Cannot Complete Setup Wizard

Hello. Currently have a cable provider with a wired network using a wired router. Replacing the wired router (different manufacturer) with the Linksys WRT54G v6 router.
Followed the instructions from the Setup Wizard disc. Install keeps getting hung up in screen where the computer settings is being tested. It cannot connecto to the internet.
I have taken the router out of the equation by connecting directly from the modem to the computer and I am able to get an internet connection.
I have reset the router, changed wires, double-checked to make sure all wires are seated properly, rebooted the computer, modem and router, all to no avail.
Any suggestions are welcome.
Thanks.

plz check the ip address on your comp---there should not be any static ip---disabled firewall and then try opening 192.168.1.1
by the way, who is the isp?

Similar Messages

Cannot complete setup

Purchased new iMac 21.5 in and migrated data from PC using Migration Assistant. I cannot complete setup because my Apple password is being rejected. Also rejects attempts to set new password. Do not want to restart setup process and redo 10 hours of migrating data. any ideas. Thanks

plz check the ip address on your comp---there should not be any static ip---disabled firewall and then try opening 192.168.1.1
by the way, who is the isp?

Cannot complete setup on my Qosimo F60

Hi
I have a Qosmio F60. Its new and I gave it to an IT person who initially set it up. I intended to use it with my race car simulator. Now after it is being not used at all I have pulled it out of the box and the username and password would not open the computer.
So stupid me restarted the laptop using the "restoring the pre-installed software recovery from the recovery hard disc drive" as described in the users manual. It went through the process till it got to ticking the user agreement box which I could not move the cursor to tick the authority.
Im now stuck at that level of programming. Can anyone help me complete the set up?
Thank you.
Gerry

If you cannot move mouse pointer use tab button and go to cancel option. When option cancel is framed press ENTER and I hope you will be able to continue setup option.
Test it please and post some feedback.
To be honest it is strange to me that you cannot use mouse pointer.

Not connecting to internet after installing os x mavericks. and thus i cannot complete setup

please help
today i installed mavrericks update and now my mac is showing new setup window. but it is not connecting to internet and i cannot sign in to apple account. and it seems like i lost all my data.. please help me. if i lost my data i will be killed.i feel like the new os is not installled properly. is there any way to reinstall it. do i have to download the os x again. please help me. i am in deep problem

Have you looked here:
Re: osx Mavericks can't save scanned documents with hp scanjet

Setup Assistant Freezes after installation.. cannot complete setup

Hi - I recently installed an Apple DVD RAM drive in my 450Mhz B&W G3. As far as I know it meets the system requirements - it has 640MB RAM and built in firewire.
Anyway, I was upgrading from OS 10.2.8 and I kept getting an error. So I ran the disk utility and sure enough, there was an error - and one that it couldn't fix. So I backed up all my files and decided to clean install, and it worked perfectly.
Installation had no problems, and it got completely through to the setup assistant. Except, now it got to the "select keyboard language: English, Canadian or "view all languages" - when I select English and click "continue" it freezes. Sometimes I get the spinning colorful wheel, and othertimes, it just stays frozen. After about 10 minutes, it comes back to where I can click "continue again" When I do, the continue button goes grey and it just sits there idling again.
Anyone know what the problem is or how to fix it? Thanks!
Tim

never mind, it simply needed more time - I left it for a few hours and came back and it finally made it to the next screen! Weird.
Tim

Windows 7 - "Cannot complete setup" of Windows XP Mode

I am running Win 7 OEM 64 bit PRO on new PC:
AMD FX-8120, Gigabyte GA-990FXA-UD3 MOBO, latest BIOS
The setup gets to 99% then fails with the above message. So far I have tried:
Ensuring Virtualisation is on in BIOS
There are no bootable disks in the drive
I am running as admin with my own account logon name
I have run SFC - no conflicts
Yes I have downloaded the correct XP mode file
I have re-installed Win 7 and tried to run before installing any drivers or apps - same problem.
Now what? I tried vmware but the standalone converter gave me an error message saying it was not configured properly. I suspect either a policy problem with Win 7 or a MOBO bios incompatibility. Anyone got any ideas?

