host 10.133.10.1
access-list 112 permit ahp any host 10.133.10.1
access-list 112 permit udp host 10.133.10.5 eq 1645 host 10.133.10.1
access-list 112 permit udp host 10.133.10.5 eq 1646 host 10.133.10.1
access-list 112 remark auto generated by CCP firewall configuration
access-list 112 permit udp host 10.133.10.5 eq 1812 host 10.133.10.1
access-list 112 permit udp host 10.133.10.5 eq 1813 host 10.133.10.1
access-list 112 permit udp host 10.133.10.7 eq domain any
access-list 112 permit udp host 10.133.10.5 eq domain any
access-list 112 deny ip 62.153.xxx.xxx 0.0.0.7 any
access-list 112 deny ip 10.10.10.0 0.0.0.7 any
access-list 112 deny ip host 255.255.255.255 any
access-list 112 deny ip 127.0.0.0 0.255.255.255 any
access-list 112 permit ip any any
access-list 113 remark CCP_ACL Category=1
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.133.34.0 0.0.1.255 192.168.10.0 0.0.1.255
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.60.16.0 0.0.0.255 192.168.10.0 0.0.1.255
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.60.16.0 0.0.0.255 10.133.10.0 0.0.1.255
access-list 113 permit udp host 83.140.100.4 host 62.153.xxx.xxx eq non500-isakmp
access-list 113 permit udp host 83.140.100.4 host 62.153.xxx.xxx eq isakmp
access-list 113 permit esp host 83.140.100.4 host 62.153.xxx.xxx
access-list 113 permit ahp host 83.140.100.4 host 62.153.xxx.xxx
access-list 113 permit ip host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 113 permit ip host 84.44.xxx.xxx host 62.153.xxx.xxx
access-list 113 remark auto generated by CCP firewall configuration
access-list 113 permit udp host 194.25.0.60 eq domain any
access-list 113 permit udp host 194.25.0.68 eq domain any
access-list 113 permit udp host 194.25.0.68 eq domain host 62.153.xxx.xxx
access-list 113 permit udp host 194.25.0.60 eq domain host 62.153.xxx.xxx
access-list 113 permit udp any host 62.153.xxx.xxx eq non500-isakmp
access-list 113 permit udp any host 62.153.xxx.xxx eq isakmp
access-list 113 permit esp any host 62.153.xxx.xxx
access-list 113 permit ahp any host 62.153.xxx.xxx
access-list 113 permit ahp host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 113 permit esp host 195.243.xxx.xxx host 62.153.xxx.xxx
access-list 113 permit udp host 195.243.xxx.xxx host 62.153.xxx.xxx eq isakmp
access-list 113 permit udp host 195.243.xxx.xxx host 62.153.xxx.xxx eq non500-isakmp
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.133.34.0 0.0.1.255 10.133.10.0 0.0.1.255
access-list 113 permit ahp host 62.20.xxx.xxx host 62.153.xxx.xxx
access-list 113 remark IPSec Rule
access-list 113 permit ip 192.168.10.0 0.0.1.255 10.133.10.0 0.0.1.255
access-list 113 permit esp host 62.20.xxx.xxx host 62.153.xxx.xxx
access-list 113 permit udp host 62.20.xxx.xxx host 62.153.xxx.xxx eq isakmp
access-list 113 permit udp host 62.20.xxx.xxx host 62.153.xxx.xxx eq non500-isakmp
access-list 113 remark IPSec Rule
access-list 113 permit ip 10.133.20.0 0.0.0.255 10.133.10.0 0.0.1.255
access-list 113 remark Pop3
access-list 113 permit tcp host 82.127.xxx.xxx eq 8080 host 62.153.xxx.xxx
access-list 113 remark Pop3
access-list 113 permit tcp any eq pop3 host 62.153.xxx.xxx
access-list 113 remark SMTP
access-list 113 permit tcp any eq 465 host 62.153.xxx.xxx
access-list 113 remark IMAP
access-list 113 permit tcp any eq 587 host 62.153.xxx.xxx
access-list 113 deny ip 10.133.10.0 0.0.1.255 any
access-list 113 deny ip 10.10.10.0 0.0.0.7 any
access-list 113 permit icmp any host 62.153.xxx.xxx echo-reply
access-list 113 permit icmp any host 62.153.xxx.xxx time-exceeded
access-list 113 permit icmp any host 62.153.xxx.xxx unreachable
access-list 113 deny ip 10.0.0.0 0.255.255.255 any
access-list 113 deny ip 172.16.0.0 0.15.255.255 any