@robonline
I believe I'm seeing this same issue as well, I've got a windows 7 system that was running with an Athlon II 250 on which Windows XP mode installed and worked perfectly.
However when I upgraded the CPU to an AMD FX-8150 (in an otherwise unchanged system) Windows XP mode no longer starts properly, it seems to hang before the Virtual PC starts to boot the OS (so possibly either during BIOS POST, or right
at the transition.
I've discovered that it doesn't ALWAYS fail, and if power of the Virtual PC and Start it again a few times in quick succession it seems to then get past what ever point causes the problem and then boots the XP Virtual PC and
it works normally until it's next turned off.
So if you need XP mode (as I do for some work applications) the (crazy) work around might be to install XP mode with a none bulldozer CPU (if the try, try, try again method doesn't get the installer to work) you can probably get it to
start once you change back to your bulldozer CPU by simply trying to start the installed OS a few times in short succession.
@Alex
Many thanks for looking into this!
Rob

2 problems: 1st unopened messages, 2nd cannot add personal email in setup wizard

Hi guys, I'm having a problem with my device. It seems like I cannot add a personal email adress in my email setup (from the setup wizard) When I enter this setup wizard > email setup the following appears: email setup select an email setup option [ ] I want to use a work email account with a Blackberry Enterprise Server AND THATS THE ONLY OPTION I CAN PICK! (a friend of mine with the same device could add a personal email) from there I can only choose { close } or { next } what is happening, can someone explain what I can do to add my personal adress? ------------------ Another thing I find quite strange is the fact that on my desktop the icon "unopened message count" appears. When I open the BB-menu, there should be a little star in the message-icon right? Well it isn't there! (the litte white-on-red star) So this icon tells me that I have unopened messages, but I can't find them anywhere.. guys please help!!!

Hi and Welcome to the Forums!
Your first problem is carrier related -- you must have the proper data plan from your carrier (at whatever costs they charge) to enable enhanced BB functions like email. A generic data plan is not usually sufficient -- some call the required plan The BlackBerry Data Plan. But call your carrier and ask them what you need from them in order to have access to their BlackBerry Internet Services (which include personal email).
Your second problem I am not understanding. What "BB-menu" are you accessing? Where exactly is the star you are seeing? Where exactly is the star you are expecting to see? More and clearer details, please.
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

"cannot complete windows setup" Windows xp mode on Windows 7 professional

I am currently having a problem loading windows xp mode on windows 7 professional on my new laptop
Laptop specs
LENOVO
Processor: AMD A6-5350M APU with Radeon(tm) HD Grapihcs 2.90 GHz
Installed memory (RAM): 4.00 GB (3.15 GB usable)
System type: 64-bit Operating System

experiencing the same issues you are describing on what appears to be the same model of computer. Can anyone provide additional information on applying the suggested hotfix?
@Rick Dee - After installing both XP mode and Virtual PC service pack on the computer XP mode appears in the list of Virtual Machines. After running through the initial set up of the VM (Windows XP Mode) listed in ~/<user>/virtual machines, the
setup of the VM fails with the error, "cannot complete windows setup".
I use a vhd that I deploy to all my client computers to run XP mode. I have deployed this vhd on at least 5 other laptops with the same specs from the same manufacturer. On this particular machine though, when I tried to deploy this vhd, the
vm just hangs. So I have been trying to install the distributed copy of Windows XP mode from Microsoft. When I do this, I get the error.

In setup wizard it says "Your computer must be restarted to complete a previous uninstall. Do you want to reboot now?" after uninstalling old version and trying to install new. I CAN NOT run ANY version now......HELP

I had an old version of Firefox and uninstalled it. Then I installed the 5.0 version. BUT, in the setup wizard it says "Your computer must be restarted to complete a previous uninstall of Firefox. Do you want to reboot now?" I choose "YES" and the computer reboots, but when I run the setup wizard again, it says the same thing. I have reinstalled it 8 times, and it says the same thing......I have searched my computer for it, and can't find what it's talking about!! HELP!!!!!!

Cor-el:
Thanks so much for your help, it is very much appreciated.

Cannot complete wireless setup for Officejet 4500 G510n using HP Installer

Hi,
I hope someone can help me with this problem.
I bought an Officejet 4500 G510n and all was working fine on my old MacBook laptop. I have recently switched to a MacBook Air running OS X 10.8 and I can no longer connect wirelessly to this printer.
I have tried the following:
- resetting printer settings from OS X "Preferences" using USB cable.
- disconnecting USB cable to printer.
- downloading and installing the latest software drivers for OS X 10.8
- reconnect USB cable to printer to start printer setup.
The problem arrises when I am performing the set-up task:
- Screen shows invalid network details and gives me no option to continue.... only to go back to the previous page. I am stuck with no options at the moment.
Attached is the screen-shot of what I'm seeing.
Any help would be very grateful.
John

From what you describe, you are using a USB cable but the information displayed there is for wireless. What you would want to do is install the printer using the USB cable and selecting USB installation, then use the software to complete the USB to Wireless conversion.
Either this, or you can set up the printer on your wireless network using the wireless setup wizard and then install using Networked - Wireless as the installation type.
Happy Holidays!

I cannot get the Firefox setup wizard to run on my laptop, which runs Windows XP.

I have a Compaq Presario which runs Windows XP. I have 1.12 GB of RAM, a 1.59 GHz processor, and more than 30 GB of space on my hard drive. I can download Firefox, but I can't get the setup wizard to run. After I get it downloaded and try to run the wizard, my computer hangs up. I have tried both saving it and running it right off the bat. Neither way works. I need to have Firefox on my machine, so any way I could get help with this problem would be great. Thanks.

It is possible that your anti-virus software is corrupting the downloaded files or otherwise interfering with installing Firefox.
You can try to disable the real-time (live) scanning of files in your anti-virus software temporarily to see if that makes installing work.

Security Setup Wizard keeps appearing on startup

For some reason, the Security Setup Wizard keeps appearing everytime I logon. There seems to be an error when it is completing the last steps of the process. I enter all the information requested and get to the last page and I get an error message that it cannot create the "system keys." What are the system keys and how do I fix this error?
If I cannot fix the error so that the wizard can complete its tasks, how do I prevent it from running on startup in the first place? I checked the run list in the registry but it doesn't seem to be listed there.

Hi sclexman,
Thank you for your good instructions and prompt reply. I don't often see such patient or helpful people outside of the ThinkPad community!
My system has been running beautifully for well over a year.
I am running Windows XP Professional on my IBM ThinkPad T60p.
Typing something like ThinkPad "Security Setup Wizard" into Google with quotation marks, you will get better results.
I literally get exactly what is described above by the other people.
My problem is the Wizard which keeps popping up every time the computer restarts, but the "system keys" step is where the wizard gets stuck, so I thought that might be the cause of the problem.
I put off setting up my security software with fingerprint reader for years, and I just got around to it yesterday. The wizard popped up every time I started up since I got it, but when I went through the wizard and set everything up, it finally stopped popping up.
Shortly after, I went poking through the advanced settings of the ThinkVantage Client Security Solution program and accidentally clicked "Reconfigure security settings". This brought up the same wizard again, and made me re-enter all of my passwords and security questions, which was quite a hassle. This is the time it failed at the "system keys" part of setup; the first time took longer, but it was successful.
My big reward at the end of this was supposed to be the wizard leaving me alone at startup, but he will not stop his familiar haunt!
Any help is appreciated.
Thanks,
Thomas
Security Setup Wizard that won't stop popping up:
Wizard after initial successful completion. If done over, it won't get past the second step.
I don't want to try creating my own system key as your WikiHow link describes, as I'm not entirely sure what I'm doing, and I don't want to actually break my system's security! Everything is working perfectly now security-wise, except for this pop-up window!!!
P.S.
I took so long to reply because when I tried to change my e-mail address to the one I check most often, I was completely locked out of my account. I did not receive any confirmation e-mail no matter how many times I clicked re-send. Today I changed it back to my Hotmail account, and it came within five minutes, so I'm back in. Since Hotmail works, I am guessing that the spam filter on my school's e-mail servers is cranked up too high, rather than any problem on Lenovo's part.