access-list 113 deny ip 192.168.0.0 0.0.255.255 any
access-list 113 deny ip 127.0.0.0 0.255.255.255 any
access-list 113 deny ip host 255.255.255.255 any
access-list 113 deny ip host 0.0.0.0 any
access-list 113 deny ip any any log
access-list 114 remark auto generated by CCP firewall configuration
access-list 114 remark CCP_ACL Category=1
access-list 114 deny ip 10.133.10.0 0.0.1.255 any
access-list 114 deny ip 10.10.10.0 0.0.0.7 any
access-list 114 permit icmp any any echo-reply
access-list 114 permit icmp any any time-exceeded
access-list 114 permit icmp any any unreachable
access-list 114 deny ip 10.0.0.0 0.255.255.255 any
access-list 114 deny ip 172.16.0.0 0.15.255.255 any
access-list 114 deny ip 192.168.0.0 0.0.255.255 any
access-list 114 deny ip 127.0.0.0 0.255.255.255 any
access-list 114 deny ip host 255.255.255.255 any
access-list 114 deny ip host 0.0.0.0 any
access-list 114 deny ip any any log
access-list 115 remark VPN_Sub
access-list 115 remark CCP_ACL Category=5
access-list 115 permit ip 10.133.10.0 0.0.1.255 172.16.0.0 0.0.255.255
access-list 115 permit ip 10.133.34.0 0.0.1.255 172.16.0.0 0.0.255.255
access-list 115 permit ip 10.133.20.0 0.0.0.255 any
access-list 116 remark CCP_ACL Category=4
access-list 116 remark IPSec Rule
access-list 116 permit ip 10.133.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 117 remark CCP_ACL Category=4
access-list 117 remark IPSec Rule
access-list 117 permit ip 10.133.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 118 remark CCP_ACL Category=4
access-list 118 remark IPSec Rule
access-list 118 permit ip 10.133.10.0 0.0.1.255 10.60.16.0 0.0.0.255
access-list 118 remark IPSec Rule
access-list 118 permit ip 192.168.10.0 0.0.1.255 10.60.16.0 0.0.0.255
no cdp run
route-map SDM_RMAP_1 permit 1
match ip address 106
control-plane
mgcp profile default
line con 0
transport output telnet
line 1
modem InOut
speed 115200
flowcontrol hardware
line aux 0
transport output telnet
line vty 0 4
session-timeout 45
access-class 110 in
transport input telnet ssh
line vty 5 15
access-class 109 in
transport input telnet ssh
scheduler interval 500
endThe crypto ACL for the site to site vpn should also include the vpn client pool, otherwise, traffic from the vpn client does not match the interesting traffic for the site to site vpn.
On Site A:
should include "access-list 107 permit ip 172.16.100.0 0.0.0.255 10.133.34.0 0.0.1.255"
You should also remove the following line as the pool is incorrect:
access-list 107 permit ip 192.168.10.0 0.0.1.255 10.133.34.0 0.0.1.255
On Site B:
should include: permit ip 10.133.34.0 0.0.1.255 172.16.100.0 0.0.0.255"
NAT exemption on site B should also be configured with deny on the above ACL.
Maybe you are looking for
-
Hi, I'm trying to uninstall my OVI Suite, but the software always reinstall, over and over again. I do it through the pointer remove programs in WinXP. Where I find the menu uninstall in the ovi suite, if this menu is not showed? Has someone a good i
-
Accidentally deleted plugins, now iTunes wont't open.
Anybody know how to get deleted plugins back so I can access iTunes?
-
Using 2..02 on my zen micro and windows does not see my player through the usb port. Is it true that I need to upgrade XP to service Pack 2? I'd like to avoid this if possible. Does anybody else use this firmware with SP ?Thanks!
-
Is anyone able to explain really poor performance when using 'If Exists'?
Hello all. We've recently had a performance spike when using the 'if exists' construct, which is a construct that we use through much of our code. The problem is, it appears illogical since if can be removed via a tiny modification that does not ch
-
hola por favor ayudenme quisiera saber como localizar un ipod touch de 4 generacion que me fue robado