WiFi Wireless Setup Wizard produces Blue Screen of Death on Officejet Pro 8600 Plus

The wireless setup wizard on my Officejet Pro 8600 Plus is failing immediately after "scanning for networks". I get a blue screen of death with error message B8494B00, followed by "turn printer on and off" with flashing screen.
I bought the printer about one month ago and it has worked perfectly so far. My Apple Time Capsule failed yesterday, so I bought a new one (latest model) and had to set up the wireless network again. When I tried to do so on the printer, I got the error for the first time. Nothing else had changed. Other devices are working with no problems on the new network. The computer is an Apple iMac running OS Mountain Lion.
I have tried turning the printer on and off, disconnecting the power and reconnecting, then turning it on again, but no result. I have restored the wireless to factory settings, but no difference.
Please help.

Right off I have to tell you I do not "speak Mac".
I assume the "Apple Time Capsule" is a name for a network router? A syncing device?
Unless I am mistaken:
You do not need the Wizard to set up the network -- it is pretty software for an HP PC; when it works, it can make things easier. The setup Wizard is not necessary for the process. I should think this is true for the Mac.
=====================================================================================
If you cannot get someone from the Printing group to answer your specific concern,
you may have succes with the following:
The User Guide has pretty good detail on how to set up the networking necessary to get the printer connected to either a PC or Mac environment. Assuming you can get the printer to "Reset network settings" (User Guide, page 222), then you can re-enter the information you require manually. It is a bit tedious, but is may work better than fighting the Wizard.
OfficeJet Pro 8600 User Guide
You may be able to circumvent sone or all of this by reinstalling the Full Feature Software for your printer -- that assumes you are first able to "reset network settings", at least, and get a printout test page to verify that the reset actually worked.
Select your printer from HP Office Jet 8600 series
Mac – By Garland_M
HP Wireless Printer Setup (Tutorial Video)
Mac
YouTube Search - HP printer install for mac
Good Luck!
<<< Click on the White Kudos Star on the Left to say Thanks!
Clicking “Accept as Solution" helps others find this fix for a same or similar issue >>>
2013 Year of the Snake!
Kind Regards,
Dragon-Fur

I am getting error code -9808 saying cannot complete request for the i store, i am getting error code -9808 saying cannot complete request for the i store

i am getting the erorr code -9808 saying that we cannot complete my request for the i store to setup my new device ...what up with that

Try here:
iTunes Store: "An unknown error occured (-9808)"

Diagnostics System: Managed System Setup Wizard

Hi there!
I have installed the Host Agent and Diagnostic Agent on a test-system successfully. Now I have tried to start the Setup Wizard for managed systems (http://<hostname>:port/smd). The system collection was no problem, but the Setup Parameters. If I choose the directories of the "System Install Path", the "Instance Path" and also the "Instance Number" the following Message appears: "No Diagnostics Agent available at this time Please install or start an SMD Agent for <hostname>".
I don't know the reason, because the Diagnostic Agent is running and I think my parameters will be okay:
System Install Path: usr/sap/DAA/
Instance Path: usr/sap/DAA/SMDA97/
Instance Numer: 97
Is there a failure?
I look forward to your reply!
Best reagrds,
Andreas

Hi there!
I have found an interesting warning:
Managing System '<hostname>' is registered in the SLD but the CIM declaration is not valid, the agents cannot be attached correctly. check SLD Managing system declaration. (detail: CIM_ERR_FAILED: Cannot find SAP_BCCentralServiceInstance of SAP_J2EEEngineCluster SAP_J2EEEngineCluster.CreationClassName="SAP_J2EEEngineCluster",Name="<hostname>" in SLD LR)
I think it is the reason for my problems .. Can anybody help me?
Best regards,
Andreas

Cannot Complete Setup Wizard

Similar Messages

Maybe you are looking for